You are here:
- Home
- Autos
- Auto Repair
- American Motors
American Motors/Questions Answered by Expert Kevin Pilotte
| Subject | Date Asked |
| how to tell the difference between#1 compresstion rings | 2/19/2011 |
| Q: how do i tell the difference between the top and the #2 compressyion rings they got mixed up they ... A: The top two grooves are the same size. Usually, the #2 ring has a bevel which faces downward ... | |
| 1965 Marlin | 2/14/2011 |
| Q: Kevin, just purchased a survivor Marlin with a 287 automatic. Car is out of Arizona and in very ... A: The AMC 287 & 327 are identical engines, with the exception of the CID. The 327 AMC engine will drop ... | |
| brake lights | 2/2/2011 |
| Q: turn signals , marker lights , and dash note lights don't work neither does the gas gauge or temp ... A: Sorry, I do not have a wiring diagram for your 66 Ambassador, try to find one. There is a CVR ... | |
| Neutral safety and B/U switch for saginaw column | 2/2/2011 |
| Q: Kevin, I am in the process of installing a small block Chevy and TH 350 in my 84 CJ7 which was ... A: I think the easiest thing for you to do is visit your local salvage yard and find a GM vehicle with ... | |
| 1964 Rambler Classic 770 | 12/7/2010 |
| Q: I can't figure out how to remove the rear drum on my '64 Classic 770. It has a leaking wheel ... A: The drum is probably rusted to the axle hub. Saturate the area where the drum & hub meet (right in ... | |
| tech manuals | 9/25/2010 |
| Q: My son and I (he's 16) just bought a 1964 AMC Rambler 330. We had the brakes redone by a local ... A: Here's a 66 Rambler American repair manual that you will find helpful: ... | |
| 63' Classic 770 Steering | 9/24/2010 |
| Q: What you described sounds close to the problem I have with one exception. The slop in the system is ... A: The "ram" is called the steering gear box. It would be best to just replace the complete steering ... | |
| Steering bushing for 1963 Classic 770 | 9/24/2010 |
| Q: I have a 63' Classic 770(287 w/TorqueFlite 727) that I'm having steering issues with. It's got power ... A: What you are describing sounds like the pittman arm mounted on the steering sector shaft. Do you ... | |
| Pacer Engine Noise | 9/17/2010 |
| Q: I have a 1975 Pacer with the 258 I6. The engine has 244,989 miles on it (un- rebuilt) and it has a ... A: It is possible the lifters are noisy, but more likely the rocker arms and rocker arm bridges are the ... | |
| 1978 amc amx | 9/15/2010 |
| Q: .ive found a 1978 amx..the engine compartment sticker say its a 304..the owner says its the real ... A: I don't know the number of units made, though I am sure that could be located online. As for the ... | |
| 69 rambler | 9/15/2010 |
| Q: Hey Kevin, just trying to see if someone can help me out..there's a 69 rambler near me for 3k that ... A: If the car is in very good shape, it might be OK. I would suggest having a qualified technician ... | |
| 78 CJ w AMC 304 | 9/7/2010 |
| Q: I have an original 78 CJ w the AMC 304. I would like greater performance and am considering porting ... A: Don't know how much more power you want from your 304, but porting & polishing the heads and ... | |
| Exhaust system 4 max torque | 2/26/2010 |
| Q: I've got a J10 with rebuilt 60 over 360. Runs great now w/500 2bbl and stock iron exhaust and ... A: Anything you do to reduce the backpressure created by the stock exhaust will increase the torque AND ... | |
| Exhaust system 4 max torque | 2/26/2010 |
| Q: I've got a J10 with rebuilt 60 over 360. Runs great now w/500 2bbl and stock iron exhaust and ... A: The longer hedders will give you more torque, but with the layout underneath, you might consider ... | |
| oil pan removal | 2/22/2010 |
| Q: how do i remove the oil pan from my 1963 rambler 287 v8 A: Gain access to the pan by: 1) Removing the engine 2) Dropping the front crossmember and suspension ... | |
| 1974 360 Javelin broken teeth on flexplate | 2/20/2010 |
| Q: Think that I put the distributor in 180 out. Turned engine over, backfired while starter was ... A: If it has been sitting for 4 years and you would like to do some performance modifications, I would ... | |
| 65 rambler 330 rear end | 2/20/2010 |
| Q: i have a 1965 rambler 330 2 door and would like to know what rear end is in the car and how strong ... A: It has a 7 9/16" ring gear, not very strong or desireable; especially for a small block Chevy. The ... | |
| Pacer Problem | 2/19/2010 |
| Q: I have a 1975 Pacer with a 4.2 258 I6. Recently the car has been bucking at low RPM. Recently all ... A: A weak ignition coil will usually show bad when under load, as during hard acceleration. The most ... | |
| points to electronic distributor | 2/18/2010 |
| Q: I was wondering if there is a conversion to change from a points distributor to a electronic,I ... A: I do not know if this conversion kit will fit a Prestolite distributor, but you can ask the company. ... | |
| hei | 2/13/2010 |
| Q: I just put a hei distributor in amc 360 in 76 cj5. the vacuum advance is in the way of power ... A: What you are doing is changing the position of cylinder #1 on the distrbutor cap. This will allow ... | |
| headlight remove & replace | 2/9/2010 |
| Q: What is the best way to install a headlight switch in a 70 AMX. Is it necessary to remove the upper ... A: Locate the switch behind the dash. Depress the release button while pulling out on the knob. Once ... | |
| ignition | 2/5/2010 |
| Q: i have a 74 amc matador 304, the problem is that when i crank over the car it will only run when its ... A: I've attached a page from the repair manual, along with a link to the second page. Follow the ... | |
| 1978 Jeep CJ7 | 1/29/2010 |
| Q: I have a problem after replacing the ENTIRE fuel system on my 1978 Jeep CJ7 V8 304 I now thing I ... A: The eccentric is located on the front of the camshaft and is the same for all AMC V-8 engines from ... | |
| what is the tube coming off my valve cover for | 1/20/2010 |
| Q: hay Kevin thanks for the wire diagram. Everything worked out great. So my question for you this time ... A: You are correct. The hole in the valve cover is for a crankcase breather. It must be there to allow ... | |
| 1976 DJ5 Jeep Wiper Blades | 1/18/2010 |
| Q: I am looking for replacement blades for my RHD mail jeep. The ones on it are 11 inches long. Any ... A: The best I can recommend is bring your blades to your local NAPA auto parts store and try to match ... | |
| 2007 Ford Focus Coolant | 1/17/2010 |
| Q: The coolant appears low. Manual says to add 50/50 mixture of coolant and distilled water. Also ... A: There is two ways of doing it. 1) Buy a gallon of QUALITY coolant/antifreeze. Mix it 50/50 with ... | |
| wire diagram for amc javelin 304 | 1/15/2010 |
| Q: so heres the problem or the question for that matter. I'm wondering if you have a picture of a wire ... A: I've attached a copy from an AMC repair manual showing the location of the spark plug wires. If you ... | |
| 1964 Rambler classic | 1/9/2010 |
| Q: My car has the 287 V-8 w/flashomatic trans.How feasable is trading out to a small block chevy & ... A: How feasable is subjective. If you have the money and time, anything is possible. It is NOT a simple ... | |
| Pacer Won't Start | 1/8/2010 |
| Q: I have a 1975 Pacer with the 4.2L 258 I6 and a three speed manual with overdrive. The car had been ... A: Three things are necessary to get your Pacer running, and they must occur in the proper order. 1) ... | |
| amc pacer front disc brake conversion | 1/7/2010 |
| Q: I have a 1953 Chevy pickup with a AMC pacer front end. I thought it was a 1978 but through my ... A: Pacer front ends were the same from 75 up. They did, however, use different make calipers. 75-76 ... | |
| bulb replacement question? | 1/2/2010 |
| Q: Question The small bulbs on my speedomoter and tacometer went out and I have removed the instrument ... A: I do not have a listing for the bulbs on later model vehicles. You should, however, be able to bring ... | |
| 64 amc rambler ambassador 990 H | 12/31/2009 |
| Q: I have my hands on a 64 amc rambler ambassador 990 H it is overall great condition. The engine is ... A: Installing any engine besides the original 327 AMC will require modification. Besides, the AMC is ... | |
| 65 Rambler american instrument cluster removal. | 12/30/2009 |
| Q: What do I have to do to remove the instrument cluster on my 65 Rambler American so I can replace the ... A: You should be able to remove a few phillip head screws and pop the instrument cluster out. Place a ... | |
| just bought a 1964 amc rambler classic | 12/25/2009 |
| Q: vin# is G540183, on engine block # j173, 3168465, I understand its a 6 cyl the engine runs well but ... A: I don't understand what your quesiion is. Is there currently an oil filter on the engine? It should ... | |
| 1960 rambler super | 12/19/2009 |
| Q: it looks like something from the manifold to the carb is missing.A small tube with threaded ends if ... A: What you describe sounds like the choke heat tube. Its job is to provide heated air to the automatic ... | |
| broken pipe where oil dip stick goes on 304 amc | 12/18/2009 |
| Q: So here it is i have a 1970 amc javelin with a 304. Somehow the pipe where oil dip stick goes broke ... A: I have experienced the same thing. Unfortunately, your engine is in the car. Try using an E-Z out ... | |
| starter motor AMC Hornet 232-1977 | 12/11/2009 |
| Q: I have a Hornet 1977, engine 232, 6L.The starter donīt work perfect, several times I have to turn ... A: It sounds as though the flywheel has damaged teeth on the gear. This is not uncommon. I do not know ... | |
| 1976 amc 304 distributor timing | 12/11/2009 |
| Q: I just bought a 76 cj5 with 304 and a howell tbi kit installed by previous owner. my question is, ... A: You can inspect the timing gear & chain, but it would require a bit of work to access it. The ... | |
| classic 550 | 12/9/2009 |
| Q: since my Rambler has only 38k miles since 1964 should I repaint it? because it runs like new and ... A: It depends on whether you want to keep it original or not. An original paint job will make the car ... | |
| 1976 amc 304 distributor timing | 12/3/2009 |
| Q: I just bought a 76 cj5 with 304 and a howell tbi kit installed by previous owner. my question is, ... A: Check the firing order. It should be 1-8-4-3-6-5-7-2 Also, the engine can pop like you describe if a ... | |
| oil pan removal | 12/1/2009 |
| Q: Hey Kevin i have a 1960 american with a flat six. One of my piston rods may be broken and who knows ... A: No. I have attached a page from the repair manual on oil pan removal. If all of the bolts are out, ... | |
| 1959 instrument clustrer | 11/30/2009 |
| Q: Can you describe what is necessary to change out the temp gauge on my 59 custom. I have checked all ... A: You will have to remove the instrument cluster. Remove the circuit board on the back of the cluster ... | |
| FUELPUMP | 11/24/2009 |
| Q: i was wondering if there was a trick or something to insalling the vacume fuel pump, i worked for 3 ... A: Being that the fuel pump on this engine is driven by a large eccentric on the front of the camshaft, ... | |
| hard starting | 11/13/2009 |
| Q: i have a 1983 jeep CJ5, the engine is rebult with about 1000 miles on it. i put a new carb on it. I ... A: Remove a spark plug wire from a spark plug and hold the end about 1/2" away from the engine block. ... | |
| vacuum hoses and carb adjustment | 11/8/2009 |
| Q: I have a 1970 Javelin with a 258 6 cyl engine and a one barrel carb. Where does the vacuum advance ... A: You would want ported vacuum to the distributor, that's the port that has vacuum when you start to ... | |
| hard starting | 11/5/2009 |
| Q: i have a 1983 jeep CJ5, the engine is rebult with about 1000 miles on it. i put a new carb on it. I ... A: Did you install the Weber carburetor? It sounds like the engine is starving for fuel. Before ... | |
| 66 amc dpl flashomatic transmission | 11/3/2009 |
| Q: I have a 1966 AMC DPL with its original Q code 327 4V and column shift flashomatic trans.The car ... A: I feel your pain. It has been over 35 years since I pulled a starter on a 327. All I remember is it ... | |
| electronic ignition | 11/2/2009 |
| Q: I have a 64 American convertable I am restoring. I took an electronic ignition distributor and ... A: Gord, Need to know what year distributor you have. It is either a Prestolite or Motorcraft. Pull ... | |
| 1969 AMX 390 FUEL PUMP MECHANICAL WITH VACUUM WIPERS. | 10/28/2009 |
| Q: What is the correct way to remove and replace the fuel pump on a 1969 390 AMX? Also how much Vacuum ... A: Remove the fuel lines from the pump, remove the vacuum lines from the pump, remove the bolts then ... | |
| amc javelin & ambassadore | 10/22/2009 |
| Q: are the frames on the ambassadore (72) and javelin (71) the same ? ANSWER: Technically, these are ... A: You're in luck. Numerous components will interchange. Front suspension & steering; brakes & brake ... | |
| 1966 rambler amc | 10/21/2009 |
| Q: i just got my hands on a 66 rambler been taken good real good care of the body and interior. but im ... A: You say you have power going into the coil; you should have 9-12V on the (+) side of the coil when ... | |
| 88 Eagle Premeir In colum Ignition switch | 10/21/2009 |
| Q: To solve some questions, in mid-year of 1988 AMC switched the location of the ignition switch from ... A: I do not have any local sources for later model Renault Eagles nor am I familiar with them. If my ... | |
| Jeep t-5 transmission | 10/19/2009 |
| Q: My jeep cj7 made a loud pop as I started out in first gear and then began to click loudly. The ... A: Try removing the rear driveshaft; place it in 4H; and drive it off the front wheels. If the noise ... | |
| owner's manual of a '63 Rambler classic 550 2D | 10/10/2009 |
| Q: Mr Pilotte, I just got a '63 Rambler 550 Classic 2D as a gift from my uncle. This car is not running ... A: The best place to start looking is online AMC vendors and AMC/Rmabler clubs. Google 1962 Rambler and ... | |
