	AllExperts > Experts
	Search

About Skip Bollinger
(Top Expert on this page)

Expertise
Heretofore, I will NOT answer any mechanical question. I am not qualified and can only offer speculations. You are better served by others that are true Techs. With that being said, please only ask about parts and locating obsolete Auto Parts. Thank you. I have the ability to locate quite a few mechanical parts for American made vehicles fron the 1900`s to present. Some are OEM and some are aftermarket. This would include engine, brake and chassis parts. Body parts and trim are VERY difficult to find but you may inquire. If you need assistance in repair, I have illustrated books for major American manufacturers that show some illustrations BEFORE 1974. If needed, I can supply repair manuals for your specific vehicle. PLEASE REMEBER I'M A PARTS SPECIALIST, NOT A TECH!! Thank you.. Skip

Experience

Past/Present clients
Too many to list but they run from Europe through America and to Australia.

You are here: Experts > Industry > Transportation and Logistics > Automotive

Questions Answered By Expert Skip Bollinger
In Category Automotive

Subject	Date Asked

a/c mounting brackets	8/1/2008
Q: I bought an '81 chev dually camper van a few years back.The fellow I purchased it from had removed ... A: Rick, Wow!! This is a tough one!! This van is 27 years old. Okay, you are looking for a ...
Sun Visors	7/31/2008
Q: Skip, I need sun visors with the flipup mirrors, also the mounting brackets, for a 2002 GMC Sonoma ... A: Mac, There is a salvage yard in Joliet, Illinois that is computer linked to over 1,000 other ...
F150 4 wheel drive 1996	7/28/2008
Q: I need help with my 4 wheel drive system. My truck had a 4 wheel drive selector in it at one time. ... A: Randall, The parts you require have never been offered in the aftermarket. I'm really not sure ...
bumper schematic	7/25/2008
Q: Skip, my gf recently backed my 04 chevy trlblzer into a tree and jarred the bumper out of its guides ... A: David, This question is SO far out of my realm of expertise, I shouldn't even be offering these ...
1973 VW Beetle	7/21/2008
Q: As per you bio, you can help with some manuals prior to 1974. I am in need of a manual for the 1973 ... A: Satcatcher, I will have to do some homework on this. I, primarily, deal with domestic vehicles. I ...
Engine Swap	7/19/2008
Q: I have a 1985 Mazda RX-7 that I want to drop a performance engine into. I will be drifting the car, ... A: David, I'm sorry to take so long to get back with you but my wife and I are busy planning a trip ...
98 GMC Sierra	7/9/2008
Q: my windshield wipers were only working when they were wanting to and would only work on the fastest ... A: Christina, Please know that I'm a Parts Professional, NOT a Tech. This is explained in my ...
2000 dodge neon	7/6/2008
Q: windshieldwipers quit working A: George, As stated in my Profile, I'm a Parts Professional, NOT a Tech but will offer these ...
oxygen sensor for 2002 ford explorer	7/4/2008
Q: I did a code reading on my ford explorer-2002,the code said that the oxygen sensor was bad-Bank one ... A: Don, You need to ask someone smarter than I. I'm a Parts Professional, NOT a Tech but will offer ...
replacing transmitssion fluid	7/3/2008
Q: how do i replace the transmission fluid in my 94 mustang v6 5 spd A: Dallas, As stated in my Profile, I'm a Parts Professional, NOT a tech but I think I may be able ...
right side blinker bulbs are out	6/28/2008
Q: I have a 94 oldsmobile cutless, and I'm trying to change the bulbs. Its not the fuse, I've checked ... A: Lelia, I take it, by your question, that BOTH right side blinker lamps, front and rear are not ...
1983 BMW 320I	6/25/2008
Q: MY CLUCH GOES INTO GEAR WITH THE CLUCH DEPRESSED, I HAVE REPLACED THE SLAVE CYLINDER AND HAVE BLEED ... A: Don, I'm a bit confused by your question. You state "My clutch goes into gear with the clutch ...
90 geo	6/20/2008
Q: skip your site is phat "". any who i am looking for a torque strut 'engine stabilizer for a 1990 geo ... A: Michael, I looked through every catalog I have and cannot find a "Torque Strut" for that car. I ...
95 mitsubishi galant s	6/11/2008
Q: I cahnged the spark plugs the wires the oil the breather and the distributor and now my car want ... A: Teona, You gave me your phone number and I tried to call you. I left a message. I never heard ...
Location Of A/C Relay	6/9/2008
Q: I have a 1994 Chevy Z71 4WD eatended cab pickup with a 350 engine. I can not find the A/C relay; can ... A: Leon, I'm sorry to take so long to get back with you but I'm a Parts Professional, NOT a Tech but ...
heater/ac memory card	6/3/2008
Q: I have a 1999 Oldsmobile Intrigue with dual air /heater controls. We were told bye the mechanic that ... A: Bill, I know of NO Parts Specialist that can answer this question. It is a Dealer Only part. They ...
96 Honda Accord Antenna	5/29/2008
Q: Recently purchased this car. Radio/CD is a custom job. I was looking for the antenna and I just ... A: Jack, I'm a Parts Professional. What you are looking for is totally aftermarket so all I can do ...
volkswagon speedometer	5/25/2008
Q: I have purchased a 1970 Volkswagon trike with a 1600cc motor and a 67 transaxle for my dad. I need ... A: Chrissy, FINALLY a Parts Question,,,, THANK YOU!!! Not the easiest question but I have an answer ...
camshft position 98 SHOV8	5/23/2008
Q: My Taurus sho sprocket spun on the cam shaft but i don't know where i position it back at there is ... A: Justin, As stated in my Profile, I'm a Parts Professional, NOT a tech but I can give you some ...
a/c compressor relay l ocation	5/21/2008
Q: where is a/c relay and compressor relay located A: Jaz, Your question, to anyone, needs to include the Year, Make and Model. You supply none of ...
air intake hose	5/13/2008
Q: i have a 1996 camry.i just bought a air intake hose for it.they send me the wrong one.i guess i need ... A: Greg, My most sincere apologies for taking so long to get back with you. We are short handed at ...
1988 chevy beretta engine being held back	5/12/2008
Q: i did a head job on the car and now it acts like it is being held back , it runs but something is ... A: Ed, I'm NOT a Tech, Okay? I put that in my profile, I'm a Parts Professional. I do have some ...
Glove Box (liner?)	5/11/2008
Q: Need replacement for 1966 Mercury Park Lane Convertible. Has factory A/C Installed. A: Ken, Wow! What a land yacht was a '66 Park Lane!! It's been a long time since I've seen one of ...
clock in a 2000 Chevy Venture Van	5/7/2008
Q: Since I bought this second hand, it didn't have a manual with it. I cannot figure out how to set the ... A: Patricia, The best thing for you to do is go to "www.helminc.com" and request an owner's manual ...
Hood latch	5/3/2008
Q: I was wonder what do I have to do to reinstall the pully for the hood latch? A: Cliffton, I'm a Parts Specialist, not a Body Repair Tech OR a Mechanical Tech but have some ideas ...
Car ac problem	4/26/2008
Q: I have mitsubishi lancer 2003 model in saudi arabia. facing problem in ac cooling after 1/2 hour low ... A: Rehan, This question is out of my area of expertise. I'm a Parts Professional, NOT a Tech but ...
driver front door	4/24/2008
Q: window fell off the track because of a broken clip.took it to pepboys they said they don't have the ... A: Margaret, I have copied your mail into this response. You open up a LOT of questions. I'm going ...
92 honda prelude died on highway	4/21/2008
Q: I have a 92 prelude was on the highway started accelerating and check engine light came on, lost all ... A: Cary, This question is out of my realm of expertise but will offer some thoughts for you... ...
2002 Dodge caravan - turning the defrost on will result in a loud noise	4/20/2008
Q: I hear a loud click when I rotate the funtion button to the defrost position, however if I move it ... A: G. If the system has no freon, there is a "low pressure switch" that keeps the compressor from ...
2002 Dodge caravan - turning the defrost on will result in a loud noise	4/19/2008
Q: I hear a loud click when I rotate the funtion button to the defrost position, however if I move it ... A: G. I am a Parts Specialist, NOT a Tech but will off these thoughts for you to ponder. Your mail ...
