| Subject | Date Asked |
|
| S & S CARB ADJUST | 11/21/2009 |
Q: How do I adjust the fuel/air mixture? Thanks. sid.
A: Start the bike and let it warm up to temp. Slowly turn the air/fuel mixture screw inward, just until ...
|
| 1976 fxe | 11/19/2009 |
Q: i have an fxe stroked to a 1340 with 4 plugs for better combustion.Whomever owned it last took off ...
A: I am not sure which part you need answered so I will do both. the kicker can be put back on without ...
|
| harley trans. leak | 11/17/2009 |
Q: Hey Mike, had my '95 flh in the shop for a trans. leak(on primary side)-they changed the main shaft ...
A: the seal is on the outside of the main bearing and is pushed against the case and rides on the shaft ...
|
| blow back | 11/17/2009 |
Q: I own a 89 flhtc, 1340 evo. Im experiencing excessive blow back, about a qrt in 100 miles when ...
A: There are two possible reasons for this problem. One is the crank case vent is work and oil is ...
|
| charging system | 11/16/2009 |
Q: i have an 86 flst. i replaced a battery with a bad cell. i put in a brand new battery and rode for ...
A: What you need to test is the stator. Unplug the regulator and at the prongs for the stator, od a ...
|
| FLAT TIRE REPAIR? | 11/16/2009 |
Q: Crap! I took my 1983 Honda CM450E out for a final 30 mile drive before wintering it, because it was ...
A: You would have to have the when taken off and the tire removed as well as the innertube to see what ...
|
| won't start | 11/16/2009 |
Q: Have 07 classic. When I go to start it sometimes it will not start. when push start button nothing. ...
A: When you try it start it and it doesnt start, check at the coil with a test light. Do you have power ...
|
| Evo Flywheels and rods | 11/15/2009 |
Q: I have a 1977 Harley FLH that I am rebuilding, a freind told me to put Evolution flywheels and rods ...
A: Doing that would change the stroke. the 77 flywheels have 3.96875 stroke and the EVO has 4.250. So ...
|
| bleeding brakes on harley | 11/15/2009 |
Q: We have a 94 harley dresser and cannot bleed the front brakes and the manuel sucks.
A: Make sure you have brake fluid in the master cylinder and while bleeding dont let it go dry. Pump ...
|
| brake light | 11/14/2009 |
Q: 1985 Electra glide and my brake light is staying on all the time
A: Check your front brake. Where the controls are you will see that there are two brackets. One holds ...
|
| 88 1200 sportster | 11/13/2009 |
Q: Iwant to put a wide glide on my bike .I already have the fork and triple tree mfg. by showa it has ...
A: As long as the triple trees are made for your bike you should have no problems. Just installt he ...
|
| 85 ignition | 11/12/2009 |
Q: I have 2 85 evos. An Fxrs, and an Fxrt. The rs has an s and s with the voes removed completely and ...
A: If you have no power at the coil, then you have a wiring problem. On the hot side of the coil you ...
|
| "Stabil" in gas tank? | 11/11/2009 |
Q: Just exactly how does this "Staybil" product work? I've been told to add it to my gas, then run the ...
A: Staybil works by adding chemicals to the gas to keep it from degrading over time. Fill your tank and ...
|
| cleaning a s&s carburetor | 11/6/2009 |
Q: I have a 76 FLH with a s&s carburetor, the carb leaks about a quarter quart of gas every night, with ...
A: First, you need to get a rebuild kit for the carb. Also, if your carb is leaking like that, your ...
|
| Repair front fork tubes | 11/5/2009 |
Q: I'm from Spain and I am not very good in english, but I try to ask you a question... Days ago I had ...
A: You will need to replace the seals as well. Have the bike sitting on a stand so there is no pressure ...
|
| 2006 fxdi bearing | 11/4/2009 |
Q: What can be done to prevent every 15000 mile bearing failer in my fxdi, Harley says it needs to be ...
A: Not really sure why they told you that. That bearing is not different than any other big bike. They ...
|
| Front fork repair | 11/3/2009 |
Q: I have a 1999 ultra classic, the left front fork has begin to leak fluid. Do I have to remove the ...
A: Your fork seal is probably leaking. You dont have to take the upper forks off to remove the lower ...
|
| bike shuts down | 11/3/2009 |
Q: I have a 2000 road king the bike shuts down when it gets warm/hot usually about 20 min riding from a ...
A: Your voltage is probably dropping and shutting the bike off. What you need to do is test the stator. ...
|
| 1967 Harley Sprint value | 11/3/2009 |
Q: I have had a 1967 Harley Sprint,sitting in my garage for a good 12 years. Before my garage, I was ...
A: Since its been sitting that long and the motor needs to be gone through, its not going to be worth ...
|
| primary leak | 11/3/2009 |
Q: I own a 2003 HD Superglide Sport. My primary drain plug is stripped out and leaking primary fluid. ...
A: You will hae to remove the primary cover and drill the hole out and install a insert so you can ...
|
| Eccessive Oil out of Breather | 11/2/2009 |
Q: I have an 88 Softtail with an S&S 96cu inch motor. I changed the cam shafts over the winter. The ...
A: there are two possible reasons. The cam you installed is a high lift cam and it is causing blowback ...
|
| Transmission | 11/2/2009 |
Q: I recently participated in a parade with my 1990 HD FXR. About half way into the parade the bike ...
A: First, you need to determine if its the clutch or trans. Jack the bike up and remove the spark plugs ...
|
| Valve job | 11/2/2009 |
Q: I thank you for taking the time to read this. My husband has an 81 Harley Sportster. It has sat for ...
A: First, you have to check the clearence of valves to valve guides. the guides usually wear and have ...
|
| engine stall | 11/1/2009 |
Q: why does a motorcycle engine stall when it's park under the heat of the sun for a couple of hours? ...
A: You never told me the year and model so i can only be general. You tank has to be vented or the fuel ...
|
| 1977 harley sporster | 11/1/2009 |
Q: How do I put a wide glide front end on my 77 sporster. I think I need a coupler? The other is on the ...
A: I dont know of any swing arm that you can put on your bike to install a wider tire. You may have to ...
|
| 1955 H-D Hummer and 1956 H-D K-KH | 10/29/2009 |
Q: Hey Mike this is Brad Streight of Odenton,Md.and I'm about to embark on restoring 2 H-D Motorcycles ...
A: For the hummer they made a 125 and a 165 CC model. Both were single cylinder and 2 stroke. On the K ...
|
| Heat Management | 10/28/2009 |
Q: Mike, I recently purchased a 10 screaming eagle ultra classic. The heat coming off the right side ...
A: If your bike is that hot, I would start by making the dealership repair it, not adding anything. its ...
|
| Hand Brake not illuminating brake Lights | 10/28/2009 |
Q: I have a 2003 Softail standard. When using only the foot brake, the rear illuminates. However, ...
A: Check your control housings where the brake lever is. You will se that its in two sections. They ...
|
| 96 ultra classic no start HOT | 10/27/2009 |
Q: A friend has a 96 ultra classic. for the last 2 years has been experiencing a no start hot ...
A: I would start by checking the voltage at the battery at idle. The volt meter on the bike could be ...
|
| Steering Head Adjustment | 10/25/2009 |
Q: Question #1: 2003 Heritage Softail Classic 30,000 miles. Noticed a slight rattle or jarring in the ...
A: Yes as long as you dont tighten it to much. As to question 2. they need to be inspected since you ...
|
| rear brake pads | 10/25/2009 |
Q: i need to replace rear brake pads on my 2007 Electra glide standard. I've done know how to do it on ...
A: remove the caliber. Pry the pads open so you have room to install the caliber back in with the new ...
|
| Gharging System | 10/22/2009 |
Q: How do you trouble shot the regulator and alternator on a 1991 Fatboy it was smoking where the ...
A: Your bike has a stator, not a alternator. What you do is take a OHMs meter and test the OHMs on the ...
|
| clutch tensioner | 10/22/2009 |
Q: Ok my question is simple to you but certainly not to I have a custom harley built on a 86 sporty the ...
A: To adjust the clutch, first loosen the cable at the cable adjuster so there is some play in it at ...
|
| 2000 sportster s | 10/21/2009 |
Q: i drop my bike and when i got it up i noticed all the wire at the right throttle controls were ...
A: You need to get a test light and start checking the wires for shorts and to make sure its wired back ...
|
| 1998 Harley Roadking -Oil Pan removal | 10/19/2009 |
Q: I have a 1998 Roadking with a Evo motor injected,and while doing a service on it the oil pan Drain ...
A: You can remove the oil pan without removing the trans. Its a tight fit but it will come out. I ...
|
| harley Spark Plug Thread Repair | 10/17/2009 |
Q: what is the best way to fix a Harley shovel head Spark Plug hole the rear cylinder has a heli-coil ...
A: I use stainless steel thread repair inserts. You hae to drill out the hole and install the insert. ...
|
| no spark | 10/17/2009 |
Q: i have a 02 harley duece soft tail carborated. drove it friday night and it was fine, pulled it out ...
A: If you have voltage at the coil and you installed a new modual the other thing it can be is the cam ...
|
| return cable 81 fx | 10/16/2009 |
Q: return cable broken. how do i repair it? thank you
A: Loosen the adjusters on both cables so there is slack in the cables. Remove the air cleaner and ...
|
| SU | 10/16/2009 |
Q: First the basic about bike its a custom job shovel mostly fxwg mid 80's stock motor std case kick ...
A: you never said if you have solid lifters or not. If you do have solid lifters check them. If they ...
|
| SU "Eliminator II" carburetor | 10/15/2009 |
Q: First the basic about bike its a custom job shovel mostly fxwg mid 80's stock motor std case kick ...
A: Your problem sounds like its not turning over fast enough to catch. Check your battery cables at ...
|
| shovelhead valve/piston collision | 10/14/2009 |
Q: Purchased a "best of everything" Shovel motor on Ebay. 93" S&S forged pistons,dual plugged ported ...
A: Without knowing what was done to the motor there are several posibilties. First, the pushrods might ...
|
| 1973 ironhead sportster | 10/14/2009 |
Q: So i pulled my timing cover and forgot to pull the points bolt out and pulled my cam out with the ...
A: Yes, the cam marks have to line up perfectly or your bike wont run correctly. So, make sure you ...
|
| 76 shovelhead wide glide | 10/14/2009 |
Q: I need to know how to wire up an indicator light on my dash to the oil sensor- I"ve downloaded a ...
A: The 12 volt power goes to the oil pressure senser, then a wire goes to the light from the senser. ...
|
| 2003 harley night train fuel problem | 10/13/2009 |
Q: 2003 standard stock 100 year anniversary night train with no part adds or changes was running fine. ...
A: First thing you need to do is determine if your fuel pump is working and pumping up. You would have ...
|
| oil pressure | 10/13/2009 |
Q: i have an 06 street glide with a 95 inch kit. in heavy stop and go traffic the engine will cut out. ...
A: Since your idle is jumping all around I would suggest getting a dianostic run on the bike. You may ...
|
| 84 Harley FXR Primary Adjustment & Frt Brake Master Kit P/N? | 10/13/2009 |
Q: Until I can get my hands on a manual, I need to know the procedure for adjusting the primary chain ...
A: Your rear one should be 42374-82A. To adjust the chain, remove the inspection cover from the center ...
|
| rear brake sticking | 10/13/2009 |
Q: I own a '92 softail FXSTC; the rear master cylinder is located on top of the fwd. control and stays ...
A: there is a spring inside the master cylinder that is used to return the master cylinder. Also, your ...
|
| Alternator Ring Lip broken | 10/12/2009 |
Q: I have a 1992 Dyna Glide with an oil leak. I found the lip on the case where the Alternator O-ring ...
A: I know that V-Twin Manufacturing used to make a kit for that repair, but they dont have them anymore ...
|
| 75 sporty tranny | 10/10/2009 |
Q: I just bought a 1975 harley sportster, when I start it up, pull the clutch and put it in first ...
A: Yoru clutch is sticking is the problem. Has nothing to do with the trans. First, loosen the cable so ...
|
| Race Tuner | 10/9/2009 |
Q: What is a race tuner and what does it do for the bike?
A: A race tuner is a program that is installed in your bike and what it does is change the settings on ...
|
| 84 FXRT Bad Clutch Drag Problem | 10/8/2009 |
Q: my 84 FXRT clutch really "drags". It is most noticeable when the engine and clutch is cold. Now that ...
A: It sounds like your clutch plates are sticking together. What you need to do is pull the plates and ...
|
| 1971 sporty clutch | 10/8/2009 |
Q: I bought a 1971 sportster and it jumps forward and stalls when i put it in gear. I have turned the ...
A: What is happening is the clutch is not releasing all the way. Loosen the cable at the adjuster so ...
|
| Starter | 10/8/2009 |
Q: I have a 1981 Sportster that sometimes the starter won't spin when I depress the starter button. ...
A: Looking at the starter you will see two wires going to it. The large one is from the battery and the ...
|
| '95 xl, 1200 evo | 10/8/2009 |
Q: New to Harleys, bike is in good condition, but still trying to get a feel for how she runs. recently ...
A: If the compensator nut nut, chain was loose or a bearing was worn in the primary you would get a ...
|
| 98 fatboy lights off engine runs | 10/8/2009 |
Q: I was riding my 1998 fatboy tonight down the freeway and all of the lights went off. The engine ...
A: I would start by checking all the lighting connections to make sure they are tight. Then you will ...
|
| Gas spill | 10/8/2009 |
Q: first please allow me to say that I did see your non-Harley warning. My question is not specific to ...
A: Your fuel leak could be from either the vent on the gas tank or the carb. If the bike was leaned to ...
|
| 1340 engine | 10/8/2009 |
Q: bike has sat for about 4months . I tryed to start bike acted like battery was low. when it started ...
A: Charge the battery up fully and start the bike. the oil coming out is just oil that has weeped past ...
|
| brake pads | 10/8/2009 |
Q: I never replaced brake pads before on my 2004 custom harley sportster. I need to change my fromt and ...
A: First, you need to take a screw drive and open the pads so the new ones will fit. Just pry against ...
|
| 99 Road King Starting Problem | 10/6/2009 |
Q: My 99 RK Classic will not start. It makes a feeble attempt but does not turn over. Thought it was ...
A: If you have 2.79 volts at the small wire on the starter then unplug it and see what the voltage is ...
|
| 08 Road Glide oil fouled plugs at 5K mi. | 10/6/2009 |
Q: My 08 Road Glide 5,000 miles I checked plugs and they are oil fouled.Slight oil weep from rear ...
A: It is not common for the valve seals to go bad. They should last a long time. You could have oil ...
|
| 2001 harley 883 | 10/5/2009 |
Q: This bike belongs to a friend who bought it new. The bike has 600 miles on it. My friend is a ...
A: I think what you are going to have to do is pull the motor and tear it down. You probably have a ...
|
| Harley Davidson Sportster Cutom 883, 2006 | 10/5/2009 |
Q: I own the above mentioned Bike, the problem is that everytime i start the bike , it runs for harldy ...
A: First, it takes a while for your bike to warm up. If the motor is cold it will sputter without the ...
|
| Cam timing | 10/5/2009 |
Q: I know you are a Harley mechanic but maybe you can help me. I am installing a new replacement cam in ...
A: Looking at the cam you will see two marks. One is for the cam timing and the other is to time the ...
|
| rear cylinder cuts out | 10/3/2009 |
Q: 2004 road king clasic, fuel injected, started riding and after about 8 miles riding the rear ...
A: Your EFI can short on one cylinder. Since your getting spark, I would start by checking to see if ...
|
| rear cylinder cuts out | 10/2/2009 |
Q: 2004 road king clasic, fuel injected, started riding and after about 8 miles riding the rear ...
A: Did you run a dianostic on the bike? If you didnt, you should. There are so many thing that can be ...
|
| revtech 100 | 10/1/2009 |
Q: bike ran great sunday custom chopper cranked but wouldn,t start monday. changed spark plugs ngk ...
A: Since yoru plugs are fouled that is what is causing yrou running problem. It sounds like your coil ...
|
| backfiring and spitting back | 9/30/2009 |
Q: I purchased a 2004 carbureted electra glide standard in 2008 with 3900 miles on it from an ...
A: Since your plugs are fouled, there are two reasons that can happen. First is your carb is jetted to ...
|
| Clutch problem on 1973 XLH | 9/29/2009 |
Q: I have a 1973 XLH Sporster. The problem started on a ride when I went to down shift and I lost ...
A: Thy this. Loosen the clutch cable so there is alot of slack in it. then loosen the clutch adjuster ...
|
| tank swap on 87 electra glide | 9/28/2009 |
Q: I have a 87 Electra Glide classic with the ugly square fuel door on the tank. I want to swap to late ...
A: The tank you are refering to would have to be modified to fit your bike. Check some of the ...
|
| high idle | 9/27/2009 |
Q: Mike I have had my 2008 XL1200L for a couple of weeks now and I don't like how high it idles. How do ...
A: Without knowing the idle speed I dont think you should lower it. The bike is designed to idle at a ...
|
| 2007 roadking police bike | 9/27/2009 |
Q: i am going to change lower legs and have never done this before and i have no books i do a lot of ...
A: I am going to suggest that you purchace a service manual if you are planning on working on your own ...
|
| FLHT-PI speedometer | 9/26/2009 |
Q: The speedometer on my 1999 FLHTPI quit working today as I was going down the road. The tach is ...
A: Not really. I would disconnect the cable from the speedo and jack the bike up. Spin the front wheel ...
|
| 1980 FXWG Ignition | 9/22/2009 |
Q: First,Thanks Mike on the oil pump info. it was air bound. As my hose go in from the top, I took the ...
A: If you go to the dyna web site you can get the instructional sheets for your ignition for the ...
|
| forks 73 Sprint | 9/22/2009 |
Q: Mike, sorry for the remedial questions, I am learning as I go. but, as I strapped down and brought ...
A: If you have released the pinch points on the triple trees, the part that the forks are in, and they ...
|
| installing ape hangers on a 2009 nightster | 9/22/2009 |
Q: I am trying to install 12 inch ape hangers on a 2009 nightster, what size cables do i need to get ...
A: Anytime you are installing taller handlebars wnat you need to do first is instll the bars. then at ...
|
| Stereo fuse/ brake light problem | 9/22/2009 |
Q: I have an 96 ultra classic Electra glide,just bought it, battery died, I replaced it, noticed that ...
A: Check the bulb and check the socket with a test light. If you dont have power to the brake light, ...
|
| Tappet block leak | 9/21/2009 |
Q: I have a 1991 FXRS and noticed a leak which should only be coming from the tappet block (rear ...
A: The only other thing it can be, if that is where the leak is, is a problem with the case where the ...
|
| ENGINE AND BATTERY LIGHT COMES ON WHILE RIDING | 9/20/2009 |
Q: I just finished the 10,000 mile service. The battery charge was 12.7 volts but the voltage while ...
A: Either the stator or voltage regulator is bad. You can ride with the battery charged, but when you ...
|
| 2005 HD Deluxe | 9/19/2009 |
Q: I need to bleed my brakes on my '05 Deluxe and I have it lowered "slammed" as far down as I could go ...
A: On your first bike. Pull the brake handle and crack the bleeder on the caliber. you will see brake ...
|
| harley charging system | 9/19/2009 |
Q: after reading and trying your(mike wells) answer to a previous question regarding checking the ...
A: Go from one prong on the stator to ground. then do the other. You should get zero OHMs. then go ...
|
| Drive Chain Adjustment | 9/19/2009 |
Q: How Do I adjust the Drive chain to Take out the slack on an 82 shovel Fxr?
A: loosen the axle nut. infront of the axle nut you will see the adjuster nut. Turn the nut on both ...
|
| Oil + Push rods | 9/19/2009 |
Q: I have an EVO 1340 from 85, I had a problem with a bearing which disintegrated and damage my E-27 ...
A: If you oil light is staying on, then you dont have enough oil pressure. You need to get a pressure ...
|
| fuel in oil | 9/19/2009 |
Q: Just bought an 02 Fatboy 88 ci, carburated, with 11,000 miles on it. Not sure how long it sat. ...
A: At one time the petcock was probably left open for a long period and gas leaked into the carb. If ...
|
| 86 FXST Solenoid/Starter ??? | 9/18/2009 |
Q: Won't start Just get a click from the solenoid when I press start an I lose power until something ...
A: If you have 12 volts going from the starter relay to the solenoid and you have 12 volts at the post ...
|
| Harley Starter problem | 9/17/2009 |
Q: I have a custom built high compression '97 80" Evolution motor. I am trying to determine if my ...
A: There are a coule different routes you can go. I would suppect that you running 10:1 or 12:1 ...
|
| S&S problems | 9/16/2009 |
Q: i have an 84 softail that has the S&S on it . it has never run right since it was installed. i just ...
A: It can. What the VOES does is change the timing when under throttle. It connects to the intake ...
|
| Removing Rocker cover bolts on a 2009 FLHX | 9/16/2009 |
Q: I want to take off my rocker box covers to have them powder coated, I have a 2009 FLHX (Touring ...
A: you dont need a special tool. Its just a tight fit. I use a shortened allen head. Any time you ...
|
| 2001 HD fuel injection | 9/16/2009 |
Q: I have a 2001 Electra Glide Ultra Classic with 7000 original miles. Lately when starting the ...
A: On the throttle no going into high idle, your temp senser is probably going bad and not kicking hte ...
|
| 2002 XL1200C Backfire through Carb | 9/15/2009 |
Q: Good Afternoon Mike, I have acquired a 2002 XL1200C that has developed a backfire through the carb. ...
A: I would doa OHMs test on the coil and plug wires. That can cause your problem. Also, check for a ...
|
| 1972 flh | 9/15/2009 |
Q: please tell me the procedure for filling the front forks with oil. The manual tells me to make a ...
A: Jack the bike up so there is no pressure on the forks. Remove one top cap on the fork. Do it ...
|
| back fire | 9/15/2009 |
Q: Mike ,i own a 2006 fhltc .I've installed a set of rinehards mufflers on it.Since then i have a ...
A: Youn dont need to go to a bigger air filter, but I would recommend it. It will let your bike breath ...
|
| oil pouring out of the breather vent line | 9/14/2009 |
Q: early 1985 flht,bike has been sitting since 2004.put new battery in, it started right up,but oil was ...
A: No, nothing is stuck. The oil tank sits higher than the motor. There is a check valve in the oil ...
|
| Rejetting super g carb | 9/14/2009 |
Q: I am repacing the stock 2in1 pipes on my 06 ironhorse lsc with vance n hince bid radius 2in 2 pipes ...
A: If you go to the S&S web site and go to the tech pages you will find how to jet your carb. The ...
|
| leaking fluid on clutch cable | 9/14/2009 |
Q: cable has had fluid leaking where it swings down to frame. I pulled the plug on the reservoir, and ...
A: Since the cable goes into the trans, I am going to assumn you are refering to the level of the trans ...
|
| ironhead 1000cc and shorty super e carb. | 9/13/2009 |
Q: i have a early 84 ironhead 1000 and put a shorty super e S&S carb. on it . it had a inter. of 29 in ...
A: A good coil is either a Crane or Accel. Make sure you get one for your bike depending on if you have ...
|
| oil leak | 9/13/2009 |
Q: i have oil coming out of the exhaust pipe on a 1450cc engine with only 2500 miles on it what would ...
A: there can be two reasons for oil coming out the exhaust. Oil is leaking past the valve guides or oil ...
|
| 2001 Road King FHLRI | 9/13/2009 |
Q: Rear tire is not center with rear fender seems like rear swing arm is bent. Recently had an accident ...
A: You can buy a new swing arm and install it, but I would check to make sure the fender struts are not ...
|
| LED taillights | 9/13/2009 |
Q: I have an 06 Street glide. I have removed the stock brake light asmembly and rear turn signals. I ...
A: I am confused. Why are you wiring the turn signals to the brake light? If you wire them to the brake ...
|
| rear brake master cylinder 1995 Fatboy | 9/13/2009 |
Q: My rear brakes went out. I tried fluid and bleeding, all I get is sputters and nothing coming out ...
A: Your parts inside the master cylinder are being held in by dirt probably. You can use air pressuse ...
|
| electrical problem | 9/12/2009 |
Q: I have a 2000 model Deuce. I decided to change my seat from a rider and passenger to a solo seat. ...
A: the stator runs in the primary oil to keep it cool. If you are getting oil at the plug then the ...
|
| Blow back | 9/12/2009 |
Q: Wells, I have a serious blow back problem that caauses me to lose 1 qrt of oil in less than 100 ...
A: You can probably do the work yourself without problem. If you need a oversize breather you would ...
|
| electrical problem | 9/12/2009 |
Q: I have a 2000 model Deuce. I decided to change my seat from a rider and passenger to a solo seat. ...
A: You are showing to low of voltage for your bike. You should be showing around 13.5 volts. When you ...
|
| Blow back | 9/11/2009 |
Q: Wells, I have a serious blow back problem that caauses me to lose 1 qrt of oil in less than 100 ...
A: Your crankcase breather is probably worn and oil is getting past it. What you need to do it remove ...
|
| 74 harley sportster electric start right side shift wont start | 9/11/2009 |
Q: OK here is the story/question sorry if its a lil long now all i gotta do is figure out how to get ...
A: When it does it check to see if you have power going to the starter solenoid from the starter relay. ...
|
| 1999 Heritage Clutch Plate/Disks replacement | 9/10/2009 |
Q: Need to replace clutch plates/disks on 1999 Heritage. I currently own an 84 Shovel and have done all ...
A: No problem. Drain the primary fluid. Remove the primary cover. In the center of the clutch you will ...
|
| 1970 XLH Carb issue | 9/10/2009 |
Q: I have another question for you. I just rode my bike today for the first time in 5 years{70 XLH). ...
A: Start the bike and let it warm up. Set the idle at around 900 RPM. The screw at the rear is for a ...
|
| Fuelpump | 9/10/2009 |
Q: I have a 2000 FLHTCI and my fuelpump doesnt always turn on. If i turn the turn the ignition switch ...
A: Sounds like you have a short in the switch. Check both sides of the switch to see if you have power ...
|
| no spark | 9/9/2009 |
Q: I have no spark on my 94 flt could the Voes switch or the wires going to it shut down the ignition. ...
A: Since you have replaced the above parts and its still doing it then you either have a bad breaker or ...
|
| remove forks | 9/9/2009 |
Q: I just bought a 2006 street bob and the upper forks are bent. Can you tell step by step ...
A: Jack the bike up and remove the fender, brake caliber and wheel. On the fork you will see a screw on ...
|
| lower rpm on hwy. | 9/8/2009 |
Q: I heard you can change rear sprocket and it will lower you rpm on hwy? I have a shovelhead 4 speed , ...
A: If you want to lower your RPMs on the hyw you would have to either go smaller on the rear sprocket ...
|
| New Handlebars | 9/8/2009 |
Q: I would like to know the best place on 09 Night Train where hand control wires can be disconnected ...
A: The wires are plugged in under the tank. You have to drain the tank, disconnect the fuel lines and ...
|
| no oil pressure 07roadking | 9/8/2009 |
Q: i have 7300 miles on my rk was riding down highway 65mph eng. sounded a little loud look down oil ...
A: You would have to remov ethe oil pump and do an inspection on it. In order to do this you have to ...
|
| clutch | 9/7/2009 |
Q: 1980 harley shovehead 4speed new clutches basket spring. always had problems with clutch wanting to ...
A: No, you dont soak the disks. They are dry clutches. You do your mesurement from the back of the ...
|
| Binding Clutch on 1960 XLCH Sportster | 9/7/2009 |
Q: I am the third owner (since 1971)of this stock beauty but the clutch has been a problem. I think ...
A: Sticking clutch plates were always a problem. One of the things that causes the problem is sitting ...
|
| Starter or soleinod | 9/7/2009 |
Q: I have a 2000H.D. heritage Softail.All has been good till now.Sounds like starter spins but doesnt ...
A: What you need to do is drain the primary fluid and then remove the rear cover. looking above the ...
|
| Rich Fuel Adjustment | 9/7/2009 |
Q: My '98 FLSTC has been running rich since the 95K service. It will start without the enrichener at ...
A: On your bike you have a air/fuel mixture screw which is plugged. If you are running rich all the ...
|
| 1992 FLHT | 9/6/2009 |
Q: I HAD RODE ALL DAY, I STOP TURN OFF THE BIKE ABOUT 20 MIN, GOT BACK ON, TURN BIKE ON MUSIC CAME ON, ...
A: You dont have fuses, you have breakers. Check the main breaker going to the ignition switch and see ...
|
| 79 lowrider charging system | 9/5/2009 |
Q: when riding my bike it stalled and would not start.only has kick start and head light was dull ...
A: First, charge the battery and start the bike. At the battery, you should be showing about 13.5 volts ...
|
| OIL CHANGE | 9/5/2009 |
Q: WERE ARE DRAIN PLUGS ON 2000FLHRI, AND WHAT IS CAPACITY
A: The oil drain plug is located under the bike on the oil pan to the left and foward. The trans is ...
|
| VOES | 9/5/2009 |
Q: My 1993 FXDL drops it's idle speed ~300 RPM, on restart, after it's gotten hot idling then turned ...
A: What the VOES does is advance the timing after the bike is running. You can chaeck it by starting ...
|
| harley | 9/5/2009 |
Q: Harley-Davidson 2006 flhtc electra glide classic with a starting problem, was running then just quit ...
A: What you need to do, before changing the fuel pump, is do a test pressure to see if its pumping up ...
|
| Gearbox seal on WLA 42 | 9/5/2009 |
Q: The main shaft gearbox seal on the clutch side leaks oil like a sive, filling up the clutch with oil ...
A: You can replace the seal without tearing the trans apart. Its on the outside of the trans. You have ...
|
| Harley 883 Sportster Battery recharge | 9/3/2009 |
Q: My wife bought a Harley 2009 883 Harley. She has not driven it in a while, she went to turn it on it ...
A: Remove the strap that holds the top cover and then remove the top cover. If you have a front cover, ...
|
| starting problems | 9/3/2009 |
Q: I just bought an 87 Harley Sportster 883 although the gentleman had it bored to a 1200. When I try ...
A: First, make sure you have a good battery. If you have a weak battery it wont turn over. Next, with a ...
|
| 1988 FXRS STARTER PROBLEM | 9/2/2009 |
Q: I Have a 1988 Harley FXRS. It has 10 to 1 compression with no releases on it. It also has a baker ...
A: Since you are running a high compression piston, the stock starter isnt handling it. Its taking so ...
|
| harley Vibrations | 9/1/2009 |
Q: Have 05 electra glide standard 43,000 miles. have small cams and race tuner installed. I have a ...
A: Your telling me somthing different than before. Since you say that the vibration quits then its a ...
|
| 07 ultra random misfire | 8/31/2009 |
Q: i have an 07 ultra that around 2000 rpm has a misfire i have replace plugs, wires,installed a new ...
A: Right now it could be about anything, but I would say its a intermitment short. Your best bet is to ...
|
| LIGHT PROBLEMS | 8/31/2009 |
Q: I HAVE A 99 FXSTC AND MY LOW BEAM AND MY REAR RUNNIN LIGHT DOES NOT WORK. I HAVE HIGH BEAM AND AND I ...
A: First, remove the bulbs and with a test light check to see if you have power at the posts for the ...
|
| Oil Temp | 8/30/2009 |
Q: I have a 1998 road king FLHRCI, I bought this bike about three years ago and had always noticed that ...
A: Your oil is staying to cool from the oil cooler. You need to have a thermostate bypass onthe cooler. ...
|
| harley sportster 1974 | 8/30/2009 |
Q: how do the oil lines run on a 74 xl 1000 sportster and what could cause intermitent pumping of my ...