| Jeep CJ Steering Column Gear Indicator | 10/9/2009 |
| Q: I have a 81 Jeep CJ with GM steering column. What type of column is this? I am trying to find a ... A: The steering column is made by Saginaw, a GM subsidary. There are parts that are interchangable from ... | |
| no fuel from tank | 10/7/2009 |
| Q: please help i recently got a 1966 rambler classic 770 232 six but i cant get any fuel from the tank. ... A: It is possible that the pick up sock in the tank is restricted or clogged. It will require the ... | |
| generator wires | 10/3/2009 |
| Q: just picked up this cool 64 American. the wire from the generator smokes? A: The car is over 21 so it is legal to smoke. Just kidding. If a wire is smoking it usually means ... | |
| 1985 jeep cj7 | 10/2/2009 |
| Q: HAVE INSTALL MOTORCRAFT 2100 ON MY 1985 CJ7 IT WILL NOT IDLE ANY ANSWERS AND LOOKING FOR PICTURES ... A: If you removed the carburetor from a vehicle that hasn't been running for a while, it might need to ... | |
| 1974 AMC JAVELIN -IGNITION- | 10/1/2009 |
| Q: I am having Ignition problems with my 1974 Javelin - 304 2bbl. - Car has started and ran by jumping ... A: 1974 AMC vehicles came with a seat belt system that required the seat belts to be connected before ... | |
| 1969 AMX question - | 9/26/2009 |
| Q: Mr. Pilotte, I run across this site and have enjoyed reading your many answers to all kinds of ... A: How much money do you want to spend? One option would be to find an AMX with a good body and ... | |
| circuit board for 69 Rambler | 9/25/2009 |
| Q: Who do you suggest I contact to purchase a new or used circuit board for a 1969 Rambler, Thanks A: If you are unable to find one online from one of the numerous AMC parts vendors, call Collier AMC in ... | |
| 1966 Marlin | 9/25/2009 |
| Q: I bought the car and they had had the fuel tank boiled out and coated new fuel lines put on...car ... A: Hook up a fuel pressure gauge at the carburetor and measure the fuel pressure. Have you replaced ... | |
| AMC 304 running rough and backfiring | 9/16/2009 |
| Q: My Jeep 304 just cut out on me one day. Replaced all ignition components and carb. I found a broken ... A: Some things that can cause backfiring is a broken valve spring or rocker arm bridge support; spark ... | |
| Timing | 9/13/2009 |
| Q: Kevin, Thanks for your help on the previous question. I have another. with timing at 10-14 initial ... A: Ahhhh, Another piece is added to the puzzle. A non-stock cam can give you those manifold vacuum ... | |
| Timing | 9/11/2009 |
| Q: Kevin, Thanks for your help on the previous question. I have another. with timing at 10-14 initial ... A: As long as you don't have ignition ping. When you say intake pressure, do you mean manifold vacuum? ... | |
| 1969 AMX REAR MAIN SEAL | 9/9/2009 |
| Q: Can I replace the rear engine main seal in my 1969 390 AMX without having to remove the engine? If ... A: Yes, but it's not easy. You have to remove the transmission & bellhousing. You also have to remove ... | |
| 94 camry problems | 9/4/2009 |
| Q: I'm driving this 4-cyl A-trans car for about 35000 miles now (Its current mileage 144000). Did oil ... A: What was damaged and what was repaired after your accident? The AC could have developed a leak, or ... | |
| 1974 amc javelin | 9/3/2009 |
| Q: i have a 1974 amc javelin automatic on the column i needed to replace the key lock and when we ... A: Look on page 10-32 at this site: ... | |
| temp/fuel gauge | 9/2/2009 |
| Q: i have a 1969 amc javelin sst, the temp and fuel gauges used to work, now they don't, i ckecked all ... A: It is possibly the CVR, Constant Voltage Regulator mounted on the circuit board on the instrument ... | |
| replaced alternator now no power 66 marlin | 9/1/2009 |
| Q: I had my motorola alternator rebuilt. I took a picture of the 4 wire connections and believe it or ... A: It's possible that you shorted the diode trio in the alternator when you connected the battery. ... | |
| Fuel indicator in 1982 AMC EAGLE | 8/31/2009 |
| Q: Vehicle is in excellent condition with 53,000 miles. Dash fuel indicator is now stuck on "full". Is ... A: Disconnct the wire at the tank from the sending unit. If the gas gauge goes down, replace the ... | |
| engine trans switch to wrangler | 8/28/2009 |
| Q: I would like to put a 360 Jeep truck engine and auto trans and transfer case in my 1993 Wrangler. ... A: Is it possible? Yes. Can it be done with shade tree modifications? No. Your 93 Wrangler was not ... | |
| possible vapor lock???? | 8/23/2009 |
| Q: Kevin I have a 1978 Jeep Wagoneer.360,4bbl,auto with 150,000 miles . Motor has 20,000 since rebuild. ... A: There are other items that can cause your condition. Ignition coils often break down when hot & ... | |
| 66 Marlin stallls but it appears it's the alternator | 8/23/2009 |
| Q: Wrote you a few days ago regarding a stalling problem on my 66 Marlin. Turns out my battery went ... A: Some people have installed a Delco alternator. It might require some bracket modification. You would ... | |
| 1969 power steering | 8/20/2009 |
| Q: Kevin. Me again. I bought this Rambler American. I want to put power steering in it. I bought a ... A: There is a "sill adapter" which is a mounting plate between the steering gear and the frame. You'll ... | |
| 66 Marlin stallls | 8/19/2009 |
| Q: Recently my 66 Marlin(287) has started to stall when I come to a stop. It usually cranks up again ... A: It does sound like a carburetor problem, the idle circuit to be exact. That is the part of the ... | |
| Vacuum leak. | 8/18/2009 |
| Q: How can you detect a vacuum leak. A: 1) listen for a hissing sound 2) place a piece of vacuum hose to your ear and move the other end ... | |
| 1968 Rambler door lock | 8/15/2009 |
| Q: Kevin. I just bought a clone SCRambler from ebay, and was very surprised that there is no way to ... A: There should be a paddle shaped lever located in the arm rest or a button on the top of the door. ... | |
| Stalls | 8/15/2009 |
| Q: I Have A 1987 AMC Eagle And Have Replaced Everything On It Till I Am Blue In The Face It Runs Out ... A: Before I list the number of things that could cause this condition, please tell me what all you have ... | |
| 1963 660 fuel gauge | 8/12/2009 |
| Q: I recently picked up a gem of a wagon. Fuel gauge does not work, stuck on E. Do you have any tips ... A: Before removing the instrument cluster to get to the gauge, why not see if it works. Remove the ... | |
| 1965 Rambler Marlin will Not Shut Off | 8/11/2009 |
| Q: I need some help. I have a 1965 Rambler Marlin with a 327 V8. My question is that even when I turn ... A: Check the wiring from your ignition switch to ignition coil. Locate a wiring diagram for a pre-1970 ... | |
| 79 amc amx | 8/10/2009 |
| Q: My son brought home a 79 amc amx there are no keys for this car. is there anyway to "hotwire" this ... A: Run a wire from the + side of the battery to the + side of the ignition coil. This will provide a ... | |
| discs draging | 8/6/2009 |
| Q: i have a 65 marlin with a disc brake conversion on it and the calibers are draging they are from a ... A: I don't have a part number for your paticular application, but it you get a master cylinder for an ... | |
| discs draging | 8/3/2009 |
| Q: i have a 65 marlin with a disc brake conversion on it and the calibers are draging they are from a ... A: It is possible you have a problem with the master cylinder or the push rod adjustment between the ... | |
| electrical issues | 7/29/2009 |
| Q: Had a couple of interesting problems yesterday upon driving my car (68 AMX) and wondered what your ... A: Sorry, Constant Voltage Regulator. It's a small component plugged into the back of the printed ... | |
| oil to use in classic car | 7/29/2009 |
| Q: IT WAS SUGGESTED I USE A/40 rather than 10/30 in my newley acquired 66 Rambler classic 770 with the ... A: You should not have a problem using 10W30 or 10W40 in your 232. Adding STP will only make the oil ... | |
| 68 Rebel Engine | 7/27/2009 |
| Q: i have a 68 rebel with a sad 290, i am considering a replacement purchase of rebuilt 360 long motor, ... A: Yes, the 360 should be a bolt in. All the accessories you mentioned will bolt up, too. If your ... | |
| 1967 amc marlin | 7/26/2009 |
| Q: How do you remove the rear brake drums on 1967 AMC Marlin? Do they just pull off as other cars, or ... A: There are usually 3 bolts that secure the drum to the hub. Often, rust will also cause a problem. If ... | |
| Fuel Tank | 7/15/2009 |
| Q: I am driving a 2008 Santa Fe 6 Cylinder. With the cost of fuel today I like many people,only let the ... A: This is an old wives' tale. I do not know anything about a Hyundai, but your fuel tank is not going ... | |
| 1964 Rmbler Classic 550 | 7/14/2009 |
| Q: Just picked this gem up for my son. It has 27774 original miles and has been sitting off and on over ... A: The oil leak will involve some work. I suggest going to this web site and purchasing a 1964 Rambler ... | |
| javelin sst | 7/13/2009 |
| Q: I have a 71 sst with 304 in it. I am considering buying a 904 to replace my borg warner, but I was ... A: The 904 tranny has to come from an AMC. Also, the crankshaft from your 71 will not work with a 904. ... | |
| 1982 CJ7 ignition. No spark | 7/10/2009 |
| Q: I have a 1982 CJ7 with a stock 4.2L carbureted engine that won't start. The problem is ... A: I have to start off by telling you my experience with post 79 AMC/Jeep vehicle is VERY limited. That ... | |
| 1974 AMC 360 V8 leaking oil... | 7/8/2009 |
| Q: My 1974 AMC matador's engine recently began leaking oil from what appears to be the front right ... A: The most common oil leak you are describing is from the vavle cover gasket. Second would be the ... | |
| '79 AMC Concord OIl Pump & RMS | 7/6/2009 |
| Q: Changing the RMS looks like it'll require my removing the transmission. True? However I do it, ... A: Yes, you will have to remove the transmission. The oil pump is subjective. It has been submerged in ... | |
| replace rear main seal | 7/6/2009 |
| Q: In a 1979 AMC Concord (2wd) what's the easiest way to change the rear main seal? Should I raise the ... A: The easiest way? Send it out to a garage. Really though, you can loosen the front motor mounts and ... | |
| overheating AMX#4 | 6/27/2009 |
| Q: Facts: '68 AMX, 390 4sp., stock engine (except for mod. cam), total timing of 38 deg. or so, engine ... A: All the coolants mixed 50/50 will do about the same job in cooling your engine. The basic ingredient ... | |
| overheating AMX#2 | 6/27/2009 |
| Q: Facts: '68 AMX, 390 4sp., stock engine (except for mod. cam), total timing of 38 deg. or so, engine ... A: Did the overheating occur after the engine was rebuilt, or before? If you have a lazer temperature ... | |
| overheating AMX | 6/27/2009 |
| Q: Facts: '68 AMX, 390 4sp., stock engine (except for mod. cam), total timing of 38 deg. or so, engine ... A: The easiest thing to try is an auxillary electric fan. You might mount it in front of your radiator ... | |
| 79 cj 7 | 6/25/2009 |
| Q: I have a 79 cj 7 with a 304 v8 in it. My vaccum advance is bad and i cant find one. Where can i ... A: Being a Motorcraft distributor, you should be able to at least find a distributor that will fit your ... | |
| 61Rambler American haunts me 40yrs. | 6/19/2009 |
| Q: Purchased new base 2 dr coupe had either no start or stall problems from the get-go dealer never ... A: Here are a few things that could have caused the condition: 1) Misadjusted or defective neutral ... | |
| 66 classic 770 convertible | 6/15/2009 |
| Q: At age 71 am I chasing a"Purple COW" in purchasing this with the 232 engine, as a drive and go car? ... A: Sorry, but I don't know what a "purple cow" is, but I have some suggestions for you. If you like the ... | |
| 1974 AMC Matador X Rear Bumper Guards | 6/10/2009 |
| Q: Next year, I will be fully restoring a 1974 Matador X Coupe. The only item I am in need of, is the ... A: There is an old AMC dealer in Pikeville, NC named Collier AMC. He has about 200 old AMC's sitting ... | |
| '86 Jeep CJ7 | 6/7/2009 |
| Q: My '86 Jeep CJ 7 will start, but dies as soon as I release the key. All to no avail,I have replaced ... A: The ignition switch (located at the base of the steering column) must be properly adjusted. It can ... | |
| AMC Marlin | 6/7/2009 |
| Q: I have a 66 Marlin. My front brakes are shot is there any other brake assemblies that will work on ... A: Try using calipers, spindles and rotors from a later model AMC. There are idle mixture screws on ... | |
| Pacer won't start. | 6/3/2009 |
| Q: I have a 1976 Pacer with the 4.2L 258 straight six (1 barrel carb) and it was put in storage 4 ... A: How fresh is the gasoline? If you have spark and compression, are you getting gas down the ... | |
| changing master cylinder | 4/24/2009 |
| Q: i just changed my master cylinder due to no brakes, when i went for a test ride after completion my ... A: Did you bench bleed the master cylinder? Does the new master cylinder look like the old one? Did you ... | |
| rear axles | 4/22/2009 |
| Q: i have a 1974 amc Hornet. it has a 360 motor. i have modified the motor. it runs 12's in the quater ... A: You can install a Ford rear end, but you'll have to do some modifications to the axle tubes for the ... | |
| 1982 amc eagle fuel gauge | 4/20/2009 |
| Q: kevin, there's a yellow box w/wires and the fuse box under the dash. is this where the wire goes or ... A: Disconnect the sending wire at the fuel tank and touch it to ground with the key on. The gas gauge ... | |
| 66 Rambler Classic interior | 4/14/2009 |
| Q: IS it possible to buy complete interior kits for a 66 rambler classic ? A friend just bought one for ... A: There are no companies that make a complete interior kit for your Clasic, that I know of. I suggest ... | |
| rambler marlin | 4/13/2009 |