2001 Audi TT	4/14/2008
Q: The dealership just told me I should replace the valve cover gasket because of oil leaking. They ... A: Duane, Yes, an oil leak is major. Not only does it leak oil, it is a fire hazard. This depends on ...
achieva's 95 cooling system	4/12/2008
Q: my car keeps heating up, cleaned the radiator, installed a new water pump, got the fan with direct ... A: Julian, I am a Parts Professional, NOT a Tech and NOT qualified to answer this question but will ...
Pontiac	4/11/2008
Q: What make/model auto windshield is comparable to a 1990 Pontiac Bonneville? A: Frank, I am a Parts Professional and run a Parts Store. No Parts Store sells windshields so I am ...
humming noise	4/8/2008
Q: I have a 2003 mazda protege 5 with 53000 miles on it. At the speeds 38,39 mph ,i hear a slight ... A: Robbie, The car is humming because it doesn't know the words to the song. Old joke, sorry... ...
Camry window fuses	4/7/2008
Q: Where is the fuse for the other 3 (not drivers) windows on a '97 Camry? Any other reason why those 3 ... A: Clarke, I'm a Parts Professional, as stated in my Profile, NOT a Tech, but do have a couple of ...
timing	4/6/2008
Q: I just replace the timing belt on my 1997 Ford Escort and i cant get it start still what could it be ... A: Manuel, I'm a Parts Professional, NOT a Tech but will offer some thoughts for you to ponder. ...
CB-CC Headlights	4/4/2008
Q: I have a 1994 CC Lancer (CB shape 5 door) the low beam headlights have stopped working, high beam ... A: Greg, Where on God's Green Globe are living?? I have never heard of a CC Lancer and here in the ...
1993 Honda Accord, All the Gauge Problem	3/29/2008
Q: Bollinger. I just bought the 93' honda Acc, and all the dash gauge are work, but the light in side ... A: Dave, I'm a Parts Professional, NOT a Technician. I do have some thoughts about your question so ...
93 eagle talon dl	3/28/2008
Q: I decided to change the air intake hose because mine was in really bad shape then right after i did ... A: Tristan, As I stated in my Profile, I'm a Parts Professional, NOT a Tech but will offer these ...
Backup lights/neutral switch	3/13/2008
Q: Once in a while my backup lights will briefly turn on when I put the car in reverse so I know the ... A: David, In retrospect, things could have been worse for me. When Mom fell, she could have broken a ...
05 Stratus front lights just go out?	3/12/2008
Q: As I'm driving to work today, doing around 65-70, radio on, heater turned on low and my son's DVD ... A: Monica, I am NOT qualified to answer this question but will offer these thoughts for you. I'm a ...
Backup lights/neutral switch	3/11/2008
Q: Once in a while my backup lights will briefly turn on when I put the car in reverse so I know the ... A: David, Sorry to take so long to get back with you but my Mother was discharged from the Hospital ...
Backup lights/neutral switch	3/10/2008
Q: Once in a while my backup lights will briefly turn on when I put the car in reverse so I know the ... A: David, Thank you for your question. Please remember I'm a Parts Professional, NOT a Tech. This is ...
ford vacuum lines	3/4/2008
Q: 92 f250 4x4 i have a missing vacuum line ,and can't find where it goes. Where can i find diagrams or ... A: Andrew, Thank you for understanding my profession. You know I'm NOT a Tech and have phrased your ...
Auto repair manual binder	3/3/2008
Q: what is that long binder you see in shops or auto stores that holds all of the manuals or catalogs ... A: Missy, FINALLY, a question that I can answer with confidence!! Thank YOU!! Miss, I know this ...
serpentine belt	3/2/2008
Q: how to install serpentine belt on a 2001 chevy silverado 4 x 4 pick-up truck? A: Gary, I'm a Parts Professional, NOT a Tech but I will offer these thoughts for you to ponder. ...
Changing Oil Pan 1991 Ford LTD 5.0 engine	2/26/2008
Q: Can the oil pan be removed & replaced on this car without pulling the engine from the car? thanks A: Ray, I am NOT A TECH but can direct you to the place that can assist you. In your Public Library, ...
fuel gague audi 2.3e coupe	2/25/2008
Q: el fuel gague not working 2.3e audi coupe any ideas A: Stu, I'm a PARTS PROFESSIONAL, NOT a Tech but will offer this for your pondering. A fuel gauge is ...
96 Ford Club Wagon 5.8 liter V-8	2/21/2008
Q: How/where can I find the horsepower and torque ratings for my 7 passenger Chateau XLT van? Can't ... A: West, I don't have any manuals for a vehicle that new but you can go to any Public Library. They ...
VW Transporter transmission	2/18/2008
Q: Skip, I have a '93 VW Transporter 1.9l diesel. Can you tell me what other years/engine ... A: Richard, To all who have questions pending with me, I'm sorry. My Mother fell last Monday and ...
computer chip	2/17/2008
Q: I am looking for computer chip or chips for a 1992 s-10 pickup 2.8, 6 cylinder. I purchased a ... A: Clyde, To all who have questions pending with me, I'm sorry. My Mother fell last Monday and broke ...
speed sensor	2/16/2008
Q: where is the exact location of the speed sensor on a 99 chevy lumina? A: Sandy, To all who have questions pending with me, I'm sorry. My Mother fell last Monday and broke ...
86 ford F-250 Diesel	2/12/2008
Q: Need a part for a 1986 Ford F-250 Diesel. I believe the part that is being replaced is called a ... A: Carl, I'm sorry to have taken so long to get back to you. Once you gave me the OEM number, I ...
Dash removal	2/11/2008
Q: I own a 2005 Dodge Neon SXT and am trying to remove basically my whole front dash. I want to install ... A: Brandon, I am SOOOO sorry to take so long to get back with you but my Mother fell and broke her ...
86 ford F-250 Diesel	2/8/2008
Q: Need a part for a 1986 Ford F-250 Diesel. I believe the part that is being replaced is called a ... A: Carl, Give me the entire VIN (Vehicle Identification Number). It can be seen through the driver's ...
86 ford F-250 Diesel	2/7/2008
Q: Need a part for a 1986 Ford F-250 Diesel. I believe the part that is being replaced is called a ... A: Carl, This piece is an OEM (Original Equipment Manufacturer) part only. I become a bit jittery ...
torque settings for water pump	2/6/2008
Q: Gmc Suburban 5.7L. What is torque settings for the four bolts on the water pump? A: Jim, I'm NOT A TECH but this would be easy IF I knew what year and bolt diameter with which you ...
92 F150 water pump heater connection	2/5/2008
Q: I'm trying to find a replacement for the pressed in heater hose fitting that on the water pump. ... A: Frank, Tell me what size the fitting needs to be. I can get it for you but we will have to get ...
92 F150 water pump heater connection	2/2/2008
Q: I'm trying to find a replacement for the pressed in heater hose fitting that on the water pump. ... A: Frank, All I can give you is speculation and part numbers since I have no idea what size engine ...
95'96 GMC Jimmy	1/30/2008
Q: I was going to put an engine from a 96 Jimmy into a 95 Jimmy I was told that I may have to switch ... A: Ewald, Sorry to take so long to respond but I have been having phone problems here in the house ...
malfunction light	1/28/2008
Q: The malfunction light came on while i was driving my 2007 charger. other lights came on like brake ... A: Ervin, Wow, from Russia... Ervin, I'm not qualified to answer your question but will give my best ...
changing a punctured oil pan nissan altima 05	1/27/2008
Q: I ran over some trash in the road. pulled over, checked for damage and what i hit, -a steel mesh ... A: Julie, I'm not better than you. I'm a Parts Professional also, NOT a Tech. I am not qualified to ...
Mitsubishi Lancer Evolution IX MR Edition	1/22/2008
Q: Mitsubishi Lancer Evolution IX MR Edition (1) If I purchase a brand new factory stock car, do I ... A: Evo, I'm a Parts Professional, NOT an attorney OR an Insurance Agent. I'm NOT from the state of ...
vw bettle 1975	1/20/2008
Q: where is the screw to control the ideling on the carburator A: Joel, As said in my Profile, I'm a Parts Professional, NOT A TECH!! Here is a web site that you, ...
no headlights!!	1/18/2008
Q: i had my truck detailed and they washed the motor it didnt start right away they flooded it but ... A: Cindy, This is a repair question and I'm not qualified to answer repair questions on newer ...