A: Since this started when you had the gaskets replaced, it sounds like the oil pump is not working ...
|
| starter | 8/30/2009 |
Q: 1982 FLH rear belt drive, changed rear belt drive to chain drive,installed new ...
A: Kickback on the starter might not mean high compression, it might mean the timing is advanced to ...
|
| Motorcycle repair training?? | 8/30/2009 |
Q: I have two bikes that I would like to learn to PM and take care of myself. Do you know of or ...
A: I dont know of any classes around you. Your best bet is to get a service manual for your bikes. They ...
|
| 2003 dyna fxd clutch adjustment | 8/30/2009 |
Q: Adjusted for slack(a lot) at handle. loosened lock nut and turned in threaded srew several times. ...
A: It could have broken off inside. Try this first. Loosen the cable and then adjust the clutch. Slowly ...
|
| Timing a 1974 FLH that will not start | 8/29/2009 |
Q: How can I time my 1974 FLH when it will not start? It sat for 19 years but was turned over often. ...
A: Since you put the timing back where it was, your timeing is probably not off. It sounds more like ...
|
| brakes | 8/29/2009 |
Q: what is the best way to bleed the rear brakes on a 2006 Sportster took off caliper wiped it down ...
A: Go to the bleeder and pump the brakes a few times. With the lever pushed down, crack the bleeder and ...
|
| oil blowing out of breather tube | 8/29/2009 |
Q: Mike, I have a 1974 1000cc Sporty.When I start my bike in the morning a lot of oil shoots out of the ...
A: What is happening is oil is weeping past the check ball in the oil pump and getting into the bottom ...
|
| harley problem | 8/29/2009 |
Q: 97 heritage springer soft tail haveing trouble with passing lamp they stay on and every couple of ...
A: If the lamps go off, but not the headlight, then you have a short in the wiring going to the lamps. ...
|
| adjustment of rear belt | 8/29/2009 |
Q: I own a 2003 fxd. I just installed a new rear tire. What is the best way to tighten the belt ...
A: Put the gage on the belt and push up to the mark on the gage and measure how far the belt flexes. ...
|
| wet sumping | 8/27/2009 |
Q: I have a 83 flht (just bought) put new cams in,new pistons,new oil pump, have oil blowing out the ...
A: Your having a little oil sump in the bottom end of the motor. The pol pump cant pump it back fast ...
|
| Clutch Cable 2000 Ultraclassic. | 8/27/2009 |
Q: My cable broke at the clutch handle. How do you change the cable out?
A: First you have to remov ethe rear exhaust pipe and then drain the trans oil. Yu next have to remove ...
|
| Rough running HD | 8/27/2009 |
Q: I have a 2003 Harley Davidson Road King Classic. When the gas tank is full the bike runs well. ...
A: No problem. It sounds like your fuel pump is either plugged, the filter is plugged or the fuel line ...
|
| breakers 95 heritage | 8/26/2009 |
Q: I went to start my bike and it started to turn over and then I heard a click from under the seat ...
A: there are two reasons that a breaker will click. Either you have a bad breaker or you have a short ...
|
| Front Brake Light | 8/25/2009 |
Q: I have a 1996 Harley Road King. My brake light will not work when the front brake is applied but ...
A: There is a switch behind the brake lever. Check to see if you have power at the switch. When the ...
|
| 83 harley clutch ramp assembly for xlx1000 | 8/25/2009 |
Q: I need to know how the clutch cable attaches to the clutch ramp assembly on a 1983 harley 1000 ...
A: I dont have any diagrams to send you. the cable attaches by the end coupling that is in the ...
|
| head /valves repair | 8/20/2009 |
Q: 63 flh. recently got the bike running. bin sitting for some time. mechanically only had oil pump ...
A: Since you are probably working with a panhead motor the valves you need are part number (intake) ...
|
| Loosing Gear | 8/18/2009 |
Q: I just had a 10K service done on my 2006 Deuce. After I got it back when I upshift from second to ...
A: First, you need to check the shifter adjustment on the trans to make sure the shifter fork is in the ...
|
| starter | 8/16/2009 |
Q: I just got a 79 lowrider shovel, it has a 5 speed and computer on it, it was running no problem the ...
A: Check the wire going from the starter relay to the starter solenoid. If you have power at that wire ...
|
| 1978 Shovelhead | 8/15/2009 |
Q: I have a 1978 Shovelhead FL I have been experiencing a bad front end wobble between 40 to 50 MPH. ...
A: When you replaced the bearing did the you replace the race as well? If not then you will get a ...
|
| clutch adj. | 8/14/2009 |
Q: I have loosen my cable and locknut on adjuster but i cant feel when to stop turning screw it just ...
A: First, loosen the cable so there is slack in it. Now slowly turn the asjuster screw inward until you ...
|
| replace clutch cable on 1980 FLH | 8/14/2009 |
Q: Is there an easier way to change the clutch cable than taking half the bike apart? I can't figure ...
A: Loosen the cable so there is alot of slack in it. remove the cable from the clutch lever then the ...
|
| harley ignition coil problems--95 sportster | 8/14/2009 |
Q: Motorcycle has been running good. Last time i tried to crank, it was hard to crank. Finally crank, ...
A: Remove the coil. Test at the small wires with a OHm meter and you should get around 3.5 OHMs. Test ...
|
| oil leak/pouring | 8/13/2009 |
Q: I have a 1975 sportster 1000 and oil seems to come up through the vent tube and also the filter ...
A: There is a check ball valve in the oil pump that is suppose to close when the bike is not running. ...
|
| dead battery | 8/13/2009 |
Q: I have a 1998 Fat Boy and I have put 2 batteries on it this summer and I only get to ride it about ...
A: First, charge the battery and start the bike. With a volt meter check at the battery. You should be ...
|
| idel too low/ backfire | 8/12/2009 |
Q: My question to you is which screw on the carb sets the idol and which way do I turn it to increase ...
A: If you have a bad battery, it will cause the backfiring problem. Not enough juice to make a hot ...
|
| 1998 Harley Davidson Road King Classic | 8/12/2009 |
Q: I own a 1998 Harley Davidson Road King Classic. The bike has 55k miles. I am not the original owner ...
A: One thing you have to consider is if you sell it like it is you not going to get much for it, ...
|
| 1998 Road King Classic - Not starting. | 8/11/2009 |
Q: I live in South Africa and bought my Road King new in '98. Have loved it and had no problems until ...
A: Ok. Since you know you have good ground test the battery to make sure its good. If the battery ...
|
| transmission fluid leak/ 2002 nighttrain | 8/11/2009 |
Q: I purchased a 2002 nighttrain a couple months ago and noticed it started leaking transmission fluid ...
A: Either one can leak over time. What you need to do is really claen the area as wella s you can, then ...
|
| clutch hub | 8/11/2009 |
Q: how do i pull the clutch hub on a 1985 evo wide glide after i have removed the diaphram
A: You have to remove the nut holding he hub on as well as the motor sprocket nut, and the chain ...
|
| 1998 Sportster 1200 Custom | 8/11/2009 |
Q: I purchased my bike used from the dealer 1.5 years ago. It only has 12,400 miles on it. I have put ...
A: You should have 12 volts at the hot side of the coil, with the key on. Yes, the coil is located ...
|
| REPAIRING FORKS ON SPORTY | 8/10/2009 |
Q: I HAVE A 1996 883 HUGGER SPORTSTER. THE FORKS HAVE NO STIFFNESS(SLIDE UP/DOWN EASILY). I WANT TO ...
A: It sounds like you need the oil replaced in the forks. Start by draining the oil. At the lower fork, ...
|
| intake leak on 2002 Road Glide | 8/10/2009 |
Q: Hoe do you repair a intake leak. ANSWER: Carberated or fuel injected? Mike ---------- FOLLOW-UP ...
A: First, drain the tank and remove. Remove the air cleaner and carb. The choke will have to be removed ...
|
| Transmission Leak | 8/9/2009 |
Q: I have a custom chopper with a 80ci evo motor and a Spyke 6-speed transmission. It has a 3" open ...
A: There are two seals on the that side of the trans. The main seal and the seal inside 6th gear on the ...
|
| 85 ironhead clutch | 8/8/2009 |
Q: I have an '85 Ironhead, I can't seem to get the clutch adjusted, when I adjust it (by the book) the ...
A: Adjust the cable so it has alot of slack in it. loosen the adjuster on the clutch. Now take the ...
|
| Clutch keeps coming out of adjustment | 8/8/2009 |
Q: I have a 2008 Softail Custom, I bought it from Harley and it was a rental. Every time I take it to ...
A: Its probably your throwout bearing. What you need to do is replace it as well as the clutch rod. the ...
|
| 82 shovel clutch problems | 8/8/2009 |
Q: we replaced all clutch components even push rod and bearing when i pull clutch in and put it in gear ...
A: Check your adjustment on the clutch. loosen the cable so you have slack on it. Then go to the ...
|
| s&s motor vibration,compensator nut loosened up | 8/7/2009 |
Q: we have an 07 ironhorse with an s&s 111 in it,200 miles on it,compensator nut,come loose and took ...
A: When your nut came loose you might have damaged the compensator and its out of round. the only other ...
|
| shovelhead brake problem | 8/7/2009 |
Q: I have a 1970 Harley Electra GLide with rear brake problems. Sometimes it works, sometimes not. ...
A: You must be refering to the brake caliber on the left side of the wheel. If you dont have any leaks ...
|
| 2003 Lowrider | 8/7/2009 |
Q: I have a 2003 low rider. It was not started for 2 years. I have replaced the battery and fuel ...
A: If the motor is turning over and not firing, then first, pull the plugs and see if you are getting a ...
|
| 66 Shovelhead | 8/7/2009 |
Q: I have a 66 Shovelhead that I am getting back to good working order. I have installed new points, ...
A: You might have the incorrect shaft. The shafts for your bike runs 65-69 and then there was a change. ...
|
| 2003 Lowrider | 8/7/2009 |
Q: I have a 2003 low rider. It was not started for 2 years. I have replaced the battery and fuel ...
A: What you need to do is see if you hve power going to the starter. First, chect to make sure you hve ...
|
| 111 s&s noises | 8/6/2009 |
Q: ANSWER: Did you just put the motor in 300 miles ago, or did you put the motor in in 06? Mike ...
A: Your ticking is from the hydrolic lifters. There are a couple of things to try to stop it. Once is ...
|
| front fork seal | 8/5/2009 |
Q: i have a 2006 dyna low rider with 49mm tubes on the front forks i would like step by step ...
A: First you need to jack up the bike and remove the fender, brake caliber, axle and wheel. Slide the ...
|
| 73 xlch won't take throtle | 8/4/2009 |
Q: hope you can help . First i have a 73 xlch that i rebuilt this year. the flywheels were ...
A: Your plugs are fine with the 28 jet. Couple of things to check. Check the points to make sure they ...
|
| gas fouled plug | 8/4/2009 |
Q: i asked you a question about rear cylinder only gas fouled plug only last week.i should have ...
A: Since you only hae one cylinder that is fouling, the cam cam be off, if they were removed so I would ...
|
| Breaking cables!! | 8/4/2009 |
Q: Hey Mike, I have a 1200c with 12" mini apes, I originally put Magnum II cables all the way around ...
A: I dont think you are doing anything wrong. Make sure you dont have any really tight bends in the ...
|
| 73 xlch won't take throtle | 8/3/2009 |
Q: hope you can help . First i have a 73 xlch that i rebuilt this year. the flywheels were ...
A: On the RPMs, just estimate. If your going about 30 MPH you will be under the 2500 RPM. The 32 ...
|
| lifters | 8/3/2009 |
Q: Its Mario from OZ.I have a 92 dyna glide coustom evo 80 cube.Mike,can you test hydraulic lifters for ...
A: When you get the kit from S&S it will come with instructions for installation. There is no test I ...
|
| S&S 88 ci engine | 8/3/2009 |
Q: This is the engine on my Indian, 2001 Spirit. Although it is not a Harley, the Indian uses the same ...
A: The service manual is the repair manual, unless you have a owners manual instead of the service ...
|
| 1984 FXR | 8/3/2009 |
Q: Hey Mike, I've got a 1984 FXR-SP frame w/ a 91' motor in it. My front end is very mushy and I want ...
A: Measure the upper fork tubes and that will tell you what forks you have. If they are sportster tubes ...
|
| 73 xlch won't take throtle | 8/2/2009 |
Q: hope you can help . First i have a 73 xlch that i rebuilt this year. the flywheels were ...
A: It sounds like you have carb problem. Lets start at the begining. Start the bike and let it warm up. ...
|
| starter | 8/2/2009 |
Q: 1989 FLT starter button makes starter click but wont engage but can jump across and starts fine ...
A: I would clean the ground wire and make sure its tight. Since you have 12 volts to the relay and only ...
|
| Volt meter fluctuation | 8/2/2009 |
Q: I have a '96 Electra Glide Classic. When the bike is running, my volt meter on the dash shows a ...
A: First, hav the battery tested to make sure its good. In order to do that you need to do make sure ...
|
| Wheel Bearing Repacking | 8/2/2009 |
Q: I own a 1997 Harley Sportster 883. Can you tell me the procedure for packing the wheel bearings ...
A: Remove the wheel and the bearing seals. Remove the bearing, one at a time and clean all the grease ...
|
| Harley Ignition switch removal | 8/1/2009 |
Q: How do you replace an ignition switch on 1980 Harley Davidson flt with no key.The key was lost when ...
A: One thing you might try is going to a dealer and with the vin number they might still be able to ...
|
| trans sprocket | 8/1/2009 |
Q: hi mike just like to know if trans sprocket on 73 xlch has to be set atcertain tension or just ...
A: There is not torque for the trans sprocket. Just tighten it tight. On the pushrods, they should be ...
|
| oil change | 8/1/2009 |
Q: where do you drain the oil on a 2001 FLHTCI Electra glide. I cant seem to find the oil tank.
A: the oil tank is under the bike. Looking from the right side of the bike, under the trans you will ...
|
| 2000 Harley Davidson Wide Glide | 7/31/2009 |
Q: Engine light comes on, odometer flashes on and off 30 seconds after bike starts, put new battery in, ...
A: You are charging fine. Since your check engine light is coming on what you will need to do is hae a ...
|
| '84 softail starter | 7/31/2009 |
Q: My '84 softail starter grinds when I use it. There are obviously some broken teeth somewhere. I know ...
A: You have to pull the starter and behind the starter you will find a cover for the gear. It will have ...
|
| torque specs | 7/30/2009 |
Q: I have a 1994 Road King 1340 big twin I am going to put new gaskets from cylinders up what are the ...
A: To torque the heads you start with the front one on the left side if the bike and at the front ...
|
| Fuel controller needed? | 7/29/2009 |
Q: I have an 08 fatbob stock except for kromewerks slip-on mufflers (hp-3) just installed. Do I need a ...
A: About he only way for you to tell, unless you run the bike on a dyno, is to pull the spark plugs and ...
|
| overheated, cracked front disc | 7/29/2009 |
Q: Had my '89 Sporty in the shop for a new clutch and stator. While in the shop the mechanic noticed ...
A: There is no adjustment to the brake. You have a disk brake and the only thing that needs done is ...
|
| Idling | 7/28/2009 |
Q: I ride a misfit of parts, but I love her. I have had her for 5 years and have had her to at least 4 ...
A: Your bike Never had a VOES. Harley didnt start using them until 84. Once you start the bike, you ...
|
| STUCK EXHAUST VALVE | 7/28/2009 |
Q: Hey Mike,I have a 73 shovel and the bike runs like it is out of time but it happened once before and ...
A: If your valves stick, then they are to tight in the valve guides. There is a clearence that needs to ...
|
| starter trouble | 7/27/2009 |
Q: My starter has blown on my '04 XL1200r. Is this a job that I can do myself? Any advice on the kind ...
A: In order to remove the starter, you have to remove the primary cover to get to the starter bolts. ...
|
| 73 sportster xlch | 7/27/2009 |
Q: transmission drain plug was striped out then helicoiled.after years of taking plug in and out part ...
A: JB weld isnt going to work and a self tapping plug will probably strip out in time since the case is ...
|
| low idle on fuel injected bike | 7/24/2009 |
Q: 2001 road king, 49,000 miles, bike is fuel injected. Everything stock. once the bike warms up, 5 ...
A: there are several things that can cause your problem. Throttle position senser is going bad, temp ...
|
| 2005 twincam A from a dyna lowrider fits what other frames? | 7/24/2009 |
Q: have a dyna twincam88A carbuerated w/tranny what year frames will it fit? only Dyna family or will ...
A: Hate to say this, but I messed up! The engine and trans you have will fit any FX type frame. You can ...
|
| Primary chain | 7/23/2009 |
Q: I have a 2002 Electra glide classic. I am told I should adjust the primary chain when it starts to ...
A: You should check your primary chain about every 3000 miles. the chain is located inside the primary. ...
|
| sporster spedo fuse | 7/23/2009 |
Q: I have a 1999 1200c and i tried to relocate my speedo. it was working fine on the test drive. when i ...
A: The fuses are located under the right cover or under the seat. There is no special fuse for the ...
|
| oil blowing past air cleaner | 7/22/2009 |
Q: why would oil be blowing past my air cleaner filter its a 2004 dyna low rider with 6200 miles about ...
A: Your heads are vented by the two bolts going into the heads close to the carb. At times a small mist ...
|
| changing starter | 7/22/2009 |
Q: I have taken clutch cover ,foot peg and all bolts out of chain cover i cant get the gear shift to ...
A: the gear shift will slide off if you have the bolt out. Its just tight. You may have to pry it off. ...
|
| throttle/idle cable adjustment | 7/22/2009 |
Q: I have a 2004 sportster883.I REPLACED THE STOCK BARS WITH A SET OF BARS OFF A 2008 CROSSBONES.THE ...
A: Go to the adjusters on the cables. They are close to the throttle. Loosen the locknut and turn the ...
|
| baffle? | 7/21/2009 |
Q: I recently participated in a parade with my 1990 HD FXR. About half way into the parade the bike ...
A: I doubt if the baffle came loose. Slow riding, like you were doing is really hard on the air cooled ...
|
| 1999 Harley 1200 Sportster rocker box gasket | 7/21/2009 |
Q: What is the process in changing rear rocker box gasket on a 1999 Sportster 1200. Any info would ...
A: Remove the tank and remove the 4 allen head bolts holding the top cover on. Remove it and the center ...
|
| 06 harley ultra classic fork slider removal | 7/20/2009 |
Q: Mike Can you tell me an easy way to change out the lower fork sliders.Have a new set that are ...
A: Start by draining the fork oil. Remove the front wheel, fender and brake calibers. Inside the under ...
|
| Front end for a 2007 Sportster | 7/20/2009 |
Q: My wife has a 2007 1200XL Low Rider and we are wanting to make it look real "Beefy". She likes the ...
A: About the biggest tire you will fit is a 130/90-19 Companies do make 41 MM front ends for ...
|
| low beam blowing fuse | 7/20/2009 |
Q: We have a 1997 Road King. Just noticed the problem yesterday. When you switch from high to low beam ...
A: When you blow a fuse, like you have, you have a grounded wire somewhere. What you are going to have ...
|
| 79 sportster | 7/19/2009 |
Q: could you tell me how much clutch oil goes in a 79 sportster
A: Looking at the bottom of the primary, close to the center, you will see a small screw. Remove it and ...
|
| 2000 sportster clutch cable replacement | 7/18/2009 |
Q: just wondering how to get the cable out of gear box shift lever. thanks GARY ANSWER: You first ...
A: If you are removeing the cable then you have to remove the primary cover. To remove it you need to ...
|
| 2000 sportster clutch cable replacement | 7/18/2009 |
Q: just wondering how to get the cable out of gear box shift lever. thanks GARY
A: You first have to shorten the cable with the cable adjuster. It is located under a rubber boot in ...
|
| 2006 Harley Davidson touring bike. | 7/18/2009 |
Q: We bought a bike and the previous owners lied to us.The neck and frame were pushed slightly to the ...
A: In the old days, Harley used to put the measurements in their service manuals, but they dont do it ...
|
| replacing clutch hub | 7/18/2009 |
Q: how do i get the clutch assembly out of the old clutch hub on a 1998 fatboy?
A: Drain the primary fluid and remove the primary cover. Behind it you will see the clutch. Loosen the ...
|
| 2002 Harley Dyna Super Glide charging problem | 7/18/2009 |
Q: I have a 2002 Dyna Super Glide. The battery looses charge when the engine is running. The red ...
A: for the OHMs use the lowest setting. Yes, they have to show no OHMs. If they do then it means it ...
|
| excessive oil | 7/18/2009 |
Q: i recently bought an 87 electra glide classic.it has just under 17000 km,s(ya i'm canadian).during ...
A: If you have oil in the primary, other than primary oil, then its coming through the main seal behind ...
|
| 2002 Harley Dyna Super Glide charging problem | 7/17/2009 |
Q: I have a 2002 Dyna Super Glide. The battery looses charge when the engine is running. The red ...
A: You need to test your stator. First, do a OHMs test on the stator wires. From one wire to ground, ...
|
| top end job | 7/17/2009 |
Q: I own a 97 Road King with 103,000 miles. Exactly what goes into a top end job. I ask this question ...
A: When the heads are removed the base gasket has to be replaced or it will leak, but like I stated ...
|
| 1998 Roadking fuel Injected 50k phaseII racing cam Straight pipes with Power cones | 7/17/2009 |
Q: I have a problem of this bike being in two different shops and no one can fix( anwser is buy new ...
A: First, you need to fix the intake leak in order to get the bike running right. Since the plugs are ...
|
| Front end for a 2007 Sportster | 7/16/2009 |
Q: My wife has a 2007 1200XL Low Rider and we are wanting to make it look real "Beefy". She likes the ...
A: You can go a wide as the forks will allow. You have to keep in mind that the brake caliber has to ...
|
| 2003 Low Rider Oil Pan | 7/16/2009 |
Q: My oil pan has stripped drain plug threads and I have to replace it. The manual makes it sound easy, ...
A: You dont need to jack up the motor, unless you want to. If you look at the top of the engine you can ...
|
| Valve noise | 7/16/2009 |
Q: Mike, I have a 2006 FXSTI that has about 6700 miles on it. The motor is stock and has had no work ...
A: As long as you change your oil when you are suppose to the oil is not breaking down. With heat the ...
|
| oil | 7/16/2009 |
Q: i have a 1991 haritage has been sitting for few months when i tried to start it the engine started ...
A: What had happened is over time oil from the oil tank has weeped into the bottom end. When you start ...
|
| 69 FLH Clutch plate dimentions | 7/15/2009 |
Q: Mike, can you give me the factory specs on what the '69 FLH clutch plate tolerances are? Thanks.
A: There really is no tolerence. Harley never gave one in the service manal. It was left up to the ...
|
| Primary Gasket | 7/14/2009 |
Q: I have a 94/883 sportster hugger Harley Davidson. I have a small oil leak and believe once the ...
A: Time should take you about 45 minutes. First, drain the fluid. Loosen the adjuster on the cable so ...
|
| Clutch basket repari | 7/14/2009 |
Q: Hoe do remove and replace the Clutch Basket on a 1997 Heritage Soft Tail? I had a a little issue ...
A: You are going to need a clutch compression tool to remove the clutch basket. You would have to ...
|
| Super E Carb adjustments | 7/13/2009 |
Q: I have a 1983 FLH with a Super E carb. It was running fine until I brought to a wrench who "tried" ...
A: First thing you need to determine is if its the carb or somthing else. Since your plugs are fouled ...
|
| harley master cylider | 7/13/2009 |
Q: i have a 2006 softail standard,just brought new chrome handle bar controls,put them on and pulled ...
A: Pumping it before putting brake fluid in didnt hurt anything. The hole in the master cylinder, where ...
|
| Rear Tailights/Not Flashing | 7/13/2009 |
Q: Mike, as you suggested i rechecked the connection of the load equalizer. It still did not solve the ...
A: Since your filament bulbs work then your wiring is ok. The only things it can be is (1), load ...
|
| 1977 sportster starting problem | 7/13/2009 |
Q: I had a 77 ironhead rebuilt a few years back by a dealership, they did not start it when doen as i ...
A: you should set the air/fuel mixture screw at about 1 1/2 turns. I idle screw can be set until the ...
|
| oil out of carb | 7/12/2009 |
Q: yes hi i have 2003 sporsterxl and someone told me that oil getting spitted out of carb is caused by ...
A: On each side of the carb, in the head, there are two bolts. They are hollow and they vent the ...
|
| Sportster Running HOT | 7/12/2009 |
Q: I have a 92 Sportster with a 96-03 1200 motor(previous owner says it is a 2000). When I got it the ...
A: Your plugs sound fine. If your bike was running lean it would run hotter, but is doesnt sound lean. ...
|
| voltage regulator prblem? or what else? | 7/12/2009 |
Q: 2003 Ultra Classic, 12,000 miles. I bought it last summer. Stage one but no other engine work. Above ...
A: What you need to do is unplug the regulator. Now you have two wires from the stator. Go from one ...
|
| 73 shovelhead | 7/12/2009 |
Q: how do i cheak if my primary oiler is working correctly.what would be the cause of cylender num. 2 ...
A: To check the oiler disconnect the oil line going to the primary from the oil pump and run the bike ...
|
| voltage regulator prblem? or what else? | 7/11/2009 |
Q: 2003 Ultra Classic, 12,000 miles. I bought it last summer. Stage one but no other engine work. Above ...
A: What you need to do is test your stator. Do a OHMs test on both wires and then a AC voltage test on ...
|
| harley repair | 7/11/2009 |
Q: im changing the primary gasket on 84 sportster,how do i remove the cover,then replace the gasket?
A: First you need to drain the primary oil. Next, adjust clutch cable so there is some slack in it. ...
|
| 1993 FLHR completely dies for 15 seconds | 7/11/2009 |
Q: Mike, I have a 1993 FLHR with the hard bags and all. My bike dies on me intermittenly, one ...
A: Since your lights and everything are going off then you are losing power. I would start by checking ...
|
| 2005 Road King Classic (FLHRCI) Clutch Adjustment | 7/10/2009 |
Q: I just purchased a 2005 Road King Classic with 12,700 miles. The clutch seems a little sloppy, takes ...
A: Check your clutch lever, you should have about 1/8 inch play in it. If you need to adjust it follow ...
|
| Open belt drive | 7/10/2009 |
Q: I know you work on harleys but i have a 113 S&S on a bourget.What is the advantages and or ...
A: Putting a open drive belt on is cosmetic. Some riders liek the looks of them. They dont really give ...
|
| Carb problems | 7/9/2009 |
Q: I have a 1986 Sportster that I just purchased and it's basically bone stock. It does have 1 3/4" ...
A: Since you said your biek is stock and probably have a stock carb, you dont have a idle jet. the ...
|
| '94 Ultra Classic Tour Glide | 7/9/2009 |
Q: I am the second owner of this great bike and just put 5000 miles on it in 10 weeks, it now has ...
A: get under the bike and look straight up where the oil is dripping and look to see where its coming ...
|
| fork cups | 7/9/2009 |
Q: we need direction how to install fork cups in a 1999 harley we are trying to change the triple tree ...
A: First you have to jack the bike up and remove the front wheel, fender, brake caliber, forks and ...
|
| road king handlebars | 7/8/2009 |
Q: I have a 08 road king and want to change handlebars. I have not done any mechanical work in years ...
A: Its pretty cut and dry. remove the controls. If the left frip is to tight or glued on you will have ...
|
| 68 xlh sportster | 7/8/2009 |
Q: Mike, I recently picked up a 68 xlh. Have been riding it and noticed I am getting a noise from the ...
A: Check yoru chain adjustment on the primary. If its to loose it will make a noise. If that doesnt ...
|
| 2007 Nightster Engine Knock/Cutout | 7/8/2009 |
Q: My wife's 2007 Nightster has had an ongoing issue and a new one. Currently approximately 4,000 ...
A: Your knocking is probably from a lifter bleeding down. It should hold pressure, but sometimes they ...
|
| 49 Panhead Kick Starting Issues | 7/8/2009 |
Q: Mike, I have a 49 Panhead chopper with an S&S carb (I did not build the motor... so I am not certain ...
A: try starting it by, with the ignition off, twist the throttle a couple of times and kick it over. ...
|
| 1999 DYNA LOWRIDER | 7/8/2009 |
Q: WHEN I FIST START MY BIKE NO MATTER HOW LONG I LET IT WARM UP IT WILL SPIT FART AND BACKFIRE FOR THE ...
A: It sounds like you have a intake leak and once the motor warms up the leak seals from the expanding ...
|
| carb problems | 7/4/2009 |
Q: Hey Mike! I have a 88ci S&S engine with a super e carb. i know you said you only know about harleys ...
A: Your plugs are fouling so it can be a couple of things. I would doa OHMs test on the coil and plug ...
|
| Throttle cables | 7/3/2009 |
Q: Mike, I recently bought a S&S Super E for 03' Softail. I had a stock CV carb before hand. The ...
A: S&S cam out with housing for the cables which will work with the stock cables, so you didnt have to ...
|
| morelli fuel injection | 7/2/2009 |
Q: I have a '97 road king with the morelli fuel injection which is giving me fits. It doesn't idle ...
A: I use a different approach to remapping the ECM. You should be able to remapp your bike. If you go ...
|
| 883 Iron handlebar alignment | 7/2/2009 |
Q: New '09 883 Iron and the handlebars are slightly out of alignment (not square to the fork). This ...
A: If it were me I would take it back to the dealer and have them do it, but if you want to do it ...
|
| bad Coils or faulty electronic ignition? | 7/2/2009 |
Q: Sir, I read for over an hour on your previous answers but didn't find a clue about this 1989 1200 ...
A: the ignition might not be orgional, since you can put rivits back in after removing them. Since your ...
|
| Carb | 7/2/2009 |
Q: I have a 1981 low rider that was handed down to me by my late brother. I have started the bike last ...
A: You should be able to rebuild the carb, but if you cant, the first part number you gave me is the ...
|
| '04 Ultra Classic Voltage Regulator | 7/1/2009 |
Q: I'm going to piggy-back onto the question about the voltage regulator. My Ultra Classic has 39,000 ...
A: Any time you have a regulator problem you should test the stator. It might have caused the problem. ...
|
| 01 flhri electrical | 7/1/2009 |
Q: I have a 01 flhri. I'm having a problem with my headlight, tail lights, brakes lights and fuel ...
A: On your bike, you dont hae relays, you have fuses. You have a short in the lighting system. What you ...
|
| Electrical/Idling problem | 7/1/2009 |
Q: 1985 FLT Evo Problem: Starts fine, runs awesome, when dry and no lights are used. It seems when i ...
A: It sounds like the lighting is robbing the ignition of voltage causing the bike to stall. I would do ...
|
| pipes | 7/1/2009 |
Q: I have an 08 ultra. I have stock pipes on now.I want sum rumble not real loud.What kind of pipes can ...
A: your biek came from the factory a little lean. Chenging the pipes with free flowing pipes, which ...
|
| 1985 FXRS | 6/30/2009 |
Q: Replaced the starter and starter solenoid on my 85 FXRS Low Glide. When connecting the battery, the ...
A: Disconnect the cable from the starter and connect the wires to the solenoid. Only one wire, the one ...
|
| Starter winding out not engaging | 6/30/2009 |
Q: My starter on my 1996 FXD all of a sudden just started winding out and will not engage I pulled the ...
A: Check the teeth on the gear of the jackshaft and the teeth on the clutch basket to make sure they ...
|
| battery replacement | 6/30/2009 |
Q: What is the trick to getting the battery out of a 2004 883 sportster?
