| Subject | Date Asked |
|
| 57 T-Bird | 11/21/2009 |
Q: Brad - I have a '57 T-Bird, 312 CI with Holley 4B Carb. The car idles fine in Neutral at 500-600 ...
A: Ok time to attack the engine with some serious testing. The place to start is with a compression ...
|
| 1948 fargo truck | 11/21/2009 |
Q: Ingnition coil has a single primary terminal. Can a two terminal ignition coil be used ? ANSWER: Is ...
A: This was an attempt at a theft proof ignition system. The coil mounts to a bracket and a shielded ...
|
| no tail lights or dash lights | 11/19/2009 |
Q: working on a 50 chevy fleetline I don't have any tail lights or dash lights also has factory ...
A: The fuses are in metal cylinders that are in line with the wiring and they are all over the ...
|
| 1951 chevy pu | 11/19/2009 |
Q: I have a 1951 chevy stock pu. Amp meter is discharging. when I increase the rpm's the meter moves up ...
A: Time to get a voltmeter across the battery. With the engine running at about 1500 RPM the voltmeter ...
|
| engine oil | 11/18/2009 |
Q: I recently purchased a 1949 ford f-1, the engine has 4000 mi. since rebuild. What do you think as ...
A: If it was mine I would be using a 10W-30 and watch the oil pressure. If it runs mid gauge at road ...
|
| 64 Chevy Nova | 11/15/2009 |
Q: Good Evening, I have a 1964 Chevy Nova. My problem is that gas isn't getting from the tank to the ...
A: I would rig up an external gas tank, just a 5 gallon gas can with a rubber fuel line rigged from the ...
|
| 65 transistor distributor | 11/15/2009 |
Q: I recently purchased a 65 impala. In the basement was a box of parts for the car including a delco ...
A: This answer is based on the fact that I was an auto tech in that era plus research in my reference ...
|
| powerglide | 11/14/2009 |
Q: I have not worked with auto trans before. I'm putting one in a 1972 chev 1/2 ton . What dose the ...
A: The vacuum line is connected to the intake manifold of the engine to read engine load via vacuum. ...
|
| '63 Impala 409 | 11/13/2009 |
Q: This regards my 425/409 4sp Impala. when I pull out fairly heavy "banging" sounds, coming from left ...
A: Ok, lets move to the left front suspension frame area. Upper control arm bushings and mounting ...
|
| '63 Impala 409 | 11/13/2009 |
Q: This regards my 425/409 4sp Impala. when I pull out fairly heavy "banging" sounds, coming from left ...
A: I think that the 409 would get the feeling that you do not love it unless you tickled the throttle ...
|
| 1946 column shift | 11/13/2009 |
Q: I have a 1946 chevy 3 speed synchromesh tranny with column shift. I would like to actually convert ...
A: This transmission originally had a vacuum assist on the shifter and the transmission is not really ...
|
| 79 Corvette brake pedal | 11/13/2009 |
Q: My brake pedal is very soft when engine is on, the pedal is normal when engine is off, all brake ...
A: Check the calipers and make sure that you have not put the left side on the right side and visa ...
|
| 1939 Ford starter removal | 11/11/2009 |
Q: I have a 1939 Ford Conv. Coupe. I need to remove the starter. There are no nuts or bolts visible ...
A: The starter on this engine is held in by the through bolts that also hold the starter together. ...
|
| 1965 Ford Thunderbird wont start all of a sudden | 11/10/2009 |
Q: Hey Brad, So my 65 T-bird has always started right up, one push on the gas pedal and a turn of ...
A: The problem with pushing the fuel through the mechanical fuel pump is that should the diaphragm in ...
|
| Choke pull off | 11/10/2009 |
Q: I have a 1964 Dodge Dart, 3.7l, 225 slant 6. I was going to replace my carter 1 barrel carb because ...
A: You need a choke pull off with the automatic choke. I would not advise changing to a manual choke. ...
|
| 1940 Buick radius bar | 11/10/2009 |
Q: I purchased a 1940 Buick and found out the rear radius bar has been cut off.There are no mounts to ...
A: The bar needs to have a pivot on each end that will allow the rear end to travel up and down while ...
|
| 1965 Ford Thunderbird wont start all of a sudden | 11/10/2009 |
Q: Hey Brad, So my 65 T-bird has always started right up, one push on the gas pedal and a turn of ...
A: The pump must be connected to the ignition switch to be off when the key is off. Next the pump needs ...
|
| 1955 rebuilt 235 engine low compression. | 11/10/2009 |
Q: Bought a rebuild 1955 235 full oiler to put in my 51 Chevy. I could not get it to idle so I checked ...
A: Low compression on all cylinders would lead me to a timing problem between the cam and the crank. In ...
|
| 1974 Ford E-100 | 11/10/2009 |
Q: I recently bought a 74 ford e-100. I got it home and running condition, hopped in and took a drive. ...
A: The welding and fabrication price sounds about right. You might be able to find a partial frame ...
|
| brake pressure | 11/9/2009 |
Q: hey brad, i own a 66 gt fstback.i havent started or driven in aprox 2mth. i started it this weekend ...
A: The brake problem sounds like a failed master cylinder. As to a book, check out E Bay and search for ...
|
| Carburetor/RPM setting | 11/9/2009 |
Q: 1966 Ford Mustang 6cyl, 200, 1bl. How do I adjust the carburetor fuel/air mixer and what tool is ...
A: Most auto parts stores sell tachometers that when connected to the ignition coil will measure RPM. ...
|
| Fuel mileage-Quadrajet | 11/9/2009 |
Q: I have a 84 Chevy C-20 PU with 1978 350 eng, with quadrajet carb. Seems to run good but cant get ...
A: 10 miles per gallon for a C 20 is not bad mileage. Before assaulting the carburetor check the rear ...
|
| Valve Adjustment On Ford 223CID | 11/6/2009 |
Q: How do you properly adjust the valves on a 1963 Ford F100 with the 223CID engine??
A: This is a unique semi automatic valve adjustment system on this engine. Warm the engine up and shut ...
|
| 1965 Ford Thunderbird wont start all of a sudden | 11/6/2009 |
Q: Hey Brad, So my 65 T-bird has always started right up, one push on the gas pedal and a turn of ...
A: For an engine to run it needs three things, spark, fuel, and compression. To check the spark, remove ...
|
| engine bolt specs. | 11/4/2009 |
Q: I have a 1954, 261 Chevy six motor I had re-build a few years back & it is time to install in my ...
A: The best that I can do is to send you to the following web site. the flywheel to cranck bolts are ...
|
| oil pressure loss | 11/3/2009 |
Q: I have a 1954 chevy 210 with a 235cu.in. motor that was just rebuit I have just 700 miles on ...
A: If the engine clearances were set up right on the money 30W motor oil is way to thick to get though ...
|
| 63 Ford Falcon Futura convertible V6 170 | 11/1/2009 |
Q: Bob: I recently had a 63 ford falcon futura completely restored for my daughter. The engine was ...
A: First I have a question about the battery. You say that it is new. Was it new and sat around waiting ...
|
| 1947 Packard head | 11/1/2009 |
Q: First, Thanks for your help. I have a '47 Packard 245 6 cylinder apart for overhaul. How much can ...
A: We used to figure that .030" was about the limit back in the day. However if you are concerned that ...
|
| massey ferguson generator | 10/31/2009 |
Q: I am trying to figure out if my generator is working. I'm not quite sure how. And I'm trying to ...
A: As far as using a solid state regulator to provide a more constant ;eve; of charge rather than a ...
|
| 1950 plymouth | 10/27/2009 |
Q: Is the vin# stamped on the frame? If so were!were can i fined information about a special deluxe p20 ...
A: The number on the drivers door frame is the VIN for your 1950 Plymouth. The number stamped on the ...
|
| 66 Mustang starting | 10/26/2009 |
Q: Is there a replacement gasket for a trunk mounted fuel tank for a 1967 Ford Mustang Coupe 6cy, 200? ...
A: For an engine to run it needs three things, spark, fuel, and compression. To check the spark, remove ...
|
| '86 Blazer electrical problem | 10/23/2009 |
Q: Several days ago I drove my '86 Chevy Blazer to and from school without a problem. However, an hour ...
A: The clue here is the headlights. The headlights are on a circuit from the ignition switch so it ...
|
| 57 Olds 98 gas line routing | 10/22/2009 |
Q: I'm putting a 57 Olds 98 back together for a friend and he would like the gas line pretty much the ...
A: If I were doing the job I would look in Hemmings and find one of the vendors that supplies pre ...
|
| 1948 Pontiac 6 cyl no spark at distributor | 10/20/2009 |
Q: I am trying to start a 1948 Pontiac that has been sitting outside for years. I've replaced the ...
A: Since you have made the move to the 8 volt battery you will need to take one of two paths, either ...
|
| 1972 ford f100 | 10/17/2009 |
Q: brake lights, fuel gauge and speedometer are not working in 72 ford f100. we have replaced all of ...
A: This sounds like a series of problems not just one effecting all of the items mentioned. The ...
|
| 1951 fuel/vacuum pump question | 10/17/2009 |
Q: So I bought a new fuel pump with an auxiliary vacuum pump for my 1951 chevy fleetline. I'm needing ...
A: Ok, here is what to do. Start the engine up with all of the vacuuum lines on the fuel pump ...
|
| 56 chevy | 10/16/2009 |
Q: i'm interested in a 56 chevy bel air,4sale by owner.i'm not as savvy yet about cars so what are some ...
A: Your insurance premiums will depend a lot on the state that you live in so I cannot answer that one. ...
|
| 52 plymouth starting issue | 10/16/2009 |
Q: i bought a 52 Plymouth 4 door a few years ago, and it starts up fine, but after it warms up for say ...
A: It could be a variety of things. The carburetor but be dribbling over internally flooding the engine ...
|
| vacum lines | 10/14/2009 |
Q: 1956 ford car. The vacuum lines coming from fuel pump which goes to the carb. and which goes to ...
A: The easiest way to tell is to start the engine with the lines off. Hold your finger over one and it ...
|
| Gas questions | 10/12/2009 |
Q: 2 questions, I have a 51 fleetline special. What will happen if I run unleaded through the car? also ...
A: Rust is the enemy. There is a filter in the tank that could be plugged as well. The system will ...
|
| carb or intake vacuum | 10/10/2009 |
Q: I am wondering what is better, carb vacuum(edelbrock carb) or intake for power brakes.
A: It depends on the carburetor that you have. Some have a large vacuum port, about 1/2 inch, at the ...
|
| 1948 DeSoto DeLuxe | 10/9/2009 |
Q: I am in need of the firing order for the 6 cylinder DeSoto and if you could tell me which cylinder ...
A: ANSWER: Ok, here we go. Pull number one spark plug out. Bump the engine over in short taps while you ...
|
| 1951 chevy styleline deluxe | 10/8/2009 |
Q: what differential will fit my 1951 chevy car? i remove the 216 inline six and the rest of the ...
A: None of that will fit directly without adaptors, welding and fabrication. Changing engines and drive ...
|
| 58 Ford Retractable electrical issue | 10/7/2009 |
Q: I've got an electrical question about our 58 Skyliner. most of the time we keep the top retracted in ...
A: These motors are reversible and two sets of windings in them. It sounds like the windings in that ...
|
| 6 volt to 12 volt | 10/6/2009 |
Q: I am restoring a 1952 chevy and I'm considering adding air conditioning. Been told I must upgrade ...
A: Changing from 6 to 12 does not necessitate changing any wire sizes in the system. Wire size is ...
|
| 58 Ford Retractable electrical issue | 10/6/2009 |
Q: I've got an electrical question about our 58 Skyliner. most of the time we keep the top retracted in ...
A: OK, lets look at what is happening. if you are running the engine with it at idle, the generator is ...
|
| chevy truck | 10/5/2009 |
Q: have a 1966 chevy long bed truck need to fine out if it has a 283 350 or 327 eng best way to find ...
A: There should be a series of numbers and letters stamped on a pad on the right front corner of the ...
|
| Dieseling | 10/4/2009 |
Q: A rebuilt stock carburetor was installed 6 weeks ago in my 1966 Oldsmobile Delta 88 with 425ci ...
A: Dieseling is almost always, 99%, of the time caused by the idle speed being set too high or a vacuum ...
|
| 55 chevy p/u Brake | 9/30/2009 |
Q: I have a 55 chevy p/u and my problem is the brake pedal. It gets stuck when you hit the brakes and ...
A: If it the original set up there should be a grease fitting on the pivot that if not greased can ...
|
| 1947 olds dynamic 76 4 dr sedan flat 6 | 9/30/2009 |
Q: We have a 1947 olds dynamic 76 4 dr sedan with a flathead 6. We would like to know how to identify ...
A: I think that you might be getting the cart before the horse here till you check the car out. The ...
|
| Power Steering | 9/28/2009 |
Q: how much horsepower will my 66 Corvette loose if I convert the car to power steering (an original ...
A: Ok, since my last answer was not adequate and did not list a number, I will take the time to try a ...
|
| 1962 Mercury Comet | 9/27/2009 |
Q: The generator light came on and won't go off. I tried a different generator and it didn't help. I ...
A: Ok, take one of your voltmeters and connect it across the battery. Set the scale at 20 to 40 volts ...
|
| flathead engine won't start | 9/25/2009 |
Q: good news,I finally got spark.I pulled the distributor out of the engine early on when this first ...
A: Ok, here we go. Pull number one spark plug out. Bump the engine over in short taps while you hold ...
|
| flathead engine won't start | 9/24/2009 |
Q: said I too many follow ups.I checked the ground wire inside the distributor like you requested and ...
A: At this point you should have spark. With the distributor cap in place, remove the high tension coil ...
|
| flathead engine won't start | 9/24/2009 |
Q: said I too many follow ups.I checked the ground wire inside the distributor like you requested and ...
A: Ok, now with the points closed and the voltmeter connected to the ground side of the battery and the ...
|
| engine swap/conversion | 9/24/2009 |
Q: I have a 1965 Chevy G10 Van that has a straight six engine 3.2L in it and I am wanting to put a 350 ...
A: Usually I back away from a question like this as there seams to be no one correct answer when ...
|
| 63 mercury | 9/24/2009 |
Q: i have a 63 meteor and cant seem to be able to remove the ignition. i was able to remove the tumbler ...
A: The ignition switch is spring loaded. From under the dash push towards the rear of the car on the ...
|
| flathead engine won't start | 9/24/2009 |
Q: said I too many follow ups.I checked the ground wire inside the distributor like you requested and ...
A: OK, Now get the trusty old voltmeter out. With the key on and the points open run the red lead of ...
|
| engine won't start | 9/23/2009 |
Q: I have a 8BA flathead from 1950.As I was driving along at 30mph the car started to die out and ...
A: When you installed the new points did you set the gap when the rubbing block of the point set was on ...
|
| 1947 olds, series 60 | 9/22/2009 |
Q: sorry for the lack of knowledge, how do you check the transmission fluid on this car,257 inline with ...
A: The transmission dip stick and fill tube are located under the floor mat on the passengers side of ...
|
| belt replacement | 9/21/2009 |
Q: I was driving my 1984 Monte Carlo SS yesterday when it made a clanking noise and the power steering ...
A: If the car has multiple V belts, line of sight will give you the proper grooves. That is lining up ...
|
| 1955 Cadillac Cold Start | 9/21/2009 |
Q: I have a 55 Cadillac with a 331 c.i., 4 bbl. On cold start the car idles very slow, and rough. If ...
A: It sounds very much like the automatic choke is not working correctly. With the engine cold remove ...
|
| engine won't start | 9/20/2009 |
Q: I have a 8BA flathead from 1950.As I was driving along at 30mph the car started to die out and ...
A: I wish that these barber shop "auto experts" would keep their potentially destructive advice to them ...
|
| Bronco oil pan | 9/19/2009 |
Q: I am looking at a 96 Bronco with the 302 engine that needs a new oil pan.What does it take to change ...
A: This should be a straight forward job with plenty of clearance to get the pan out once the bolts are ...
|
| 1965 Ford Galaxie 500 3 speed transmission | 9/19/2009 |
Q: my dad recently purchased a 1965 Ford Galaxie 500 with the 289 and three speed tranny on the column ...
A: I guess my question to you is simply is the overdrive unit still ion the car or did some one in the ...
|
| Battery drain | 9/17/2009 |
Q: Grandson has 67 Firebird w/ 400 engine. the battery will not hold charge. previously someone put a ...
A: The first thing to do is to have the battery load tested to be sure that it can hold a charge. Most ...
|
| 6 volt wiring | 9/16/2009 |
Q: I have 1950 dodge coronet,after setting for the winter it well not start.I have put all new ...
A: 4.3 volts at the starter when cranking is a bit low and could indicate a battery that is not up to ...
|
| 1948 buick 3 part exhaust manifold | 9/16/2009 |
Q: the roadmaster manifold is in three parts. a center section and two "horns". the two horns slip fit ...
A: When these units were made and used in the day the three units were made for a tight slip fit. There ...
|
| Gas pedal starting 1940 Buick | 9/15/2009 |
Q: Can you tell me if there's any electrical wiring to make the car start by pressing down the gas ...
A: There is supposed to be a switch on the side of the carburetor that is connected to the throttle ...
|
| Pinion nut torque specification | 9/15/2009 |
Q: I would like to know what is the torque specification of the pinion nut on the rear differential of ...
A: REPLACE PINION SEAL. The procedure that I use to replace a pinion seal while the differential is in ...
|
| 1950 Dodge 3 speed transmission. | 9/14/2009 |
Q: I have a 1950 coronet with a 3 speed. It does not go into 1st or reverse. I am not sure if it is ...
A: The way that I diagnose these problems is to jack the car up and support it on stands. Then ...
|
| rear drum removal | 9/14/2009 |
Q: i have a 1954 Chrysler Windsor De Luxe and i was wondering how i can remove the rear drum
A: REAR DRUM PULLING The rear brake drums on these cars have a tapered hole in the center and fits over ...
|
| tighting bands on powerglide transmission | 9/14/2009 |
Q: how do you tighten the bands on a 1954 powergilde transmission can you do it externally ?What is the ...
A: The only band that can be adjusted from the outside of the case is the low band and it requires a ...
|
| 1951 chrysler town & country | 9/13/2009 |
Q: a friend just inherited this beauty. asked me to help with brakes. completed front brakes ok ...
A: The rear brake drums on these cars have a tapered hole in the center and fit over a tapered shaft. ...
|
| 46 Ply Whine - Timing Chain? | 9/13/2009 |
Q: 10K miles on '46 Plymouth rebuild, stock 218, engine suddenly last week developed engine-area whine ...
A: You are testing the old gray matter that is slowly turning into mush inside my skull. But here goes. ...
|
| 1940 LaSalle Headlight Switch Replacement | 9/12/2009 |
Q: I have removed headlight knob and shaft to paint the dashboard. How do I reinstall the shaft and ...
A: On the side of the headlight switch opposite the side that the wires attach to there should be a ...
|
| 1955 packard 4 bbl rochester carb | 9/12/2009 |
Q: I've had carb rebuilt twice in a year. It runs fine for a while and the same problem comes back(it ...
A: It sounds like either the needed parts were not replaced, or dirt is being drawn up from the fuel ...
|
| borg warner overdrive 1954 | 9/9/2009 |
Q: I have a 54 dodge Od installed in a 41 Chry it was great for 3/4 yrs but on my way to a meet it ...
A: It could be that the solenoid is jammed into the ring gear. Take the solenoid off the transmission ...
|
| 1953 Chevy Clutch Problem | 9/9/2009 |
Q: I recently installed a new clutch disc, clutch cover assy, t-o bearing; resurfaced flywheel in my ...
A: If I were doing the diagnosis now I would go back to the parts that came out originally. I would ...
|
| '49 F-1 | 9/7/2009 |
Q: I recently purchased a'49 Ford F-1. It supposedly has the original 329 Flathead V-8 in it. The only ...
A: This one is as close as any that I have seen except for the color of the bumper and the side view ...
|
| '49 F-1 | 9/6/2009 |
Q: I recently purchased a'49 Ford F-1. It supposedly has the original 329 Flathead V-8 in it. The only ...
A: 98RC is the proper code for a 1949 F-1 1/2 ton pick up. 8B is the correct code for the 49 V-8 239 ...
|
| 1960 Chevy Impala horn | 9/6/2009 |
Q: I have a completely unmodified 1960 Chevy Impala that the horn stopped working in recently. Are ...
A: Ok, locate one of the horns and pull the wire from it off. Next stick the probe of the test light ...
|
| Passenger side exhaust smoke | 9/6/2009 |
Q: 1966 Ford Fairlane 500 convertible, original 390cu, 750 double pump Holley carb., edelbrock ...
A: Sounds like you might have a little oil running down a valve stem. I would not worry about it until ...
|
| 1940 La Salle | 9/4/2009 |
Q: "Hello" I have a 1940 LA Salle. Need to replace horn wire and top bearing. Would also like to ...
A: According to my reference material this rig runs a Saginaw gear box. There should be a clamp around ...
|
| 1959 Buick Invicta (convertible) | 9/3/2009 |
Q: As something of a neophyte to classic car repairs, I need to replace the four headlight bulbs ...
A: My stock answer for “where can I find….” Is to latch on to a copy of Hemmings Motor News, the old ...
|
| valve adjustment | 9/2/2009 |
Q: I need to know the specs and procedure on adjusting valves for my 64 Ford F-100 with 292 V-8
A: The valves are adjusted hot with the engine running to 0.019". it is a messy job as the oil tends to ...
|
| 1971 Ford Ranchero | 9/1/2009 |
Q: I have a 1971 Ranchero with 67,000 original miles that I want to restore and give to my daughter. ...
A: If the freeze plugs are pushed out it indicates that indeed the engine coolant has frozen. It would ...
|
| 66 mustang | 8/31/2009 |
Q: my gas gauge is broken, any advise on where to start without replacing entire system?
A: Disconnect the wire at the sender unit at the tank. let it hang free. The gage should read zero or ...
|
| voltage regulator | 8/30/2009 |
Q: we have a 61 comet. Is adjustment necessary on a voltage regulator? Someone has said this might need ...
A: Usually adjusting a voltage regulator will not be the cure for a no charge condition. The trouble ...
|
| Starting 54 Ford After Sitting... | 8/30/2009 |
Q: My '54 Ford Pickup (V-8 Four on the Floor) has been in the yard here in Minnesota for 3 years ...
A: My routine for these Rip Van Winkle cars is as follows provided that the engine will turn over and ...
|
| 1964 PONTIAC CATALINA-389 | 8/28/2009 |
Q: I have the original 389 engine w/AC inside my 1964 Pontiac Catalina. I replaced my fuel pump and ...
A: It could be but you can check it several different ways. My test is to disconnect the fuel inlet ...
|
| changing a fuel pump | 8/28/2009 |
Q: I am replacing a fuel pump on a 1950 chevy 235 need information about how to keep the rod that falls ...
A: Is this a 6 cylinder? If so there should be no push rod operating the fuel pump. The fuel pump arm ...
|
| Ticking/Whistling noise | 8/27/2009 |
Q: I have a 67 Corvair with a flat-6 110HP air cooled engine. Sometimes in very cold weather I can hear ...
A: I would not use an additive. Take a length of heater or garden hose about 3 foot long. Place one end ...
|
| Brakes | 8/26/2009 |
Q: I purchased a 1981 Chevy El Camino. The previous owner swapped in a hi-preformance 350 engine. The ...
A: If I were doing the job I would start by pulling all 4 wheels and checking the installation of all ...
|
| 1950 Dodge L6 engine | 8/25/2009 |
Q: How do you check the oil on one of these flat head motors? I have no manual yet for help. It is in ...
A: The dip stick should be down beside the distributor. As far as the oil filter goes my stock answer ...
|
| Replacement Radio | 8/24/2009 |
Q: I would like to to replace my AM radio with a new AM/FM style, but don't know if the wattage will ...
A: The output of the generator on your car could be 35 or 45 amps depending on the model and the ...
|
| identify a car (plymouth?) | 8/24/2009 |
Q: I've attached a photo of a car I'm trying to identify: believe it's a plymouth (pre-1953). ...
A: The three circles on the fender were accessory options sold as dress up accessories by auto parts ...
|
| why wont my car start after i rebuilt my carb | 8/23/2009 |
Q: I own a 1983 Monte Carlo and it sat for about 2 years, i had it running then I rebuilt my carburetor ...
A: Sounds like you might have messed up a bit on the carburetor overhaul. Time to pull it off and do it ...
|
| 1964 Rambler Classic Cross Country | 8/23/2009 |
Q: I have a 1964 Ramble Classic Cross Country 770 V8 287 V8. Do you know if I can get a wiring diagram ...
A: My stock answer for “where can I find….” Is to latch on to a copy of Hemmings Motor News, the old ...
|
| 1948 Willys Jeepster windshield wipers | 8/22/2009 |
Q: Windshield wipers are not in time with one another. Have new wiper motor, wiper on drivers side, ...
A: This condition usually indicates that the springs that hold tension on the cables is weak and ...
|
| 69 Mustang Mach 1 battery | 8/21/2009 |
Q: I am having a problem with my battery boiling after I drive it. I have completely restored my Mach 1 ...
A: That will make the battery boil. I would suspect that the voltage regulator is the culprit, or there ...
|
| 69 Mustang Mach 1 battery | 8/20/2009 |
Q: I am having a problem with my battery boiling after I drive it. I have completely restored my Mach 1 ...
A: The proper voltage regulator setting for you car is between 13.5 volts and 15.3. If the voltage is ...
|
| a/c blower | 8/19/2009 |
Q: my car had a/c befor i took it to get it painted. at the paint shop some one connected the battery ...
A: If the battery was connected backwards I would be concerned for the health of the alternator as ...
|
| 67 Mustang headlight | 8/19/2009 |
Q: I'v been restoring my 67 Mustang coupe all year long and recently had a stereo system installed with ...
A: This a sealed beam and not a removable light bulb. There is a three pronged plug on the back of the ...
|
| fuel level sending unit | 8/18/2009 |
Q: i have a 39 ford deluxe and replaced gas tank and sender.am running stock gages and sender is for ...
A: Same way as always, POS to POS and NEG to NEG. You should be able to pull the battery and turn it ...
|
| Ignition | 8/18/2009 |
Q: I have a 1966 Mustang Coupe. It's been running fine until recently when I went to start it. It has ...
A: Usually when the solenoid just clicks it is the sign of a low battery. Time to get the voltmeter out ...
|
| 1964 dodge dart | 8/17/2009 |
Q: I am tuning up a 1964 dodge dart with a 3.7L slant 6. I'm having trouble ordering the cap and ...
A: The make of the distributor and the part number is printed on the side of the distributor. You might ...
|
| 1963 buick lesabre timing chain diagnosis | 8/17/2009 |
Q: in reply to distributar. yes it is a add on unit to stock distributar. but I had the same problem ...
A: To check the timing chain for wear, remove the distributor cap. Use a wrench and turn the crankshaft ...
|
| windshield | 8/17/2009 |
Q: I have a 1954 chevy pick-up. I removed the front windshield and am trying to put a new one. For the ...
A: Place the rubber gasket in the opening in the trucks cab. Then wrap a long peice of twine around the ...
|
| 1956 t bird heater control valve | 8/16/2009 |
Q: I own a 1956 Thunderbird and are having problems with the heater control valve. The company that ...
A: There were a number of cars that used vacuum control valves for the heater water flow, it would be a ...
|
| 1963 buick lesabre timing chain diagnosis | 8/15/2009 |
Q: car runs like a crossed plug wire exhuast very rich & sputters at tail pipe. new carb,plugs,plug ...
A: I am not a fan of aftermarket pointless ignition. I have been on wild goose chases with them before. ...
|
| Starting | 8/14/2009 |
Q: Ok I have a 1974 Oldsmobile Cutlass(1975 olds engine V8 260,) I have problems starting my engine. I ...
A: Remember that with a four stroke cycle engine that the piston comes up to top dead center twice to ...
|
| Holley 885 Carburetor | 8/13/2009 |
Q: The car is a 1953 Mercury flathead with a Holley 885 carb. The engine was just tuned with new plugs ...
A: The base setting for the idle mixture needles is to lightly seat them and then back them out 1 1/2 ...
|
| 71 Ford F 100 | 8/13/2009 |
Q: I was wondering how to rotate my 302 engine without using the ignition. I am trying to get rid of a ...
A: It will be very close. The instrument cluster is different but the engine, transmission, rear end, ...
|
| 67 Buick 400 warter pump | 8/12/2009 |
Q: I'm changing the water pump on my 67 GS and would like to know if you recommend using a good gasket ...
A: Ok, take the pump off and start over. make sure that all traces of the old gasket are removed and ...
|
| voltage fluctuation at alternator and coil | 8/11/2009 |
Q: I have a 351 cleveland in a 1972 ford f100 and am having problems. When the engine is running, the ...
