| Subject | Date Asked |
|
| carrier in MS | 8/7/2009 |
Q: just happened to visit your profile while randomly searching on a google. i have finished my B.E ...
A: Of course. You can pursue your studying in MS of mechanical engineering and take your courses ...
|
| Mechanical Engineer | 6/22/2009 |
Q: What is the best part about your job?
A: It depends on many factors like the person's interestings. I can not say a general answer or in fact ...
|
| high schol project | 5/5/2009 |
Q: What are your job duties?
A: Mechanical engineering is the most comprehensive field of engineering. We work in automotive, ...
|
| question | 5/3/2009 |
Q: I m electronics and communication engineer , interested in industrial engineer and career there is ...
A: I highly advice you to take this course. It will be needed for you in your professional ...
|
| query about automobile engineering | 8/24/2008 |
Q: I'm a student from Nepal. I'm interested in automobiles and want to seek my future in it. Please ...
A: Automobile engineering is a field of engineering that deal with automobile parts such as ...
|
| E-mail Interview | 4/23/2008 |
Q: my name is Alex and I am a senior at Niceville High in Florida. I'm writing a career exploration ...
A: I am a MsC, student in Tabriz university and all of may answers in based on it. 1- usually studying ...
|
| question | 4/14/2008 |
Q: I want to know variation of transverse and normal stress in an assumed section of a beam under an ...
A: Variation of normal stress in this condition is linear from zero to a max value. Its zero value is ...
|
| mechanic | 4/6/2008 |
Q: I am looking for some information about robot manipulator degrees of freedom. Can you help me ...
A: Grubler's well known formula is used for this purpose extensively. F=6(l-n-1)+S(fi) F is degree of ...
|
| phase diagram | 3/2/2008 |
Q: I'm a first year student mechanical engineering in Holland. I would like to find some more ...
A: Phase diagram is a method that you can obviously see the percentage of existence any element of ...
|
| If you would please answer these questions i would be very thankful | 3/1/2008 |
Q: 1. do you have a professional engineer license? 2. From what University did you graduate from? 3. ...
A: in lines below I answer your questions: 1- yes I have BsC. in mechanical engineering and now I am ...
|
| Intake Manifold Analysis | 3/1/2008 |
Q: I am doing a design project, where i have to design an Intake Manifold for an engine. It is a simple ...
A: you question is very general It depends on your subject of analyze. If you want to analyze velocity ...
|
| drive transmission (shaft and gear fitting) | 2/27/2008 |
Q: im doing this project where i need to select a drive transmission for a pump and motor... ive chosen ...
A: your question has a simple solution. you should prepare a cylinder with 15mm outer radius and 8mm ...
|
| shaft design | 2/20/2008 |
Q: How to construct a Goodman Diagram to estimate fatigue strength for varying mean stresses in a shaft ...
A: for constructing Good man diagram with variation of mean stress you should use from this formula: ...
|
| Engineering | 1/29/2008 |
Q: I wanted to ask you some questions on engineering. Mostly what i wanted to know was how many years ...
A: it will take about 4 years to have a degree in every engineering as well as structural engineering. ...
|
| toppest student | 1/22/2008 |
Q: Masoud Fakhrabadi I am from Iran and find you when i refer to this site about a question. I am a ...
A: Sima, I will be glad if I can do anything to Iranian all over the world. you should improve you ...
|
| Center of Gravity | 12/30/2007 |
Q: How to locate Center of Gravity of machines(e.g. lathe)? Is there any practical method for it?
A: there are several ways to find it. if you are a member of a large company that has heavy machines ...
|
| Strength of Plywood | 12/13/2007 |
Q: Could you tell me how many pounds per sq. inch 3/4" plywood will support? I am replacing wood in ...
A: your question is'nt so that anybody can answer it. because its answer is a number that you can only ...
|