A: There is not trick, they are just a tight fit and a real pain. Remove the top cover and front cover. ...
|
| Shutting down around 50mph | 6/30/2009 |
Q: I have a 2000 Fatboy 1450cc -6500miles. most times i reach around 50mph the engine shuts down.it ...
A: Since your bike has a choke, then its carberated. Since you are loosing power, like the key was shut ...
|
| mixture screw/jetting. | 6/30/2009 |
Q: Mario from OZ here.Mike could you please clear something for me on what dose the mixture screw do ...
A: When turning the mixture screw inward leans the carb and outward richens the carb. One thing to ...
|
| Can't find neutral. | 6/29/2009 |
Q: I have a revtech 6 speed transmission. It's not that I have a hard time finding neutral while idle, ...
A: Alot of harleys, even with aftermarket trans, have trouble finding netural. Ont he shifter cam there ...
|
| Dead start | 6/29/2009 |
Q: I was riding all day in 90 degree weather and for about 30 minutes in 100+ degree( Lake ...
A: You have a short in the main wiring. Possibly in the key switch. About the only thing you can do is ...
|
| transmission leak | 6/29/2009 |
Q: i have a 76 fx 1200 shovelhead with a 4 speed and it leaks trany fluid around the sprocket. my ...
A: There is a seal betweent he mainshaft and 4th gear you probably need to replace. Its inside 4th gear ...
|
| points setting | 6/29/2009 |
Q: Im a new Harley owner, and the Harley I have has been converted from electronic ignition to a points ...
A: Just set the points on the small lobe, dont worry about setting it on the wide lobe. They should be ...
|
| my 07 ultra miss's at certian rpm | 6/27/2009 |
Q: any idea what would cause my 96" to miss at 2000-2200 rpm? some times it will miss when taking off. ...
A: It sounds like one of your sensers is cutting out. The Problem is going to be which one. There are ...
|
| 1986 harley electrs glide | 6/27/2009 |
Q: upon start up for the first time this year the motor began pumping oil out of the cam breather line ...
A: Your problem is the bottom end is full of oil and when you try to start it, the oil going in and the ...
|
| my dad let it sit | 6/26/2009 |
Q: my father got ill and let his motorcycle sit for a little less than a year and I want to fix it to ...
A: I would drain the gas and put fresh in. Cherge the battery and see if the bike will start. If it ...
|
| 2005 Sportster XL1200C Carb-Jetting | 6/26/2009 |
Q: After market 2.5" Snub Nose Santee exhaust. Do you know the original carb jet settings for my make ...
A: Your stock jets should be a 45 and a 150. What you need to do to jet your carb is go for a ride and ...
|
| primary drive chain replacment | 6/26/2009 |
Q: i have a 1998 harley fat boy that has the primary chain strechet to the limit it has 25k miles on ...
A: At 25,000 miles you should be fine. they should last 80,000 to 100,000 miles, no problem. If you ...
|
| oil leaking through the air filter | 6/25/2009 |
Q: I have a softail Harley that I replaced the original engine with approximately a 2003 S&S 107, ...
A: What is happening is, since the bike has been sitting, is oil weeped into the bottom end. The oil ...
|
| bent pushrods | 6/25/2009 |
Q: Bud I've started me bike after adjusting the pushrods,i let her warm up with the choke on.When i ...
A: When you adjust hydrolic pushrod and you have some play in it, it takes a couple of minutes for it ...
|
| hydraulic or solids | 6/24/2009 |
Q: My 92 fxd custom had leaking rocker covers,after replacing i checked the push rod clearance as you ...
A: If you have solid lifters they do not bleed. they are made solid. Always adjust cold, never hot. It ...
|
| Deceleration popping | 6/23/2009 |
Q: I have a 2000 FLHTC with a carb. I have a deceleration popping problem that I can't cure. When I ...
A: Your problem is the exhaust is loading up durning decell causing the popping, which is caused by the ...
|
| no oil to top end | 6/23/2009 |
Q: I have a 96 sportster 883 with a 1200 kit. Blew a head gasket and noticed the head bolts were loose. ...
A: It takes quit a while to get alot of oil to the top end and you might not be giving it enough time. ...
|
| Throttle Cable Adjustment | 6/22/2009 |
Q: Mr. Wells, I know your expertise is on Harley's, but this is a generic question that I thought you ...
A: Most throttle cables have an adjuster on them. You would have to follow the cable and locate the ...
|
| 1977 Harley Davidson super glide | 6/22/2009 |
Q: Do you have a diagram or step by step instruction on how to replace the front master cylinders on a ...
A: I dont have any diagrams to send. You can get one in the harley service manual. In order to replace ...
|
| karata belt drive | 6/7/2009 |
Q: I have a 1984 1/2 FXRDG.2 questions:1/I installed a Karata belt drive(dry primary) and the bike ...
A: Couple of things to check. Make sure you have good connections on the battery, both positive and ...
|
| 95 sportster | 6/7/2009 |
Q: I have a 1200 converted from 883 95 sportster. i changed oil and now i have a rattle or chatter ...
A: The only thing on the left side of the bike that can make a noise would be either your primary ...
|
| 95 sportster | 6/7/2009 |
Q: I have a 1200 converted from 883 95 sportster. i changed oil and now i have a rattle or chatter ...
A: When you say you replaced the top end seals, which seals are you referring to? Where does the noise ...
|
| Draining gas tank | 6/7/2009 |
Q: Thank You
A: Your fuel is pretty old so I would dump it. Since you never said if its carberated or not, if ...
|
| poping out deceleration | 6/7/2009 |
Q: ANSWER: Pull your plugs and let me know wht color they are Mike ---------- FOLLOW-UP ----------my ...
A: With the setup you have, you are probably sucking air through the exhaust, which will cause the ...
|
| 1998 Harley Road King | 6/6/2009 |
Q: How do I change the primary oil in my 1998 Road King?
A: Look under the primary at the back and you will see the drain plug. It should be a allen screw. ...
|
| voltage regulator | 6/6/2009 |
Q: Could you please advise me as to the best way to test a voltage regulator on a harley fatboy. ...
A: There is no test for the voltage regulator. What you need to do is test the stator. If the stator ...
|
| what oil weight on my S&S motor | 6/6/2009 |
Q: I just bought my bike last night and had to change the starter. Was wondering what weight oil I use ...
A: I am going a assunm you are talking about the primary. You can use any oil that is made for the ...
|
| 83 shovel | 6/5/2009 |
Q: What do you torque the exhaust header bolts and what do you use to keep the exhaust ports from ...
A: There is not much you can do about the leaks, unless you add thicker gaskets. the problem is the ...
|
| Sportster Starter problem | 6/5/2009 |
Q: OK. I removed the primary, cleaned the clutch plates, replaced it. Removed the Cam cover cleaned it ...
A: Check the starter gear to make sure its contacting the gear on the clutch basket. Also, check the ...
|
| top end noise bad rattle | 6/5/2009 |
Q: on 5/9/ 2004 Dewayne asked you a long question about his 84 xlx rattling after fixing a broken wrist ...
A: the more loose the pushrods are, in solids, the more they rattle. You are going to get some lifter ...
|
| No Start | 6/4/2009 |
Q: I have bike that was customized and chopped in 2001. The engine is an 86-inch shovelhead. The ...
A: Your clicking is the starter relay. There are two things that can be wrong. One is the relay itself, ...
|
| Changing the levers on a 2000 1200c sportster | 6/4/2009 |
Q: Could you give me any advice on changing my levers(clutch & front brake), purchased some cool ...
A: Both levers have a pin going through them, with a clip on the backside of the pin. Remove the clip. ...
|
| sputtering and backfiring thru intake | 6/3/2009 |
Q: have a 2005 softail classic fuel injected with 18000 miles and bone stock. bike is running extremly ...
A: There are a couple of things that can cause the above problem. Coil is bad, plug wires are bad, and ...
|
| brake light problem | 6/3/2009 |
Q: I recently change the bars on my 100th anniversary 883 sportster and my brake light was stuck on, i ...
A: Check both switches to see if you have power to them. There should be two wires to each. one hot and ...
|
| vibration | 6/3/2009 |
Q: I have a 2007 streetglide that I had a new custom built 103 motor put in along with chrome front ...
A: First thing you need to do is check your tires. Since that back one is bad, go ahead and replace it. ...
|
| 1994 Fatboy Carb Issue from 2 year storage | 6/2/2009 |
Q: I have a 1994 Stock fatboy thst was stored for 2 years with fuel in tank and fuel shutoff turned ...
A: Those diaphram are a pain to get in. Over time they get streached and it seems you have to much. If ...
|
| base cylinder leak | 6/2/2009 |
Q: i have small leak( a spot of oil) on the rear cylinder on the clutch side, this has been going on ...
A: Over time it is only going to be worse. So you need to repair it. If it were me, I would have both ...
|
| timing? | 6/2/2009 |
Q: hey thanks for all the great advice on oil and clutch fluid , i do have another problem with my 94 ...
A: Are you talking about he whole cam cover? If you are then you need to remove it if you slide it out. ...
|
| lighting problem | 6/1/2009 |
Q: I have a 2004 flht standard I noticed yesterday that my rear brake and runing lights were not ...
A: Since the TSSM was unplugged then you have a short in the wiring. What you need to do is start ...
|
| 86 Sportster idle issues | 6/1/2009 |
Q: I need some help. I have a 1986 Sportster that sat for 11 years, 883 to 1200 conversion was done - ...
A: It sounds like you have a carb problem. With a bike sitting that long vent and vaccumn holes in the ...
|
| steering | 6/1/2009 |
Q:
A: In order the remove the steering lock the whole front end has to come off. It cant be removed unless ...
|
| Head Gasket | 5/31/2009 |
Q: I have a 2006 FXDBI. I'm getting black oil like stuff on my heads about half way down. Would this ...
A: what you need to do is clean it off and then let the bike idle so you can find the problem. If you ...
|
| petcock valve | 5/31/2009 |
Q: First I want to thank you in advance with any help you can give me. My boyfriend has been busting ...
A: First thing you need to do is check to make sure the vaccumn line if hooked to the percock as well ...
|
| shovelhead tap | 5/31/2009 |
Q: I just purchased a 1981 flt and was wondering just how much valvetrain noise is normal, mine seems ...
A: If you ahve to much tapping one of the hydrolic units might not be pumping all the way. I would go ...
|
| 98 fatboy carborated and stalling as if out of fuel | 5/31/2009 |
Q: I have 98 hd fatboy - at times when at a stop ready to hit first gear , or first starting up it acts ...
A: First, remove the hose from the carb and see if you get a as flow through the hose. If you dont get ...
|
| 89 flstc | 5/30/2009 |
Q: I had the rotor and stator replaced and the bike ran like a champ for one day.Three weeks later when ...
A: the coil should have 3.2 OHms on the primary side. Should be around 15,000 on the seconday side. ...
|
| 2007 nightster starting issues | 5/30/2009 |
Q: about a year ago i was riding stoped to get gas and my bike wouldn't start after a while it did. ...
A: If you are running that kind of voltage, it is not your charging system. After checking the cables ...
|
| electrical issues with a 91 sporty | 5/30/2009 |
Q: Hey Mike, MY buddies 91 sporty 1200 was running good, but if he stopped, his battery would be dead ...
A: First, you need to test the stator, which is what you have. Do a OHMs test from ground to each wire ...
|
| 130 X16 to 150 X 18 | 5/29/2009 |
Q: is it possible to mount a 18 X150 rear tire on my '02 road king? Will it fit on a '06 road king ...
A: In order to mount that tire you would have to make some changes. You dont have enough room for the ...
|
| 2002 Roadking bogs down | 5/28/2009 |
Q: What could be making my bike bog down when you give it gas running about 60 or 65mph in 5th gear? If ...
A: It sounds like either your throttle position senser is going bad or the bike needs to be remapped. ...
|
| Stuck Throttle | 5/28/2009 |
Q: Good morning. I just got my bike last night and it has been sitting for the past 6 months, and now ...
A: First you need to determine if its the carb or the cables. Go to the adjusters on the cables, close ...
|
| fluids | 5/27/2009 |
Q: how much fluid does a tranny hold in a 94 1200 sportster and how much should you use in oil for the ...
A: Type of fluids is going to be a personnel preference. If you ask a hundred people what fluid to use, ...
|
| Harley shovelhead Head Torgue | 5/27/2009 |
Q: Hell, How do I get a torque wrench in to torque the head bolts on a 78 1200 shovelhead. Is there a ...
A: Orgionally the shovel head bolts were not torqued. Just tighten them down really tight. When you get ...
|
| rocker box covers | 5/27/2009 |
Q: I want to take off my rocker box covers and have them chrome, the motor is a 1960/900 sportster. my ...
A: In order to remove the rocker boxes you have to remove the heads so you can get them off. You would ...
|
| Slip-ons for a 2009 Heritage Softail Classic | 5/26/2009 |
Q: I have a friend that recently purchased his first Harley and admits that he was so happy just to ...
A: Either exhaust is really good. He should put on what he likes. He might want to listen to other ...
|
| Sportster not shifting | 5/26/2009 |
Q: I have an 07 Sportster 1200 with 15000 miles. All of the service has been done at the suggested ...
A: Your going to have to remove the primary cover and do an inspection on the trans. You may have to ...
|
| stator kit | 5/26/2009 |
Q: I picked up a stator kit for my fxs.It,s non molded.It come with the mounting screws and four 4inch ...
A: I am not sure why it came with zip ties. They are not used inside the primary, unless you have a ...
|
| S&S carb set up | 5/26/2009 |
Q: I have a 1995 Dyna FXD with an S&S super carb and I'm getting a miss when I accelerate. I check the ...
A: Your sooty plugs can be caused by two different problems. First, is you coil or plug wires are weak. ...
|
| Speedometer cable attach | 5/25/2009 |
Q: I'm replacing the forks on '94 Heritage Softail. The speedo cable to front wheel attach point has ...
A: Use some pliers and the cable will screw out of the drive unit. you dont really need to take it out ...
|
| Why did the '81 shovelhead ship with offset cylinder timings? | 5/25/2009 |
Q: It seems odd that they wouldn't have been equally calibrated... it's not vital for a repair, but it ...
A: Harley have made pretty much the same setup since they starter making the v-twin. Both cylinder rods ...
|
| exaust | 5/25/2009 |
Q: what can I do to make my exaust louder on my 06 1200L sportster? It has the stock pipes and ...
A: Your best bet is to buy new mufflers. Drilling holes will give you a littel more noise, but it ...
|
| 78' superglide doesnt start | 5/24/2009 |
Q: i have a 1978 superglide and out of no where it just stopped turning over, i took off the cover that ...
A: What you need to do is take a test light and pushing the starter button and see if there is power ...
|
| Clutch cable | 5/24/2009 |
Q: We need idiot proof instructions how to change the clutch cable on a 99 sportster. We took the cover ...
A: Looking at the arm that it is attached to you will see 3 bolts around it. remove the bolts and the ...
|
| changing back tire. | 5/24/2009 |
Q: I WANT TO CHANGED THE BACK TIRE ON MY 2003 IRON HORSE CHOPPER. WHERE DO I START?
A: You have to jack up the bike so there is no weight on the wheel. remove the axle and jack up the ...
|
| brakes | 5/24/2009 |
Q: how do you change rear brake pads on a 2001 sportster 12oo custom
A: There are two pins on the caliber, close to the top, which holds the brake pads in. remove the pins ...
|
| Harley intake seal leak | 5/24/2009 |
Q: It doesn't seem to matter what we do we still have the leak. Replaced seals X 2 intake and head ...
A: the best way to see if you have intake leak is to spray a little carb cleaner around the intake. If ...
|
| 94 fatboy harley | 5/23/2009 |
Q: my bike was work,n fine the pipes have been blue since i got the bike.i went out in the morn the ...
A: I assumed you had points since you stated that you had a condenser. Do you have points or electronic ...
|
| clutch wont fully engage | 5/23/2009 |
Q: when i pull in the clutch and put it in first the bike lunges forward and stalls i have tried to ...
A: Check the adjustment on the clutch. It is not releasing all the way. Loosen the clutch cable so ...
|
| Why did the '81 shovelhead ship with offset cylinder timings? | 5/23/2009 |
Q: It seems odd that they wouldn't have been equally calibrated... it's not vital for a repair, but it ...
A: If I understand your question, you what to know why the timing is different on each cylinder? the ...
|
| carb backfire | 5/23/2009 |
Q: I have a 92 soft tail with s&s carb 1 to 2 sec after I shut her down I get a backfire out of the ...
A: I would test the coil and plug wires to make sure they are good. One wire or one side of the coil ...
|
| 94 fatboy harley | 5/23/2009 |
Q: my bike was work,n fine the pipes have been blue since i got the bike.i went out in the morn the ...
A: Your bike cannot jump time, unless you move teh timing plade. It is direct drive off the cam. You ...
|
| Only one cylinder firing | 5/23/2009 |
Q: I have an 1984 Harley sportster. I am only getting one cylinder firing. The cylinder has power ...
A: To check the valve adjustment, rotate the motor so the valve is fully closed or the lifter is all ...
|
| 94 fatboy harley | 5/23/2009 |
Q: my bike was work,n fine the pipes have been blue since i got the bike.i went out in the morn the ...
A: Generally, if you have a bad coil, your bike will run rich and foul plugs. Its because you are not ...
|
| Only one cylinder firing | 5/23/2009 |
Q: I have an 1984 Harley sportster. I am only getting one cylinder firing. The cylinder has power ...
A: Since you have spark and will have fuel, then you need to check your valves to make sure they are ...
|
| Sportster runs bad after warmed up. | 5/22/2009 |
Q: I have a 2005 sportster 1200 with 2700 miles. The bike starts, warms up and runs great for about ...
A: Ok, then take the bike for a ride and when it stops, look downt he throat of the carb and twist the ...
|
| breather oil | 5/22/2009 |
Q: I have a lot of oil coming from the head breathers on a 99 Heritage Softail with 10,000 miles.Mild ...
A: What happened was some oil weeped into the bottom end. When you started the bike the oil in the ...
|
| primary chain case leak | 5/21/2009 |
Q: Hey man , I hava a 1989 HD sportster and when ever i take it for a run it leaks primary chain case ...
A: Its not serious, unless you let the trans and clutch go dry from the leak. Its not real common, but ...
|
| Rear tire | 5/19/2009 |
Q: I know this may sound stupid but I have never worked on my own bike (besides basic stuff) and I want ...
A: Remember, no question is a stupid question. Its all a learning process. First, what you need to do ...
|
| Brake Light stays on | 5/19/2009 |
Q: I have a 1991 FXSTC Harley, 1340 Evo engine. My brake light stays on. I checked the hand control for ...
A: Unplug the wires from the rear switch. That way you can tell if its the front or rear thats the ...
|
| boiling batt | 5/19/2009 |
Q: my bike is a 92 dyna glide coustom.I did the check of the stator as you asked,i get 55-58 ...
A: When you chaeck pole to pole on the stator you should show some resistance, so your stator is ...
|
| Clutch Noise | 5/19/2009 |
Q: Rolling to a stop, pull in clutch at low speed, get a loud whirrrr until bike is stopped. Happens ...
A: The whirling could be a be acouple of things. The nut on the clutch basket is loose or the nut on ...
|
| Ultra Classic | 5/18/2009 |
Q: Cruise control worked intermittantly for a while, now it will not set at all. the cruise light on ...
A: If the light doesnt come on and it doestn work then you have a short. What you are going to have to ...
|
| electric | 5/18/2009 |
Q: i am looking for a wiring diagram for the starter relay on a 1976 sportster.there are five ...
A: In order the get a wiring diagram, you would have to get a service manual for your bike. It would ...
|
| 2009 road glide exhaust upgrades | 5/18/2009 |
Q: To change exhaust to non stock with all the new electronics (throttle, rear cylinder deactivation, ...
A: What I do is connect tot he bike with a computer and change the settings on the ECM without adding ...
|
| boiling battery | 5/17/2009 |
Q: i have a serious problem with my charging system.its over charging and cooking my battery.ive ...
A: If your charging system is putting out 24 volts at 2000 RPM, then you have a charging system ...
|
| mileage | 5/17/2009 |
Q: ANSWER: Are you refering to miles per gallon, number of miles you can go on a tank of gas or how ...
A: That is going to depend on how you take care of the bike. I have seen harleys last 80,000 miles ...
|
| kick start | 5/17/2009 |
Q: 1981 fxef, when cold, 1 or 2 kicks with key off then open enrichener on s&s carb, turn key on and 2 ...
A: By your plugs you are running a little rich or your coil is weak. I would first test the coil and ...
|
| 83 sportster xls | 5/17/2009 |
Q: Is it possible to use a 1979-81 carburetor on an 83 with a vacuum advanced switch if so how would I ...
A: In the top of the carb, towards the back you will see a plug. the screw is located underneith it. ...
|
| sometimes bike will not start when warm | 5/16/2009 |
Q: I have an 87 flhtc, when I ride for awhile and the bike is warm, sometime I have trouble restarting ...
A: Start by checking your battery cables. Make sure they are good, not worn and have a good ground. ...
|
| Votage gauge on my '89 Dresser | 5/15/2009 |
Q: I have a 1989 Harley Dresser. When I turn on my indicators the voltage gauge starts jumping from 9 ...
A: Check the voltage at the battery and see if it jumps around from there. Then you can compare the ...
|
| Rear Brakes | 5/14/2009 |
Q: I have a 94 sporty. I replaced the forward controls with a Excel Components FXR type forward ...
A: The pressure switch would not make the brakes not pump up. It sounds like you still have air in the ...
|
| 85 fxr electrical | 5/14/2009 |
Q: i have a 1985 FXR lower rider (harley of course) ... the other day i went to start the bike and i ...
A: You have a short which is causing the wires to over heat and the clickin you hear is the breaker ...
|
| 94 SPORTSTER | 5/14/2009 |
Q: I installed a new ignition switch, the bike turned on perfectly. The problem came when I put it on ...
A: I cant think of a reason for the new ignition switch causing thing, unless there is a short in the ...
|
| 1996 Harley Davidson 883 Hugger | 5/12/2009 |
Q: A couple questions on a '96 883 Hugger Sportster I recently bought.First,what is the best way to ...
A: There is no really easy way or any quick steps to changing the battery. Its a pain! You dont have ...
|
| runs rough | 5/11/2009 |
Q: 2007 ultra classic 25,000 miles on it was down in Arizona river run warm weather not real hot wanted ...
A: It sounds like one of your sensers is getting ready to fail or you have a blocked fuel injector. The ...
|
| 2004 Sportster 1200 electrical problems | 5/11/2009 |
Q: I recently took my sportster on a road trip and the first time we stopped the battery did not have ...
A: Its either the regulator or the stator. You would have to test the stator to see what the problem ...
|
| electrical | 5/11/2009 |
Q: I was on a ride last weekend and my bike just died. Battery was dead. We thought the bike had ...
A: What you need to do is test the stator. Charge the battery. unplug the regulator. Do a OHMs test ont ...
|
| 02' 1200 sportster | 5/10/2009 |
Q: Just bought 02'1200c that had not been run for 4 years..I replaced the battery, changed the oil, new ...
A: Since you say the diaphram is in correct and it doesnt slide when giving it throttle then one of the ...
|
| 98 fatboy stalling | 5/10/2009 |
Q: I have a 98 fatboy with the evo 1340 and i was riding today and the bike just shut down and would ...
A: First thing I would do is let the bike warm up and go for a short ride so it will quit running. Pull ...
|
| primary cover removal | 5/9/2009 |
Q: How would I remove the primary cover from a 1987 Sportster? (without breaking anything) Please help ...
A: Remove the derby cover on the back of the primary cover. Behind it you will find a spring and nut. ...
|
| powder coat | 5/8/2009 |
Q: I was thinking of powder coating my motor/engine instead of doing the all chrome thing that we ...
A: You can powder coat anything metal. The only difference is if you are doing a exhaust system, you ...
|
| rocker boxes | 5/8/2009 |
Q: Are the heads under the rocker boxes,when i remove rocker arms do i remove push rods do i change the ...
A: Yes the heads are under the rocker boxes. You donet have to remove the rocker arms from the lower ...
|
| Dyna kickstand | 5/8/2009 |
Q: Mike: How do you replace the kickstand on a 2000 Dyna FXDL? I can see a pivot and a button screw but ...
A: Remove the bolt at the top of the stand which hold it on. The stand willslide out and remove the ...
|
| Adjust clutch on 2007 883 sporster | 5/8/2009 |
Q: I tried to adjust my clutch. It seemed to work except when i am in fifth gear, going about 40 and i ...
A: Loosen the adjuster onthe cable so you have some slack in it. Open the derby cover on the primary ...
|
| triple tree and bar alignment | 5/8/2009 |
Q: I have an 07 fatboy with aftermarket Burleigh bars. When riding the bike the bars and top tree don't ...
A: The forks align the top triple trees with the bottom. If your bars are not straight, then its either ...
|
| 69 sporty timing | 5/7/2009 |
Q: I have been reading past questions on timing, they all seem to be for timing on a side mounted ...
A: What you want to do is install the plug or hold your finger over the hole. Set up the timing light ...
|
| Oil Leak 1974 Ironhead xlch | 5/7/2009 |
Q: Bare with me as I am a novice. I just came upon a 1974 Sportster that hasn't ran in a year. ...
A: The front one with the cross is the fill point and the other is the plug to remove to adjust the ...
|
| '03 HD Fatboy clutch shaft throw out baring | 5/6/2009 |
Q: Mike, Per your suggestion last week, I replaced the throw out baring yesterday because my clutch ...
A: you need to check the rod ends. they are hardened. If the throwout bearing went out and the rod ends ...
|
| 883 Sportster Won't Start | 5/6/2009 |
Q: I own a 2000 883 Custom. Owned it for about 7 years. Everything worked fine until about 6 months ...
A: you probably have a short int eh electrical system. What you need to do is start by checking with a ...
|
| 5-speed in 4-speed frame | 5/6/2009 |
Q: will a 5-speed from a 87 softail be made to fit the 4-speed frame of a 79 fxs?
A: It will fit the frame, but the inner primary wont line up and the clutch basket wont work either, so ...
|
| generator on 71 sporty | 5/5/2009 |
Q: i took of the 12 volt generator reinstalled but forgot to mark the wires one is red and one is ...
A: The two wire colors on the generator should be red and gray, so somebody has changed the wires. Look ...
|
| idle cable on '88 Harley lowrider | 5/4/2009 |
Q: I need to replace the throttle cable due to a brake in the elbow & was wondering how I go about ...
A: Close tot he throttle is the cable adjuster. Loosen the locknut and turn the cable so it shorter. Do ...
|
| Front end wobble | 5/4/2009 |
Q: 2004 lowered Softail Standard. Just started, horrible wobbling at 55 + mph. Feels like the wheel is ...
A: Even though the tire is not that old, it might have a bad spot in it or is worn in a spot. the other ...
|
| Repair of timing hole | 5/4/2009 |
Q: Mike, I musy be the only guy to ever have done this. When timing my 90 FLSTC, the plastic insert ...
A: That is the first time I have ever heard of this happening. Heres what you do. Find a dealer who ...
|
| Brake lights | 5/3/2009 |
Q: I have a 2006 harley davidson 1200 sportster. My back light is not coming on. I've already changed ...
A: Look on the old bulb and you will see the bulb number and that is the one you need. On the testing ...
|
| shovelhead hard to start cold | 5/3/2009 |
Q: I have a 76 74" shovel.It is kick only with a dyna ignition and a super b.I built it 6 years ago, ...
A: Couple ot things. If you have solid pushrods, make sure they are not to tight. Check your timing, to ...
|
| Brake lights | 5/2/2009 |
Q: I have a 2006 harley davidson 1200 sportster. My back light is not coming on. I've already changed ...
A: If you have power to the bulb connection, where the bulb plugs in, then its not the wiring. Make ...
|
| caburator spitting | 5/2/2009 |
Q: after top end overhaul, bike started spitting once and awhile out of caburator when riding, not ...
A: If the bike rean without spitting before the top end job then it is either a leaking intake or ...
|
| 1999 Ultra | 5/2/2009 |
Q: I was wondering if you could tell me where to drain and change the oil in the block trans and ...
A: Look under the bike from the right. Close to you, on the oil pan and to the center is the trans ...
|
| oil leaking from exhaust of cylinder head where the header conects | 5/2/2009 |
Q: I have a 1979 80 ci shovel and noticed oil leaking on my battery cover and right pant leg last ...
A: It could be either the seal ont he back of the inner primary to the trans shaft or the main seal on ...
|
| gear ratio | 5/1/2009 |
Q: I have a 2004 FSTBI. I am interested in changing the gear ratio. I weigh 175 and rarely ride anyone, ...
A: You can can add either a tooth to to the pulley on the trans or go smaller on the rear pulley, which ...
|
| !998 Road King speratic starting | 5/1/2009 |
Q: I have 1998 Road King with fuel injection. Sometimes I can't pull my finger off the start button ...
A: It sounds like when you are trying to start it that the fuel injectors are not opening up enough or ...
|
| adjustin my clutch | 4/30/2009 |
Q: hey mike I have a harley chopper with a rachet top trany. I need a little help readjustin my clutch. ...
A: For the springs adjustment, its 1 3/32 space fromt he front plate to the plate the goes against the ...
|
| no lights or power to starter | 4/30/2009 |
Q: I have a 1994 flhtcu. I was riding everything was fine. I stopped turned it off and it would not ...
A: Check to make sure your battery connections are clean and tight, especially the ground. Starting at ...
|
| electrical problem | 4/30/2009 |
Q: I have a 1990 FLTCU,and in 1994 it was converted to a Trike by Lehman. The problem is the volt meter ...
A: Do your voltage at the battery with a meter. Sometimes the volt meter on the bike might be off. ...
|
| oil leak 94 sportster | 4/30/2009 |
Q: i recently bought a 94 sportster 883 i have done some work to it as the bike had been sitting for 5 ...
A: Yes, you wuold have to remove the rocker boxes and cylinder to replace. One thing you want to ...
|
| dragging sound when attempting to start... | 4/30/2009 |
Q: I have a 1985 fxwg wide glide that will not turn over when attempting to use the electric starter, ...
A: Make sure you have a really good ground. If it still drags then your starter soleniod is either bad ...
|
| Oil plug - allen screw 4/19/09 | 4/29/2009 |
Q: I pulled out the same allan screw as Ray did in his question about finding the oil drain plug ...
A: The trans plug is close tot he right side of the pan and the motor oil plug is close to the front ...
|
| harley voltage regulator | 4/29/2009 |
Q: I have a 01 FXST and it completely cut out while starting, I cannot get any juice anywhere.. no ...
A: Unplug the regulator and try to start it. If it starts then you have a short in the chargig system. ...
|
| 95 Evo Starter (FLHTCUI) | 4/29/2009 |
Q: How do I remove the starter from my 95 FLHTCUI?
A: First, disconnect the battery. Then you have to drain the primary and remove the cover. remove the ...
|
| Harley Charging Problem | 4/24/2009 |
Q: I live in NY my brother in New Orleans told me about you and said you may be able to help me? Thank ...
A: You really need to try a volt meter so you can see what the voltage is, but if you can its probably ...
|
| harley push rod seals | 4/24/2009 |
Q: how to put pushrod seals in 1982 fxr shovelhead
A: First, remove the clips ont he covers and slide them up and out of the way. Now loosen the locknut ...
|
| harley repair | 4/23/2009 |
Q: how to replace carburetor on my 2002 1200 sportster ANSWER: What are you replacing it with? Mike ...
A: The rubber seal should just pull off, but you can get it off with a screwdriver. The cable adjusters ...
|
| harley repair | 4/23/2009 |
Q: how to replace carburetor on my 2002 1200 sportster ANSWER: What are you replacing it with? Mike ...