A: I prefer a swing needle voltmeter for cases like this. The problem with a digital is that it is a ...
|
| 1929 Whippet | 8/10/2009 |
Q: Brad, I just purchased a 1929 Willys Whippet in pretty good shape. I do need to replace the roof and ...
A: Yes, a single weight. My 41 Ford that was overhauled uses 10W-30 and runs just fine. As for the ...
|
| 1966 Mustang running issue | 8/9/2009 |
Q: I own a 1966 Mustang with a 6 cyclinder, 1 barrel carburator. The issue I am having is that the car ...
A: Rebuilding a carburetor entails removing all the adjustable screws and plugs to allow for cleaning ...
|
| Block Heater Myth | 8/9/2009 |
Q: First, I am not a mechanic. Nevertheless, I have been hearing what I consider to be a myth about ...
A: There is a nubbin of truth in their notion about the block heater, but only a nubbin. The computer ...
|
| 1984 Oldsmobile Cutlass Supreme Brougham | 8/9/2009 |
Q: I just bought an 84' Olds Cutlass Supreme Brougham. It has been sitting for about two years due to ...
A: These engines had a tendency to pop head gaskets. I would start the diagnosis process by removing ...
|
| voltage fluctuation at alternator and coil | 8/9/2009 |
Q: I have a 351 cleveland in a 1972 ford f100 and am having problems. When the engine is running, the ...
A: This sounds like there is a circuit breaker opening and closing protecting a circuit with a short. ...
|
| 1972 buick skylark custom convertiblet | 8/8/2009 |
Q: The 1972 buick skylark custom convertible has a small round hole, the sieze of a quarter on the ...
A: I do not think that this is a factory hole. It sound like the hole that we used to drill in cars ...
|
| Chevrolet wiring | 8/7/2009 |
Q: I have a 66 SS396 chevelle and the wires are missing for the neutral safety switch. where do the ...
A: Two of the terminals are for the neutral start portion of the switch and two are for the back up ...
|
| 1929 Whippet | 8/7/2009 |
Q: Brad, I just purchased a 1929 Willys Whippet in pretty good shape. I do need to replace the roof and ...
A: Unless you are going to drag race the car or use it as a farm tractor to plow the fields it will run ...
|
| Ignition Starter | 8/7/2009 |
Q: Ok I have a 1974 Oldsmobile Cutlass(1975 olds engine V8 260,) I have problems starting my engine. I ...
A: Well lets give this a try. There are two wires on the + side of the coil. The one that runs to the ...
|
| Plymouth 218 valve timing | 8/5/2009 |
Q: I am working on a 1951 Plymouth 218 flat head 6. My problem is when the timing marks on the timing ...
A: I found a note in one of my reference manuals relating to this engine and timing chain replace ment. ...
|
| towing a travel trailer | 8/3/2009 |
Q: I am in the process of fitting a tow bar to my 1949 Buick Super Sedanet, Model 56-S. The car is on ...
A: You have two problems here. The Toyota uses separate rear lights for the stop and directional while ...
|
| towing a vintage travel trailer | 8/3/2009 |
Q: I am intending to use my 1949 Buick Super Sedanet, Model 56-S to tow my 1951 Silver Streak travel ...
A: You have hit my third great passion, the first my better half, the second cars, and the third RV's. ...
|
| 1949 Buick 248 carburetion | 8/3/2009 |
Q: How do you do Brad. I have recently acquired a 1949 Buick Super Sedanet, Model 56-S. 248 ci engine ...
A: The running problem appears to be more than just a lean running condition. I would start diagnosis ...
|
| 1940 plymouth | 8/1/2009 |
Q: I have a 1940 plymouth road king. I want to keep it original, but I cant find a radiator or any ...
A: My stock answer for “where can I find….” Is to latch on to a copy of Hemmings Motor News, the old ...
|
| wiring | 8/1/2009 |
Q: Good Evening Brad another question on my 47 Ford Fire Truck with 6 volt positive ground system,I ...
A: Oh boy, this is one of those cases where you need to be there. It is a 007 case of starting at the ...
|
| Fuel issue | 7/30/2009 |
Q: I have a 57 Chevy Bel-Air. It was parked for sometime until recently. Once I got in it and decided ...
A: If I were doing this job I think that I would remove the fuel filler tube from the car first. This ...
|
| 71 Ford F 100 | 7/30/2009 |
Q: I was wondering how to rotate my 302 engine without using the ignition. I am trying to get rid of a ...
A: The starter solenoid is located on the inner fender panel near the battery. The POS cable from the ...
|
| 1949 buick dynaflow | 7/29/2009 |
Q: we have a car in our shop. the car came from nebraska, and we're trying to get the title switched ...
A: The number on the door pillar is supposed to be the legal number for the car. You could check for an ...
|
| Break light | 7/29/2009 |
Q: Hey my break warning light in my 85 El Camino wont turn off, Im not losing fluid, & i have a good ...
A: Follow the fluid lines from the master cylinder. they should enter a brass block that also has an ...
|
| Dieseling | 7/29/2009 |
Q: I have a 1966 Oldsmobile Delta 88, 425ci, with 2-barrel carburetor. I had replaced the carburetor ...
A: Vacuum leak testing is simple. With the engine running use a can of spray carburetor/choke cleaner. ...
|
| Break light | 7/28/2009 |
Q: Hey my break warning light in my 85 El Camino wont turn off, Im not losing fluid, & i have a good ...
A: The first thing that I look for is an emergency brake that is not returning all the way. Try to lift ...
|
| Dieseling | 7/28/2009 |
Q: I have a 1966 Oldsmobile Delta 88, 425ci, with 2-barrel carburetor. I had replaced the carburetor ...
A: It sounds like you have a vacuum leak perhaps between the carburetor and the intake manifold. The ...
|
| Control Arms | 7/26/2009 |
Q: i am restoring a 1968 Pontiac lemans. I torqued the control arms to frame bolts to factory specs ...
A: The rubber bushings that you are using are not supposed to move. The rubber twisting allows the arm ...
|
| 1947 Oldsmobile 68 Special | 7/25/2009 |
Q: My Olds keeps overheating, new water pump,thermostate and had the radiator repaired. I was informed ...
A: Well from one old turkey to another, here's the straight scoop, I hope. The water distribution tube ...
|
| coil resistor wire | 7/24/2009 |
Q: I replaced part of the wiring harness on a 72 Corvette. The yellow wire from the starter solenoid to ...
A: The wire from the solenoid to the coil should not be a resistor wire. That brings full voltage to ...
|
| generator change over | 7/23/2009 |
Q: 1964 Ford Fairlane with a 289 in it has a generator and i want to change it over to an alternator. ...
A: Ok, you need only run one wire from the alternator to the POS battery post or to the battery side of ...
|
| car identification | 7/23/2009 |
Q: I have recently inherited a car from my great aunt that has been identified as a 1929 Plymouth. The ...
A: To identify the car via the numbers check the following sire: ...
|
| 56 chevy sputtering when hot | 7/23/2009 |
Q: Hey Brad, appreciate your help. I have a '56 chevy pickup with a 235 straight six. Old Muddy has ...
A: The fuel line has at least one section that is higher than the level of the fuel in the tank. If the ...
|
| carborators | 7/22/2009 |
Q: I have a 62 4dr falcon with a 170, I am running and slowly restoring. I see in the shop manual that ...
A: Back in the day when i was an instructor for Ford Motor Company (50's and 60's) in New England did ...
|
| oil leak | 7/22/2009 |
Q: I purchased a 1952 chevy half ton with the original motor and transmission, my problem is it has a ...
A: Make sure that the oil is not leaking higher up on the engine like the valve cover or the side plate ...
|
| 1952 chevy delux water pump | 7/21/2009 |
Q: can you walk me thru replacing a water pump on a 1952 chevy delux 216 straight 6
A: The first thing to do is to drain the cooling system by the petcock on the bottom of the radiator. ...
|
| 41 Ford Flat head ignition problem | 7/20/2009 |
Q: I am getting power to the coil with continuity through the coil and to the capacitor. The capacitor ...
A: The capacitor only has continuity for a nano second when current is applied to it as it stored ...
|
| !967 Chevy Impala | 7/20/2009 |
Q: This is probably and easy one for ya but for someone who knows very little on cars it's a bit tough. ...
A: If the starter is clicking it usually indicates a weak battery or a bad connection in the battery ...
|
| 69 Ford Fairlane - no wipers & no turn indicator | 7/20/2009 |
Q: Recently bought the above vehicle and the turn signals quit working the same time the wipers stopped ...
A: The wipers and the turn signals get their power from the ignition switch to the fuse block. Then to ...
|
| 62 falcon | 7/20/2009 |
Q: i bought a 62 falcon 6cyl 3sp on the column as a daily driver a few months ago, replacing the usual ...
A: Nice looking car. The transmission problem is probably internal, but not missing teeth. However ...
|
| Front Beak Line for rear Drum Break - 1968 Plymouth Fury 3 | 7/19/2009 |
Q: I'm completely novice at car restoration but have help to do so. I have run into the following ...
A: Sad to say that your local parts store is not the place to go for advice on old cars. There are ...
|
| adjust brakes | 7/19/2009 |
Q: How do I adjust the brakes on my 1953 Chevy Bel Air. The brake pads good.
A: There should be two slots at the top of the backing plate on either side of the wheel cylinder ...
|
| filling brake fluid on 1956 Pontiac Chieftain | 7/19/2009 |
Q: The reservoir for the brake fluid on my 56 Chieftain seems largely inaccesable, tucked under the ...
A: Back in the day when I was young working in the family garage we had a small pump that fit into the ...
|
| charging system | 7/17/2009 |
Q: I own a 1947 Ford Fire truck powered by a 100 HP flat head V8 with a 6 volt positive ground system. ...
A: There should be continuity between both ends of the "A" wire. There should be no splices in or to ...
|
| fuel pump | 7/15/2009 |
Q: I own an 82 vette,fuel pump runs but does not pump fuel.What is the problem?
A: The in tank fuel pumps have been known to separate from the fuel delivery tube in the tank. The ...
|
| Carb flooding/stalling after warmed up | 7/15/2009 |
Q: Brad, I have a 75 vette with a 5 yrs old GM crate motor. The stock Quadra Jet was replaced about 3 ...
A: 8 to 10 PSI can be too much of a good thing and be holding the needle valve open a bit. Especially ...
|
| Triple Reserve Gas, oil & water tanks | 7/14/2009 |
Q: I came across these and was wondering if you might know what they are and if they were ever used on ...
A: You have a great find. What you were told is correct except the charactization of used on model T. ...
|
| Carb flooding/stalling after warmed up | 7/14/2009 |
Q: Brad, I have a 75 vette with a 5 yrs old GM crate motor. The stock Quadra Jet was replaced about 3 ...
A: Based on what you tell me I think that the original problem that appeared to be solved with a vented ...
|
| 1963 Chevy | 7/14/2009 |
Q: Again, I would very appreciate you sending me the correct info that will permit me to see your ...
A: I can help you fix your car but as far as figuring out how to work the web site goes, faggetaboutit! ...
|
| 1963 Chevy Impala | 7/13/2009 |
Q: I recently submitted a question about my steering wheel not coming back to center after a right or ...
A: I can help you fix your car but as far as figuring out how to work the web site goes, faggetaboutit! ...
|
| charging system | 7/13/2009 |
Q: I own a 1947 Ford Fire truck powered by a 100 HP flat head V8 with a 6 volt positive ground system. ...
A: To polarize the generator remove the field "F" wire from the regulator and touch it briefly to the ...
|
| 63 Chevy Impala | 7/12/2009 |
Q: I have restored a 63 Chevy Impala, 283 motor, automatic, no a/c. New front end suspension ...
A: If the problem is only when the car is moving I would lean more to the caster and toe in settings ...
|
| Flasher Switch | 7/12/2009 |
Q: How do I replace the (indicator) flasher switch on a 1962 T-Bird? It seems to only work ...
A: The flasher itself would be the first thing that I would consider as the problem not the switch up ...
|
| 1967 Impala 283 firing order | 7/11/2009 |
Q: I have a 1967 Impala, and was wondering if you could tell me the correct firing order?
A: The firing order is 1-8-4-3-6-5-7-2. Number one is the first cylinder nearest the radiator on the ...
|
| generator light | 7/10/2009 |
Q: I have a 78 olds delta 88 4 door, 350r engine. Last week my generator light came on. its kind of dim ...
A: The easy test for this condition is to first check the GAGES/TRANS fuse in the fuse block. If it is ...
|
| 1971 dodge 318 not getting any spark | 7/8/2009 |
Q: i have a 318 thats not getting any spark.i just replaced the timing gears and chain because it ...
A: A couple of tricks. First remove the distributor cap and have someone turn the engine over while you ...
|
| Brake lights | 7/7/2009 |
Q: The driver side brake lights on my 1964 chevy are not working, The turn signals on that side do work ...
A: If the directionals work but the stop light does not the most probable cause is a defective turn ...
|
| Just starting, Please help | 7/7/2009 |
Q: I want to get into restoring classic cars, but I don't know where to start. Where do I begin? ...
A: My stock answer for where can I find….” Is to latch on to a copy of Hemmings Motor News, the old car ...
|
| generator light wont go off | 7/6/2009 |
Q: I have a 1962 ford thunderbird . I have a new battery that I purchased last year it holds a 12.6 ...
A: The A terminal on a Ford generator is on the back of the unit. the two wires on the case are the ...
|
| horn switch won't make horns sound | 7/6/2009 |
Q: The horns on my 1968 Pontiac Catalina do not sound when I press the horn button on the steering ...
A: A bunch of wires comes down the steering column and exits the column just under the dash near the ...
|
| 1964 chevy brakes | 7/6/2009 |
Q: Sears I've got a 64 Impala that I'm having a problem with. It has a power brake unit that did not ...
A: The front wheels would have equal pressure on the ground on each tire and would be stopping the ...
|
| generator light wont go off | 7/6/2009 |
Q: I have a 1962 ford thunderbird . I have a new battery that I purchased last year it holds a 12.6 ...
A: With the engine idling and a voltmeter connected across the battery, jump the field terminal of the ...
|
| 1964 chevy brakes | 7/5/2009 |
Q: Sears I've got a 64 Impala that I'm having a problem with. It has a power brake unit that did not ...
A: In a closed hydraulic system pressure is transmitted throughout the system undiminished. What this ...
|
| 1950 Buick Eight | 7/4/2009 |
Q: I have a 1950 Buick Eight, Motor is completely original It has not been run in about 2 years, before ...
A: If spraying starting fluid into the carburetor did not get at least a burp from the engine it would ...
|
| 1952 Ford flathead v-8 F-1 truck | 7/3/2009 |
Q: I believe my starter bendix is stuck or shot. How the hell do you get this thing out???
A: The starter is held in place by the two long through bolts. The heads are at the opposite end of the ...
|
| steering control valve | 7/3/2009 |
Q: i am working on a 56 gmc 100 truck with power steering, there appears to be an excessive amount of ...
A: Is the play there when the engine is stopped or running? It is normal to have play when the engine ...
|
| fuse box | 6/30/2009 |
Q: where is the fuse box located on 1957 chevy model 210 sedan
A: According to my library 1958 was the first Chevrolet to use a central fuse box and junction box. The ...
|
| worn timming chain | 6/30/2009 |
Q: I have a 1976 Ford with a 360 cubic inch engine.Can a worn or stretched timming chain cause the ...
A: It might. The best simple test for a timing chain is to remove the distributor cap. With a socket on ...
|
| Pinion Seal | 6/30/2009 |
Q: Iam working on a 1966 Buick Wildcat, and I have to change the pinion seal, my question is do I have ...
A: The method that I have used over the years is to center punch a mark on the end of the pinion shaft ...
|
| battery not charging | 6/30/2009 |
Q: My daughter just bought a 66 Ford Fairlane Custom 500. We have put in a new battery,alternator and ...
A: Now that you have spent a bunch of money trying things it is time to break out the voltmeter and ...
|
| 1957 Chevy | 6/29/2009 |
Q: on a recent trip with my 57 Bel Air I started to experience an engine cutting out condition as if ...
A: I think that I would do a vacuum check on the pump and the line. Disconnect the line from the tank ...
|
| Thermostat temperature | 6/29/2009 |
Q: 1966 Oldsmobile Delta 88 425ci 2-barrel. I have a CD manual for my Olds, but it doesn't specify the ...
A: The 195 thermostat appears to be the correct one for the car. The higher temperature thermostats ...
|
| 2003 ford explorer issue | 6/29/2009 |
Q: The gear shift will not come out of park, it is on the column and the wheel will not lock. Can you ...
A: It could be the shift interlock system that prevents the gear shifter to be moved until the brake ...
|
| 65 GALAXIE | 6/25/2009 |
Q: MY DAD HAS A 65 FORD GALAXIE 500. I WANT TO KNOW WHY AREN'T THE TURN SIGNAL LAMPS WORKING? I'VE ...
A: he power for the directional light comes from the ignition switch through a fuse and to the flasher. ...
|
| Brakes | 6/23/2009 |
Q: Do I need to removed the bearing nut to remove the drum? Is there anything unique to replacing the ...
A: The lug bolts will get the wheel off the car and the big nut on the axle end must be removed. To get ...
|
| over tightening carburetor bolts | 6/23/2009 |
Q: I had my '66 Oldsmobile Delta 88 with 2-barrel carburetor in to the corner auto shop today to have ...
A: I am glad that what we auto shop teachers imparted to our students has stuck with some. I spent a ...
|
| 65 chevy | 6/20/2009 |
Q: I have a 65 chevy impala ss with a 327 and my alternator was bad so i put a new one and the bat. and ...
A: First off removing the battery cable with the engine running is not really a good idea. It can cause ...
|
| order on distributor cap | 6/19/2009 |
Q: hey thanks. when looking at the origional distributor cap where do i start from? i thought there was ...
A: Basically Ford used a mark on the distributor car but that is not always accurate. There is more ...
|
| 1962 Comet headlight switch | 6/18/2009 |
Q: How can you remove headlight switch on a 1962 Mercury Comet so you can check the fuses Thanks David?
A: Reach up under the dash. On the side of the headlight switch that is opposite the wires there should ...
|
| Dash lights | 6/18/2009 |
Q: 1969 Ford Falcon Futura station wagon, none of the dash lights work, where should I start my ...
A: There should be a fuse on the back side of the headlight switch. Then check for voltage at the ...
|
| 65 mustang | 6/18/2009 |
Q: I recently purchased a 65 mustang, and let me tell you, shes a beauty, she's got a 351 Windsor ...
A: Will the key turn in the cylinder and does the lock rod appear to be connected inside the door? I ...
|
| 68 bronco wiring probles with turn signals and head lights | 6/17/2009 |
Q: ok I'm stumped here. I had a dash fire recently been re wiring for weeks and all is good except ...
A: The basic on off switches do not have internal wiring necessary to route the circuits to properly ...
|
| 1951 Packard | 6/16/2009 |
Q: I was gifted a '51 packard earlier this year. It has set in a dark garage for over 15 years. Needs ...
A: What you have asked for is an opinion. Please do not give my answer a bad review for an opinion, but ...
|
| brake lights | 6/13/2009 |
Q: I have a 1941 chevy. The tail lights and signal lights work but no brake lights,this is a new ...
A: Ok, the most probable cause is a defective stop light switch. The stop light switch is a hydraulic ...
|
| 1955 cadillac fleetwood | 6/13/2009 |
Q: my horn does not work. i have checked both horns and the are operational.when i hit the horn ...
A: The way that I check a system is to locate and identify the wires on the horn relay. One should be ...
|
| 1957 Buick Century and 1962 Olds Starfire | 6/13/2009 |
Q: I have recently purchased these 2 vehicles, and I was wondering if I should use a lead fuel additive ...
A: I think that you are right on the money. Lead was first used to prevent ping or pre ignition. It was ...
|
| 1957 Buick Century and 1962 Olds Starfire | 6/12/2009 |
Q: I have recently purchased these 2 vehicles, and I was wondering if I should use a lead fuel additive ...
A: You are asking me to put my head in the lions mouth with this question as it is like the "when did ...
|
| 54 belair elec prob | 6/10/2009 |
Q: i recently replaced the starter solenoid and now i am not getting any power anywhere. car will not ...
A: It sounds like you might have mixed up a couple of wires when you put it back together. The cable ...
|
| 1952 chevy pickup | 6/10/2009 |
Q: what kind of lube should be in the steering gear box on a stock 1952 chevy 1/2 ton pickup? I find a ...
A: Gear oil is what was recommended when the truck was new but back in the day the oil seals wore out ...
|
| 1948 Chevrolet Fleetline | 6/9/2009 |
Q: I have a 1948 Chevrolet Fleetline. This car has been sitting for five years so of coarse my battery ...
A: Turning the headlights on to check the battery is not a test of the batteries capacity. The starter ...
|
| 63 FAIRLANE 500 | 6/9/2009 |
Q: ( engine 289 )no gas to carb..... i have replaced fuel pump, fuel lines to tank, taken gas tank off ...
A: Time to get your vacuum gage out. Disconnect the inlet line from the tank at the fuel pump. Install ...
|
| 1937 plymouth brakes | 6/8/2009 |
Q: Looking for someone to tell me how to readjust the brakes on my '37 plymouth. The old shop tools are ...
A: Well sir here is how we did it in the day when one of these came into the shop. If the drum is off ...
|
| 1948 Chevrolet Fleetline | 6/7/2009 |
Q: I have a 1948 Chevrolet Fleetline. This car has been sitting for five years so of coarse my battery ...
A: All GM cars, including Chevrolet, run a NEG ground. You cannot use an 8 volt battery without ...
|
| 1947 olds- thumping from back of car when moving | 6/7/2009 |
Q: I am suspecious of the axle bearing. Any tricks to pulling the axle?
A: This is one of the easy ones to do. Take off the wheel and the brake drum. Behind the axle flange ...
|
| ammeter discharge | 6/6/2009 |
Q: i have a 31 model A tudor sedan. recently the ammeter went from a solid +6 to a steady -2 on the ...
A: OK, I got the picture now. If the battery has at rest 6.2 volts and it will hold that overnight it ...
|
| coil springs | 6/6/2009 |
Q: I have a Modified '55 Chevy truck and want to raise the front end about 2 to 3 inches. I have ...
A: Changing the springs to raise or lower a vehicle is really not the best way to go. This will change ...
|
| 68' Buick 350 Engine running rough | 6/4/2009 |
Q: Im in the process of restoring my 68 Buick but i ran into a problem with the engine. The engine runs ...
A: The first thing that I would do to that engine is to run a compression test. Once that is done and ...
|
| Replacing Coil Springs on 1972 Buick Centurion | 6/4/2009 |
Q: I have a 1972 Buick Centurion with a 445 engine. It has new sensatrac shocks and new bushings on the ...
A: First some of the answer will be opinion and some will be fact so please do not give me a bad rating ...
|
| 51 chevy 216 | 6/2/2009 |
Q: Do you know the valve clearance for a 1951 chevy 216.5 with the motor cold?
A: According to my old note books we were taught at the GM school in Dedham Mass when attending a class ...
|
| 1966 Ford Ranchero | 6/2/2009 |
Q: What is timing setting /point gap for 1966 Ranchero 289? Car starts fine cold ,will not start at all ...
A: Spark plug gap, .034". Point gap, .017". Dwell 26 to 31 degrees. Timing TDC if the engine has an air ...
|
| 66 Ranchero | 6/1/2009 |
Q: What is timing setting /point gap for 1966 Ranchero 289? Car starts fine cold ,will not start at all ...
A: Spark plug gap, .034". Point gap, .017". Dwell 26 to 31 degrees. Timing TDC if the engine has an air ...
|
| generator removel of a 1927 chrysler | 6/1/2009 |
Q: wondering if there are any thing special to remove a generator from a 1927 chrysler, flat head 6 ...
A: I had to go into the way back machine on this one. When i started in the auto biz in the late 1940's ...
|
| 1954 Cadillac series 62 | 5/31/2009 |
Q: i have a 1954 Cadillac series 62 with the 331 the exhaust is all hooked up but i am getting exhaust ...
A: This is called the road draft tube. It vents the crankcase to relieve pressure of blow by in the ...
|
| 235 1955 Chevy Engine | 5/28/2009 |
Q: I've installed this engine (supposedly was rebuilt) in my 49 Chevy. The engine is running a little ...
A: My first though seeing as the two cylinders are right next to each other would be a vacuum leak in ...
|
| Gas and Temp Gauge | 5/27/2009 |
Q: I have a 1964 galaxie 500 and the temp. and gas gauge do not work at all. The car has the original ...
A: The 1964 Ford used a constant voltage regulator mounted on the back of the dash. This takes the ...
|
| clutch noise?? 51 chevy | 5/25/2009 |
Q: i am having a problem with a "growling" noise. tranny was rebuilt and shifts smoothly. rear end has ...
A: As I see it the problem could be the following: The rear bearing area including the snap ring popped ...
|
| brakes | 5/24/2009 |
Q: My 1952 Cadillac brake system will build pressure as I drive. I sometimes have to relieve pressure ...
A: The first thing that I would check is the free play in the bake pedal. If the brake pedal is not ...
|
| 352 | 5/24/2009 |
Q: I know this was a few years back, but I did a search and saw your post on a noise from the lifters. ...
A: The 352 Ford engine was equipped with hydraulic valve lifters unlike its little brother the 332 that ...
|
| Depressurizing A/C on 1968 Firebird 400 | 5/22/2009 |
Q: I just recently started to restore my 1968 Firebird 400. I am working to pull the engine and I need ...
A: It is illegal to dump R 12 into the atmosphere. The refrigerant must according to law be removed ...
|
| 1967 mustang convertable 289 | 5/21/2009 |
Q: When we turn the wheels sharp on our car the pressure line to the power steering rubs on the frame ...
A: Two things come to mind, first check and see if there is a brand label or mark on the headers. Then ...
|
| brake drum removal - 1947 Lincoln Continental | 5/20/2009 |
Q: I am trying to remove the right rear axle on a 1947 Lincoln Continental. I understand I have to ...
A: The last cars that used this type of tapered fit between the axle and the hub were produced in the ...
|
| 1972 Cutlass Supreme | 5/18/2009 |
Q: Recently I purchased a '72 Cutlass from a private dealer in Michigan knowing full well that it was ...
A: I would rewire the unit the correct way with a 10 ohm resistor available from radio Shack and then ...
|
| 1972 Cutlass Supreme | 5/18/2009 |
Q: Recently I purchased a '72 Cutlass from a private dealer in Michigan knowing full well that it was ...
A: The SI series alternator by Delco is equipped with an internal voltage regulator. When retrofitting ...
|
| '67 Bonneville Engine Rattling Sound | 5/18/2009 |
Q: I have a 1967 Pontiac Bonneville with a 400 V8 engine. After the car is started and reaches ...
A: I'll bet you have a chirpy belt. Stick your thumb nail into the belt running surface. It should ...
|
| '67 Bonneville Engine Rattling Sound | 5/17/2009 |
Q: I have a 1967 Pontiac Bonneville with a 400 V8 engine. After the car is started and reaches ...
A: The test that I use for timing chain stretch is simple and requires only removing the distributor ...
|
| carburetor | 5/16/2009 |
Q: how do i adjust carb on a 87 cutlass supreme 307,5.0,y series. it is running to rich.
A: There is no simple adjustment for this carburetor.It is an electronic carburetor that is controlled ...
|
| oil leak rear main | 5/16/2009 |
Q: hey brad!hello let me tickle your brain"i have a 1950 chevrolet styleline deluxe that i personally ...
A: End play is fine as is the oil pressure. Before you pull the engine check the crankcase venting ...
|
| 1963 ford galaxy overdrive wireing | 5/16/2009 |
Q: do you know what the proper wiring configuration is for my car. it has overdrive but the wires ...
A: Under the car there should be one connection to the governor on the overdrive case and two to the ...
|
| 1940 plymouth | 5/14/2009 |
Q: I have a 1940 plymouth that has not been started in at least 10 years. I have driven the car before ...
A: My routine for these Rip Van Winkle cars is as follows provided that the engine will turn over and ...
|
| Electric conversion-6 to 12 volt | 5/14/2009 |
Q: I have a 1941 Plymouth pickup. If I convert to a 12 volt system, do I have to used a 6 volt reducer ...
A: As far as the ignition system goes you need to install a 12 volt ignition coil. There are two types, ...
|
| 1964 AMC American Rambler | 5/14/2009 |
Q: I have a 1964 AMC American Rambler and I am trying to figure out if i have the generator hooked up ...
A: The generator system on your car should be a Deco Remy with two wires going from the generator to ...
|
| Fordomatic auto transmission speedometer | 5/14/2009 |
Q: I have a 55 Ford Fairlane with a fordomatic 2 speed automatic transmission, I removed the ...
A: Back in that era I worked for Ford as a trainer. The official company line was to remove the ...
|
| oil leak rear main | 5/13/2009 |
Q: hey brad!hello let me tickle your brain"i have a 1950 chevrolet styleline deluxe that i personally ...
