AllExperts > Mazda Repair 
Search      
Mazda Repair
Volunteer
Answers to thousands of questions
 Home · More Mazda Repair Questions · Answer Library  · Encyclopedia ·
More Mazda Repair Answers
Question Library

Ask a question about Mazda Repair
Volunteer
Experts of the Month
Expert Login

Awards

About Us
Tell friends
Link to Us
Disclaimer

 
 
 
 
About Mp2
Expertise
I prefer to answer questions relating to the Miata since this has been my area of specific expertise since 1991. I can answer questions relating to the other Mazda models however some limitation of expertise may reduce my accuracy.

Experience
Mazda technician since 1987, shop owner and specialty are regarding the Miata since 1991 covering mechanical, electrical, trim and body. Specializing specifically in drivability concerns.GKHS 1985, BVC 1987, MNA 1989, ASE Master Technician Mechanical 1995, ASE Master Body/Paint/Collision 1996


Education/Credentials
GKHS 1985, BVC 1987, MNA 1989, ASE Master Technician Mechanical 1995, ASE Master Body/Paint/Collision 1996

 
   

You are here:  Experts > Home/Garden > Auto Repair > Mazda Repair > speedo

Mazda Repair - speedo


Expert: Mp2 - 8/13/2009

Question
QUESTION: how do you remove the gauge cluster in a 2007 miata. also how do you remove the hood above the cluster?

ANSWER: To get the instrument cluster out you need to remove the lower cowl (pull out and disconnect the upper retaining clips then unhook it from the bottom.  To remove the meter hood pull upward on the meter hood and detach the four expansion clips located at the clock positions 9 o'clock, 11, 1 and 6.  It's easy to break a meter hood so patience is a must with firm yet gentle persuasion.  

Now the instrument cluster is another animal all together.  To disconnect it and replace it requires it to be configured before removal.  If it's not configured before you will get a system malfunction upon reassembly (only done with a Mazda MDS).  If you remove it and are replacing the same one you MUST disconnect the battery and drain all reserve power from the system if not you could run the risk that the system will not recognize the the cluster and a system malfunction may occur requiring a reprogram with a Mazda MDS.  (not cheap)

To physically remove it,  you have two screws underneath and one at 12 o'clock in the back.  Two connectors and two clips.  It must be rotated up and out from the bottom of the display to remove it.  There is a harness clip in the center rear of the cluster that must be rotated 90 degrees (CCR) to release the assembly once clear of the dash.

There you asked, I answered.  Good luck.

You keep popping up with questions, if I'm going to keep educating you on the same third generation Miata your going to have to contribute to the cause or risk getting cut off.  AllExperts does not provide this tech with any sort of income you know.

service@miatashop.com

---------- FOLLOW-UP ----------

QUESTION: whats the difference how many ques i ask? if its not my question it will be somebody elses. do you think im asking to get a monetary gain? i just bought the car 3 months ago and little by little im making very subtle changes. your the expert so who better to ask. if a little contribution every now and then will make your cause happy give me a figure; im no cheapo.

Answer
That was meant in a jovial way.  I help dozens of Miatafiles everyday so your cause is no different, I only recognized you as a repeat questioner.  Just remember us from time to time when the buying starts, helps us afford the ability to stay on the help line.

service@miatashop.com

Add to this Answer   Ask a Question


 
User Agreement | Privacy Policy | Kids' Privacy Policy | Help
Copyright  © 2008 About, Inc. AllExperts, AllExperts.com, and About.com are registered trademarks of About, Inc. All rights reserved.