Low heat on Heater output	1/16/2008
Q: My 1991 300zx is not producing much heat through the vents (i.e. 50 degrees). This is a digital ... A: Tim, This is a repair question, NOT a parts question, Okay? I will offer you my thoughts but ...
2000 chevy s10	1/15/2008
Q: I figured a guy with the same last name as mine might be able to help me out. I have a 4 cylinder ... A: Tim Who?? I have no relatives named Tim?? Just joking but this is getting close to the last Tech ...
gas smell	1/14/2008
Q: I just bought a 92 plymouth acclaim, i started to smell gas the day after i bought it. I looked ... A: To Jeremy and all future inquiries, This a repair question and I am about done with them. I'm a ...
1989 Chevy Silverado Brakes	1/13/2008
Q: There is a leak in my brake line just above the rear axle. Is there a way to by pass the rear ... A: Shawn, This is a repair question and I'm trying to wean inquiries to Parts Locating, NOT repair ...
1984 Cadillac key missing	1/10/2008
Q: I have been asked by a friend to find out how to get a key for a 1984 Cadillac. Her friend died and ... A: Eliza, Only 2 things come to mind. Get the VIN # which can be seen through the driver's side of ...
1990 blazer 4.3 ignition rotor	1/9/2008
Q: im trying to replace the rotor on my 4.3 blazer and cant seem to get it off it looks like it just ... A: Bobby, The problem with this ignition system is the distributor gets so hot, any oil that goes up ...
auto	1/6/2008
Q: 1990 dodge pick-up v8, why am i getting back pressure and making it over heat A: To all who read this. I have updated my Profile and will NOT attempt to answer any more Technical ...
1996 f350 7.3 liter	1/4/2008
Q: why does the turbo waste gate open when i excell slow A: Rick, I am NO Tech and when it comes to Diesels, I'm an idiot but I will offer this thought. A ...
Jasper rebuilt engine	1/3/2008
Q: I had a Jasper engine installed in my 1984 pontiac grand prix 5 years ago. I was told that the gas ... A: James, You ask a question but leave me with a LOT of questions. You neglected to tell me what ...
removal of door panel	1/1/2008
Q: I need to replace the outside door handle of a 2004 tracker but can not figure out how to remove the ... A: Mark, I'm a Parts Specialist, NOT a tech will offer these thoughts for your consideration. You ...
oil light in chevy impala 2004	10/22/2007
Q: my change engine oil light came on a week after I had it changed in my chevy impala 2004. I tried to ... A: Andre, Sorry to take so long but I have been having trouble getting to this web site. There is an ...
steering problem 2006 Malibu	10/21/2007
Q: My steering locks up on and off, I have to shut the car off and them the power steering starts ... A: Julia, I'm sorry to have taken so long to respond but once I found out some possible answers to ...
brake lights	10/20/2007
Q: On my 1999 Chevy Express Cargo Van ...my brake lights work fine as long as my headlights are not ... A: William, I am NOT qualified to answer this, I'm a Parts Pro, not a Tech, but will offer these ...
Air Intake hose for 1991 Geo Storm	10/20/2007
Q: I'm having a heck of a time finding one, and I've searched online for several hours. And the parts ... A: Janice, From what MY G.M. Dealer tells me, If the 8th digit in the VIN is a "5", the part number ...
1999 Ford Explorer Humming Sound	10/19/2007
Q: I currently own a 1999 FORD EXPLORER with approx. 80000 miles on it. The engine is a V6 OHV not ... A: Henry, I'm a Parts Professional, please remember that. I'm not Tech and don't feel qualified to ...
Intake manifold	10/18/2007
Q: Took my 1999 Grand AM in for routine oil change and everything appeared fine then the mechanic says ... A: Chris, You didn't tell me what size engine you have so I just a wild guess and went with a 3.4. ...
Air Intake hose for 1991 Geo Storm	10/17/2007
Q: I'm having a heck of a time finding one, and I've searched online for several hours. And the parts ... A: Janice, I ran your OEM part number through my computer system and it comes up zero. That number ...
1997 Grand Cherokee	10/16/2007
Q: When I crank my jeep up in the morning and let it run for a minute, then when I get on the road and ... A: C. I'm not qualified to answer this question but will give you some thoughts. I'm a Parts ...
1991 Plymouth laser	10/16/2007
Q: I have a 1991 plymouth laser. I just noticed it is leaking transmission fluid from under the car. ... A: Dan, I'm happy to have given you some positive direction. I looked in a Dorman Catalog but they ...
1991 Plymouth laser	10/16/2007
Q: I have a 1991 plymouth laser. I just noticed it is leaking transmission fluid from under the car. ... A: Dan, The only thing I can think of for you to do is a bit dangerous unless you have the proper ...
1991 Plymouth laser	10/15/2007
Q: I have a 1991 plymouth laser. I just noticed it is leaking transmission fluid from under the car. ... A: Dan, I'm no mechanic either. I'm a Parts Professional but when I earned my Automotive Degree ...
Air Intake hose for 1991 Geo Storm	10/15/2007
Q: I'm having a heck of a time finding one, and I've searched online for several hours. And the parts ... A: Janice, I need to know if it has 1 camshaft or 2 camshafts and so will Chevy. When you get back ...
Finding broken horn on 1980 Ford truck	10/13/2007
Q: I purchased a 1980 Ford F250 truck. The original horn on the truck does not work. The switch on the ... A: Demond, I'm a Parts Professional and NOT qualified to answer this question but I have some ideas ...
Air Intake hose for 1991 Geo Storm	10/13/2007
Q: I'm having a heck of a time finding one, and I've searched online for several hours. And the parts ... A: Janice, I had everything typed to you and All Experts lost the mail. In a nutshell, this is what ...
Air filter hose is damaged.	10/10/2007
Q: It is 1995 Toyota Camry (4Cyln, automatic). Resently I replaced the batter, as per the mechanics ... A: Santo, I looked at the starter for your car today at the store and it is a gear reduction starter ...
'90 Civic cutting out	10/10/2007
Q: I was driving last night. Came to a red light and intended to turn right. Did a "rolling" stop ... A: Ken, I will begin by saying I'm a Parts Professional, NOT a Tech but will give you some thoughts. ...
1989 F-250 diesel	10/9/2007
Q: i have replaced all the belts on the truck however i can unable to stop the belt that goes from the ... A: Travis, Is it making noise? A belt is rubber and on "long runs" such as between the crankshaft ...
Air filter hose is damaged.	10/8/2007
Q: It is 1995 Toyota Camry (4Cyln, automatic). Resently I replaced the batter, as per the mechanics ... A: Santo, It seems as if you have a drain on the battery or some dirty connections. Please remember, ...
1995 Mazda B4000 truck, V-6, 4.0	10/8/2007
Q: where is the knock sensor located for a 1995 Mazda B4000 truck? A: Loretta, I answered this once but apparently it got lost in the shuffle. I spoke to 2-3 different ...
1995 Mazda B4000 truck, V-6, 4.0	10/8/2007
Q: where is the knock sensor located for a 1995 Mazda B4000 truck? A: Loretta, I'm a Part Professional, not a Tech so I contacted Borg Warner, a major supplier of ...
E350 Ford Diesel 7.3 IDI	10/5/2007
Q: Oh man, I just found out some pretty bad news. I took the van in to get looked at. It has been ... A: Joshua, Please read my "Profile". I'm a Parts Specialist, NOT a Tech but will offer these ...
Emissions Test Failure	10/4/2007
Q: I just had my 1997 Mercury Sable Emission Test done today and the computer gave me some Trouble ... A: Daniel, Why do you want to change the Converter?? Let's do a test, Okay?? Get a piece of paper, ...