A: Do you have a high pressure/volume pump in this engine or have the oil pressure relief spring ...
|
| 1940 p-10 oil filter pressure | 5/13/2009 |
Q: line connect that is on the vacuum at the underside of the distribute the steel line is in a box of ...
A: The case of the oil filters blowing up and leaking sure sounds like high oil pressure and a stuck ...
|
| '51 Cnev timing mark | 5/12/2009 |
Q: Expert Brad Spears Responded to my question regarding the timing mark location on the crankshaft ...
A: It would appear that on your engine the key way and the timing mark are the same on the crank gear. ...
|
| 1102043 Delco Remy Generator | 5/10/2009 |
Q: My father-in-law is rebuilding a 1957 Corvette. He has a generator and would like to know if it ...
A: I have never seen any specifications for ohms of resistance across a generator for bench testing. ...
|
| oil leak rear main | 5/10/2009 |
Q: hey brad!hello let me tickle your brain"i have a 1950 chevrolet styleline deluxe that i personally ...
A: A couple of things come to mind. First the rear main seal is only to get rid of the little bit of ...
|
| poor performance | 5/8/2009 |
Q: i have a 1959 chevy truck with a 235 6, it has been a great truck, recently, it has no power under ...
A: It could be any one of the following list of things: Fuel filter Bad Fuel pump Plugged exhaust Bad ...
|
| Transmission pan gasket | 5/6/2009 |
Q: I have a 1972 Plymouth Fury with a A727 Tranny. Pan gasket leakes,have changed it twice,still leaks. ...
A: It is either bent, has a hole in it or there is something above it leaking and running down to the ...
|
| 1981 pontiac bonneville 3.8 | 5/4/2009 |
Q: Yesterday my car was running. Yes the oil light came on when you came to a stop but the oil was ...
A: The first thing that I would do now is to get a compression check on the engine. That will tell you ...
|
| Ignition tumbler | 5/4/2009 |
Q: I have a new tumbler for my 1963 Nova and can't get the old one out. I've tried inserting a paper ...
A: If I remember right you turn the switch to the accessory side, counterclockwise, and then insert the ...
|
| 1950 Ford Truck Carburetor | 5/3/2009 |
Q: I have a 1950 Ford Truck original in line 6 cyl.with original one barrel carburetor. The needle ...
A: Somewhere in the 1950's the carburetor and carb kit makers began using a material called Viton on ...
|
| 41 chevy leaking rear seal | 5/3/2009 |
Q: I have a 41 chevy 216 has a leaking rear seal,the shop has replaced twice already yet it still is ...
A: There are several oil galley plugs behind the flywheel that can leak. When they do they drip down ...
|
| 1973 Mustang Mach 1 - Oil Pressure Low | 5/3/2009 |
Q: Oil pressure is below Low. Thought I would change the oil, was about to fill, and the filler cap ...
A: The white emulsion indicates water in the oil. There are several possible sources. One is a blown ...
|
| exhaust backfire | 5/2/2009 |
Q: 52 Chevy Pickup 216, Backfires in exhaust on acceleration. Timing, points plugs OK. Will engine ...
A: Several things can cause this. Before I went to valve adjustments I would check the distributor cap ...
|
| thermostat on 68 t-bird | 5/2/2009 |
Q: Hey- I'm wondering where the thermostat is on my car and how I can check to see if it's working ...
A: On your car at the engine end of the upper radiator hose there is a connection/housing that is ...
|
| 1961 Econoline kingpins | 5/2/2009 |
Q: I have a friend who is not computer literate but needs some information on changing kingpin bushings ...
A: There should be a lock bolt through the axle stub end that locks the king pin in place. It is a ...
|
| power drum brake problem, | 4/30/2009 |
Q: I have a 66 mustang coupe with drum brakes. I put power brakes on it and now when the brake pedal ...
A: Well this is going to be a full check of the braking system. I have one more question. Were the ...
|
| 1981 F100 won't stay running | 4/30/2009 |
Q: I have a 1981 Ford F100 300 L6, hasn't ran since about mid-2000. This past weekend replaced the ...
A: The reason for the question of the running with the key held in the start position, there is two ...
|
| 1940 chev coupe electrical | 4/30/2009 |
Q: what do I need to do to convert the electrical starting system to 12 volts? ANSWER: Are you just ...
A: Doing this is more difficult that converting the entire system. The starter motor won't know the ...
|
| eletrical | 4/28/2009 |
Q: i have recently purchased an 1991 dodge d-150. the engine and tranny have been replaced,everything ...
A: The speedometer is electronic in this truck. The speed sensor sends a signal to the engines ...
|
| 1939 buick eight special | 4/25/2009 |
Q: Im haveing a problem removing the radiator, I expect that the front fender and grill must come off, ...
A: The radiator can be removed without removing the front fenders. Remove the hood, disconnect the ...
|
| 1968 buick wildcat | 4/23/2009 |
Q: i cracked the ring ledge on a piston in the number three cylinder. a compression and leak down test ...
A: If you have a damaged piston the engine should come apart. There is no way to determine if the ...
|
| lincoln carb tag | 4/23/2009 |
Q: i got a Lincoln 1977 town car and the carburetor is not running good. the thing is that i want to ...
A: 9510 defines the part number as a carburetor. The D7 indicates that the first year thyat this ...
|
| Trans tool | 4/20/2009 |
Q: I own a 57 Mercury Montclair with a Merc-O-Matic transmission.The Manual calls for specific tools to ...
A: Check E-Bay there is the tool for one of the band adjustments on there right now. ...
|
| 1979 chev 1/2 ton pick-up | 4/19/2009 |
Q: Do 1979 chevey 1/2 ton custom deluxe 350 v8 pick-ups have fuel filters, and if so where are they ...
A: The diagnostic route that I would take is as follows: 1. Check the inlet side of the for vacuum when ...
|
| 76 ford bronco | 4/19/2009 |
Q: I just installed new plug wires & now it back fires, I probably mixed a couple of wires, looking for ...
A: The distributor cap should be marked with a number 1 between the center coil tower and one of the ...
|
| 1979 chev 1/2 ton pick-up | 4/18/2009 |
Q: Do 1979 chevey 1/2 ton custom deluxe 350 v8 pick-ups have fuel filters, and if so where are they ...
A: If the truck is stock and has not been tampered with the fuel filter is located in the carburetor ...
|
| wiring problem | 4/17/2009 |
Q: Brad, The rear wiring harness on my1973 MGB is getting hot and smoking whenI turn the ingition on. ...
A: Mike, you are going to need to do some 007 type work on the machine. It is time for a visual ...
|
| 1965 289 mustang fastback overheating | 4/16/2009 |
Q: the engine gets very hot at highway speed. At idle and cruising at 40 mph the temp is normal. The ...
A: It sounds very much like a partially plugged radiator. There is enough flow to remove the heat from ...
|
| powerglide transmission faliure | 4/15/2009 |
Q: we have fitted a second hand ( first mistake ) alloy powerglide to our '55 chevrolet after the ...
A: The parking pawl is connected to the output shaft inside the transmission. because you have a ...
|
| 1940 plymouth start up | 4/12/2009 |
Q: I have purchased a 1940 up-10 deluxe sedan and know that the car has not been started in 18 + years ...
A: My routine for these Rip Van Winkle cars is as follows provided that the engine will turn over and ...
|
| 10 Volt Battery | 4/12/2009 |
Q: The engine has an old 10 Volt system and battery. When charging the battery should I set the charger ...
A: A battery charger usually puts out 2.33 volts per cell. that means that a charger for a 12 volt ...
|
| The brake system on a 1958 Cadillac 62 series | 4/12/2009 |
Q: I sure hope you can help me,I bought this car a few weeks ago and the brakes are out,the first thing ...
A: The brake system is called Treadle and was made by Bendix. The only external cause of the pedal ...
|
| 196? Ford Mustang | 4/11/2009 |
Q: The woman I bought it from told me that is was completely original with nothing done to it. It has ...
A: Try the following web sites: http://www.autoinsurancetips.com/mustang_vin.htm ...
|
| LOW BRAKE PEDAL | 4/10/2009 |
Q: 1962 FORD THUNDERBIRD HAS A LOW BRAKE PEDAL AFTER COMPLETE BRAKE JOB AND BLEEDING AT LEAST 3 TIMES. ...
A: I would start by removing all the wheels and drums to be sure that all of the wheel cylinder push ...
|
| 1966 Plymouth Fury III (318) Overheating | 4/10/2009 |
Q: I bought an old '66 Plymouth Fury III with a 318 last year and I've slowly been trying to restore ...
A: It sounds to me more like a partially clogged radiator than anything else. If the head gasket was ...
|
| 1966 Plymouth Fury III (318) Overheating | 4/10/2009 |
Q: I bought an old '66 Plymouth Fury III with a 318 last year and I've slowly been trying to restore ...
A: Ok, the easy check for coolant in the oil is to take the engines dip stick with oil on it as pulled ...
|
| Band adjustment | 4/9/2009 |
Q: I have a "58" Impala with the cast iron powerglide transmission. Is there a simple way to check for ...
A: The low band adjustment screw is on the left side of the transmission case. Loosen the lock nut and ...
|
| Powerglide Transmission | 4/8/2009 |
Q: I am changing the transmission fluid in my "58" Impala with the cast iron powerglide. I drained the ...
A: Back in the day there were those mechanics that drilled a hole in the converter case, and threaded ...
|
| 1958 biscayne speedometer not working, installed new cable. | 4/8/2009 |
Q: I have 58 biscayne 235 and the center drive shaft bearing is out. I was wondering what tools one ...
A: Take the end of the cable off the speedometer head and leave it connected to the transmission. Jack ...
|
| 1966 Mustang horn | 4/8/2009 |
Q: The horn for my 66 Mustang works...barely. When I push the horn it almost seems it takes a minute ...
A: I have done this many times and sometimes it works and some times it does not. The cover over the ...
|
| timing chain cover on 94 Berretta with 6 | 4/7/2009 |
Q: How do I replace broken timing chain cover without breaking it. It looks as if you need to pry on it ...
A: The recommended proceedure for replacing the front cover involves removing the oil pan. The oil pan ...
|
| lincoln carb tag | 4/6/2009 |
Q: i got a Lincoln 1977 town car and the carburetor is not running good. the thing is that i want to ...
A: The best numbers that I can come up with are as follows: The standard carburetor is part number ...
|
| 67 Camaro | 4/6/2009 |
Q: I recently did a complete renovation of an RS/SS with a 350 engine. Included in the renovation was a ...
A: Do you have an electric fuel pump on the car? It sounds like the carburetor is flooding over and it ...
|
| 1968 camaro startup problem | 4/6/2009 |
Q: My 327 was rebuild to GM specs. when I set the timing dwell and rpms I set them to specs. the carb ...
A: If it runs good when started it does not sound like advancing the timing is the right move. I would ...
|
| monte carlo ss | 4/6/2009 |
Q: i have a 1985 chevy monte carlo ss my hubby replace engine with 350 it has a edelbrock carb ...
A: Do you have the computer hooked up and functioning or did he attempt to bypass it? If the computer ...
|
| 54 bel-air closed driveshaft.. | 4/5/2009 |
Q: My dad has a 54 Bel-Air 2dr. sedan..235 w/3spd. The tranny is really noisy and he wants to convert ...
A: You are right, he would have to change the rear end as well. Street rodders do this all the time and ...
|
| 1991 Pontiac Trans Am, Rough Running | 4/2/2009 |
Q: After taking our Trans am out of its winter sleep and giving it a general once over it was time to ...
A: The first thing that I do to any computer equipped car with a running problem is to hook up a ...
|
| 1950 Chevy pickup | 4/1/2009 |
Q: I have a 1950 chevy pickup mostly original. 3 questions are: #1 The starer turns over slow even when ...
A: 1. Time to have the starter tested and check all the connections including the ground side. If the ...
|
| Air in the diesel line? | 4/1/2009 |
Q: I just bought a 76? Leyland Sherpa b series diesel and it looks great.Before I bought it it the ...
A: Jason, air can only enter a system in an area that is not pressurized. That said I would check the ...
|
| light switch | 3/29/2009 |
Q: how is a light switch for a 68 gto removed from the dash?
A: Behind the dash on the side of the switch there is a spring loaded button. Depress this button and ...
|
| No turn signal 1959 Rambler | 3/28/2009 |
Q: I have just bought a 1959 Rambler with a 196 LE six cylinder and the turn signals do not work. How ...
A: The first check is the fuse. If the fuse is good then with a test light check for voltage at the ...
|
| Fuel Pump Relay 1982 Corvette | 3/25/2009 |
Q: Could a bad fuel pump relay cause the engine not to crank? My fuel pump will run continuously with ...
A: This is not normal. The fuel pump should turn on for about 2 seconds to load the system when the key ...
|
| spedometer cable | 3/24/2009 |
Q: I recently bought a 1971 ford f-100. The spedometer and odometer are not functioning. When I check ...
A: It should be a straight forward replacement. Be aware that the gear at the transmission end of the ...
|
| pontiac trans am | 3/19/2009 |
Q: whining noise when decelerating
A: A whining noise when decelerating coming from the rear of the car usually indicates a bad pinion ...
|
| themrostat | 3/19/2009 |
Q: I own 72 Buick skylark 455.I'm changing new thermostat,Do i need to put gasket sealer on gasket or ...
A: You should replace the gasket and nothing goes on the bolts. Clean the threads as they trend to gunk ...
|
| inside of tire rubbing | 3/18/2009 |
Q: hey i have a 66' ford mustang and i don't know much anout fixing this. the inside of my front ...
A: There are several reason for this to happen. First is the wrong rim and tire on the car. Second ...
|
| 1969 Ford F150 Pickup | 3/16/2009 |
Q: My husband's pickup has siezed exhaust manifold bolts on the underneath side. He has tried heating ...
A: OK, if I were doing this job at home here is how I would proceed. First I would wash the engine down ...
|
| 1970 Cadillac Coupe Deville | 3/12/2009 |
Q: I would like to know how to go about changing the alternator on a 1970 Cadillac Coupe Deville? ...
A: Sound like old age has set in and the hose has lost it's flexibilty. It might have to be ...
|
| Dim Headlights | 3/11/2009 |
Q: I have a 1938 Dodge with updated running gear. Alternator and battery are good but headlights are ...
A: It sound like a bad ground on the head light system. Check all the connections. Not just for ...
|
| Dual water pumps on a 46 Mercury | 3/10/2009 |
Q: Greetings Brad! A friend just picked up a Convertible 1946 Mercury and is having some engine ...
A: Sorry for the delay but we are traveling in search of warm. We are right now just north of Orlando ...
|
| Dual water pumps on a 46 Mercury | 3/9/2009 |
Q: Greetings Brad! A friend just picked up a Convertible 1946 Mercury and is having some engine ...
A: I am a bit confused. Are the water pumps mounted to the cylinder heads or the engine block? Are the ...
|
| oil pressure gauge | 3/9/2009 |
Q: I have a 1974 Corvette with electric oil pressure gauge the needle stays at 80 psi., with engine ...
A: with the key off the sender would be out of the loop. Sounds like the needle is stuck. To be sure ...
|
| timing. | 3/9/2009 |
Q: I have a 1954 chevy 210 with a 235CI 6. I recently installed a Pertonix ignitor cause the popints ...
A: It sounds like the needle valve under the float is leaking by, either worn out or dirt holding it ...
|
| 1940 Plymouth master cylinder. | 3/8/2009 |
Q: I have three questions regarding a 1940 Plymouth Deluxe P10. 1. The master cylinder has 2 ports, a ...
A: If the car is equipped with the original master cylinder all four brakes are connected to the one ...
|
| 1970 Cadillac Coupe Deville | 3/8/2009 |
Q: I would like to know how to go about changing the alternator on a 1970 Cadillac Coupe Deville?
A: The first thing to do when replacing an alternator is to disconnect the battery. The large wire on ...
|
| my 68 firebird (original 400 big block motor) isn't getting fire to the engine | 3/7/2009 |
Q: i have changed the complete firing coil and have changed the spark plugs... i really dont know much ...
A: The ignition module and the pick up coil in the distributor are two likely causes of no spark. The ...
|
| 51 Pontiac 8 | 3/2/2009 |
Q: I have a problem with my flathead straight 8. It has recently been converted to 12v. 1): it is ...
A: I am not a fan of converting to 12 volt and if not done correctly can cause these problems. The ...
|
| Plug Wire Diagram | 2/28/2009 |
Q: I am currently restoring a 1977 Pontiac Firebird Trans Am (6.6L 400 V8 4spd-man). I Just bough new ...
A: Check the following article. It has a good step by step description for making sure that the plug ...
|
| ELETRICAL WIRING HARNESS | 2/27/2009 |
Q: I OWN A 1969 MACH 1, AND SINCE THE CAR IS SO LOD I WAS THINKING ABOUT REWIRING THE WHOLE CAR FROM ...
A: Get a copy of Hemmings Motor News the old car hobby bible for classified ads for old car parts. ...
|
| white smoke | 2/25/2009 |
Q: bought a 1954 caddy was stored for 16yrs and never run. Got it running, after about 20 minutes ...
A: Are you loosing coolant? White smoke is usually an indication that coolant is getting into the ...
|
| 69 ford failane 302 | 2/23/2009 |
Q: rebuilt engine 302 30 thousand bore stock new rad pump therm gets hot idling it keep going up and up ...
A: Two things come to mind. First, the thermostat could be installed upside down. Second, make sure ...
|
| 1929 Packard 645 backfire | 2/22/2009 |
Q: I have a 645 D/C Phaeton. Engine rebuilt prox 3000 miles ago. It's been running great since fuel ...
A: One beautiful car! the carburetor needs to be removed and opened up. If you have only two thumbs (my ...
|
| Switching to Air Suspension for Smoother Ride | 2/18/2009 |
Q: I have a 1972 Buick Centurion (455 stage 1 engine. Vehicle weight approx 4500 pounds), which has ...
A: Changing the ride characteristics of a car is more tan just bolting on some extra parts. Your ...
|
| 1965 Mustang C4 transmission decoding | 2/14/2009 |
Q: I have just purchased a 1965 Mustang 2+2 Fastback and I am trying to decode some of the numbers I am ...
A: From my days as an old Ford service manager the C stands for the 1960's. The 6 stands for the model ...
|
| coil input voltage | 2/12/2009 |
Q: I have a 1967 Ford F-250 4X4 truck. I recently converted it to a 300-6 motor from the horrible 352 ...
A: Do you have electronic ignition or points? If points,and you ran the engine without a resistor, I ...
|
| Battery 33 pontiac | 2/11/2009 |
Q: Is my 33 pontiac with straight a positive or negative ground. I have heard both. Having problems ...
A: As far as I know it is neg ground. The best way to tell is to hook up the battery with neg ground ...
|
| '64 bonneville auto transmission | 2/9/2009 |
Q: I just bought a '64 bonneville with the dual coupling trans(or whatever gm called it) the problem ...
A: A transmission oil change and a filter would be my first move and then put shoe miles on the car to ...
|
| 1965 Mustang C4 transmission decoding | 2/4/2009 |
Q: I have just purchased a 1965 Mustang 2+2 Fastback and I am trying to decode some of the numbers I am ...
A: Try the following web sites: ...
|
| crack | 2/4/2009 |
Q: I just rebuilt a 350 chevy small block. When I screwed in the three oil plugs behind the flex plate ...
A: I have, on my own engines not customers, used a two part epoxy fix. Do not remove the plug. At the ...
|
| '74 Dart - Won't idle and dies without giving gas | 1/21/2009 |
Q: My 74 Dodge Dart Swinger w/ slant6 starts fine but dies once I take my foot off the gas. Likewise ...
A: It sounds like it could be the Exhaust Gas recalculation valve (EGR). It is located on the intake ...
|
| 1954 Chevy 210 w 235Ci and powerglide | 1/20/2009 |
Q: I have a 235Ci engine with a power glide trans. At Idle and reving in the drive way she performs ...
A: noel you are probably on the right track thinking fuel pump. However I would start with a fuel ...
|
| Crack in Cyl block | 1/19/2009 |
Q: I have a 1927 chevrolet engine with a crack in the block and wanted to know how to repair it. Do ...
A: This is one of those questions that has no real right answer, it depends on what the person ...
|
| dieselengines | 1/15/2009 |
Q: how long should you idle the turbo diesel engine before shutting it down?
A: That depends on what the engine maker says in the owners manual. In my Detroit engined motor home, I ...
|
| i have water in my oil | 1/15/2009 |
Q: i own a 1999 chevy suburban 4x4 350 small block. i had my oil changed about 3 weeks ago. shortly ...
A: It sounds like the probability of a blown or leaking head gasket. It is time for a radiator pressure ...
|
| 1966 T-Bird gas tank | 1/11/2009 |
Q: my owners manaul as well repair shop book says the tank is 22 us gall. tank however when i go to ...
A: Joyce, you will have to ask the people reproducing the tank why that is. It could be that they say ...
|
| 67 mustang upper ball joint | 12/29/2008 |
Q: what is the procedure you would do to replace the upper ball joints for a 67 mustang.they are four ...
A: Get a manual for this car. The upper control arm needs to be supported before the big nut on the ...
|
| starting an old car | 12/27/2008 |
Q: I have a 78 dodge colt that has been sitting out in the weather for about 5 years, not prepared for ...
A: We just came through the San Francisco area two weeks ago in our motor home. Enjoyed our visit and ...
|
| Question on electrical wiring - '64 F100 PU | 12/22/2008 |
Q: Brad, Recently, I was under my 64 Ford F100, looking over the electrical wiring that runs back to ...
A: I think you might have created a problem. each wire needs to be repaired with tape covering the bare ...
|
| 1970 351 Cleveland 4V. Oil in radiator. | 12/20/2008 |
Q: Last March my wife and I took the plunge and bought our 1st muscle car, a 1970 Mercury Cougar. It ...
A: There are several ways to uncover the problem. One is use a carbon monoxide detector on the ...
|
| 68 cougar overheating | 12/17/2008 |
Q: Our 68 cougar was overheating so I replaced the thermostat and had the radiator rebuilt with a new ...
A: THERE IS SUPPOSED TO BE A SPRING INSIDE THE LOWER HOSE. THE LOWER HOSE IS THE INTAKE SIDE OF THE ...
|
| 68 cougar overheating | 12/16/2008 |
Q: Our 68 cougar was overheating so I replaced the thermostat and had the radiator rebuilt with a new ...
A: The water pump and the thermostat come to mind in this case. The lower radiator hose could be ...
|
| 68 cougar overheating | 12/14/2008 |
Q: Our 68 cougar was overheating so I replaced the thermostat and had the radiator rebuilt with a new ...
A: Ok Jim, I need some answers to a couple of questions so that I can give you the right diagnosis. ...
|
| No engine compression | 12/14/2008 |
Q: I have a 33 Pontiac straight 8 all cylinders but one have good compress. That one has no ...
A: That sweet old Pontiac 8 was about the smoothes running engine on the road in it's day. That became ...
|
| valve adjustments | 12/12/2008 |
Q: the valves on my pontiac 400 have started to chatter a bit, it might be because I lost some oil ...
A: The valve lifters are the things that run on the cam and the push rods set in the cup on the top of ...
|
| Chevy 454 dieseling problem | 12/11/2008 |
Q: We recently purchased an old motor home ('86) and am very happy with operations, except for a ...
A: I assume that you are talking about after run when you shut the engine down. The main cause is a ...
|
| !978 Corvette wont start | 12/10/2008 |
Q: I'm having a problem with my 78 Corvette Pace car that will not start. It has an L48 350 motor with ...
A: Ok, an engine needs three things to run, fuel, compression, and spark. Since you smell fuel and you ...
|
| 1984 GMC Sierra 2500 | 12/8/2008 |
Q: Mr. Sears, I've had older autos in the past and am comfortable with turning a wrench. I recently ...
A: The chirping noise is probably an exhaust manifold leak under power. A little kerosine down the ...
|
| flathead over heating | 12/8/2008 |
Q: Brad, I have a 1953 Ford Customline w/ flathead V-8. I've read in "thnder Road", that enhanced ...
A: My thought is NAY. For a steet stock engine if the radiator is clean and the head gaskets are not ...
|
| 1962 Impala Data Plate | 12/6/2008 |
Q: I am restoring a 1962 impala sport coupe and need to decode the manufacturers data plate to ...
A: For paint codes, http://www.xframechevy.com/pictures/1408.htm For body style, ...
|
| 1936 ford philco radio | 12/6/2008 |
Q: how hard would it be to leave the original face, knobs etc, and put in a new updated radio under the ...
A: I have a modern radio in the glove box of my 41 Ford. There are companies that specialize in ...
|
| fuel pump reinstallation | 12/4/2008 |
Q: On my Jaguar XJ12L I had to depressurize the fuel pump by disconnecting the 85 terminal of the fuel ...
A: If the pump was working why did you replace it? In this case I would get my trusty test light or ...
|
| 1939 ford deluxe steering wheel removal | 12/3/2008 |
Q: I can't figure out how to remove the steering wheel on my 1939 Ford Deluxe. The service manual I ...
A: At the base of the steering box under the hood you will find the headlight switch. Iyt is held on to ...
|
| oil pan remove 1970 dodge dart | 12/2/2008 |
Q: is there any way to remove an oilpan from a 1970 dodge dart 6 cylinder i work out of my house garge ...
A: There is no easy way to remove the oil pan on a six cylinder engine. We almost always lifted the ...
|
| 1965 Plymouth belevedere Horn | 12/1/2008 |
Q: Hi Brad I can't get my horn to blow---It has all new parts inside the steering wheel Ypu can get ...
A: The control wire from the relay goes up though the steering column and the horn switch in the column ...
|
| fuel gauge on 1967 plymouth gtx | 11/30/2008 |
Q: FUEL GAUGE DOES NOT REGISTOR PROPERLY NEW TANK & SENDING UNIT INTALLED GAUGE ONLY GOES TO HALF ...
A: On the fuel tank when I have this problem with an older car I usually drop the tanks. Remove the ...
|
| locked braks 1935 Oldsmobile | 11/29/2008 |
Q: I backed my 1935 olds into the garage. It sat for a year. Both rear wheels are locked. The front ...
A: If you have room to back the car up some times this will free up the cables. Short of that the only ...
|
| 64 Belair seatbelts | 11/26/2008 |
Q: Did GM provide rear seat-belt mounting points on the 64 belair?
A: Not that I know of. The last seat belts that I installed in the rear of an old car, I used after ...
|
| 1967 GTO vibration | 11/25/2008 |
Q: Vibration starts above 55 mph and stays about the same up past 70. Seems to come up through body as ...
A: Try something for me. Drive the car at low speeds on a smooth straight surface, say 10 to 20 miles ...
|
| Generator Polarizing | 11/22/2008 |
Q: I sent my generator out for repair and will be picking it up tomorrow. 12 volt Delco for a willys ...
A: With a jumper wire flash the "B" battery and "A" armiture terminals on the voltage regulator. This ...
|
| 1986 Chevy C-10 262 V-6 emission controls | 11/20/2008 |
Q: In the process of replacing the thermostatic vacuum switch inside the air cleaner, I lost track of ...
A: Motors Auto Repair manuals published some good emissions books in the day. I have had luck finding ...
|
| 1968 cougar | 11/20/2008 |
Q: My 1968 mercury cougar (302 4bl) is running rough and stalling out. On the highway it will back ...
A: To get the specs for your engine go to web site ...
|
| 1986 Chevy C-10 262 V-6 emission controls | 11/20/2008 |
Q: In the process of replacing the thermostatic vacuum switch inside the air cleaner, I lost track of ...
A: Have you looked under the hood for the factory installed emissions decals? They are mandated by ...
|
| Chev fuel pump | 11/18/2008 |
Q: Should fuel pump pressure drop when engine starts? When key is turned, pressure is about 58 lbs. It ...
A: The pressure will drop with the engine idling and go up when the engine is not running or you stomp ...
|
| 1984 Chevy 305 Small Block | 11/17/2008 |
Q: Need a 2nd opinion...My recent acquired 84 Chevy occasionally dumps a small amount of anti-freeze ...
A: If the car does not have an overflow tank, then over filling the radiator when the engine is cold ...
|
| 41 Ford two-door sedan rear brake drum removal | 11/17/2008 |
Q: The right rear brake drum is stuck. I have tried using at the same time a propane torch to heat ...
A: A good heavy duty drum puller is tighten by whacking it with a heavy hammer. Once you get a good ...
|
| 1984 Chevy 305 Small Block | 11/17/2008 |
Q: Need a 2nd opinion...My recent acquired 84 Chevy occasionally dumps a small amount of anti-freeze ...
A: Before attacking it as a head gasket problem I would try a replacement radiator cap. It could very ...
|
| idle 2000 gt mustang 4.6 | 11/17/2008 |
Q: my 2000 gt mustang 4.6,runs an idles normally,when you turn on the heater or the air condition,then ...
