| Subject | Date Asked |
|
| 1987 chevrolet caprice | 9/29/2008 |
Q: 000 miles on it. lately, on occasion, when I start the car it shakes, however, after driving it a ...
A: your choke may need ajustment..may be closed afer warm up..also if the idle is too fast t will be ...
|
| Chrysler concord 1998 not starting | 9/27/2008 |
Q: I am getting spark and fuel but it want start unless I put either to it then it will stay running ...
A: yes the crank sensor could do that...if you can scan your computor it sould tell you what the ...
|
| firebird timing | 9/27/2008 |
Q: I recently bought a 1999 Firebird with a 3.8 engine. My brother and I are trying to fix it up . WE ...
A: there is a computer disconnect wire..disconnect then set timing on 0 degrees... reconnect the ...
|
| what thermostat should i use for an 1981 chevy 350 motor | 9/6/2008 |
Q: what thermostat should i use for an 1981 chevy 350 motor? it runs fine in slower traffic, but gets ...
A: Try a 185 thermostat. be sure your fan clutch is in good shape and no leaks in the cooling system.. ...
|
| Lexus car | 9/6/2008 |
Q: My car failed a SMOG test.The EGR Failed.What is an EGR? Many thanks Art.
A: EGR is exaust gas reciculation.. there is a EGR valve on your engine.. It may need replacement or ...
|
| 1997 mercedes c230 | 9/5/2008 |
Q: I am trying to fill my auto with R134a aircondition. I do not know were it goes. The Manuel for ...
A: Low low pressure inlet valve is located on the larger diameter hose.. PLEASE VISIT MY EBAY STORE ...
|
| 1979 GMC pick-up truck fuel pump 350 V-8 | 8/29/2008 |
Q: How do you check the fuel pump on this truck? With everything turned off (ac/heater blower, radio, ...
A: a 79 chevy should have a mechanical fuel pump located on the passenger side of the engine.you cannot ...
|
| Brake Light | 8/26/2008 |
Q: When I start driving my brake light comes on. Then when p/u is turned off and re-started its off ...
A: 2 things you can do.. first make sure the parking brake switch isnt making it go on.. pull and ...
|
| dashlights | 8/25/2008 |
Q: I have a 94 chev.1500,when I turn on the headlights, the dash lights go out.I have checked the ...
A: check the adjustment in your dimmer switch... that might be it... rc PLEASE VISIT MY EBAY STORE FOR ...
|
| alternator | 8/24/2008 |
Q: my girlfriend has a 1997 suzuki esteem. the car would'nt start so i jumped her off. well 5minutes ...
A: Check your alt belt first if its too loose it will not charge up.. also be sure your battery cables ...
|
| gasket problem | 8/24/2008 |
Q: I drive 1996 chevrolet Lumina 3.1 V6. It has been leaking a little coolant and I have been adding ...
A: it is you intake manifold gaskets..a common problem on that engine.. have your radiator flushed and ...
|
| intake | 8/20/2008 |
Q: I have a 1996 Ford Explorer. I hear a vacuum/whistling sound that is coming directly from the ...
A: Look for broken or cracked vacuum lines or bad egr or pcv valve. good luck. RC PLEASE VISIT MY EBAY ...
|
| replace water pump 2004 gmc envoy | 8/20/2008 |
Q: i am having trouble removing the fan clutch from the water pump. HELP!!!!
A: usally i remove the van first..the belt will hold the pully still..you may have to hit the wrench ...
|
| truck burning oil | 8/17/2008 |
Q: my truck justr recently startred smoaking alot and blowing BLACK oil out the tail pipe and the oil ...
A: The oil gauge measure oil pressure..not oil level check your dipstick again..if its too full it will ...
|
| charging a/c on 1981 toyota pickup with a 22R engine | 8/3/2008 |
Q: I see both ports but can't tell which is which. Can you help please?
A: The larger diameter hose is the low pressure side. thats where you charge the system from.. PLEASE ...
|
| 71 Firebird 350 transmission trouble | 7/26/2008 |
Q: I am restoring a 71 firebird that sat for 9 years until now. When I drive it for more than 15 ...
A: Before you do any major repairs.. change your AT fluid and filter. also replace the vacuum module on ...
|
| starting problems | 7/22/2008 |
Q: I have a 2002 Land Rover Freelander, and it will not start. In May I had the intake plenum, manifold ...
A: Yes ..ethier your battery is no good or the charging system is not charging.. charge the battery.. ...
|
| replace 2002 nissan frontier water pump, 3.3 liter v6 | 7/22/2008 |
Q: If I follow the Haynes book for water pump replacement, can I do the job myself instead of having it ...
A: Im sure you can if you have tools... its not to difficult if you take your time.. good luck. RC ...
|
| 1996 RS Camaro | 7/22/2008 |
Q: I have a Camaro with a 3800 Series II (V6, 3.8L.) engine it sounds like an aluminum banging sound. ...
A: try running 20/50 oil and see if that helps those engines are common for lifter failure.. if it ...
|
| Dorango Disk Brakes | 7/18/2008 |
Q: Last night I removed the front calipers on my 2003 durango in an effort to replace the pads (and ...
A: Yes you have to remove the torqe screws.. Whw you put it back together..install the rotors ...
|
| 1998 ford explorer | 7/10/2008 |
Q: I HAVE A 98 FORD EXPLORER MY AC DOES NOT WORK BUT MY HEATER DOES?? IS THERE A FLUID I CAN PUT IN MY ...
A: You came to the right place. I sell R12 system refill kits. Any of my Maxi kits w/R12 adaptors will ...
|
| 2001 venture a/c not working | 6/26/2008 |
Q: We recently recharged our a/c unit and then it all started to leak out. My husband thought it might ...
A: you must check te fron pressure with gauges.. if it is low or empty..add some freon with green dye ...
|
| bmw | 6/21/2008 |
Q: what does it mean if im getting a jerk when i apply breaks to my 2003bmw 325ci ANSWER: pulsating ...