Emissions Test Failure	10/3/2007
Q: I just had my 1997 Mercury Sable Emission Test done today and the computer gave me some Trouble ... A: Daniel, Just to make sure we are on the same page, if you look at my Profile, I'm a Parts ...
car horn	10/2/2007
Q: how do i find my horn for a 1997 kia? A: Jack, I'm not sure if you are trying to find the horn on your car or a replacement horn. Any ...
air ride suspension 1998 f250 pickup	10/1/2007
Q: Skip you give excellent advice. My 1998 f250 air ride system is not working correctly. Drivers side ... A: Tim, Man, do you know how to suck up!!! Really, thank you for the kind words. I'm a Parts ...
89 chevy camaro	9/30/2007
Q: car starts then dies. It'll keep running by feathering the gas. It will only go up to 2500 RPM's ... A: Tim, You leave me with a lot of questions and a bit of criticism.. You don't tell me what size ...
93 Honda Civic won't start or charge	9/28/2007
Q: On my 93 Honda Civic, I left the headlights on all day one day and drained the battery, I got a jump ... A: Crystal, Please look at my profile, I'm a Parts Professional, NOT a Tech but will offer these ...
1998 dodge intrepid sensor computer needs to be replaced	9/25/2007
Q: how much will it cost to replace it the sensor computer?? A: Donald, I have never heard of a "sensor computer". I would imagine you are talking about the ...
ebrake light comes on when i hit my brakes firmly	9/23/2007
Q: yes i was trying to find out why my ebrake light comes on when i press my brakes firmly then goes ... A: Chris, Please note I'm a Parts Specialist, NOT a tech. I took your inquiry to work today and the ...
99 Ford Contour	9/20/2007
Q: My 99 Ford Contour is extremely sluggish in the lower gears - particularly when the air conditioner ... A: Elizabeth, May I preface this with two statements. I'm sorry to have taken so long to respond but ...
Honda Accord Dashboard light on	9/20/2007
Q: I was on way to work this morning when suddenly the brake, battery, doors, trunk and battery lamp ... A: Jesus, I am not qualified to answer this question and I have asked the community in which I work ...
02 Dodge Stratus PCV valve location	9/18/2007
Q: Also, would this valve be fairly easy to replace myself? Thanks for your time. A: Jason, You didn't tell me what size engine you have and the location differs on each engine. ...
Seat Belt Light on	9/17/2007
Q: I have a Toyota Van 2000 XLE, The Seat belt light on the drive keep turn on when even if I put my ... A: Henry, Please look at my profile. I'm a Parts Specialist, NOT a tech but I will offer my thoughts ...
vauxhall vectra 2002	9/16/2007
Q: My vauxhell vectra is leaking small amount of clear fluid intimittently? Any ideas please A: Cathy, This car is British made and I have never seen one in America. Please look at my profile, ...
1991 olds cutlass 3.1 H2O Pump	8/1/2007
Q: I own a 3.1 ltr 1991 olds cutlass. I have changed my wtr pump twice with no problems. But this time ... A: Phil, Permatex makes a product to repair threads. It is part number 81668. Sells for about $8.00. ...
supercharger replacement	7/31/2007
Q: I was wondering how difficult it would be to replace either A) the supercharger on a 1992 Buick ... A: Michael, Please remember, I'm a Parts Professional, NOT a Tech, Okay?? I have spoken to 3 of my ...
MY 89 BMW 325I TIMMING BELT	7/29/2007
Q: WHAT CAN I DO IF MY TIMMIG BELT BROKE WHILE I WAS DRIVING THE CAR. DO YOU KNOW IF I HAVE TO BUY A ... A: Oskar, Please let me preface this with 2 statements. I have 2 inquiries in front of yours but I'm ...
Nissan sentra 93 2dr	7/28/2007
Q: Day before yesterday, my car stopped on the way to my dads and wouldn't start back up. I was able to ... A: Veronica, Sorry for the delay but I wasn't POSITIVE about an answer but I had a gut feeling. I ...
1989 lincoln town car starter	7/26/2007
Q: when I tried to start my 89 lincoln the other day it wouldn't start. I could hear the started ... A: Destiny, I'm NOT a tech, I'm a Parts Professional. That is stated in my Profile but I do have ...
1995 ford e-150 van check engine light	7/25/2007
Q: I have a 95 ford econoline van and the check engine light is blown. i took off the panel and could ... A: Ree, I'm Parts Professional, not a Tech but contacted one of my customers and they printed out ...
"Shimming" my Hood	7/24/2007
Q: I put a new hood on my 2002 Hyundai Elantra GT. Well, the seams where it meets up with the fenders ... A: Rich, ANY parts store worth it's salt has body shims. If they don't stock them, they can get ...
honda air	7/23/2007
Q: I have a 99 honda civic 4 door, my friend drove my car and hit a pole causing the fan on my air ... A: Michelle, Your question is a bit confusing but I must insert something. I'm answering your ...
1994 Olds Cutlass	7/22/2007
Q: I 1994 Cutlass v6 3.1 automatic transmission with 160K miles. Ssometimes when I started the car and ... A: Steven, I'm so sorry to take so long to get back with you but I AM NOT SMARTER THAN A 5th GRADER ...
vaccum hose layout / daigram	7/22/2007
Q: I have a 1999 Chevy Astro passenger van. I was having problem with the AC not blowing air thru the ... A: Dave, Most GOOD Public Libraries have a "Reference Section". You cannot check out the books in ...
automotive	7/20/2007
Q: I have a 1994 GMC Vandura that was idling rough for a while, but now it dies almost immediately ... A: Brian, This question leads to a LOT of questions and answers. My first thought is a vacuum leak ...
taurus sho	7/18/2007
Q: where is the fuel filter on a 93 ford taurus sho located? A: Gabe, Sorry to take so long to get back with you but I'm getting my butt kicked at work. The ...
1995 Lincoln Towncar	7/17/2007
Q: Skip, my car all of a sudden began not starting for no apparent reason. This actually began about a ... A: Wanda, First of all, I'm not qualified to answer your question but will give you my thoughts. If ...
1995 lincoln town car cutting off when a reach 35 mile a hours	7/12/2007
Q: it cuts it start to cut off when i am driving but not when its idling ,i have donne complet tune up ... A: Joseph, Your inquiry raises more questions for me to ask you. Please look at my Profile, I'm a ...
Fuel System	7/12/2007
Q: I own a 1997 oldsmobile achieva. it is chugging and sputtering when i go to accelerate it also pukes ... A: Kate, Firstly let me tell you that I am a Parts Specialist, NOT a Tech. Okay??? Now to your ...
1997 S10	7/10/2007
Q: where is the pvc valve on 1997 S10 4.3 located? A: Don, The PCV should be located in the valve cover. If you go to the AC Delco web site: ...
'99 malibu ls intake manifold gasket & cooling system	7/7/2007
Q: yesterday i had to change the upper radiator hose in my mom's malibu. while doing some online ... A: Jeff, I looked on line and came up with nothing here in America but there is a Class Action Law ...
GMC compressor "chirps" when accelerating	7/6/2007
Q: Whenever I am accelerating or maintaining higher speeds (40-50 mph), my compressor "chirps" when it ... A: Heather, I am a Parts Professional, NOT a tech but will offer my thoughts... I have NEVER seen ...
95 Pontiac Grand AM	7/5/2007
Q: 190,000 miles on this vehicle eqipped with a 3.1 L V-6. Engine check light intermittently comes on, ... A: Jerry, I'm a bit confused but that is easy to do. Firstly, I'm not qualified to answer this ...
1999 f150 power window wierdness	7/1/2007
Q: Driver side window wont go down, hear clicking on fuse panel,motor inside door was warm to touch ... A: Tony, Please understand that I know enough about electricity to keep my tongue out of a wall ...
REAR AIR SUSPENSION	6/30/2007
Q: I HAVE A 2002 ENVOY AND THE REAR END HAS DROPPED. THE COMPRESSOR IS KICKING ON BUT NOTHING, I HAVE ... A: P, Yes, that is MUCH better. Okay, the system consists of 3 basic components. The compressor, ...
REAR AIR SUSPENSION	6/29/2007
Q: I HAVE A 2002 ENVOY AND THE REAR END HAS DROPPED. THE COMPRESSOR IS KICKING ON BUT NOTHING, I HAVE ... A: P. Please slow down. Your question is all over the map. The rear of your Envoy had dropped, ...