| Q: i have recently purchased a ramble marlin and it needs a lot of work. i am having trouble finding ... A: The best thing you can do is talk with others who also have a Marlin. Google "AMC Marlin" and check ... | |
| 66 classic disc brakes | 4/3/2009 |
| Q: Kevin is it normal for the disc brakes on this model to have a lot of drag compared to modern ... A: It depends on what you consider a lot of drag. Disc brakes as originally designed on cars do not ... | |
| Car Exhaust | 4/1/2009 |
| Q: 1. Why is car exhaust sometimes invisible? 2. Why is it sometimes visible? 3. Is fuel related to ... A: 1) The primary gases coming out of the tailpipe are CO, HC, & NOx, When properly burned in a ... | |
| 79 AMC Jeep CJ5 bleeding brakes | 3/31/2009 |
| Q: I replaced my brake lines and master cylinder. I bench bled the mc before I installed it. The ... A: There is a special service tool used to disable the metering valve portion of the combination valve ... | |
| 84 cj7 carb problem | 3/25/2009 |
| Q: Not sure if it is the carb. I purchased the cj about a month ago and the seller told me that it ... A: 1) A restircted fuel filter would affect the engine performance at higher speeds as in starving the ... | |
| AMC ENGINE BLOCK NUMBER | 3/24/2009 |
| Q: I have an engine block casting number from a 1974 AMC Hornet. Where can I go to find out what this ... A: 1970-1982 304 CID engine. Here is a site that will help you in the future: ... | |
| 88 amc eagle | 3/24/2009 |
| Q: I saw the posting of the 88 amc eagle with stalling problems. I am having the same issue. Starts ... A: Using a digital voltmeter, measure Voltage at the (+) side of the ignition coil with the key on. ... | |
| 88 amc eagle | 3/24/2009 |
| Q: I saw the posting of the 88 amc eagle with stalling problems. I am having the same issue. Starts ... A: When the ignition switch was replaced, was it properly adjusted? This is the switch on the steering ... | |
| borg warner A-12 automatic | 3/19/2009 |
| Q: I found a 1969 Javelin SST with a 390 auto...I look at the trans and it is a borg warner A-12 I look ... A: AMC used Borg Warner automatics thru 1971, then switched to Torque-Flites. The B-W isn't known as a ... | |
| starting a 304 after sitting | 3/17/2009 |
| Q: I have been rebuilding a 79 cj5 and it hasn't been running for over a year.The previous owner said ... A: 1) Change oil & filter. 2) Remove spark plugs and spray a teaspoon of oil into each cylinder 3) ... | |
| 1979 Jeep Cherokee Gas Gauge | 3/17/2009 |
| Q: I have a 1979 Jeep Cherokee and the fuel gauge reads empty. I've traced the wire from the sending ... A: 1) Disconnect the sending unit wire from the tank and ground it. 2) Turn the ignition key on. 3) If ... | |
| 304 year changes | 3/13/2009 |
| Q: I have a 1979 304 in a cj5. I understand that the 79 engine has about 30 horsepower less than the ... A: The engines in 1979 sufffered from Uncle Sam's involvement. Emissions. Different cylinder heads were ... | |
| 85 CJ7 Carb Problem/Starting Problem | 3/12/2009 |
| Q: I have an 85 CJ7 Automatic. When I try to start the jeep it will not start no matter how many ... A: First thing after the vehicle is cold try this: DO NOT START THE ENGINE!!! 1) Remove the air cleaner ... | |
| water in oil | 3/11/2009 |
| Q: got a engine that was just rebuilt, left the valve covers off to adjust valves, rained and water got ... A: How long was the water in the crankcase? Could be rust on the inside got into the bearings and wiped ... | |
| 304 rockers | 3/9/2009 |
| Q: #1 What years did not have bridged rockers? #2 I tightened the nuts holding my rockers on. Did not ... A: 1) V-8 bridge rockers were used starting in 1974. 2) Tightening your rocker nuts are OK. They are ... | |
| 79 AMC 304 V8 Carb help | 3/7/2009 |
| Q: I have a 79 amc 304 v8 bored .30 over out of a Javelin that I put into my Jeep scrambler. edelbrock ... A: I have never used an Edelbrock carburetor so I am not familiar with it's idiosyncrasies. But basic ... | |
| 1977 AMC gremlin vaccum diagram | 11/30/2008 |
| Q: I own a 1977 amc gremlin with the 258 c.i. I6 engine, with a two barrel carb and electronic ... A: If you can locate a 1977 AMC repair manual, buy it. It will have the hose routing. Or check your ... | |
| 74 Javelin Carb Conversion | 11/24/2008 |
| Q: I noted your response re: changing the carb to a 4B on a stock 304. What model Holley would you ... A: If the 304 is not modified and you will not be modifying it, go to NAPA and get a remanufactured 4 ... | |
| Ignition problems | 11/15/2008 |
| Q: I have a 1974 scout II with a inline Amc 258, I have 12 volt going to my coil and when I hook up the ... A: Touch a 12V test light to the negative side of the ignition coil while cranking the engine, it ... | |
| 1979 CJ7 258-6 Problem | 11/12/2008 |
| Q: Problem is at a constant speed above 50 mph the engine will lose power as if starved for gas.This ... A: It is possible the engine is starving for fuel. Check the pick up sock in the tank for ... | |
| 1974 (?) 304 engine vacuum lines | 11/11/2008 |
| Q: I just picked up a '74 304 Hornet hatchback, the valve cover tag codes out to be a '71 engine, is ... A: It is possible the engine has been replaced, it's a simple swap. As for the vacuum routing, there ... | |
| Re: Ignition Switch | 10/30/2008 |
| Q: ... I need to replace the ignition switch with keys for a 1965 Rambler Ambassador 4-dr 990. After ... A: Companies still making the switch I don't know. However, here are 3 vendors that specialize in old ... | |
| amc V8 timing covers and oil pumps | 10/26/2008 |
| Q: I have a 68 290 CID, a 68 343 CID, and a 69 390 CID engines, as well as an 83 360 CID. When the 360 ... A: There is no repairing the oil pump on an AMC engine. There is, however, new timing cover housings ... | |
| windshield removel | 10/24/2008 |
| Q: i want to take out my windshield from my 65 american 2 door i am restoring before i paint it. i am ... A: If you have never removed a windshield before, I would STRONGLY recommend having a professional do ... | |
| 1974 Gremlin x V8 (304) | 10/22/2008 |
| Q: my carburetor on my 304 is an motorcraft 4TA4 AA, and I like to replace it with an newer one, what ... A: You have basically 2 other choices. 1) Holley 600 w/vacuum secondaries. Been around for a long ... | |
| Brake differential pressure switch | 10/18/2008 |
| Q: Kevin, After checking all of the parts houses in my area and not being able to locate a brake ... A: You should not run your vehicle without that valve. You have disc brakes on the front and drum ... | |
| Jeep CJ7 | 10/16/2008 |
| Q: I recently purchased an '81 CJ7 w/258-6 4sp. It has alot of issues, most of which I've got ... A: Visit you local salvage yard and ask to see their interchangability book. In it you can see what ... | |
| 1983 CJ7 Brake Proportioning Valve | 9/9/2008 |
| Q: I am replacing the Brake System on my 83 CJ7. I need direction on where to get the tool to hold the ... A: That was a special service tool from AMC/Jeep. Try bleeding the system at the P-valve, this will ... | |
| turn signal switch | 9/6/2008 |
| Q: where can i find a turn signal switch for a 61 rambler American? i been looking online but no luck i ... A: Hemmings News is a good place to check. www.amonational.com is a good AMC club to join. This gives ... | |
| 1985 CJ 7 | 9/5/2008 |
| Q: My CJ does not want to idle very well. It either idles at very high rpm or stalls. I can adjust the ... A: A few things to check: 1) Try some fresh gasoline. Gasoline looses it "umphh" after sitting for a ... | |
| my 69 amx will not start | 9/4/2008 |
| Q: ok, i just put my car on the road first time sence it was rebilt and drove to town. i got back tuned ... A: Check your primary wiring. That's the wiring running from the solenoid to the ignition switch, to ... | |
| amc 20 rear | 9/3/2008 |
| Q: i upgraded my amc to one piece axles. had a professional press on the bearings. 3 months later ... A: I don't know what other rear end would fit. Check with some online Jeep websites and forums. As for ... | |
| 1983 cj7 | 9/3/2008 |
| Q: my 258 runs fine lots of power but has a clicking noise i thought it was the valve lifters so i ... A: A "clicking" noise from your engine could be 1) worn rocker arms 2) worn rocker arm pivots or ... | |
| 94 camry | 8/30/2008 |
| Q: i drive a 94 toyota camry and was wondering what it means when my car gets a little shaky in ... A: I need more information. Does this happen only after the vehicle has been sitting and the engine is ... | |
| oil leek | 8/29/2008 |
| Q: Ihave a amc 304 that is leeking oil where the top of the timing chain cover meets the block just ... A: You should make sure the surface is clean, then apply the gasket using an adhisive sealer. i.e. 3M ... | |
| 1966 rambler classic | 8/28/2008 |
| Q: i just bought the car it has 1 rear quarter panel rust / exhausts system needs replacement / some ... A: How much money do you want to spend? Seriously, if you are driving this car, the first items you ... | |
| leaky vents | 8/27/2008 |
| Q: I just got a 1974 AMX Javelin with a 401/auto trans with no AC. When it rains water comes in the ... A: It is possible you have a rust problem. Check the air intake at the base of the windshield. Look for ... | |
| 1979 AMC Concord | 8/25/2008 |
| Q: just purchased a 1979 AMC Concord. The model I purchased didn't come with power brakes or a radio. ... A: 1979 AMCs had weird sized radios. A few placed to find one would be: 1) E Bay 2) Craigslist 3) ... | |
| 72 cj5 wont start | 8/19/2008 |
| Q: Have a 72 cj5 that will crank but wont fire. Used starter fluid and only get loud popping from the ... A: You need three things happening at the right time to get your engine running. 1) Gas. Is the ... | |
| 78 360 engine ID | 8/18/2008 |
| Q: My nephew just got a 78 Cherokee w/ 360 turbo 400. I'm very familar with GM and remember some ... A: I do not know why it would be painted red, unless someone painted it. Look on the side of the block, ... | |
| CHARGING PROBLEM | 8/18/2008 |
| Q: MY '71 AMC GREMLIN 258 HAS A CHARGING ISSUE. THE BATTERY DRAINS TO DEAD OVERNITE. IVE REPLACED THE ... A: Get a good digital multi meter. Hook the Ammeter up in series with the negative post of the battery. ... | |
| 70 amx ignition wiring | 8/17/2008 |
| Q: I am confused with the wiring diagram in the service manual. There are two yellow wires together ... A: Your starter relay has 4 terminals. Two large ones and two smaller ones next to each other. The ... | |
| 327 amc motors | 8/17/2008 |
| Q: will this motor bolt right up to were a 304 or 360 was or does it have different motor mounts the ... A: Yes. The AMC 327 was typical of the engines back in the 50's & early 60's. It is thick wall ... | |
| 76 AMC Pacer | 8/15/2008 |
| Q: I recently was given my grandmothers 1976 Pacer. It has about 70000 miles on it and is in good ... A: Sandra, It sounds as though your Pacer is in need of some carburetor work. If you have to pump the ... | |
| 1960 Rambler American 196 Lhead spark plug wire | 8/11/2008 |
| Q: Do you know the lengths of the original wires and is it possible to get a exact fit set. I have gone ... A: I have had luck at NAPA auto parts stores when finding Rambler ignition parts. Check out your local ... | |
| 1959 Ambassador V8 4 barrel | 8/7/2008 |
| Q: My engine needs nearly 3/4 choke to run well. Engine races up well when you hit pedal at first but ... A: When you reinstalled the intake manifold, did you use sealer around the manifold gasket and properly ... | |
| hesitation | 8/5/2008 |
| Q: I have a 1977 cj-5 and when you push the gas (sometimes) it hesitates as if it's low on gas. Do you ... A: It could be something as simple as adjusting the accelerator pump in your carburetor. Also, possibly ... | |
| 71" 360 sst javelin flexplte/flywheel | 8/2/2008 |
| Q: I have a slight knocking noise when the engine is at idle but disappears when engine revs higher, ... A: I no longer have an interchange manual, but if I remember correctly, the 360 flex plate from 71 on ... | |
| 71 javelin 304 | 7/31/2008 |
| Q: Couple of questions for you. I had my whole engine rebuilt about 4 years ago, it was bored out .030 ... A: 1) .030" over would leave you a bore of 3.780". That makes your engine 309 C.I.D. 2) Where is the ... | |
| 79 CJ 7 master cylinder leaking... | 7/28/2008 |
| Q: I just bought a 79 cj7. My husband took the master cylinder cap off to check the fluid. Now, we have ... A: Is the push rod aadjusted properly? If it too far out, it could prevent the master cylinder from ... | |
| 1972 360 Engine | 7/25/2008 |
| Q: Kevin, Seems like I read some where that the oil pressure/distribution within the engine can be ... A: There is a kit available that includes a 3/8" braided steel line and two 90 degree fittings. It is ... | |
| 88 AMC Eagle that stalls | 7/19/2008 |
| Q: All electrical and fuel lines have been replaced. The car runs good for 5ivve minutes or so than ... A: A few questions: 1) When it stalls, does it imediately restart? Does the engine just crank over? 2) ... | |
| engine swap | 7/13/2008 |
| Q: I have a 1979 AMC Spirit GT with a 304, 4 speed , I think the tranny is a SR4 but not sure. I am ... A: The engine you are installing came with an automatic trans. If you are installing the SR4 on the ... | |
| 78 CJ5 Problems | 7/8/2008 |
| Q: I have a 78 CJ5. About 10 years ago it had an oil leak & my dad & I replaced the rear main. Had to ... A: I don't see a question here, but I think you are asking about the following: 1) Gas Gauge not ... | |
| Engine swap | 7/8/2008 |
| Q: I have a 1964 American that is driving me into bankruptcy. I have spent hundreds of dollars trying ... A: I would recommend checking for a NEW Holley, not rebuilt. I don't trust rebulit carburetors anymore. ... | |
| Engine swap | 7/8/2008 |