A: FIGHT THE RISING PRICE OF GASOLINE HERE ARE SOME TIPS FOR ALL OF US TO USE TO SAVE $$ ON FUEL ...
|
| bmw | 6/21/2008 |
Q: what does it mean if im getting a jerk when i apply breaks to my 2003bmw 325ci
A: pulsating brakes are common on BMW and MERCEDES.. It means your brake rotor disks are warped.. Dont ...
|
| 69 firebird | 6/20/2008 |
Q: i have a 69 firebird with a pontiac 350 engine(2 bbl carb)the problem is on intake manifold.the two ...
A: It is more than likly exaust leak.. when you change the intake manifold gasket.\ Put heat ...
|
| fuel type | 6/19/2008 |
Q: I just bought a 2003 Infinity G35 coupe automatic. It reccommends that i use priemium fuel. Is it ...
A: i think i would be safe to use regular. it wont harm anything.. RC PLEASE VISIT MY EBAY STORE FOR ...
|
| Front end alignment | 6/18/2008 |
Q: I just had my half axles replaced on my 1985 Honda Civic wagon and was told to get a front end ...
A: yes..a good alignment man should have centered the wheel for you.. also..try rotating your tires ...
|
| 1998 silverado ac system | 6/16/2008 |
Q: how much do I put in?
A: I use ester oil most of the time. You can buy small bottles or up to 8oz. i do deal in ac kits.. ...
|
| Brake bleeding... | 6/16/2008 |
Q: I have a 1984 Chevy G20 van with a 305/5.0L. It blew some brake lines the other day, the two that go ...
A: yes..try bleeding the MC at the lines.. pump up the pedal..then bleed..all at once first couple ...
|
| Big block Chevy overheating | 6/7/2008 |
Q: I have tried EVERYTHING to prevent my 454 big block from overheating at any rpm idle or highway ...
A: i would try retarding the timing 2-3 desgrees to 7-or 8 at idle build air flow panels one each side ...
|
| 2001 chevy venture | 6/5/2008 |
Q: I was told that the lower intake manifold gasket needs replacing.The mileage is 59,560.When i was ...
A: if coolant floods you oil system and you continue driving it.. it could ruin yout main and rod ...
|
| 1994 Olds wheel bearing | 6/2/2008 |
Q: I have a 1994 Olds 88 which has a growling noise in the right front area of the car when moving. If ...
A: yes..i agree..sound like a bad wheel bearing to me.. if i remember correctly. the hub and bearing ...
|
| 92 Chev Blazer HELP! | 5/29/2008 |
Q: Greetings Ron... How are you doing? I'm about to leap off a building with this Blazer issue. SPECS: ...
A: You might try spraying WD-40 on all of the shifter linkage joints.. and try working it loose engough ...
|
| Coolant Hose Leakin Under Manifold | 5/24/2008 |
Q: I have a 94 Mercury Grand Marquis. I took it to Mercury to have it looked at because it will not ...
A: if it is a 3.0 or 3.8 you may be able to replace the hose without taking it completely apart. the ...
|
| No power to igniton | 5/21/2008 |
Q: I have a 1987 Komfort RV 454 Engine. Started RV ran a few minutes and stalled. Tried to restart ...
A: LoOk for a fusable like wire that may have burned off. Many GM products have inline fusable links ...
|
| Front end alignment specs | 5/20/2008 |
Q: When buying tires recently, the shop called and said I needed an alignment, and I authorized them to ...
A: normally toe ie measured by inches not degreees.. most trucks should be toe in 1/8" or less. camber ...
|
| Milky coolant, oil leak, and vibrating during braking | 5/17/2008 |
Q: I own a 1995 Mercury Cougar with a V8 engine, and have 3 current problems. 1. I had an oil leak for ...
A: your brakes vibrate because your rotors are warped you need to do a brake job anfd either replace or ...
|
| plymouth sundance | 4/28/2008 |
Q: i have a 1988 Plymouth sundance 2.2 4 cylinder engine and i just replaced the water pump and timing ...
A: better double check your timing markrs and set your distributor timing again.. if the crank and cam ...
|
| Vinbration in driveline/ 92 4X4 Yukon | 4/26/2008 |
Q: I have recently developed a really noticeable vibration, in my 92 GMC Yukon. It seem to be coming ...
A: yes i would check the u joints for sure... i bet thats the problem.. good luck. RC PLEASE VISIT MY ...
|
| Brake problem w/ my 1994 Chevy Z71 | 4/25/2008 |
Q: My parking brake light is on all of the time now and when I drive then apply the brakes it feels as ...
A: Sounds to me like your rear brakes need a looking at. May as well check all 4 wheels.. They may be ...
|
| ml 420 a/c | 4/20/2008 |
Q: The Mercedes ML 420 that I bought in Nov in Buffalo has an a/c problem. Since it defrosts fine, I ...
A: You are luck to send to me. i happen to deal in A/C recharge kits Please visit my ebay store.. If ...
|
| u joint vibration | 4/11/2008 |
Q: I own a 99 chevy Z71, I installed 2 new u joints in the rear driveshaft and only indexed the rear of ...
A: i doubt thats the problem. make sure the u joints are centered and the clips are still in place... ...
|
| air conditioning compressor wont stay on | 4/4/2008 |
Q: i have a 1998 cadillac eldorado,4.6L, automatic i get a message in the drivers info center that ...
A: Double check your freon pressres your low side pressue must not drop lower than 25psi while revving ...
|
| main bearings | 3/23/2008 |
Q: I have to do a engine rebuild on the vehicle. I replaced my main bearings. Now I read online that I ...
A: PLEASE VISIT MY EBAY STORE FOR AUTOMOTIVE REPAIR “HOW TO” DVDs ENGINE REBUILD DVDs ONLY $9.99 AND ...
|
| 2002 mercury 8 cyl./oil on spark plugs | 3/19/2008 |
Q: Ron, Good afternoon. I saw a decrease in my fuel mileage, so I decided to replace my sparkplugs. The ...
A: The oil is probably coming from you valecover gasket o-rings. The Ford dealer should have told you ...
|
| Eagle Talon Head Bolt Torque Specs | 3/12/2008 |
Q: I have a 1995 Eagle talon 2.0 DOHC Turbo (TSI). I am having some head and valve work done. I ...