A: You are going to have to get into the computer operation and the sensors on this one. When you throw ...
|
| 235 chevrolet engine | 11/15/2008 |
Q: I have a 1958 chevrolet 235 engine, all original including carb, distributor, ignition, etc. It is ...
A: It sounds like it is running out of fuel. The cause could be a bad fuel pump, a fuel filter is so ...
|
| Custom Bel Air, but not any more... | 11/15/2008 |
Q: I am currently thinking about buying a very old Chevy Bel Air from my grandfather and customizing ...
A: Here is what I would do. I would start reading the hot rod and street rod magazines. They are ...
|
| 1939 Plymouth sedan wiring | 11/13/2008 |
Q: It's time to re-wire my 39 plymouth I haven't re-wired a car before and wanted to know should I look ...
A: There are several wiring companies that make excellent kits for your car. A universal kit will not ...
|
| Custom Bel Air | 11/10/2008 |
Q: I am currently thinking about buying a very old Chevy Bel Air from my grandfather and customizing ...
A: Anything is possable with welding equipment and metal fabrication tools. As to what parts to use and ...
|
| 64 dodge dart 270 | 11/9/2008 |
Q: How are you. I just purchased a 1964 Dodge Dart 270 4dr with a 225 slant 6. The person I purchased ...
A: Something is real squirrely here. Just adding new gas should not make the car smoke and adding lead ...
|
| training -young talent into craftsmen | 11/9/2008 |
Q: Brad,I have been in the classic car restoration business for 30 some years and have been training ...
A: Doug, I wish that I had this question two weeks ago as we passed through Lincoln and I would have ...
|
| 1966 Mustang Convertible 286 Engine--Road-ready after 12 years | 11/6/2008 |
Q: I need to move a 1966 Mustang from one state to another-- then, have a mechanic work make the ...
A: Susan, I would need to know the running condition of the car when stored and how it was prepared for ...
|
| 1956 Tbird stalling | 11/3/2008 |
Q: My 56 Tbird stalls out after driving 5-10 miles. I then can restart it, usually right away but it ...
A: Sounds very much like a plugged fuel filter or a weak fuel pump. I assume that it stalls as you are ...
|
| System not charging:Part 3 | 11/3/2008 |
Q: ANSWER: Are you comfortable using a volt ohm meter and if so do you own one? Let me know and I will ...
A: First of all check the grounds between the body and the engine. Then make sure that the voltage ...
|
| 71 ford starter | 10/16/2008 |
Q: how to change bendix spring ANSWER: The 71 Ford did not use a Bendix spring in the starter. Tell me ...
A: Good, that is the easy one to do. Remove the starter from the car and take out the two thru bolts. ...
|
| Rear drum removal 1954 Coronet | 10/16/2008 |
Q: I can not remove the rear drums on my 1954 dodge coronet. I am using a heavy duty puller that you ...
A: One little trick to using one of those pullers is to smack the end of the puller screw pretty hard ...
|
| holly 94 float level setting | 10/15/2008 |
Q: i have a 1936 ford with a ford{Holly} carburettor markings on side say ford also has a 94 and a ...
A: Ok, the way we did it in the day when i worked for Ford was to bench set the float level with the ...
|
| 71 ford starter | 10/14/2008 |
Q: how to change bendix spring ANSWER: The 71 Ford did not use a Bendix spring in the starter. Tell me ...
A: There are two different starters that could be used on your car. One has a solenoid on the starter ...
|
| solenoid conversion | 10/14/2008 |
Q: Please disregard last nights response to your question back to me about 3 or 4 lug solenoid. My ...
A: Sorry for the delay, but time just gets away from me. The two small terminals should have a letter ...
|
| generator | 10/11/2008 |
Q: could you advise me on how to do this, i know nothing about it, i was driving home and the gen light ...
A: If the generator was still on the car the test to determine regulator or generator is simple. Just ...
|
| 66 Mustang | 10/10/2008 |
Q: The fuel guage on my mustang does not work. stuck in the middle, but can go up to full but doesnt' ...
A: Disconnect the wire from the fuel gage to the sending unit. Ground the wire with a jumper. Turn on ...
|
| 1938 Pontiac Opera Coupe 6 cylinder | 10/10/2008 |
Q: Having the air cleaner off I started the car and what looks like white smoke was coming from the ...
A: There are three explanations that come to mind. All three are exhaust. First thought is that there ...
|
| MG Midget ignition problem | 10/8/2008 |
Q: I have a '76 Midget that I restored and rebuilt the engine a couple of years ago. I store the car ...
A: If you have a voltmeter connect it to the coil terminal that goes to the points. Remove the ...
|
| Heater and Window defrosters | 10/8/2008 |
Q: I recently bought a 1947 ford super deluxe w/ a V-8 Orginal.It has a different heater than any I ...
A: Good morning Ralph: A couple of questions please. The duct that runs forward on the hood, is it ...
|
| 1958cj5 | 10/7/2008 |
Q: I have replaced sparkplugs and wires, coil, battery, points, condenser,rotor and cap. |One cylinder ...
A: Several things come to mind. I believe that there is a vacuum take of on the intake manifold right ...
|
| electrical problem 1975 Plymouth Scamp | 10/5/2008 |
Q: My issue is that I have a 1975 Plymouth Scamp with a slant 6. Recently when the headlights are on ...
A: In that era Chrysler built cars had a lot of problems with the main wiring harness connector that ...
|
| 1971 el camino | 10/4/2008 |
Q: I just bought a 1971 el camino for restore. it has a solid body to work with, however I noticed ...
A: Prior to the late 80's auto companies used to weld the panels together on the assembly line and then ...
|
| 1971 dodge gas guage | 10/3/2008 |
Q: in previous e mail sent wrong address correct is: creekrats13@yahoo.com ...
A: If I was doing the job I would locate the fuel gage feed wire near the fuel tank. In this car there ...
|
| gas guage 1971 Dodge does not work | 10/3/2008 |
Q: gas guage stopped working while car was stored and seldom started tank was near full with original ...
A: If I was doing the job I would locate the fuel gage feed wire near the fuel tank. In this car there ...
|
| System not charging | 10/2/2008 |
Q: 67 Dodge Coronet not charging, I have replaced alternator, regulator, battery is new. I have also ...
A: OK, lets go step by step. With the engine idling remove the green lead (small wire) from the ...
|
| 1967 Firebird No Spark at Coil | 10/2/2008 |
Q: I've got a 1967 firebird with the original 400. I can not get any spark at the coil. I held it 1/2 ...
A: If the points do not close when the cam is on the low point there will be no spark. You could have ...
|
| System not charging | 10/2/2008 |
Q: 67 Dodge Coronet not charging, I have replaced alternator, regulator, battery is new. I have also ...
A: Bart, I think that you have just given me the magic clue, the shorted wire. Pull the alternator off ...
|
| 1952 Cadillac 626-6 Volt Polarity | 10/1/2008 |
Q: Greetings, My car make is as follows; 1952 Cadillac 626 V8 313 (I believe) We rebuilt it. 6 Volt ...
A: Now this is only my opinion so do not rate me as a moron for my answer. If it was my car I would do ...
|
| 1970 Corvette | 10/1/2008 |
Q: just lately I can drive some where with it,when I stop and turn it off,It may or may not start.I ...
A: It sound like it could be the solenoid on the starter, a common problem. But to be sure check all of ...
|
| Carbureter Idle Jet Adjustment | 9/30/2008 |
Q: Sir: I have a 74 Dodge Pickup with a 318 2V, auto trans, 126,000 miles. I continue to have a ...
A: Your vintage truck is part of the reason that the industry went headlong feet first into the fuel ...
|
| System not charging | 9/29/2008 |
Q: 67 Dodge Coronet not charging, I have replaced alternator, regulator, battery is new. I have also ...
A: The first thing to check is the grounding between the body and the engine. The alternator is ...
|
| 1952 Cadillac 626-6 Volt Polarity | 9/29/2008 |
Q: Greetings, My car make is as follows; 1952 Cadillac 626 V8 313 (I believe) We rebuilt it. 6 Volt ...
A: If you reverse the battery leads on the car the alternator will direct short circuit through the ...
|
| Packard 120 vibration damper | 9/29/2008 |
Q: I have a 1938 Packard 120 (282cu in) and was wanting to know how can you tell when the crankshaft ...
A: The only test that I know of a visual test once the damper is off the car. Make sure that the rubber ...
|
| 1977 chevy camaro hot air | 9/29/2008 |
Q: i have a 1977 chevy camaro LT with a 305 engine. the problem i have is that while driving I feel ...
A: I would check the rubber seals at the base of the steering column and the wiring grommets on the ...
|
| 1969 ford ranchero | 9/29/2008 |
Q: what could make cyclenders 5, and 6 on an inline 6 300 engine not fire i cheaked the compression an ...
A: The first thing that I would do is to take a compression test. It is possible that the head gasket ...
|
| Powerglide no drive or reverse | 9/27/2008 |
Q: The transmission was operating satisfactorily and was removed to replace the shifter shaft seal and ...
A: I am afraid that it sounds like the torque converter slipped when installing the transmission. This ...
|
| 1958 Ford Fairlane 500 V8 automatic 352 CID | 9/27/2008 |
Q: The problem is over-heating at idling or at low speed (as in a parade) Never over-heats from 30-80 ...
A: A clutch fan is a device that goes in between the fan itself and the water pump pulley. It is a ...
|
| 1947 International KB-2 | 9/27/2008 |
Q: hey I have a pick up Mentioned in subject that just wont start what may the problem be? without the ...
A: Ok, a spark ignition engine needs electricity to run the ignition system. You will need to start at ...
|
| 1967 Thunderbird | 9/26/2008 |
Q: My starter makes a loud grinding sound on occassion when I start the car. I assume I need a new ...
A: The problem is probably the starter drive. It might be grinding on the edge of the flywheel gear ...
|
| Car books | 9/25/2008 |
Q: I have a first edition of Last Chance Garage, with coffee spilled on it during the 1984 One Lap of ...
A: Actualy it is the coffee stain that is worth the money as the books can be found on E Bay and in ...
|
| Generator Idiot Light | 9/24/2008 |
Q: I have a 1969 Chevy el Camino with the generator idiot light illuminating. I have replaced the ...
A: There a a diode in the alternator that controls this light and the charge rate for the alternator. ...
|
| VOLTAGE CONVERSION | 9/24/2008 |
Q: .
A: Jason what that means is that you will have to install a new alternator in place of the generator. ...
|
| rings or valves | 9/24/2008 |
Q: Brad, My 55 Chevy, 235ci 6 cyl, powerglide is starting to smoke a little blue smoke. Mostly at a ...
A: At this point without a compression test my guess is that it is mostly Valve guides and or seals. ...
|
| Operation of headlamps 1963 T-Bird | 9/24/2008 |
Q: We have a 1963 Ford Thunderbird and would like to know how the high beam and low beam headlamps are ...
A: Each of the two outer headlamps have two filaments. The inner bulbs only have one. When the low beam ...
|
| Electrical ground | 9/24/2008 |
Q: 99 Chev Blazer. Battery runs down overnight. Something causes large spark when terminals are ...
A: The test light does not work on a vehicle with a computer as a test for drain. The computer stays ...
|
| hard starting when hot | 9/21/2008 |
Q: I have a 1952 Chrysler Windsor. When the vehichle has been run and I shut it off for a few ...
A: I have a hunch that the problem is in the carburetor. Take off the air cleaner and run the engine ...
|
| ignition system | 9/20/2008 |
Q: hey?i recently bought a 1959 edsel, i have replaced the solenoid, the coil,spark plug wires,coil ...
A: You appear to have an open in the ignition wire coming from the ignition switch to the coil. There ...
|
| 1939 Plymouth p8 turn signals | 9/20/2008 |
Q: I have an after market turn signal system for this car which does not work right. You have to turn ...
A: Most flashers are heat sensitive devices. That is the more current that passes through them the ...
|
| A/C Compressor | 9/18/2008 |
Q: I have an original 1967 Impala SS with the Comfortron auto temp. system. The A/C compressor will not ...
A: If the system is calling for heat or warm the fan will not come on until the engine temp is up to ...
|
| A/C Compressor | 9/18/2008 |
Q: I have an original 1967 Impala SS with the Comfortron auto temp. system. The A/C compressor will not ...
A: In many of those automatic systems the compressor stayed on as long as the outside temperature was ...
|
| miss fire | 9/16/2008 |
Q: I have an all original 1929 Graham Paige. Car runs great but when you turn on the headlights and ...
A: I would check the charging voltage with the lights on and the engine at road speed. If the voltage ...
|
| 1923 studebaker | 9/15/2008 |
Q: I have a 1923 studebaker I am restoring, and I need to know, was it a 6 or 12 volt system. Also how ...
A: With your permission lets treat each question as a bit of a learning process. Now, is there a ...
|
| 1923 studebaker | 9/15/2008 |
Q: I have a 1923 studebaker I am restoring, and I need to know, was it a 6 or 12 volt system. Also how ...
A: Lets do the questions in order. The lest you have given me is too long to answer on this form in one ...
|
| 1986 chrysler new yorker tubo 4 cyl | 9/14/2008 |
Q: my car has no power. i have replaced the map sensor,brain,plugs,etc. it will run when its in park ...
A: It sounds very much like a plugged catalytic converter. A simple test is to remove the oxygen ...
|
| 55 chev 265 | 9/13/2008 |
Q: the engine has not been started since 1993. Stored inside garage. What are the first things I need ...
A: Ok, I have a procedure for starting an old car: 1. Remove the spark plugs and ad a couple of table ...
|
| 1963 Ford drops out of gear | 9/12/2008 |
Q: My 1963 Galaxie XL 500, 352 engine, automatic on column, drops from Park to Reverse without warning ...
A: This was a common problem with that era Fords. Ford fixed the problem with an insert for the owners ...
|
| 1950 willy's jeepster | 9/11/2008 |
Q: I hope you can help, I have a customer with a 1950 willy's jeepster and we installed an aftermarket ...
A: What are you running for a charging system? A generator and a regulator? Remember that 6 volt ...
|
| Powerglide Transmission | 9/10/2008 |
Q: I have a 55 chev,,,265,,,powerglide I tried to fill my rebuilt transmission with fluid and the fluid ...
A: The fill procedure for this transmission is to put in three quarts and then start the engine. Then ...
|
| 1966 cadillac | 9/6/2008 |
Q: All works great except the headlights. I have the book but cannot figure out how to change the ...
A: If the fuse is on the headlight switch, it is better to remove the switch from the dash to get at ...
|
| Low beams won't work - high beams will | 9/6/2008 |
Q: My son has a 1978 Mercury Marquis, the high beams work and the low beams will come on with the high ...
A: The headlights in question, the outer two, are double filament bulbs and there is a good chance that ...
|
| 1951 Pontiac Radiator question | 9/6/2008 |
Q: We are looking to buy a radiator for our 1951 Pontiac Chieftain with a Straight 8. I have sent out ...
A: I have been been fortunate in that our local radiator guy is a fellow street rodder and he will ...
|
| steering wheel change | 9/6/2008 |
Q: I have a 1946 international which has been mounted onto an s10 chev chassis. So the steering wheel ...
A: The last one that I did like this I bought an adapter from one of the companies that sells after ...
|
| rear brake drum 1954 dodge coronet | 9/5/2008 |
Q: I can't seem to be able to remove the rear drums as I want to do a brake job on it. the fronts came ...
A: Short of using a torch to cut the drums off the car a wheel puller is the way to go. I have had to ...
|
| 68 Buick 350 Not running smooth above idle. | 9/4/2008 |
Q: I just completed a stock rebuild of my 68 Skylark's 350 engine. It starts and idles just fine and ...
A: Ok, that tells me that the vacuum advance is working and that the breaker plate in the distributor ...
|
| 1974 Beetle .... no spark | 9/3/2008 |
Q: First off, I have tried around locally, no one can come to see the car for at least a week I have ...
A: Well lets see if we can sort this puppy out and make it growl. Now, take your test light and connect ...
|
| 68 Buick 350 Not running smooth above idle. | 9/3/2008 |
Q: I just completed a stock rebuild of my 68 Skylark's 350 engine. It starts and idles just fine and ...
A: The coil voltages sound fine. I still lean towards the distributor for some reason. Try an ...
|
| 64 Impala SS Steering | 9/2/2008 |
Q: I just replaced the power steering control valve in my car. The car now pulls left. coincidence, or ...
A: There is an adjustment nut on the end of the control valve. With the car on a lift or jacked up on ...
|
| firing order sequence | 8/27/2008 |
Q:
A: I would check several sources for manuals. there are always Motor's Auto Repair Manuals listed for ...
|
| R 10 ovrdrive | 8/25/2008 |
Q: I was driving my '58 Rambler after a major overhaul. Everything was working very well. All of a ...
A: If the planetary gear set seized up because of lack of lubrication, you are faced with removing and ...
|
| 1926 Buick 4DR Sedan | 8/24/2008 |
Q: hope you can help me. I recently acquired this 1926 Buick which doesn't run. The Distributor has ...
A: Six cylinder GM cars use 1-5-3-6-2-4 and you will need to find number one by bumping the engine over ...
|
| block casting numbers | 8/24/2008 |
Q: I have a 1980 camaro z28. I'm trying to figure out if the engine is original. I found a casting ...
A: This engine was origionaly in a 1977 Vette or a B body GM car. If in the Vette it was rated at 165 ...
|
| 1965 Corvair 180 hp turbo , hesitation | 8/23/2008 |
Q: I am getting this car going after a period of storage. The fuel system was cleaned out a few years ...
A: I have a wall full of trophies won when driving a like car in SCCA compatition. Now your problem ...
|
| color code for 71 lime green chevy truck | 8/23/2008 |
Q: I am beginning to restore a 71 Chevy Longhorn PU truck. The color scheme is white/lime ...
A: There should be a trim tag located on the firewall. On the right hand side of the second line is ...
|
| trouble starting hot/warm engine | 8/21/2008 |
Q: I have a problem starting my 67 beaumont when it has run for a few minutes. If I jump the starter ...
A: It is time to start checking with a voltmeter and find out where the voltage stops when the system ...
|
| 64 Impala | 8/21/2008 |
Q: i am 16 and my uncle is giving me this car. its a 64 impala 4 door. its been sitting in a barn for ...
A: Kyle: I spent mst f my 50 years in teaching in a high school auto shop. Pardon an old man's long ...
|
| 1968 Mercury Cougar, Gasoline mixing into oil | 8/19/2008 |
Q: I believe the gasoline is mixing into the oil, what could be the problem here?
A: If the engine is not hitting on all cylinders because of plugs, wires, or low compression fuel can ...
|
| '50 216 Rocker Assembly | 8/19/2008 |
Q: Brad, I have chattering rockers. The shaft(s) seem to be worn. I have purchased a new set. Is ...
A: It is straight forward. Watch and lay the parts out in order as you take it apart and then reverse ...
|
| mustang running hot and heater does not work | 8/18/2008 |
Q: I have a 1966 200cid automatic mustang that seems to run around 190-215. I replaced the thermostat ...
A: It sounds like two problems. The heater could be a plugged core. The fix is to replace the core. If ...
|
| No start 1969 chevrolet 350 engine | 8/15/2008 |
Q: I have a rebuilt 1969 350 engine with holley 600cfm, HEI inginition. I put new spark plugs and ...
A: OK, did you pre oil the lifters before adjusting them? If not it is possable that you have the ...
|
| 1961 Ford Econoline truck/170 6 cyl. | 8/14/2008 |
Q: Mr. Sears.....could you tell me what the gear ratio was in this truck originally? I want to change ...
A: My answer is based on experience. Changing the ring and pinion to a lower the gear ration will make ...
|
| Trnsmission | 8/12/2008 |
Q: I have a 1966 Chev pickup with 283 and a powerglide that was missing downshift linkeage. I have all ...
A: It is adjusted in the full throttle position so that when the accelerator is on the floor the ...
|
| my 1972 bug cuts out | 8/12/2008 |
Q: up recently had new regulator box, oil change the idle turned up thank you for your time craig.
A: I would make sure that the spark plugs are properly gapped. A large gap will cause the required ...
|
| 1954 Pontiac | 8/9/2008 |
Q: How can I tell if I have stuck rings in my 1954 pontiac straight 8? I finally got her running and ...
A: The blow by and the fact that hot start is a problem tell me that the rings are probably well past ...
|
| 1966 Mustang radiator | 8/9/2008 |
Q: Amazing! My son and I are having the exact same problem as one you addressed on July 5, 2008, ...
A: It kinda sounds like the radiators that you have been buying are more universal one sized fits all ...
|
| 1956 chevy headlight switch | 8/8/2008 |
Q: I recently have been having trouble with my interior gauge lights and since the headlight switch is ...
A: Well short of selling the car or getting some one else to stick their paw up under the dash, your ...
|
| cable for the wipers on a 1956 chevy | 8/8/2008 |
Q: how do you run and connect the cables for the wipers on a 1956 chevy
A: Ok, lets give it a whirl. With the wiper motor installed start the engine and turn on the wipers. ...
|
| Overdrive tranny | 8/8/2008 |
Q: I have a 56 ford with a three speed overdrive. It keeps popping out of second gear. The local shop ...
A: Yes the case will bolt up with no problem but you still have to dissassemble both transmission as ...
|
| 69 MUSTANG FUEL GAUGE | 8/7/2008 |
Q: i saw your reply to the 66 mustang. i should unplug the sending unit and ground the wire that plugs ...
A: It sound like the problem, based on the smack the dash method of diagnosis, is in the dash. Key on ...
|
| 1961 Ford Econoline truck/170 6 cyl. | 8/5/2008 |
Q: Mr. Sears...I would like to know what the points gap would be on the 170 in the Econoline I have, ...
A: The spark plugs are Champion F14-Y set at .034". The points are set at .025" and the timing is 4 ...
|
| 1976 CJ-5 man, no extra equipment | 8/5/2008 |
Q: This has a six banger, I have done everything to make it run smooth. new carb, electric fuel pump, ...
A: Well I hate to tell you this but you missed the first step that any old time tune up man is a shop ...
|
| 1966 Mustang radiator | 8/4/2008 |
Q: Amazing! My son and I are having the exact same problem as one you addressed on July 5, 2008, ...
A: It is not the only cure, but mine for the following reasons: 1. I am a thrifty New Englander ...
|
| differential question | 8/4/2008 |
Q: i have a 67galaxie the differential has 10 bolt cover the ring gear measures 8.5" it has 28 spline ...
A: The first place would be doing the Junk Yard crawl. When I was younger several buddies and I would ...
|
| tining | 8/3/2008 |
Q: Brad, I have a 66 chevy, 327, 350 hp engine, I believe I have a timing or electrical issue. I ...
A: This is right about the change over in the carburetor from the idle circuit to the high speed ...
|
| differential question | 8/3/2008 |
Q: i have a 67galaxie the differential has 10 bolt cover the ring gear measures 8.5" it has 28 spline ...
A: What you appear to have is a Ford built 10 bolt (called as such because of the 10 bolts holding the ...
|
| fuel pumps | 8/2/2008 |
Q: does a 1977 f100 have a pump in the tank .I know its got one on the block but i was wondering if it ...
A: If it has a mechanical pump on the block there should not be a pump in the tank. There is a nylon or ...
|
| 84 chevt p/u master cylinder | 8/2/2008 |
Q: got an 84 chevrolet p/u.went to part store to buy a master cylinder .they told me they needed a code ...
A: There should be a decal on the inside of the glove box door that is a Service parts ID sticker. The ...
|
| Leaking Pinion Seal | 8/2/2008 |
Q: Brad, In a previous question you advised me on getting the overdrive working on my '49 Packard. ...
A: welcome back. There are several things that I would look for. First would be a ring worn around the ...
|
| 1994 chevy g20 conversion van | 8/1/2008 |
Q: my left horn button just stopped working, the right button works perfectly any help would be greatly ...
A: It is apparent that the left button has lost it's contact or that one of the small wires just under ...
|
| 1949 chevy solenoid repair/replace/cross reference | 8/1/2008 |
Q: I am working on my 1949 Chevy Styline Deluxe w/ a 216 engine and I am having trouble trying to get ...
A: Stoney, I hate to be the bearer of sad tidings but from what you said I don't think that the problem ...
|
| 1979 corvette brake rotors | 8/1/2008 |
Q: Do I need a drill press to remove the old rivets from a front brake rotor I need to replce or can I ...
A: Have you bought just the rotor for your car? Some of these the rotor is only available as a hub and ...
|
| charging system | 8/1/2008 |
Q: i have changed my voltage reg 3 times and had the generator rebuilt 2 months ago. had the ...
A: Does the system quit charging completely or just the amps fall off a bit? Check the system by ...
|
| '59 Ford Failane 500 Galaxie | 8/1/2008 |
Q: I found a '59 Ford Fairlane 500 Galaxie that I'm interested in buying. I test drove it and it has ...
A: Back in the day most Fords came from the factory without power brakes and steering. We mechanics in ...
|
| 1947 flat head ford firering order v8 | 7/31/2008 |
Q: i have a 1947 ford coup i can not find the firering order it is a flathead v8 engine .i think it is ...
A: Ford flat head engines used 1-5-4-8-6-3-7-2 as a firing order. Number one cylinder is the first one ...
|
| 6 volt vs 12 volt | 7/30/2008 |
Q: I own a 1938 Pontiac Sport Coupe 6 cylinder. What are the dangers of using a 12 volt battery to ...
A: There was a company around a dozen or so years ago that manufactured a battery system like you ...
|
| electrical ground issue | 7/30/2008 |
Q: I have a 1966 Ford Mustang that I am told has a ground problem. One day while leaving a cruise night ...
A: It sound like a gadget on the back of the instrument cluster called the constant voltage regulator ...
|
| 1939 Ford Tudor window regulators | 7/28/2008 |
Q: Brad, I was wondering if you knew where to purchase new window regulators and channels for a 1939 ...
A: Grab a copy of Hemmings Motor News. It is the old car hobbies classified bible. There are a number ...
|
| rear wheel lugs | 7/26/2008 |
Q: Have attempted to remove nut on rear wheels of my 64 Rambler to access brakes but cannot budge ...
A: They should be right handed but look at the end of the stud. If they are left handed there should be ...
|
| 1947 flat head ford firering order | 7/26/2008 |
Q: i have a 1947 ford coup. i think it is a 289 flat head v8 engine does anyone no the firering order?
A: Seeing as you do not know the year or size of the engine, this is a difficult one. But we can solve ...
|
| engine vibration | 7/25/2008 |
Q: I recently purchased a 1950 Bel-Air with the 235 C.I.and powerglide transmission. the engine idles ...
A: Now comes the Sherlock Holmes 007 work. Is it a vibration or the engine missing? You can check that ...
|
| rough idle | 7/24/2008 |
Q: I have a 57 Ford with two four's shich have both been rebuilt The car idles rough not real bad but ...
A: From what you say it sound like the timing chain has jumped a tooth. The easiest check for a sloppy ...
|
| engine vibration | 7/22/2008 |
Q: I recently purchased a 1950 Bel-Air with the 235 C.I.and powerglide transmission. the engine idles ...
A: That strange looking part is the head of the bolt that holds the balancer on. It looks strange ...
|
| Head light switch | 7/22/2008 |
Q: On a 69' Chevy C10 Pick up truck- Trying to replace the headlight switch next to the instrument ...
A: On the back side of the headlight switch, opposite the wires, there should be a small spring loaded ...
|
| 1966 Mustang Fuel Gauge | 7/22/2008 |
Q: The fuel guage on my mustang does not work, it is normally at empty(left) but when I turn the key it ...
A: If you can get at the wire to the sending unit, remove it and ground it. Then turn on the key. If ...
|
| spark plug wire diagram, firing order? | 7/21/2008 |
Q: Im wondering if you know of a place I could get a DVD or photo with an explanation as to the firing ...
A: OK standing by the right front fender (passengers side) looking in the clips that hold the cap onto ...
|
| 1953 Kaiser Manhatten | 7/20/2008 |
Q: I am replacing the rings in the pistons. What order doe the rings go. There are four slots.
A: Did you not get an instruction package with the rings when you bought them? The compression rings ...
|
| Spark plug order on distributer | 7/19/2008 |
Q: I have a 1960 Chev 235 6 cylinder. Rebuilt 2 months ago. I just put in new points. I started it, and ...
A: The firing order is 1-5-3-6-2-4. The trick will be to find which hole is number one. Do do that ...
|
| headlights blink | 7/18/2008 |
Q: I have a 56 Chevy 4 door wagon with a small block chevy engine. The front wiring harness is recent ...
A: Have you upgraded the headlight like changing them to halogen bulbs? Check the lenses and see what ...
|
| 76 VW Beetle Vacuum Schematic | 7/17/2008 |
Q: looking to make sure my vacuum advance and hoses are correct. 76 Beetle fuel injection. Do you ...
A: I would check with www.books4cars.com. If they do not have what you are looking for latch on to a ...
|
| air cleaner | 7/16/2008 |
Q: i have a 1968 plymouth valiant with the 225 slant six. it has the original air intake drawing its ...
