About Dr. Ari Roark Expertise Metalsmithing, Goldsmithing,Jewelry Making, Gemology,Metallurgy,Art Jewelry,Jewelry Appraising,Metal Mill Work,Jewelry Education,Group Projects Adaptable to Special Populations as well as ordinary groups,Ethnobotany,Metal Clays, International Jewellery Law,Trade Law,Rock hounding,Industrial Health and Safety Assessment and Education as it pertains to Jewelry Studios (of all sizes and manufacturing concerns relative to the Trade, Jewellery Trade Organisations,Objective US Jewelry School critical Analysis,Applied Anthropology,goldssmithing,lapidary,metals,refining
Experience More than 35 years experience in the Jewelry Industry, Juris doctorates, PhD's in Anthropology, Cultural History, Cultural Geography, Mining Locations Assessments, Industrial Health and Safety Inspector to the Jewelry Industry, Montessori Educator, Occupational Therapy, Natural Historian, Scholar of Jewelry Evolution, PhD in Creativity ( the analysis of the divergent genres of thought on the process and impetus of the essence of creativity as a state of being expressed tangibly),Extensive Fieldwork with populations of Traditional craftsmen worldwide, former Peace Corps volunteer, Former VISTA volunteer, Etc.
Organizations too numerous to list
Publications prefer not to answer for reasons related to plagiarism
Education/Credentials PhD Anthropology( Applied(1), Cultural(2)Ethnobotany(1),PhD -Physics (Metallurgy 1)( Wave and Particle Dynamics 1),,JD,MD,MFA-Metals/Jewelry,,MFA-Printmaking, MFA-Sculpture, Extensive undergraduate degrees, extensive post doctoral work, Montessori Educator Certification (Primary and Secondary)..many, many Degrees, Grants, and Awards in my past as an Academic turned Jeweler, OSHA Certifications
Awards and Honors too numerous to list including 3 Honorary Doctorates, Two Humanitarian Related Awards, and Service on Many Boards of Directors
Jewelry Making - putting gemstones into pickling solution and supersonic
Expert: Dr. Ari Roark - 6/23/2009
Question I am attaching gemstone beads using wire and torch and would like to know how you recommend removing oxidization and flux after the stone is attached. I have put stones into the pickling solution in the past and they have been OK but I also know one is not supposed to expose gems to that sort of thing. I would appreciate any advice you have.
On the same note - how safe is it to put attached gemstones into supersonic after polishing?
Answer Hello Karina,
First make the component then pickle then attach the gemstones by looping the wire, etc. That way the metal is cleaned before the gem component is finished- a final polish is all that may be necessary and you can do that before attaching the gemstone as well.
Many gemstones cannot be put into an ultrasonic cleaner, but can tolerate steam. After polishing you should not need to clean if the polishing is done correctly- but use a water soluble compound if you must clean after polishing so that hot tap water and its force will do the job. Ultrasonics - particularly cheapies ,like connoisseur's brand available at most x-marts are junk: they use a cleaning solution that will oxidize your silver on contact requiring you to repeat all the finishing again. Steam is better unless you are using emeralds, kyanite, and other soft stones that steam may adversely affect too.
More often than not if the gem is a decent quality the pickle solution will not affect it- but always neutralize it with soda crystals and water then rinse well after removing any piece from the pickle and don't let it get above 140 degrees and you should be fine with all but precious stones that are soft or pearls, turquoise and assembled gem-like stones like opal triplets, doublets, etc.You should make sure that the stones do not contain iron though: a stone like specular hematite or a rough iron containing crystal will contaminate the pickle the same way introducing something ferrous will. So know your materials and their hardness and then think through the construction before beginning to assemble the components to minimize time and effort and re-doing processes that could have been finished before the assembly begins.
Hope this is what you needed to know
Best regards,Ari