Timing for a 1990 S-10 Blazer 4.3	6/26/2007
Q: I just replaced the entire distributor on my S-10 Blazer 4.3. I marked the housing/engine timing ... A: Jerry, Please look at my profile. I'm a Parts Professional, NOT a tech. My Degree in Automotive ...
91 ranger dying	6/24/2007
Q: at first we thought he ran out of gas. then we put gas in there and it still would'nt start. do you ... A: Kevin, I would like to begin this response with this: I'm a parts specialist, NOT a tech. ...
97 dodge 1500 4x4 a/c problem	6/23/2007
Q: had a/c serviced no leaks detected but after a feew weeks the a/c is blowing warm again. not sure ... A: Brian, I would like to begin this response with this: I'm a parts specialist, NOT a tech. Okay??? ...
ABS	6/22/2007
Q: have problem with brake-ABS. The ABS start working (you can heard they working) just before the ... A: Christopher, I apologize for taking so long to respond but personally I'm not qualified to answer ...
oldsmobile	6/12/2007
Q: i have a 1992 olds 98 and i think my fuel pump is gone bad, my car will start cold run for a short ... A: Jak, I'm not a late model car guy either. I'm an OLD parts specialist that has been on a parts ...
Door pins and bushing	5/23/2007
Q: I had to replace the driver side pins and bushings on my 95 Honda civic, 2 door coupe. I marked the ... A: Mark, If you take a floor jack and a bath towel, you can put the towel on the "pad" of the floor ...
Air Suspension compressor relay location	5/21/2007
Q: 1997 Lincoln Continental - the air compressor for the air suspension has quit working. Where is the ... A: Mike, I'm sorry to take so long to get back with you on this but I have NO customers that can ...
1997 S10 Blazer 4.3 engine hesitation problem	5/19/2007
Q: I have a question concerning a 1997 S10 Blazer 4.3 4x2... it has a hesitation problem at idle or in ... A: Charles, As I learned in Auto Mechanics 100, check the tune up on the vehicle. Also check to see ...
chevy corsica 3.1 losing injector pulse	5/13/2007
Q: Sometimes I have a no start condition and other times it will start and run for a while and ... A: Jeremy, WOW, you know more about this that I do. I could have just clicked that "I can't help ...
1993 Grand am has new battery and altinator but won't start	5/9/2007
Q: My 1993 Pontiac Grand Am would not start so we tried to jump it and it still did not start. The next ... A: Carla, Please let me preface this response with this: I'm a Parts Professional, NOT a Tech... ...
1991 dodge dynasty 3.3L no oil up to rear rocker arm	5/7/2007
Q: Recently after making a squealing noise, I removed the rear valve cover and noticed 4 out of the 6 ... A: Gerry, There are 2 things promised to one when born, death and taxes. It is all over now and time ...
oil oan gasket	5/2/2007
Q: I have a 1993 F250 4x4 super cab. The oil pan gasket is leaking and was wondering if it is possible ... A: Steve, I'm a Parts Professional, NOT a tech but I will offer some thoughts to you. I have been on ...
1995 chevy s10 4.3 litre v6	5/1/2007
Q: my problem is that when i hit the gas, my truck does not get up to speed as quick as it used to, and ... A: Brandon, Higher static compression ratios require a better fuel (more octane) or the fuel will ...
92 ford tempo	4/30/2007
Q: when i give the car gas there is a squeal and when i let off the gas there is a squeal its not too ... A: Ben, I would like to preface this answer with this: I'm a Parts Professional, NOT a tech... Okay? ...
PVC Valve	4/27/2007
Q: Where is the PVC valve located on a 2000 Chevy Impala with a 3.8l V-6? A: Michael, Your PCV Valve should be located in the valve cover. I have gone to the Delco web site ...
1993 ford probe gt	4/26/2007
Q: we have a antifreeze leak at the front of the engine it looks like it is coming out of the front ... A: Jerry, If you have antifreeze coming out the camshaft seal, you better take it to a professional ...
engine is reving up	4/25/2007
Q: I have a 97 ford taurus GX. Last week the brakes started acting up. I had to push the brake almost ... A: Angie, I'm an idiot for even responding but I'm a Parts Specialist and attempt to help dozens of ...
1995 chevy s10 4.3 litre v6	4/24/2007
Q: my problem is that when i hit the gas, my truck does not get up to speed as quick as it used to, and ... A: Brandon, I'm a Parts Professional, NOT a tech but I have some ideas you might look at. The ...
Starter Problems	4/22/2007
Q: i have a 1997 Dodge Intrepid and its been sitting for a year now and i am finally going to fix it up ... A: Trevor, I'm sorry to be so lax in responding but I don't recall getting the original mail. I get ...
94 blazer	4/19/2007
Q: i have a 94 s-10 blazer and when i give it gas to get up to speed it bogs down and sounds like it is ... A: Jimmy, May I preface this response with this: I'm a Parts Professional, NOT a tech. I'm probably ...
1996 Beretta Z26	4/17/2007
Q: Hey, I have a 1996 Chevy Beretta Z26 3100 V6 Auto, and I was wondering if you know where I might ... A: Annie, Specifically what are you looking for?? (Besides a manual.) I have looked in Clevite ...
Fuel problems	4/15/2007
Q: For some reason I was driving my 1988 Chevy s10 and it popped 3 or 4 times then shut off. When I try ... A: Trevor, Please let me preface this reply that I'm a Parts Professional, NOT a tech but I will ...
2003 Chevy Cavalier	4/15/2007
Q: I have a 2003 chevy cavalier that has apprx. 80,000 miles on it. At 70,500 miles we had to replace ... A: Lindsay, Please let me preface this that I'm a Parts Professional, NOT a tech. I do have some ...
1990 pontiac grand prix starting problems	4/14/2007
Q: have replaced numerous sensors, read the chilton books, toured the forum sites, and am now totally ... A: Ward, Remember I'm just a dumb ass Parts Professional, NOT a Tech. Do NOT disconnect the ...
Not starting	4/12/2007
Q: I am wondering what is wrong with my 1997 Jimmy 4wd. It is cranking but not turning over. I changed ... A: Theo, Just like the previous question I had with a similar problem, is there gas in the tank? Is ...
1990 pontiac grand prix starting problems	4/11/2007
Q: have replaced numerous sensors, read the chilton books, toured the forum sites, and am now totally ... A: Ward, WOW, you have done an extensive amount of work on this vehicle. I MUST tell you I'm a Parts ...
factory vehicle anti theft	4/9/2007
Q: I have already had my computer replaced once to try and fix this problem. The factory vehicle anti ... A: Amie, You are really challenging my ability here. I have no idea how much it would cost to reseal ...
factory vehicle anti theft	4/8/2007
Q: I have already had my computer replaced once to try and fix this problem. The factory vehicle anti ... A: Amie, I hope that fixes it. Water on the computer Can't Be Good!! If, when you replaced the old ...
factory vehicle anti theft	4/8/2007
Q: I have already had my computer replaced once to try and fix this problem. The factory vehicle anti ... A: Amie, Wrecked?? Who knows what is going on then. Did you try backing it down your parent's ...
1984 gmc jimmy wont start	4/7/2007
Q: A friend of mine has a 1984 gmc jimmy with a 4 cyl engine. she said it was getting hot ( not near ... A: David, A few things I need to say. First, I'm a Parts Professional, NOT a tech but I will ...
factory vehicle anti theft	4/7/2007
Q: I have already had my computer replaced once to try and fix this problem. The factory vehicle anti ... A: Amie, I'd try backing the car down the driveway and leave it for a few beers. This is IF the ...
installing a alternator in a 85' cadillac sedan	4/6/2007
Q: How do you install a alternator in a 85' cadillac sedan deville? A: Kendrick, I have a Motor's Repair Manual that goes up to 1989 and all it says is "remove ...
factory vehicle anti theft	4/5/2007
Q: I have already had my computer replaced once to try and fix this problem. The factory vehicle anti ... A: Amie, As I stated in my profile, I'm a Parts Professional, NOT a tech but have been having ...
holdens	4/4/2007
Q: who are the pioneers of ford and holden A: Amy, Where in this World are you?? It seems you might be in Australia..?? Anyway, here we go.. ...