A: That line that runs to the valve cover from the air filter is part of the emissions system. When the ...
|
| 66 Mustang engine troubles | 7/15/2008 |
Q: I have a 66 Mustang that was given to me ( I know! Awesome gift!) Anyway, I havent had any trouble ...
A: It sounds like it could one of several problems. One, the carburetor could have some dirt in the ...
|
| Do i have a reverse ground 34? | 7/15/2008 |
Q: I have a 34 ford fully restored 4-door sedan. It has a 6volt system and a Flathead V8. In the past ...
A: That would be a fist step. If the problem comes back then pull the tank and use a sloshing compound ...
|
| 68 4v 289 Mustang | 7/14/2008 |
Q: My Mustang starts fine when the engine is cold, but if I turn the car off once the engine is fully ...
A: Two things come to mind here. First there could be wear on the inside of the starter. The bushings ...
|
| 1969 Bonneville trunk letters removed | 7/14/2008 |
Q: I just bought a 1969 Pontiac Bonneville that had the trunk letters removed and filled in. Where can ...
A: Ernie, the trick that has always worked for me was to check the back side of the panel that had the ...
|
| 1939 chevrolet 216 engine(rear seal anmd front seal) | 7/14/2008 |
Q: Need to replace the front timing cover seal. Does the balancer just come off with a puller. Is there ...
A: If the engine is stock the bolt that holds the front pulley in place is the part that you would put ...
|
| 1960 Jaguar XK150 DHC | 7/14/2008 |
Q: Long story made short. Took my car in June 2001 to a man that found out about my car and wanted to ...
A: I hate these stories. There are a few bad garages out there that operate like this and cast a shadow ...
|
| 64 t'bird convertible | 7/14/2008 |
Q: when i eccellerate from a standing start my 64 t'bird appears to be in second gear!if i select first ...
A: There is a one way clutch inside the transmission that engages low gear when the shift lever is in ...
|
| Oil Pressure Relief Valve | 7/12/2008 |
Q: Brad, I have a 1939 Dodge D11 4dr that I am restoring. The car sat for 20 years in storage so I ...
A: Good, it moves. I know it is a pain but put the cap back on, start the engine, then shut it down and ...
|
| 73 Dodge Charger | 7/11/2008 |
Q: I have a 73 Dodge Charger with 40k original miles that has been sitting in my garage hopefully ...
A: It used to be that radiator shops would boil out your gas tank for you. But I do not know of any now ...
|
| Oil Pressure Relief Valve | 7/11/2008 |
Q: Brad, I have a 1939 Dodge D11 4dr that I am restoring. The car sat for 20 years in storage so I ...
A: You assumption that the pressure relief valve is stuck appears to be correct. When the valve is in ...
|
| valve guide lubrication | 7/10/2008 |
Q: Brad: Thanks for being a resource. I'm rebuilding a 1915 Buick 4 cylinder engine. It has the ...
A: The clearance numbers that you quote sounds about right. But steel on steel might be a problem. cast ...
|
| Overdrive followup | 7/10/2008 |
Q: Brad, thanks for your help previously. I have replaced my overdrive relay with a *modern* ...
A: Sound to me as if it is time to pull the solenoid out of the car. It sound like the end of the ...
|
| 1939 engine in a 29 Model A | 7/9/2008 |
Q: I have a 1939 Ford FlatHead V8 engine and transmission that I would like to put in a 1929 Model A 2 ...
A: It should fit under the hood but some welding and fabrication for motor mounts and such will need to ...
|
| 3 spd manual with o.d. | 7/9/2008 |
Q: I have a 57 Chevy with a 3 spd manual w/ overdrive. When the car is stopped and the O.D. "T" handle ...
A: In the over drive unit there is a free wheeling device. It is a sprag or one way clutch device very ...
|
| valve guide lubrication | 7/8/2008 |
Q: Brad: Thanks for being a resource. I'm rebuilding a 1915 Buick 4 cylinder engine. It has the ...
A: Wow did this one send back into the dark ages. Well, if memory serves me correct the valve guides ...
|
| 1930s Transmissions | 7/8/2008 |
Q: Howdy Brad. Can you tell me what the "typical" (most common) transmission would have been during the ...
A: By the thirties the industry had pretty much settled on the three speed manual transmission with the ...
|
| 64 t'bird convertable | 7/7/2008 |
Q: I need to replace exhaust manifold gaskets on my 64 t'bird.Very limited space within engine ...
A: The last one of these that I did I pulled the cylinder heads off the engine, did the manifolds on ...
|
| 1950 Chevy 216 bent push rods and broken rockers | 7/6/2008 |
Q: I have a chevy 216 with bent push rods 4 bent pushrods and 2 broken rocker arms. The fleetline had ...
A: Gregg, I would have the cylinder head off this beast in a heart beat. I would want to check contact ...
|
| 1966 Mustang radiator | 7/5/2008 |
Q: I purchased a radiator for my 1966 Mustang and it does not fit. There is not enough clearance ...
A: I have a question for you and then we can get down to business. Is there an aluminum spacer between ...
|
| Packard overdrive | 7/4/2008 |
Q: I have a 1949 22nd series. It has overdrive, but the overdrive has not worked since I got the car ...
A: Put a switch in that jumper line under the dash. You don't want the solenoid to energize until you ...
|
| Packard overdrive | 7/4/2008 |
Q: I have a 1949 22nd series. It has overdrive, but the overdrive has not worked since I got the car ...
A: That wire on the left side should be a smaller wire and run down to the governor on the overdrive ...
|
| Packard overdrive | 7/4/2008 |
Q: I have a 1949 22nd series. It has overdrive, but the overdrive has not worked since I got the car ...
A: OK, here goes, the dash indicator light not working tells me that the circuit from the ignition ...
|
| wiring | 7/4/2008 |
Q: Sir, I have a 1966 mustang i would like to know how to re-wire the heater ,radio,dome and ...
A: The best that I can do for you is to point you to the following web site. It is a wiring diagram for ...
|
| set timeing on 390-1969 amc | 6/23/2008 |
Q: i checked it says to set it at TDC is this true, i have owned other amc's that were set at 5-BTDC. ...
A: TDC is correct. In 1968 new emissions standards were put into effect. The only way the makers could ...
|
| kit car build | 6/23/2008 |
Q: A few years ago I watched your PBS TV video series where you built a 2 seat sports kit car. Is ...
A: Unfortunately the copies of that year show have been lost. That car was a Cobra with a big block ...
|
| engine timming marks | 6/22/2008 |
Q: i have a 1976 Nova straight six motor, timming is gear driven with no timming marks, i know to bring ...
A: Every timing gear, the one on the cam and the one on the crank, for Chevrolet that I have ever seen ...
|
| 1989 camaro rs convertible | 6/19/2008 |
Q: I have this camaro convertible since 1994 and it needs alot of work,i was told to fix it and hang on ...
A: A car is considered an antique when it reach 25 years old. The Classic designation is used on ...
|
| Rear axle seal leaking | 6/19/2008 |
Q: Brad, I have a 72 Dodge Demon 340. I bought it new and therefore I know that it has not been ...
A: Ok, here is the way to tell the difference. The 7 1/4 is used on 69 and 70 six cylinder cars and has ...
|
| Removing a harmonic balancer | 6/17/2008 |
Q: I need to get the timing cover off of a chevy 235, but the harmonic balancer is in the way. Usually ...
A: If it is what I am thinking of from your description, it is the crank adaptor that is threaded into ...
|
| beetle starter | 6/16/2008 |
Q: Unmodified 69 beetle, intermittently won't start, with only a brief click. Randomly occurs, then ...
A: In cases like this when the car acts up I turn on the lights. Then try the starter again. If it only ...
|
| incorrect mileage on dupicate title | 6/12/2008 |
Q: I inherited a 1959 Cadillac Sedan Deville from my father. The car has always been garage kept and ...
A: There are several ways that I would approach this problem. First I would visit the title department ...
|
| St300 transmission | 6/12/2008 |
Q: Brad: I have a Super Turbine 300 2 speed automatic in my 1950 Willys, with a Spicer transfer case ...
A: There is supposed to be a gasket between the modulator and the transmission case and if it missing ...
|
| 67 camaro will not turn over | 6/11/2008 |
Q: Howdy I have a 67 rs ss. I am having a serious problem with her. She will not start without a boost ...
A: It sounds like the battery is not being charged by the alternator/generator. If you have a voltmeter ...
|
| 1979 Corvette | 6/10/2008 |
Q: I have a 1979 Corvette, and the header keeps burning through spark plug wires. Do you have any ...
A: If the engine is stock and has the stock headers then the factory equipped spark plug wires with the ...
|
| Brake problem | 6/6/2008 |
Q: I am interested in buying a 1969 corvette; 350. The brakes do not work and want to know thru ...
A: The first step is to check the master cylinder for fluid. If it is empty it indicates a leak some ...
|
| Brake lights 1966 Corvette | 6/4/2008 |
Q: I have a 1966 Corvette. Recently the brake lights work one day then don't work the next, sometimes ...
A: The stop light switch sends a single wire voltage up to the directional switch. With the switch in ...
|
| Replace Transmission seal | 6/2/2008 |
Q: I have a 1966 Mustang with a 6 cylinder, 3-speed manual transmission. I have a fluid leak out the ...
A: The rear seal can be replaced by removing the driveshaft. Disconnect the rear universal joint from ...
|
| IH carb/governor | 6/2/2008 |
Q: Not sure where to post, but I think this is as close as I can get. I have a 1952 IH/Farmall ...
A: That should not keep the engine from starting. Last year in the middle of a show field my Ford 8-N ...
|
| 1972 GMC Pickup Resistance Wire Smoking Hot | 6/2/2008 |
Q: I have a friend that had the engine rebuilt in his 1972 GMC Pickup and between the two of us we have ...
A: Ok, lets go a step at a time. 1. Turn on the key and see if the wire gets hot. If it does remove ...
|
| 1972 GMC Pickup Resistance Wire Smoking Hot | 6/1/2008 |
Q: I have a friend that had the engine rebuilt in his 1972 GMC Pickup and between the two of us we have ...
A: If the resistance wire is getting smoking hot it is because there is too much current passing ...
|
| 54 Pontiac Chieftain | 6/1/2008 |
Q: I'm working on a 54 Chieftain that had the wiring under the dash cut. I've gotten most of it figured ...
A: Ok, you ready to follow this? If the car has directionals there are two separate wires that run back ...
|
| Plymouth Duster Starter Relay Bypass | 6/1/2008 |
Q: I have a 73' Duster 340 V8. Auto. I am and have been having problems with the fender mounted starter ...
A: Before making changes in the wiring I would check the connector where the wiring harness goes ...
|
| 61 Thunderbird Fuel Sender Replacement | 5/31/2008 |
Q: Brad, I want to replace the fuel sender unit in my 61 Thunderbird and can't tell by the service ...
A: Now don't shoot me if I am wrong but if I remember right when Budd started building the T bird body ...
|
| 1937 Ford | 5/31/2008 |
Q: 37 ford flathead 8 with vacuum break distributor, no spark to plugs. Distributor has two caps, one ...
A: To test the coil, remove it. It is attached to the top of the distributor cap with several screws ...
|
| How to remove old gas from tank? | 5/30/2008 |
Q: I have a car stored that I start every month or two. The problem is, the last time I added gas to ...
A: If it was me I would make a trip to the auto store and get some Stabil. It is an additive for gas to ...
|
| rear main seal leak/replacement | 5/28/2008 |
Q: I have an '86 Olds Cutlass Supreme I am restoring. It has the 5.0L 307 V8 with severe oil leaks. ...
A: If the engine has a two piece rope seal then it can be changed by removing the oil pan. If the car ...
|
| 1961 Chevy c10 truck | 5/27/2008 |
Q: We are trying to replace a started on a 1961 Chevy c10 truck. We can see only 2 bolts but we have ...
A: There are two bolts at the bell housing. The third bolt is at the other end of the starter and it is ...
|
| transmission decoder | 5/27/2008 |
Q: I have a 68 mustang with an unknown transmission. I found these numbers on the transmission. Ford ...
A: The best that I can do with a part number instead of information of the transmission tag is that it ...
|
| 39 LaSalle Running Hot | 5/26/2008 |
Q: My 39 LaSalle 5019 is running hot, the hoses have not collapsed, the dwell is where it should be at ...
A: The first thing that I would do is to reset the timing. If you have the timing at 5 degrees retarded ...
|
| 1941 Pontiac Coupe "screeching" | 5/26/2008 |
Q: Had my '41 Pontiac Flattie 6, with 3 on the tree in a Holiday Parade. After clutching a thousand ...
A: Are you sure that you are not getting plain old fan belt screech? At parade speeds and a 6 volt DC ...
|
| 1954 Chevy Bel Air transmission slip | 5/24/2008 |
Q: "My father left me his '54 Chevy Bel Air with Powerglide transmission. I live in the mountains of ...
A: The Powerglide transmission does have slippage when climbing hills and such. The torque converter ...
|
| Get a title that was registered in S.C. | 5/24/2008 |
Q: The 1967 firebird was registered in S.C. but hasn't been licensed in over 20 years. Now, S.C. ...
A: Each state has provisions for cases like yours I would call the department of motor vehicles for ...
|
| 1968 Chevrolet P/U front drum brakes | 5/23/2008 |
Q: I have a 1968 Chevrolet 1/2 ton pick up. I wanted to do the brakes, so I ordered front and rear ...
A: Cut the rivets and install the new drums. make sure that they fit the hub snugly as this is what ...
|
| collapsed radiator hose | 5/22/2008 |
Q: I have a 1953 Buick Special that I drove recently, parked it in the garage, and then the next day ...
A: Radiator caps are pressure/vacuum caps. When the engine heats and the coolant expands it will allow ...
|
| 65 Mustang | 5/21/2008 |
Q: My 65 mustang,289 engine recently started darting to the left and sometime the right when I drive. I ...
A: This a serious safety condition. You either have a tie rod end that is about to come apart or a ...
|
| 1972 monte carlo all numbers match no mods | 5/21/2008 |
Q: A have a 402 big block in this beast. but i have the org. card quad-jet. i need to know the best way ...
A: The first thing that you need to do in the order of diagnosing the problem is to take a compression ...
|
| Rear Seal 1949 Pontiac | 5/20/2008 |
Q: How big of a job is it to replace the rear seal in a 194 six in a 1949 Pontiac?
A: Removing the oil pan is a major pain in the you know where. The recommended procedure is to remove ...
|
| 1966 tbird 390 detonation | 5/19/2008 |
Q: i have a 66 tbird with a 390 motor,I just purchased it and while driving home i went up a hill and ...
A: The first thing that I would want to see from this car is a compression check numbers for each ...
|
| 1969 dodge rear axle leak | 5/19/2008 |
Q: how would i fix a leak in the rear axle of a 1969 dodge super bee i have changed the seals and ...
A: As the seal needs to be driven into the axle housing, it MUST be driven in square with a seal ...
|
| carb leak | 5/18/2008 |
Q: I asked a question back in March and you were quite helpful, thanks again. New issue, I rebuilt my ...
A: Good morning Bob: The temperature of ignition of gasoline is above 700 degrees F so fire is out ...
|
| carb leak | 5/18/2008 |
Q: I asked a question back in March and you were quite helpful, thanks again. New issue, I rebuilt my ...
A: Good morning Bob: Well the reality of the fact is that the Rochester single barrel carburetor of ...
|
| Stude rear end | 5/17/2008 |
Q: Have a 51 Stude 2R11 3/4ton pu with a heavy split axel. I want to rebuild the rear brakes. As I look ...
A: Hopeful there are two holes on that flange that have nothing in them but are threaded. If so once ...
|
| 1974 VW Beetle accelerator cable | 5/16/2008 |
Q: How do I replace this cable? The fitting snapped off of the end that is attached to the accelerator ...
A: The cable comes out from the front and is inserted through the tube from the front. I don't think ...
|
| 84 ford 3.8L head bolt tightening procedure | 5/14/2008 |
Q: I'm looking for the most current specification on tightening the head bolts on an 84 ford t-bird ...
A: Sorry for the delay but I was doing some digging to make sure that I had the latest and greatest ...
|
| 1968 lincoln 462 stopped turning over | 5/14/2008 |
Q: I have a 68 Linc. that has acouple of problems and its been sitting for sometime now. I have owned ...
A: You will need to check for spark and fuel. To check fuel remove the air cleaner and block open the ...
|
| fuse box | 5/14/2008 |
Q: where are the fuses for the turn signals on a 1957 ford failrlaine skyliner
A: There should be a fuse holder in the wire that runs from the flasher unit to the ignition switch. It ...
|
| 1968 lincoln 462 stopped turning over | 5/13/2008 |
Q: I have a 68 Linc. that has acouple of problems and its been sitting for sometime now. I have owned ...
A: I have a question for you. When you say that it does not turn over do you mean that the starter will ...
|
| 60 studebaker champ pu | 5/12/2008 |
Q: After engine overhaul and paint job my battery boiled over and ruined my paint job. Is regulator or ...
A: The most common cause is a faulty voltage regulator that overcharges the battery causing it to boil. ...
|
| 1965 Thunderbird Thermostat | 5/11/2008 |
Q: I have a 1965 thunderbird with a stock 390 300hp. What degree thermostat would you recommend ...
A: My recommendation would be for a 180/190 degree thermostat and a 50/50 mix of anti freeze. The anti ...
|
| 1969 firebird 350 lifters | 5/10/2008 |
Q: I have a 1969 firebird 350 convertible that has been in the restoration process for some time. it is ...
A: Ben, have you done a compression test on the engine? If not do one and then let me know and we will ...
|
| park lug wiring | 5/9/2008 |
Q: Can you please tell me the correct wiring order from each spark plug to each point on the ...
A: Ok, you have kind of answered a question. The problem is that we do not know if the distributor has ...
|
| 1950 Chevy P/U Hesitating and stalling | 5/9/2008 |
Q: Starts great, idles, runs fine for 5 or 6 miles then starts with a subtle hesitation, going quickly ...
A: Good, the fuel pump is located where it is supposed to be, below the level of the fuel at the tank. ...
|
| 1941 desoto master cylinder | 5/8/2008 |
Q: I am having a terrible time getting the master cylinder out of car. I beleive I have disconected ...
A: Boy, you are pushing the old gray matter to the limit. Look at the master cylinder where the shaft ...
|
| 1941 Plymouth | 5/8/2008 |
Q: How wide is a 1941 Plymouth Deluxe 4 door sedan? I have a trailor that has interior width of 6 ft 4 ...
A: Boy, that is going to be a tight fit with about 6 inches on either side. The tread width on that car ...
|
| 62 Tbird stalling | 5/7/2008 |
Q: I bought a 62 Tbird conv with the std 390 4 barrell setup. Car came from a dealer in St Louis with ...
A: There is a self cleaning fuel filter in the fuel tank. It is a sock type filter on the fuel pick up ...
|
| 84 ford 3.8L head bolt tightening procedure | 5/6/2008 |
Q: I'm looking for the most current specification on tightening the head bolts on an 84 ford t-bird ...
A: It is apparent that you have not seen the correct information. According to my reference material ...
|
| 1975 Chevy El Camino gas tank | 5/5/2008 |
Q: I am restoring this truck. This truck has been setting in a back yard for over 5 years. What is the ...
A: This is a problem that is made worse with what to do with the gas that comes out of it. If you have ...
|
| How to check for Spark/Fuel? | 5/5/2008 |
Q: I have a 1970 Dodge that in storage that I like to take out every few months. I've often heard that ...
A: To check for spark remove the coil wire from the distributor cap. Hold it about 1/4 inch from solid ...
|
| 1971 chevelle | 5/2/2008 |
Q: a mechanic told me the car has a rear main seal leak and oil pan gasket...how difficult is it to ...
A: It can be done in the car but it is a lot of work. Remove the front exhaust pipes, jack the engine ...
|
| 1990 CHEVY CAPRICE 305 | 5/2/2008 |
Q: MY SPARK PLUGS ARENT FIRING CHANGED THE ROTAR AND THE IGNITION MODULATOR AND STILL NOT FIRING I HAVE ...
A: It could be the pick up coil of the ignition coil. But a thought here. Remove the distributor cap ...
|
| a/c blower problems | 4/30/2008 |
Q: #1 my a/c blower works only on medium speed , will not work on low or high speed. #2 compressor ...
A: Question #2 is probably due to low refrigerant level in the system. The clutch should cycle to ...
|
| fuel pump??? | 4/27/2008 |
Q: I have replaced the plugs, wires, fuel filter, air filter, etc... But my 1966 250 IL6 still stutters ...
A: The list of "could be's" is a long one. Trash in the fuel tank plugging the inlet filter, bad ...
|
| chevy single barrel 235 carb | 4/26/2008 |
Q: i rebuilt the carb off my 1956 chevy 210 everything is stock. it was my first rebuilt attempt and it ...
A: The accelerator pump appears not to be working. With the engine off look down into the carburetor ...
|
| Wooden Spoke Wheels | 4/25/2008 |
Q: I Have a 1923 Studebaker with Wooden Spoke wheels Can you advise on how to look after and care for ...
A: Most wood wheels were varnished at the factory when the car was built. They used a marine grade Spar ...
|
| Jog my memory | 4/24/2008 |
Q: During the 1960s there was a pickup truck that was made to look like car. That is, it was built much ...
A: Chevrolet made the El Camino, and Ford had two different versions. One was on a Ford Falcon and the ...
|
| replacing ring gear in 1939 1/2 ton chevy | 4/24/2008 |
Q: While attempting to find someone who could assist me in replacing an old riveted differential ring ...
A: Well, a couple of things. According to my best sources the ring on the 1939 differential should be ...
|
| 1965 mustang 2b | 4/23/2008 |
Q: replacing the timing chains. what is the firing order,rmp,dwell,point setting and the prper way ti ...
A: The timing mark on the cam gear (big gear) should be at 6 O clock and the mark on the crank gear ...
|
| 56 Tbird Battery orientation | 4/22/2008 |
Q: I had assumed that the (+) pole of the battery faced the rear of the car, but the front cable is ...
A: 56 was the first year for the 12 volt battery and electrical system in the T Bird. All batteries 6 ...
|
| rough idle | 4/22/2008 |
Q: I own a 67 impala with a 396 engine, the short block is from a 1969 top of motor is original 67.It ...
A: That could very well be and this will turn out to be a 007 Sherlock Holmes check everything mystery, ...
|
| 64 Rambler 195.6 Firing Order | 4/21/2008 |
Q: I have a 1964 Rambler Classic w/ a 195.6 Inline 6 cyl. I need to know where the #1 cyl plug wire ...
A: The firing order is 153624. As to which hole in the cap that #1 goes in to be correct I would ...
|
| rough idle | 4/20/2008 |
Q: I own a 67 impala with a 396 engine, the short block is from a 1969 top of motor is original 67.It ...
A: I have some questions for you. What do you know about the history of the block? Is it stock? Does it ...
|
| Timing on a 1951 Chevy PU | 4/20/2008 |
Q: I have an old 1951 Chevy PU that someone replaced the 216 engine with a 235 engine. From the best I ...
A: An easy trip to remember about timing is that advance is always the opposite direction as rotation. ...
|
| Speedometer | 4/18/2008 |
Q: My speedometer and odometer,on 1973 Buick Rivera have quit working.Can this problem be a cable? ...
A: Ok, this is the way that I check out a speedometer and cables. I jack the rear wheels off the ground ...
|
| 1950 Plymouth | 4/17/2008 |
Q: I am trying to replenish the fluid in the "pumpkin" of my 1950 Plymouth Deluxe. However, when I went ...
A: Ok, we are pushing the limits of the old gray matter here so if I blow it don't call me a moron. The ...
|
| 1977 corvette radiator | 4/14/2008 |
Q: how difficult will it be to remove and install a new radiator in this car? it has air conditioning ...
A: First step is to disconnect the battery and then remove the transmission cooler lines. You will need ...
|
| Idle speed | 4/14/2008 |
Q: I have an 1987 f150 5.0 liter,it is idling high,around 900 rpm.How can this be adjusted on a truck ...
A: The major problems that we have seen with idle on these engines is usually dirt in the throttle ...
|
| 64 thunderbird carb | 4/13/2008 |
Q: I thought about what you said and removed the Holly carb and had the old one rebuilt. Its been ...
A: The other problem that you have is fire. Don't run the engine. I would haul the carburetor off and ...
|
| check engine light | 4/13/2008 |
Q: BRAD, i have a 1988 560sl mercedes. when im crusing around town my check engine light comes on, then ...
A: Is this a yellow or red light? If it is red it could be that you are showing low oil pressure at low ...
|
| 64 thunderbird carb | 4/13/2008 |
Q: I thought about what you said and removed the Holly carb and had the old one rebuilt. Its been ...
A: It sounds like the float levels are a bit high and need to be adjusted. Another possible cause could ...
|
| 1987 F 150 | 4/12/2008 |
Q: The transmission when put into drive hesitates for a few seconds before the truck moves. After it is ...
A: The easiest thing to do is to change the transmission fluid and filter. This has been know to fix ...
|
| Using retard control | 4/12/2008 |
Q: I have a 1923 Studebaker and it is my first vintage car Can you give me advise on driving her using ...
A: This is to set the spark timing back so that the engine will not kick back when starting. Retard the ...
|
| Studebaker 1950 | 4/11/2008 |
Q: I have a Studebaker Champion car 1950. I rebuilt the carburator and did all the adjustments as ...
A: There is a possibility that the float is sinking. This would allow the fuel under the diaphram that ...
|
| front end alignment specs | 4/11/2008 |
Q: I have a 1958 chevy biscayne with a 235 6cyl 2-door. Maunal brakes and steering. Can you tell me ...
A: The camber on that car should be 0 to +1 with a desired setting of 1/2 Pos. The camber ...
|
| Corvette Brake Line | 4/11/2008 |
Q: My wife is inheriting a 1961 Corvette 283/Auto with a ruptured brake line. I want to have it fixed ...
A: If you have a good place to work, and can get the car up high enough safely to work under it you can ...
|
| Corvette Brake Line | 4/10/2008 |
Q: My wife is inheriting a 1961 Corvette 283/Auto with a ruptured brake line. I want to have it fixed ...
A: The cost of repairing the brakes is going to depend on where the break is and the condition of the ...
|
| Camshaft | 4/10/2008 |
Q: I have 1977 corvette which needs a new camshaft.my Question is is it ok to fit a performance cam as ...
A: It depends on what you are going to do with the car. It has been my experience that a stock Vette ...
|
| Dome Light | 4/9/2008 |
Q: I have a 1966 Ford Mustang. The dome light does not work when the ignition is in the off position. ...
A: It would appear that some where in it's past it was owned by some one that wanted to sit with a door ...
|
| wheel alignment specifications | 4/8/2008 |
Q: Would you happen to know where I can get the manufacture's specs on a full alignment for a 69 mach 1 ...
A: I have the manufacturers specifications but first let me ask a couple of questions. 1. Are the ...
|
| 1962 bel Air Hood Springs | 4/8/2008 |
Q: We replaced our hood springs with what they called heavy duty springs to cure the problem of our ...
A: Before you go to heavier springs take a refrigerator magnet, you know like the ones that you hold ...
|
| 66 mustang fuel gauge | 4/6/2008 |
Q: The fuel guage on my mustang does not work. The person that I purchased the vehicle from recently ...
A: Ok, good report. Now we need to ground the fuel tank. I have several long, and I mean long jumper ...
|
| shocks removal | 4/6/2008 |
Q: i have a 1950 chevy fleetline stocker is the removal of the shocks a bit dangerous due to pressure? ...
A: The front shocks can be removed and installed without any danger no matter how you jack the car. It ...
|
| car pdoor seal | 4/5/2008 |
Q: The black gasket door seal is torn and a piece about 3 inches long and an inch wide is missing on ...
A: I have never had luck repairing door gaskets although a couple of guys say they have. If is not ...
|
| 66 mustang fuel gauge | 4/5/2008 |
Q: The fuel guage on my mustang does not work. The person that I purchased the vehicle from recently ...
A: Ah ha, this indicates an open in the circuit. It could be as simple as the wire disconnected at the ...
|
| 66 mustang brake light not working | 4/5/2008 |
Q: The right brake light on my 66 mustang will not work. The blinker and park light work just fine, ...
A: Ok, if you have no brake lights on either side then the problem is most likely the stop light ...
|
| 1966 Mustang Pony replace back up light switch | 4/4/2008 |
Q: Dale here. I am restoring a 1966 Mustang Pony, with automatic transmisson mounted on floor ...
A: The back up light switch is part of the neutral safety switch and is bolted to the side of the ...
|
| 1977 corvette diferrential | 4/4/2008 |
Q: My brother inlaw and i are working to get this car back on the road and noticed humming coming from ...