A: The new gaskets will not need be retorqued AFTER start up... Maybe during head installation..but ...
|
| spark plugs | 3/11/2008 |
Q: how do you change the spark plug and cables in a 1990 toyota celica st. small engine. thanks ...
A: The oil was from your valve cover orings leaking.very common.. i would try to wipe away any oil ...
|
| Noisey fan on 1993 Nissan Alima | 3/10/2008 |
Q: Every time we turn on the air one of two fans located by the radiator starts running and makes a ...
A: you will have to see if its the fan blade worn out or the fan motor.. maybe its loose?? Shouldnt be ...
|
| Battery Indicator Stays Lightly Lit On Dash | 3/10/2008 |
Q: I have an 1993 Nissan Sentra 1.6 2 door in good running condition with 200,000+ miles.Bought it for ...
A: If tyhe alternator is goos it will put out about 14v at the battery while running. if not you will ...
|
| spark plugs | 3/9/2008 |
Q: how do you change the spark plug and cables in a 1990 toyota celica st. small engine. thanks ...
A: If i remeber correctly the spark plugs are in the top of the motor.. puul the spark plg wire ...
|
| power steering | 3/6/2008 |
Q: How doI bleed the power steering on an 06 Chevy Impala
A: I have never hear of blleding PS system.. But to get the air out.. you mat turn the wheel from left ...
|
| dodge brakes | 3/6/2008 |
Q: I have a 1999 dodge durango. On the way home the rear brakes locked up, I put new wheel cylinders on ...
A: If the line is holding pressure after you relaese the foot pedal... Your Master Clyinder may be ...
|
| 89 chevy 5.7L v8 | 3/6/2008 |
Q: i am trying to do the timing on my 5.7L chevy TBI system engine and have been unable to do so ...
A: did you disconect the computer connection wire before you set the timimng. it must be disconected to ...
|
| Steering | 2/28/2008 |
Q: I have a 1992 Ford Explorer it has become hard to steer properly when driving down the road kind of ...
A: If you adjusted the steering bow a little too tight..it will be hard to turn and not return to ...
|
| 97 ford contour heating up | 2/28/2008 |
Q: i got a v4 97 contour and its got around 120k miles on it. after driving at for about a 100 miles or ...
A: Double check to see if the coolant is full.. Wait untill its coled of to not get burned... Then let ...
|
| rubbing noise | 2/26/2008 |
Q: I have a 92' Grand Marquis, I recently replaced all the breaks on the car and both back rotors ...
A: the ony other idea.. If the pistons dont scre in.. The parking brake shoes may be inside under the ...
|
| rubbing noise | 2/26/2008 |
Q: I have a 92' Grand Marquis, I recently replaced all the breaks on the car and both back rotors ...
A: the rear piston calipers are threaded.you should have spinned the piston to the left and screw it ...
|
| use of synthetic oils | 2/21/2008 |
Q: I just bought a 95 Pontiac Grand Prix, 3.1 M code engine with 40k miles in new condition. I was ...
A: For the most part... Synthetic oils do last longer with less breakdown. but...they do also cost ...
|
| 1994 chevloret pick up | 2/21/2008 |
Q: just bought my son a 1994 chevy silverado 1500 4x4 pickup. had the oil changed. having sudden drops ...
A: Double check your oil dipstick.. Make sure it is full.. Check for leaks.. or.They may have uesed ...
|
| internal engine trouble | 2/20/2008 |
Q: I need to know if i need a valve job ? I have a gmc 2 350 5.7 ltr. and the problem is the hose going ...
A: It is probably not a valve.. you may have a damaged piston or broken piston rings.. that is the most ...
|
| Front Strut Replacement '02 Mazda MPV LX | 2/19/2008 |
Q: My wife complained that our '02 Mazda MPV was feeling every bump and making noise over bumps- took ...
A: often times the link pin bushings will cause noise.. maybe you only need those..they are not ...
|
| fuel pump 79 f100 302 | 2/18/2008 |
Q: After repalcement, looks like the oil needs to be replaced due to old pump leaking internaly. Should ...
A: It should pump immedeatly unless it has been parked for some time. Check for cracks in the fuel line ...
|
| Toyota 1989 22r engine | 2/12/2008 |
Q: Two days ago my truck started running hot out of the blue. I would run it. Stop on the side of the ...
A: you either have a corrded head gasket..or...the timimng chaind has worn a hole thorought the side of ...
|
| Poor Braking performace - GMC Yukon XL | 1/29/2008 |
Q: . I bought a 2002 GMC Yukon Denali XL with about 80K miles.. It's in great shape over all and no ...
A: First try bleeding all the old brake fluid out...that might make a difference..ALSO....sometimes a ...
|
| 1991 SR5 4Runner | 1/17/2008 |
Q: I just got a this from a guy, its running ok atm but theres a bit of a clicking noise constantly ...
A: It is probably the valves ticking..Not to worry . That is common.. Most of those years are not ...
|
| 2003 Pontiac Grand Prix GT | 1/14/2008 |
Q: When I turn my steering wheel I hear a grinding noise on the passenger side front only could this be ...
A: yes, it could be the cv joint..also check the wheel bearings.. Good luck! RC PLEASE VISIT MY EBAY ...
|
| 79 malibu | 1/13/2008 |
Q: I own a 1979 chevy malibu and I would like to know what kind or type of carb to install on a 350 ...
A: that year usally comes with a rochestor quadrajet 4 bbl...you can also fit an edelbrock on there ...
|
| Rough Idle | 1/12/2008 |
Q: I have a 1993 Nissan Sentra with an automatic transmision, and about 90,000 miles. I live in ...
A: check for a broken or loose vacuum hose or bad pcv valve.. thats what it sounds like to me.. Check ...
|
| 1996 Chev. S 10 , 6 cyl. pick-up | 1/12/2008 |
Q: Where is the knock sensor located, and how do I remove and replace it?
A: it should be located on the cyinder head..it just unscrews and has a 1 wire plug usally.. RC PLEASE ...
|
| 89chevy sillverado350 | 1/12/2008 |
Q: truck wont start, is getting spark, and fuel.Once in a great wile it will start, then it will run ...