A: Remove the air cleaner and backplate. The carb will slip off the rubber seal. At he throttle loosen ...
|
| 1988 Sportster Clutch Adjustment | 4/21/2009 |
Q: I have a 1988 HD Sportster 1200. I have adjusted the clutch using the service manual. The clutch ...
A: Remove the derby cover and under it you will see a spring and nut. remove the nut. There is another ...
|
| starter 2002 harley | 4/21/2009 |
Q: I need to know what i have to do to change the starter on my 2002 harley softtail deuce
A: First, you need to remove the primary cover, with the oil drained and then the motor sprocket and ...
|
| mls seepage cold | 4/21/2009 |
Q: I have httc heads & pistons(95")(10.5/1Comp.)60G andrews gear drive cams.Twin tec, 42 mikuni.ALL NEW ...
A: What is happening is as the motor warms up it expands and stop the leaks. Over time they will get ...
|
| 1 5/8th Belt Drive kit. Good or Bad choice? | 4/20/2009 |
Q: I have alot of friends that tell me not to get a belt drive for my 87 FLHTC. The one I have been ...
A: Harley made the primary belt drive for a few years, but went back to chain drive, due to the belt ...
|
| 2009 FXSTB Backfire | 4/20/2009 |
Q: I bought a 2009 Softail Night Train (Stock) recently, put a couple of miles on it (15 total on the ...
A: What is happening is the cylinder is loading up with fuel and when you try to start it you are ...
|
| 4 Speed leaks from drive shaft | 4/20/2009 |
Q: This was supposedly rebuilt, at least the guy before me had receipts for it. I have replaced seals ...
A: Check the race that the seal rides against. It might have a burr on it or a flat spot rubbed on it ...
|
| Sportster Rocker Box | 4/20/2009 |
Q: I have a leak that has gotten progressively worse between the lower rocker box and the head. I've ...
A: You dont have to remove the rocker arms to remove the lower box. You will however have to remove the ...
|
| IRONHEAD 72 CLUTCH AJUSTMENT | 4/19/2009 |
Q: I REBUILT MY CLUTCH.NEW FRICTION AND METAL PLATES. FOLLOWED THE BOOK TO A TEE.AND CAN'T GET CLUTCH ...
A: Loosen the adjuster and the cable so there is alot of slack in it. Push the cable back towards the ...
|
| 1999 Heritage Softail Classic | 4/19/2009 |
Q: I'm only getting 20 MPG and I think it could be a choke adjustment, when I throttle it kind of feels ...
A: Since your plugs are black you are either running to rich or you have bad coil or plug wires. I ...
|
| oil change | 4/18/2009 |
Q: This may sound dumb but I can't seem to find the engine oil drain plug on my 2001 Ultra Glide. I ...
A: Look under the trans and you will see the oil pan. Fromt he right side close to centered of the pan ...
|
| 1987 FLHTC clutch adjustment | 4/18/2009 |
Q: Would you have a simple to follow set of instructions on how to adjust the clutch on my 87 FLHTC. ...
A: If it slips then it to tight. Go to the cable and at the adjuster loosen it so there is slack in the ...
|
| exhausts-electronics. | 4/18/2009 |
Q: I have a 2004 softail Heritage and I want to change my standard exhausts because I want a nicer ...
A: What happens is when you change pipes to a more free flowing pipe, you lean the bike somewhat. you ...
|
| Turn signals & Starter | 4/18/2009 |
Q: My bike is a 1974 FXE lowrider, The starter will stay ingaged when starting and when it,s running, ...
A: Your starter problem is either low voltage or a bad starter solenoid. Check your battery to make ...
|
| Triple Tree assembly | 4/17/2009 |
Q: I own a 97 sportster 883. It was wrecked when i bought it. I need to know exact order on how to ...
A: On the lower tree install the dust shield and then the tapered bearing. Make sure you grease both ...
|
| 2005 night train fluids change | 4/16/2009 |
Q: I want to do a primary,engine, and tranny fluid change.what plugs under the bike are for the oil ...
A: the primary drain is located at the rear of the primary, on the bottom. The drain for the trans is ...
|
| exhaust | 4/16/2009 |
Q: I own a 2000 Electra Glide Classic which I had just purchased a set of Rolling Thunder slip ons. I ...
A: You can remove the baffles for more noise, but, you will lean the bike out by doing that and you ...
|
| starting the motor | 4/16/2009 |
Q: Went to start the bike for the first time [1985 fxrs,evo] this year and the motor just whins real ...
A: First, make sure the battery is good and fully charged. Check the battery cables, on both ends. If ...
|
| no lights | 4/15/2009 |
Q: I have a 1995 FLHTC, i have no headlight, passing lights or tail lights. but i do have dash lights, ...
A: I would start at the headlight and with a test light work your way back to the source of the power. ...
|
| Changing transmission sprocket | 4/15/2009 |
Q: I have a 95 FLSTC with a stock 32 tooth sprocket on the transmission I would like to put on a 34 to ...
A: You can change the trans sprocket, just remember that you will loss some bottom end when you do ...
|
| 2002 Sportster XL1200C | 4/13/2009 |
Q: I have a set of drag bars that I would like to place on my motorcycle. How do I change out the stock ...
A: In order to install the drag bars you need to remove the controls on the old bars. On the right ...
|
| problems in the "primary chain" 1997 heritage | 4/11/2009 |
Q: I'm writing from Italy so, excuse me for my english.Now... about my heritage softail classic ...
A: The jackshaft probably doenst go back because it rides on a bearing in the primary cover, and with ...
|
| '89 Ultra Classic hard to start | 4/11/2009 |
Q: I have an '89 Ultra Classic that is extremely hard to start. You cannot choke it to start it or it ...
A: There are a few things to check. One, make sure your choke is working properly. Two, make sure the ...
|
| engine repair | 4/10/2009 |
Q: hey mike i have a 1980fxs lowrider 80ci. had engine rebuilt have changed out carb to an ss super e ...
A: With that few of miles your compression might b a little low since the rings have not broke in yet. ...
|
| clutch master cylinder | 4/10/2009 |
Q: I do I install a rebuild kit for the clutch master cylinder ANSWER: What year and model? mike ...
A: yes, you would have to bleed the master cylinder. Locate the bleeder valve, pump the clutch lever ...
|
| clutch master cylinder | 4/10/2009 |
Q: I do I install a rebuild kit for the clutch master cylinder ANSWER: What year and model? mike ...
A: remove the clutch lever and pin from the master cylinder. Looking inside you will see a ring clip. ...
|
| Dry Cell Charging | 4/10/2009 |
Q: You spoke about a charging problem in a past question pertaining to checking if a regulator or ...
A: I dont think it was me who said a stator will not charge a dry cell battery. What I said was you ...
|
| 2006 road glide fork | 4/9/2009 |
Q: how do you adjust the bolt on the neck
A: If you are refering to fork nut, loosen the lock nut on the side. With the bike sitting on a jack, ...
|
| twin cam idle | 4/9/2009 |
Q: 99 t/c 95 in. fuel inj. what is the correct idle and how do you adjust it?
A: Your bike should idle at around 950 RPM. To adjust you have to remove the air cleaner and start the ...
|
| 97 harly classic | 4/8/2009 |
Q: removed derby cover and did clutch adj by the book then adjusted freeplay with cable adj. has a ...
A: Your motor mount would not have anything to do with it, but if its bad you should replace it. Your ...
|
| '76 flh oil pump | 4/6/2009 |
Q: ALOHA MIKE, HOPE YOU HAD A GOOD VACATION. A WHILE AGO I WAS DEALING WITH THE BALL CHECK VALVE ON ...
A: You can hone the seat or try to tap a little harder on the ball. i use a old pushrod to hone the ...
|
| Shovel Oil blow by | 4/6/2009 |
Q: Just recently bought a 78 shovel. Oil was coming out of the rear pipe, so I put new rings, had a ...
A: You can check the timing on the breather gear and see if that is the problem. I wouldnt remove the ...
|
| shifter play | 4/6/2009 |
Q: I have a 1998 fxsts that has quite a bit of play in the shifter. I have been told that the primary ...
A: Check the shifter arm on the linkage at the trans. It is probably worn and needs replaced. It is ...
|
| Carborator upgrade for 75 ironhead | 4/6/2009 |
Q: I just purchased a stock 1975 ironhead sporty with a newly rebuilt engine, transmission, clutch, ...
A: There are tow things you can do. Either change carbs, like the S&S, or rejett the CV carb. If the CV ...
|
| Trouble code 2004 XL1200R | 3/22/2009 |
Q: I have a trouble code on my sportster - B0563 - battery voltage high - how do I interpret this into ...
A: It means you might have a short in one of the sensers or a bad TSM. The problem is, as a lay person, ...
|
| master cylinder | 3/22/2009 |
Q: How do I bleed the front master cylinder on my xl 1200 c thanks Bob
A: Look a the brake caliber and you will see a screw on top with a hole is in. That is the bleeder ...
|
| 2007 Ultra Classic | 3/22/2009 |
Q: I wanted to know the steps on how to repair or replace the O Ring seals In the Fuel Tank Coupler ...
A: First, drain the tank. Uncouple the fuel line. Then remove the cover for the tank, so you can get ...
|
| 1976 FLH ignition problems? | 3/21/2009 |
Q: I am attempting to figure out several problems with a 1200 fl. It has a little over 500 hundred ...
A: Start by taking the bike for a ride. Do not go over 2500 RPM. Go for about 5 miles. If the bike bogs ...
|
| front wheel | 3/19/2009 |
Q: i have a95 ultra classic the speedo stopped working so i removed the front wheel then repaired the ...
A: When that small tab breaks that usually means the drive unit is froze up and needs replaced. the ...
|
| HELP--NO POWER | 3/19/2009 |
Q: I HAVE A 1990 ELECTRA GLIDE,I HAVE IT ALL APART TO GET THE BIKE PAINTED,I HAVE ALSO REPLACED THE ...
A: Chec your hot wire going from the battery to the ignition switch with a test light. If you have ...
|
| 1991 Sportster 2 questions | 3/18/2009 |
Q: 91 sporty, 1200cc. First Harley, rode triumphs before...yes, I can hear the oh man......oil ...
A: yes, the drain hose is at the bottom of the tank. Its the short one. There is no drain for the ...
|
| clutch cable | 3/18/2009 |
Q: I need a picture or detailed instruction on the routing of the clutch cable from the handle bars to ...
A: In order the install a clutch cable you first have to remove the derby cover on the primary cover. ...
|
| oil leak on 01 heritage springer | 3/18/2009 |
Q: could you tell me why I have a little oil coming out of my breather and also I have oil weeping on ...
A: You have oil there from the breathers in the heads. When the heads breath a small amount of oil goes ...
|
| sportster sprocket cover | 3/17/2009 |
Q: i need a step by step on installing a sprocket cover on my 2009 sportster, do i need a special tool ...
A: First you have to jack the bike up and then remove the rear axle. Once the axle is out remove the ...
|
| 1971 harley rapido 125 | 3/16/2009 |
Q: hay i got a old rapido125 and i just got it running about a year ago after 20 years of sitting. ...
A: You probably need to rewire the bike to solve the problem. On the key breaking, make sure you are ...
|
| oil cooler | 3/15/2009 |
Q: Hey again Mike. I had asked previously about an oil cooler for a 91 FLHS. I tried to locate one ...
A: I dont think the adapter will fit on your bike. When installing the cooler go from the return line ...
|
| chrome lower fork legs | 3/15/2009 |
Q: just bought a set of lower fork legs for2000 eg need someone to guide me through it step by step ...
A: First you have to jack up the bike so there is no pressure on the forks. Since you have removed the ...
|
| Hard Start Hot | 3/14/2009 |
Q: I have a 2K1 Fatboy w/ 95 overbore, Rinehart 2into1, Mikuni HSR42 (properly jetted), 302cams, and ...
A: It sounds like the problem is the starter drawing to much voltage. When this happens it kills the ...
|
| leekin mass amounts of oil after replacing all my push rods | 3/13/2009 |
Q: after replacing push rods on my 95 dyna conv I have a serious oil leek that I cannot seem to find ...
A: there could be a dozen places for a leak. Clean the bike and let it dry. Spray the motor with ...
|
| oil cooler | 3/13/2009 |
Q: I own a 91 FLHS and live in East Texas. During the summer I will be riding in 95 to 100 degrees ...
A: They still make oil coolers for your year bike. Check with anybody that sells Sifton or Jagg. they ...
|
| How to remove the push rod tubes on a 1977 Harley Davidson FLH Shovelhead | 3/12/2009 |
Q: I have leaking seals and no how to change them but havent removed the tubes before can u tell me how ...
A: You have to remove the pushrods in order the get the covers out and remove the seals. Remove the ...
|
| horn and blinker | 3/11/2009 |
Q: !. When I push my horn button the horn won't turn off. The button isn't sticking so what could ...
A: what you are going to need is a test light. Check the hot wire going to the horn and then at the ...
|
| charging problem | 3/10/2009 |
Q: i have changed the stator 3 voltage regulator and the battery and still have a charging problem at ...
A: Since your stator is testing good then it can be only one of three things. Short in the wire or bad ...
|
| replacing vintage main bearings | 3/10/2009 |
Q: i need to get main bearings for a 1929 bike,is there any thing special about mains; ...
A: If it were me I would stick with the bearing that is called for. If you use another bearing, and it ...
|
| 1983 FXRS Harley | 3/9/2009 |
Q: I am trying to stop a leak at the primary but I replaced the gasket and the leak got worse. I am ...
A: When you install the gasket, make sure the surfaces are clean. You can put some gasket sealer on the ...
|
| harley stalling | 3/8/2009 |
Q: I have the crane ignition single fire hi-4 coil and module,I have spent 1500.00 trying to find the ...
A: Nest thing to check would be to see if you have power at the coil when it shuts off using a test ...
|
| 1964 duo glide electrical regulator or generator | 3/8/2009 |
Q: I have a 6 volt system, but when the bike is runing both the voltage regulator and the generator ...
A: You are not going to have to proper meters to do the testing. Since you are putting out some voltage ...
|
| lowering | 3/8/2009 |
Q: 2004 FLHCI I replaced the stock 16x3 wheels & tires with 18x3.5 wheels & 150/18-70 rear & 140/18-70 ...
A: you can probably lower your bike by the 1" without problem, but adding air to the shocks will do ...
|
| adjustement | 3/7/2009 |
Q: how do i adjuste the clutch on a 1976 harley davidson shovelhead motorcycle.tire turns when its on a ...
A: Go to the adjuster on the cable and loosen it so you have slack in the cable. Now remove the back ...
|
| Changing Slip-ons | 3/7/2009 |
Q: Mike: I have a 2002 FXDL, stage I, and I want to change the stock slip-ons, they are really quite. I ...
A: One thing you have to remember on the new bikes is they come from the factory a little lean to pass ...
|
| jackshaft install | 3/7/2009 |
Q: I'm building a bike from ground up and all components are new. After installing the engine, ...
A: I dont have anyway to send pics on here. The shallow side of the large coupling goes towards the ...
|
| 2005 fatboy | 3/6/2009 |
Q: can you replace a retainer ring on third gear without removing the tranny if so which side.
A: You dont have to pull the trans case out, but you do have to pull the trans gears out. You would ...
|
| Harley 2005 FLSTF Fatboy | 3/6/2009 |
Q: My wife just got me a Harley 2005 FLSTF Fatboy. It has Kuryakyn Pro-R Hypercharger and sreaming ...
A: When you start the bike you need to leave the inrichner about half way out for about 10 minutes or ...
|
| fuel management | 3/6/2009 |
Q: Mike, I have a 1999 Road King EFI with Screamin Eagle slip-ons and an upgraded air cleaner kit. ...
A: What I do is reprogram the ECM with a custom map for your bike. Then you know how its running ...
|
| 2001 roadking claissec | 3/6/2009 |
Q: my 2001 road king has a power commander it was installed in 2002. my bike is runing good but seems ...
A: Check your intake manifold and exhaust for a leak. For the exhaust, you can run your fingers around ...
|
| fuel | 3/6/2009 |
Q: i have a 96 sporty that has a different tank, i am having problems with my bike shutting off when ...
A: You could have a couple of different problems. First, check to see if you have a intake leak. Let ...
|
| Carburetor Adjustment | 3/5/2009 |
Q: I have a 2001 FXDXT with a stock Keirin CV carb. I am a raw rookie at wrenching, but have actually ...
A: You can do that, but you have to give up one for the other. If you want more performance you have to ...
|
| 2000 ultra | 3/5/2009 |
Q: you've probably answered this a hundred times already. I am helping a friend change the oil on a HD ...
A: Look under the bike and you will see the oil pan. Looking from the right side at the middle you will ...
|
| Vibration through pegs | 3/5/2009 |
Q: I have a '05 Softail Standard. I had the frame replaced due to an accident. Ever since then, I have ...
A: I would start by checking all the motor mounts and the swing arm for tightness. Also, check the ...
|
| 1996 FLSTN OIL LEAKING AT CYLINDER BASE GASKET | 3/5/2009 |
Q: HOW HARD IS THIS TO REPAIR MYSELF.
A: Its not that hard. You would have to pull the gas tank, rocker boxes, pushrods, head and cylinder. ...
|
| harleys | 3/5/2009 |
Q: i bought a 1982 shovell wide glide and i am running into some probs. i dont think it is the right ...
A: Harley didnt use vin numbers on the frames before 1970, only the motor, so you probably have a pre ...
|
| Shifter Pawl Assembley | 3/5/2009 |
Q: I have a 2005 Ultra Classic. I bought the bike used. I shifter shaft was loose / stripped out. I ...
A: To remove the shifter shaft you have to pull the gears out of the trans. there is not enough room to ...
|
| How to check Harley for front end or frame damage | 3/5/2009 |
Q: I found an 04 deuce for sale by the insurance company. Bike starts and runs fine and would make an ...
A: It takes a pretty good hit to damage the triple trees as well as the wheel and axle. Just laying the ...
|
| how to replace clutch on a 1989 elctra glide? | 3/4/2009 |
Q: how to replace clutch on a 1989 elctra glide?
A: Drain the primary fluid. Remove the primary cover. Looking at the clutch you will see the clutch ...
|
| !977 FLH Shovelhead | 3/4/2009 |
Q: When I depress Starter button I hear my new relay "click" and i hear Unknown age Solenoid " click" ...
A: I would go ahead and replace the wires youa re refering to, since they look old and bad. If the ...
|
| Wiring | 3/3/2009 |
Q: I was always told that if you add electronic accessories to your motorcycle that you shouldn't go ...
A: If you add electronic items to your bike without going off a fuse then you are taking a chance, if ...
|
| ape hanger install | 3/3/2009 |
Q: im installing 12 inch ape hangers on my 07 883. the dimensions are 35" wide, 12" rise, 8" center ...
A: Your best bet is to remove the old handle bars and install the new ones. Leave the lines attached to ...
|
| throwout bearing | 3/2/2009 |
Q: how difficult is it to change a throwout bearing on a 1996 fxstc?Can you talk me through it?I try to ...
A: First, you drain the trans fluid. Then go to the clutch cable and put some slack in it. Go to the ...
|
| How to check Harley for front end or frame damage | 3/1/2009 |
Q: I found an 04 deuce for sale by the insurance company. Bike starts and runs fine and would make an ...
A: Look over the frame, checking for cracked paint or compressed metal. Check at the weld joints for ...
|
| Front Fork Leak | 2/28/2009 |
Q: I have a 1995 FLHTC and am not able to keep air pressure in the front fork system. I am not sure ...
A: there are only a few places for it to leak. One is the bolt going into the bottom end of the fork, ...
|
| 2007 street bob | 2/27/2009 |
Q: i was recently in an accident on my bike didn't do much damage just broke my clutch lever well i ...
A: It sounds like you have a short in the wiring. I would start by disconnecting the wire going to the ...
|
| Synthetic oil usage | 2/27/2009 |
Q: I have a 1991 FXSTC. It is a high mileage bike and I am wanting to know if it would be a good idea ...
A: i know that using synthetic will make the bike run cooler and is suppose to last longer. The problem ...
|
| Air cleaner | 2/27/2009 |
Q: I have a 09 street glide and want to change the stock air clear with either a stage I or a stage II. ...
A: Your bike came from the factory a little lean. Adding the air cleaner will lean it out a little ...
|
| Nightster clutch LOTS of friction. | 2/25/2009 |
Q: I have an 08 Nightster. I have gotten all the regular maintenance except the 5k and I am at 5k. I ...
A: You can adjust the clutch yourselfwithout a problem. Loosen the clutch cable so there is some play ...
|
| rocker cover bolts | 2/25/2009 |
Q: is it ok to re tighten the bolts on the rocker cover to my 02 FLHT,i noticed that the rear bolts are ...
A: There is really no problems with removing the tank. You just have to drain the gas, remove the seat ...
|
| 1995 harley soft tail | 2/24/2009 |
Q: i have a 1995 harley soft tail & the battery keeps going dead. i understand there could be a short. ...
A: First thing you need to do is check the battery to make sure it has water in it and its good. If it ...
|
| 201 Dyna | 2/22/2009 |
Q: I just bought a 2001 Dyna Super Glide with stock exhaust and carb. I installed a set of Vance & ...
A: Generally, adding a high flow exhaust will lean the bike out a little. Your best bet is to go for a ...
|
| 87 flhtc | 2/22/2009 |
Q: on my 87 flhtc,the bike will shut down when first ride of day,usually 3rd or 4th gear.The psi gauge ...
A: I am assuming that the gage you are refering to is the oil pressure. It sounds like you have a short ...
|
| leaking front cyl. head gasket on a 2003 fatboy | 2/20/2009 |
Q: need some good tips on how to change this gasket properly
A: Not sure what you marn by good tips. Its just the question of removing the tank and tearing down the ...
|
| Idle problems | 2/19/2009 |
Q: I have a 07 FXDC that most days has a idle with a mind of it's own. Most of the time after a brief ...
A: The problem with the new bikes is there are so many sensers that it is hard to tell which one it is, ...
|
| 1994 harley sportster question...... | 2/19/2009 |
Q: Ok, for starters i work at a local dealership in iowa(wash bay). i purchased a used 1994 sportster ...
A: I have to back up. the ball and spring are located in the oil filter housing. I was thinking of a ...
|
| 1987 flhs | 2/19/2009 |
Q: mike , have a problem at 70 miles an hour, bike will shut off, have had the carb., cleaned two ...
A: There are two different reasons for your problem. One is gas starved. Go for a ride with the air ...
|
| 1987 flhs | 2/18/2009 |
Q: mike , have a problem at 70 miles an hour, bike will shut off, have had the carb., cleaned two ...
A: What ignition are you running? When you say it shuts off, once you get below 70 does it immediality ...
|
| 89 fxsts rebuild | 2/18/2009 |
Q: last year i bought my 1st Harley a 1989 fxsts. It had a small leak in the rocker box that ...
A: Go to the front exhaust. Rotate the motor so the lifter is all the way at the bottom of its stroke. ...
|
| 1994 harley sportster question...... | 2/18/2009 |
Q: Ok, for starters i work at a local dealership in iowa(wash bay). i purchased a used 1994 sportster ...
A: Since you lost your oil tank out of the tank then that means the check valve in the oil pumping is ...
|
| carlini handle bars | 2/17/2009 |
Q: i just bought a set of 16'' carlini gangster apes for my 05 road king what length cables do i need ...
A: Here is how I go about putting on taller handlebars. First, I remove the cables and install the ...
|
| 1997 heritage springer softail | 2/17/2009 |
Q: When running it is hard to shift into neutral, someone said it could be a throw out bearing, what ...
A: On the shifter cam in the trans, there is a fine line where netural is. over time it gets harder to ...
|
| Loose rear Harley transmission shift lever | 2/16/2009 |
Q: Mike, got a 97FLHPI and read the previous post ('97) concerning the loose rear shifter lever. You ...
A: If you just loosen the screws you still cant move the inner primary until you remove the clutch ...
|
| 1985 ironhead 1000 | 2/15/2009 |
Q: where do icheck primary oil,and where do iadd oil?
A: The primary and trans share the same oil. You add oil from the center inspection plate on the ...
|
| stator check | 2/14/2009 |
Q: i need the procedure for testing stator for 05 softtail as i have burned up a 2nd regulator. ...
A: First, unplug the regulator. At the plug for the stator go from one pin to ground with a OHM meter, ...
|
| Keith Black pistons | 2/14/2009 |
Q: I am putting a 1200 kit in my 98 883 sportster, I stopped at my machinist and he said Keith Black ...
A: Keith Black pistons are good pistons and should hold up quit well as long as the cylinders are honed ...
|
| Slip-ons or hole in baffles | 2/13/2009 |
Q: I have a 2007 Sportster 1200 Custom and I want to change my stock pipes to obtain a louder sound. ...
A: First, pipes change colors due to heat. The leaner a bike runs the hotter it runs. When you open up ...
|
| 1998 FLSTC Starter Problem | 2/13/2009 |
Q: I have a 1998 FLSTC EVO. The starter spins but does not engage, the battery is fully charged. The ...
A: If the jackshaft pops out then the jackshaft might be bad. What you would have to do is pull the ...
|
| oil return | 2/13/2009 |
Q: i just bought a 1996 fxsts. when i start the bike , the oil level gets higher as it warms up and ...
A: In the oil pump there is a ball with a spring. When the bike is not running the ball is suppose to ...
|
| tranny | 2/13/2009 |
Q: have an 01 night train. i recently blow the transmission. well i have been looking around and i ...
A: On the trans. even though they look the same the mounting is different so you are going to have to ...
|
| spark plug | 2/12/2009 |
Q: front spark plug burns light dark.and the back one burns white on the strap grand.is that ok?thanks
A: If you are talking about a harley, the front cylinder stays a little cooler than the rear. If you ...
|
| oil return | 2/12/2009 |
Q: i just bought a 1996 fxsts. when i start the bike , the oil level gets higher as it warms up and ...
A: You have oil weeping into the bottom end of the bike through the oil pump. If you have to much oil ...
|
| 1998 FLSTC Starter Problem | 2/11/2009 |
Q: I have a 1998 FLSTC EVO. The starter spins but does not engage, the battery is fully charged. The ...
A: First thing you need to determine is if the jackshaft is moving when you hit the starter button. ...
|
| sportster speedo problem | 2/11/2009 |
Q: My uncle has a 97 or 98 1200 sportster. Recently the magneto went out on him. After he got his bike ...
A: Since your bike has a speedo that run off the front wheel then you have a problem with one of the ...
|
| shovelhead | 2/10/2009 |
Q: I need to know how to check the starter solenoid. I have power from the switch to the solenoid but ...
A: There are 3 posts on the solenoid. One large one is constant hot. The other one gets hot when you ...
|
| 1955 panhead | 2/10/2009 |
Q: i have a 55 fl recently rebuilt 90 miles ago,when built by a shop i had given them a su carb and a ...
A: If the pistons you told me were installed then you should be running around 90 to 100 PSI, so your ...
|
| 75 sportster oil line routing | 2/8/2009 |
Q: need help routing oil lines, theres no oil cooler on this bike. confused on which 3 oil lines go to ...
A: The oil line cannect to the back of the tank. The lowest port ont he tank is the feed to the oil ...
|
| ignition | 2/8/2009 |
Q: I am hooking up a tach to a single fire ignition. The modual is a Crane HI4 and the coil is unmarked ...
A: The single fire coil has three posts. Usually the one in the center is the positive one, but check ...
|
| carb cough | 2/7/2009 |
Q: i just bought this bike so ill tell you what i do know the bike is a 1999 FXD harley with a 95 ci ...
A: Your cough in the motor could be caused by a pushrod being to tight if you have adjustable pushrods ...
|
| voltage gauge pegs | 2/7/2009 |
Q: I have a 2004 electra glide classic, the voltage gauge was peging above 16, engine lite comes on, ...
A: First, unplug the regulator. Do a OHMs test from pin to pin on the stator and then pin to ground. ...
|
| '85 ELECTRA GLIDE F/FENDER REMOVAL | 2/6/2009 |
Q: I've written to you before and you were right on with you suggestions. And I still THANK YOU FOR IT. ...
A: To take the front fender off you will have to remove the front tire and caliber. Then just remove ...
|
| chain oiler rear drive chain | 2/5/2009 |
Q: I have a 1977 Super Glide and I am trying to find out how to rerun my chain oiler. I just found a ...
A: Your rear chain oiler runs from the t on the oil pump and drips on the chain from a hose fitting ...
|
| chirping ( alignment eliminated) | 2/4/2009 |
Q: My wifes '98 Springer Anniv. Loud chirp from drive belt on de-celleration as well as sometimes ...
A: Since your belt is aligned properly then its probably the belt itself. About the only thing you are ...
|
| chain oiler | 2/4/2009 |
Q: I have a 1977 Super Glide and I am trying to find out how to rerun my chain oiler. I just found a ...
A: The small hose goes from the oil pump to the back of the inner primary. The hose at the center of ...
|
| ignition switch | 2/3/2009 |
Q: how do u get the ingniton switch off,so i can get the plastic cover off under it ANSWER: What year ...
A: Put the key in and unlock. With the key still in turn the knob to access. There is a small release ...
|
| 1996 FXDWG Engine Vibrations | 2/2/2009 |
Q: I've done some reading here, and elsewhere, and I have a bad engine vibration problem on my mildly ...
A: With that many miles I would suppect that the rod bearings are worn and lose, which would cause the ...
|
| 1986 FXST VOES | 1/26/2009 |
Q: I have a 1986 softail with a mildly modified drivetrain. Modest cam, Crane HI-4 Single Fire ...
A: Since your bike has had the sputter since the rebuild I would suspect that it is not the VOS. I see ...
|
| Speedometer/ Police Special | 1/26/2009 |
Q: I have a '93 Police Special Road King and was wondering how to fix the speedometer? I haven't yet ...
A: Your speedo runs off the front wheel and has a speedo drive unit. Disconnect the cable from the ...
|
| 1993 FXDL | 1/25/2009 |
Q: I need some advice on rebuilding the carb on my stock FXDL. I do not know if it is the gas I use or ...
A: the next time it happens, pull the bowl off the carb and check the intermediate jet. the bowl has a ...
|
| Replacing the clutch lever | 1/24/2009 |
Q: How do I replace the clutch lever on my '07 sportster/nightster? it's how to handle the cable that ...
A: Loosen the adjuster on the cable so it has alot of slack in it. remove the pin that holds the lever ...
|
| changing a clutch handle on a 1200 sportster | 1/24/2009 |
Q: how do I change a clutch handle on a 1200 sportster. removed pin,and locking screw, how do I get the ...
A: Go to the adjuster on the cable and loosen it so you have slack in the cable. Remove the pin holding ...
|
| fouling out plugs | 1/24/2009 |
Q: I have a 1985 evo motor that has a s&s super E carb on it and straight pipes everything thing else ...
A: Since you changed your coil Iwould recommend changing the plug wires. They could be going bad, which ...
|
| engine sound like valves | 1/24/2009 |
Q: I have a FLHT 1994 Electra Glide police certified edition it's engine was was repaired about three ...
A: Your ticking is probably the lifters not getting enough oil. What you need to do is connect a ...
|
| Upper end rebuilding | 1/23/2009 |
Q: I have 99 softail 1340 with 28k miles.I have done every potential mod. to increase hp. excluding ...
A: When you rebuild the top end you remove the heads and rework the valves, remove the cylinders and ...
|
| 1990 heritage softail | 1/20/2009 |
Q: my heritage broke down lately when i was out for a ride,the bike just died out.I checked fuel and i ...
A: Its not the pickup, since you have a spark. The pickup is nothing more than a on off switch for the ...
|
| changing turn signals | 1/18/2009 |
Q: I changed the turn signals on my wifes' sportster, and I'm not sure which wires go to what. On the ...