A: If you have bad bearings or gears replacement and repair is a good idea. The anti freeze in the ...
|
| 1981 corvette choke | 4/3/2008 |
Q: 1981 corvette 350 auto choke light on dash is on fast idle wont kick off & choke only opens about ...
A: According to my reference material it is supposed to be a two pole switch. One wire comes from the ...
|
| '73 camaro posi rear end "stutters" | 4/3/2008 |
Q: I recently purchased a 1973 camaro LT with the original rear end (posi option) and while driving it ...
A: Check with your local GM dealer and buy the rear end fluid they sell for the Posi. Change the fluid ...
|
| 1955 1st series chevy truck | 4/2/2008 |
Q: does anyone have a shifter box diagram or photo? i can put mine in 1 st won't come out unless i go ...
A: This is a common problem with Chevy three on the tree shifters. The shift forks and the housing were ...
|
| Car Floods | 4/1/2008 |
Q: My first and only car is a 1959 Ford Fairlane with a 223 6cyl engine, manual choke! The car starts ...
A: There is a gadget in the carburetor that is called a power valve. When the diaphragm in the valve ...
|
| brake problem | 4/1/2008 |
Q: I HAVE A 1955 CHEV. I RESTORED I PUT FRONT DISC BRAKE CONVERSHION KIT ON THE FRONT JUST CALIPER AND ...
A: That's fine, the booster looks good. It is possible that the front pads have been destroyed by the ...
|
| brake problem | 3/31/2008 |
Q: I HAVE A 1955 CHEV. I RESTORED I PUT FRONT DISC BRAKE CONVERSHION KIT ON THE FRONT JUST CALIPER AND ...
A: It could be the wrong booster or a defective booster. Now, check the booster. With the engine off ...
|
| brake problem | 3/31/2008 |
Q: I HAVE A 1955 CHEV. I RESTORED I PUT FRONT DISC BRAKE CONVERSHION KIT ON THE FRONT JUST CALIPER AND ...
A: There is more differences between the master cylinder for disc and drum brakes beside the ...
|
| 1981 corvette choke light | 3/31/2008 |
Q: the choke light on the dash stays on. fast idle wont kick off and the choke only opens up about 1/4 ...
A: The choke on these Rochester carburetors used an electric heater coil in the choke housing to supply ...
|
| 55 chevy brakes | 3/30/2008 |
Q: I replaced the front brake shoes on my 55 chevy, rebuilt the front wheel cylinders, replaced the ...
A: Boy do I wish that we had two way video on questions like this. So, lets start at the begriming. So ...
|
| 64 t-bird steering | 3/30/2008 |
Q: I have alot of play in the steering wheel going down the road.Checked the steering gear box and was ...
A: If it were my car I would have the box off the frame in a heart beat and check to make sure that the ...
|
| Fitting Piston Pins-!939 Chevy 1/2ton | 3/30/2008 |
Q: I have recently purchased a NOS set of GM pistons with the bushings and pins fitted in them. These ...
A: The piston pins should be fitted for a thumb fit when lightly oiled. If the pistons came from the ...
|
| 1960 Chrysler brakes | 3/29/2008 |
Q: My '60 Chrysler with power brakes, has a problem with the left front brake locking up. I have bled ...
A: You might want to check the other side and make sure that the wheel cylinder is working and that ...
|
| 64 t-bird steering | 3/29/2008 |
Q: I have alot of play in the steering wheel going down the road.Checked the steering gear box and was ...
A: You need to check this free play when the engine is running. To determine if it in the box or the ...
|
| 1963 Falcon - Tune up & Power Output | 3/27/2008 |
Q: I've got an old '63 Falcon Futura Convertible with a straight-6 170cc in it and a Ford-o-matic 2 ...
A: The distributor in that engine does not use a centrifugal spark advance system. The advance that the ...
|
| 1966 Fury Sport ,383, 4 barrel, auto trans. | 3/27/2008 |
Q: Brad, I asked a few questions about a week ago. Thank you for the answers they were very helpful, I ...
A: There should be one water temp sensor and it should be right on the front of the engine beside the ...
|
| wiper transmission replacement | 3/26/2008 |
Q: What is the procedure to replace a wiper transmission on a 1955 Chevrolet??
A: The windshield wiper set up on the 55 Chevrolet was certainly not one of GM's finest works. It is a ...
|
| 1963 Falcon - Tune up & Power Output | 3/25/2008 |
Q: I've got an old '63 Falcon Futura Convertible with a straight-6 170cc in it and a Ford-o-matic 2 ...
A: Well you are running a six cylinder engine that is less than 2.8 liters, a single barrel carburetor, ...
|
| AC Ace rear brake drums | 3/25/2008 |
Q: Any idea on how to remove the rear brake drums on a 1960 AC Ace? I've removed the rear wheel and the ...
A: Gotta use a wheel puller on that one. We used to use what my dad called a bingo cap. It was about a ...
|
| 1939 chevy | 3/24/2008 |
Q: I have the option of retoring the original front end suspension steering and brake system or I could ...
A: The answer to that is up to you and what you are expecting from the car. I have three very different ...
|
| "Sticky" Throttle .. | 3/23/2008 |
Q: I've recently started noticing on my 1970 Dodge Challenger (which I keep stored most of the year), ...
A: It sounds like it could be the fast idle cam on the side of the carburetor sticking. It is part of ...
|
| 1956 chevy sedan | 3/22/2008 |
Q: How do you remove the windshield wiper arms?
A: If the old gray matter serves me well it just slides down over the spline of the wiper transmission ...
|
| mg td oil leak | 3/22/2008 |
Q: My wifes 1952 MG TD is in great shape other than a major engine oil leak. Great oil pressure and ...
A: How about the word camshaft, or rocker box cover. The plug at the end of the cam shaft could be ...
|
| 1958 Primer for Pontiac Cheiftain 2Door | 3/22/2008 |
Q: Can you tell me what kind of primer was used on the 58 Pontiac? The car has been sitting in a ...
A: GM cars in that era were painted in lacquer and run a lacquer based primer. The primer that should ...
|
| rear main seal | 3/22/2008 |
Q: its leaking from the rear main i just want to know how to fix it? thanks
A: The best way is to pull the engine and check all bearing clearances when removing the crankshaft to ...
|
| Rust on Rotors | 3/20/2008 |
Q: Brad, Bought a new disc brake kit for my '64 Ford pickup. My rotors have been sitting in the ...
A: I would not worry about the rust on the braking surface as the pads will shine them up bright as a ...
|
| 1921 Car Won't Start | 3/20/2008 |
Q: I just got a 1921 Peugeot Type 161. This is a small 4 cylinder crank-start car with magneto. The ...
A: I am not familiar with this car. But engines whether French or not need three things to run. ...
|
| Cadillac electrical systems | 3/19/2008 |
Q: Did Cadillac ever use positive ground electrical systems? If so, what was the last year they used ...
A: Kent cadillac used positive ground through the twenties, thirties, and forties. By the time caddie ...
|
| 82 Corvette fuel pump relay location | 3/18/2008 |
Q: I am trying to resolve a fuel issue with a 1982 Corvette with crossfire injection. The car had been ...
A: The fuel pump relay on that car is behind the drivers seat. The fuel pump fuse should be marked as ...
|
| 1959 Plymouth | 3/16/2008 |
Q: Restoring '59 Plymouth. First mechanic I went to couldn't solve locking of drum brakes. Second ...
A: I can see where a young technician (under 60) would be a little miffed by at least the front brake ...
|
| corvette rear wheel bearings | 3/16/2008 |
Q: Brad! I thought your name sounded familiar! I am retired from Tate's Auto Service and I bought a ...
A: It has been a while since I tackled one of these puppies. The rear wheel bearings are tapered ...
|
| 64 T bird steering box | 3/15/2008 |
Q: Vern Thank you for your reply. Yes, i ahve removed all connections and am trying to pull the box ...
A: From what you have written I would agree that the problem is probably in the steering box. If the ...
|
| 1936 Dodge D2 Brake replacement | 3/14/2008 |
Q: I am replacing front and rear shoes on a 1936 Dodge D2 Sedan for the first time. These are the type ...
A: The cams that are half way up the backing plate are the adjusting cams. The pivot pins at the bottom ...
|
| mid 60's 383 MOPAR | 3/13/2008 |
Q: I have a friend with a mid 60's Plymouth. 383 motor, looks stock or close to stock. I want to help ...
A: Sorry to miss that part of it. Number one cylinder on any V rear wheel drive is the one that the ...
|
| mid 60's 383 MOPAR | 3/13/2008 |
Q: I have a friend with a mid 60's Plymouth. 383 motor, looks stock or close to stock. I want to help ...
A: Spark plug gap .035", point gap .017", dwell 28 to 32 degrees, Timing is a bit tricky. There are two ...
|
| 1956 Ford F100 issue | 3/13/2008 |
Q: I recently bought a 56 Ford F100, which I believe has the original 272 V8 in it. It runs, and it ...
A: Well it might be a bad fuel pump, a hole in the fuel line between the fuel tank and the fuel pump, ...
|
| Stiff steering won't self center | 3/11/2008 |
Q: In answer to your last question. No, it's not the loaded type. I have it only tight enough to not ...
A: Well that leads down to one of two possible problems. 1. A problem in the steering box. A control ...
|
| Stiff steering won't self center | 3/11/2008 |
Q: I have 67 mustang coupe with stock power steering. I can't seem to get the steering to free up and ...
A: Is the idler arm the rubber loaded type? If so, when the idler arm is installed the steering wheel ...
|
| Engine Swap..HELP! | 3/9/2008 |
Q: Shes a '62 Chevy C-10. It has the original 283 in her. I'm having the gas tank relocated and a bunch ...
A: You are asking the wrong guy. I like vehicles the way that the factory built em. At least the way ...
|
| Classic door hinge bolts | 3/9/2008 |
Q: I am looking for grade 8 door hinge bolts. I have a 1936 Pierce Arrow and cannot find the straight ...
A: I think that what you are looking for is called a machine screw. I use a company called Fastenal as ...
|
| power 1976 chrysler ny brougham | 3/8/2008 |
Q: Hard to get above 35mph. In park engine can rev up, in gear it trys to bog when approaching 35 and ...
A: Well as difficult it is for me to realize that catalytic converters are found on old/antique/classic ...
|
| '57 T-Bird Holley Carb | 3/7/2008 |
Q: Greetings Brad: I have recently come into ownership of my folk's 'T-Bird with the 312 CID engine ...
A: Back in the day I was a tun up and carburetor man at a metropolitan Boston Ford dealer.Vaughn Monroe ...
|
| 82 corvette/fuel pump/cross fire | 3/6/2008 |
Q: i have a 82 corvette and it just quit,i feel sure it's fuel related cause the injectors are not ...
A: The fuel pump is in the fuel tank and my best sources indicate that the tank just be dropped to ...
|
| 1970 Oldsmobile 2 barrel carburetor | 3/5/2008 |
Q: ok i have a problem my 1970 olds idles very rough when in gear. i have a feeling that its the ...
A: I am going to make a suggestion before you start messing around with the carburetor. I would suggest ...
|
| 65 Mustang | 3/4/2008 |
Q: My 1965 Ford Mustang owners manual says to use type "F" transmission fluid in the power steering ...
A: All of my old iron, including one Ford in this vintage, is running modern off the shelf good name ...
|
| 1955 ford fairlane country sedan/272 fordomatic | 3/2/2008 |
Q: Can you tell me how to adjust the neutral switch, I currently have to start the car in drive, also ...
A: The original switch was located at the base of the steering column and was mounted by a couple of ...
|
| 1921 Studebaker battery | 3/2/2008 |
Q: I just bought a 1921 Studebaker Light Six Touring car. Does it have a positive or negative battery ...
A: The neat thing about old cars is that as long as you do not try to start the car when installing a ...
|
| ignition system for 1950 Chevy 3800 truck (216 engine) | 3/1/2008 |
Q: I purchased a 1950 Chevy 3800 a couple of weeks ago but am having trouble getting it up and runing. ...
A: Just because the points and condenser look new that they are ok. A test light or a voltmeter will ...
|
| carb.. | 3/1/2008 |
Q: brad, i have a 1973 corvette (350) with 38,000 original miles..and yes it sat- stored alot... i,ve ...
A: There are a lot of reason for plugs fouling beside just attack the carburetor. I would suggest that ...
|
| Dodge Dart 1969 | 3/1/2008 |
Q: I am having trouble removing the clips from the front brake hose. I am replacing the hose and need ...
A: I assume that you are talking about the clips that hold the end of the hose that is attached to the ...
|
| 1950 Chevy powerglide | 3/1/2008 |
Q: My powerglide leaks at the rear main seal. Parts stores specializing in this vintage offer ...
A: I have used both the rope and the rubber seal. I prefer the rubber seal as long as you follow the ...
|
| 1966 Mustang ignition - lost key | 2/29/2008 |
Q: I've lost the ignition key to my 1966 Mustang Fastback - price quotes I've received from local ...
A: If you are good with an electric drill you drill the cylinder out of the switch mechanism. The trick ...
|
| 1951 235 chevy inline 6 distributor | 2/28/2008 |
Q: I recently purchased a classic 1951 Chevy that has a converted to electronic distributor. It quit ...
A: I am not a big fan of these 12 volt conversions. You can do it and keep the 12 volt system. Latch ...
|
| 1940 Buick Ignition Coil | 2/27/2008 |
Q: Dick Benjamin answered a previous question about a problem I am having about "no spark". I have ...
A: If I answer all three do I win the trifecta? Well lets try. First of all you will not need to get ...
|
| 1967 Volvo 122s motor mounts | 2/24/2008 |
Q: How do you change the motor mounts and how many are there?
A: There are two on the front sides of the engine and either one or two on the rear of the ...
|
| My car | 2/24/2008 |
Q: I have a 1972 slant six Plymouth Duster i have been restroing as a senior in high school and lately ...
A: Jason, here is what I am going to recommend. Take a trip to a Barnes and Noble or another good book ...
|
| 1963 Mercury Monterey Custom | 2/23/2008 |
Q: I am attempting to pullout my dash board, and I can not figure out why I can not pull my steering ...
A: The best way is to get a steering wheel puller. There are two threaded holes on either side of the ...
|
| 1963 Mecrury Monterey | 2/23/2008 |
Q: I have a 1963 Mercury Monterey and I am trying to get the front seat out. It is a powered bench ...
A: I think that the large rubber puck that you have found is the body to frame mount.I think a little ...
|
| 1967 Camaro, rosewood steering wheel horn contact. | 2/21/2008 |
Q: Brad, Hello and hope all is well. The horn contact under the horn button has come apart on me and ...
A: Good Morning: I assume that this is the three spoke simulated wood steering wheel that you have. As ...
|
| olds 350 rocket | 2/21/2008 |
Q: would you happen to know what the firing order and first cylinder is for a olds 350 rocket motor ...
A: I would like to know if the distributor is in the front of the engine or the rear. What year is the ...
|
| 1931 Buick | 2/20/2008 |
Q: I am selling a 1931 Buick for a friend of mine. Both of us are unsure what series Buick it is. Is ...
A: 1931 Buick Style Chart by SuperCar Specialty ...
|
| torino rocker panels | 2/20/2008 |
Q: I have an opportunity to purchase a 69 torino convertible. It will require new rocker panels to ...
A: The nice thing about restoring a Ford is that almost an entire new car, including Torino, can be ...
|
| Brakes | 2/19/2008 |
Q: I have 1951 Mercury, how do i adjust the brakes so i have more pedal? Second question when the time ...
A: Jack up and support the car on safety stands. Locate the adjusting slot on the bottom back side of ...
|
| Restoring a car through a school | 2/19/2008 |
Q: Brad, I own a 1961 Buick LeSabre that I have tried to restore for the better part of the last nine ...
A: In my years running auto repair programs in vocational and post secondary schools I never had a ...
|
| 1965 Ford Fairlane Sports Coupe | 2/18/2008 |
Q: I am trying to take off the existing dash face. Everything came off fine, except the headlight knob. ...
A: Ok, reach up under the dash and feel around on the headlight switch on the opposite side from the ...
|
| figure my truck out | 2/18/2008 |
Q: Hey dude my dad give me his old truck and i am restoring it..well i have no idea what the engine is, ...
A: Well sir, first of all you misspelled my name, it is Brad not dude. Secondly you need to give me ...
|
| 56 T-Bird door adjustments | 2/17/2008 |
Q: I am just completeing my full restoration of my 56 T-Bird and I am pulling my hair out about the ...
A: Open the door several inches. Grad the door at the back edge and lift. If the hood pins are loose ...
|
| Carb. vacuum | 2/15/2008 |
Q: Brad--I am replacing a R2GC carb. on my '58 Pont. with a Carter AFB 4 BBL copy (Edelbrock). The copy ...
A: Hopefully you still have the 2 barrel on the car. The easy way to check is to run the engine and ...
|
| 1950 Ford truck 239 motor firing order | 2/9/2008 |
Q: Rebuilding motor need firing order for 239 motor for 1950 ford f1
A: Spark Plug Make: Champion H10 Spark Plug Gap, Inch: .030 Firing Order: 15486372 (from front to ...
|
| spark plug wiring order for a 1972 corvette | 2/7/2008 |
Q: i have a 1972 corvette 350 small block. i would like to know in what order the wires go on the ...
A: Looking down on the distributor, the door to adjust the points should be just to the left of a line ...
|
| Brake Drum on 1964 Ford pickup | 2/5/2008 |
Q: Good morning, I am getting ready to take the brake drums off of my 1964 Ford Pickup, so I can ...
A: Is the truck a 100 series one half ton? three quarter ton and bigger use a heavy duty axle that ...
|
| Oil Leak | 2/4/2008 |
Q: I have a oil leak with my rear main seal. I have a 1957 cadillac seris 62 with a 365 cubic inches ...
A: If the engine is stock and has not been altered the rear main seal is a two piece affair. The upper ...
|
| 41 Packard Differential seal check | 2/4/2008 |
Q: We "blew" the rear end out of our '41 Packard on the Great Race. We patched it together with ...
A: The magic words, THE NUT CAME OFF! Now, does the nut look like a castlated nut but without the ...
|
| 41 Packard Differential seal check | 2/4/2008 |
Q: We "blew" the rear end out of our '41 Packard on the Great Race. We patched it together with ...
A: I would not hesitate to replace the pinion seal. the procedure that I would use is as follows: 1. ...
|
| 1977 GMC 4x4 th350 tranny | 2/3/2008 |
Q: when i 1st start the truck, it will run in all gears, when it gets warm/hot i only have low and ...
A: It has been my experience that the torque converter has very little effect on the shift points of a ...
|
| Help finding old headlights | 1/31/2008 |
Q: I'm writing to you from Hawaii with a request for some help. I am helping my boss restore a 1952 ...
A: Have you tried the plain old 6006/6012 sealed beam head light bulb as used in domestic cars of that ...
|
| Help finding old headlights | 1/30/2008 |
Q: I'm writing to you from Hawaii with a request for some help. I am helping my boss restore a 1952 ...
A: I am not sure that there is a correct headlight for this car. As there was only about 80 of these ...
|
| 1935 olds body by fischer | 1/28/2008 |
Q: Im wondering if chev body parts are the same only from a different year 35 36? there are no after ...
A: As far as I know there are cross over parts between the small series Pontiac and some Chevrolets, ...
|
| 70 el camino | 1/27/2008 |
Q: Im having problems with my tail lights. The driver side blinker and tail light works but passenger ...
A: Well it looks like you had two problems. If the running lights work it is time to use a voltmeter to ...
|
| Battery Overcharging | 1/26/2008 |
Q: Well, last Saturday (1/19) I wrote to you seeking assistance with my overcharging battery on my 64 ...
A: That is the next step. Use a needle to pierce the wire going to #3 connector and attach your ...
|
| 1966 Ford Mustang Convertible Mechanical Question | 1/26/2008 |
Q: I inherited a 1966 Ford Mustang Convertible. My uncle disabled it so no one would be able to drive ...
A: In cars with distributors there is a rotor under the distributor cap. This device sits on top of the ...
|
| 1968 camaro 4 wheel drum brakes | 1/25/2008 |
Q: I wrote about this problem before I did everything you told me to do, checked wheel cylinders, brake ...
A: Well I have kicked this one around in the old gray matter and the only thing that I can come up with ...
|
| 71-2 mustang engine I.D. tag codes | 1/25/2008 |
Q: Dear sirs I have a 73 mustang clone and am trying to identify the motor it is a K620 S G or the G ...
A: Jim, the numbers that you provided me do not exactly match anything in my reference library. So, a ...
|
| 65 Mustang windshild wipers and horn | 1/24/2008 |
Q: my mom just gave me back the Mustang muscle car I built in high school auto shop (first girl to do ...
A: Kristen, what school? I spent 50 years as a vocational instructor in one form or another including ...
|
| Nova gas tank mystery | 1/23/2008 |
Q: I recently bought an unmolested 71 Chevy Nova 350 2bbl four door with 80,000 original miles. For ...
A: There are three vent lines that run from the fuel tank to a liquid vapor separator. This unit may be ...
|
| 1976 Celica rear suspension | 1/22/2008 |
Q: Goodmorning, I have a 1976 Toyota Celica completly stock.A couple of months ago I decided to change ...
A: I would suggest that you go over the installation of the bushings. It sounds like one or more of the ...
|
| 1950 Chevy Powerglide | 1/21/2008 |
Q: I recently purchased a 1950 Chevy Sports Coupe with Powerglide in Montana. When driving it home, ...
A: You will need to check all of the regular tune up items including the vacuum advance unit on the ...
|
| 1967 Camaro (Horn Problem) | 1/21/2008 |
Q: I have 2 questions: I'm having a problem getting my horn to work on my 1967 camaro convertible. I ...
A: Well first of all a few questions. Have you jumped the horns to be sure that they work? Have you ...
|
| what engine is this? | 1/21/2008 |
Q: I have a 1978 VW Super Beetle convertible, it had a different engine put in it. The number on the ...
A: This was a replacement engine supplies by VW. This letter series was never according to my ...
|
| TIMING AND DWELL VARIATION | 1/20/2008 |
Q: Brad, I have a 1956 cadillac with a 365 4bbl. I recently replaced the plugs, wires, distributor, ...
A: Sorry about the insistence of verifying the meter but old habits developed as training manager for ...
|
| TIMING AND DWELL VARIATION | 1/20/2008 |
Q: Brad, I have a 1956 cadillac with a 365 4bbl. I recently replaced the plugs, wires, distributor, ...
A: I repeat my question about the accuracy of the dwell meter? Has it been checked and does your ...
|
| Overchargeing Battery | 1/20/2008 |
Q: I own a 64 Bonneville that is in very good condition, however I recently encountered a problem that ...
A: The voltage regulator on your car has 4 terminals. If your car has an idiot charge light on the dash ...
|
| TIMING AND DWELL VARIATION | 1/19/2008 |
Q: Brad, I have a 1956 cadillac with a 365 4bbl. I recently replaced the plugs, wires, distributor, ...
A: I have a coupe of questions. You mentioned replacing the distributor. Was it new, used, or rebuilt? ...
|
| Overchargeing Battery | 1/19/2008 |
Q: I own a 64 Bonneville that is in very good condition, however I recently encountered a problem that ...
A: Good morning Vince: Well, I think that we need to check the voltage at terminal 3 on the voltage ...
|
| 63 impala !!!!!! | 1/17/2008 |
Q: i am looking for some direction in selling a 1963 chev impala w/ 32,000 original miles...it has been ...
A: The first thing that I would suggest is to find some one in your area knowledgeable about old cars ...
|
| 1940 Packard 120 | 1/17/2008 |
Q: Electrical SystemI suspect the voltage regulator is bad. When the car is idling the voltage across ...
A: Well it sure sounds like someone has converted this nice old car to an 8 volt system. A question for ...
|
| Ford Pinto headlight switch removal | 1/17/2008 |
Q: How do you remove the headlight switch on a 1976 Ford Pinto? We pulled the instrument cluster out ...
A: There should be a small spring loaded button on the switch on the opposite side from the wiring. ...
|
| Fuel Tank Cleaning/Sealing | 1/15/2008 |
Q: Sears: I'll think I should replace the fuel pump on my 88 Pontiac Sunbird w/2.0L OHC engine (140K ...
A: Ok, a question for you. When doing the volume test where are you breaking the line to test volume? ...
|
| Fuel | 1/12/2008 |
Q: Hey, I have a 1964 Chevy II Nova, 4-dr sedan. I was driving and then it cut off, and now it won't ...
A: The only time that I know of that timing jumping while the engine is running and will cause the ...
|
| 1968 camaro 4 wheel drum brakes | 1/11/2008 |
Q: I have a 68 camaro with 4 wheel manual drum brakes. the system is all new except the proportioning ...
A: If I had the car in my shop with this history, I would have all four wheels and drums off. I would ...
|
| 1968 camaro 4 wheel drum brakes | 1/8/2008 |
Q: I have a 68 camaro with 4 wheel manual drum brakes. the system is all new except the proportioning ...
A: Several questions: 1. Is it power brake system? 2. Is the pedal firm when it is pushed down or is it ...
|
| Fuse in the light switch | 1/7/2008 |
Q: mine is a 1965 Mustang and my parking and instrument lights are not working. I plan on replacing the ...
A: Pulling the switch is not that bad a job, however I have been known to remove the four bolts/nuts ...
|
| Classic Mustang Purchase to Restore | 1/6/2008 |
Q: My husband is traveling a fair distance to look at a Mustang for me that is either a 1967 or a 1968. ...
A: Under the best of conditions these Mustangs would rust and you would end up with a moon floor. If ...
|
| 1974 chevy elcamino 350 sb | 1/3/2008 |
Q: when im driving and reach speed of 35 to 45 my car starts dying so I back off the peddle a little ...
A: The first place that I would look would be the fuel filter. Rochester 4 barrel puts the filter in ...
|
| Turn Signal Switch Replacement | 1/2/2008 |
Q: Brad, I'm the orig owner of a 1976 Jeep Cj-5 (man Trans). When purchased this vehicle came with a ...
A: As far as I can see the switch can be replaced while the column is in the car. You will need a tool ...
|
| 1970 Olds delta B body | 1/2/2008 |
Q: I have a 1970 Olds Delta 88 B body two door. With a chassis service manual, and a fisher (GM) body ...
A: Some of these cars used a switch that snapped into the hole and was held by a couple of springs. ...
|
| Turn Signal Switch Replacement | 1/2/2008 |
Q: Brad, I'm the orig owner of a 1976 Jeep Cj-5 (man Trans). When purchased this vehicle came with a ...
A: According to my old parts manuals a switch from that era, 1976 through 1984, with tilt wheels should ...
|
| mopar flathead 6 stuck | 1/2/2008 |
Q: I have a 47 Chrysler with a 250.6 L head 6. It was rebuilt some time in the 1960's and evidence ...
A: I just finished an engine rebuild on a 1953 CJ that was stuck like this. It has been my experience ...
|
| wiring problem - '56 FORD | 1/1/2008 |
Q: My turn signals work but I have no brake lights on my 56 ford. I can't find a wiring diagram for my ...
A: Well, if the directionals work and the stops do not then everything from the output side of the ...
|
| ~1948 Willys/Jeep engine replacement | 12/30/2007 |
Q: I am trying to get my grandfather's ~1948 m38(cj3a) [i think] running again which is going to ...
A: As far as I know the early Jeeps like yours has the low profile body. That limits a bit what engine ...
|
| Ign. wiring | 12/30/2007 |
Q: My typing skills are limited so please dont grade the grammer. Just bought 1939 ford 2 door, ...
A: Glad to hear that the rewiring and reverting back to 6 volt made it run but real sad about the ...
|
| master break booster | 12/28/2007 |
Q: need to know how to remove a master brake booster from a 64' chev imp. SS. 409 engine
A: The first step is to get up under the dash and disconnect the master cylinder push rod from the ...
|
| Ign. wiring | 12/27/2007 |
Q: My typing skills are limited so please dont grade the grammer. Just bought 1939 ford 2 door, ...
A: Well, I usually don't answer questions dealing with modifications because so much is subjective, ...
|
| Ign. wiring | 12/27/2007 |
Q: My typing skills are limited so please dont grade the grammer. Just bought 1939 ford 2 door, ...
A: OK James lets get serious here. First I love flatheads and own and drive a 41 coupe with offy heads ...
|
| lincoln hydramatic | 12/26/2007 |
Q: thank you jack
A: I love modern technology when working on old cars. If you check out the following site, ...
|
| Trouble starting, intermitent | 12/25/2007 |
Q: (Long e-mail alert) Hello. I have a 68 Pontiac Firebird 400 with a TH400 automatic transmission. At ...
A: Well with the new bit of information that the back up lights are or were out, that points directly ...
|
| carburetor leaks | 12/24/2007 |
Q: I have a 1960 - 283V8 with a Rochester 2GV carb (there is no tag but looks like the 2GV in the ...