A: It is flooding out. the fuel injector may me getting stuck.. thats the first thing id check.. you ...
|
| Nissan Maxima | 1/11/2008 |
Q: I am writing to ask your opinion in a recent spur of car trouble I have had. I drove my car ( 1999 ...
A: I would change the motor oil and trans fluid...pull your spark plugs..Charge the battery...then see ...
|
| Small Block chevy Rebuild | 1/9/2008 |
Q: I am rebuilding a 79 chevy 350 motor. i am having the machine shop bore the cylinders .030, and ...
A: 305 heads will increase the compression with flat tops ratio to 10.5:1 you will need to run premium ...
|
| oil pressure sending unit and oil pump | 1/6/2008 |
Q: I have a 94 Chevy G20 350 V8 automatic. My oil cooler hoses were dripping a little. I replaced the ...
A: that is common for an engine that has worn bearings and excessive clearances..I belive the problem ...
|
| Pulling harmonic balancer off 1996 Honda Accord | 1/5/2008 |
Q: I have tried every conceivable means of removing the bolt on holding the harmonic balancer in place ...
A: I have had the same problem in the past.. they are guled with loctite.. try heating the bolt with a ...
|
| 2001 Monte Carlo SS | 12/22/2007 |
Q: I have a 2001 Monte Carlo SS that won't start. When I turn the key, all the electronics come on, ...
A: First check to see if the bayyery is fully charged..if so check cable connections. if they are all ...
|
| Repair Cost Question | 12/21/2007 |
Q: We are considering purchasing a 2000 Hyundai Elantra. It needs alignment and right front boot. It ...
A: Unless you are buying REALLY CHEAP..I wouldnt buy it. Those are despoable cars..They are nothing but ...
|
| CHEVY IMPALA | 12/18/2007 |
Q: Hey there I want to ask you for advice to buy a car. Im thinking of buying a car fom this guy from ...
A: that might be top dolloe for that car.. oil could be leaking from anywhere... have a mecanic look to ...
|
| brake problem/1994 Buick Lesabre | 12/18/2007 |
Q: does brake light come on when rotors are going bad? front brakes are squealing/vibration when ...
A: no..the brake light will only usally go on if there is hydrolic leak..or uneven pressure between ...
|
| dodge dakota gas mileage | 12/18/2007 |
Q: I have a 2001 Dakota and my gas mileage just gets worse and worse. I run fuel injector cleaner in ...
A: Try replacing the oxygen sensor and air up your tires.. Thats about all the mantanance you can do.. ...
|
| Motor Oil types | 12/14/2007 |
Q: Would you happen to know of any resources that a Quick Lube type place would use to identify the ...
A: I usally use 10w/30 in engines with less than 20,000 miles..but as the miles wear..use thicker ...
|
| 1985 s10 starter | 12/12/2007 |
Q: My son has a 1985 s10. he replaced the starter, but when he turned the key, there was nothing. The ...
A: yes..double check your wires to the selinoid. use a test light..turn the key to start pos. the wire ...
|
| automotive | 12/6/2007 |
Q: I will be on vacation and away from my car for a little over a month. It is parked in a garage and ...
A: I would make sure your anti freeze coolant is strong enough to last the winter..is it VERY green?? ...
|
| No Heat on 94 Ford E 150 5.8 L | 12/6/2007 |
Q: Thermostat is working. Water Temp. will not come up. If we put something between fan and radiator ...
A: either your fan clutch is kicking in too soon.. or you need to restrict the flow of air during cold ...
|
| 85 Chevy k20 4x4 350 | 12/4/2007 |
Q: I recentley put a gasket kit on the motor also new cap rotor wires and plugs. I put the motor on tdc ...
A: Check to see if your choke is stuck on..Or open all the way.. It may not be adjusted ...
|
| 98 Mustang GT | 11/26/2007 |
Q: The check engine light has come on, the engine will start but will not idle. Without me giving it ...
A: Just a guess...... Check for a vacuum leak.. I have fixed a simular problem on a mustang this past ...
|
| 94 ford ranger 4 liter 4x4 | 11/25/2007 |
Q: I'm having some issues with my brakes. I was losing braking so I checked my back brakes and found ...
A: Sounds to me that your master cyl is leaking internally. Chenge it out..Bleed all 4 wheels. It will ...
|
| 1995Chevy Beretta 3.1L | 11/23/2007 |
Q: Hey there, I have a 1995 Chevy Beretta 3.1L with about 188,000K. The Intake manifold is going and I ...
A: You should repair it as soon as possible. coolant in your oil will ruin your crankshaft bearings.. ...
|
| Freeze Plug/Block Heater | 11/19/2007 |
Q: I'm trying to install a block heater in a 2000 Silverado 5.3L V8 but having trouble getting the ...
A: Sounds to me you will have to unscew that one most other freeze plugs are flat stamped steel.. Those ...
|
| Buick 96 lesabre rear brakes | 11/18/2007 |
Q: the star wheel on my drum brakes did not adjust and ended up falling off and bouncing around while I ...
A: Its hard for me to visualize.. But i first install the shoe connected to the parking brake cable ...
|
| 94 caprice classic | 11/14/2007 |
Q: My Problem Is My Caprice Just Started Popping And Backfiring Like I Was Running Out Of Gas.I Put In ...
A: Could be either..Your carb is flooding /Choke is on.. Or your valve timing is off../timing chain or ...
|
| 1989chevy blazer distributer | 11/7/2007 |
Q: how to install distributer in 89 Bazer with 4.3 litre motor and set the timing and placing number ...
A: You can pull the #1 spark plug.See where the piston is at its highest..crank by hand to see......I ...
|
| ford contour 1999 that has died | 10/31/2007 |
Q: So basically, the car was running for about 10 min. before I drove it down the street where it ...
A: Check your fuel pump and ignition module.. the oil in your spark plug hole is meerly the valve cove ...
|
| 96 pontiac bonneville front brakes | 10/28/2007 |
Q: Such as removing the master cylinder cover when compressing the piston to install the new pads?