A: If you are refering to the front turn signals the black is ground, blue is running light and the ...
|
| battery tender | 1/18/2009 |
Q: I have a 2008 883L and I was wondering if my bike comes with the pigtail to connect a battery ...
A: It doesnt come with one. You would need to install it. Just connect the wires to the battery and ...
|
| battery change on tour glide | 1/18/2009 |
Q: Dumb me left the ignition switch in the on position. My garage isn't heated and the battery is ...
A: The only problem you will have is if you left the on/off switch on with the ignition. If you did you ...
|
| 83 fxwg | 1/16/2009 |
Q: my 83 shovel has a clutch adjustment problem. iv replaced the discs and the bearings in the hub seem ...
A: Check your throw out bearing to make sure its ok. Also, check the plates to make sure they are not ...
|
| my fathers motorcycle | 1/15/2009 |
Q: unfortunately its not a harley its a 1973 Honda cb450 but my question is how do i start restoring my ...
A: First thing you need to get is a service manual for your bike so you know the specs and how to work ...
|
| head mods | 1/14/2009 |
Q: I am currently getting my 883 cylinders bored out for 1200. Do I need to do any machining to the ...
A: As long as the pistons are designed for conversion from 883 to 1200 you dont have to do anything to ...
|
| 68 harly | 1/13/2009 |
Q: How can i check valve timing on my shovelhead without opening the entire engine?
A: You need a timimg light and a clear timing hole plug. Pull the timing plug out of the left side of ...
|
| 1340 EVO | 1/12/2009 |
Q: Mike Ive recently returned from a tour in Iraq and purchased a 1990 Electra Glide Sport. It had one ...
A: running hot can be caused by two things. One is running the bike to lean and the other is the timing ...
|
| rocker box leak | 1/12/2009 |
Q: 1993 FLSTF. rear cylinder is leaking. it has been for awhile. how can i tell if the leak is between ...
A: Usually your leak is between the lower box and the head. Since you have to tear it apart, you need ...
|
| speedo/turn signal cancel | 1/12/2009 |
Q: have a '96 883, someone has installed a mech. drive speedo on and now the turn signals do not self ...
A: You are correct on the speed signal output wire from the speedo. As to the mini speedo having the ...
|
| 06 Harley Davidson 883R Front Brakes | 1/12/2009 |
Q: my question is in regards to my 2006 883r sporster. I've been experiencing front brake ...
A: You can have the rotors turned, but you would have to find somebody with a big enough lathe. You ...
|
| sputter | 1/12/2009 |
Q: I have a '96 Heritage with about 40K on it. I recently replaced the starter and at same time the ...
A: Nest time you change plugs, get a set of Champions. They are cheaper and do the same thing as the ...
|
| Rebuliding | 1/10/2009 |
Q: I would like to get into rebuilding old Harley. Where would be a good place to start? I am an ...
A: One of the things you need to get is a service manual for the year you are looking at. What ever ...
|
| chattering noise | 1/10/2009 |
Q: i have a 1982 fl roadking i purchased about a year ago.on a fairly long ride i noticed a chatter ...
A: The noise you are hearing might be coming from the head gasket. When they blow, they do make some ...
|
| brake light fuse | 1/10/2009 |
Q: I can't get to a manual, where is the fuse for a brake light on a 1988 FLSTC?
A: You dont have fuses on your bike, you have breakers. If only your brake light is not working then ...
|
| electric start problem | 1/9/2009 |
Q: I have a 2004 883 with 3500 miles.(bought this year used and has always been hard to start) I ...
A: You need to determine where you short is, so you will need a test light. First, check you ...
|
| ACETONE ON CHROME | 1/9/2009 |
Q: DO YOU KNOW WHAT EFFECT ACETONE HAS ON CHROME?
A: I dont think it will hurt it if you are using it to clean chrome. I use carb cleaner to clean chrome ...
|
| how to remove baffles | 1/9/2009 |
Q: I would like to ask you how can i remove the baffles from my '07 Scramming Eagle street performance ...
A: Look at the back of the pipe. If there is a bolt then remove the bolt and you can pull the baffle ...
|
| flathead 50's servi-car | 1/9/2009 |
Q: Motor came in a box trying to complete this project myself, came into a problems no one seems to ...
A: We might be talking about two different oil pumps, since they made several diffrent ones for the ...
|
| EVO vent to oil tank | 1/8/2009 |
Q: I have several EVO powerd bikes. Some case vent and some head venters. All seem to collect oil in ...
A: If you vented everything to the oil tank the oil tank would be pressurized and the dipstick would ...
|
| Locked Front Brake/Wheel | 1/8/2009 |
Q: I read your profile regarding only knowing about Harleys but I have a quick general question. I ...
A: Most brake calibers have whats called a puck inside. It is moved by the pressure when you apply the ...
|
| oil leak | 1/7/2009 |
Q: hey there well i am not sure if this question will fall under your knowledge feild.. but i just ...
A: your leak could be about anywhere. heres is the best way to find it. Clean the motor very well. ...
|
| neutral switch installation | 1/7/2009 |
Q: I have an 01 Fat Boy and need the procedure for installing the neutral switch.. Can you help me ? ...
A: Your right on the wires. I was thinking of another year. the chrome cover should just slide off. ...
|
| Swing Arm Bolt Removal | 1/7/2009 |
Q: I am trying to remove the swing arm bolt in my 1989 Harley FLHTC. I have tried heating, beating and ...
A: Once you have the weight off the swing arem it should just slide out when you remove the nuts. It ...
|
| Carb jetting??? | 1/7/2009 |
Q: I have a 113" s&s, v&h pipes w/baffles, forcewinder forward facing intake and a Super G carb.At ...
A: you have a problem with the carb. If you have to air/fuel mixture screw in all the way the bike ...
|
| O5 FLHTCUI oil consumption | 1/7/2009 |
Q: I bought an 05 FLHTCUI brand new with a 1550 ST Legal EFI 95" kit with Syn.3 installed by the ...
A: If you donthave a leak then you are burning oil. There are two places that you can get oil in the ...
|
| replacing forks | 1/6/2009 |
Q: mike i would like to install chrome lower forks on my 07 fatboy how do i go about it? thanks Mike ...
A: First, you need to jack up the bike so the forks are off the ground. remove the fender and brake ...
|
| flathead 50's servi-car | 1/6/2009 |
Q: Motor came in a box trying to complete this project myself, came into a problems no one seems to ...
A: On your oil tank you should have 3 fittings. the lowest one is the feed line, the next highest one ...
|
| Opinion Bearing Migration | 1/5/2009 |
Q: "Hi Mike, Sorry, in my first email I incorrectly stated that it was the "left bearing that ...
A: What you have to do is measure the inner race and the bearing, then hone the outer race to size it. ...
|
| no throttle response (continued) | 1/4/2009 |
Q: Mike, I am using a S&S "G" model carb. The lifters are hydraulic and the exhaust is aftermarket type ...
A: The jets you are using should make the bike run with maybe a little miss, but it should still run ...
|
| "Correction" Right Hand Main Bearing Migration | 1/4/2009 |
Q: "Hi Mike, Sorry, in my first email I incorrectly stated that it was the "left bearing that ...
A: To answer your first question, no it is not common. In fact, I have never seen this happen. The ...
|
| Harley Davidson Headlight low beam | 1/3/2009 |
Q: I have a 05 softail (fatboy) I have replaced the Bulb & switch & I still have no low beam I have ...
A: Your short would be between the switch and the light itself. Check the plugin for the headlight to ...
|
| no throttle response (continued) | 1/3/2009 |
Q: Mike, I am using a S&S "G" model carb. The lifters are hydraulic and the exhaust is aftermarket type ...
A: It sounds like your carb is jetted to big, which would cause the lack of power. Clean your plugs and ...
|
| oil coming out of air intake | 1/3/2009 |
Q: Was out riding for about half hour when all of the sudden oil startyed coming out of air intake. I ...
A: You have a couple of butterfly valves in the rockers to vent air out of the motor durning the ...
|
| followup on no throttle response | 1/3/2009 |
Q: Mike. This is a follow up on previous questions concerning no throttle response. I built a custom ...
A: Your compression is fine. Couple of questions. What carb are you running, are you using solid ...
|
| 2006 SPORTY 883 | 1/2/2009 |
Q: MIKE, I HAVE A 2006 883 SPORTY WITH 600 MILES I JUST CHANGED OIL TO LUCAS 20/50 SYN. WAS THIS A GOOD ...
A: Lucas is a good oil, so if you want to run syn. you picked well. Try running the 91 octane and see ...
|
| 2001 HD 1200c Sportster | 1/2/2009 |
Q: When ever I run over 65mph tbe bike spits oil out of the crankcase vent hose. Does not happen at ...
A: Your umbrella valves, located in the rocker boxes, are probably bad and need replaced. They are ...
|
| Sportster Forks | 1/1/2009 |
Q: I have a 1987 Sporty 1100 which was in an accident. The fork tubes are bent. These are the small ...
A: Pretty much any forks from 82-99 will fit your sportster as long as you change the triple trees. ...
|
| removal of the rear fender and gas tank | 1/1/2009 |
Q: i have a 1998 sportster 883. i am getting the tins painted by a friend in ohio but i need to remove ...
A: To get the fender off you have to remove the wheel so you can get the strut bolts out. You would ...
|
| 73 Sportster Iron Head Rebuild Project | 1/1/2009 |
Q: I have a 73 XLH Sportster rigid frame that I purchased in 1980 in a basket. I would like to build ...
A: Your cases were probably damaged from the trans locking up, not a motor problem. Many iron heads ...
|
| Charging two batteries | 12/31/2008 |
Q: Is it possible to charge two batteries installed in a 2002 Road Glide at the same time or in ...
A: Your problem sounds more time related than amp related. I would start by adding a battery, but use ...
|
| extra fuel tank for trike | 12/31/2008 |
Q: My converted H_D Road Glide to trike has resulted in using much more fuel than my wifes '97 FLHTCUI ...
A: You can add a float to the main tank to pump the fuel and shut the pump off when it full, but the ...
|
| 2004 Fatboy FLSTF lower fork replacement | 12/31/2008 |
Q: I just bought chrome lower forks for my 2004 FLSTF. I'm looking for instructions on how to do the ...
A: Your best sourse would be the harley service manual. Its not that hard to change them out. Lift the ...
|
| 05 Dyna | 12/31/2008 |
Q: I had previously changed the muffs to Screaming eagle slash, Air filter change and a map change ...
A: Your best indicator of a lean condition is checking the spark plugs. Pull them and they should be a ...
|
| extra fuel tank for trike | 12/30/2008 |
Q: My converted H_D Road Glide to trike has resulted in using much more fuel than my wifes '97 FLHTCUI ...
A: It is going to be alot of work to add a tank. First, you would have to deside where you are going to ...
|
| Charging two batteries | 12/30/2008 |
Q: Is it possible to charge two batteries installed in a 2002 Road Glide at the same time or in ...
A: You can run the batteries in series and charge both at the same time off the charging system on the ...
|
| '01 road king w/ apehangers | 12/29/2008 |
Q: i have 18" apes on my '01 road king. i love 'em however the handling is lacking (esp. wind,rain ...
A: the problem you are having is the higher you go with the handle bars the more flex you get. You can ...
|
| followup on no throttle response | 12/28/2008 |
Q: Mike. This is a follow up on previous questions concerning no throttle response. I built a custom ...
A: the plugs would indicate that you are running rich, which would cause the falling flat.Even siting ...
|
| Generator light on | 12/28/2008 |
Q: I have a 1984 harley sportster. The generator light started to flicker, when off and then came on ...
A: To polorize the generator you attach a jumper wire to the A post of the generator and momentarily ...
|
| front end bearings | 12/28/2008 |
Q: I bought a perse performance triple tree set. At like 70 mph I get a side to side sway does the ...
A: the bottom bearing should be pressed on all the way tight to the dust cover. Check your play in the ...
|
| Changing Shocks | 12/28/2008 |
Q: I have a 06 XL883C, I want to lower my bike, plus feel like I ride in it not on it. If that makes ...
A: The Progressive shocks will give you a better ride than the stock ones. As to lowering, if you lower ...
|
| Generator light on | 12/27/2008 |
Q: I have a 1984 harley sportster. The generator light started to flicker, when off and then came on ...
A: What you need to do is test the generator and regulator. the problem is you are not going to have to ...
|
| 03 FLSTCI Runs Rich | 12/22/2008 |
Q: I own a 03 FLSTCI (fuel injected) that is blowing gas out the exhaust. The motor is stock with a Big ...
A: No problem. The power commander can have gone out as I said in my previous answer and you still have ...
|
| 03 FLSTCI Runs Rich | 12/21/2008 |
Q: I own a 03 FLSTCI (fuel injected) that is blowing gas out the exhaust. The motor is stock with a Big ...
A: It sounds like your Dyna modual is not working correctly, so you either have to find somebody that ...
|
| Charging problem . . . | 12/20/2008 |
Q: I have a problem with the charging system on my '02 Wide Glide. On one of my last rides in the fall ...
A: First you need to start the bike and make sure you have a charging problem. Ater the bike is ...
|
| spring from rear brake caliper | 12/20/2008 |
Q: I have a heritage softail 96 model.My problem is with the single piston rear brake caliper.It was ...
A: This is going to be tough to explain on here without a pic, but it goes ont he back of the caliber ...
|
| 91 Fatboy burning oil. | 12/19/2008 |
Q: I recently bought a 91 Fatboy.(1st Harley, don't know much about them yet) The previous owner had a ...
A: There are two places you get oil to burn. One is from the valve guides and the other is around the ...
|
| General Checklist | 12/17/2008 |
Q: Hey Mike, What's a good check list to follow when looking at purchasing a vintage bike that hasn't ...
A: One of the worst things for a bike is to sit for a long period of time. About he only thing you can ...
|
| solenoid | 12/16/2008 |
Q: How do you check a solenoid on a 2003 fatboy and see if it is good or not? ANSWER: What happens ...
A: First, make sure you have a good battery and good ground. Go to the starter and locate the small ...
|
| ss eng | 12/14/2008 |
Q: s&s on a 2002 indian spirit. has set for a couple mos. tried to start after several attempts noticed ...
A: That is the vent for the bottom end of the motor. What happens is the oil tank probably weeped some ...
|
| 2001 heritage softail classic | 12/13/2008 |
Q: When I have been riding and stop for gas I have to let my bike cool down before starting it again ...
A: Your grinding noise might be coming from the starter motor. When your riding the bike, the starter ...
|
| removing rear fender | 12/13/2008 |
Q: please tell me the steps in removing the rear fender on a 1997 sportster 1200. thank you.
A: First, jack the bike up. Remove the axle and shide the wheel foward and remove the belt. Then remove ...
|
| pulley cover sportster | 12/12/2008 |
Q: I want to install a chrome pulley cover on my sportster how do I do this your help will be ...
A: If you are refering to the rear pulley you would have to jack the bike up, remove the axle, push the ...
|
| Harley jackshaft starter problem | 12/11/2008 |
Q: I have a shovel inner/outer primary setup, and have a problem when going to fire the bike up. ...
A: Check the bearing in the primary where the jackshaft goes to make sure it good. I would also check ...
|
| starter solenoid | 12/11/2008 |
Q: How do you check the starter solenoid on a 2003 fatboy to see if it is good. Just clicks when I hit ...
A: First you need to check to see if you have power going to the starter from the starer relay. Locate ...
|
| 2009 Road King SE packages | 12/10/2008 |
Q: I'm thinking about buying a 2009 Road King and would I like the idea of getting the SE stage I ...
A: Anytime you go for more horses you will give up some gas milage. With the current motor on the 2009 ...
|
| 2002 Harley Davidson clutch engagement | 12/10/2008 |
Q: I've recently acquired a 2002 Patriot motorcycle with Harley new EVO motor and trans. The clutch ...
A: Loosen the adjuster on the cable so you have some slack in it. Go to the adjuster on the clutch and ...
|
| 1996 stock 1200 xl carb. | 12/9/2008 |
Q: My wife's bike spits back through the carb. chokes out at the light and will die while she is riding ...
A: I would first check to see if you have a intake leak. Next, check for a exhaust leak. If they are ...
|
| 1970 shovel | 12/8/2008 |
Q: Ive got a 70 shovel of a friend of mine and its puking out about a quart of oil out the vent tube ...
A: the pressure is created when the piston moves down. What is happening is the oil pump has a check ...
|
| Quiet exhaust for a '77 Superglide FXE | 12/8/2008 |
Q: Firstly, thanks for all the great answers to the posts. I fixed an electrical problem by reading ...
A: The problem with turn outs is getting a baffle in. They dont really go around corners and I dont ...
|
| 1987 flhs | 12/8/2008 |
Q: I have been working on this bike for several weeks. It started when the starter solenoid took a ...
A: If your voltage is dropping that low, the you have a grounded wire somewhere and its killing the ...
|
| Starter drag | 12/8/2008 |
Q: I have a '98 Wide Glide. The starter started dragging every once in a while until now it just ...
A: Once you have checked the cables and made sure thy are not the problem then you would have to pull ...
|
| 2005 Dyna Super Glide | 12/7/2008 |
Q: First winter with my bike where is the battery and do I remove it in the cold months?
A: Your battery is located on the right side of the bike. Your best bet on the battery is to install a ...
|
| Rotor and stator Help | 12/6/2008 |
Q: I have a 2000 RK Classic. Battery went completely dead during a ride. Battery charged up OK after ...
A: If you are showing that low of voltage at the sttor then the stator is bad and needs replaced. You ...
|
| pushrod adjustment 2001 fatboy | 12/5/2008 |
Q: looking for proper adjustment procedure.i know the basics for valve adjustment as ihave done al ...
A: i was just checking. Remove the spark plugs and rotate the motor so the front exhaust is at the ...
|
| tach hookup | 12/5/2008 |
Q: could you please tell me how to wire tach on my 03 heritage classic. have a BARON tach with adapter ...
A: The yellow wire from the adapter goes to the negitive side of the front coil. The blue wire from the ...
|
| sportster 1st gear slips | 12/4/2008 |
Q: i have the same problem as these folks who better sum it up. both me & my wife have sportsters ...
A: If it skipped a tooth is would do it all the time and skip thoughout the RPM range while you are in ...
|
| wiring harness fitment | 12/4/2008 |
Q: I have a92 flh ultra classic,has a burnt harness.I have found various differences between ...
A: If you cant find a harness for your 92 then you are going to have to go the route of using a ...
|
| shovelhead pushrod length | 12/3/2008 |
Q: I am helping a friend put his 1972 flh back together after installing an andrews stock replacment ...
A: First, when installing the pushrods you should bleed the tappets to make sure they are not pumped up ...
|
| 1983 flhtc shovel 5speed | 12/3/2008 |
Q: 010 over and right after i got it the rear head gasket blew the top end,oil pump,stator and clutches ...
A: On the oil leak, just replace the rubber gaskets and that should solve the problem. On your pipes, ...
|
| Bolt On Chopper Kits | 12/1/2008 |
Q: I have seen web sites such as "Seeger Cycle, Chopper Kit" about a bolt on chopper set up. They give ...
A: i have never used these kits, but I did look at them on the web. What you are doing is adding rake ...
|
| Front shock leaking oil FLHR-1 2003 Road Ki | 11/30/2008 |
Q: 2003 HD Road King, FLHR-1-(No front air shocks) 7000 miles, bought 3 months ago with 4600 miles, ...
A: You need to jack up the bike so there is no pressure on the forks. remove the top cap. If that is ...
|
| 1999 ultra classic twin cam 88 | 11/30/2008 |
Q: tach stopped working red engine light on and off just happened completely stock bike 30.000 miles ...
A: Since you have a check engine light you need to know the codes to know what to repair. Hold the ...
|
| Changing triple trees | 11/30/2008 |
Q: I have a 2006 nightrain with the stock 3 degree tripple tree. I want to change them to a 5 or ...
A: Adding the 7 degree will be fine and give the bike a streched look. If you dont lengthen the forks ...
|
| FLHRC Front Caliper Installation | 11/30/2008 |
Q: I have a 2006 FLHRCI. I just replaced the front fender. I had a hard time getting the calipers off ...
A: Its best to have the front wheel off the axle and the bike jacked up a little. Install the fender ...
|
| my 1981 superglide tach.needle flutter | 11/29/2008 |
Q: BEFORE I replaced any parts, I asked about why my tachometer needle is bouncing around quite a ...
A: in your previous question you didnt mention the power loss, so I assumed it was a bad tach. When you ...
|
| EFI tuning | 11/28/2008 |
Q: I recently put Rush slip ons and an Arlen Ness Stage II air filter on an '08 FLHTC. I am attmepting ...
A: the popping is from not enough back pressure which will cause a build up of gas in the exhaust. ...
|
| Harley Won't Start | 11/28/2008 |
Q: You helped me out recently with some problems and now I have another one. My 1998 883 XLH Sportster ...
A: First thing you need to do is determine if you have power going to the starter. there is a small 12 ...
|
| Triple Trees | 11/28/2008 |
Q: I have a 2001 FXST. I would like to put 4 degree triple trees on the bike. Concerned about trail ...
A: The one thing you have to remember about adding degrees to the front end, it will handle better in a ...
|
| 96 XL 1200C | 11/28/2008 |
Q: What is the widest rear tire that I can put on my 96 1200C with out having to install a wide tire ...
A: On the front tire you can use the 90/90H-21. On the rear, you can go to a 140 tire, but its going to ...
|
| 2007 FLHTC | 11/27/2008 |
Q: I have had a shimmy in my front end since I have bought it in 2007.The harley shop replaced front ...
A: A shimmy in the front end can be caused from a couple different problems. Bad front tire, bent rim ...
|
| 2008 FXD idle | 11/26/2008 |
Q: Can anything be done to calm the high idle characteristics of the 08 Superglide. It has been that ...
A: Since you havent made any changes then you dont need to remapp. you can adjust the idle, it will not ...
|
| Gas smell | 11/25/2008 |
Q: I have a 2000 FXST which I bought with 5k miles on it. It now has 35k and over the past few months, ...
A: your correct, the vent line should not be plugged. I dont know much about the valve since I am in ...
|
| 1986 FXSTC oil tank outlets | 11/24/2008 |
Q: I'm working on a 1986 FXSTC and neeed to know which oil line goes to which nipple on the oil tank. ...
A: The bigger one is the drain that is going to the solid rod. Look inside the tank to see where the ...
|
| S&S Shorty Sputter | 11/24/2008 |
Q: I know mention Harley but I was hoping you could help with my S&S 113ci motor with S&S Super G carb ...
A: Since you have spark and you ran the bike without the gas caps and its not a vent problem, then the ...
|
| starter problem | 11/23/2008 |
Q: I own a 1989 sportster 1200 that won't start. All I hear when I press the starter button is a loud ...
A: It sounds like you need to pull the starter and test it. there are several tests that need to be ...
|
| timing | 11/21/2008 |
Q: I've got a 91 FLHS that's started pinging when pulling under load, like going up a hill. It also ...
A: To stop the pinging you can retard the timing a little, which should help. Since you stated that you ...
|
| starter | 11/21/2008 |
Q: Hey Mike... Jim here and have pulled the starter out of my bike. The problem I have now is how do I ...
A: The bearings should just press in. You might have to use a socket the same size as the inside of the ...
|
| Gas smell | 11/21/2008 |
Q: I have a 2000 FXST which I bought with 5k miles on it. It now has 35k and over the past few months, ...
A: I dont know much about that valve since I am in Ohio and we dont have to have that valve, like ...
|
| s&s oil pump removel | 11/18/2008 |
Q: I own a 49 panhead with a s&s oil pump and on my last start up i noticed i have no oil pressure at ...
A: First you have to remove the outer cover. On hte shaft that goes through the pump and into the case ...
|
| remove fairing from flhtcu | 11/18/2008 |
Q: red about your issue turning an electra into a roadking. I'm in the same situation. MIne is a -96 ...
A: When you get a wiring harness it wil be the main harness running from the front of the bike to the ...
|
| 5 degree tree | 11/18/2008 |
Q: i am putting on a 5 degree tree, is 2" over long enough to maintaine same ride hight.
A: What you need to do is install the tree and then with the bike lever at the frame, take a ...
|
| FLHPI | 11/18/2008 |
Q: Trying to convert the front running lights from flashing to staying on when the headlight is on. Is ...
A: The problem you will run into is the power for the lights come from the TSSM which makes them flash. ...
|
| Oil Light problem; | 11/17/2008 |
Q: I have a 1999 Ultra Classic fuel enjected while traveling the oil light comes on, goes out, comes ...
A: there is one sending unit for your bike. it is on the right side of the motor. Should be a single ...
|
| Oil Light problem; | 11/17/2008 |
Q: I have a 1999 Ultra Classic fuel enjected while traveling the oil light comes on, goes out, comes ...
A: If you have good oil pressure, and I would check with a manual pressure gage, then you probably have ...
|
| 2000 dyna 88ci engine | 11/17/2008 |
Q: DO THE TWIN CAM MOTORS HAVE A HISTORY OF OIL PRESSURE FAILURE? MINE HAS FAILED TWICE IN LESS THAN ...
A: I havent heard of this problem with the twin cam unless there is a alingment problem on the oil pump ...
|
| Adjustable pushrods | 11/17/2008 |
Q: What is the best way to adjust the pushrods on a TC88 HD ? I rolled the motor over to get each cam ...
A: Go to the front exhaust and rotate the motor so the lifter is all the way to the bottom of its ...
|
| 85 HD rear brake pad replacement | 11/16/2008 |
Q: How do I replace the rear brake pads on my 1985 HD FLT?Is it much of a job? ...
A: Its pretty easy. remov ethe caliber from the bracket. While the old pads are in there pry open the ...
|
| HARLEY FUEL | 11/16/2008 |
Q: WHAT DO YOU THINK ARE THE PROS AND CONS OF THE HARLEY CARBURATORS COMPARED TO FUEL INJECTION? ...
A: the fuel injection is more efficent than the carb and creates a little more power through the power ...
|
| installing a clutch cable | 11/14/2008 |
Q: I am a woman and I have been riding for 4 years now. I have a heritage softtail classic. The ...
A: Its not that tough at all. You will have to remove the exhaust if the pipes cover the trans cover. ...
|
| Removing Baffles | 11/13/2008 |
Q: I have a 2008 XL1200L Anniversary Edition Sportster. I like the bike very much but it just isn't ...
A: Check your mufflers. If you see a small bolt going into the side of the muffler then you can remove ...
|
| modle | 11/11/2008 |
Q: i just got my first bike.it,S a 1998 sportster 1200 and thats all i know ..how do i find out what ...
A: You can give a dealer the vin number and they should be able to tell you what model it is. The only ...
|
| 1987 FXR oil leak | 11/10/2008 |
Q: Mike: thanks for the opprotunity to write. i have an '87 FXR with 16k miles on it (been in a shed ...
A: Probably the hardest thing on a bike is sitting that long. the gaskets get old and dry out and dont ...
|
| Signal Lights 93 Softail | 11/10/2008 |
Q: Mike, I just purchased a 93 spring softail with about 13,000 miles. The factory rear signal lights ...
A: In order for the turn signal modual to work there has to be so much currect drawn. The factory ...
|
| Harley Signal Canceler Module (TSM) | 11/8/2008 |
Q: . a few months ago i ran across this site and your replies while i was having trouble with the turn ...
A: Its notthe fact that you have low voltage at the turn signal modual, its that the light bulbs are ...
|
| 85 ironhead | 11/8/2008 |
Q: I've owned this bike for awhile now and its been decent, but it started leaking oil out of the ...
A: the gasket leaks probably from old age. in order the replace the gasket you have to remove the head ...
|
| S&S 113 | 11/4/2008 |
Q: I have an S&S 113" with 10,000 miles. I am running a brand new dynatek programmable ignition, ...
A: On your jetting, you can keep going smaller until you stop fouling plugs or the bike does not ...
|
| Starting the motorcycle | 11/4/2008 |
Q: I own a 2001 Harley Davidson Sportster 1200 Custom. Unfortunately, due to my job and I am not able ...
A: The bad thing about starting the bike and letting it idle is the motor does nto get hot enough. When ...
|
| clutch adjustment (Heritage Softail Springer) | 11/4/2008 |
Q: I have a 2000 flsts, I need to adjust my clutch. I have my cover off and am looking at an 11/16 nut ...
A: First, go to the cable and loosen it, so you have play in the clutch lever. Now, loosen the locknut. ...
|
| voltage gage going wacky | 11/4/2008 |
Q: Mr.Wells, I have a 2004 Electra Glide Ultra Classic.On a recent ride,I observed the voltage gage ...
A: Connect a volt meter to the battery and go for a ride and see if the volt meter does the same thing. ...
|
| 1994 HERITAGE SOFTAIL NOT CHARGING | 11/3/2008 |
Q: BIKE QUIT AND BATTERY WAS DEAD, REPLACED BATTERY AND IT RUNS BUT IS NOT CHARGING, CHECKED AT BATTERY ...
A: You first need to test the stator. Unplug the regulator and do a OHMs test from each wire on the ...
|
| clutch adjustment | 11/3/2008 |
Q: How do I adjust the clutch on my 2001 harley 883 sportster. Thanks Steve
A: If you have to much play in the clutch lever go to the adjuster in the clutch cable. If will be ...
|
| Oil Drain Plug / synth. oil | 11/3/2008 |
Q: There are two drain plugs, very close together, on the left side of the oil pan. One is slightly ...
A: There are certain oils that can be used in all three. What you need to do it check with the sales ...
|
| Engine | 11/2/2008 |
Q: I noticed my bike (1994 FLSTN)was leaking oil between the jugs and the case. I tore the engine down ...
A: Any time you pull the jugs you should hone and re-ring. Since your bike is a 94 you need to mic the ...
|
| S&S 113". Plugs fuel fouling & Gas in oil. | 11/2/2008 |
Q: I have an S&S 113" with 10,000 miles. I am running a brand new dynatek programmable ignition, ...
A: First, you need to test your coil and plug wires to make sure they are good. Where you say you are ...
|
| xl 1200s fork extension | 11/1/2008 |
Q: I saw your answer about putting longer fork tubes on a Sportster Sport with the addition of spacers ...
A: It will work on your bike. When you extend the fork tubes you need somthing in there to take up the ...
|
| 1993 FLHTC FAIRING REMOVAL | 10/29/2008 |
Q: I HAVE A 1993 FLHTC - I NEED TO REPLACE/ REPAIR THE SPEAKERS AND WAS WONDERING WHAT WAS THE BEST ...
A: You have to remove the front fairing to get to them. Remove the top bolts and the windshield will ...
|
| Front master cylinder Harley 94 FLSTN | 10/29/2008 |
Q: Mike I purchased a 1994 FLSTN that already had an aftermarket chrome front master on it. I have ...
A: Its not suppose to be that snug. It is suppose to move hte rubber plunger. You should get a new cup ...
|
| 1993 flhtc electric | 10/29/2008 |
Q: when i replaced the ignition switch myself, the plastic top threaded head broke, but i glued it ...
A: About the only things that can make your switch go bad is to much voltage, the switch that was put ...
|
| HD 2001 Soft tail, Starting Problem | 10/29/2008 |
Q: Rode the bike 3 days ago.....tried to start it today but got a popping noise. The engine did not ...
A: Check at the starter where the solenoid connects and see if you have power there when you hit the ...
|
| custom oil lines | 10/28/2008 |
Q: Hey Mike , I bough a stainless oil line kit for my 82 FXR , the problem is the chrome fittings ...
A: If they were to tight, then they would have to be honed. If they got honed to much it could cause ...
|
| custom oil lines | 10/27/2008 |
Q: Hey Mike , I bough a stainless oil line kit for my 82 FXR , the problem is the chrome fittings ...