1999 Chev Blazer cuts off	4/4/2007
Q: I have a 1999 chevy blazer that cuts off repeatedly when making only right turns. I have to put it ... A: Candy, I MUST preface this with my Profile... I'm a Parts Specialist, NOT a tech. Okay?? I am not ...
engine repair	4/3/2007
Q: what are the symptoms for water pump failure A: Melvin, May I preface this answer with this: I'm a Parts Professional, NOT a tech but here we ...
Antifreeze leak to the intake gasket...	4/2/2007
Q: I have a 2003 Pontiac Grand Am GT with ~78,000 miles. In my opinion, this car has been nothing but ... A: Please note that in my "profile", I'm a Parts Professional, NOT a tech but will offer these ...
1996 s10 blazer rear differential interchangability	3/24/2007
Q: Might you know if the rear differential in a 1996 4wd, auto s10 blazer is unterchangable with a 1994 ... A: AUTIMN, I will begin this answer with these words of advise. A 4x4 Chevy little truck is known as ...
1994 mazda 626 not going into gear	3/22/2007
Q: i have a 1994 mazda 626 lx automatic. In december i drove it from alabama to texas and back 4 weeks ... A: Gina, I'm sorry to take so long to get back with you. There has been a death in the family and we ...
91 Buick	3/21/2007
Q: What is the firing order of the spark plugs on a 1991 6 cyl. Buick Park Avenue. A: Antoinette, Please let me preface this: I'm a Parts Professional, NOT a Tech but I will give it ...
97' saturn 1.9Liter 16valve DOHC	3/20/2007
Q: is this engine good enough to call it a sports car if yes may have some facts about this make A: Frank, This could really open a can of worms. Personally I like American V-8, no substitute for ...
1998 Lincoln Navi	3/19/2007
Q: I cant find the air compressor relay. do you know where it is? A: Rahiem, Air Compressor Relay...??? Do you mean the Air Conditioner Relay or the Air Ride ...
Ignition stuck?	3/19/2007
Q: okay I have a 2000 Ford F-150 no 4wd. I went to start it up and stuck my key in and nothing the key ... A: Cheryl, Your mail is not very clear but what I'm getting is the key will not turn. Is this ...
differential in a 1995 S10 4X4 pickup	3/19/2007
Q: How do I repair the seal in the axle of the front differential of my 1995 Chevy S10 4X4 pickup? A: John, I'm not qualified to answer this question but have a thought I would pass along to you. If ...
Dodge Stratus shutting off	3/17/2007
Q: I have a '04' Dodge Stratus that when coming to a stop or just accelerating will constantly shut ... A: William, I will tell you up front I'm a Parts Specialist, NOT a tech and am NOT qualified to give ...
ignition?	3/16/2007
Q: When I tried to turn my car off the key wouldn't turn. It's like its locked. I finally had to ... A: Blair, Please let me preface with this: I'm a Parts Specialist, NOT a Tech. Okay?? With that ...
???	3/12/2007
Q: how do i change the timeing change on a ford taurus sho 94 A: Derrick, If you look at my profile, I'm a Parts Specialist, NOT a Tech but I will try to help ...
98 chevy dually	3/12/2007
Q: my 98 gm 3500 7.4 floods usually when im tryin to start it i took it to a gm dealership and they ... A: Jimmy, Please note in my biography, I'm a Parts Specialist, NOT a tech. I work in a parts store ...
88 ford tarus	3/8/2007
Q: I've a 88 ford tarus with a 3.0 engine that recently had new heads put on. Everything was torqued ... A: Will, You don't tell me if it is an OHV engine or DOHC engine. The 3.0 was offered in both ...
my 94 chevy blazer	3/6/2007
Q: i have a 94 chevy s10 blazer 4.3 vortec v6, the problem i having is every morning i can start up my ... A: Charlie, If you look at my profile, I'm a Parts Specialist, not a Tech but I will offer my ...
Turn Signal Relay 94 Bonneville	3/5/2007
Q: Is there one and if so, where is it? A: J., I am a Parts Professional and have been for 34 years and have NEVER heard of a turn signal ...
mercury	3/3/2007
Q: 1999 Mercury mini van villager code scanner said bad knock sensor had to pull plenum off to get to ... A: Jaymes, AlData and Mitchell on Demand offer such diagrams but you have to "join the club" to gain ...
ignition switch for 1989 Lincoln Town Car	12/17/2006
Q: My car will turn over and attempt to run, but will cut off when I release the key from start ... A: Ken, I'm a Parts Professional, NOT a Tech but here goes.. I agree with you. It does sound like ...
Wrong BCM installed 1998 caravan se	12/17/2006
Q: I installed a scrap yard BCM on my 1998 Caravan SE, 3 litre. My original BCM is 4801062AE VIN ... A: Bob, I would like to preface my opinion with this thought. I'm a Parts Professional, NOT a Tech, ...
headlights	12/16/2006
Q: When turning on my lights the parking lights comes on but the headlights do not unless I wiggle the ... A: Lynn, You don't state what year and type of vehicle but I'd guess the headlight switch is bad. It ...
1994 Pontiac Bonneville	12/15/2006
Q: My son says that he was making a left hand turn and the engine cut out. It started right back up ... A: Deborah, No, I don't think your alternator is going out. As far as determining what caused the ...
fuel pump	12/14/2006
Q: A: Mike, The pump is supposed to mounted in rubber to eliminate any audio noise. There is a ...
kia	12/13/2006
Q: how do i remove a/c belt on 1997 kia sephia thank you A: Mike, I am NOT qualified to answer your question but will offer this information. If you go to ...
1995 lincoln continential	12/9/2006
Q: the car is front wheel drive and the humming was there before i changed the tires i was told maybe ... A: Gary, If you can find a shop that has a "spin on the car" balancer, you can do the following. ...
1995 lincoln continential	12/8/2006
Q: have a 95 lincoln with new pads and rotors all the way around, I also put new tires all the way ... A: Gary, I'm a Parts Professional, NOT a Tech but I will offer these thoughts for your ...
ignition	12/8/2006
Q: i have a 1995 dodge intrepid when i turn off ignition engine continues to run . does this mean my ... A: Dean, I am a Parts Professional, NOT a Tech but I will offer my thoughts for your consideration. ...
Three Speed on the Column	12/6/2006
Q: What year and model of vehicle was the last one to be available with a "Three on the Tree"? Thanks, ... A: John, HOW OLD ARE YOU??? Do you know how long it has been since I heard the phrase "Three on the ...
2003 GMC Sierra	12/5/2006
Q: When I come to a stop, or slow to a speed bump or even try to do a u-turn, the engine slows to a low ... A: John, I am NOT qualified to answer this question but when I joined this group, I vowed to offer ...
truck box	12/4/2006
Q: Looking for a long box for a /66 3/4 ton Chev. S20 p/u Needs to be in good enough condition so we do ... A: Donna, I have been in the parts business for 32 years and have never heard of a 1966 3/4 ton S20 ...
clicking noise from starter	12/4/2006
Q: my 1985 plymouth horizon wotn start...when i jump the battery, the car will start and run but once i ... A: Simone, Please note I'm a Parts Professional, NOT a Tech. Okay?? I will give you my thoughts but ...
91 lincon towncar wiper motor relay	12/1/2006
Q: I work at a small dealership in idaho and i am working on a 91 towncar and i can not get the wiper ... A: Scott, I am NOT qualified to answer this question but when I joined this group, I promised myself ...
1990 Ford F250 7.3L idle/stall	11/30/2006
Q: I own a 1990 Ford F250 7.3L n/a automatic diesel 4x4. We have just recently experienced very cold ... A: Justin, Let me begin by saying I'm NOT qualified to answer this question. I'm a Parts ...
fuel filter location	11/28/2006
Q: I have a 1986 buick century statewagon and cannot locate the fuel filter, can you help me with this? A: Ron, I'm a Parts Specialist, NOT a tech but they would need this information also. What size ...
Radiator electric fan controller	11/25/2006
Q: I want to install a blower (12 or 24V) to supply cooling air to small (8KW) diesel powered generator ... A: Leons, First, I'm an Auto Parts specialist. This question would be better suited to someone who ...