| Q: I have a 1964 American that is driving me into bankruptcy. I have spent hundreds of dollars trying ... A: Unless you're a wizard technician & fabricator, forget about the V-6 conversion. It is no easy task ... | |
| Dash lights | 7/6/2008 |
| Q: I can't seem to get the dash lights to work. All the fuses in the fuse block are good and I know ... A: If all of the dash lights are out, it is usually a fuse or the headlight switch. I do not have a ... | |
| 71 AMC Javelin brake conversion | 7/4/2008 |
| Q: Kevin, We are in the process of restoring a 71 Javelin SST. It has manual drum brakes, we want to ... A: For information on front disc brake conversion, go here: http://www.gremlinx.com/discbrake.htm I ... | |
| 65 MARLIN NO BRAKE LIGHTS | 7/4/2008 |
| Q: WORKING ON 65 MARLIN REPLACED MASTER CYLINDER /BRAKE LIGHT SWITCH NOW HAVE NO BRAKE LIGHTS PUT OLD ... A: Do you have power at the switch? If not, check the fuse and wiring. Remove the switch, cover the ... | |
| 350 '75 Nova | 7/1/2008 |
| Q: I recently rebuilt the engine (original 350 with only 400 miles on it so far), in my '75 Nova. It ... A: I am sorry, but my experience is in vehicles manufactured by American Motors Corporation. Your ... | |
| 82 AMC Eagle no start/just click | 2/20/2008 |
| Q: I have a 1982 AMC Eagle that I can't get started. I went out to start it one day and the motor ... A: 1)Short across the solenoid using a jumper cable to see if the starter will crank. 2) make sure ... | |
| Jeep ignition | 2/18/2008 |
| Q: I broke the key off in my ignition, 1986 CJ7. I tried to force it and the bezel broke off too. The ... A: You should be able to buy a complete ignition lock cylinder at a NAPA store. The procedure is more ... | |
| 1965 A.M.C Rambler 440 Could you please help me | 2/17/2008 |
| Q: I have recently purchased a Rambler American 440. It has a 232 six with a blown head gasket. I would ... A: Find a Gremlin, Hornet, or Concord and use the engine from it. Also, snag the front brake calipers, ... | |
| 1964 Rambler 770 Wagon Brakes | 2/17/2008 |
| Q: I recently purchased a 64 rambler 770 and wanted to know how to adjust the brakes. Right now the ... A: Mike, Let me start off by saying if you have a brake problem and you're not that familar with ... | |
| gauges | 2/17/2008 |
| Q: i have a problem with the gauges. the only one that works is my speedometer. the lights for the ... A: Chances are, the CVR (Constant Voltage Regulator) is bad. It's located on the back of the instrument ... | |
| 1978 CJ7 | 2/13/2008 |
| Q: I just purchased a 78 CJ and had a question about the transfer case. It has a 304 auto tranny. There ... A: Your CJ has Quadra-Trac. Basically, it is a conventional 4WD system with the addition of a limited ... | |
| 1977 CJ5 | 2/12/2008 |
| Q: My CJ5 will not start. It has spark to the plugs, and gas going to the carb, but it will not even ... A: 1)Look down the carburetor with the engine OFF with a flashight. Operate the throttle linkage and ... | |
| cj7 ignition | 2/10/2008 |
| Q: my 1984 cj7 (4 cyl) will not start, I know that I got the connector from the distributor pigtail to ... A: Do you have spark? If not, remove the distributor cap and make sure everything is dry and clean. I ... | |
| valve cover | 2/9/2008 |
| Q: on my inline 6 258 4.2 liter, the plastic valve cover leaked so i got an alluminum one. I noticed ... A: AMC/Jeep used metal valve covers for many years prior to installing the plastic one. Condensation ... | |
| carb | 2/9/2008 |
| Q: i want to replace my carb on my inline 6 258 4.2 liter, and you told me i could get a holley 2 ... A: There is available a carburetor adapter for the Holley bolt pattern to a Carter bolt pattern. You ... | |
| power brake and power steering conversion | 2/9/2008 |
| Q: I recently restored an original 1974 CJ-5 Renegade, 304 V8. This particular Jeep came with manual ... A: The safest way to convert is to find a 72-76 CJ and get the components from it. You should be able ... | |
| amc 304 to 360 head swap? | 2/8/2008 |
| Q: I was just wonderin if you would know if amc 360 heads would fit and would I need to change anything ... A: After further investigation, the 360 heads will bolt up to your 304. Use the head gasket for the ... | |
| pushrod removal | 2/6/2008 |
| Q: i have an inline 6 258 4.2 liter, i need to clean pushrods, how exactly do i remove them A: 1) Remove valve cover 2) 1974 & later: Remove rocker arm bridges by loosening each bolt a little at ... | |
| inline 6 258 4.2 liter problems | 2/5/2008 |
| Q: I have a 1983 jeep Cj5, i recently replaced the plastic valve cover with an alluminum one. I have ... A: Pressure testing the radiator would confirm a leaking head gasket, it's the best way to check it. I ... | |
| inline 6 258 4.2 liter problems | 2/5/2008 |
| Q: I have a 1983 jeep Cj5, i recently replaced the plastic valve cover with an alluminum one. I have ... A: 1) I don't think the aluminum cover is the cause. It does sound like coolant is getting into the ... | |
| Gremlin brake problem | 2/5/2008 |
| Q: I have a 1972 Gremlin that I upgraded to front disc brakes and V-8 when I swapped out the front ... A: The disc brake set up should have a combination valve. It does three things: 1) Proportioning valve ... | |
| 1959 Rambler American | 2/2/2008 |
| Q: I'm looking for a newer donor engine and transmission for a 1959 Rambler American Super. Absolutely ... A: I don't know how much work you want to do. You can use a drivetrain from a Gremlin, Hornet, Concord, ... | |
| 327 | 1/30/2008 |
| Q: My wuestion is about the motor, I own a 65 660 classic Rambler wich I was told has a 327 in it.. I ... A: First, the 287 & 327 engines were AMERICAN MOTORS engines and had no parts from a Ford or Chevrolet. ... | |
| Javelin 1969 232 ...Headers.. | 1/24/2008 |
| Q: . I want to install some headers to my Javelin 1969 232, but did not get them where you are or if ... A: Go to this sight: ... | |
| steering play on 69 ambassador | 1/20/2008 |
| Q: The car has 80,000 original miles but there is quite abit of play in steering. can the steering be ... A: Maybe both. Inspect the front suspension for worn components. You can get a little adjustment from ... | |
| 1976 CJ 5 232 C.I. | 1/12/2008 |
| Q: IT STARTS THEN ENGINE DIES DESPITE FOOT ON ACCELERATOR.MECHANIC TESTED ... A: 1) Perform compression test or cylinder leakage test. 2) If you have the original ignition, it is ... | |
| AMC 304 cam | 1/11/2008 |
| Q: I have an AMC 304 out of a CJ5 that I am planning on building up. I want to put a little bigger cam ... A: The original engine components (crank, rods, pistons) are balanced close enough by the factory when ... | |
| AMC 304 cam | 1/10/2008 |
| Q: I have an AMC 304 out of a CJ5 that I am planning on building up. I want to put a little bigger cam ... A: You don't mention what year the engine is, but unless it has 1970 heads, you have plenty of valve ... | |
| 1979 cj-7 transfer case | 1/9/2008 |
| Q: my jeep has a leak at the front end transfer case seal. I have tried all kinds of different sockets ... A: I do not remember the size, however, this vehicle might be invloved in a recall campaign. There was ... | |
| Clutch / Pressure Plate | 1/8/2008 |
| Q: I have an 232 3 spd standard transmisson behind a 304 engine, I need help to figure out the correct ... A: I do not know the number of splines as it varies based on the year & transmission. I can tell you ... | |
| Dying '65 Rambler American, ohv 196 | 1/8/2008 |
| Q: My question is in many parts so take a deep breath before reading. I have had my Rambler for about ... A: 1) by a new or remanufactured distributor. 2)Find a qualified mechanic to adjust the carburetor. If ... | |
| AMC Eagle Sound System | 1/8/2008 |
| Q: I have a 1986 AMC Eagle Station Wagon (all wheel drive) that is in very original condition. I would ... A: Unless you can find an aftermarket stereo that fits the original opening, you have a problem. Most ... | |
| '73 gremlin is sick (not the good kind of sick) | 1/2/2008 |
| Q: my little gremlin is old and tired. it's all he can do to climb long hills, and sometimes he'll ... A: The simplest thing to do is to replace the carburetor. Sounds like yours is in need of an overhaul ... | |
| 74 Javelin Vibration | 1/2/2008 |
| Q: I have a 1974 Javelin, with a 1000 miles on the drivetrain, it has a rebuilt 403 engine and rebuilt ... A: When the engine was rebuilt, were any of the connecting rods, pistons or crankshaft replaced? You ... | |
| gas gauge and sending unit for 1980 cj7 | 1/1/2008 |
| Q: wires go to gas tank cut&to gauge were removed when I bought.Hooked up gauge not working.Reversed ... A: I do not have a wiring diagram for a CJ. You could remove the tank unit, hook up the wire and move ... | |
| 73 Javelin | 12/31/2007 |
| Q: I just read your answer on 304 carb conversion from 2bbl to 4bbl and I like it!!! Does my 73 ... A: Here are some options: Carburetors Holley 0-80457S 600 cfm Edelbrock 1406 600 cfm Headers Edelbrock ... | |
| 73 Javelin | 12/31/2007 |
| Q: I just read your answer on 304 carb conversion from 2bbl to 4bbl and I like it!!! Does my 73 ... A: 1) Holley 600 or Edebrock 650 carburetor with VACUUM secondaries. 2) A set of QUALITY headers, 1 ... | |
| 73 Javelin | 12/31/2007 |
| Q: I just read your answer on 304 carb conversion from 2bbl to 4bbl and I like it!!! Does my 73 ... A: If you have the original engine in your Javelin, you have an EGR valve. It is against the law in ... | |
| 1982 Scrambler continued | 12/29/2007 |
| Q: Just wanted to give you more info regarding my black smoke problem... When I start the Jeep cold - ... A: You bring up a good point of the automatic choke. After the vehicle has been sitting and COLD, look ... | |
| 1982 Jeep Scrambler | 12/29/2007 |
| Q: All my plug are showing normal signs and my cylinders are all running 148-150 compression readings. ... A: These engines have been known to experience worn valve stem seals. Usaully, smoke is emitted right ... | |
| 78 gremlin master cylinder | 12/29/2007 |
| Q: How do I remove the old brake master cylinder to install the new one? Are the nuts on the other side ... A: If you have power brakes, the master cylinder is secured to the booster using nuts. If you do not ... | |
| 69 rambler coil over conversion | 12/26/2007 |
| Q: i found a coil over conversion that says it get rid of the trunnions on ... A: It looks like a coil over conversion, which has become popular with a lot of cars. It replaces the ... | |
| ok im looking to get this '67 Rambler American | 12/24/2007 |
| Q: ok they say it does not run now but it did before. i would like to know what i show do first to get ... A: You need 3 things to get an engine running. 1) Compression. Pull a spark plug and cover the hole ... | |
| 74 Javelin Vibration | 12/20/2007 |
| Q: I have a 1974 Javelin, with a 1000 miles on the drivetrain, it has a rebuilt 403 engine and rebuilt ... A: If you can feel the vibration with the car in Park, it can only be the engine or transmission. You ... | |
| 1978 cj5 not starting | 12/17/2007 |
| Q: I recently purchased a 78 cj5 with inline 6 258 motor for a plow vehicle. it was starting fine but ... A: Usually, a clicking noise indicates an excessive voltage drop in the starter circuit. Low battery ... | |
| 86 cj7 power brakes | 9/17/2007 |
| Q: I just converted my jeep to a power brake system.The pedal feels as it should when not ... A: While running, pull the vaccuum hose from the booster and plug the hose. The brakes should work, but ... | |
| model 20 axles | 9/17/2007 |
| Q: I wanted to put one piece forged axles in my 72 javelin. Is this a good idea? Will axles from a ... A: Find an aftermarket axle specialty company. i.e. Strange. Jeep axles are no stronger that car axles. ... | |
| AMC 360 Heads | 9/15/2007 |
| Q: I'm rebuilding a 360 I have in my 73 CJ5. Would the earlier closed chamber heads give it a boost in ... A: You, my man, have a great head, actually two of them. Very rare. Small chambers (50.6 cc) and large ... | |
| cj7 258 will only run idle | 9/15/2007 |
| Q: my 1979 cj7 ran great until it set in my garage for five months during a total body rebuild without ... A: 1) Check your distributor and see if you're getting spark advance. 2) Did you make all the ... | |
| AMC 360 Heads | 9/15/2007 |
| Q: I'm rebuilding a 360 I have in my 73 CJ5. Would the earlier closed chamber heads give it a boost in ... A: When you say earlier, are you are talking about pre 1970 heads? If so, no. The gains you might get ... | |
| Racing Engine for a 1963 AMC Rambler Classic 660 | 5/3/2007 |
| Q: I just purchased a 1963 Rambler Classic 660 that had been sitting out for quite awhile. I got it ... A: Mike, Usually a fast idle is caused be a sticking choke which in turn causes the fast idle cam to ... | |
| 73amx tach | 4/30/2007 |
| Q: I replaced my gauge cluster with one from my 73 Jav parts car and the tach would not work on either ... A: The 73 repair manual does not give any diagnostics for a tachometer. However, you should be able to ... | |
| 1965 rambler 770 , 327 engine | 4/27/2007 |
| Q: gas in the oil pan am i still looking at fuel pump problems or should i look elsewhere can i take ... A: Bruce, Most older fuel pumps have a hole near the diaphragm in the housing. This allows fuel to leak ... | |
| webber conversion on 82 258 | 4/27/2007 |
| Q: where can i find diagrams of the hoses that i need to keep and the ones i need to plug? The new ... A: Sorry Greg, You're on your own. Some of the vacuum hoses operate emission devices. I don't like ... | |
| 1976 AMC Matador Window | 4/25/2007 |
| Q: While I was using my 1976 AMC Matador the driver's side front window wouldn't go up. This had ... A: Chip, You didn't say if you had a coupe or sedan. Either way, call Collier AMC in Pikeville, NC. ... | |
| amc 5.9 v8 starting problem | 4/23/2007 |
| Q: 9 v8 jeep, when i turn the ignition to start engine the starter engages the ring gear but tries to ... A: I had this problem once. I replaced tha starter with a generic rebuilt unit from Pep Boys. I later ... | |