A: Should be no different than any other car.. I usally bleed the caliper while i compress the piston. ...
|
| 1967 Cadillac Horn | 10/26/2007 |
Q: I bought a '67 Caddy convertible 18 months ago; and that beautiful sounding horn hasn't worked since ...
A: If you know the location of each horn..You can test the wires with a test light.. Have someone push ...
|
| clutch 1989 mitsubishi pajero 4x4 | 10/25/2007 |
Q: I was driving from work to home this morning and my truck went into 1st gear easily and when I went ...
A: Either you cluch cable is broken..OR..If its a hydrolic system..Your Master or Slave cyl could be ...
|
| v 10 Ford stuck valve | 10/25/2007 |
Q: I resantly installed a 1999 Ford V10 engine from a motor home chassie which has been setting for ...
A: Try Marvel oil in yout motor oil and in your fuel.. That might help.. I woul also pull the valve ...
|
| 95 astro rear axel seal | 10/23/2007 |
Q: Can I or should I try to repair this, is it a unit orshould i change both seals or axels at one ...
A: Yes i would change both and check for axle and bearing wear while your there..Clean or repace the ...
|
| starter | 10/22/2007 |
Q: were is the starter located on a 94 chevy blazer 6 cylinder
A: The starter should be located on the passenger side near the raer of the engine. Good luck.. RC ...
|
| 1999 Ford Mustang | 10/17/2007 |
Q: When I turn my steering wheel to the left I hear a grinding noise. Could this be the cv joint or ...
A: It could be a wheel bearing or Brake pads worn out.. Im pretty sure your mustang is rear wheel ...
|
| catalytic converter | 10/13/2007 |
Q: I have a 1999 Acura Cl 3.0 and I want to replace the cat. To remove it is there anything tricky that ...
A: If you can unbolt it GREAT! Spray WD-40 on the bolts to loosten the rust first. But most are cats ...
|
| brakes | 10/12/2007 |
Q: I've recently replaced front brakes on my '98 Ford Mustang. They were grinding and found to have ...
A: You may need to look at them again...You may have something rubbing the rotor or mybe your rear ...
|
| 72 chev pickup w/350v8 | 10/7/2007 |
Q: what is the points gap
A: That would be about .018" -/+.002 Your dwell reading should be 28-32 at idle and would set the ...
|
| Odd overheating problem | 10/7/2007 |
Q: I've got a '79 Chevy C-10 pickup with a 305 under the hood, and I've had the oddest overheating ...
A: Sounds like the thermostat is not opening.. Either you are installing the thermostat up side ...
|
| Maby you can help me? | 10/1/2007 |
Q: Mr. Ron, I have a 1991 Ford F-350 with the 7.3 Diesel, when I turn the key, the truck doesn't do ...
A: If it starts when you jump the solinoid..your ignition curcit is not working... It could be the ...
|
| strange noise | 9/29/2007 |
Q: I own a 2002 Mercury Mountaineer. I notice about 2months ago strange metal on metal bump, when I ...
A: Tha sound could be your CV axles OR you shock/strut tower mounts or upper bushing/bearings in the ...
|
| Car stalling | 9/29/2007 |
Q: A few months ago on a really hot day, I was in stop and go traffic and my car started stalling so i ...
A: you may have 2 problems going on.. The stalling whe hot might be the ignition module getting too hot ...
|
| volkswagen brakes | 9/26/2007 |
Q: Just bought a 1991 Jetta. The brakes seemed soft. We replaced the front left pad (only one with ...
A: I would take the bleeder srcews all the way out and claen them..I bet they are clogged.. ...
|
| 2002 Tahoe | 9/26/2007 |
Q: Coolant disappearing every 500 miles or so with no visable leak, and lifters are noisy after about ...
A: I think that you can rebuild an engine useing better parts than GMs new engines are built ...
|
| 1996 350 Vortec w/ low oil pressure | 9/26/2007 |
Q: The vehicle in question is a 1996 Chevy K1500 w/ a Vortec 350. At start up the pressure is normal ...
A: Your problem is simply engine bearing clearances are too big..Just from normal wear.. Not much you ...
|
| 1997 FORD AEROSTAR | 9/24/2007 |
Q: Ron, When turning the steering wheel on my Ford Aerostar it feels like it is skipping and vibrates. ...
A: I would look at the motor & trans mounts and the CV axles first..See if they are worn out... PLEASE ...
|
| Emergency brake problem | 9/23/2007 |
Q: I changed my wheel cylinder on the drivers side because it was leaking fluid and also installed a ...
A: either you parking brake cable is jammed up or too tight.. or...you need to chech your rear brake ...
|
| Engine issues with a 2002 mercury cougar. | 9/21/2007 |
Q: My fiance owns a 2002 mercury cougar. 2 months ago he had to replace the engine on it with a used ...
A: Used engines are always a scray deal there is no real proceedure for installation.. I always change ...
|
| brake problem | 9/17/2007 |
Q: I own a 99 Durango (4WD, 4 wheel ABS). Over the weekend I replaced both front wheel bearing hubs, ...
A: Jack up the wheels and double check for bearing loosness... also is you did not clean off the anto ...
|
| 1998 Chevy Tahoe Ticking | 9/17/2007 |
Q: tonight my boyfriend started my Tahoe, and there was a loud ticking noise that sounded like a ...
A: That can happen with any high mileage engine... is a combination of worn cam and crank bearings.. ...
|
| 03 pontiac grand prix | 9/16/2007 |
Q: when i hit a bump or turn the wheel (sometimes) i hear a thump or bang like something is loose on ...
A: It could be your front strut upper bushing or bearing..Or the strut itself..Struts are nothing more ...
|
| Toyota Corolla automatic trans | 9/13/2007 |
Q: I have a 91 Toyota Corolla with less than 150,000 mi on it. Recently, while driving at about 50 ...
A: Used automatic transmissions can be a scary deal... Make sure you get some kind of warrantee..most ...
|
| 2003 VW Passat that says it's overheating | 9/4/2007 |
Q: Hey! I'm hoping you can help - I have a 2003 VW Passat with 50,000 miles on it. Up until now it's ...