CAR WONT START	11/25/2006
Q: MY CAR WILL START AND RUN FINE WHEN I JUMP IT OFF, BUT WHEN I TAKE THE CABLES OFF IT DIES RIGHT ... A: Johnny, Please remember I'm a Parts Specialist, NOT a Tech, Okay?? It could be either the ...
fan switch 1992 gmc sonoma	11/24/2006
Q: my fan stopped working so I replaced the fuse, no luck So i replaced the fan, still no luck then I ... A: Vin, I'm a Parts Specialist, NOT a tech but I will give you my thoughts on this one. Please ...
2004 chevy impala front end noise	11/22/2006
Q: i have an 04 impala with 46,000 miles on it. just recently the front end has been making a mild ... A: Richard, Sorry for the delay, today is Thanksgiving... Please remember, I'm a Parts Specialist, ...
upper intake manifold gasket	11/14/2006
Q: I have a 2002 grand prix with the 3.1L v6. I am have antifreeze loss and a Code P0401 (low EGR ... A: Jeremy, Sorry to take so long to respond but I'm a Parts Specialist, NOT a tech. In my Bio, I put ...
Radiator Pressure	11/11/2006
Q: I have a 89 Ford Probe that I am having problems with the cooling system. There is too much ... A: Jeff, You give me NO repair history except you probably have replaced the two hoses. Obviously it ...
94 lincoln contenential odb connector location	11/11/2006
Q: do you where the odb connector is located on a 94 continential? I have looked everywhere A: Rich, Sorry to take so long but I was off work over the weekend. I checked today and the OBD port ...
1994 Ford F150- Stalling problem	11/7/2006
Q: To start off, this truck is in mint condition with 80,000 well taken care of miles. It is 4 wheel ... A: Mike, I'm so very sorry to take so long to respond but I have been just getting my butt kicked at ...
signal/hazards	11/6/2006
Q: what's going on here.... I have a 1986 winnebago and the signal lights work all around. when I turn ... A: Adam, When I signed up for this group, I put in my description that I'm a Parts Specialist, NOT a ...
- - -	11/5/2006
Q: i had put a gallon of coolant in to the car and after 2 hours it was all gone i then put another ... A: Gerardo, I'm a Parts Specialist, NOT a Tech but here are my thoughts... Obviously you need to ...
2004 ford mustang 4.6L GT	11/5/2006
Q: I got and engine service light. took it to ford. i got two codes. P0102 - which is the MAF (mass air ... A: CJ, I'm a Parts Specialist NOT a Tech but I sell High Performance add on's. Stop right here. ...
94 chevy blazer wont start	11/4/2006
Q: Is there a quick fix to get it started, screwdriver to the solenoid, or anything? It has power but ... A: Anthony, You haven't given me much to go on as far as what tests you have performed, if any. ...
1998 ford exploer	11/4/2006
Q: my heater only blows cold air what could be the problem A: Mike, I'm a Parts Specialist, NOT a Tech but will offer these thoughts. The first thing that ...
Temp Gauge Problems	11/1/2006
Q: One thing I have to add and maybe this will nail it..? I had to drive my car today(only about 25 ... A: Deniese, I'm sure you have checked the coolant since you sent me this message? Was it low? It ...
Temp Gauge Problems	10/30/2006
Q: I have a 1991 Plymouth Acclaim that was giving to me by an elderly man. 65,000 Miles only. I have ... A: Deniese, This problem could have a few possible causes. First you need to determine if the ...
my 1996 chevy astro stop running ?	10/29/2006
Q: my 1996 chevy astro stop running one day , i changed the alternator because it was makeing noise ... A: Robert, When I joined this group, I vowed to attempt to answer ALL questions. I'm a Parts ...
location of pvc valve and how to change it	10/28/2006
Q: i am a beginner at engines and trying to learn to change parts on my own . i have a 96 grand am and ... A: Thomas, The VERY first thing you need to learn, if you are going to work on cars is to give the ...
1000rpm	10/28/2006
Q: I have a 1995 oldsmobile aurora that runs great, but idles low in drive at 500rpm. In park it idles ... A: Vincent, I'm a parts specialist, NOT a tech but I have done some checking with people I sell ...
brake system	10/26/2006
Q: I drive a 99 olds alero. I had new brakes put on and about a month later anytime I start my car my ... A: Christy, I decided, when I joined this organization, I would answer ALL questions. Even if I ...
drive line vibration	10/25/2006
Q: while accelerating when RPMs start getting high it has a vibration it also does it when i kick in ... A: Scott, I don't know how I missed this question. It didn't come into my mail box like it should ...
1983 ranger 2.0 timming	10/24/2006
Q: i got an old 83 ranger that the head gasket went on and i forgot to make marks on the cam gear crank ... A: Mike, Okay, here is what Mitchel on Demand has to say... Align camshaft sprocket timing mark ...
Exhaust	10/24/2006
Q: I have a 94 3000gt that has an after market exhaust. I have a problem with the exhaust smoking when ... A: Collins, I'm a parts specialist NOT a tech but I will offer my thoughts. Blue smoke is oil, ...
alternater problems	10/18/2006
Q: I've had two alternates installed in my 1999 Yukon and they both have failed the only work I've had ... A: Greg, I'm a Part Specialist, NOT a tech but I would guess the stereo is putting too much drain on ...
1985 Ford F250 replacing the Ingition actuator	10/17/2006
Q: I'm trying to replace the ingition actuator on an 85 ford f250 w/ crusie control and tilt, but I'm ... A: Javier, I'm a Parts Specialist, NOT a tech but I can tell you that there are a couple places you ...
TRANSMITION	10/17/2006
Q: I own a 99'Malibu w/127000k mi.VERY well taken care of!About a month ago my tranny started slaming ... A: Amber, Without knowing which transaxle you have, I'm just giving you my $0.02. I'm a Parts ...
about a 2000 ford tarus	10/16/2006
Q: my emission light is on and this is hte second time it has come on. i put unleaded gas in it then i ... A: Joyce, There are quite a few things that could cause this light to be on. Depending where in the ...
95 Buick Park Avenue Hesitation	10/12/2006
Q: I recently replaced spark plugs and wires on my 95 Buick Park Avenue, also put in a new battery and ... A: Denise, I will tell you up front that I'm an OLD PARTS SPECIALIST. I have been on a parts counter ...
HEATING AND COOLING CONTROL FOR 1991 LINCOLN TOWNCAR	10/12/2006
Q: BUT YOU HAD TO GO UNDER THE DASH TO DO IT TO PUT THE PART IN SO WHAT I WANT TO KNOW IS WHAT PART DO ... A: James, It sounds like a diverter door or the vacuum pod that operates it is bad. It could also be ...
ABS system	10/12/2006
Q: I have a 1997 Mercury Cougar XR-7. My ABS light is on. When I brake my car wants to move left. ... A: Jose', Firstly I'm sorry to take so long to respond. I had a small medical emergency and have ...
2002 GMC Sonoma heating problems.	10/11/2006
Q: My 2002 sonoma has no heat. I have a new heater core and a new thermostat. All modes work on heat, ... A: Marty, Firstly let me explain 2 things. I'm sorry for taking so long to respond. I had some ...
turn signal malfunction	10/10/2006
Q: I have a chevy impala 2000 and have 2 questions. First the turn signals are not functioning at all ... A: Coleen, I'm a Parts Professional, NOT a Mechanic but I can't just ignore your questions. I do ...
Brake lights	10/9/2006
Q: I have a 1996 Mitsibishi galant and the brake lights are constantly on while the car is off and they ... A: Marvin, I'm Parts Specialist but will give you my thoughts. Firstly, I'm confused about your ...
wiring harness	10/7/2006
Q: i will get those part tuesday. yes it is all original. ford dealership here did a nationwide ... A: Michael, Like I said, be sure to talk to someone who KNOWS WHAT IS GOING ON!! I can't emphasize ...
wiring harness	10/7/2006
Q: i cant locate a wiring harness for a 1984 ford f-350 crewcab dually, 460 gas, auto trans, dual fuel ... A: Michael, I may be able to help on some or all of this but what I need YOU to do is go down to ...
brake light out 1997 Lincoln Continental	10/6/2006
Q: How do I replace the brake light on the 97 Lincoln continental. I looked up the number of the bulb ... A: Bob, First, let me tell you I'm a Parts Specialist, NOT a Tech!! I have told this to AllExperts ...