| Javelin brakes | 4/20/2007 |
| Q: My wife has a 73 Javelin with a 304 V-8 and power drum brakes. I am trying to find the parts to ... A: If your pedal is hard but only an inch away from the floor, it might be time for new brakes. I ... | |
| alternator | 4/20/2007 |
| Q: i purchased an alternator, new battery, and the battery is still draining. how can i test the ... A: If the original regulator did not have the yellow wire, don't worry about it. Often, generic ... | |
| Battery Drain 1977 CJ-5 | 4/20/2007 |
| Q: Kevin I have a 1977 CJ-5 with 232cid motor i have converted over to an hei distributor. my problem ... A: Take a Voltage reading at the battery with the engine running. It should be around 14 Volts. Then ... | |
| alternator | 4/19/2007 |
| Q: i purchased an alternator, new battery, and the battery is still draining. how can i test the ... A: When you say it is draining, I assume you mean the battery dies after the vehicle sits for a while. ... | |
| 1963 AMC Rambler Classic 550 | 4/18/2007 |
| Q: Kevin, I ended up with the above car, and my son and I would like to put a decent, readily ... A: Either 232 or 258 will work, but the question should be "how much money and time do you have?". It ... | |
| Gauges | 3/29/2007 |
| Q: The fuel and temp gauges on the dash read high constantly. The previous owner bypassed this system ... A: It's called a CVR, constant voltage regulator. It is wired in the circuit board. It reduces voltage ... | |
| 1966 amc rambler classic | 3/18/2007 |
| Q: I need a clutch cable for my '66 Rambler Classic but I am have zero luck in finding one. However, I ... A: Jodi, Here is a web sight I recommend for finding a clutch cable. ... | |
| brake booster for 72' Javelin | 3/15/2007 |
| Q: My 72' Javelin has manual disc (front) drums back. It brakes good except for the pedal pressure ... A: You should be able to bolt up a booster to your Javelin and use the same master cylinder. Be sure to ... | |
| Driveline | 3/11/2007 |
| Q: 1959 Rambler American. I had drive line rebuilt for common u-joints. Is there a trick to getting ... A: Rhonda, I am assuming you are talking about the nut on the differential pinion. First, clean the ... | |
| alternator/battery/radiator | 3/8/2007 |
| Q: Well i founf out that the brand new battery that i bougth it was bad it wasnt holding any charge so ... A: It is possible that your wiper motor or pump might be worn out. Run a vacuum line directly from the ... | |
| alternator/battery/radiator | 3/8/2007 |
| Q: how can you tell if it is a alternator or a generator?i have a 1960 rambler american super. the ... A: A generator is a long round black component driven by the fan belt. An alternator is smaller and ... | |
| alternator/battery/radiator | 3/8/2007 |
| Q: i have a 1960 rambler american super. the battery is brand new and i realize that there is no cable ... A: Ernesto, Are you sure your car has an alternator? A 1960 American originally came with a generator. ... | |
| jeep engine swap | 2/13/2007 |
| Q: I have a 1980 CJ7 with a T176 and a 1974 304 from a Javelin. I need a manual flywheel and am having ... A: Jon, The 304 flywheel off Ebay will work, as will your clutch and starter. Be sure you get the ... | |
| A.M.C. Cars. Are they VERY easy to repair? | 2/9/2007 |
| Q: I read you instructions and IT says to ask about AMC cars. It could be that you might be able to ... A: The question you ask is very subjective. I think AMC vehicles are easy to work on. But I have worked ... | |
| engine date code on 78 CJ7 304 | 1/31/2007 |
| Q: I recently purchased a 1978 CJ7 with a 304 V8. I have been having problems finding parts to fit for ... A: Patrick, Sorry for the late reply. I was unable to find my literature that has the engine date ... | |
| oil pressure sensor and gauge | 1/26/2007 |
| Q: I have an '85 CJ7, with an '83 AMC 360 engine. Lots of horsepower and torque and all that. But... I ... A: Kirk, I believe your CJ came with an electronic oil pressure gauge. If not, you can purchase one ... | |
| 1966 Rambler Classic | 1/13/2007 |
| Q: Hey, I have a '66 Rambler Classic 770, and there is a lot wrong with the engine. I've got quite a ... A: Taylor, As the saying goes, how much money do you want to spend? You can have a V-8 installed, but ... | |
| I can't remove the old ignition coil | 1/10/2007 |
| Q: A 1987 AMC EagleI am unable to get the old ignition coil out. I loosened the back screw but it won't ... A: Brian, I am assuming it is difficult to remove because of rust. Try a can of rust penetrant or ... | |
| 85 cj7 258, stumbling, cutting out, on load | 1/8/2007 |
| Q: Kevin, Hi I have a 85' 258 with the carter bbd, just rebuilt to specs. I have been trying to ... A: Randy, A couple ideas. 1) Have you checked the fuel pressure? Low fuel pressure and volume can ... | |
| 304/360 Cylinder Heads | 1/8/2007 |
| Q: what I failed to include is that I have a HEI GM ignition system, along with headers and an ... A: Installing late model 360 heads would increase the air flow in and out of the engine, due to the ... | |
| loud, tinny noise | 1/7/2007 |
| Q: There are no Jeep experts on All Experts, so I chose you. Here's the deal...1989 Jeep Cherokee six ... A: Dick, I would suggest going down to your local auto parts store and purchasing an automotive ... | |
| 304/360 Cylinder Heads | 1/6/2007 |
| Q: I have a 73 304 CJ5. It is worthwhile swapping 304 heads for 360 heads? Else, would flat head ... A: Jack, If all you have done is install TBI, I wouldn't put 360 heads on it. If you were going to ... | |
| AM postal truck circa 1984 | 1/5/2007 |
| Q: I am in Britain and trying to find information on the strange square line half ton postal van ... A: Stephen, Sorry, but I do not know anything about AM General vehicles. I was, however, able to find a ... | |
| transmission | 1/4/2007 |
| Q: I've got an amc 360, t5 tranny and dana 300 transfer case in my cj7. Is there an automatic ... A: Lane, A transmission from any V-8 Jeep will bolt up to the engine, I do not know about your transfer ... | |
| AM General postal van | 1/2/2007 |
| Q: I have a 1974 AM General postal van with a 232 AMC engine and a Borg-Warner 12 automatic ... A: Robert, The only information I have is for a 232 with a Chrysler Torque-Flight trans. I thought ... | |
| 84 CJ-7 258/6cyl | 12/31/2006 |
| Q: Kevin, I have read some of your postings and found them very informative. The question I have is ... A: Vince, Though I have never installed a Motorcraft 2100 on a 258 AMC engine, I have rebuilt MANY of ... | |
| 69 AMX Disc Conversion | 12/29/2006 |
| Q: I have a 69 AMX, 434 4 spd, manual drum brakes, and I purchased a set of spindles, rotors and ... A: Dean, They should work. Spindles, calipers and rotors should bolt up. Use a master cylinder & ... | |
| BRAKE conversion | 12/29/2006 |
| Q: I have 1986 CJ-7 with manual brakes and i am wanting to install power brakes. What is out there that ... A: Jared, Instead of installing a used power brake booster, I would recommend purchacing a reman or ... | |
| power brake conversion | 12/26/2006 |
| Q: I just picked up a 1965 American 440. Want to know if I can slap on a power booster and perhaps ... A: You can add power brakes by using a booster/master cylinder from another AMC that will fit. Try a ... | |
| 83 Eagle 4x4 clicks. | 11/15/2006 |
| Q: Hey Kevin, I was backing up to park my car, and the front, driver side wheel assembly fell off and ... A: Ben, This message suddenly popped up in my email. It looks a bit old, but I'll try to answer, ... | |
| Jeep 304 starts intermittently | 11/5/2006 |
| Q: I have a 77 304 in my jeep with 260,00 miles on the engine. Engine ran great until August then ... A: Wayne, Here's a few ideas for you: 1) Inspect cap and rotor for cracks or carbon tracks. I know ... | |
| Brake Diagnosis 77 cj7 | 11/4/2006 |
| Q: Kevin, I just purchased a cj7 on ebay and having purchased and owned another years ago, also ... A: Lonnie, Good idea to go after the brakes. Does the brake pedal come up if you pump it? It should. ... | |
| cj5 blues | 11/3/2006 |
| Q: Kevin, here's an update. I heard that the problems I was having could have something to do with the ... A: Jim, I see, snuck an external ballast resistor in on me, eh? The external resistor is not from the ... | |
| '62 Rambler Classic | 11/2/2006 |
| Q: Will a '62 cast iron 196 engine originally installed in a car with a three speed manual trans fit in ... A: Don, If the Borg Warner is from an 61 Rambler, there should be no problem. You will also need a flex ... | |
| 61 Rambler Classic | 11/1/2006 |
| Q: I'm the guy who asked about putting a V8 in my 61 Rambler ......... Anyway, my mechanic says the ... A: John, Your 360 needs only three things to run, providing they happen at the right time. 1) Strong ... | |
| cj5 blues | 11/1/2006 |
| Q: Kevin, thanks for your recommendations on a new coil and wires; I'm confident that will solve the ... A: Jim, Ignition modules are much like other electronic components, they can be temperature sensitive ... | |
| cj5 misfire at cruise | 11/1/2006 |
| Q: I have a 79 cj5 with an amc 360 and motorcraft distributor. that intermittently misfires ... A: Jim, I wouldn't worry about the little vertical free play inside your distributor. Two items that ... | |
| Engine Power in the old days | 10/30/2006 |
| Q: Sorry, about this one more question, and what about horsepower! For example your car had how many ... A: Sorry about that, High performance engines were rated by their manufactuers between 360 - 435 h.p. ... | |
| Engine Power in the old days | 10/30/2006 |
| Q: this last weekend a friend of mine and I were talking about the american v8's and a question ... A: Antonio, American V-8 engines from the 60's & 70' ranged from 4.2L to over 7.3L, or more common ... | |
| 65 Ambassador | 10/27/2006 |
| Q: Good Day, My car has a 6cyl. engine 2spd. automatic trans. I want to put a 1976 360V8 and a 3spd.in ... A: Gary, Sorry about that, they deleted the first part of my message. Let's try again. You can replace ... | |
| starting problem CJ7 | 10/27/2006 |
| Q: it's funny - someone asked you a question a while back...(27th June of this year) and I'm getting ... A: Nick, I would recommend replacing the starter solenoid and thouroughly clean all cabe ends. It's not ... | |
| 1971 owa-4 carb | 10/26/2006 |
| Q: I have a 1971 javelin SST 360. Was originally a 304 but replaced somewhere down the line by a ... A: Brain, If it is a 1970 or later AMC engine, it should have come with a Motorcraft carburetor. Not a ... | |
| amc engine swap | 10/25/2006 |
| Q: I have a 1961 AMC Rambler Classic with a 196.5 and auto trans, I would like to replace the engine ... A: John, Technically, you could install most any V-8 engine. The question is, though, how much do you ... | |
| oil gallery plugs | 10/25/2006 |
| Q: I'm having trouble with oil pressure in a rebuild. Is there a way to check the oil gallery plugs to ... A: Dale, When you did the rebuild, did you remove all the gallery plugs? If you left one loose on the ... | |
| CJ7 4cyl AMC won't start | 10/25/2006 |
| Q: .) Kevin, The year of jeep is 1984, AMC 4cyl engine Thanks again Have a nice day. RaphaëlHello of ... A: My experience with Jeeps is limited to 1979 and earlier. Your 1984 has more electronics, such as an ... | |
| 1984 Jeep Cj-7 Proportioning Valve Removal | 10/24/2006 |
| Q: Question How does one remove the proportioning valve on an '84 Jeep CJ-7? Answer Henry, If you are ... A: Henry, If you can get to the nuts inside the frame, use a pair of vise grips to hold them. If you ... | |
| 1984 Jeep Cj-7 Proportioning Valve Removal | 10/23/2006 |
| Q: How does one remove the proportioning valve on an '84 Jeep CJ-7? A: Henry, If you are just removing it, remove the brake lines, then remove the bolts that secure it to ... | |
| Which rear end in '77 Gremlin? | 10/22/2006 |
| Q: Kevin, My friend recently purchased a '77 Gremlin, 232 six, automatic trans. We were trying to ... A: Jeff, There are only 2 rear ends that came in a Gremlin. AMC identifies their rear ends by the ring ... | |
| engine/transmission connection bolts | 10/20/2006 |
| Q: I have a 1959 amc rambler (6 straight engine) now we are almost finished rebuilding the car and have ... A: Aad, Here is a websight that lists various AMC parts vendors. Please send them an email and they can ... | |
| bad brake pressure | 10/18/2006 |
| Q: i have a frame off 1976 cj7 complete new brake system i changed the proportion valve to a disc drum ... A: Sorry for the late reply, I've been out of town on business. Could the lines at your master cylinder ... | |
| 69 rambler brakes | 10/17/2006 |
| Q: I have a 69 rambler and want to put disc brakes on it.I use it for drag racing and street ... A: Mark, Actually, front drum brakes are better than disc for drag racing. On a disc brake system, the ... | |
| Electrical in Dash | 10/14/2006 |
| Q: Kevin I have a 1985 AMC CJ7 which I am slowly attemtping to restore. I was working on the radio ... A: No. A bad fuel gauge should not cause the engine not to start. I would check for a blown fusible ... | |
| starter motors | 10/12/2006 |
| Q: Kevin, this is a general question on starter motors. Key will not activate starter motor but if the ... A: Actually, it sounds more like you might need a solenoid. You can get them as an assembly if you buy ... | |
| 1961 Rambler Fuel Pump | 10/11/2006 |
| Q: I'm restoring a 1961 Rambler Classic with the alum.block 6 cyl engine. It has vacuum wipers with ... A: If my memory serves me, one of the lines run to the wiper motor, the other to manifold vaccuum. I do ... | |
| cj-7 with weber carburetor | 10/1/2006 |
| Q: I recently purchased a 2bbl weber carb for my 81 cj-7 with a 258 six. The jeep runs good until the ... A: Sam, I do not have any experience with a Weber carburetor. It is possible that there is a problem ... | |