A: I have a few questions. First, the wrist pin is a standard size for the S&S rods, so what did he ...
|
| i need more help. thank you | 10/26/2008 |
Q: my 2002 883 sportster hugger. Its been working fine, but now it wont start or even the lights come ...
A: It sounds like you might have a bad battery. I would have it tested. If you are sure that the ...
|
| true duals | 10/26/2008 |
Q: I have an 08 flhr & have been told several different things about air & pipes , I'am going to true ...
A: Your bike came from the factory a little lean to pass the EPA standards. When you change exhaust, ...
|
| oil dumping from crankcase breather | 10/26/2008 |
Q: Been clocking up the 1000 mile run in and the bike pukes oil from the crankcase regularly. Have ...
A: For the over heating, check to make sure you are not running to lean and also that your timing is ...
|
| Brakes | 10/26/2008 |
Q: I have an '83 FXR. I just put on ape hangers and when i was bleeding the front brakes but they ...
A: Keep bleeding them. the hole in the master cylinder it really small for the brake fluid to go ...
|
| Cycle Shack baffles to replace those in SSII on an FXSTC 2009 | 10/24/2008 |
Q: I have a 2009 FXSTC Softail custom. I changed the stock pipes for Screamin' Eagle II. The sound is ...
A: When riders are looking for a certain sound they are all different. What one person like another ...
|
| 02' Sportster electrical problem | 10/23/2008 |
Q: I have been re-building my 02' Sportster after being involved in a wreck. I had the wires to the ...
A: The fuses are located either under the seat or under the side panel. If the headlight doen not work ...
|
| electrical 86 flhtc | 10/23/2008 |
Q: things that stoped working at the same time-brake lights-nuetral light-spot ...
A: You have breakers in your bike and no fuses. I would test on both sides of the breakers to make sure ...
|
| 1977 Superglide | 10/22/2008 |
Q: I have an 77superglide 74inch. Motor went bad and I took the motor out to get rebuilt. While motor ...
A: the super carb is just fine for your bike and a lot better than the old stock carb. Since your bike ...
|
| 76 shovelhead | 10/22/2008 |
Q: Hey Mike, I have a 76'Shovelhead, the otherday it starting lossing power, seems to be leaking oil ...
A: You first need to determine why its loosing power. Pull your plugs and check them for fouling. If ...
|
| electrical-86-flhtc | 10/22/2008 |
Q: Hello-I have a 86 flhtc-noticed the other day that some times the blinkers would flash a little and ...
A: First, you need to check at the key switch to make sure you have power going to the breakers. If you ...
|
| Delkron transmission case 620-299 FXR | 10/21/2008 |
Q: I bought a roller project with this delkron trans case installed. Case is totally bare. What Harley ...
A: You cn fit any of the 5 speed gearsets in there. the only thing you have to be careful of is the ...
|
| Carb popping | 10/21/2008 |
Q: 06 883l. Carb always popped a little after I punched holes in the plug in my stock exhaust. Well I ...
A: Drilling the slide makes the slide react faster, but you have to go a certain size. Going to big ...
|
| Fork length on a raked front end | 10/20/2008 |
Q: I have a 98 Fatboy which had been lowered when I purchased it. The fork length now is 29" from axle ...
A: What you need to do is install the 5 degree rake in the trees. jack the bike up so the frame is ...
|
| starting my harley after storage | 10/19/2008 |
Q: Mike, I bought my first HD in July during my leave from Iraq, The bike has 500 mi. now . I didnt ...
A: Probably goiing to have to replace the battery and drain the old fuel. the other thing you will need ...
|
| blinkers and brake lights | 10/19/2008 |
Q: The blinkers on my 1991 softail heritage work only on accessory mode. My brakelights do not work on ...
A: Your bike does not have fueses, it has breakers. Check at the brake switch to see if you have power ...
|
| 1980 HD lowrider | 10/19/2008 |
Q: Mike, just got the HD...runs, looks OK but would like to take it apart and semi-customize it? What ...
A: Excellent 11,300 very good 8,000 good 6,000 fair 4,300 poor ...
|
| 1997 HD Sportster Carburetor | 10/15/2008 |
Q: I have two hoses that have rotted. The first runs from the rear of the fuel cut-off to a splitter ...
A: If the vaccumn doesnt open the petcock then the fuel flow will stop, so that might be the problem. ...
|
| 1997 HD Sportster Carburetor | 10/15/2008 |
Q: I have two hoses that have rotted. The first runs from the rear of the fuel cut-off to a splitter ...
A: The hose at the splitter is from the vaccumn on the carb. If it leaks the bike wont run. It has to ...
|
| fork brace | 10/14/2008 |
Q: HEY MIKE HOWS IT GOIN?.....IM THINKIN ABOUT PUTTING A SCREAMIN EAGLE FORK BRACE ON MY XLCH.....WHAT ...
A: The fork brace stiffens the forks and keeps them from twisting under a load. You install then about ...
|
| 79 XLCH sportster | 10/14/2008 |
Q: put in new clutch in my 79 sportster,do i tighten nuts all the way down on the release disc so the ...
A: Yes, you tighten the nuts all the way down on the spacers. Then loosen the cable so you have alot of ...
|
| 2000 Deuce Brake light | 10/13/2008 |
Q: My front brake lever is not activating my brake lights, although brake lights come on with the rear. ...
A: If you take the brake lever out and turn the ignition switch on, does the brake light come on? If ...
|
| motorcycle storage | 10/13/2008 |
Q: Mike on a 97 sporty 883 winter storage should i drain the oil tank i was told that the oil would ...
A: If the oil hasnt weeped int he past, then it probably wont. Start the bike and let it warm up and ...
|
| mileage | 10/13/2008 |
Q: Mike can you tell me what kind of mileage could i expect from a 1997 sporty 883 with a good ...
A: On the rebuild, its had to say how soont he motor will have to be rebuilt. It is going to depend on ...
|
| 1989 1200 sportster | 10/13/2008 |
Q: i have 1989 1200 sportster,it's been lowered.when i ride with my girl friend i here the chain ...
A: You need to check your chain to make sure its not to loose. If you want to convert it to belt drive ...
|
| brake lights stuck on | 10/13/2008 |
Q: i have a 1988 flhtc with about 16,000 miles on it.the brake light is stuck on . both wires to brake ...
A: Check at the front brake handle. You will notice that the cover for the throttle and the cover for ...
|
| 99 Dyna Super Glide | 10/12/2008 |
Q: Random engine missing.New plugs gapped at 040,new battery,good high octane fuel,clean air filter. ...
A: Check for a intake leak with carb cleaner. Warm the bike up and spray a little carb cleaner around ...
|
| 81 Sportster Rear Wheel | 10/12/2008 |
Q: 1981 Sportster Cast Rear wheel I replaced the bearing & races. If i try to tighten the axle the ...
A: what you need to do is remove the wheel and install the alxe with some spacers so you can tighten it ...
|
| enrichner problem | 10/12/2008 |
Q: I have a 2000 duece, garage kept so I never use the enrichner. I just tied to use it & its too hard ...
A: First, check the adjustment on it. behind the knob there is a plastic nut. Loosen it, pull it out ...
|
| Oil thru breather | 10/11/2008 |
Q: I have a 2001 Indian Scout (I know it's not a Harley, but it does have a 88ci or 1442cc S&S V-twin ...
A: Your oil is backing up in to the bottom of the motor. Your check valve in the oil pump is leaking ...
|
| how a motorcycle starter works | 10/11/2008 |
Q: I have a starter that worked just fine. Now when I hit the switch, the starter turns the jack shaft ...
A: When you hit the starter button the starter turns as well as the starter soleniod, which is othing ...
|
| crankcase breathe oil spillout | 10/11/2008 |
Q: i am confused about the location of my crankcase breather on my 1976 flh. it looks to me like ...
A: Your oil returns from the primary through a hose which is attached to a t from the vent on the ...
|
| 74 Ironhead clutch | 10/11/2008 |
Q: This clutch is driving me crazy !! I brought this bike back from a basket case and the motor runs ...
A: Thy this and see if it will disengage. Loosen the adjuster for the cable all the way, so your making ...
|
| 2003 HARLEY-DAVIDSON SPORTSTER | 10/11/2008 |
Q: HOW TO CHANGE SHIFTER FORK?
A: In order the change the shifter fork you have to remove the trans and tear it apart. I am going to ...
|
| "Bad Gas" | 10/11/2008 |
Q: The man I bought my used cycle from suggested that "every so often" he would "run a tank of medium ...
A: All the higher octane gas does is stop pinging or pre detonation, so if you dont have that problem ...
|
| 73 Shovel kick start to electric start conversion | 10/10/2008 |
Q: I have '73 shovelhead converted to 93CI (S&S) with alternator/regulator (no points to mess with) and ...
A: Your best bet is to get a conversion kit. It will have the parts you need, except for the battery ...
|
| Risers for Fatboy 2003 | 10/10/2008 |
Q: I'm a novice at working on my 2003 Fatboy...just purchased it. I'm having trouble removing the ...
A: First you have to remove the headlight assembly. Once you have that done you remove the passing lamp ...
|
| Harley Lights | 10/9/2008 |
Q: I have a 1998 ultra classic and when I start the bike the headlight high beam indicator stays on ...
A: On your front lights. You have a short in the lighting system. When you go to high beam the ...
|
| 91 fatboy charging system | 10/8/2008 |
Q: I have a 1991 fatboy the battery just went dead on.I charged the battery and did a test on it and it ...
A: First, at the battery, start the bike and see what the voltage is whne running at around 2000 RPM. ...
|
| 98 Softail | 10/8/2008 |
Q: I'm looking at a 98 Softail with 48K mi. It runs very good and hasn't had problems. Should I assume ...
A: I cant give you a price on repair, due to the fact that prices are different all over the country ...
|
| Removing Speedo on 93 Heritage | 10/8/2008 |
Q: Can you provide some instructions on how to remove the speedo? The lighting has failed and the ...
A: Remove the cowling over the speedo. There is a nut on top of it. If the odometer reset is in the way ...
|
| 97 sportster 883 | 10/8/2008 |
Q: I came down a hill at night low on fuel. Before I could switch to reserve, engine stalled. What was ...
A: Running ouot of fuel shouldnt have anything to do with the lights going off. They should have stayed ...
|
| 81 ironhead oilpump | 10/8/2008 |
Q: i cannot get oil to the return line.--- 1.the oil pump gear is worn down about 3 mm(not all the ...
A: You sure you have your measurement right? 3mm is about 1/8 of a inch. Generally, the gear doesnt ...
|
| 2002 FLSTS-I Exaust question | 10/8/2008 |
Q: I have the bike mentioned above and it has true dual exaust. Everyone tells me to get rid of the ...
A: First, keep the true duals. They perform better than stock. On the sound, you can just change out ...
|
| Where to start | 10/7/2008 |
Q: Im in 11th grade and i want to work on Harleys and be a part of building them. I live in Wisconsin ...
A: Since your in school right now, I would take a automotive repair class if you have one. That will ...
|
| Replacing Rocker cover gasket | 10/6/2008 |
Q: I have a 1998 FLSTC Evo. Noticed oil leaking from rear rocker cover. What are the steps necessary ...
A: If you are planning on working on your own bike you should purchase a service manual. It will really ...
|
| rear brakes on a '97 heritage | 10/6/2008 |
Q: i'm looking at this for a friend.no brake action at the rear wheel whatsoever.haven't found a rear ...
A: Follow the brake line from the pedel back and you will see the master cylinder. Remove the cover and ...
|
| hot harley | 10/6/2008 |
Q: Mike, I would like to know if heat will affect the starter? My 95 softail starts fine most of the ...
A: First, check at the battery to make sure the bike is fully charging. At 2000 RPMs you should be ...
|
| oil leaking out | 10/5/2008 |
Q: I have a 1976 sportster 1000. My question is it has been sitting for awhile with no gas in it as to ...
A: There is a ball in the oil pump that is held down with a spring and is suppose to keep oil from ...
|
| S&S carb kits | 10/5/2008 |
Q: Okay looking at the good ol JP cycles catalog and came across these carb kits. There are some ...
A: You need to get the complete kit, otherwise you cant mount it. It will not mount to your intake ...
|
| 1200 sportster | 10/5/2008 |
Q: i have oilcomming out my carbrator, any ideas
A: Your bike is vented to the air filter back plate. When the bike is running air from the motor go ...
|
| extended front end for 1989 FXRS | 10/4/2008 |
Q: I would like to extend the front end of my 1989 fxrs low rider. The stock front end looks pussified. ...
A: You can do that, but all you will do is raise the front end off the ground more. You can add neck ...
|
| When to do a re-build | 10/4/2008 |
Q: I've got an 06 883l with about 11,000 miles on it now. At what point would you consider a re-build? ...
A: A rebuild is when you remove the engine, tear it apart mic all the parts and replace whats needed. ...
|
| Winterizing Bike for Storage | 10/3/2008 |
Q: When preparing to store a motorcycle for the cold winter months around the great lakes, which is the ...
A: Fill the tank all the way. Start the bike, shut the petcock off and let it run until it runs out of ...
|
| 91 FLSTC | 10/3/2008 |
Q: I am replacing my crane coil for the 2nd time, it keeps cracking on me, i think its from the cover.. ...
A: Coils crack from overheating from holding to much juice. Make sure you dont leave the ignition on, ...
|
| 883-1200 conversion | 10/3/2008 |
Q: I own a 1995 883 sportster and thinking of putting a 1200 kit in it. If this is done will the stock ...
A: That is going to depend on what cam, exhaust and air boxyou are running. Your best bet is to install ...
|
| Evo FXR Gearbox? | 10/1/2008 |
Q: Bike specs are: 1986 Evo FXR with stock heads and barrels. Does have an EV35 cam, Mikuni HS40 and ...
A: Your problem is either a broken shifter spring or the spacing on the gear or a bent shifter dog. If ...
|
| engine ping | 10/1/2008 |
Q: I own an 05 FLHTCI with SE Stage 1 pipes, breather,& HD download. no problem. this season, I went to ...
A: Personnally, I dont use either one. I reprogram the ECM that is on the bike. Either one you are ...
|
| is this mechanic going to rip me off? | 9/30/2008 |
Q: I live in a pretty rural area of Massachusetts and getting your bike fixed out here is hell. ...
A: Its really hard for me to say whether he is goign to rip you off or not. I do know some really small ...
|
| winter storage | 9/30/2008 |
Q: hi there mike listen i would like to knowor just put 0my mind at ease do i have to put gas ...
A: you dont have to put any oil in the heads. It will stay oily enough. Start the bike and let it warm ...
|
| 72 ironhead clutch cable | 9/30/2008 |
Q: I just got a chrome primary cover for my 72 sportster. How do I change out the clutch cable, when I ...
A: remove the primary after draining the oil. Screw the adjuster on the cable all the way and remove ...
|
| starter/wide glide | 9/29/2008 |
Q: how do you remove a starter from a 1997 Dyna wide glide?
A: First disconnect the battery. To remove the stater you will have to remove the primary cover, motor ...
|
| 1979 fxs push rod adjustment | 9/29/2008 |
Q: what is the process for adjustment, no nothing about the the engine, so i need help in this area , ...
A: Remove the pushrods and the tappets. At the bottom of the tappet you will see a hole. Push a wire in ...
|
| Harley FLH 1972 clutch | 9/29/2008 |
Q: My clutch on the bike is slipping when giving full throttle/high acceleration around 4000 rpm . Its ...
A: Remove the adjustment from your clutches. Tighten up the nuts ont he springs about 1 to 1 1/2 turns ...
|
| 1994 Fatboy | 9/28/2008 |
Q: Can you please tell me how to remove the speedometer to take a look at the connection? I've removed ...
A: The knob has to come off. There is a small screw inside that has to be removed and then the know ...
|
| 91 fxrs front wheel bearings | 9/28/2008 |
Q: Can you outline the procedure for replacing front wheel bearings, have a front end wiggle. I have ...
A: You need to replace the races, but you will need a race remover to get them out. Once you have them ...
|
| 98 FXD Will not fire. | 9/28/2008 |
Q: Mike, Thanks for your help in the past and hope you can do it again. I replaced the heads and ...
A: SInce you are sure you have fuel being pumped in and a good spark then you need to check the pickup ...
|
| kehin butterfly sceaming eagle carb | 9/28/2008 |
Q: 1985fxwg came with it whats the top airscrew setting turns out from light seat ? float settings?
A: Your starting point for the air/fuel mixture screw is about 1 1/2 turns. Once you get it running and ...
|
| 1978 Shovelhead | 9/28/2008 |
Q: I just purchased this bike and it seemed to run fine. I was riding today and turned right. The ...
A: Ride down the road. When you pull the clutch to shift it always dies? If you ride down the road nad ...
|
| 99' 1340 Evo Motor: How does the starter work? | 9/27/2008 |
Q: Curious on how it engages. I have the starter out but I cannot see the inside details of the casing ...
A: When you hit the starter button the starter relay send power to the starter. the starter solenoid ...
|
| fuel petcock installation | 9/27/2008 |
Q: hey mike, i removed my fuel petcock on a 1976 flh. i know that the large double threaded nut has ...
A: Yes, you turn the nut on the petcock and it threads on both ends at the same time. There is really ...
|
| Clutch Adjustment | 9/27/2008 |
Q: I have a 1990 FXR with an open primary. I recently experienced problems with the bike rolling ...
A: You need to do both. Loosent he cable so there is slack in it, then adjust the clutch itself. then ...
|
| 1989 FLHTC - Oil blowing past Rocker Box | 9/26/2008 |
Q: I recently had the top end of my 89 FLHTC rebuilt. During the break-in period, everything seemed Ok, ...
A: I have never heard of anyone being able to eyeball a warp! You can remove the rocket box and put it ...
|
| 1973? | 9/25/2008 |
Q: I'd like to find out exactly what model they are so as to decide to restore or sell. I have the Vins ...
A: Both bike are 1973 SX 125 harleys. For the parts you would have to do some looking. Parts for these ...
|
| 1989 FLHTC - Oil blowing past Rocker Box | 9/25/2008 |
Q: I recently had the top end of my 89 FLHTC rebuilt. During the break-in period, everything seemed Ok, ...
A: First, you cant mix primary fluid with oil. Primary fluid is synthetic and the oil he used is not. ...
|
| Evo 883 Pushrod | 9/25/2008 |
Q: Mike, I removed the rear rocker cover and assembly to replace the top end gaskets. When trying to ...
A: What you need to do is install the pushrods and before putting the top rocker covers. Rotate the ...
|
| 2005 H.D. Heritage Classic | 9/25/2008 |
Q: How to change oil and where is drain plug? Thanks
A: Start the bike and let it warm up. Under the bike, from the right side of the bike, look at the oil ...
|
| shovelhead electrical problem | 9/25/2008 |
Q: i have a 1981 flh with only 1000 miles on it original owner, i am having trouble keeping it running ...
A: When it wont start, do you have power at the coil hot post? If you pull a spark plug and turn the ...
|
| hand grips | 9/25/2008 |
Q: I have a 2007 Deuce... I would like to change the stock grips. The new grips i have (fm Midwest ...
A: You have to have a grip with two slots, since you have two cables. When you get ready remove the ...
|
| Modulating light | 9/24/2008 |
Q: I have heard that installing a modulating light on a motorcycle can: Burn out the bulb faster. 2) ...
A: the modulating light is designed to make the bike more visable to other drivers. the buld will not ...
|
| headlight/turn signal problem. | 9/24/2008 |
Q: I have a 2000 883 and I'm running my wiring inside the bars. I hooked up the left side and turned ...
A: On a 2000 the front turn signals have a two filment bulb. One it for turn signals and the other is ...
|
| Battery Tender vs. standard charger | 9/23/2008 |
Q: What is a Battery Tender and how does it differ from a standard Sears or Wal-Mart auto battery ...
A: A battery sends a constant current, depending on what you set it to, to the battery. If left on, ...
|
| Sportster | 9/23/2008 |
Q: quick question for you, I was thinking about buying an old sportster from a friend but it has been ...
A: You will probably have to rebuild the motor. Over that amount of time the bearings will rust and ...
|
| 2002 Ultra Classic | 9/23/2008 |
Q: 2 quick questions, first is a heard from a friend that around 25k miles the cam should be serviced? ...
A: Yes, you need to have the rub blocks on the chains checked. If one goes out it will either ruin the ...
|
| Sticky Clutch Plates on 1981 FX Shovelhead | 9/22/2008 |
Q: I have a 1981 FXWG Shovelhead. It all began when the STOCK plates stuck together. Since then I've ...
A: Skuff the clutch disks with some emery cloth. reinstall them after putting a little anti-seize on ...
|
| Jets | 9/22/2008 |
Q: I have a 2001 FLSTC and have added Vance and Hines pipes and a K&N filter kit and have rejetted my ...
A: Your best bet is to get a Dyna-jet kit for your bike. In it you will find the proper jets you need. ...
|
| frt motor mount | 9/21/2008 |
Q: i have a 99 electra glide classic and need to replace the frt motor mount. is it hard to change and ...
A: the stablizer is located at the top of the center of the motor. it is a bar going from the frame to ...
|
| Primary cover removal on 2002 Harley Sportster | 9/21/2008 |
Q: How do you properly remove the primary cover on a 2002 Harley Sportster?
A: You first have to remove the clutch adjuster. remove the derby cover and you will see the adjuster ...
|
| adjusting push rods on 1980 flt | 9/20/2008 |
Q: I had to replace a gasket on my rocker box but in order to remove my rocker boxes I had to remove ...
A: What you need to do is remove the tappet and bleed the oil out of them. remove them and on the ...
|
| 94 sportster knock | 9/20/2008 |
Q: Mike, I have a 94 XL that was just purchased not too long ago that has what sounds like a knock in ...
A: Without hearing the noise, its hard to determine what the noise is. It can be just a piston knock or ...
|
| 2006 1200r ROADSTER | 9/20/2008 |
Q: will i need to have it rejetted for these pipe i did put the 1.75 baffels in the pipes they also ...
A: To remove the clutch cable,loosen the adjuster on the cable os the cable is shorter.Remove hte cable ...
|
| straight pipes for a harley rocker | 9/19/2008 |
Q: I am going to buy a Harley Rocker in the spring. I have seen some really cool looking pipes that ...
A: Your bike comes from the factory running a little lean. Adding "drag pipes" will make it run leaner, ...
|
| case threads striped @ timing hole | 9/19/2008 |
Q: Do you see any other option other then removing the engine and splitting the cases to repair timing ...
A: About the only thing you can do is remove the motor nd split the cases. When you try to drill it for ...
|
| 1995 heritage softtail fuse location | 9/19/2008 |
Q: We would like to know the location of the main fuse box on a 1995 heritage softtail classic and if ...
A: In 95 harley didnt use fuses, they used breakers. They are located either on the front of the back ...
|
| carburetor | 9/19/2008 |
Q: I have a 2008 custom harley chopper with a mukini carb. I went out to shop today and it was leaking ...
A: Make sure when you stut the bike down you turnt he petcock off. It sounds like to float is stuck ...
|
| '85 Sportster | 9/18/2008 |
Q: I have an '85 sportster and i believe the gap in the points closed up on me. It's happened before, ...
A: Your points should be set at .018. remov ethe cover on the points. You will see a rub block on the ...
|
| 2001 sporster transmission | 9/17/2008 |
Q: I am getting a chattering noise in 3td and 4th gear. What could be causing it? Can it lock up when ...
A: You noise might be a bearing going out. I wouldnt ride the bike until you get it repaired. You are ...
|
| stator plug leaking after i had a new drive belt installed | 9/16/2008 |
Q: i seen your answer to the other gentlemen about replacement but i have a 96ss engine with only 2000 ...
A: If the stator plug is leaking there is not much you can do about it. It is a pressed fit and the ...
|
| punched out baffles. | 9/16/2008 |
Q: I punched holes in the baffles on my 06 883l. The baffles are in there, just with three holes in ...
A: The plugs are the best way for you to tell. The only other way is to check the exhaust coming out ...
|
| 1989 FLHS tank and dash | 9/14/2008 |
Q: I'm wanting to update a 1989 FLHS to do away with the dash pod on the handlebars. What year of parts ...
A: You would have to go aftermarket. If you are planning on changing the tank and installing a speedo ...
|
| about harley davidson | 9/14/2008 |
Q: can you help me,,what code/number rear drive belt from Harley Davidson XLH 1100 1987 sporster 30th ...
A: In 87 I dont think a sportster cam with a belt. It might have been converted to a belt. What you ...
|
| 97 EVO | 9/13/2008 |
Q: while had another repair shop look at it he builds racing motors for Harley. the gears moved on the ...
A: It would not be possible for the bearing to move on the shaft since they are pressed in, unless the ...
|
| correct fluids | 9/13/2008 |
Q: Do you recommend using only Harley brand lubes or do you have something better to recommend? Also I ...
A: For you oil, you can use any oil that has SAE one the bottle and is a 20w50. The primary and trans ...
|
| Lowering an Ultra | 9/13/2008 |
Q: I have a 2001 Ultra. I've driven all the touring models and the Street Glide handles great. I ...
A: you can lower it at the rear. There are kits out there you can buy which moves the stock shocks so ...
|
| 1972 FLH clutch cable | 9/13/2008 |
Q: How difficult is it to change a clutch cable on a Harley 1972 FLH Shovelhead. Thank you.
A: Not that tough. loosen the cable at the adjuster on the cable so you have alot of slack in it. ...
|
| 42 MPH | 9/13/2008 |
Q: Got an electrical problem thats giving me fits! Have a Carb fed 2002 classic with an odd electrical ...
A: What you need to do is unplug all the parts that are affected so there is no power to them. replace ...
|
| oil change | 9/13/2008 |
Q: Sir, How do you change the oil on a 2003 Heritage Softail Classic? What is the required amount and ...
A: Start the bike and let it warm up. Under the bike you will find the drain hose coming from the oil ...
|
| Electrical, Engine does not turn over on 1993 softail | 9/12/2008 |
Q: I was riding yesterday on my 1993 softail MooGlide when I revved the engine on 2nd and shifted to ...
A: Ok, what we need to do is get the bike running. First, charge the battery over night. Get a test ...
|
| how to change rear tire | 9/12/2008 |
Q: how do i change a rear tire on a fxstsse 2007.
A: First you have to have a way to jack up the bike. jack it up so the rear tire is just sitting on the ...
|
| clutch hub | 9/11/2008 |
Q: i recently purchased my first harley.and dont know much about them.it is a custom built with a 84 ...
A: the nut is left handed and you will probably need a impact wrench to remove it. The other problem is ...
|
| handlebars and pulls to tke left at 50mph | 9/11/2008 |
Q: Want to change the bars on my 07 Road King. I want a little more pullback because I have a short ...
A: If you are wanting to pull the handlebars back and there is not enough wire then you will have to ...
|
| 74 amf xlh1000 | 9/10/2008 |
Q: I have a 1974 H-D amf xlh 1000 I got it last feburary. The previous owner told me they had just ...
A: If the plugs are sooty black then either your coil is bad or you are running to rich and need to go ...
|
| checking the charging system. | 9/10/2008 |
Q: OK Mike I have a Revtech 100 similiar to a Harley. It have the two wire female connection coming out ...
A: Since you have replaced the regulator and if you know your battery is good, then the only other ...
|
| Harley Dyna Oil Change | 9/10/2008 |
Q: What are the steps to do a complete oil change on a 2006 Harley Dyna??? ANSWER: Start the motor and ...
A: remove he drain plug and drain on the trans. Fill with trans fluid until it is on the full mark on ...
|
| Harley Dyna Oil Change | 9/9/2008 |
Q: What are the steps to do a complete oil change on a 2006 Harley Dyna???
A: Start the motor and let it warm up. remove the drain plug and drain the oil. While the oil is ...
|
| Crankcase breathe oil spillout | 9/9/2008 |
Q: I saw an answer to this problem once before, but need further help. I have a 1976 flh. I have been ...
A: Dont put two balls in, that will only cause problems. take the old ball and install it. Take a punch ...
|
| bad green wire from starter relay to solenoid... | 9/9/2008 |
Q: My 99 night train wouldn't start. Lights and all work fine. Did the voltage check on starter relay. ...
A: Yes, you can reroute the wire. Just make sure its not contacting anything hot. Wire open means the ...
|
| starting issue | 9/8/2008 |
Q: I have a 1994 Harley Fat boy that has recently started to be difficult to start. The bike sometimes ...
A: make sure your battery is good and charged and check both ends of the battery cables for good ...
|
| Oil spitting out of hose | 9/8/2008 |
Q: ive got a 99 ultra groundpounder with a 113 s&s motor.i just bought it and with a new battery and ...
A: When running the bike you cant plug that hose, its a vent for the lower end. there is not much you ...
|
| Slinging Oil | 9/8/2008 |
Q: I have an 06 883L and while riding the other day I noticed oil spots on my right arm and on the ...
A: Sorry, I ment the air filter. Your bike vents in the rocker boxes to the air filter. You can clean ...
|
| Oil Leak | 9/8/2008 |
Q: I have 2006 XL883L, I am getting sprayed with oil on my right shoulder and chest area. We took the ...
A: Under the rocker box there is a rubber disc which is suppose to vent air. It must be bad so a little ...
|
| 2005 FLSTCI | 9/6/2008 |
Q: When I turn the switch on it will start without touching the start button. I just had the fuel pump ...
A: You have juice going to the starter relay which is causing your problem. A pinched wire usually ...
|
| Choke Assembly | 9/5/2008 |
Q: Roy, what is the easiest way to remove and install a choke assembly on a 96 1200C Sportster?
A: You have to remove the carb to get to the choke assembly. It has a 9/16 plastic nut you have to turn ...
|
| Bike stalling | 9/5/2008 |
Q: I have a 2001 FLSTC. About a month ago it started stalling at high speeds. If I drive around 65 ...
A: Another thing to check is remove the air cleaner and when it stalls, shut the petcock off and then ...
|
| Spark Plug got wet | 9/4/2008 |
Q: Before to start thanks for having people like you in the net, :D, I have a sportster 883 and ...
A: The first thing I would check is the intake for a leak. Witht he bike warmed up, spray a little carb ...
|
| ignition coil | 9/3/2008 |
Q: 1987-HD-FLT Any info why an after market coil would go bad in 14 months. Actually, let's say within ...
A: Coils are like anything other electrical part. In time they will fail. As to why it only lasted 14 ...
|
| No rear spark | 9/3/2008 |
Q: I have a 2004 Harley Lowrider Fuel-injection. I have no rear spark (the front cylinder will run), I ...
A: I would start by tracing the wires back from the coil to the ECM to see if you have a pinched or ...
|
| 95 roadking whine | 9/2/2008 |
Q: have a 95 hd roadking.i get a whine from primary side of bike on decel from 40 and above.checked ...
A: I would start by changing the fluids in the primary and trans and see if that doenst help. If you ...
|
| 05 Heritage | 9/2/2008 |
Q: Good morning Mike, 05 Heritage with 10,000 miles. On a recent ride, there was a secondary grinding ...
A: You should have about 1/2 inch play in the primary chain. Check it when the bike is cold. You fill ...
|
| rough running until warm up | 9/1/2008 |
Q: Mike, I have a 1989 sportster with 10,700 mile on it. I have had it for 2 years now. Recently, it ...
A: Sometimes you have to. There are some bikes that are more cold blooded than others and it takes a ...
|
| brake light | 9/1/2008 |
Q: I have a 2003 eltra glide standard it has led brake it is always on or does not come on can not tell ...
A: If the light is staying on all the time check at the handlebar switch. Looking at the brake lever ...
|
| clutch cable replacement | 8/30/2008 |
Q: I have a 2002 Road King FLHR. Would like to put a braided steel cable on but don't know the steps ...