Three Speed on the column	10/5/2006
Q: Why did they stop making cars with three speed on the column? I used to drive a ford or chevy ... A: Scoe, Hey, how is it going?? I enjoy driving a stick also but the old 3 speed just became a ...
Low oil pressure	10/1/2006
Q: I have owned a 1991 Buick Park Avenue Ultra since new and have always used Mobil One oil in this ... A: John, Please bear with me for a minute, Okay? I'm a Parts Professional, NOT a Tech or Mechanic. I ...
pvc valve	10/1/2006
Q: where is the pvc valve located on a 1987 cougar.My husband said it is a fuel injected, 3.0, V8 A: Betty, Well, we have a problem. An '87 Cougar only had a 3.8, nothing else but I think it is a ...
Key for an old car	9/30/2006
Q: I ned a key for a 1970 dodge challenger all I haVE AT THIS POINT IN THE VIN. CAR HAS NOT RAN IN ... A: Kevin, If the car doesn't run, why do you need a key..?? Sorry. Parts men humor. I couldn't ...
No brake lights	9/29/2006
Q: I have a 1993 chevy Astro Van and I have no brake lights. Turn signals and park lights are working. ... A: Tamika, Please allow me to preface this with a statement. I'm a Parts Professional, NOT a Tech or ...
1998 Ford Navigator air shocks replace or repair	9/29/2006
Q: The shocks on my 1998 Ford Navigator is low like a low rider, Do i put air back in or do i replace ... A: Cleve, First let me tell you that a Navigator is made by Lincoln. The only reason I say this is ...
trans mount or engine?	9/29/2006
Q: well at this time i don't know trans from engine mount iam talking about the pass side i called it a ... A: Clickie, I appreciate your giving me the OEM number. It doesn't help, however. This is a tough ...
looking for 86 cad-eldo r.h. trans mount	9/28/2006
Q: i have a trans mount and bracket broken in a 86 cad-eldo the dealer says 161.00 and i think someone ... A: Clickie, I looked in an Anchor/Doan Catalog at a Caddy 4.1 engine in an Eldo and the transmission ...
basic maintenance	9/24/2006
Q: hey skip, I own a 2002 chev cavalier z24 with a 2.2 ecotec enigine. Ive looked all the over the ... A: Yo Rob, Open the hood. Up by the radiator you will see the air intake. To the right of that, you ...
89 stang	9/22/2006
Q: need to find timing marks . iknow 1o degrees BTDC, but were do u line them up to. also i heard i ... A: Nino, I'm having a hard time not being critical of your request. I think I understand what you ...
please help me asap	9/22/2006
Q: im trying to find out where the water pump is located on my 1996 plymouth neon and if the motor has ... A: Heather, I am a Parts Specialist, NOT a tech but I will give you my thoughts about this. Your ...
Electrical Problems	9/21/2006
Q: I was just in to the garage to have my gas tank replaced on my 1997 Sunfire GT. At that time ... A: Beth, Please let me preface this opinion by telling you I'm a Parts Specialist, NOT a Tech. But I ...
1991 ford taurus SHO	9/20/2006
Q: but it should still run and it does if you spray gas in the intake. the fuel pump does not come on ... A: Vaughn, This is WAY out of my realm of expertise. I'm a Parts Specialist, NOT A TECH. I will ...
problem with car	9/19/2006
Q: i have a 1988 volkswagon fox GL the engine stalls while idling, engine stalls while driving, vehicle ... A: Mitchell, Wow,,, this is like calling the Dr. and saying "My elbow hurts, what is wrong?" It ...
2000 M.P.G. Engine	9/17/2006
Q: Somebody who evaluates cars for a living told me that there exists an engine that can give someone ... A: James, This is WELL out of my range of expertise but I feel compelled to give you an opinion. IN ...
Bleeding a Ford F250 engine	9/16/2006
Q: What steps are involed in bleeding the engine on a Ford diesel F250 engine? A: Peter, Bleeding is a term used on brake systems. What system are you trying to bleed and why?? ...
Custum cars.	9/14/2006
Q: Dell computer are known for making custumized computers and are order first and received later on. ... A: James, There is a phrase in racing. It is "Speed costs money, how fast do you want to go?" The ...
1986 monte carlo	9/6/2006
Q: when i turn on my heat i see vapors from burning radiator fluid and sometimes when niether the heat ... A: Philip, I have told the kind people at All Experts I'm a parts professional, not a tech but your ...
Location of PVC valve	8/29/2006
Q: I wanted to know the location of the PVC valve on my 2002 Mercury Sable. I have been searching for ... A: Marc, I am a parts expert, not a Tech. I have tried to explain this to All Experts but I keep ...
Replacing transmission fluid	8/19/2006
Q: My little brother accidentally drained my transmission fluid while attempting to change my oil. My ... A: Mindy, Usually on manual transmissions & transaxles (which you have) the fill plug is about 3-4" ...
Intake Gasket chevy 3.1 v6	8/15/2006
Q: My 1995 Chevy Beretta Z26 is leaking oil. We believe its the intake manifold gasket. I am looking ... A: Brandon, Give me a fax number. I have printed out instructions on how to remove the intake. There ...
brakes	8/11/2006
Q: I recently purchased a used Volvo S60 year 2000 model with only 10,000 miles. The brakes work fine, ... A: Jerry, Sorry to take so long to get back with you. Our kids are home from college for a week and ...
Fuse Panel	8/9/2006
Q: I have a 93 Taurus SHO, I cannot find the owners manual for it. I would like to know if you would ... A: Guy, Sorry to take so long to respond but MY car broke down last night while my kids were driving ...
2000 ford expedition	8/9/2006
Q: I have a 2000 XLT Ford Expedition and the abs light comes on and stays on. When I first start the ... A: Chris, I'm so sorry to take so long to respond. My kids are home from college and THEIR car broke ...
2002 tahoe z71 flex 5.3l	8/8/2006
Q: My steering clunks or knocks at slower speeds turning left or right ive seen some tsb's about the ... A: Andy, I'm a parts professional, not a tech. Let me print out your information and take it to work ...
2002 tahoe z71 flex 5.3l	8/8/2006
Q: My steering clunks or knocks at slower speeds turning left or right ive seen some tsb's about the ... A: Andy, What do the Technical Service Bulletins say the problem could be?? Traditionally, if a ...
Check engine light/car shakes then shuts off	8/7/2006
Q: I have a 2001 Nissan Altima. I went to get an oil change and the check engine light was on. Whenever ... A: Janelle, Take a chill pill. It's a car, not a child. Number 4 plug was bad but what caused it to ...
ford focus fuel filter location	8/2/2006
Q: Where is the fuel filter located on a 2002 ford focus? A: Brandon, The fuel filter is located back by the gas tank. It is a round filter with 5/16" nipples ...
Taurus over heating	7/31/2006
Q: I just had a new radiator, cap, complete engine rebuild, new thermostat and water pump about 1 month ... A: Brian, Let me preface my answer with this statement. I'm a parts professional, not a repair tech. ...
'96 Continental Air Suspension	7/29/2006
Q: the system is dead. can you help me troubleshoot it for ckt breakers/fuses and how to find possible ... A: Dave, This question is for a repair tech and I'm not. I locate antique/obsolete auto parts but I ...
2003 buick park ave	7/19/2006
Q: I have a 2003 Buick park ave w/approx 50k miles. As I am driving (about 60mph on the local highway) ... A: Tonya, I'm a parts expert, not a mechanic. I'm still trying to figure out how I ended up in this ...
Ac not working	6/23/2006
Q: Followup To Question - I own A 98 GMC YUKON The Ac is not working. Checked fuses and relays good. ... A: Ravuth, I don't have a diagram of the wiring for that vehicle. I am an old parts guy that has ...
Ac not working	6/22/2006
Q: I own A 98 GMC YUKON The Ac is not working. Checked fuses and relays good. Jumped pressure cycling ... A: Ravuth, It is obvious you have no voltage to the clutch via normal GM wiring. How did you check ...
Ac not working	6/20/2006
Q: I own A 98 GMC YUKON The Ac is not working. Checked fuses and relays good. Jumped pressure cycling ... A: Ravuth, A couple of things come to mind. Firstly, did you jumper the proper switch? I'm not ...

All Questions in This Category