A: Concidering all of the symtoms you have stated.. I would check to see if your A/c System is slightly ...
|
| Ford Explorer 98 | 9/4/2007 |
Q: "The Problem at hand" I was driving a used Explorer that I had purchased a few months ago and ...
A: The 300$ motor sounds like the best bet...as long as it is in good shape.. repairing your motor ...
|
| CAR PROBLEMS | 9/4/2007 |
Q: My car (volkswagen jetta-1999 with 111,000) has been stalling. I first noticed it when I'd come to a ...
A: The fuel pump may be the problem..they are very expencive...maybe you can find a used one at a junk ...
|
| Brake Squeal | 9/4/2007 |
Q: I just had my brakes and rotors replaced by a Toyota Dealer using my supplied parts (Akebono Brakes ...
A: Ethier they are low quality brake pads..or the mechanic did not install anti squeak lube on the back ...
|
| 1994 ford explorer transmission | 9/3/2007 |
Q: i have a 1994 ford explorer (automatic 4x4); when shifting into any gear other than reverse there is ...
A: It could be low on fluid or needs a fluid and filter change.. Try that before you do any repairs... ...
|
| 93 Ford Tempo | 9/1/2007 |
Q: How hard is it to replace the cooling compressor? I also know I can buy a pulley that is put on when ...
A: It is not very difficult to replace the A/C compressor....But it is VERY difficult to install an A/C ...
|
| front brakes | 8/24/2007 |
Q: Having trouble stopping my car.Its hard to push the peddle down.just had the brakes changed then the ...
A: if your pedal feels hard as a rock but wont stop..its your power brake booster... Check the vacuum ...
|
| choosing the right oil ? | 8/22/2007 |
Q: I have 151,000 miles on my 1994 ford Taurus. I sometimes tow a 21’ boat. (once or twice a year) I ...
A: any 20/50 name brand oil would be great.. Castrol is a great choice.. Thats what Id use,,, Good ...
|
| 92 ranger | 8/22/2007 |
Q: Im not sure if you deal with ranger questions or not but here goes. I have a 92 ford ranger 5 speed ...
A: double check your battery cables and test your hot wire from your ignition key to your solenoid with ...
|
| refgearbox on renault 5 | 8/20/2007 |
Q: when the engine is warm i have trouble getting into 1 and second gear how do i adjust the clutch as ...
A: In most cases//you must take all the free play out of your clutch linkage..Or...If its a hydrolic ...
|
| timing of a isuzu pup | 8/17/2007 |
Q: i have a 1986 isuzu pup 2.3 4cyl my timing belt broke and i had the manual and replaced it, it ran ...
A: Just set your crankshft timing mark on 0 TDC #1 cyl Compression Stroke. Install the Dist with the ...
|
| 2 questions | 8/10/2007 |
Q: I actually have 2 questions: 1. What are the torque specs on the transmission pan bolts on a ...
A: If you are replacing the trans pan gasket..put RVT silicone one the pan only..set the gasket in ...
|
| Chevy Blazer Transmission dip stick | 8/10/2007 |
Q: I feel kind of silly but I can't find the dipstick to check my transmission fluid. Could you give ...
A: it should be located on the passenger side of the truck.. near the back of the engine...check when ...
|
| Manifold Leak | 8/6/2007 |
Q: I have a 1998 Dodge Caravan with a 3.3L engine. I thought that I had a bad muffler but when I took ...
A: I would buy a used exaust manifold at a truck wrecker If its craked and not repaiable..and have your ...
|
| Shaking Denali | 8/5/2007 |
Q: My 1999 Denali shakes terribly when I hit the brakes. It does not happen if I am going slow. I had ...
A: Even though your pads and shoes are still good.. You may have warped disk rotors or drums.... Sounds ...
|
| Whistling noise coming from engine | 7/31/2007 |
Q: I have an '04 Chevy Impala, 56,000 miles. Recently I have begun to hear a whistling, like a tea ...
A: Yes..I would check for vaccuum leaks first... Get a rubber garden hose lenght 2ft.. And use as a ...
|
| New Brakes | 7/31/2007 |
Q: How much should it really cost to replace the brakes on a 2003 Mercedes C230 Kompressor? I just ...
A: Just to replace pads..inc labor.....$100 per front or rear... Thats providing the pads are not super ...
|
| 98 dodge ram 5.2 missing and poping | 7/30/2007 |
Q: I have just re built the engine in my 98 dodge ran 1500 4x4 with the 5.2 liter engine. The engine ...
A: Either you cam timing is off... Or your cam/crank sensor is defective... Worn out disributor. Also ...
|
| Intake Manifold leak | 7/28/2007 |
Q: My son has a 98 350 vortec that had an intake gasket go out.When caught it there was an extremly ...
A: Yes..Sometimes the coolant in the motor oil will ruin the engine bearings if it was driven for any ...
|
| igntition coil has no spark | 7/27/2007 |
Q: i have a 1992 buick park avenue 3.8 and just recently changed ignition coil and module, because the ...
A: Check your camshaft and crankshaft position sensors..They are what control your ignition timimng and ...
|
| brake power booster removal | 7/26/2007 |
Q: How do i remove the power booster linkage from the brake pedal
A: Most cars have a spring clip you need to pull out of the brake pedal shaft..use a needle nose ...
|
| Running Hot/Oil Pressure | 7/23/2007 |
Q: Ron - I have a 1997 Bonneville SSE 3.8 V6 no supercharger. It runs hot in hot weather 88+ and has ...
A: Sounds like common bearing wear clearance problem.. Try using 20/50w oil and see if it helps your ...
|
| investing hazards | 7/23/2007 |
Q: Chris On the business end of auto repair. I am about to invest in a repair shop that seems to be ...
A: You should ask to see his books and possibly his taxes from previous years.. see if they have a list ...
|
| ford motors (Over my head) | 7/22/2007 |
Q: I need to buy my wife a car soon. Either a ford fusion(2.4) or ford focus(2.0) Are they the same ...