A: A lot of these problems that appear to be carburetor leaks are actually percolation on hot shut ...
|
| 64 thunderbird | 12/24/2007 |
Q: My son and I put on a Holly 4 barrel on this 390 and it ran great for quite a while.It has started ...
A: It sound like you have a carburetor that is dumping more fuel into the intake manifold system than ...
|
| Carb and Points adjustments for 1966 TBird | 12/23/2007 |
Q: Your advice before helped out greatly, so I'm back again :-) Two guestions actually, what are the ...
A: One and one half to one and three quarter turn out is a base adjustment only. Then warm up the ...
|
| Trouble starting, intermitent | 12/22/2007 |
Q: (Long e-mail alert) Hello. I have a 68 Pontiac Firebird 400 with a TH400 automatic transmission. At ...
A: If the car starts when you press the starter button but will not start with the ignition switch the ...
|
| 90 firebird cooling fan | 12/19/2007 |
Q: My 1990 firebird operates the cooling fan when the a/c pressure switch activates but not when the ...
A: The electric cooling fan is controlled by the engine management computer. It gets information from ...
|
| '49 Ford gas gauge | 12/18/2007 |
Q: I'm looking at a '49 Ford Fordor to purchase - the car is 95% original. One of the minor problems ...
A: These gauges are easy to find, and there are those that will rebuild them. It sounds like the dash ...
|
| Modulator valve | 12/17/2007 |
Q: I bought a 1968 Olds Cutlass convertible. It has a 2 speed transmission that looks rebuilt. It ...
A: A couple of things to check here. Make sure that there is manifold vacuum at the modulator and that ...
|
| FIRING ORDER OF A 1964 CAD 429 ENGINE | 12/12/2007 |
Q: Is the number one piston on the right or left bank of a 429 cadillac deville 1964 model?
A: A couple of tricks for finding number one cylinder on a V type engine. Standing in front of the car ...
|
| 1973 Plymouth Duster, Hesitation | 12/12/2007 |
Q: I've been working on my '73 duster and can't seem to get rid of a hesitation it has in the middle ...
A: What is column C? Dare I ask? This car was a bear to get running right when it was new due to the ...
|
| no spark in q 1966 T-Bird | 12/11/2007 |
Q: I recently got a '66 T-Bird that was in storage for 25 years. Followed the procedure of pouring ...
A: Question. Spark at the points or at the plugs? Just a thought. The Ford distributor uses a ground ...
|
| 77 corvette | 12/9/2007 |
Q: I AM LOOKING FOR THE TORQUE SPECKS FOR THE PINION NUT AND THE CARRER COVER FOR MY 77 VETTE. CAN ...
A: Ok Scott, lets give it a try, the pinion nut does not have a specific torque. It is a self locking ...
|
| 1963 falcon transmission | 12/8/2007 |
Q: Purchased a 1963 ranchero. Bad shape. The whole tranny and motor shake when trying to engage in ...
A: Paul, I need a whole lot more information to be of any help here. First, does the engine run ...
|
| 69 Mach 1 Mustang | 12/6/2007 |
Q: A few years ago we bought a Mach 1 and the wiring on it has been worked and an alarm system added ...
A: Oh boy, here we go again straightening out a mess created by an after market installer. And back in ...
|
| mercedes injectors | 12/6/2007 |
Q: 0n my number 4 and 8 injectors the plug that plugs into the injectorhas no fire to it, the other 6 ...
A: That appears to be the control module for the injection system. It sound like the transistor inside ...
|
| starting engine | 12/6/2007 |
Q: on my 47 plymouth,I put in rebuilt carb,fuel pump, points, rotor, plugs. When I went to start it, it ...
A: Ok Ed here we go. Once you get everything replaced and checked remove number one spark plug. Cover ...
|
| vacuum modulator valve | 12/6/2007 |
Q: i cant seem to locate where the vacuum modulator valve could be on my 1980 cadillac eldorado ...
A: If the transmission is the original the modulator should be on the side of the case in front of the ...
|
| tranny shifting | 12/5/2007 |
Q: 89 pontiac grand am with 3 speed auto. tranny will not automatically shift into third gear unless i ...
A: This car, the 2.5 liter engine, uses a throttle cable to provide the transmission with driver ...
|
| Autolite ignition | 12/5/2007 |
Q: Mr Sears, Can you tell me where I can buy parts for antique autolite ignitions? I need new points, ...
A: I have ALWAYS been able to get an engine, if it was in good condition, to run well on the stock ...
|
| starting engine | 12/5/2007 |
Q: on my 47 plymouth,I put in rebuilt carb,fuel pump, points, rotor, plugs. When I went to start it, it ...
A: Oh boy. Well the first thing that you will need is probably a new starter solenoid. In cranking for ...
|
| mercedes point gap | 12/5/2007 |
Q: i have a 1973 mercedes 450sl. could you please tell me what the points gap on. also this car is not ...
A: According to MB the points are gapped using a dwell meter at 30 to 34 degrees. However this ...
|
| 79 Cutlass | 12/3/2007 |
Q: '79 Cutlass, 260 Engine. Weather is turning colder so I warm up my cutlass for 3-4 minutes. When I ...
A: What you are experiencing is the reason that we have gone completely to fuel injection. Given the ...
|
| vw beetle starter problems | 12/1/2007 |
Q: I am rebuilding a 1972 beetle, we put on a new starter and we turn the ignition switch the car ...
A: This could either be a starter solenoid sticking or the ignition feed wire that is supposed to be ...
|
| 67 cadillac engine | 12/1/2007 |
Q: What oils the timing chain and distributor gear.I just rebuilt engine and there is no oil under the ...
A: The timing chain and the mechanism mounted in the timing case or front covers is lubricated by throw ...
|
| External Oil Pathes on a 53 Nash 235 Six | 11/30/2007 |
Q: I am working on a 53 Nash-Healey with the 235 Six. There are three oil fittings (Ports) on the ...
A: Ok, lets do a little "007" work here and see what is going on. First the fitting that says filter ...
|
| blower question part 2 | 11/29/2007 |
Q: Sorry, I guess my question wasn't very clear. I have a 66 Chevelle SS396 w/factory air. This car ...
A: Ok, I think that I understand the question now. If memory serves me well enough, that condenser pig ...
|
| blue smoke from tailpipe | 11/28/2007 |
Q: I am interested in purchasing a 1977 chevy el camino with 305 v8. The car has a puff of blue smoke ...
A: A puff of smoke when you goose the engine is usually a sign that there is some engine oil getting by ...
|
| 66 mustang | 11/27/2007 |
Q: my 66 mustang will be running one minute then sputtering and dying the next. if i try giving it gas ...
A: Katelyn, it sounds like, based on your sense of smell, like it could be a flooding carburetor. That ...
|
| Fuel tank sending unit | 11/26/2007 |
Q: I just purchased a 67 Ford Galaxie. The fuel gauge was not responsive so I did some digging... The ...
A: A few questions. Was the new Sender new or used? Was it new old stock? Did it come with a new ...
|
| Replace motor | 11/26/2007 |
Q: I have 1965 Ford Thunderbird I will be replacing the 390 motor in the car, my question is the repair ...
A: Ok, here is the skinny on securing the Torque Converter. When you remove the nuts or bolts that hold ...
|
| 1974 Corvette Engergency Brake Light | 11/25/2007 |
Q: I just purchased a nice 1974 Corvette Coupe. The emergency brake light is always on even on the ...
A: Is the light just for the E Brake or does it say brakes. If the car has a double master cylinder it ...
|
| 1967 Mustang | 11/25/2007 |
Q: I am restoring my 67 mustang I am looking for an exploded view of the 200 six cyl engine or a ...
A: Check the following web sites: http://www.billwrigley.com/vintage/216.jpg. My standard answer to any ...
|
| early 60's ford econoline truck | 11/21/2007 |
Q: I'm purchasing an abandoned econoline tuck through a lien sale. It's been sitting for about 20 ...
A: The data plate should be attached to the drivers door. If it is not there I know of no other place ...
|
| 1951 Mercury | 11/21/2007 |
Q: Brad The electric fuel pump is mounted on the main frame about 20" in front of and below the gas ...
A: If the electric pump is mounted 20 inches away from the tank that means that it is forward of the ...
|
| door hinge pin removal 1951 chevy p/u | 11/21/2007 |
Q: I am trying to remove & replace the hinge pins and bushings on my 51 chevy truck.I have soaked with ...
A: The problem with all the pounding is that you have managed to expand the pin so that it makes it ...
|
| 1958 Skyliner dash lights | 11/20/2007 |
Q: I guess I wasn't responding correctly since I didn't hear from you. My son and I were able to get ...
A: Either the motor has failed, a problem with one of the relays mounted in the back, a bad ground (and ...
|
| 1958 Skyliner dash lights | 11/20/2007 |
Q: I guess I wasn't responding correctly since I didn't hear from you. My son and I were able to get ...
A: Please send me a little more information: Has the car been restored? Does the trunk lift when you ...
|
| 1968 plymouth fury 3 droptop | 11/20/2007 |
Q: I have a 383 V8 engine I think Im have transmission problems. I got filter replaced and new fluid. ...
A: Eric, this car is NOT equipped with a vacuum modulator. It does have a throttle rod running from the ...
|
| 85GMC C2500 6.4, 4sp, 1T. Axle LB | 11/19/2007 |
Q: Parked her in 2000 because after the engine rebuild she would not quit blowing head gaskets,heads, ...
A: If you are going to do a complete restore the problem should be corrected in the rebuild. Pay close ...
|
| Battery draw 80 corvette | 11/19/2007 |
Q: 1980 stock corvette. I have a draw on the battery, battery dies in 2 days. I removed the Negative ...
A: Robert, all cars built in the electronic age have what we call parasitic draw. The electronic age ...
|
| 85GMC C2500 6.4, 4sp, 1T. Axle LB | 11/18/2007 |
Q: Parked her in 2000 because after the engine rebuild she would not quit blowing head gaskets,heads, ...
A: Good morning. I do not find a listing for a 6.4 liter diesel in your model year. I find a 6.2 with ...
|
| 1966 Mustang Turn Signal Problem | 11/17/2007 |
Q: I purchased a 1966 Mustang coupe about four years ago. It had been stored in a barn for about 13 ...
A: It would appear to me that the problem is in the new right side lamp or wiring, as everything seamed ...
|
| Stock 49 mercury engine exaust | 11/17/2007 |
Q: I have a stock 49 mercury with the flathead v8. Every time we start the car, we get covered with ...
A: Sounds like one of two issues. First contamination in the oil pan. Try an oil change and a filter ...
|
| 1967 Ford Mustang Transmission | 11/15/2007 |
Q: I have a 67 Mustang with a 289 engine. It has an automatic 3 speed transmission which leaks. I've ...
A: This is one of those cases that it is an "in my opinion". You are going to have to remove the ...
|
| 1967 Ford Mustang 289 no spark | 11/13/2007 |
Q: We recently bought the car and are working to get it running. The car will turnover but has no ...
A: OK, there should be a solid 12 volts at the coil when the - side of the coil is disconnected. That ...
|
| carburetor | 11/13/2007 |
Q: I have a 1965 plymouth Fury with a 318 2 barrel Carter carburetor, and i was told the accelerator ...
A: The accelerator pump probably was in a cardboard tube to protect it in the package. Flared simple ...
|
| 1967 Ford Mustang 289 no spark | 11/11/2007 |
Q: We recently bought the car and are working to get it running. The car will turnover but has no ...
A: Well here are some things that you need to do and get back to me with the answers. First disconnect ...
|
| possitive 6volt charging system in a plymouth | 11/11/2007 |
Q: what goes where? is there a wire besides the ground and hot that conects the battery to something ...
A: I need you to answer a few questions for me. First is the wiring in the car as from the factory or ...
|
| 72 el camino VIN# | 11/9/2007 |
Q: I have a 1972 el camino the brake combination valve has a push button on it. What exactly is this ...
A: Ok, here goes. 1= Chevrolet D= Sales Code 80= Body Style ElCamino H= Engine code 2= Model year L= ...
|
| 1952 Pontiac straight eight engine rebuild. | 11/8/2007 |
Q: I need an exploded view of the timing case cover showing all parts, including any gaskets and such ...
A: An engine gasket makers parts manual or the factory parts book would probably be your best bet. My ...
|
| 49 Cadillac Hydramatic gearbox | 11/7/2007 |
Q: Gearbox has a problem/1st to 2nd gear shift is fine' 3rd to 4th is also fine' the 2nd to 3rd gear ...
A: This transmission was never known for it's smoothness in fact when it first was let loose on the ...
|
| Firing Mechanism | 11/7/2007 |
Q: Can you tell me the firing order for a 1979 Ford F100 (302)? Can you tell me how the distributor cap ...
A: The firing order is 1-5-4-2-6-3-7-8. The cylinders are number with 1-2-3-4 on the right side of the ...
|
| delco reamy alternator wiring | 11/6/2007 |
Q: I have a delco reamy alternator with batt-ground-r&f terminals. A vr273 voltage regulator with ...
A: Hopefully the original wiring to the ammeter is still in the vehicle. If so then the wire that went ...
|
| 66 CHEVY BEL AIR | 11/6/2007 |
Q: I have a 66 chevy bel air and i've been searching for restoration parts everywhwere. I can't find ...
A: Carl, the best answer that I have for this and everyone that asks where can I get parts, is to get a ...
|
| Austin Healey Starter Solenoid | 11/6/2007 |
Q: I have a 63 Austin Healey Sprite that is having starting problems. We had to replace the starte ...
A: Well it is time to break out the old voltmeter and start chasing down the wiring, starting at the ...
|
| 1950 Plymouth VIN Location | 11/5/2007 |
Q: Where is the VIN location of 1950 Plymouth? This person is saying that it is the number that is ...
A: The number on the drivers door frame is the VIN for your 1950 Plymouth. The number stamped on the ...
|
| idle surge 56 Caddy | 11/4/2007 |
Q: I have a 56 Caddy series 62 with a 365 engine without AC, my problem is the idle surges, I recently ...
A: The main reason that non air conditioned cars have dash pots is to slow down the closing of the ...
|
| 1965 Buick Riviera GS | 11/4/2007 |
Q: What tools do I need to change the gas filter on a 1965 Buick Riviera GS? and is there a good manual ...
A: The fuel filter on that car is inside the fuel inlet on the carburetor. You will need a tubing ...
|
| ticking from left side of motor | 11/3/2007 |
Q: ANSWER: You need to do some 007 James Bond work for me. Check the following and let me know: 1. Is ...
A: Gad Zooks, it sounds just like a blown exhaust manifold gasket at one cylinder or just a loose ...
|
| ticking from left side of motor | 11/3/2007 |
Q: hello I have a 1977 checvy caprice cllassic about a week ago it started making a loud cliking noise ...
A: You need to do some 007 James Bond work for me. Check the following and let me know: 1. Is the ...
|
| delco reamy alternator wiring | 11/1/2007 |
Q: I have a delco reamy alternator with batt-ground-r&f terminals. A vr273 voltage regulator with ...
A: Well lets give this a try and see if we can get it wired for you. On the alternator Battery and ...
|
| Son seeks education | 10/31/2007 |
Q: My 18 year old son ...wants to attend a school that will teach him antique car restoration.He isn't ...
A: I am glad that you wrote. The best antique auto restorers that I have ever known cam from the ...
|
| 67 grand prix | 10/29/2007 |
Q: will removing the smog pump increase power? thanks
A: Although many claim yes dyno testing has proved just the opposite. The smog pump puts oxygen into ...
|
| flathead | 10/29/2007 |
Q: Cleaning out a old barn and found a old Chrysler flathead 6. I'm having a hard time finding age of ...
A: Charles, on the top front corner of the left side of the engine, right below the cylinder head, ...
|
| Headlights | 10/29/2007 |
Q: On my 1970 Chevy C10 Pickup Truck, I have replaced the headlight switch, fuses, and put in new ...
A: Well the one thing that you did not mention is the headlight dimmer switch located on the floor ...
|
| 1968 Mercury Cougar Brake Lights | 10/28/2007 |
Q: The brake lights on my 68 Cougar are staying on, when the car is on/off. It's not all the lights ...
A: OK, after doing a bit of research it comes down to a defect in the stop light switch or linkage ...
|
| '49 Packard Shift Problem | 10/27/2007 |
Q: Brad - I exceeded my allotment of followups so I need to ask a new question. I removed the two ...
A: Well I am glad that we are making progress. However, I think that the job is going to get a little ...
|
| Chevy 235ci hesitation | 10/27/2007 |
Q: I have a 1954 Chevy 1/2 ton with a 235 six engine. It was rebuilt 20,000 miles ago. The engine has ...
A: The answer is yes there could be a leak between the intake and exhaust manifolds. The easiest way to ...
|
| overdrive | 10/26/2007 |
Q: i just bought a 1964 chevy pick up.all original cab.it has a sticker by the ignition key that ...
A: I may be way off base here but I think that some one is messing with your head. I remember seeing a ...
|
| 1985 Chevrolet Celebrity | 10/26/2007 |
Q: I just came into ownership of a 1985 chevy celebrity with 26,000 miles. Garage kept, mint ...
A: Well in my opinion your mechanic is right on target. Inside the carburetor the accelerator pump is a ...
|
| '49 Packard Gear Shift Problem | 10/25/2007 |
Q: Brad - My '49 Packard Custom Eight (with OD) gear shift lever is locked in the reverse position. ...
A: If the two shift levers want to move as a unit it indicates to me that the pin that runs through the ...
|
| gutless 67 caddy | 10/25/2007 |
Q: and thanks for answering my last question on a leaky tran. I pulled it out and had it rebuilt so no ...
A: It is time to verify the condition of the engine. Time to take a compression test. That way you ...
|
| 1939 buick eight | 10/25/2007 |
Q: I have recently been able to buy this classic. It has been garage kept since the 50's, in a damp ...
A: The Buick club is www.buickclub.org. Next step is to subscribe to Hemmings Motor News the bible of ...
|
| gutless 67 caddy | 10/25/2007 |
Q: and thanks for answering my last question on a leaky tran. I pulled it out and had it rebuilt so no ...
A: The way that I would approach this problem in my shop would be to first run a compression test on ...
|
| '49 Packard Gear Shift Problem | 10/23/2007 |
Q: Brad - My '49 Packard Custom Eight (with OD) gear shift lever is locked in the reverse position. ...
A: The two shift levers with linkage that goes to the transmission actually shift the gears. One is for ...
|
| Front Brake drums | 10/23/2007 |
Q: I have a 1953 Chevy 1/2 ton pickup. I am repairing the brakes. I have completed the back brakes ...
A: The front brake drums are riveted to the front hubs. Well rivet may not be quite the correct word as ...
|
| '49 Packard Gear Shift Problem | 10/23/2007 |
Q: Brad - My '49 Packard Custom Eight (with OD) gear shift lever is locked in the reverse position. ...
A: It sound like there is wear in the shift levers at the bottom of the steering column. With someone ...
|
| 1968 Camaro door spring installation | 10/23/2007 |
Q: Howdy! I got my 68 Camaro back from the painter in slightly more than basket case condition (that's ...
A: I have been known to put the springs in a vise and squash it. Then with the spring compressed wire ...
|
| Ignition switch | 10/22/2007 |
Q: I am trying to remove the ignition switch on a 1063 Ford Falcon; everything under the dash has been ...
A: Good, I was hoping that would be the case. Now there should be a small hole just below the key. That ...
|
| The carb. is a Stromberg EE-16 which may have been rebuilt. | 10/22/2007 |
Q: Benjamin has been responding to questions on a 40 Packard with a Stromberg EE-16, carb which may ...
A: At this point I would certainly replace the needle and seat. Probably trying to find a metal needle ...
|
| 1951 chev p/u with 235ci | 10/22/2007 |
Q: My ignition system is not working correctly. I was running a 12 volt coil with a resistor to bring ...
A: We used to call the glow around the ignition system corona, and most of it was normal. The arcing ...
|
| 1949 ford f150 engines | 10/21/2007 |
Q: My son bought a 1959 Ford F150 and got two spare engines and many other extra parts. He wants to ...
A: My best answer is to pick up a copy of Hemmings Motor News, the worlds largest classified ad book ...
|
| steering | 10/21/2007 |
Q: how to adjust 1954 mercury steering box? ANSWER: Does the car have manual or power steering and is ...
A: OK, here we go. 1. Jack up the car so that the front wheels are clear of the ground. 2. Locate the ...
|
| old diesel engine | 10/20/2007 |
Q: is there a possible serious problem to a diesel engine, 82 Mercedes, that has been sitting for over ...
A: These old Mercedes Diesels are basically truck and taxi engines and are built to last several ...
|
| 1962 falcon clutch problem | 10/20/2007 |
Q: I have a 1962 ford falcon with original 6 cylinder, and 3 speed manual trans. I went to start it ...
A: That original e cross shaft that I referred to in the original answer. It rotates on two balls, one ...
|
| The carb. is a Stromberg EE-16 which may have been rebuilt. | 10/20/2007 |
Q: Benjamin has been responding to questions on a 40 Packard with a Stromberg EE-16, carb which may ...
A: I hate to step into the middle of a problem when another expert has been involved. Not good ...
|
| old diesel engine | 10/20/2007 |
Q: is there a possible serious problem to a diesel engine, 82 Mercedes, that has been sitting for over ...
A: Well it has rested long enough and it is time to twist it's tail. The first step is to see if it ...
|
| 1962 falcon clutch problem | 10/19/2007 |
Q: I have a 1962 ford falcon with original 6 cylinder, and 3 speed manual trans. I went to start it ...
A: If my old gray matter serves me right there should be a nut on each side of the square block and ...
|
| 1962 falcon clutch problem | 10/19/2007 |
Q: I have a 1962 ford falcon with original 6 cylinder, and 3 speed manual trans. I went to start it ...
A: Dennis, this answer is based strictly on past experience. The spring that returns the clutch pedal ...
|
| 235 timing advance/octane/gas mileage | 10/18/2007 |
Q: I was hoping you may be able to offer me some advice. I have completed a full body-off restoration ...
A: If you are getting 19 miles per gallon on that truck, I would saw that you are about max'd out. I ...
|
| 1950 Ford Hood | 10/18/2007 |
Q: My hood sits approx. 1/4 inch below the fender line. Is there a way to adjust the hood so it is ...
A: If it sits low in the back the hood hinges can be adjusted. If it sits low in the front there should ...
|
| Choosing the right Carb for 68 Buick 350. | 10/18/2007 |
Q: I have a 68 Skylark with orginal 350 recently rebuilt. Bored 20 over just to true it up. Stock ...
A: Jay, I am a charter member of the "If It Ain't Broke, Don't Fix It" club. Now this is just my ...
|
| Engine Stalling when warm | 10/16/2007 |
Q: I've got a 69 Pontiac GTO with a similar proplem to your recent inquiry about a 67 camaro 350. Mine ...
A: Your car starts right up after it stalls and that should indicate that it is not a sinking float or ...
|
| 1967 CAMARO 350 KEEPS CUTTING OUT | 10/15/2007 |
Q: MY CAR WILL START AND IDLE WITH NO PROBLEM AFTER A FEW MINUTES IT STARTS TO DIE, GIVE IT MORE GAS ...
A: Ok, that is good because in a modified car there is just too much that has been altered to try to ...
|
| 38 Packard Starting problem | 10/15/2007 |
Q: I have a rebuilt 38 Packard Six cylinder. The engine will not turn over with the 6 volt battery. It ...
A: Way back in the age of the dinosaurs when we used to build our own tow trucks, we rigged two six ...
|
| 1940 Chevy coupe | 10/15/2007 |
Q: What can you tell me about the oil system in this 216ci. engine? Ihave heard it's only partialy ...
A: Oh you are so right on target about the oiling system in the 40 Chev. It is a low pressure system ...
|
| 12v to 6v model a horn | 10/15/2007 |
Q: What is the best way to reduce voltage to 6 volts so I don't burn up a model a horn?
A: There is a device sold on the market called "Volt A Drop" which is a voltage dropping resistor. I ...
|
| Ford 65' Mustang | 10/14/2007 |
Q: Smoke keeps coming out of my exhaust and sometimes it will spit a liquid substance like water on the ...
A: The color of the smoke is an important clue here. Black is unburned gasoline from too rich a fuel ...
|
| 66 Vette Problem Starting when hot | 10/14/2007 |
Q: I have a 1966 corvette coupe 327/350. After I take the car out for a drive, when I shut if off I ...
A: It is quite normal to have to pump the gas pedal once or to hold it 1/4 way down when starting a ...
|
| 1966 jeep wagoneer | 10/14/2007 |
Q: I am buying a 1966 jeep wagoneer. It has been sitting where it is for about five years. Well I was ...
A: I am going to risk a bad rating and answer this one in a public forum. This sounds like the perfect ...
|
| hot 65 impala | 10/13/2007 |
Q: I have a 1965 impala super sport with out air. All original as far as I can tell. When the car is ...
A: If the motor spins but does not fire there could be three problems. First you have a problem in the ...
|
| !958 Ford dash lights | 10/12/2007 |
Q: The dash lights don't work on my 1958 Ford Skyliner. The headlights, parking lights, tail lights ...
A: I will be waiting to hear what you found. The dash lights should be connected to the rheostat that ...
|
| turn signal ground problems | 10/12/2007 |
Q: On my 1961 Plymouth Fury my left turn signal is not working. I replaced the lamp, and it would only ...
A: It sounds like the rust mice are having their way with your poor Plymouth. In cases like this I have ...
|
| 1965 CORVETTE ELECTRICAL TROUBLECSHOOTING | 10/12/2007 |
Q: New temp sending unit. Bled the cooling system. After driving only one block, gauge is pegged and ...
A: OK, you say the motor is cool to the touch. I would like to know what the temperature is right ...
|
| vac./emiss. hoses | 10/12/2007 |
Q: I have a 1978 ford e-350 with a 460 in it. There is no vac./emiss. info to be found on or in it. ...
A: If your vehicle is rated at 10,000 pound the maker, Ford, may not have been required to put the ...
|
| dimmer switch | 10/11/2007 |
Q: i have a 37 pontiac street rod with a gm sterring column the dimmer switch is bad,i have been to 4 ...
A: Bob, you sure can use the floor mounted switch and wire it into the wires that you remove from the ...
|
| Power Brake Booster | 10/10/2007 |
Q: I took apart a power booster on a custom royal dodge 1956. It seems ok but i can't really tell why ...
A: The test that we have used for years when checking the operation of a vacuum operated power brake ...
|
| 1967 Ford Galaxie 500 alternator problems | 10/10/2007 |
Q: I have a 1967 Ford Galaxie 500 4door with AC and power steering and I had an alternator and it ...
A: Never polarize an alternator system, you will fry the diodes in the alternator and could end up with ...
|
| 1946 Ford doors | 10/9/2007 |
Q: Brad, I recently purchased a 1946 Ford coupe street rod. It is great except the doors were rehung ...
A: I have never found a manual that really helped adjust doors. I had the same problem on my 1941 Ford ...
|
| Radiator question... | 10/9/2007 |
Q: Mr. Sears: I've got a 1979 El Camino (350 engine) with air conditioning. (Not sure how "classic" it ...
A: David, I am not a fan of used radiators. We cannot see inside the radiator to check for the buildup ...
|
| 1967 dash lights | 10/9/2007 |
Q: i have a 1967 mustang that the dash lights don't work. i found a female wire connector hanging loose ...
A: Judging from what you ave told me it sounds like the dash light wire that connects to the headlight ...
|
| Ignition Key Cylinder Removal for 1966 Mustang | 10/8/2007 |
Q: I believe I need to drill out the ignition key cylinder for the Mustang I bought so I can put in a ...
A: First of all the door locks and ignition locks used a separate key in this era. I am not a fan of ...
|
| '25 Chev mechanical gas gauge cap | 10/8/2007 |
Q: Do you have a recommendation for where I might look for a gas gauge fuel tank cap, such as Marvel ...
A: As always when asked a question "where can I find..." the answer is always the same. Start reading ...
|
| 67 ford lifters | 10/8/2007 |
Q: I have developed lifter noise after truck sat a while. runs very strong. I changed oil. Left side is ...
A: Had to go back into my notes from the 60's to find the answer to this one. The left bank of lifters ...
|
| Firing Order | 10/8/2007 |
Q: Can you tell me the firing order for a 1976 Ford F-100 5.9 engine (390)? Also doe the distributor ...
A: The firing order is 1-5-4-2-6-3-7-8 with number one being the first cylinder on the right bank, that ...
|
| Powerglide trannsmission | 10/6/2007 |
Q: I have Chevy Malibu 1968 6 cyl with 2 speed powerglide transmission . My problem is with the ...
A: The most common cause of this problem on this transmission is usually the vacuum modulator located ...
|
| 67 Ford F100 gears lock up | 10/5/2007 |
Q: Driving my recently acquired 67 Ford pickup with "3 on the tree," the gears stuck 3 different times ...
A: The problem is a common one with vehicles with the column mounted shifters. The shift forks at the ...
|
| choke thingee | 10/5/2007 |
Q: I know nothing about cars but have recently got an automatic 75 ford escort. It starts up fine but ...