| '69 Rambler performance brakes | 9/30/2006 |
| Q: I've seen that you can do a disk front conversion using stock parts, but I'm looking to do a REALLY ... A: Adam, I don't know if I would install the type of brake you are looking for on your stock spindles. ... | |
| Engine Identification | 9/26/2006 |
| Q: I have a 1976 CJ5 with a V-8 engine and 2bbl carb. I suspect it is not the stock engine. The ... A: Aaron, According to the VIN, you have a 258 6 cylinder engine. Hmmm If you have an AMC V-8, you can ... | |
| amc eagle 4.2L 254 straight 6, sputters when i hit the gas. | 9/21/2006 |
| Q: Kevin, thanks muchos. I decided, after posting, to go take a look under the hood (about 3am working ... A: Glad you were able to locate the problem. When sitting here on my computer trying to assist on ... | |
| 1979 Jeep CJ 7 Won't Start | 9/20/2006 |
| Q: I have a 1979 Jeep CJ 7, V-8 304. I run a dual battery system and yesterday drove to lunch and ... A: Mark, Sorry,I do not have a wiring diagram for your Jeep to help you with your ignition wiring. ... | |
| headlights on = huge voltmeter drop | 9/20/2006 |
| Q: I just rebuilt the motor (258) in a 1977 Jeep CJ7 and cleaned up the underhood wiring (clue?). Now ... A: Matt, I hope you have a Voltmeter and know how to use it. You need to do a "Voltage Drop". With the ... | |
| amc eagle 4.2L 254 straight 6, sputters when i hit the gas. | 9/19/2006 |
| Q: My eagle runs a 4.2L 254 straight 6. Its always had issues with timing, and it leaks oil into the ... A: Ben, It sounds like the acceleration circuit of your carburetor has a problem. With the engine NOT ... | |
| bad wheel cylinder? Proportioning valve? | 9/18/2006 |
| Q: I have a 1972 AMX and I replaced the driver's rear wheel cylinder. When bleeding the brakes fluid ... A: Remy, Sorry for the late response, I just returned from out of town. Let me take a quote from the ... | |
| parts | 9/17/2006 |
| Q: Answer - On 2 wheel drive vehicles such as yours they are not referred to as "front axles", they ... A: You can remove the complete rear axle assembly and replace it with one form a Hornet, Gremlin, ... | |
| AMC 360, Jeep pick-up, horsepower/torque | 9/15/2006 |
| Q: Repairing an '85 Jeep j-20 pick-up. Had a broken piston & compression ring. Anyway, looking for ... A: Jeff, Got some ideas for you. 1) a good 3 angle valve job would help. 2) go to www.compcams.com and ... | |
| parts | 9/14/2006 |
| Q: The only reason I rated you as a 5 in knowledge is because you should know that the axle holds the ... A: On 2 wheel drive vehicles such as yours they are not referred to as "front axles", they are called ... | |
| parts | 9/14/2006 |
| Q: No, it is only rear wheel drive. I just want to upgrade the rear end with a model 20; however I read ... A: Please go back to my first answer. Your AMC 20 differential is strong enough for your 258 six ... | |
| amc engines | 9/11/2006 |
| Q: what is the diference between a 304 and a 360.is it bore and stroke or is ther external ... A: Ben, The difference between a 304 and a 360 is it's bore. The bore of a 304 is 3.75"; the 360 is ... | |
| parts | 9/11/2006 |
| Q: I have a 78 Concord, 258 2bbl. 904A; 2 door liftback. I have some questions: 1) I want to have a ... A: Jason, You state that your Concord has a front and rear axle. Concords are 2 wheel drive and only ... | |
| charge problems | 9/6/2006 |
| Q: I have a 1979 cj7 that i am currently restoring and am having difficulty with the wiring. I am still ... A: Justin, I would suggest having your charging system tested by a shop using a Volt/Amp meter. It ... | |
| 1977 CJ5 w/304 - pulleys don't align | 9/6/2006 |
| Q: This CJ5 had no smog parts and had aftermarket speed parts on it. To pass smog in Cali. the stock ... A: Tom, You should try and locate a shop manual for your CJ5. It will have the belt configuration and ... | |
| Voltmeter | 9/4/2006 |
| Q: Kevin! THANK YOU FOR THE QUICK RESPONSE! Yeah right now my voltmeter is hooked up with the power ... A: Kris, A Voltmeter requires only two wires. A wire running from the battery positvive to the meter, ... | |
| Voltmeter | 9/4/2006 |
| Q: I have a 1973 AMC Gremlin X. My problem is my voltmeter guage reads 12volts with the car not ... A: Kris, A Voltmeter is NOT connected the same way as an Ammeter. A Voltmeter is hooked in parellel, an ... | |
| SC/Rambler | 9/3/2006 |
| Q: I am looking to find out the history for my 69 SC/Rambler, and I'd like to know when it came along ... A: Jon, Unfortuantely, AMC VIN's do not provide production date information. There is, however, a plate ... | |
| Vapor Lock ? | 8/31/2006 |
| Q: I have a 1990 Buick Century with a 3300 v6 motor . i will drive about 25 miles and when i go to ... A: I am sorry Mike, I know nothing about Buicks, especially the later model ones. I answer questions ... | |
| CJ7 starting issues | 8/28/2006 |
| Q: My Jeep usually runs great and starts without a problem. I have not driven in a while and got in it ... A: Bryan, If you have a voltmeter and know how to use it, GREAT!. You need to do some Voltage Drop ... | |
| 64 rambler disc brake conversion | 8/27/2006 |
| Q: I recently purchased a 64 AM rambler and need to know if there is a donor car optimal for converting ... A: Steven, Because of the 64 having upper trunnions instead of conventional ball joints, your best ... | |
| 61 rambler follow up | 8/20/2006 |
| Q: Ok I may have spoke to soon because now Im having the same problem with the car not holding a ... A: Michelle, If your regulator is adjustable, you might need to adjust it. It requires a Voltmeter and ... | |
| starter motor problem | 8/20/2006 |
| Q: my starter motor disengages before the engine starts and make a funny noise when doing so A: Paul, You didn't say what kind of vehicle you have. It does sound, however, that the starter bendix ... | |
| 61 rambler generator | 8/19/2006 |
| Q: I recently replaced my voltage regulator and had my generator rebuilt due to both not working ... A: You say the generator is working fine. How are you checking it and what results do you come up with? ... | |
| Help with a 1966 AMC Marlin Trunk | 8/18/2006 |
| Q: The trunk on my 66 Marlin hasn't been opened in about 4+ years, because the lock is missing. You ... A: Robert, I'll be honest, I have never had to break into a 66 Marlin trunk. However, most of the time, ... | |
| brake proportioning valve | 8/18/2006 |
| Q: Followup To Question - Hi Kevin, I've done much reading about the brake light that goes on in my ... A: Your symptoms could be caused be a defective proportioning valve,or if the brake shoes are ... | |
| brake proportioning valve | 8/17/2006 |
| Q: I've done much reading about the brake light that goes on in my '68 AMX, but I don't undertstand why ... A: Steve, That is the proportioning valve. It is found on vehicles with front disc brakes. The ... | |
| Question about a 1966 AMC Marlin | 8/16/2006 |
| Q: I just purchased a 1966 AMC Marlin with a 327 V8, 4bbl carb, and a 4 speed with the console, and I ... A: Robert, I do not know how many 66 Marlin with 4 speeds were produced. There might be a book listing ... | |
| brake proportioning valve | 8/14/2006 |
| Q: I've done much reading about the brake light that goes on in my '68 AMX, but I don't undertstand why ... A: Steve, The valve below the heater motor is the pressure differential switch. If you remove the wire ... | |
| transmission swap | 8/12/2006 |
| Q: I recently aquired a 304 1972 javelin sst, automatic trans. I found out that although the trans. ... A: Jay, To install a manual transmission in your Javelin would require a number of different ... | |
| 1968 Ambassador 343 carburetor question | 8/9/2006 |
| Q: I have just purchased a 1968 Ambassador DPL four door equipped with a 343 and four barrel carb. The ... A: Doug, Your AMC has a Carter AFB carburetor. It was a very popular carburetor back in its day. ... | |
| addendum to cam gear question | 8/8/2006 |
| Q: Original question-Should the timing marks be aligned side by side on inside or on the outside of cam ... A: Brad, On a 258, the timing marks on the cam gear are facing the outside of the gear, at least on ... | |
| best carburetor for 72 javelin | 8/8/2006 |
| Q: I recently aquired a 1972 304 AMC javelin. It currently has a 2bbl carburetor. I want to upgrade ... A: Jay, If you have a stock 304 or 360 V-8, I would recommend a 600 cfm carburetor with vaccuum ... | |
| '69 AMC Rambler Rogue Eccentric kit of wiper assembly | 8/5/2006 |
| Q: My brother-in-law has a '69 Rambler Rogue (he's in Canada). He needs an eccentric kit for his ... A: Paul There are a number of AMC vnedors who might be able to help you out. Here are a few: Collier ... | |
| !957 Rambler | 7/30/2006 |
| Q: Any idea where I could find Hood Hinges for this car, Did Nash /amc make it's own hood hinge, is it ... A: Brain, Nash made their own body parts. Here's a few places for you to call that specialize in used ... | |
| 86 Jeep CJ7 | 7/29/2006 |
| Q: here is follow-up question. Thanks your suggestions were a big help, engine now running. Been ... A: John, Sounds like you need to overhaul your carburetor, or have it done. Another option would be to ... | |
| brakes | 7/26/2006 |
| Q: I have a 1963 AMC Rambler American station wagon 220 that has brake drums all around. I am looking ... A: William, The problem with all AMC cars prior to 1970 is they do not have an upper ball joint. They ... | |
| Sundancer | 7/21/2006 |
| Q: Do you have any idea how many AMC Concord Sundancers (-82) were made by griffith co.? Here is a pic ... A: Aki, I have seen a few AMC Concord and Eagle Sundancers, but I do not know how many were ... | |
| 1985 Jeep CJ-7 starting | 7/18/2006 |
| Q: I am writing you for the second time. First I would like to say thank you for your last response! ... A: At this point, I would recommend bringing it to your local mechanic. The module could be bad, but so ... | |
| 1966 AMC Marlin | 7/18/2006 |
| Q: The engine and radiator has been redone totally, while cruising, the temperature is about half or ... A: Here are a few things to check: 1) Are you using a 160 or 180 degree thermostat? 2) Is the water ... | |
| '68 AMX PS Pump | 7/12/2006 |
| Q: Do I need any special tools to disassemble and "re-neoprene" part of the PS pump. I believe that I ... A: Steve, You should be able to remove the pump assembly and replace the "O" rings without a special ... | |
| 1979 cj7 4.2l auto- not firing | 7/11/2006 |
| Q: bit on the cusp of 1979 limits! i've got a 1979 cj7 that was working fine starting etc until onday ... A: George, Using a test light, turn the key to the run position. You should have power to the (+) side ... | |
| old gaskets | 7/9/2006 |
| Q: Having trouble getting the old gaskets off the intake any tips on removing them I would appreciate ... A: Stan, Providing you have a cast iron manifold, there are a couple things you can try. 1) A rotory ... | |
| Build Sheets | 7/8/2006 |
| Q: I have a 73 AMX and found the build sheet under the carpet. It has lots of codes on it and many ... A: Mark, I have not seen a build sheet since 1979. I do not have the codes. However, pleae look at this ... | |
| 1978 cj 7 brakes | 7/7/2006 |
| Q: found out that rear was not working, i got them free and was working ok then the fronts started ... A: It sounds like you might have a problem with your master cylinder. There is a push rod between the ... | |
| AMC Eagles | 7/6/2006 |
| Q: I just purchased an '83 SX-4 Eagle that has an ignition problem. The engine will start all right, ... A: Try disconnecting the tach wire from the coil. If the condition still exsists, the tach is probably ... | |
| oil pressure | 7/5/2006 |
| Q: I know that AMC engines have trouble with their oil pressure, but i swapped a 360 into my cj instead ... A: When the oil pressure drops 1) what does it drop too? and 2) does the engine start to knock? What ... | |
| amc transmission | 7/4/2006 |
| Q: Do you know if the output shaft and transfer case adapter on an AMC 727 torqueflite would bolt up to ... A: You got me there. I have not had a transfer case/transmission out for many years. There were a ... | |
| 1985 Jeep CJ-7 starting | 7/3/2006 |
| Q: I have owned my CJ-7 for 13 years and know all the starting problems with these jeeps! I have ... A: Sorry about the short response. I hit the send button before going into detail. It has been my ... | |
| 66 rambler american 220 | 7/2/2006 |
| Q: I have a 66 american 6cyl 199ci bw m-36 auto trans no power steering, no power brakes, no radio ... A: AS they say down here, You sure got a heap of questions! 1) Use a fuel pump from another AMC 6 ... | |
| Starting Problem Jeep CJ7 | 6/27/2006 |
| Q: My 1986 Jeep CJ-7 will not start. I drove it to the beach, with no problems and then an hour later ... A: A simple test is to turn on your headlights; then crank the engine. The lights should dim VERY ... | |
| alternator | 6/26/2006 |
| Q: have a 1967 american 440 wagon,232 six,automatic bought a one wire alternator not sure what wires to ... A: If your AMC came with a Motorola alternator, the wires should be: Green, Orange, Red, & Black. ... | |
| 86 Jeep CJ7 | 6/21/2006 |
| Q: wanted a summer project, friend gave(no $) me an 86 CJ7, engine(6-258) hadn't been started in over a ... A: 1) Try changing the oil & filter. Being that the oil pump is driven by the distributor, remove the ... | |
| 84 CJ7 258-6 Starting Problem | 6/16/2006 |
| Q: When I turn the key to "start" the engine turns over and runs untill I place the key to "Run" and ... A: I don't have much experience on the newer AMC/Jeeps with an ECU. However, I would recommend ... | |
| specs | 6/15/2006 |
| Q: Can you give me the number or specs on the transmission, transfer case and differentials for a 1987 ... A: I don't have information on that new of a vehicle. I go up to the late 70's. The engine is basically ... | |