A: Actally those are both cars i would stay away from if they have alot of miles..Unless you get a good ...
|
| Ford Taurus front brake calipers | 7/22/2007 |
Q: My question is about a 2003 Ford Taurus. I work in a body shop doing frame, structure, mechanical, ...
A: Most ford brake caliper bolts require a star/torques bit to remove. im not sure if the year requirs ...
|
| 1993 mazda protoge | 7/17/2007 |
Q: My 1993 Mazda Protoge Blew a Heater Hose And Over Heated I Repaired The Hose Now The Car Idles Rough ...
A: You may have overheated the engine and damaged the head gasket..It may be leaking coolant into one ...
|
| manual transmission ticking | 7/17/2007 |
Q: I have a 1987 ford ranger 5 speed my transmission started making a ticking noise when in neutral or ...
A: It could be internal tranmission problems.. I would first check the fluid level on the trans.. There ...
|
| Tune up---Grand Marquis | 7/16/2007 |
Q: What parts constitute a tune up on a 1993 Mercury Grand Marquis? (5.0L/302---106,000 mi.) Is it ...
A: Yes id replace the plugs--plug wires, fuel and air filters. also the dist cap and rotor if ...
|
| 1995 Dodge Dakota 318 V8 | 7/15/2007 |
Q: Just lately when starting cold the engine stumbles,coughs,spits & backfires. When it warms up it ...
A: Sounds like a fuel mixture problem.. It can be a bad 02 sensor or other FI control.. Better go to a ...
|
| Oil Light | 7/8/2007 |
Q: 98 Dodge Strauss 6cyl when I senp on my brakes the oil light comes on Why?
A: Normally that would mean your engine is low on oil.. first check your motor oil level.. If thats up ...
|
| Brakes | 7/5/2007 |
Q: I want to replace the front pads on my 99 Lincoln Town Exec car. Manufacturers list pads by wether ...
A: I dont know why the pads would be different.. You can use a magnet to test the caliper pstons.. It ...
|
| an unknown 350 v8 | 6/28/2007 |
Q: said you specialize in chevy v8's heres a good brainteaser just wondering what if anything you may ...
A: Thats a wierd problem.. Ive never run into.. First of all..I have never heard of mix matching the ...
|
| Speed Sensor | 6/24/2007 |
Q: I have a 2002 Hyundai Accent with 60500 miles and had to have the speed sensor replaced because the ...
A: I am not a hyundai expert ..but most speed sensors are located moutnted on the transmission..it is ...
|
| Front End:Wheel Shaking, Wheel Hobble | 6/23/2007 |
Q: I have a 1993 Jeep Grand Cherokee. It has a pro-comp lift and 31" tires . When I am driving and ...
A: That is a common jeep problem...They can handel large tires very well.. Try to rebalance your tires ...
|
| ABS | 6/22/2007 |
Q: have problem with brake-ABS. The ABS start working (you can heard they working) just before the ...
A: ABS brakes can be tricky... Try bleeding all 4 wheels and see if that helps... you should buy a ...
|
| Bad Injector 96 Olds Cutlass 3.4L | 6/22/2007 |
Q: My '96 Olds with 3.4L engine started missing at idle (PO300 code-misfire) and producing a bad gas ...
A: Yes i would replace the bad injector..Leave them all hooked to the fuel rail.. clean them off with ...
|
| car wont start | 6/22/2007 |
Q: i have a 95 caprice V8 350 the car wouldn't start so i put on a starter the car crank but it wont ...
A: Yes it could be the flywheel orjust a defective new starter.. look at the flywheel teeth if you take ...
|
| Automobile Air Conditioning | 6/21/2007 |
Q: I have a 1994 Honda Del Sol. The air-conditioner is not cooling properly. The air-conditioner works ...
A: Either you are low on freon charge or your condesor fan in front of the car is not working.. A ...
|
| 1997 Venture Power Seat Won't Work | 6/21/2007 |
Q: I have a Chevy Venture and the driver's side power seat quit working. I checked the power to the ...
A: Im not much with electric problems..But... Im sure you can test the motor somehow by putting power ...
|
| Low oil pressure (guage) | 6/20/2007 |
Q: Could you please tell me what it means when my oil pressure gauge "reads" low....close to the zero. ...
A: A few things can cause that.. High milage/Worn engine bearings...(usally a knocking sound) Low oil ...
|
| 1991 Toyota 4x4 PU | 6/20/2007 |
Q: I have an automatic trans in my v6 pickup. The truck runs great with no vibrations or clunking. The ...
A: I am no transmission expert..But it sounds like it could be a speed sensor problem or something else ...
|
| '03 mazda mpv | 6/14/2007 |
Q: Our minivan is unable to idle without depressing the accelerator pedal. When starting, I have to ...
A: Yes it could be the TPS but before you replace it..check your air filter and clean out the throttle ...
|
| Mitsubishi Expo transmission | 6/11/2007 |
Q: I am searching for a manual transmission for a 1993 Mitsubishi Expo. I was wondering if any other ...
A: I ran into a simular situation on my Mighty Max 87 It would only fit 1 certain transmission.. It ...
|
| rear brakes on a vectra 2.5 v6 | 6/10/2007 |
Q: i have no idea but ive decided to try and take the job on myself , we have not long brought the car ...
A: .Most cars with rear disk brakes will require actual screwing in the caliper pistons while ...
|
| 1994 Nissan Altima GXE manual | 6/7/2007 |
Q: Car has been well-maintained, and has 148,000 miles on it. Last week I turned it on and it was ...
A: Yep..Sound like it was a stuck valve if there was no compression before...A bad fuel injector will ...
|
| CLICKING VALVES??? | 6/7/2007 |
Q: I HAVE A 2003 NISSAN XTERRA. EVERY TIME I CHANGE GEARS I HEAR CLICKING VALVES UNTIL I GET INTO 4TH ...
A: Im not sure if that model has adjustable valves or not ...some are not adjustable....If so..I would ...
|
| fuel line | 6/6/2007 |
Q: 2001 hyundai elantra; a 2 inch section of fuel line underneath my car is badly rusted, how do i cut ...
