Expert: John Newman - 12/26/2010

Question
We just received a Ridgeway Grandfather Clock. The approx. age is about 30+ years old. The clock does not keep operating, but stops ticking. When it does operate the "tick,tock" is not evenly timed.
I assume that it most likely needs to be cleaned and adjusted, but how do I go about it.
Any help would be greatly appreciated.

Clock information.
           Ridgeway and Tempus Fugit on the clock face,

 Movement is, "o" Movement, 8 Day-Key Wind-5 Rod Westminster Chimes. stamped with;   Graveley Furn. Co. Inc.      
                       Martinsville, Va. USA
                       Made In Germany
                       No (0) Jewels
                       Unadjusted
                       PL 65 cm
                       349322

Answer
Don, it could very well need cleaning, but if the beat is uneven, that could be the main problem.

Ridgeway was part of Gravely and then became a part of Pulaski Furniture and finally bought out by Howard Miller.  With the PL 65cm, the movement could have been manufactured by Jauch, but I'm not sure right now.  It is rather rare to see a key wind grandfather floor clock, but there were some made.  I am going to include the steps for determining why a clock is not running.  Check these things out and if it doesn't resolve the problem, get back with me.



THE FIRST LEVEL IS THE SETUP.  

For Floor Clocks   If the clock is in operating condition but not working, I would check the stability of the clock in that it doesn't rock or wobble on the floor.  It should be relatively level.  The level is not critical, as setting the beat (below) will correct for this.  

Next, verify that the weights are hung correctly.  On most clocks the weights vary in weight.  The general rule is that if two weights are equal, the third weight, if it is heavier, goes on the right side (as you face the clock).  If the third weight is lighter, it goes on the left.

Is the pendulum hanging configuration correct?  This means that the suspension spring, hanger, verge and pendulum are all connected properly with nothing broken, especially the suspension spring.  When the pendulum swings, it should be "in beat", meaning that when the pendulum swings you hear an even tick....tock....tick....tock.  If it is uneven, like tick..tock......tick..tock, the clock will probably stop.  Most later model movements have an "auto-beat" mechanism.  The beat can be set by holding the pendulum over to one side next to the case and releasing it.  It will automatically correct itself.  If it does not have this feature, the escapement crutch will have to be slipped manually.  If required, I would need a good description of the verge and hanger mechanism or a photo of the back of the movement to give you instructions for that.  Also check to see if the hands are catching on each other or the dial.  Look at the chime and strike hammers to see if they are all in alignment at the rest position.  Sometimes jammed hammers or the drive mechanisms will stall the clock.

For Mantle or Wall Clocks   The clock should be stable and not wobble or rock.  There should be an even beat.  If not, wall clocks can be set in beat by moving the bottom of the clock to one side or the other.  Some wall clocks have the auto-beat adjustment.  Mantle clocks can be shimmed up on one side or the other to obtain an even beat.  These methods work if the beat is not off too much.  If the out-of-beat condition of these clocks are excessive, other adjustments have to be made.


THE SECOND LEVEL INCLUDES MAINTENANCE

Usually, the first symptom of a clock failing is that the chime and/or strike mechanisms slow down and then fail altogether.  At this point the clock needs to be serviced.  This includes cleaning, inspecting, oiling and adjusting.  In the inspection, the movement is checked for adjustments, broken or worn parts.  If there are any broken or worn parts, we go to the third level. If all parts are okay, a good clock oil and grease is used.  In most cases the movement should be removed from the case to have access to all the lubrication points.  Clock lubricants can be bought from clock suppliers.  Using lubricants for other applications can cause problems, as some lubricants are not compatible with others.  This even applies to different clock oils.  After lubricating, the operation is checked for final adjustments.  I recommend maintenance be performed every 7 to 10 years.


THE THIRD LEVEL IS REPAIR.

This requires that the movement be broken down and all parts inspected and repaired or replaced, and then reassembled lubricated, adjusted and tested.  I do not recommend this except by an experienced clockmaker.



John Newman
THE VILLAGE CLOCKSMITH
Old Prattvillage
Prattville, Alabama