| engine stalling on pick up | 6/14/2006 |
| Q: many thanks for your previoous answer to this question. Since then i have had the car checked and ... A: You would have to replace the fuel pump as an assembly. It cannot be rebuilt. You should be able to ... | |
| Disc brake issues | 6/14/2006 |
| Q: I have re bled the brakes, pulled the valve out .060,removed the valve switch, and the bled each ... A: What master cylinder are you using? Did it come from a vehicle with 4 wheel drum brakes? If so, ... | |
| fuel gauge | 6/14/2006 |
| Q: I have a 1976 Matador that I have been restoring. I can't seem to get the gas gauge to work. I've ... A: I need more info. Disconnect the wire at the fuel tank sender and ground it. Turn on the ignition ... | |
| Disc brake conversion | 6/13/2006 |
| Q: The complete brake system of the 82 spirit, spindles, hubs, discs, rotors, dust sheild,etc I checked ... A: Did your AMX have a single diaphragm booster? In the original single diaphragm set up, the rod ... | |
| Disc brake conversion | 6/13/2006 |
| Q: I have a 68 AMX that had the 4 piston calipers from the factory on it, I replaced those with a set ... A: I would try and find a proportioning valve assembly from a Concord or Spirit. Did you replace the ... | |
| 1995 Jeep wrangler instrument cluster | 6/11/2006 |
| Q: The small bulbs on my speedomoter and tacometer went out and I have removed the instrument cluster ... A: I am not familier with the later model Jeeps. However, if you have the cluster and the bulbs ... | |
| POOR OIL FLOW,BURNT 2 LIFTERS | 6/9/2006 |
| Q: I HAVE A 360 THAT I PUT IN TO A 84 WAG IT WAS A REMAN MOTOR.THE MOTOR RAN GREAT FOR ABOUT 6 MONTHS ... A: I would recommend hooking up a mechanical oil pressure gauge and monitor the oil pressure. The weak ... | |
| 1968 rebel vaccum wiper | 6/9/2006 |
| Q: my vaccum wiper motor works but has no power to complete a full cycle. How can i repair or find ... A: The best thing to do is to convert to electric wipers. However, if you would rather stick with the ... | |
| AMC 303 Carb | 6/2/2006 |
| Q: I have an AMC 304 stock in a CJ5. right now I have a Holly 2bl 500cfm carb and want to put on a ... A: If you have been using the Holley 500 with no problem, the Motorcraft should be OK. If possible, ... | |
| O2 Sensor | 5/31/2006 |
| Q: check engine light on, parts store received code, advised me that the O2 sensor heater circuit ... A: The catagory I vollenteer for is American Motors. That includes vehicles manufactured by American ... | |
| O2 sensor circuit low voltage | 5/24/2006 |
| Q: My check engine light came on two weeks ago and the computer said it was code P0171(system to ... A: Joe, Worn spark plugs and a loose radiator cap will not set a P0137 code. There are other areas that ... | |
| O2 sensor circuit low voltage | 5/23/2006 |
| Q: My check engine light came on two weeks ago and the computer said it was code P0171(system to ... A: Though my specialty is vehicles manufactured by American Motors Corporation prior to 1981, (pre OBD ... | |
| Oil Change | 5/17/2006 |
| Q: Can I Change oil without using a new filter? WHat is the best oil and filter to use? I have a 1967 ... A: Yes you can....but why whould you want to? When you change your oil, but not the filter, you leave 1 ... | |
| Fuel problems 1966 Rambler American 440 | 5/11/2006 |
| Q: I am helping a friend restore a 1966 Rambler American 440 with a 6 cylinder automatic transmisson. ... A: You can locate a carburetor at www.napaonline.com or your local NAPA auto parts store. They also ... | |
| hurst comp/plus 4spd amc | 5/10/2006 |
| Q: I have a 71 jav sst 401 4spd/t-10. I am trying to put the orig. hurst shifter back in as it was ... A: I'm dusting the cobwebs off in my memory banks, but on 1970-1974 AMC T-10 transmissions with a Hurst ... | |
| 65 marlin,gauges | 5/10/2006 |
| Q: MY NAME IS PAT OHERN. I LIVE IN HARTFORD CITY,INDIANA. LAST AUGUST I PURCHASED A 1965 MARLIN WITH ... A: I can think of tow things to check. 1) CVR (contstant voltage regulator) 2) short in circuit. Try ... | |
| Disk Brake Changeover | 5/9/2006 |
| Q: I have a 74 gremlin with drum brakes and want to change over to disc brakes. I got a disc brake ... A: If the blueish color is located on the spindle directly where the inner or out wheel bearing is ... | |
| brakes\steering\ 258 6 cyl. | 4/29/2006 |
| Q: What disc brake set up and power steering system will fit my 66 american? Will a 258 six with mopar ... A: Because your American has the old design trunnions instead of ball joints, you are limited to using ... | |
| AMC brakes | 4/20/2006 |
| Q: I have a '69 Javelin SST, 343 CID, auto with drum brakes. I cannot keep rear brakes on it. I can ... A: What do you mean when you say cannot keep rear brakes on it? Do the rear brakes not apply? Do they ... | |
| pack rat ! | 4/15/2006 |
| Q: I do not use my vehicle everyday so I thought I'd aske you the following - maybe you will have an ... A: You really won't know if any wiring or other hidden damage has occured until you least expect it. ... | |
| amc 360 bucking and cutting out at highway speed | 4/5/2006 |
| Q: I have a 79 cj5 with a remanufactured amc 360 by Jasper engines. I've noticed that everytime I ... A: It could be a number of things, but here are some areas to check that can contribute to the ... | |
| Crank Pulley | 4/5/2006 |
| Q: I replaced the AMC 360 engine in my 81 jeep with a 401 engine out of what I believe was a 71 Jav. ... A: This is a good one. I have not experienced this condition so give me some time to dig up an answer ... | |
| Faulty windshield washer switch | 4/4/2006 |
| Q: I have a 1982 AMC Concord DL, the wiper switch works for the wipers, but I can,t activate the ... A: 1) disconnect the negative battery cable 2) place a shop rag or towel over the steering column 3) ... | |
| 4.0l 727 | 4/3/2006 |
| Q: I am building a jeep comache pick up truck for the drag strip. I would like to put a 727 in it, I ... A: AMC used the 727 since 1972 in their cars, too. Vehicles with a 360 or 401 had the 727 trans. Being ... | |
| automatic - brakes | 3/22/2006 |
| Q: Kevin, I drive an automatic and sometimes, on gentle slopes, let the car just roll in neutral before ... A: No chastising, I'm not Click & Clack on NPR. Technically speaking, placing the automatic ... | |
| Door lock actuator | 3/16/2006 |
| Q: My car is not american made (BMW) but the question is generic. I have power locks and the front ... A: I apologize, but I do not have any experience with BMW's power door locks. The vehicles I have ... | |
| hi i ahve a 1992 v6 i... | 3/9/2006 |
| Q: i ahve a 1992 v6 i think buick century and i charge it and it does not seem able to hold a charge ... A: My category is American Motors, which means vehicles manufactured by American Motors Corporation. ... | |
| Diff. 3.54 & Shifter Hurst | 3/7/2006 |
| Q: I am the owner of a 68 AMX 4 speeds with a 343 engine. I want to change my 3.15 diff for a 3.54 ... A: As long as the ring and pinion gears are from a V-8 AMC, it will work. You will need to use a new ... | |
| Buick Lasaber interior lights won't go off | 1/3/2006 |
| Q: My interior lights will not go off as long as the engine is running. I have it at a local garage now ... A: I am sorry. I do not know anything about Buicks. I do not have any wiring diagrams or manuals. My ... | |
| blower motor | 1/3/2006 |
| Q: my heater does not blow,,,i replaced the blower motor,and it still does not blow,,i took it back ... A: It sounds like the fan blade or "squirrel cage" will need to be replaced. It is probably made of ... | |
| water drain | 12/30/2005 |
| Q: nice to see amc guys out there, ever see any amc's being assembled on the line?.love the javelins, i ... A: I toured the Kenosha plant while working for AMC. I also have an old book titled "What happens in a ... | |
| Auto transmission problem | 12/29/2005 |
| Q: I realize my problem isn't specific to your experience. But it is a general automatic transmission ... A: My experience is with Toyota's computer controlled transmissions. You could try disconnecting the ... | |
| Auto transmission problem | 12/29/2005 |
| Q: I realize my problem isn't specific to your experience. But it is a general automatic transmission ... A: I do not have any experience with Eagle Summits. However if the transmission is computer controlled ... | |
| 1998 buick regal motor seized? | 12/27/2005 |
| Q: We have a 1998 buick regal 3800 V6 25th anniversary sedan with around 140K miles. Car won't start, ... A: My expert category is "Vehicles manufactured by American Motors Corporation" I know very little ... | |
| fan belts | 12/21/2005 |
| Q: i have an 86 buick regal 3.8L I need the fan, alt, ac belt and there is also another belt next to it ... A: I am the expert in the American Motors category. This includes vehicles made by American Motors ... | |
| kia timming marks | 12/20/2005 |
| Q: I need to the setting for 1998 kia sportage timming marks on the crank & cams. A: Sorry, I am an expert on vehicles manufactured by American Motors Corporation. They went out of ... | |
| diesel | 12/18/2005 |
| Q: why do diesel injector pipes have to be the same length A: I specialize in vehicles produced by American Motors Corporartion. This company has been out of ... | |
| Production figures | 12/14/2005 |
| Q: How many 1967 Rambler American 290 V8 440 Hardtop Coupes were produced? A: You got me there. The only production figure I can find is for total AMC vehicle production in 1967 ... | |
| no start | 11/30/2005 |
| Q: I have a 1988 Eagle with a V-8,it has an intermittent no start problem,I have changed the crank ... A: I apologize, but I do not have any experience on late model Eagles, only the older models built by ... | |
| CARFAX-Odometer Readings | 11/13/2005 |
| Q: If I buy a used car from a dealer, should he already have had it inspected or is this something ... A: Most dealers will have their used cars inspected. Usually. I still would not trust them. Tell them ... | |
| 1964 AMC Rambler American 330 Electrical Problem | 11/7/2005 |
| Q: Kevin, My husband did remove the postive cable and touched it to ground and it does spark. We ... A: OK, you got me. All the years I've been around Ramblers, I have never experiened this condition. ... | |
| 1964 AMC Rambler American 330 Electrical Problem | 11/7/2005 |
| Q: Our daughter's car does the following: When the battery is disconnected and touch hot wire to ground ... A: I'm not sure I understand you. If you remove the positive cable from the battery, and touch the ... | |
| gremlin electrical problem | 11/4/2005 |
| Q: we have a 1977 amc gemlin. IT HAS A NEW 232 6CYL ENGINE, NEW STARTER,CABLES, SOLENOID, THE WIRES TO ... A: Try the following: 1) Turn the key to the "ON" position 2) Check for 12 Volts at the + side of the ... | |
| 1994 buick lesabre want start | 10/24/2005 |
| Q: i have a 1994 buick lesabre and i just bought a new starter and i have a fully charged battery.the ... A: I do not have experience with Buicks. My category is vehicles manufactured by American Motors ... | |
| cooling system | 10/17/2005 |
| Q: I have a 1981 AMC eagle SX/4 with the 258 engine and an automatic transmission. The frist year I ... A: Got a good one here. If you can place your hand on the upper hose, it could mean the coolant is ... | |
| cooling system | 10/17/2005 |
| Q: I have a 1981 AMC eagle SX/4 with the 258 engine and an automatic transmission. The frist year I ... A: How long does it take for the engine to get to operating temperature when it is cold outside? and in ... | |
| Automatic Transmission for a 68 american | 10/11/2005 |
| Q: I live in California and I am looking for somone to look at the transmission on my 68 american. it ... A: Please go to the following websight. You should be able to find a shop near by. http://www.atra.com/ ... | |
| 1978 AMC JEEP 360 Motor | 10/9/2005 |
| Q: Well, I have just come across a 1978 Jeep 360 motor out of I think a Jeep Truck or Cherokee. Don't ... A: Here are the asnswers to your questions: 1) AMC manufactured their own engines. They are unique to ... | |
| 91 pontiac grand am | 10/8/2005 |
| Q: Tonight on my way home from work my 91 grand am started to shutter as i accelerated and didnt seem ... A: I am sorry, but my expertise lies with vehicles manufactured by American Motors Corporation such as ... | |
| Production number | 10/7/2005 |
| Q: I have an AMC Rambler 66 Convertible 770 body, built in Kenosa, USA. Production number A6KS75A106650 ... A: The number you sent is called the VIN (vehicle identification number) It can be read as: A- American ... | |
| theft system light | 9/23/2005 |
| Q: i have a question about my theft light being on no i can't seem to get it out i am working on a ... A: Tim, I aplogize, but my experience is with vehicles made by American Motors Corporation. i.e. ... | |
| Undercarriage Damage | 8/22/2005 |
| Q: I was looking for a car and I found one that runs good and everything at a really great price, but I ... A: The term "under carriage damage" can mean anything from a scratch under the bottom of the car to a ... | |
| Car Problem | 8/21/2005 |
| Q: Hey Kevin, I am not sure if you can answer my question or know someone that might be able to help. ... A: Kyle, Sorry, but my experience is with vehicles made by American Motors Corporation. I have not ... | |
| More voltage, Gen. | 8/15/2005 |
| Q: I have a 1956 Hud. Metro. The Gen. puts out 12.5 to 12.9. My question, is there a way to inclrease ... A: Vehicles with generators have a external mechanical voltage regulator. Most regulators can be ... | |
| Brand New Car | 8/10/2005 |
| Q: I recently bought a brand new car. and i rarely use it. My question is, what will happen if i dont ... A: There should be no problem leaving the vehicle undriven for a week or two. Any longer and you might ... | |
| My 1983 Spirit sets too high... | 7/27/2005 |