A: It is probably not a good idea to put a rubber hose repair on it if you can repair it. You will need ...
|
| transmission | 6/3/2007 |
Q: i have a 88 mercury cougar with a 302. my problem is the transmission shifts a little to hard for ...
A: Most fords do have a band ajustment on the transmission.. I not really sure on that model.. But ...
|
| Honda accord 1989 carburator stalling wen braking/no brakes | 6/1/2007 |
Q: my car(honda accord 1989 carburator) was stalling/lacking power for awhile wen i was braking at ...
A: Sound to me like your pwoer brake unit has a vacuum leak.. I reccomend replacing the master Cyl and ...
|
| 1999 camaro cylinder order | 5/31/2007 |
Q: Where is the number 5 cylinder located at on a 1999 chevrolet camaro 3.8 v6?
A: It should be the cylinder on the back of the left side of the engine..(Drivers side)Cyls 1-3-5 on ...
|
| GAS then dies | 5/30/2007 |
Q: I have a 1990 Grand Prix SE, 3.1 multi port engine V6...For quite awhile my vehicle has been acting ...
A: WOW...sounds like a big headache...First i would try testing your fuel pressure...you will need a ...
|
| head gaskets??!! | 5/30/2007 |
Q: I have a 1992 chevy tahoe. last night i shut the car off for awhile and later when i went to ...
A: It may be the ignition module or...........there is a torque converter switch on some GM ...
|
| 1997 Ford Taurus | 5/30/2007 |
Q: My passenger side window intermittently has stopped working for about a year. Now it's DOA. I took ...
A: I am not much help when it comes to electrical problems..You pretty much already tried everything i ...
|
| 1970 Dodge 318 V8 D200 Truck Tune-up specs. | 5/28/2007 |
Q: Can you tell me which is 'cylinder #1? What should the dwell reading be? What are the default ...
A: I would set the point gap at .018" If i remember correctly... The dwell should be around 28-32... ...
|
| 1970 Dodge 318 V8 D200 Truck Tune-up specs. | 5/28/2007 |
Q: Can you tell me which is 'cylinder #1? What should the dwell reading be? What are the default ...
A: Your #1 cylinder should be the most froward one one the drivers side...usally you can see the ...
|
| 2004 Sienna | 5/28/2007 |
Q: I have had to replace both front end wheel bearings and it looks like I am going to have to replace ...
A: Most wheel bearings should last 60-100k or more miles... Are you also replacing the hub?? I always ...
|
| Heater controls | 5/24/2007 |
Q: I took my rad out of my 1994 Chev p/u 350 eng,and had it repaired when I put it back in everything ...
A: Thats a wierd one...\ I would double check to see that your coolant is full. You should always top ...
|
| fuel pump? | 5/23/2007 |
Q: I have a 1992 chevy tahoe. last night i shut the car off for awhile and later when i went to ...
A: Yes..it could be the fuel pump.. If it wont start...Give it a shot of starting fluid... if it starts ...
|
| 03 trailblazer waterpump | 5/22/2007 |
Q: The fan on my v6 wobbles and makes alot of noise while the vehicle is running. Myis the water pump ...
A: While the engine is off.....Grab the fan blade and try to wiggle it you will see if the fan clutch ...
|
| 1995 chevy s-10 transmission | 5/17/2007 |
Q: one day i was driving and my transmission just went out there was no power being transferred at all. ...
A: Im not much af a trasmisson expert..but it sounds like more than a torque converter problem.. I ...
|
| chevy corsica 3.1 losing injector pulse | 5/13/2007 |
Q: Sometimes I have a no start condition and other times it will start and run for a while and ...
A: Im afraid you have already tried everything i can think of....Sounds like a weird problem.... I do ...
|
| 97 Chevy Silverado | 5/12/2007 |
Q: I am trying to replace the water pump and can't get the fan off to get to the pump. It is front ...
A: Ahh..Those are tough ones.. I usally leave the belt on to help hold the pully still..If you have ...
|
| Honda Accord 1996 Water problem | 5/10/2007 |
Q: My Honda Accord 1996 has treated me fine until now, after a sustained period of medium to light rain ...
A: Well my freind, Im sure it is a leaky rubber strip located either on the trunk lid seal. Or the top ...
|
| My 93 eagle talon 1.8L Automatic | 5/10/2007 |
Q: I am inquiring about how to properly change the timing belt. I am not sure about the timing marks. ...
A: Im not 100% sure on your talon.. But....Usally most veichles will have a dot on the timing ...
|
| 97 cavalier | 5/9/2007 |
Q: i was wondering where is the location of the PCV Valve on a 97 Cavalier.
A: Good question.....I havnt got a clue.. If its not connected to the valve cover..Look under the ...
|
| Eagle Talon oil pressure | 5/7/2007 |
Q: The bolt from the oil pump pulley came out on my 92 Eagle Talon tsi turbo and allowed the pulley to ...
A: If you have run the vehicle without the oil pump pumping for any length of time.... You may have ...
|
| preventive maintenance | 5/4/2007 |
Q: Though this may be a naive and generic question please bear with me: I recently had some work done ...
A: Ill try to make this short and sweet...Here are some basics.. Change motor oil & filter every 3-4000 ...
|
| brakes | 5/3/2007 |
Q: I recently replaced my brake pads (front and back). When I took my first ride afetr replacing them, ...
A: Is it disc brakes front and rear?? If so ...did you screw in the rear caliper pistons?? You may ...
|
| 97 Subaru | 5/3/2007 |
Q: Its only happened about 5 times in the past month and a half but its scary and kind of dangerous- ...
A: THATS A TOUGH ONE.. I am no subaru expert but ..heres what i would do. I would first check the ...
|
| Tow a 2001 neon | 5/2/2007 |
Q: I want to tow a 2001 Dodge Neon on the back of my motorhome. I will be installing a Remco pump for ...
A: I truthfully do not know the answer to that one..Maybe you can install a battery disconnect switch?? ...
|
| 2003 Chevy Trail Blazer | 5/1/2007 |
Q: how do you remove the fan shroud in order to replace the water pump
A: it is not always required to remove the shroud.. but it will give you more room to work.. it ...
|