A: Go to the adjuster and loosen it so you have alot of slack in the cable. Remove the pin that hold it ...
|
| will crank but not fire | 8/30/2008 |
Q: I rode the bike yesterday and all was well, parked over night and the next morning would not fire. ...
A: You dont have any power to the coil. With a test light, follow the hot wire from the coil to the ...
|
| overheating ironhead | 8/29/2008 |
Q: I am looking at a79, every time I take it for a test drive It has a hard time warming up -needs ...
A: First thing you need to do is determine why its shutting off. When it shuts off pull a spark plug ...
|
| rear brake light | 8/28/2008 |
Q: Mike I have A 94 Sportster my when I apply the rear brake the light comes on but it is really dim, I ...
A: Run a jumper wire from the hot post on the brake switch to the other post. Does the light get ...
|
| Ignition changes | 8/28/2008 |
Q: Hey Mike, I have recently purchased a custom, well assembled bike that is title as a 95 and I found ...
A: I have found, over the years, that single fire doesnt really help. Besides, you have to change the ...
|
| 1992flhtc stops firing | 8/23/2008 |
Q: PLEASE HELP...Mike i have a 92flhtc that when im riding it ,at any giving time it just quits firing ...
A: If you hear a breaker popping, then you have a short in the wiring. You first need to find the ...
|
| pushrods | 8/22/2008 |
Q: how to adjust screamim eagle push rods on evo
A: jack the bike up and put it in high gear and remove the spark plugs. Rotate the motor so the front ...
|
| 02 Road King Whinning | 8/22/2008 |
Q: I have a 02 Road King Firefighter edition with the 95 big bore kit installed. I recently had the ...
A: Without knowing where is coming from it could be anything from a cam bearing going out to just a ...
|
| 99 RK cuts out then restarts 5-10 min later | 8/22/2008 |
Q: 1999 Road King (43K mi)has recently started cutting out as if it ran out of gas, but restarts ...
A: One of your sensers are going bad and cutting out. The problem is knowing which one it is. What you ...
|
| Third gear | 8/22/2008 |
Q: I am cruising about 40 mph in second gear I shift into third gear and the bike feels like it has ...
A: If you have a choke and a carb, then its not injected. Check the VIN number on the paperwork against ...
|
| 1991 fatboy | 8/21/2008 |
Q: Hey Mike , I've noticed you are amazing at the whole Harley thing so I have a question for you. I ...
A: There is a screen for the lifters to keep dirt out of them. Looking at the cam cover it is a screw ...
|
| transmission leak | 8/20/2008 |
Q: I have 95 Heritage with 68,000. The transmission is leaking towards the inner primary. Is there ...
A: There are two seals on that side of the trans. the main seal and the small seal that is located on ...
|
| RK Noisy Accelerating when hot | 8/20/2008 |
Q: I have a 2005 Road King Classic EFI - all stock. When the weather gets 90F+ and I'm either in city ...
A: It sounds like your bike is getting hot and pinging. The pinging is pre-ignition from the heat. ...
|
| 1981 harley xls generator | 8/20/2008 |
Q: HOW MANY VOLTS SHOULD MY GENERATOR BE PUTTING OUT on my 1981 xls I'M GETTINNING 12.5 ON A MILTON ...
A: Even though you have a new battery, it can still be bad. I have seen batteries right out of the box ...
|
| where to start | 8/19/2008 |
Q: I have a 1948 panhead that has been sitting for quite some time. I have had alot of offers to buy it ...
A: A few things you need to consider. Are you planning on keeping the bike and riding it or selling it? ...
|
| replacing rear brake pads on a 1999 HD softtail | 7/30/2008 |
Q: !!! It worked out well. Now I need to know how to do the rear brakes. Thanks for your help
A: Remove the two bolts that hold the caliber in the bracket and slide the caliber out. You will see ...
|
| 94 Dyna Glide Stator plug wont stay connected | 7/30/2008 |
Q: The stator plug fitting seems to be blocked by the oil filter. It keeps getting loose and ...
A: Over time the rubber on the plugs gets soft and the connections get old and they will come unplug. I ...
|
| 77 sportster | 7/30/2008 |
Q: i may be buying a 77 xlch that is totaly rebuilt with recipts over $8000 is this a good bike the ...
A: The only thing I warn peple about is, when somebody says a bike is rebuilt, who did the work. wa it ...
|
| 1964 Duo Glide | 7/30/2008 |
Q: I have a "64 Duo Glide all original except for an S&S Super E for a carb. I do have the original ...
A: If youa re not getting power to the coil, then follow the wire back to its source. If you have a ...
|
| speedometer on 1999 sportster | 7/28/2008 |
Q: Once in a while my digital speedometer registers about 20 mph under what it should be. Any simple ...
A: You would have to take the speedo in to ahve it checked with a meter. The tranny and primary are the ...
|
| 2004 harley duece | 7/28/2008 |
Q: I have water seeping into my primary case. ANSWER: Do you have any oil leaks from the primary? How ...
A: I am not sure where you would get water in there from. Your primary is closed to the outside, unless ...
|
| chirping noise....... | 7/27/2008 |
Q: I get a strange chirping noise after about 5-6 miles on my bike, sound like it is coming from the ...
A: Noises are hard for me to diagnose on here, due to the fact I can hear them. Take the bike for a ...
|
| brake cylinder gasket | 7/26/2008 |
Q: Hey Mike I have a 96 buell chopper with a sportster engine. My frony brake cylinder leaks because ...
A: If you have a stock master cylinder you can get one from a dealership. take the gasket in and you ...
|
| fuse panel | 7/26/2008 |
Q: I have a 1993 sportster and the right turn signal is not working. The left one works fine. I am ...
A: You donthave fuses, you have breakers. If the left turn signal is working then its not the breaker. ...
|
| 2005 Elec Glide Standard Fuel Inj. | 7/26/2008 |
Q: I installed a chrome engine kit[OEM Harley].I was hesatant on the rocker covers.But I read your ans. ...
A: What you need to do is raise the rear end and remove the spark plugs. Remove the clips from the ...
|
| wireing | 7/26/2008 |
Q: I have a 88 1200 sportster and it has a Ultima wireing system, I cant get my high beams to come on ...
A: I am not familer with the Ultima wiring, so I dont know if its color coded like stock. Check the ...
|
| front brake pads... | 7/25/2008 |
Q: I replaced the pads on my front braks on my 2001 STDeuce. I was able to pry the old pads open to ...
A: Dont try to bleed them before pumping them up. Keep pumping the lever. It takes quit a while, due to ...
|
| Tearing up solenoids | 7/25/2008 |
Q: I am also from Ohio, Cleveland area. Own a late 1984 fxr evo. I too have a problem with the starter ...
A: Here is somthing that seems to work. remov ethe solenoid and spring. Install a spacer inside where ...
|
| 1997 Fatboy | 7/25/2008 |
Q: I bought new pegs and controls to replace my footboards will I need a new brake line going to the ...
A: On your brake line you would have to do some measuring to see if its gong to be the right length. ...
|
| 2006 1200r ROADSTER | 7/25/2008 |
Q: I BOUGHT THIS BIKE ABOUT A MONTH AGO IT HAS 4500 MILES ON IT AND WHEN I FIRST GOT IT WHEN SHIFTING ...
A: You dont have a 02 senser on your bike, unless one was added by the owner. In order the check the ...
|
| 08 harley tank removal | 7/25/2008 |
Q: i have an 08 fxstc. i am removing the tank, is the crossover line the mechanism that is located ...
A: The cross over is the line in the front that equalizes the tanks. Make sure you drain the tank. When ...
|
| Sportster won't start | 7/24/2008 |
Q: Mike, I have a 95 Sportster 883 deluxe. Unfortunately, due to an injury I was not able to ride for ...
A: You can get carb cleaner at any automotove store and a rebuild kit at a motorcycle shop. Its not ...
|
| 99 fxd brake light | 7/24/2008 |
Q: I was wondering is it possible for both brake light switches to go out at the same time or is there ...
A: Check to see if you have a broken or short in the wiring. Go to the brake switch for the rear and ...
|
| shifting gears | 7/24/2008 |
Q: I have a 94 Dyna Wide Glide.It has 5,000 mi on a totally rebuilt engine.And also a 5,000 mi on a new ...
A: Its probably not your clutch or it would be tough to shift in all gears. I would first would adjust ...
|
| oil leak on s&s | 7/23/2008 |
Q: I have an s&s super stock on my bike that has devoloped a oil leak. I had not run my bike for ...
A: Your bottom end of the motor might have filled with oil while sitting and its dripping out the vent. ...
|
| chirping type noise | 7/22/2008 |
Q: i have a 2004 road king police. i put on v&h mufflers and noticed an annoying chirping type noise in ...
A: Generally, if you hear a chirping sound at the motor, its a blown head gasket. Since you say its at ...
|
| how to adjust jets? | 7/22/2008 |
Q: I've read this answer by you:(Its not your air/fuel misture screw that is the problem. the air/fuel ...
A: Your jets might not be the problem. I would do a OHMs test on the coil and plug wires to makesure ...
|
| 68 Sportster Paint Schemes | 7/22/2008 |
Q: Trying to restore my first Harley (a 68 Sportster XLCH). Can you assist me with colors and paint ...
A: they had several colors for that year. I would suggest going to a book store and checking the books ...
|
| chirping type noise | 7/22/2008 |
Q: i have a 2004 road king police. i put on v&h mufflers and noticed an annoying chirping type noise in ...
A: SOunds on here are hard to diagnose, since I cant hear them.Does the sounds happen all the time on ...
|
| rake on my 75 sporster | 7/21/2008 |
Q: i have a 33 degree on a 1975 hardtail sporster.it is 1.1/2 inches off the ground.what lengh fork ...
A: What you need to do is take a measurement from the axle to the front of the bike, inline with the ...
|
| leak | 7/20/2008 |
Q: I have a strange leak I think it is coming from my trans. I have a 1980 flh.There is always a small ...
A: Your leak is either the seal on the back of the inner primary where the trans shaft goes through, or ...
|
| Crankcase Breather tube | 7/20/2008 |
Q: I have a 73 XLCH iron head with only 14,000 miles on it.About 7 years ago(4000 miles ago)I redid the ...
A: You will have pressure coming out of that tube, that is how the bottom end vents. With the age of ...
|
| 1990 Sportster cuts out while driving | 7/19/2008 |
Q: My 1990 Sportster has recently started cutting out on me while driving. For the most part, I could ...
A: If your lights are flickering then you have a short int he wiring. You need to get a test light and ...
|
| 91 sportster | 7/18/2008 |
Q: I'm sitting here with my manual on the driveway with a new starter in my 91 Sportster. I'm really ...
A: Make sure your battery is fully charged or it wont turn over. If you sheared the rivets the ring ...
|
| 88 sportster no spark | 7/18/2008 |
Q: hey there, i read a little bit but my question still remains...my bike has been running great, this ...
A: Start by seeing if you have power to the ignition switch. If not then trace the main wire back to ...
|
| vapor lock | 7/16/2008 |
Q: I have a 1980 sportster ironhead with a S&S carb. when the bike gets hot it seems to vapor lock, it ...
A: First, after you shut if off and it wont start, pull a spark plug and see if you are getting spark. ...
|
| 76 ironhead wrist pin bushings | 7/16/2008 |
Q: mike, i am having to do a total topend rebuild on my 76 iron head due to the front cylinder chugging ...
A: If the wrist pin bushing has turned the hole for the bushing in the rod migth be to big for the new ...
|
| Old Stroker | 7/16/2008 |
Q: I'm tring to fire up a 1974 Sporty that has a S&S stroker kit, I've tore apart and cleaned and the ...
A: The screw to idle the bike turns outward to idle it down. Also, your cable might be to tight and ...
|
| 2006 1200r ROADSTER | 7/15/2008 |
Q: I BOUGHT THIS BIKE ABOUT A MONTH AGO IT HAS 4500 MILES ON IT AND WHEN I FIRST GOT IT WHEN SHIFTING ...
A: the drain for the primary is below the primary cover, close to the back. I would drain it and check ...
|
| 1988 harley starter problems | 7/15/2008 |
Q: 1988 harley, now my buddy replaced the sileniod while it was still hooked up to the battery (sparks ...
A: The only other thing it can be is the starter button is stuck or the starter relay is stuck in the ...
|
| low mileage bike | 7/14/2008 |
Q: I recently found a 1998 Fat Boy for sale. It has 1600 (that's correct 1600, not 16000) miles on it. ...
A: Its really hard to say on a bike that has been sitting if seals and gaskets ar going to leak. I have ...
|
| sportster engine popping and sputter | 7/14/2008 |
Q: I have a '96 sporster with an 1100 evo engine, drag pipes, and stock air filter, and don't know what ...
A: There are about 12 tests to check the modual and pickup. It would take me forever to tell you on ...
|
| cultch cable repair | 7/14/2008 |
Q: How do I replace the clutch cable on my I think 1980 XLH I say I think as the ID number starts with ...
A: In order the repalce the cable you have to remove the primary cover. You have to adjust the cable so ...
|
| Battery Tender | 7/13/2008 |
Q: My battery was drained beyond the point it will start without assistance. I have a Battery Tender ...
A: You need a pigtail for your tender to attach to the battery. Attach the pigtail to the battery and ...
|
| broken flange primary side lower case | 7/13/2008 |
Q: I have a Harley 1985 FLHT and the flange on the lower case that seats to the inner primary is broke ...
A: I have heard of them, but dont know wh sells them. In order the do the repair and remove the flange ...
|
| My 73 Sporty won't start | 7/13/2008 |
Q: I rode my 73 sporty (trike) around the block and it ran great and then shut it off for a couple ...
A: First, you need to check to see if its a ignition problem or a gas problem. Look down the throat of ...
|
| starter | 7/13/2008 |
Q: My 91 sporster started fine in the morning then after two stops, just whined when I tried to start ...
A: Pull your primary cover and check the ring gear on the clutch to see if its damaged. You can bump ...
|
| 89 FXR OIL AND ELECTRIC PROBLEM | 7/13/2008 |
Q: i tried to restart it but it started to knock so i stoped i'm guessing it overheated so i took off ...
A: If you dont have power to the coil then you will have to trace the wire back to its sourse. The coil ...
|
| wiring harness | 7/13/2008 |
Q: I am trying to install an ultima complet harness in my 75 ironhead. I got a little lost with the ...
A: I have never used of of harnesses you are talking about so it tough for me to comment on it. Your ...
|
| shovel head | 7/13/2008 |
Q: what jetting sould be used on e shorty s&s carb for 3 5/8"by 4 1/4" stroke drag pipes?
A: There is no certain jet, its what works with your bike and your setup. Start by turning off the ...
|
| 75 ironhead sporty problems | 7/12/2008 |
Q: I just bought a 75 xlh 1000 and when I got it started something was slapping in the motor. I ...
A: Metal shavings are not good. The motor will have to be torn down and inspected to see what the ...
|
| Crane HI-4 | 7/12/2008 |
Q: I have an 87 Custom Softtail and I installed a Crane HI-4 ignition & coil and I need to adjust the ...
A: Once you have to static timing set (motor at rest) then time it with a timing light. You have to ...
|
| !980 Fxwg 1200 Rocker covers,wiring | 7/12/2008 |
Q: First you have a great site,Learned more from your answers than my clymer manual.My last bike,bought ...
A: I doubt if tighting the bolts will stop the leak. Your going to have to replace the gaskets. Yes, ...
|
| Oil from carburetor 1993 FLHTC Evo | 7/12/2008 |
Q: The engine has a cam installed. Also has a S+S oil pump installed Has a aftermarket air filter. ...
A: Check your pumper on your carb. Might not be punping enough fuel when you get on it As to your oil ...
|
| 2005 dyna forks | 7/12/2008 |
Q: mike,i own a 2005 fxdi superglide,i just started noticing something unusual in my front suspension.i ...
A: There is a large spring in each fork that is there for the spring in each fork. You might have a ...
|
| clutch basket | 7/11/2008 |
Q: i've been breaking my 1-1/2 inch primary belt.motor pully is new, clutch pully looks real good.i ...
A: The clutch basket you have is probably a aftermarket one, since I dont think harley made one for ...
|
| 1974 XLCH 1000 | 7/11/2008 |
Q: I run high test through my bike because that is what everyone I ride with does. In 1974, I believe ...
A: I know bikers who add lead additive and ones that do not. There is no difference in the running of ...
|
| Starter run on 1987 FXSTC | 7/10/2008 |
Q: I hope you can help. 1987 FXSTC starter motor starts running after riding for about 20 minutes, only ...
A: Even is your stator was bad that wouldnt make your starter engage. You can test your stator by doing ...
|
| heritage | 7/9/2008 |
Q: I asked you a question earlier about my alarm sys- got that fixed- now I have something shorting out ...
A: All your switches receive power fromt he same place, so what you have to do is start tracing out the ...
|
| 91 FXRS POOR RUNNING | 7/9/2008 |
Q: I run a 91 fxrs-c with se11 cam dyno-jet carb kuryakyn filter vance&hines short shots and have just ...
A: When you changed your belt and pulley, you changed your final drive ratio. Now you need more RPMs to ...
|
| Stator Replacement | 7/9/2008 |
Q: I HAVE AN 84 1340 EVO ELECTRA GLIDE I WAS WONDERING IF YOU COULD TELL ME HOW TO CHANGE THE ...
A: In order to replace the stator you have to remove the primary cover, motor sprocket, clutch basket ...
|
| Starter run on 1987 FXSTC | 7/9/2008 |
Q: I hope you can help. 1987 FXSTC starter motor starts running after riding for about 20 minutes, only ...
A: take your bike for a ride. When you hear the starter running, quickly check the big solenoid posts ...
|
| Harley unused three years | 7/8/2008 |
Q: I've got 98 SuperGlide, haven't used for three years has about 20K miles. Got sick had no garage so ...
A: Sitting that long, the battery is probably no good, so start there. Drain all the fluids and ...
|
| motorcycle running rich | 7/8/2008 |
Q: I have changed the plugs three times now on my 1979 Low Rider (1200) and bike runs fine for a few ...
A: If you have to charge the battery all the time then its time to replace it. It might not be holding ...
|
| 01 FXDL Starter removal | 7/8/2008 |
Q: Go to start this bike and it sounds like two gears crashing into each other.At times it will catch, ...
A: If you plan on working you your bike your best bet is to get a service manual. It will really help ...
|
| backfiring | 7/8/2008 |
Q: I've read the recent answer to the backfiring question and my harley model is a 2001 fxs series and ...
A: You want to know the OHM reading for your bike. For what part? OHMs is a measure of resistance in ...
|
| please resend answer | 7/8/2008 |
Q: Mike I apologize, but the email I submitted when I initially ask the below question was incorrect. ...
A: Look behind the choke knob and you will see a round knurled plastic nut. Tighten it a little and it ...
|
| 2001 Road King Classic, Sputtering/ Missing | 7/7/2008 |
Q: I have an 2001 Road king classic(with EFI) that runs great except for a recent problem I have ...
A: I would start by checking the primary chain to make sure its not to tight or to loose. I dont think ...
|
| backfiring | 7/7/2008 |
Q: I've read the recent answer to the backfiring question and my harley model is a 2001 fxs series and ...
A: SInce you have a carb, then its not fuel injected. Remove the carb and turn it over. Looking at the ...
|
| Checking stator and rotor | 7/7/2008 |
Q: Mike - I have a 1981 FXE/F, bought new back in '81. Apparently, I had a bad voltage regulator for ...
A: When you start the bike you should get around 13.5 volts at the battery. If not then do a OHMs test ...
|
| 1966 XLCH | 7/7/2008 |
Q: This bike caught on fire before I got it.Wires & oil lines are gone.Where can I get diagrams to ...
A: Get a service manual and it will show the wiring diagram and oil line routing. I cant tell you how ...
|
| zenith carb adjustment | 7/6/2008 |
Q: how do i adjust the zenith carb on my 84 sportster which is the idle and which is the intermediate ...
A: The idle screw is located close to the throttle cable where is attaches to the carb. The air/fuel ...
|
| motorcycle running rich | 7/6/2008 |
Q: I have changed the plugs three times now on my 1979 Low Rider (1200) and bike runs fine for a few ...
A: To do a leakdown test you have to have a leakdown tester. What youa re doing is putting pressure on ...
|
| 76 sportster pist-off | 7/6/2008 |
Q: I just got around to inspecting inside the spark plug holes on the 76 sportster that had died and ...
A: A hole in the piston can be caused for overheating, pre-detanation or the valve hitting the piston ...
|
| cam sensor wires | 7/5/2008 |
Q: Mike, It's me again. So you are telling me that a stock HD cam sensor cannot be run directly, one ...
A: The stock cam senser checks to see where the cam is whne the motor is turning. It has to send a ...
|
| 85 fxrs backfiring and rocker cover leaks | 7/5/2008 |
Q: I have an 1985 fxrs stock except for the sports style intake with the "o"rings. Bike has approx. ...
A: Your beat bet is to order a top end gasket kit and that will give you all the gaskets you need to ...
|
| sportster head gaskets | 7/4/2008 |
Q: What is the easiest way to change the front head gasket on my 2000 sportster 883? do I need any ...
A: Your going to have to remove the tank, rocker covers and head to replace the gasket. You will also ...
|
| FLH 1200 year 72 smoking | 7/4/2008 |
Q: At slow idle my bike is smoking (blue greyish) from only cylinder 1 exhaust pipe (smells like oil ...
A: Blue/grey smoke would indicate that you are burning oil. the two places you can get oil from are the ...
|
| clutch | 7/4/2008 |
Q: I have an 1980 FLH. I set the clutch up as per the repair manual. Now at a stop light the bike ...
A: Put the 3 nuts back where they should be. Go to the adjuster in the center and adjust from there. ...
|
| no power in 4th gear | 7/4/2008 |
Q: I am back. I took the carb apart again on my 83 sporty 1000 keihin carb. Found a rubber ripped and ...
A: That knob your are refering to on the handlebar is a tentioner for the throttle. It might not be ...
|
| Keith Black Pistons | 7/4/2008 |
Q: How do you tell where the front is?
A: I dont use keith black pistons so it going to be tough for me to tell you which way they go. If you ...
|
| xl 1200c carb issues | 7/3/2008 |
Q: I purchased a 2004 xl1200c with screaming eagle pipes and a free flow air filter. I was ...
A: Installing the carb kit is not hard at all. I am surprised that there are no instructions that came ...
|
| backfire and puttering | 7/3/2008 |
Q: where can I find the air/fuel mixture screw? Intermediate jet? float? On my 2001 fxs. thank you ...
A: The air/fuel mixture screw is located at the underside of the carb. There is a plug covering it, so ...
|
| Trouble shooting a 1999 1200c Sportster | 7/2/2008 |
Q: This just started a couple days ago, but as I'm riding i have noticed a miss in the motor. It ...
A: First you need to determine if your miss is electrical or fuel problem. Take the bike for a ride and ...
|
| charging problem | 7/2/2008 |
Q: i have a 2003 harley dyna super glide. my battery keeps loosing it's charge, as though the charging ...
A: Since your know your battery is good then its either your stator or regulator. You dont have a ...
|
| Front and rear brakes | 7/2/2008 |
Q: I recently had my tires changed with no brake repair work done. After the tires were changed I have ...
A: When they changed the tires they probably opened the pads in the caliber to make it easier the get ...
|
| 1986 soft tail custom front end wobble | 7/2/2008 |
Q: my front end appears to wobble at high speeds. not a whole a lot; but slightly, nonetheless. Why? ...
A: If it were me I wouldnt ride the bike until its repaired. You might go into a wobble you cant get ...
|
| 91sporty | 7/2/2008 |
Q: S&S super E carb with drags.set the carb 1 1/2 turns on air fuel mixture,2 turns on pump screw,and ...
A: If your bike has been running fine before this happened then I would start by doing a OHMs test on ...
|
| backfiring | 7/2/2008 |
Q: The other day, after no changes or adjustments of any kind, as I was riding approx 35 mph my ...
A: Remove the coil. There are two posts on the coil where the wires go. With a OHM meter test from post ...
|
| brake light | 7/1/2008 |
Q: I have a 1984 harley sportster. when i turn the key the brake light comes on as if the brake is ...
A: Check your handlebars where the brake lever is. You will see that the brake lever and the throttle ...
|
| carb Setting | 7/1/2008 |
Q: I changed my top end gaskets and piston rings this past winter. My bike was back firing and chugging ...
A: It sounds like you need to remove and rebuild your carb. You have some dirt in the jets and that is ...
|
| paint | 7/1/2008 |
Q: just bought a new Harley & got a good price because the paint has swerl marks & lite scratches , can ...
A: Your best bet is to got a buffer and some light rubbing compound and buff them out. There really ...
|
| wheel bearings | 7/1/2008 |
Q: I have a 1983 xlh sportster. I need to replace the front wheel bearings. Do I have to take the ...
A: No, once you have the wheel off pull the seals out and the wheel bearings will come out. If you are ...
|
| harley problems | 7/1/2008 |
Q: i have 2001 fatboy efi and security system, change battery now it starts and runs about 2 seconds ...
A: About the only thing you are going to be able to do is take the bike in and haave a dianostic run on ...
|
| 02 1200 SPORTSTER | 6/30/2008 |
Q: I HAVE A 02 SPORTSTER AND WAS TOLD BY TWO GUYS THAT THE FRONT CYLINDER IS RUNNING LEAN DUE TO THE ...
A: Since you only have one carb and one intake you cant hae one cylinder running lean, unless you have ...
|
| 73 sportster oil out breather tube | 6/29/2008 |
Q: I have a 73 sportster that i have rebuilt. it now has about 2800 miles on it. I have ported and ...
A: Your having blowby out the breather. You never said what cams you have, but if you really have a ...
|
| clutch adjustment...62 panhead kicker | 6/29/2008 |
Q: when adjusting the clutch it either is dragging to where the trans won't engage, and if it does, it ...
A: Heres hou I do the adjustment. Make sure your pressure plate on clutch is 1 3/16 from the back of ...
|
| Main circuit breaker | 6/29/2008 |
Q: I have a 2000 Heritage with 106 cube S&S bottom end. I'm having electrical problems with the main ...
A: Since you have changed the parts you described the only thing it can be is there is a short in the ...
|
| Speedo Housing -79 FX Shovel | 6/29/2008 |
Q: I am rebuilding a 79 shovel and the speedo housing located on the left side of the front axle ...
A: The housing you are refering to is the speedo drive. There is nothing pressed on the axle. That is ...
|
| 96 EVO | 6/28/2008 |
Q: I,m putting adjustable push rods (Crane) in and can not see the cam (lower end is closed)to find the ...
A: Put the pushrod in and put a clothspin on it. Rotate the motor and you will see the clothspin go up ...
|
| hard to get neutral | 6/28/2008 |
Q: I have an ultra 08 only 400 miles on it,and am having trouble getting neutral(takes 2 or 3x)when the ...
A: As your bike breaks in it will get easier to get into netural. Where the dealer adjusted the trans ...
|
| Gear Box Whine | 6/27/2008 |
Q: Just took over my Dad's 96 Sportster. Late last fall he had the stator replaced to keep the battery ...
A: First thing I would do is replace the fluid and then test ride it. When changing the stator you dont ...
|
| Harley FLH - misfiring | 6/27/2008 |
Q: Have a HD FLH year 72 wit SS Super B carburettor on. At low speeding like 20 - 40 miles pr. hour and ...
A: The air/fuel misture screw only affect the bike at idle. Check for a intake leak by spraying some ...
|
| throttle cable instalation | 6/26/2008 |
Q: 1993 Soft tail I am having trouble installing new throttle and idle cable on S&S Super e carb. Do I ...
A: You have to install the cables in the trrottle lever first, before installing in the carb. Adjust ...
|
| oil in the air breather | 6/26/2008 |
Q: just bought 95 ultra classic.put six hundred miles the bike has 45.000 miles. supposed to just ...
A: Your oil pressure is fine. You are getting oil in the breather from the rocker boxes. You bike ...
|
| 04 Harley Davidson 1200 Sortster Custom | 6/25/2008 |
Q: I have a 04 Harley that needs the primary chain adjusted. It is rattling and hitting the primary ...
A: Yes. Adjust it from under the primary cover. There is a bolt with a locknut on it. remove the small ...
|
| low charging | 6/25/2008 |
Q: 2003 full bagger, low or no charging from alt. or should i say at battery. how to check voltage ...
A: First, test the stator at the plug for a short with a OHM meter. Bothe wire to ground and then wire ...
|
| Dot 5 Brake Fluid | 6/24/2008 |
Q: Have 2006 Custom Sportster, brought in for 25,000 service. Was told I have dot 4 and dot 5 brake ...
A: You need to use DOT 5 fluid. The dot 4 didnt hurt anything and you dont need to replace the parts ...
|
| 2001 Sportster Not charging | 6/24/2008 |
Q: Can you tell me what the most likely problem would be. I just bought a new battery thinking that it ...
A: The stator is located inside the primary. Follow the wires from the regulator and you will see a ...
|
| 04 Roadking | 6/24/2008 |
Q: i have an 04 roadking...it came up with a PO108 maf code and PO113 IAT temp code..is there an easy ...
A: Have a shop do a dianostic test on the bike. Even though you got codes, its not tell you if the part ...
|
| 1980 HD Sturgis Clutch Adjustment | 6/23/2008 |
Q: I am trying to adjust my cluch assy on my 1980 Sturgis with great difficulty. Is there specific ...
A: First, put ome slack in the cable by adjusting it shorter. Go tot he clutch and loosen the locknut ...
|
| oil light | 6/23/2008 |
Q: i have a 2003 road king, the oil light just came on and the bike started to make noise in the rear ...
A: If the oil light came on then you either lost oil pressure or the light is bad. Do to the noise you ...
|
| 2001 Sportster Not charging | 6/23/2008 |
Q: Can you tell me what the most likely problem would be. I just bought a new battery thinking that it ...
A: What you need to to is first, check at the battery with a volt meter when the bike is running and ...
|
| 88ci to 95ci | 6/23/2008 |
Q: I am wanting do get better performance out of my 2000 FLHTC (carb) bike, I was looking into a 95ci. ...
A: I would start by changing hte cams out for the gear dirven cams. Then you dont have to worry about ...
|
| head light | 6/23/2008 |
Q: thought about buying a new wiring harnes
A: Check at the plug with a test light. You should have one post at the bulb for high beam, low beam ...
|
| Oil Change | 6/23/2008 |
Q: I want to start changing the oil in my 1990 heritage softail myself. I was looking for instruction ...
A: Look under the bike on the right side under the bike, and you will see a line off the oil tank that ...
|
| 85 FXRS Rear brakes locked up. | 6/23/2008 |
Q: After 12 years in storage, I re-activated my FXRS. The rear caliper was locked open, (no braking ...
A: Your master cylinder is probably bad. I would replace it instead of trying to rebuild it. Over time ...
|
| choke cable | 6/23/2008 |
Q: I have a stock 1990 sportster . The choke knob is broken. how to replace the choke cable? Do i have ...
A: First, you have to remove the carb. The choke cable is screwed into the carb. You dont have to ...
|
| oil leak | 6/22/2008 |
Q: i own an 02 sportster 883c,changed the oil about a month ago. had no problems till today i noticed a ...
A: Your breather goes to your air cleaner and sometimes with the air a small mist of oil goes with it. ...
|
| custom headlight removal | 6/22/2008 |
Q: I am trying to remove the slip ring off the headlight to get to the wires to wire the ...
A: I am not sure how it removes, but usually that type pops off and is just attached by a clip. ...
|
| Harley cables | 6/21/2008 |
Q: I have replaced the grips on my "o7" ultra classic. The throttle control on the right side feels ...