A: There is a problem with the question. American Ford escorts did not appear on the market until the ...
|
| 1972 chevelle | 10/2/2007 |
Q: the timing is definitly correct i am sure of that any info you have would be great thanks
A: I'll be willing to bet at least twenty five cents that the distributor is off by 180 degrees. The ...
|
| Brake Light 1967 Lincoln Continental Convertible 462- 4 Barrel | 10/2/2007 |
Q: How do you reset the brake light so that it will go off ?
A: I assume that you are talking about the Brake light on the dash not the stop lights on the rear of ...
|
| 1965 Corvette water leak | 10/2/2007 |
Q: Every time I wash my corvette I notice water puddled up on the floor mats. I can't figure out if ...
A: You have to find the leak before you can fix it or I can suggest a fix. Take your handy dandy flash ...
|
| Fuel gauge 1970 Chevy c10 truck | 10/1/2007 |
Q: I just purchased a fully restored 1970 c-10 and the fuel gauge doesn't work. How/where should I ...
A: On a fuel gage problem I usually head for the fuel tank. Find the harness connector that will ...
|
| 1929 Lincoln firing order? | 10/1/2007 |
Q: I need to find the firing order on a 29 lincoln Model L golf coupe 8 cylinder.
A: The best information that I can find is 15486372. Number one cylinder can be found by looking down ...
|
| 1992 Chevy Caprice Classic | 10/1/2007 |
Q: My dad bought a Chevrolet Caprice Classic in 1992, died in 1996. It has been in my garage since. I ...
A: This is one of those impossible to answer questions but I am doing it in open answer form rather ...
|
| 1974 chev 350 pickup | 9/30/2007 |
Q: i replaced the oil pump and would like to know how to install the distributor and how to set the ...
A: OK Bobby, this is going to be a long answer as you have about 6 different operations in here. The ...
|
| wheel advise | 9/29/2007 |
Q: I just bought a 1950 Chrysler Windsor (4 door) but having trouble getting tires to fit on the front, ...
A: It would appear that the problem is one of two possible things. First some one may have changed the ...
|
| 1951 GMC 1 ton | 9/28/2007 |
Q: Is this truck negative or positive ground?Totally stock truck.
A: According to my best sources here it should be a negative ground. On any vehicle pre electronics ...
|
| Horn not working | 9/28/2007 |
Q: 1- I verified the horns and both work when put direct with the battery 2- changed the horn relay but ...
A: Ah Ha, but did you verify that there was voltage at the relay, or that the wire going from the ...
|
| 1962 Ford Falcon | 9/26/2007 |
Q: My grandson, also Harold A. Doede, has a 1962 Falcon, 6 cylinder, 3 speed on the tree. This car is ...
A: Harold, this is one of those "found in a barn" stories that usually you hear about 4,286th hand. The ...
|
| 1951 Studebaker Champion oil dipstick | 9/24/2007 |
Q: I was wondering if the dipstick we have for a 1951 - 1954 Studebaker Champion will work for a 1950 ...
A: The best way to check is to drain the oil and refill with the correct amount. Then use the dip stick ...
|
| Sunbeam Alpine clutch | 9/24/2007 |
Q: I have a 1964 Sunbeam Alpine with a non-syncro transmission. I plan to install a 1967 Alpine ...
A: Ya, you come up with some good ones. Well for every ounce that comes off the flywheel several things ...
|
| Sunbeam Alpine clutch | 9/24/2007 |
Q: I have a 1964 Sunbeam Alpine with a non-syncro transmission. I plan to install a 1967 Alpine ...
A: I really don't know the answer to this one except that one would think that the larger diameter ...
|
| 1979 lincoln mrk v | 9/24/2007 |
Q: when put in reverse, the back up lights don't come on unless you move the gearshift lever and hold ...
A: Ron the adjustment on the transmission is for the combination neutral start/back up light switch. ...
|
| 1965 mustang headlight switch | 9/24/2007 |
Q: i have a mustang (1965) it didnt come with the light switch, i cannot find how to connect the switch ...
A: John, sounds like the piece that you are missing is the chrome bezel that locks the switch to the ...
|
| 1967 Impala rear lights not working with headlights | 9/23/2007 |
Q: I have a 1967 Impala Fastback. When I turn on the headlights my rear lights dont come on, and if i ...
A: Phillip, the first thing that I would check is the ground connections for the rear lights. That ...
|
| Sunbeam Alpine clutch | 9/23/2007 |
Q: I have a 1964 Sunbeam Alpine with a non-syncro transmission. I plan to install a 1967 Alpine ...
A: AJ, the last time that I answered a question like this I got a feedback rating that I was a moron. ...
|
| Fuel Ododr 1966 Rambler (corrected email address) | 9/22/2007 |
Q: I have a 1966 Rambler Classic 770 4-door sedan. It has a 232 engine. There is a fuel odor in the ...
A: I am going way out on a limb on this one, but it seams to me that most of the older cars pre ...
|
| 1966 mustang 3 speed transmission | 9/21/2007 |
Q: my 1966 mustang is stuck in second gear and I can't get it out, can you help me. I took it out for a ...
A: The shift forks are out of alignment. Jack the car up from the drivers side and make sure that it is ...
|
| Installing turn signals in 49 ford | 9/21/2007 |
Q: I have a 49 Ford Custom Tudor and am trying to install a turn signal kit. Trouble is I keep blowing ...
A: Gary, none of the wires from the flasher goes directly to ground. The flasher is a series circuit ...
|
| electrical on Olds | 9/20/2007 |
Q: 70 Olds delta 88. I have redone the cooling system since I had the A/C now working, seems to have ...
A: Kevin, if my memory serves me right the coolant temperature switch on your car is a single wire ...
|
| 1968 corvette | 9/20/2007 |
Q: My husband & I have a 1968 corvette, 327. Just a driver, no shows. We are trying to do some repair ...
A: Jacki, that depends on how may thumbs you have and the equipment in your garage. The thumb this is ...
|
| 1919 cars | 9/20/2007 |
Q: I'm writing a story that involves three women who have slid down a hill on a road covered in sleet ...
A: As late as the mid 1950's we were still using alky as antifreeze. My dad used to purchase the stuff ...
|
| ford mustang | 9/20/2007 |
Q: i bought 67 mustang with a 6 cyl.eng. that will not turn over what would be the best way to tell if ...
A: The only sure way is to take transmission out of the car. This can be a bit of a problem as you ...
|
| cone clutch | 9/19/2007 |
Q: Brad: What a great service! My question is this: I have a 1915 Buick C37 and I', attempting to ...
A: Boy Mike I hate to cry uncle, but on this one you have me stumped. My guess that the pilot bearing ...
|
| back seat | 9/18/2007 |
Q: how do you remove back seat of a 1965 eldorado convertible
A: If I remember right the rear seat cushion is removed by pushing the bottom towards the rear of the ...
|
| 1962 Ford T-Bird | 9/18/2007 |
Q: Our car has a 390 engine & the oil sending unit is leaking. We purchased an oil sending unit, but ...
A: Allen, if I remember right the oil pressure sender on this rig is mounted just above the oil filter. ...
|
| 1951 GMC Chevy Pickup Truck | 9/17/2007 |
Q: Could you tell me the valve lash adjustment for a 1951, straight inline, overhead valve, 6 cly, ...
A: Chevrolet valves have always be .006" for the intake when the engine was hot and .013" for the ...
|
| 38 packard starting problem | 9/17/2007 |
Q: I have a 1938 Packard 6 cylinder with a 6 volt positive ground system. The engine has been ...
A: Well Earl,he first thing that I would to be sure that the engine is not fitted super tight or that ...
|
| 1970 ford fairline | 9/16/2007 |
Q: would like to know the firing order its a 302 V8 engine
A: The firing order is 1-5-4-2-6-3-7-8. Number one cylinder is on the passengers side of the engine and ...
|
| Oil Pump Question | 9/16/2007 |
Q: I have a 72 Chevy C-10 LWB, and I just recently started to put it back together. One of the major ...
A: Paul, here is what I would due in this case. From what you say I assume that this is a V-8. On that ...
|
| starting problems | 9/16/2007 |
Q: i have a 1974 oldsmobile omega v8 when i turn the key the car does nothing and i can see my volt ...
A: When this car was new there was a metal heat shield around the wires. If there is a bone yard around ...
|
| 69 camaro 4 speed clutch problem | 9/16/2007 |
Q: this morning i took my camaro out, about a mile from the house i noticed the clutch pedal was laying ...
A: There is an adjustment on the rod that connects to the clutch fork, the arm that sticks out of the ...
|
| starting problems | 9/15/2007 |
Q: i have a 1974 oldsmobile omega v8 when i turn the key the car does nothing and i can see my volt ...
A: The ignition coil circuit on any 12 volt car with ignition points and some of the early electronic ...
|
| 69 camaro 4 speed clutch problem | 9/15/2007 |
Q: this morning i took my camaro out, about a mile from the house i noticed the clutch pedal was laying ...
A: Danny, I guess that the first thing to do is stick your head up under the dash and make sure that ...
|
| Body rubber retainers | 9/14/2007 |
Q: I have a 70 olds, and am looking for the small T plastic clips that attach the rear compartment ...
A: Kevin: The best advice that I can give you is to dive into a copy of Hemmings Motor News, the ...
|
| 67 deville tranny leak | 9/14/2007 |
Q: Subject Transmission Leak (Ipreviously asked Dick this question and I have a follow up to his ...
A: I am going way out on a limb on this one. But I have been told by folks over the last 3/4s of a ...
|
| starting problems | 9/14/2007 |
Q: i have a 1974 oldsmobile omega v8 when i turn the key the car does nothing and i can see my volt ...
A: If the voltage gage drops to zero when you try to start the engine it sounds like a defective ...
|
| starting problems | 9/14/2007 |
Q: i have 1974 oldsmobile omega v8 5.7L thats not getting current to the starter i took the starter to ...
A: If the voltage gage drops to zero when you try to start the engine it sounds like a defective ...
|
| 1965 Mustang windsheild wipers | 9/14/2007 |
Q: When i pulled out the heater box and motor my windsheild wipers stopped working. I hooked up the ...
A: I seam to remember that the ground wire for the wipers was attached to the same bolt as the heater. ...
|
| 1948 Packard Convertible | 9/13/2007 |
Q: I just bought above vehicle, it had been hit in the rear, and the repair was very poor. I intend to ...
A: Dick, I am not aware that Packard built a notchback coupe in 48. Convertibles are built like a ...
|
| 1965 Mustang Handling | 9/12/2007 |
Q: When I accelerate car pulls to the right, like it wants to change lanes, when I let off it wants to ...
A: John, sounds like you might have broken a center bolt on one of the rear springs. This would allow ...
|
| 70 Camaro headlight problem | 9/12/2007 |
Q: When I bought the Camaro, the headlights seamed to work ok. As time went on I found that when the ...
A: Ron, I would suggest that you check the amperage draw of the headlights. Some of the newer high ...
|
| A833 Reverse light switch 70 swinger | 9/12/2007 |
Q: I've replaced the reverse light switch in my trans. after installing the new switch, it appears that ...
A: At this point in time I think that at least the transmission pan needs to come off so that you can ...
|
| IDILING PROBLEMS | 9/9/2007 |
Q: I OWN A 1970 CORVETTE 350 300HP. AFTER DRIVING ON THE HIGHWAY OR ON A LONG DRIVE WITHOUT STOPPING ...
A: Jimmy, it sounds like a carburetion problem in the making. If it were a later model car with a lock ...
|
| 1967 Lincoln Continental 462 | 9/6/2007 |
Q: I have a 1967 continental 462 and would like to know what is the the firing order of the spark plugs ...
A: The firing order is 15426378. There should be a #1 on the distributor cap indicating that should be ...
|
| missing at any speed | 9/5/2007 |
Q: I have a 312 in a 57 t-bird. I have replaced the sparkplugs, sparkplug wires, points, dis.cap, ...
A: You are running a 312 V8 getting 25 miles per gallon and think of changing to an RV cam for more ...
|
| 68 ply valiant 273 motor | 9/4/2007 |
Q: I just rebuilt the motor for my 68 Ply Valiant Signet. I bought a rebuilt Carter 2bbl carburetor to ...
A: Yep, it tells me that the car was originally equipped with a solenoid switching device the routed ...
|
| 1953 Ford Customline | 9/2/2007 |
Q: How much work is there to switching a 6 volt to a 12 volt? A friend told me there are kits for ...
A: Rene, my question is quit simple. Why do you want to switch to 12 volts? A good 6 volt system in ...
|
| Thermostatic vacuum switch | 9/1/2007 |
Q: 1970 Olds delta 88 455. How can I tell if the thermostatic vacuum switch is operational, and if so, ...
A: Kevin, the thermostatic vacuum switch that you have is an attempt by the car makers to meet ...
|
| brake drums | 9/1/2007 |
Q: Brad, I have a 1935 dodge touring sedan, The car has not been driven for a couple of years.Looking ...
A: Steve, ya gotta get rough with these drums. I hope that you are using one of the real heavy duty ...
|
| antenna mech. replacement | 9/1/2007 |
Q: On a 68 GTO how do you replace the complete antenna mechanism from antenna to radio ANSWER: Is it a ...
A: Just the back of the fender if loosened will pull away far enough to get the unit in and out. The ...
|
| Gas still in oil after fuel pump change | 8/31/2007 |
Q: you answered a question about gas in the oil pan on my '67 Mustang. Well I went and changed the ...
A: Dave, my experience is that if the carburetor is the cause of fuel getting by the rings and into the ...
|
| 1980 Pontiac Trans AM | 8/31/2007 |
Q: Where can I find the factory measurments for the rear end in a 1980 TA. example: pinion offset, ...
A: John, I usually go to the dealership and ask the service manager if I can look at a manual for a few ...
|
| antenna mech. replacement | 8/31/2007 |
Q: On a 68 GTO how do you replace the complete antenna mechanism from antenna to radio ANSWER: Is it a ...
A: Kevin, here is how I remove that damned sealant from paint. Start at one end of it and using your ...
|
| 1966 Corvette electrical problem | 8/30/2007 |
Q: I have a 66 vette, driver with a crate 350. The other day I was driving it, and 15 minutes into my ...
A: Victor, first I am not a fan of braided hoses under the hood of the car as they are conductive and ...
|
| 1953 Ford Customline | 8/30/2007 |
Q: 239 ford flathead, rebuilt generator, brand new voltage regulator, Why would the cut out relay ...
A: Rene, generators only charge well as the engine speed increases. The current cut out relay, as the ...
|
| Adding a power brake booster | 8/29/2007 |
Q: I recently added a power brake booster to my 63 Studebaker Lark (all drum)brake system. The booster ...
A: Goodmorning Brian: One of the few modifications that I like when dealing with old cars is updating ...
|
| overheating | 8/29/2007 |
Q: i have a 1974 oldsmobile omega with a v8 5.7L and in low temp weather it runs great but in the heat ...
A: Dyron, I'm afraid that if it was anything else it would overheat regardless of outside temperature. ...
|
| 1965 Mustang neutral safety switch | 8/28/2007 |
Q: I'm having intermittent starting problems (as if the transmission is not in park) on my 1965 Mustang ...
A: Bruce, if my memory serves me right the safety switch is located on the side of the transmission on ...
|
| Engine oil for my 1951 GMC pickup | 8/28/2007 |
Q: I have just gotten a 1951 GMC pickup with the original 208 6 cyl. engine. It has unknown mileage ...
A: John, this is like asking which is better, chocolate or vanilla. If the engine is running well and ...
|
| 1949 Nash 600 | 8/28/2007 |
Q: A friend needs to remove the fuel gauge from his '49 Nash. Its in a pod that has no obvious way of ...
A: Dale, there was a time when I was younger and thinner that I used to be able to lay on the front ...
|
| Overheating | 8/28/2007 |
Q: I have a 1978 Chevy Impala and lately it's been running hot. I changed out the temperature sensor ...
A: Renard, a little more information would help here. Is the car running hot when it is idling or when ...
|
| MGB | 8/27/2007 |
Q: I need to know the proper amount of travel on a 1980MGB clutch slave cylinder. I am getting less ...
A: John, the right answer is 1 to 1 1/4 inches of free travel at the clutch pedal. Less than a quarter ...
|
| 1929 Model A speedometer | 8/27/2007 |
Q: In my 29 Model A an oval Stewart Warner speedometer is installed in the dash. It stopped working, I ...
A: Ed, it appears one of two problems. First someone may have at one time or another replaced the inner ...
|
| 86 camaro motor conversion | 8/27/2007 |
Q: i recently wrecked my 83 chevy C20 that has a new 350 4 bolt and i want to drop that into my 86 ...
A: Jason, if you are using the computer and electronic controls make sure that the computer matches the ...
|
| 1957 won't start | 8/26/2007 |
Q: I have a 1957 mercury montery. It will not turn over, but yet the battery is charged according to my ...
A: Joe, make sure that the engine is not stuck. A breaker bar and socket on the front pulley will check ...
|
| 1964 1/2 Mustang | 8/26/2007 |
Q: My 1964 1/2 Mustang runs great when you first start out with it, however once you run it for 30 ...
A: Aurelia, make sure that there is a bonding strap (ground cable) between the body and the engine. ...
|
| let there be light... | 8/26/2007 |
Q: i have a 57' chevy 4 door. none of the dash lights go on except for the turn signal indicators, and ...
A: Jay Leno has been away from turning wrenches so long... If the directional signal indicator lights ...
|
| Brake System | 8/26/2007 |
Q: I recently replaced the master cylinder and booster on my 69 camaro with a chrome master cylinder. ...
A: Alberto, you have fallen into a trap that all of us have fallen for one time or another. Assumed ...
|
| 1953 Ford marathon information | 8/25/2007 |
Q: My dad has a 1953 Ford Marathon 4 door car with a flathead 6 cylinder motor in it. It probably needs ...
A: Brenda, I would check the web site for the National Auto Dealers Association www.nada.com. They have ...
|
| Older Ford repair tools. | 8/25/2007 |
Q: I recently purchased a 1954 Ford truck shop repair manual. I noticed in the repair illustrations ...
A: Roger, this is a tough one. Most of these tools were in the dealer required list and the dealers ...
|
| Fuel in Oil Pan | 8/24/2007 |
Q: I have a '67 Mustang and it's getting gas into the Oil pan. I just had the carb 'rebuilt' and ...
A: Dave, the bottom of the fuel pump diaphragm drains right into the oil pan. This used to be a real ...
|
| 1928 Chrysler R 9480 | 8/24/2007 |
Q: How do I take the rear wheels of so that I can grease the bearings? The key seems to be in real ...
A: John, my dad taught me to use a tool that he called a bingo cap. It was a solid piece of round stock ...
|
| leak near driver side kick panels | 8/24/2007 |
Q: Anyone know where to start looking for a leak that dampens my carpet after a rain. I have a 1974 ...
A: The most common place to look on this car is the main wiring connection that comes through the fire ...
|
| 68 ply valiant 273 motor | 8/24/2007 |
Q: I just rebuilt the motor for my 68 Ply Valiant Signet. I bought a rebuilt Carter 2bbl carburetor to ...
A: 1968 cars were whole new breed of performance problems for the mechanic. It was the first year of ...
|
| brake fluid reservoir | 8/23/2007 |
Q: I have a 51 Buick Riviera and can't seem to find the brake fluid reservoir. Can you help. Thanks
A: Gary, they hid it on you. Ok, Pull up the floor mat from the drivers side. There should be a rubber ...
|
| Adding a power brake booster | 8/23/2007 |
Q: I recently added a power brake booster to my 63 Studebaker Lark (all drum)brake system. The booster ...
A: Boy you guys out there sure come up with problems that make the old gray matter steam a little. Ok, ...
|
| Steering shaft removal 1970 Buick Skylark - GM A Body | 8/22/2007 |
Q: I need to remove and the re-install the steering shaft on my 1970 Buick Skylark. There seems to be ...
A: Craig, you are describing the joint in the shaft that allows the shaft to collapse on a frontal ...
|
| 1981 Corvette motor repair | 8/22/2007 |
Q: I just bought a 1981 Vette. I drove it home and the motor is now making a loud noise when out of ...
A: Dee, is the noise speed sensitive? Does it speed up as the engine speed increases? If it does the ...
|
| Old Headlights | 8/22/2007 |
Q: I have found a set of old dual(single filament bulbs)chrome headlight housings in a barn that I ...
A: This one is out of my field but if I were faced with this situation, which could be very good for ...
|
| HORN PROBLEMS ON 1962 T-BIRD | 8/22/2007 |
Q: when i depress the horn ring the horns sometimes wont shut off. Also when i turn the turn signal ...
A: There is a product on the market called Liquid Tape. It is sold in most parts stores and is a room ...
|
| battery dies | 8/21/2007 |
Q: I thought I had my 64 Pontiac Laurentian 230 6 cyl working. I installed a new battery and it ran ...
A: A lot of guys with old cars use a device that attaches to the battery cable that disconnects the ...
|
| 1955 chevy p/u | 8/21/2007 |
Q: I have a 55 chevy pu that's been restored. They put a 350 engine in it with automatic transmission. ...
A: Ronnie, one thing that I should have mention before is to make sure that the wire between the dash ...
|
| 1965 1/2 stingray convertible corvette | 8/21/2007 |
Q: My Dad recently passed away and in his garage is the car mentioned above. I am trying to determine ...
A: Michele, numbers matching means that code numbers stamped on the transmission, engine, and ...
|
| SB Chevy 350/turbo 400 into '48 Pontiac | 8/21/2007 |
Q: Can I? and how hard will it be to find motor mounts etc? I would like to try to do this without ...
A: RC, you are in for a fabrication project. It is not a question of finding motor mounts it is a ...
|
| service light | 8/21/2007 |
Q: my service light has been coming on, and i have taken it to the shop,and know whats wrong, but cant ...
A: David you have not given me enough information to answer this question. If you know what the problem ...
|
| HORN PROBLEMS ON 1962 T-BIRD | 8/20/2007 |
Q: when i depress the horn ring the horns sometimes wont shut off. Also when i turn the turn signal ...
A: Larry, I do not think that you have to remove the PDR face plate. I think that once the steering ...
|
| tail pipe smoke | 8/20/2007 |
Q: "I have a 1957 Bel Air 2 dr hardtop with a 60 corvette 283 engine (i think, I have not done the ...
A: Richard if the engine has any age on it the chances that the valve seals are leaking by are better ...
|
| 1955 chevy p/u | 8/20/2007 |
Q: I have a 55 chevy pu that's been restored. They put a 350 engine in it with automatic transmission. ...
A: Ok, lets try to sort this one out. I believe that the 55 Chevy pick up was originally a 6 volt ...
|
| Power Steering/91 Edlorado 4.9 litre engine | 8/19/2007 |
Q: I have a 91 Caddy Eldorado. I just replace a leaking power steering pump. However, everytime I turn ...
A: Jeff, it is time for your mechanic to reach in his tool box and grab his trusty stethoscope. Probe ...
|
| Chinese finger | 8/19/2007 |
Q: I need a chinese finger for some repairs on my car and I was wondering if you know where I could get ...
A: John, the package on the Chinese finger in my tool box, which is over 30 years old, reads rear main ...
|
| 1967 Starter Problem | 8/19/2007 |
Q: I have a 1967 SS Camaro Big Block 396 Motor the Headers are real Close to my starter and Yesterday I ...
A: Jon, there is a high torque starter available for this engine. Also when this car was built the ...
|
| overdrive transmission | 8/19/2007 |
Q: I have a 53 ford pickup with a 3 speed trans. I would like to install a 3speed overdrive trans. I ...
A: Wayne, if my old head is working right 49 through 53 Ford, Lincoln, or Mercury will fit very nicely. ...
|
| 350 SBC | 8/17/2007 |
Q: I have a 350 sbc that was purchased in a lot with a street rod project. I have sold the other items ...
A: Jeremy, I have the books back in my office that will decode this, the problem is that I am 2,000 ...
|
| 1969 Camaro Starting problem | 8/17/2007 |
Q: Just bought a 69 Camaro 350. New battery, absolutely nothing on ignition? Lights won't come on, no ...
A: Tim, it sounds like a bad connection somewhere or a dead new battery. I hope that you have a ...
|
| fuel pump | 8/16/2007 |
Q: How do you repair a 1954 chevy fuel pump - 235 engine? Any help will be appreciated. Thanks, CB HArt
A: The best advice that I can give you is be careful. The pump is located on the side of the engine ...
|
| electrical | 8/15/2007 |
Q: I have a 1968 cutlass that has an intermittent electrical condition. when I turn the lights on, it ...
A: Dave, right away my mind clicks right over to the ground side of the electrical system. On that car ...
|
| resonator | 8/15/2007 |
Q: I have a 70 olds with a muffler and resonator, is that thing really have a purpose, is it necessary? ...
A: Kevin, the resonator is just what the name applies, to control resonance. The resonator has no ...
|
| vacume wipers | 7/26/2007 |
Q: on my 55 ford 272v8 what does the thing in front of the manifold that has a heater hose and vacume ...
A: If my old memory serves me correctly that is the temperature control for your heater. That vacuum ...
|
| 86 jaguar xj6 4.2 s 6 | 7/26/2007 |
Q: my car starts up, but put her in drive she stalls. after a good time of trying like starting in ...
A: Wow, in the age of electronics there could be so many things acting up. Here is the list that could ...
|
| 72 mustang | 7/25/2007 |
Q: I am installing a new universal washer bottle to my mustang and I was wonder which wires to connect ...
A: Did this car not have washers installed in it before? If so the wire should be right there in the ...
|
| 1941 vacuum shift | 7/25/2007 |
Q: i have a customer with a 41 chevy with the vacuum shift. the problem is it won't stay in reverse. i ...
A: These vacuum shifters worked real well when they worked and were a real pain in the sitter when they ...
|
| 57 ford tbird 312 engine. | 7/25/2007 |
Q: The vehicle was in storage for 12 years. It has a holly 4bbl carb. I cleaned the carb as there was ...
A: I am sorry for the delay in this reply. The Holley Carburetor that you have uses different float ...
|
| 79 Corvette Steering wheel | 7/25/2007 |
Q: Brad, I'am replacing my steering wheel (telescopic tilt). Needs new leather ! How do I go about ...
A: Been a while since I worked on one of these. Check the underside of the steering wheel. It is common ...
|
| 1980 MGB Engine Earth Strap | 7/24/2007 |
Q: I am in the process of reinstalling a rebuilt engine and transmission in my 1980 MGB LE. When I ...
A: Unless you are doing this car as a 100 point, the experts will be crawling all over the car ...
|
| Starting Problem | 7/24/2007 |
Q: I own a 1948 ford coupe with it's original flat head v8 engine (It was completely rebuilt many years ...
A: The figures for maximum turning torque on an eight cylinder engine that I have always used is 40 ...
|
| leaking seal in power steering unit on 1972 monte carlo | 7/23/2007 |
Q: how do you get to the seal to replace it am surem it is the seal
A: I need a little more information to help solve this one. There are three seals in the system that ...
|
| delco remy horns | 7/23/2007 |
Q: have two horns : delco remy #'s 1951095 and 1951086 what cars are they off of. Found in dads garage ...
A: This one is a bit out of my realm, but I think that I would take the part numbers down to my local ...
|
| BRAKE DRAG ON 1976 FIREBIRD | 7/23/2007 |
Q: WHAT WOULD MAKE MY FRONT BRAKES DRAG BUT STILL WORK AND NOT LOCK UP? WE'VE CHANGED THE CALIPERS, ...
A: First of all how are you determine that the brakes are dragging? Disc brakes do not retract as ...
|
| Mid Frame to Rear Brake Line 1956 Thunderbird | 7/23/2007 |
Q: I am replacing the brake lines and have a pre-formed steel line from CASCO--how do I get the line ...
A: The short answer is, you don't. The brake and fuel lines are installed at the factory before the ...
|
| 1966 chevelle malibu convertible | 7/22/2007 |
Q: I am trying to get an idea about how much to sell my car for, it is an 1966 chevelle malibu ...
A: When I once worked in a car dealership way back in the time machine, the sales department claimed ...
|
| 1948 Packard brake system | 7/21/2007 |
Q: I have a 1948 Packard 2292. some years ago I put in some incorrect brake fluid (airplane type) and ...
A: If the car has been stored for 15 years there is a good chance that there has been some condensation ...
|
| 57 ford tbird 312 engine. | 7/21/2007 |
Q: The vehicle was in storage for 12 years. It has a holly 4bbl carb. I cleaned the carb as there was ...
A: David, I forgot one thing. There is a tube that runs through the heated section of the intake ...
|
| 1962 ford galazie convertibile | 7/20/2007 |
Q: A tree fell during a storm on top of my car. It broke my convertible frame. Can this be repaired. ...
A: Anything can be repaired or rebuilt, that is not really the question. The question is how much will ...
|