| Q: My 1983 Spirit sets too high in the front. I suspect that the springs may have been replaced as the ... A: Bill, AMC used different srpings on 4,6,& V-8 Spirits. Also cars with and w/o AC. Is your car ... | |
| advice | 7/13/2005 |
| Q: I am looking for a used american car for 2 to 5 thousand $'s, I need a small car that can save gas ... A: To be honest with you, I couldn't suggest an American car that fits your description. Per Consumer ... | |
| Vapor Lock, I think | 6/26/2005 |
| Q: I called my brother and he told me that this is a 1993 Buick Lasabor, with a 3.8 Letter injected. ... A: Tim, First, I apologize for not responding to your reply. Your message got lost in All Experts ... | |
| Vapor Lock, I think | 6/25/2005 |
| Q: I wanted to write to you tonight to find out what is going on with my brothers car. About two weeks ... A: Tim, Even though my specialty is with vehicles built by American Motors Corporation, not GM, I will ... | |
| squeak/thunk when put into Drive | 4/24/2005 |
| Q: I own a 95, 2.2L Cavalier with a 3speed automatic transmission. When I put the car into drive from ... A: Sam, Sorry to hear about the problem you're having with your Chevy. Unfortunately, my expertise is ... | |
| cars | 3/14/2005 |
| Q: I have a question on cars that i'm quite interested in and wondering if you can answer me. Can you ... A: Let me start off by telling you that I know nothing about the Canadian automobile industry. If you ... | |
| wires | 3/7/2005 |
| Q: Will a wire harness for a 91 Lincoln Mark VII work on a 89 Lincoln Town Car? A: My knowledge is limited to vehicles manufactured by American Motors Corporation from 1949-1982. ... | |
| Body parts | 2/21/2005 |
| Q: I've tried the sites you recommended with no results. You mentioned a number to a dealer. If you ... A: The name of the dealer is Collier Motors in Pikeville, NC. It is owned by Robert Collier. He and his ... | |
| Body parts | 2/21/2005 |
| Q: I am currently restoring a 76 Matador 2-door coupe and I am having extreme difficulty finding a hood ... A: There are a few places to check. 1) Go to the AMO Club websight. www.amonational.com Click on links ... | |
| batery goes dead how do you... | 2/12/2005 |
| Q: batery goes dead how do you check altinator A: To properly test an alterator, you need a Voltmeter and an Ammeter. An alternator should put out at ... | |
| 1999 Chrysler 300M | 1/30/2005 |
| Q: I am not sure if you are the person to ask, but there isn't anyone in the chrysler section. I ... A: I do not know anything about 99 Chryslers so the answer I give you is generic. In regards to your ... | |
| amc trans | 1/29/2005 |
| Q: -------------------------I plan on rebuilding the car as a performanace street machine, but will ... A: The answer to your first question would be too long for this message board. I would, however, ... | |
| amc trans | 1/28/2005 |
| Q: 1973 Javelin. Can you tell me the differance's between the amc and mopar trans.( 727,904,998 etc.)? ... A: Bryan, An AMC with a 304 would not have a 727 trans, unless it was a special order fleet vehicle; ... | |
| Engine hesitation | 1/27/2005 |
| Q: Kevin, First off, thank you for responding so quickly to my question. And yes, my check engine ... A: If your check engine light comes on, I would recommend bringing it to a competent mechanic. They ... | |
| Engine hesitation | 1/26/2005 |
| Q: Kevin, I own a 2003 Cavalier base model. And today on my way to work my car seemed to hesitate ... A: You could be heading in the right direction. However, if the car is performing poorly because of ... | |
| american motors,electric wipers | 1/8/2005 |
| Q: THIS THE SECOND TIME I'M ASKING THESE QUESTIONS,I'VE A 70 AMX W/ ELECTRIC WIPERS I'VE A NEW WIPER ... A: Anytime you are looking for an obsolete part, it will take some phone calls. I do not know where you ... | |
| Battery CCA | 1/4/2005 |
| Q: I have what will probably sound like a fairly ignorant question, but since I don't know the answer, ... A: Morad, There should be no problem in replacing your battery with one with greater CCA; as long as ... | |
| electric wipers eccentric cam | 12/22/2004 |
| Q: 1970 AMX W/ELECTRIC WIPERS. I'M REPLACING WIPER MOTOR ,PARTS OF ECCENTRIC CAM HAVE RUSTED BEYOND ... A: You should be able to find replacement parts. Possibly NOS, or used. Let me give you 3 sources. 1) ... | |
| General Motor | 12/10/2004 |
| Q: I got two question about this comapny General Motor 1. What government regulations affect this ... A: My expertise is technically related to automobiles manufactured by American Motors Corporation. I do ... | |
| on automobile mechanic and automobile technician | 12/1/2004 |
| Q: can someone be an automobile mechanic and at the same time be an automobile technician A: Yes. They are the same position. In an effort to increase professionalism, many companies use the ... | |
| Sorry...It is a 1969 AMX.... | 11/23/2004 |
| Q: Sorry...It is a 1969 AMX. I figured out the Alternator abd VR but still havent got the Tach working. ... A: OK, I found the correct wiring scheme for your tach. Pretend the Hy Fire isn't there for the time ... | |
| I just replaced my Leece alternator... | 11/21/2004 |
| Q: I just replaced my Leece alternator (built in Reg) with the correct Alternator from Advance Auto. I ... A: I apologize, but my specialty is in vehicles manufactured by American Motors Corporation. i.e. ... | |
| tail pipe | 11/15/2004 |
| Q: I live in Trenton, NJ and own a 2002 chevy malibu. I was resently talking with a friend, about to ... A: What you are seeing is condensation forming in the exhaust system, normal. The catalitic converter ... | |
| MPFI | 10/26/2004 |
| Q: what actually is MPFi and what is the difference between it and the conventional form of injection ... A: MPFI is Multi Point Fuel Injection. The computer controled system consists of a fuel injector for ... | |
| 1976 AMC Mail Truck | 9/29/2004 |
| Q: I am trying to find the current value of a 1976 AMC mail truck for purposes of a property damage ... A: Hemmings Motor News publishes a book titled "Collectible vehicle value guide". It is around $10 and ... | |
| dellorean motor | 9/22/2004 |
| Q: i have a 1981 dellorean with no motor and 4 boxes of the motor parts , the person he sold this car ... A: The engine used in the DeLorean is known as the PRV. It is manufactured by Renault, but is also used ... | |
| 2000 chrysler grand voyager se window motor | 9/20/2004 |
| Q: how do i change the motor in my 2000 chrysler grand voyager se i bought the part but cant figure out ... A: Please direct your question to the Chrysler, Dodge or Plymouth expert. I specialize in vehicles ... | |
| '75 AMC HONET coil spring | 9/7/2004 |
| Q: I have a '75 hornet need to replace coil springs. Is there an easy way? If not, best way to put ... A: Are you talking about the valve springs or front suspension springs? If you plan on replacing the ... | |
| 93 AMC Summit mini van | 8/24/2004 |
| Q: My husband changed the starter in January. Since then I have been having trouble starting it. It ... A: I am not familiar with an AMC Summit mini van. AMC was not in business in 1993. I can help with AMC ... | |
| Jeep Grand Wagoneer..1987 | 7/22/2004 |
| Q: Were Jeeps mfg by AMC in the 80's? Answer - Jeep was made by AMC from February 1970 until Chrysler ... A: If the engine and transmission were maintained properly, they should be fairly reliable. The areas ... | |
| Jeep Grand Wagoneer..1987 | 7/22/2004 |
| Q: Were Jeeps mfg by AMC in the 80's? A: Jeep was made by AMC from February 1970 until Chrysler bought them out around 1978. As for your ... | |
| AMC Hornet | 6/28/2004 |
| Q: There are mice in it. They have chewed up the carpet but haven't touched the seats (Good) I have ... A: The extermination of rodents is out of my area of expertise. Maybe try and prevent the mice from ... | |
| AMC Hornet | 6/24/2004 |
| Q: I have a 1970 AMC Hornet SST that has been siitng out on a farm field for over 10 yers, I am trying ... A: 1) Look for critters that may have made the car their home. Field mice, rats, snakes, etc. They can ... | |
| brakes | 6/21/2004 |
| Q: I started my car and the power brakes just gave out on me. They can be depressed and the car will ... A: You didn't say what kind of vehicle you have. Most have a vaccuum hose running to the brake booster ... | |
| Jeep Guages, 1995 Wrangler | 6/13/2004 |
| Q: All the instruments have stopped working. The fuse is OK. It acts like there is an open circuit ... A: I would strongly recommend finding an electrical wiring diagram for your vehicle. This could be ... | |
| windshield scratches | 5/27/2004 |
| Q: Kevin,this question is not American Motors specific, but do you know what I can use to remove ... A: There is a special product specialists use for removing small scratches in glass. It is used with a ... | |
| 83 cj-7 engine | 5/11/2004 |
| Q: my 83 cj-7 straight six will start and only run for a couple minutes then die and not start again. ... A: 1) confirm spark by pulling the large coil wire off of the center of the distributor cap, hold it ... | |
| ambassador 65 | 5/6/2004 |
| Q: I need to replace the electrical wiring harness for a 1965 ambassador 990. Can a buy something new. A: I doubt if you will find an NOS wire harness. The best place to check is Hemmings. You can pick one ... | |
| Hello, Kevin! I'd like to... | 5/1/2004 |
| Q: Kevin! I'd like to ask you, how replace an ignition switch in corsica 93 or where to find this info ... A: I would recommend submitting this your question to the Chevrolet expert. My knowledge is limited to ... | |
| where can i find a motor for... | 4/27/2004 |
| Q: where can i find a motor for a 1985 98 oldsmbilewith a distribder that word may not be spell right A: I would recommend you submit this question to the Oldsmobile, Chevrolet, Buick, or Pontiac expert. ... | |
| tachometer | 4/20/2004 |
| Q: ok i bought a apc tach and for some reason i can't figure out where the ignition wire goes i have ... A: If you were connecting your tach to an car made by American Motors, like a Pacer, Gremin, or ... | |
| 1970 amx automatic transmission | 4/1/2004 |
| Q: Sir, I've owned a 1970 american motors amx since 1982. It's a 390 automatic that I bought from ... A: If your engine has a crank from a 390, it will have to be modified before installing a 727. It ... | |
| Hello, Kevin. I have Chevy... | 3/28/2004 |
| Q: Kevin. I have Chevy Corsica 4 cil. It is difficult for me to hold a brake pedal at the light, so I ... A: Sorry for the delay. I responded to your question a few days ago, but there must be technical glich ... | |
| Radiator..... Bone..... Dry.... | 3/25/2004 |
| Q: computers are more my thing than cars, and as such i have a fairly general question. I have a 1990 ... A: Remove the radiator cap after the vehicle has been sitting for a few hours, cold. Start the engine, ... | |
| Hello My van Astro van... | 3/24/2004 |
| Q: My van Astro van has no other place now but park under the strong Arizona sun. 1 would it hurt ... A: If you drive regularly, the sun shouldn't affect the hoses and belts. I would have them checked at ... | |
| Ignition Coil '87 Eagle | 3/18/2004 |
| Q: I need to replace the ignition coil... it looks fairly straight-forward. I don't have the repair ... A: It's a basic remove and replace procedure. Disconnect the wires from the original coil, pay ... | |
| Gas & Temp Gauge Readings Jump Around... | 3/18/2004 |
| Q: I have a question about Dash gauges. The car is a 74 AMC Javelin. The Gas and Temp gauges seem to ... A: It does sound as though the CVR (constant voltage regulator) is the cause of your problem. It is ... | |
| 2000 grand prix electrical | 3/16/2004 |
| Q: I know you are not a pontiac guy , but i am getting power to all fuses and my cig lighter, my cruise ... A: You're right, I don't know much about Pontiacs. I would reccommend submitting this question to the ... | |
| Proportioning Valve / Brake Warning Light.... | 3/16/2004 |
| Q: This is my second attempt. I somehow wiped out the whole question a minute ago.? I am working on a ... A: 1) When the key is on, the brake light should illuminate for a bulb test, HOWEVER, if the sensor ... | |
| 87 amc eagle flex plate replacement | 2/19/2004 |
| Q: I need to replace a flex plate on my eagle are there any special tools needed to do this or is it ... A: Because you are dealing with a 4 wheel drive vehicle, performing this repair in the driveway on ... | |
| Bleeding Brake lines | 1/4/2004 |
| Q: I have an 84' Mercury Gran Marqui And I took a brake cylinder out awhile ago and did'nt bleed the ... A: I admire you for wanting to work on your car, unfortunately, when dealing with critical components ... | |
Kevin Pilotte
Top Expert on this page
Expertise
I can answer many technical questions relating to AMC vehicles prior to 1979. I also have experience with Rambler & Nash vehicles.
Experience
I am a former AMC technician, service writer and service manager. I have worked in AMC dealers in Illinois in the 70's. After college, I was a Field Service Rep for American Motors Sales Corporation, working out of the Chicago Zone office. I traveled to AMC dealers assisting in the diagnosis and repair of AMC vehicles. I was also the Area Training Manager for DeLorean Motor Company. I have 10+ years as an Automotive Instructor. I have modified and restored
numerous AMC vehicles. I have been working on AMC vehicles for over 30 years.
Organizations
I have been an ASE Certified Master Technician since 1975. This includes L1. I am also currently a Toyota Certified Master Diagnostic Technician.
Publications
I have articles in "American Motoring", the official publication of the American Motors Owners Association. They are the largest AMC club in the world.
Education/Credentials
I have a certificate I printed out from a website.
©2012 About.com, a part of The New York Times Company. All rights reserved.