A: One cable is throttle and the other is return. There should be adjustments located close to the ...
|
| derby cover | 6/21/2008 |
Q: I recently changed my derby cover on my 06 xl sportster,but have now noticed a leak.how do i stop ...
A: Pull the derby cover and make sure the gasket surface is clean. Check the gasket for damage and if ...
|
| 1974 ironhead sportster clucth problem | 6/20/2008 |
Q: I'll ty to be as thorough as possible here to give you an idea of what I am facing. Sorry in ...
A: It appears that the clutch is engaged when you have the cover on, so the problem sounds like inthe ...
|
| 1979 Sportster xlh 1000 Rim sizing | 6/20/2008 |
Q: We have the original mag wheels, 19"front, 18"rear, on our bike now. My husband would love to get ...
A: What you need is wheels that will fit a 78 to 83 sportster. Going with different years you will get ...
|
| 1984 FXSB shovelhead ignition timing and pushrod adjustment | 6/19/2008 |
Q: Proper method of timing ignition system on a 1984 shovelhead with electronic ignition and the proper ...
A: To time the bike you need a timing light. Start the bike and at the timing hole shoot the light and ...
|
| lower and rake | 6/19/2008 |
Q: How many degrees of rake do I need to put in my front end for every inch I lower the rear end in ...
A: In order the rake the frame you have to cut it, bend it and weld it back. You can get pre raked ...
|
| Harley Frame | 6/19/2008 |
Q: Mike in `93 I bought a `73 shovel from a guy in Ca. He builds bikes. It was reg. in Ca. as a `73 HD ...
A: I am not sure how or what they are using to tell what they think is the difference in the frames. I ...
|
| 1990 flstc running lights, headlight and tail | 6/18/2008 |
Q: My headlight, running lights and tail quick working. The blinkers, brake lights, neutral and oil ...
A: You have breakers, not fuses. Look under the left cover and you will find them. Make sure you have ...
|
| 1974 HD Sportster highway pegs | 6/18/2008 |
Q: I am getting ready to mount higway pegs to a 1974 Sportster and I forgot to order the extended ...
A: You can just use a bolt from a hardward store. It is nothing special. I cant tell you the size, ...
|
| 1989 sportster 883 hugger | 6/10/2008 |
Q: i have a sportster that my wife used to ride then stop back in "04" so i put gastabil in tank and ...
A: What has happened is oil has weeped into the bottom end of the motor. When you started it the oil ...
|
| 82 FLT Chain Boot Removal Tran side | 6/10/2008 |
Q: I am removing the 4 enclosed-chain-boot allen bolts from a 82 FLT Tour Glide so I can remove the ...
A: I have worked on these before and I know they are a pain! I think that is why harley only made them ...
|
| Oil leaking from the carb | 6/10/2008 |
Q: I have a '01 Sportster that was an 883 but was converted to a 1200. Recently oil has been coming out ...
A: Your bike vents air to the air filter from the motor. Its when the pistons go up and down and makes ...
|
| FLHS valve train noise | 6/10/2008 |
Q: I've got a 91 FLHS that I bought recently. It has tappet noise. I adjusted the adjustable push ...
A: The tapping is from the valve lash at the rockers, not the lifters, so you will hear the noise more ...
|
| generator | 6/9/2008 |
Q: I have a 1975 sportster,my generator light came on,I took the generator off.It was full of oil,I ...
A: Oil is probably getting into the generator from a bad gasket where it mounts to the motor. There is ...
|
| 74 xlch main drive shaft nut | 6/9/2008 |
Q: I can not remove the main drive shaft nut from my 74 XLCH. I was told a different thread pattern by ...
A: Never heard of one that wouldnt come off with a impact wrench, due to the fact that is how I remove ...
|
| 1981 FLTC | 6/9/2008 |
Q: 1981 FLTC SEEMS TO HAVE AN IGNITION PROB, RUNS GOOD TILL WARMED THEN WHEN YOU ROMP ON IT IT SPUTTERS ...
A: The coil as well as the ignition are not prone to shut down or cause a sputter when you just romp on ...
|
| 1981 FLTC | 6/9/2008 |
Q: 1981 FLTC SEEMS TO HAVE AN IGNITION PROB, RUNS GOOD TILL WARMED THEN WHEN YOU ROMP ON IT IT SPUTTERS ...
A: A couple of things would cause your problem. If it was your ignition, it would happen all the time, ...
|
| FLH Harley year 1972 battery drain | 6/9/2008 |
Q: I ve got problems with holding charge on my battery. After a long ride here the other day , battery ...
A: At the stator you should have 50-100 ac volts at the white to white wire. At the blue to red wire ...
|
| 1986 Harley 883 Alternator Magnets | 6/9/2008 |
Q: I recently learned from the Internet that the alternator's permanent magnets inside the clutch ...
A: the magnets becoming detached is not really common, but it can occure. Nothing is bullet proof and ...
|
| FLH Harley year 1972 battery drain | 6/8/2008 |
Q: I ve got problems with holding charge on my battery. After a long ride here the other day , battery ...
A: You should have a constant voltage at the battery of around 13.5 to 14, so you have a fault at ...
|
| shovelhead ingition problems | 6/8/2008 |
Q: I have a 1975 flh dual fire points ingition.I keep losing fire on the rear cylinder. i checked the ...
A: the only thing that can cause your problem is either a bad coil, bad plug wire, bad condenser or ...
|
| 1200 xlc custom | 6/8/2008 |
Q: Mike i have a 2005 1200 xlc with screamin eagle pipes and air cleaner installed by the harley ...
A: Generally, when you change pipes and air cleaner you go leaner, but the shop might have jetted to ...
|
| HOW TO CHANGE CLUTCH LEVER | 6/8/2008 |
Q: MIKE I JUST BOUGHT A 2007 FLSTSC CAN YOU PLEASE PLEASE TELL MY HOW TO INSTALL A NEW CLUTCH LEVER ON ...
A: Go to the cable and loosen the locknut and turn the adjuster so the cable is shorter and it has ...
|
| adjusting lifters | 6/7/2008 |
Q: how do you adjust the lifters on a 84'shovelhead 1340 the are crane adjusting lifters tappets
A: remove the tappets and bleed them. To do this, push a stiff in the bottom to move the ball in there ...
|
| 1974 Sportster | 6/7/2008 |
Q: I've recently started going through an old iron head sportster(1974). The bike was "supposedly" ...
A: Your breather gear not being timed correctly will not keep it from starting, it will just smoke like ...
|
| pushrod clips | 6/7/2008 |
Q: I have a 2008 96ci flhx, I installed new kuryakyn tappet block cover but can't get pushrod clips ...
A: Make sure the bottom of the cover is all the way in the o-ring and make sure its all the way in the ...
|
| FLH Harley year 1972 battery drain | 6/7/2008 |
Q: I ve got problems with holding charge on my battery. After a long ride here the other day , battery ...
A: First, after you get the battery charged, start the bike and at the battery test what the voltage ...
|
| no start | 6/7/2008 |
Q: I have a 1978 flh 1200 shovelhead. Wont turn over when I push start button and I am hearing an ...
A: make sure you have a good battery. Check at the starter button to make sure you have power on both ...
|
| 1995 Harley XLD 883 | 6/7/2008 |
Q: When I turn on the key switch the oil light and neutral light won't come on and won't activate the ...
A: What you need to do is first determine if you have power going away from the key switch. Using a ...
|
| Dot 5 Brake Fluid | 6/5/2008 |
Q: Have 2006 Custom Sportster, brought in for 25,000 service. Was told I have dot 4 and dot 5 brake ...
A: Just because your brake fluid is brownish doesnt mean that Dot 4 is in it. Dot 4 and Dot 5 do on ...
|
| Tank removal | 6/5/2008 |
Q: How do I remove the gas tank from my 06 Street Bob? ANSWER: carberated or fuel injected? Mike ...
A: Drain the fuel tank. Disconnect the fuel lines. they are attached like a air fitting. Pushup and ...
|
| Intermittent spark | 6/4/2008 |
Q: I have an 85 XLH that has intermittent spark and it will spit thru the carb occasionally. I ...
A: The only thing that would cause your problem is a loss of power to the coil, if you are loosing ...
|
| 2002 FATBOY | 6/4/2008 |
Q: I BOUGHT A NEW FUEL TANK.HOW HARD IS IT TO TAKE OFF THE OLD TANK AND INSTALL THE NEW TANK.I TOOK OFF ...
A: You have to remove the plate you are refering to. Inside is the fuel pump and the wiring for the ...
|
| 2000 1200 sportster | 6/3/2008 |
Q: Mike: I have a 2000 sportster 1200. I replaced the stock air filter with a full mesh air filter, now ...
A: Dont close those off, theya re breather hoses. You probably leaned out your bike by changing to a ...
|
| 02 road king valve adjustment | 6/3/2008 |
Q: I keep hearing a clatter when I ride my 02 road king, I put new adjustable push rods in but this did ...
A: If you have adjustable pushrods you can adjust the valves. Jack the bike up and remove the spark ...
|
| 96 Wide Glide - Starter Clutch | 6/3/2008 |
Q: I have a 96 Wide Glide, and the starter clutch has gone. What is the process in removing the ...
A: First, disconnect the battery, Then you are going to have to drain the primary oil, remove the ...
|
| removing magneto | 6/3/2008 |
Q: 69 sportster, Magneto, Compression stroke rear piston at top. Points have already opened. Mag is ...
A: Your gap for the spark plugs should be .020 with a mag. To remove the mag it should, after you ...
|
| RE:First start of the year | 6/2/2008 |
Q: I took my '92 Soft tail out of my storage shed and went to start it for the first time after winter ...
A: Your bottom end of the bike was full of oil. Over the winter oil weeped into the bottom end and when ...
|
| tapping noise on my 95 flhr | 6/2/2008 |
Q: i have changed the lifters and push rods and i still hear a slight tapping noise. what will still ...
A: If you want to get rid of the noise you are going to have to go with different lifters. The Harley ...
|
| oil leak | 6/1/2008 |
Q: I have a 75 harley shovelhead sportster. I have an oil leak that I can not locate. Also it seems ...
A: First, clean the motor really good and let it dry. Spray some deoderant that has baby powder in it ...
|
| 74 sportster tranny | 6/1/2008 |
Q: A friend recently purchased a 74 iron head that was making some noise in 3rd gear. So he took it to ...
A: It sounds like the trans needs to be removed and inspected. Noisy gears are a sign that a bearing is ...
|
| 1996 Ultra Speedometer Drive | 6/1/2008 |
Q: I own a 1996 Ultra. The speedometer drive is bad. The cable is not wanting to come off the old one. ...
A: There are two different ways they are installed into the drive unit. One, there is a small set screw ...
|
| 2006 HD 883C transmission | 6/1/2008 |
Q: My transmission does not go into 4th gear easily. I also hear grinding noises. How much to rebuild ...
A: It tough for me to give prices on here, since labor prices vary all over the country as well as ...
|
| Smoking Battery Cable when starting | 5/31/2008 |
Q: I have a 2002 Swift Custom with an S&S 113cu. When trying to start the bike, the motor will barely ...
A: They should have replaced them. What you are running into is you have to much compression for the ...
|
| electrical trouble | 5/31/2008 |
Q: I have a 1973 sportster. I replaced the selanoid last year. Bike will start on occasion but other ...
A: The popping you are hearing is probably a breaker. I would start by replacing it. If it still keeps ...
|
| 2004 heritage flstc | 5/31/2008 |
Q: I would like to replace stock front sliders with chrome,i have service manual,but not sure how much ...
A: You will have to jack the bike up and remove the front tire, fender, brake caliber. Once you have ...
|
| starter relay and solenoid wiring | 5/31/2008 |
Q: hey bro, i just had my top end rebuilt on a 1975 ironhead. i got it home, trailered it, and went to ...
A: You are going to have to get a wiring diagram and start tracing the wires out. If you are hookinig ...
|
| tapping noise on my 95 flhr | 5/30/2008 |
Q: i have changed the lifters and push rods and i still hear a slight tapping noise. what will still ...
A: All motors that lifters, like on harleys, do a little tapping. Its the valve lash in the pushrod and ...
|
| VIN# Location / 1983 FLHT Harley Shovelhead | 5/30/2008 |
Q: I've inherited the above bike and I want to sell, but I cannot find the VIN# to obtain a duplicate ...
A: Look around the neck, where the forks connect to the frame, and there should be a vin number. It ...
|
| Knocking | 5/30/2008 |
Q: While replacing base and head gaskets on my 97 bagger, i had the cylinders honed and put in new ...
A: Since you just changed the rings and did some honing, you might have to much clearence in the ...
|
| Foork Seals | 5/27/2008 |
Q: I have a 91 fatboy and the fork seals are leaking I do all of my own work but I have never changed ...
A: You can replace the studs. they screw in. To replace the seals you need to remove the front wheel, ...
|
| 2006 Sportster XL883C Questions | 5/27/2008 |
Q: I have a 2006 Harley Davidson Sportster XL883C. While on a ride yesterday, the battery cover panel ...
A: the only place you can get the clips you are refering to is a dealership. As to the check engine ...
|
| Sleeping FXR | 5/27/2008 |
Q: I have a 93 FXR and it sit a lot for the past years or so as to some medical issues with me. I ...
A: You have a short in one of the systems. I would start by removing components from the different ...
|
| 84 Harley clutch problem | 5/26/2008 |
Q: Found your site AFTER I made my mistakes. Bike was not releasing clutch, so I adjusted (what I ...
A: The cable should be counterclockwise. Put it back together and put the cover on with alot of slack ...
|
| Shovelhead | 5/26/2008 |
Q: I have a 1983 FXRS Shovelhead and finding parts is hard, can you suggest a web site that has parts ...
A: Go to V-twin manufacturing web site. You can look at their catalog. They have all the parts you need ...
|
| oil pump | 5/25/2008 |
Q: hi mike i ask U last year about my 97 dyna glide smoking a little when first started up and u were ...
A: That is somthing new to me too. I have never seen the teeth gone on oil pump gears. They are ...
|
| shifting | 5/25/2008 |
Q: i have a 74 sportster, trying to put it in nuetral is becoming a pain, then when i think i have it ...
A: Your problem is the shifter cam is probably worn and needs replaced. It wouldnt be the fluid. In ...
|
| battery removal | 5/24/2008 |
Q: How do you remove the battery of a 2000 low rider HD?
A: remove the seat. Looking at the front left side of the battery box you will see 2 bolts. Loosen ...
|
| no start | 5/24/2008 |
Q: I just bought a '87 sportster. It was upgraded from 883 evo to 1200 and belt drive, S&S carb, lots ...
A: First make sure your ground wire is good. bad ground and the starter will heat up. If the battery is ...
|
| 2000 FXDWG | 5/23/2008 |
Q: I have a 2000 HD FXDWG which has a strange but almost unnoticeable sound in the front end. It sounds ...
A: Jack the bike up so the front wheel is off the ground and spin it. You are probably hearing a disk ...
|
| Proper spark plug selection | 5/23/2008 |
Q: I am looking to replace plugs in my mototr, and we all know how the whole cross-referencing thing ...
A: Spark plugs, like alot of other things, are personnal preference. Ask a 100 people which plug is the ...
|
| pushrods | 5/23/2008 |
Q: How do I adjust the pushrods on an 86 FLH? these are stock rods on this bike. ANSWER: If you have ...
A: Even the bike you are refering to has solid pushrods. If you have adjustable pushrods then they have ...
|
| 1983 fxe shovel | 5/23/2008 |
Q: hey mike i have a problem i put a new voltage regulator on my bike but when i went to test it it was ...
A: You need to check your regulator at the battery. With a volt meter you should be getting around 13.5 ...
|
| sportster 2004 starter replacement | 5/23/2008 |
Q: How easy is it to replace the starter on a 2004 Sportster? I have a lot of mechanical experience ...
A: Pull the primary cover and bump the starter button to see if it engages the gear on the clutch. The ...
|
| dyna mid controls | 5/22/2008 |
Q: Just got an 05 FXDC for the wife. She wants the forward controls removed and put back to mids. I'm ...
A: Stick with 05 parts. I dont have anything that would tell what years will fit for midcontrols, so I ...
|
| '01 FLHT front end | 5/22/2008 |
Q: Where can I find the proper measurements for the triple trees? ANSWER: I am a little confused on ...
A: I am not sure what that measurement is. You would have to check with a harley dealer on that. They ...
|
| noise when hit bumps | 5/22/2008 |
Q: I recently started hearing a 'chirping' noise when I hit bumps on my 2005 1200C HD that has a Lehman ...
A: I would first check the front end to make sure everything is tight. Check your brake pads in the ...
|
| battery problem | 5/22/2008 |
Q: Mike I have a 1985 flht ex police bike I bought 2yrs ago I put a new sears battery in it had no ...
A: First, I would start by having the battery tested to make sure it good. Even though you have 12.5 ...
|
| FXR | 5/21/2008 |
Q: Mike, I have a 1985 FXR with a 1999 S&S 113 motor, their is no way to get the bike into neutral ...
A: the shifter drum is located inside the trans, so you would have to pull the trans out. If you plan ...
|
| FXR | 5/21/2008 |
Q: Mike, I have a 1985 FXR with a 1999 S&S 113 motor, their is no way to get the bike into neutral ...
A: Harleys have always been tough to find netural, due to the fact that there is a small space on the ...
|
| 1984 FLHTC Evo clutch adjust | 5/20/2008 |
Q: My bike always wants to go, VERY hard to find neutral while stopped at a light. Do you think a ...
A: If your bike is pulling you foward at a light, tehn your clutch needs adjusted. Go to the cable and ...
|
| 1980 FLT TOURGLIDE PRIMARY | 5/20/2008 |
Q: I replaced primary chain,dampners,sprockets,clutch hub and housing 2yrs ago,everything was good now ...
A: If your chain is only two year old, it is not likely it bad. Go for a ride and when the bike starts ...
|
| smokin | 5/20/2008 |
Q: i have an 87 FL with 63K on the odometer; my brother (now passed on) bought this bike after it was ...
A: First, it would be very expensive to convert to fuel injection from a carberated bike. I dont think ...
|
| motorcycle electrical problem. | 5/19/2008 |
Q: i tried to start my bike all i got was a few cranks of the starter after that there was no juice no ...
A: If your starter is turning on its on when you hook up the battery, then either the starter button is ...
|
| 1999 Softail evo hard to start | 5/19/2008 |
Q: I recently replaced all of the gaskets from the head covers down to the tappet guide because there ...
A: First, make sure you bleed the lifters before adjusting them. It sounds like the bike is fuel ...
|
| ghanging fluids | 5/17/2008 |
Q: i have a 1994 ultra classic,i pulled plug in pan at front to drain oil from motor.pulled out allen ...
A: The drain for the trans is on the bottom of the trans, close to the center of it. The primary has ...
|
| 1974 shovehead conversion | 5/16/2008 |
Q: I have a great running 1974 shovelhead...of course it drips on the garage floor. My question is, ...
A: Yes, you can convert it to the bigger front end, but I would go with a FLH shovel front end. Easier ...
|
| 2006 Fatboy clutch issue | 5/16/2008 |
Q: I was on a bit of a road trip yesterday and stopped by the dealer where I bought my bike, about 100 ...
A: What you are going to have to do is pull the primary cover and inspect the clutch basket. Your ...
|
| sporster harley 1999 | 5/16/2008 |
Q: i have a 1999 harley sporster.it is using oil not smoking or leaking. it has 25,000 miles on it.it ...
A: Generally, if your petcock leaks through you dont get fuel in the oil, but it can happen. But, in ...
|
| Oil and gas coming from vent line. | 5/15/2008 |
Q: I just bought a 1991 FXSTC that had sat in a garage for about 6 weeks with the gas on. Now when I ...
A: the oil tank sits higher than the motor. What happens is oil is weeping past a ball in the oil pump ...
|
| 08 dyna fat bob | 5/14/2008 |
Q: I would like to drill a few holes in my exhaust just to have a bit more noise...how would this ...
A: I dont recommend drilling holes in the exhaust. First, depending on the number of holes and size, it ...
|
| installation of baffels | 5/14/2008 |
Q: im running 40 inch by 1 3/4 inch XLR drag pipes shes making great h.p. & torque...im thinking about ...
A: Installing baffles will not affect the starting of your bike. Most baffles are installed by drilling ...
|
| winter storage | 5/14/2008 |
Q: With riding season upon us and winter a while off, I was wondering how to prepare to store my 1972 ...
A: When you are done riding, change your fluids. Fill the gas tank to the top. Start and run the bike ...
|
| vance & Hines Straightshots slip on | 5/13/2008 |
Q: I'm getting a popping sound on deceleration after installing the V&H Straightshots slip on's. I was ...
A: Your popping is probably from a lean condition as well as no back pressure on the exhaust system. ...
|
| Blue Smoke, 1998 Sportster | 5/13/2008 |
Q: We just purchased (via Ebay)and are leaving tomorrow morning to pickup a 1998 Sportster 883, 5600 ...
A: Its hard for me to say what the price would be. Labor prices are different all over the country as ...
|
| loses power during deceleration | 5/13/2008 |
Q: I have a 1997 road king with EFI. When I decelerate, the ignition seems to shut down until the ...
A: If the motor doesnt die then the bike is not losing power, it has just cut back on fuel, dince you ...
|
| primary oil change | 5/12/2008 |
Q: how much oil do i put in the primary for an 85 sportster ironhead
A: Looking at the bottom of the primary cover, close to the center, you will see a screw. remove it. ...
|
| Changing gas tanks and ignition switch | 5/12/2008 |
Q: I've got a 92 FXSTS and I want to change the tank to a sporster tank. I was wondering if you had any ...
A: If you change to a sportster tank you will have to fabricate some mounts for it. You would have to ...
|
| sporster harley 1999 | 5/11/2008 |
Q: i have a 1999 harley sporster.it is using oil not smoking or leaking. it has 25,000 miles on it.it ...
A: You can burn oil without smoking if your rings are starting to go bad. You would either have to do a ...
|
| 1200 Custom 1999 | 5/11/2008 |
Q: When starting up I only get the clicking sound from the transmission area. Bought the bike in -99 ...
A: First, I would have the battery tested or just replace it. A battery sitting for that long is ...
|
| rake degree for triple tree | 5/11/2008 |
Q: try to give as much info..1978 harley sportster 1000 xl..tubes 39 inch..approx 26 inches from axle ...
A: What you need to do it first block bike so it will sit level without the front tire and the frame is ...
|
| Transmission leak | 5/11/2008 |
Q: I just replaced all the gaskets and seals on my 93Wideglide. Almost instantly the trany started to ...
A: James gaskets are all I use in in my shop. If your bike is leaking on the kickstand then it either ...
|
| Backfire / Low Power | 5/10/2008 |
Q: I just bought a 1991 FLSTN last night. 3500 mi on Factory Reman Engine(stock V2). Screaming Eagle ...
A: Your air/fuel mixture screw is closed to much. Should be around 1 1/2 turns. Change your ...
|
| timming | 5/10/2008 |
Q: i have a 1991 883 xl sporster i want to check the timing i see the marks on the plate but none on ...
A: There is a timing plug on the left side of the case. You have to remove the plug and install a clear ...
|
| 2004 Dyna factory mixture screw setting | 5/10/2008 |
Q: Mike-Put on V & H Shortshots, cut baffle. Upped high speed jet & low. Ran fine, but played with ...
A: Its not your air/fuel misture screw that is the problem. the air/fuel mixture screw only affects the ...
|
| Backfire / Low Power | 5/10/2008 |
Q: I just bought a 1991 FLSTN last night. 3500 mi on Factory Reman Engine(stock V2). Screaming Eagle ...
A: Pull your spark plugs and let me know what color they are. Are you running a stock carb? Dont add ...
|
| 1972 Sportster | 5/10/2008 |
Q: I've had my 72 Sportster in storage for the winter, I pulled it out, cleaned it up and went to ...
A: Inside your oil pump there is a small ball and spring. the ball is suppose to keep the oil from ...
|
| oil leak from air cleaner? | 5/10/2008 |
Q: I recently tipped over my 99 fxstc while turned off to use an ATM machine. BUMMER! I caught it and ...
A: First, you need to find out where the oil is coming from. Clean the bike really good and let it dry. ...
|
| charging problems | 5/9/2008 |
Q: ive chage sator and rotor,volt meter , battery, now my charing system isnt charging again whats ...
A: Sounds like the stator you installed was bad. I use accel stators and dont have any problems with ...
|
| front wheel alignment | 5/9/2008 |
Q: but if the rear wheel is in the center of the frame and the forks are center of the frame, how can ...
A: What the book is refering to is the fact that the front tire is not as wide as the rear. So what ...
|
| 76 sportster | 5/9/2008 |
Q: got a stock ironhead that i want to convert to electronic ignition. when it comes to electric ...
A: The difference between single fire and duel fire is, the duel fire fires the spark plugs on the ...
|
| hd cases | 5/8/2008 |
Q: i have a 1985 sportster the left side bearing housing (the steel insert)came lose can it be repaid
A: Your better off getting a new set of cases. You would have to get a machinest to make the repair by ...
|
| How much noise? | 5/8/2008 |
Q: I recently purchased a used 1993 Fat Boy w/13,000 mi. The dealer I bought it from gave me a 6000 mi ...
A: All lifters make some noise. Because harley lifters are on the outside of the motor you hear it ...
|
| starting trouble | 5/8/2008 |
Q: My HD FLH 1972 1200 cc is about to get me mad !! :) It wont start. When i push the button it keps ...
A: First, I would test the battery. You might have a bad cell. Check both battery cables. the starter ...
|
| 76 sportster | 5/8/2008 |
Q: got a stock ironhead that i want to convert to electronic ignition. when it comes to electric ...
A: There are many different electronic ignitions out there and if you ask a 100 people which one is the ...
|
| 1974 XLCH | 5/7/2008 |
Q: I Just Put a elec start on my XLCH and the selunoid will engage but the starter motor wont spin.My ...
A: If your bike way totally kickstart before, you have to change out the battery box and go to the ...
|
| ignition switch | 5/7/2008 |
Q: Hey Mike I have a 1998 sportster and im redoing the ignition from a key to a barrel key but im not ...
A: There is no ground on a ignition switch. You have a hot wire, a lights wire and a acc. wire. ...
|
| starter | 5/7/2008 |
Q: need to know just how to remove a starter off of a 71 sportster 900 ....thanks...like do i have to ...
A: Remove the battery and the wire going to the starter. Remove the two bolts holding the starter in ...
|
| Codes for 2003 Road King | 5/6/2008 |
Q: Mike, Can you recommend a particular scanner for which I can obtain my engine codes when I get a ...
A: Most of the scanners are expensive and the one from harley can only be purchased by a dealer. the ...
|
| crane hi 4 and low oil pressure | 5/6/2008 |
Q: this is killin me. installed crane hi 4 single fire. got tdc, cant see timing mark(35 deg) through ...
A: If the oil light doesnt come on, you might not be losing oil pressure. try another gage. On the ...
|
| engine noise | 5/6/2008 |
Q: Have a '97 FLHR with 70,000. Have it torn down to cases now replacing gaskets. Found some scoring ...
A: With 70,000 miles and you have it part way down, I would go ahead and inspect the rod bearings, just ...
|
| Battery | 5/6/2008 |
Q: How do I reach the battery on my 2004 dyna wide glide. What are the steps in replacing it. Thanks ...
A: Remove hte battery cover on the side. there are two bolts at the bottom of the battery box. Loosen ...
|
| Stator | 5/6/2008 |
Q: How hard is it to install a new stator.. Battery will not stay charged so I am assuming that this is ...
A: First you need to do a OHMs test and a AC voltage test ont he stator to make sure it bad and not the ...
|
| How to change REAR BELT FINAL DRIVE | 5/5/2008 |
Q: I need to now how change the rear belt drive for a softail 99
A: What you are going ot have to do is remove the primary, clutch, motor sprocket, jackshaft, starter, ...
|
| starter solenoid | 5/5/2008 |
Q: Just how does the starter solenoid work? I push the starter button, starter dog engages, but ...
A: A solenoid is nothing but a magnet. When you hit the starter button it sends 12 volts to a post on ...
|
| rear cyclinder very lean | 5/5/2008 |
Q: I'am a small harley repair shop, and also a mobile dyno tuner. A customer bought me bike after ...
A: Since the bike only runs on one carb and the fuel is split between two cylinders and you have only ...
|
| 2005 Road King | 5/4/2008 |
Q: I put a new clutch cable on my bike. Now when I put it in gear and let the clutch out the bike does ...
A: It sounds to me like the clutch is to tight. Make sure the finger for the rod on the right side of ...
|
| 1984 sporty ironhead | 5/3/2008 |
Q: i just bought a 1984 ironhead sporty, the previous owner claims that the motor was rebuilt, but he ...
A: Do your compression test with a hot motor. Also, do a bleeddown test. I am not familar with the ...
|
| 1984 sporty ironhead | 5/3/2008 |
Q: i just bought a 1984 ironhead sporty, the previous owner claims that the motor was rebuilt, but he ...
A: Once a ironhead is rebuilt, you really shouldnt have a problem tuning it. When you did the ...
|
| 1991 FXSTC performance | 5/3/2008 |
Q: I installed a Super E carb a number of years ago. The bike ran fine for awhile but then developed a ...
A: Since you said it ran fine and then started running bad, I would look other places. Once you have ...
|
| rear brake pad replacement | 5/2/2008 |
Q: I have a 2005 HD Sportster 1200C. I need to replace the rear pads. What kind do you recommend and ...
A: using a certain pad is a matter of opinion, but if it were me I would go with a kevlar type pad. ...
|
| Vance & Hines Straightshot Slipons | 5/2/2008 |
Q: I am installing a set of Vance & Hines Straightshot Slipons on my 2001 Harley Dyna Superglide FXD at ...
A: If you change to a highflow pipes you make the bike run a little leaner. Adding a highflow air ...
|
| 87 flhtc clutch /cable adjustment | 5/1/2008 |
Q: I installed a new clutch cable and clutch lever has alot of play and is not springing back out. I ...
A: Loosen the cable alot. With the bike sitting upright remove the derby cover. Under it you will see ...
|
| Knocking and Bogging | 4/29/2008 |
Q: 2002 FLHR-I Roadking 88CI Stage 1 upgrade 1.) I have a loud knocking at higher rpm's. Sounds like ...
A: The plugs should be a tan in color, so you are not running lean. The knocking can be several things, ...
|
| 2001 nighttrain | 4/29/2008 |
Q: Mike my question is about fluid quantities and levels. My bike is a 2001 harley davidson nighttrain ...
A: Check your motor oil sitting on the sidestand, not upright. Check the primary and the trans sitting ...
|
| clutch | 4/29/2008 |
Q: how do i make the clutch ajustment on my 2005 harley electra glide its a 1450
A: With the bike sitting upright, remove the derby cover. Go to the clutch cable and adjust it so there ...
|
| 1984 HD Sportster rear lights | 4/28/2008 |
Q: The tail light and L and R blinkers are not working on my bike. I cannot find a fuse box to check... ...
A: You donthave fuses, you have breakers. They are located under the seat. Follow the wire coming from ...
|
| oil change | 4/28/2008 |
Q: I have a 85 sportster but my friends say the motor looks like a shovel head, I am tring to change ...
A: The 85 sportster is a shovelhead. there is not drain for the bottom end of the case, just drain the ...
|
| 2004 Sportster rear brakes | 4/27/2008 |
Q: Just replaced pads and master cylinder and can't get the system to bleed out doing everything right ...
A: Because the the small diameter of the hole for the brake fluid to go through in the master cylinder ...
|
| motor mounts | 4/27/2008 |
Q: My 98 WG vibrates excessively when i have someone on the back. I had the engine and transmission ...
A: I dont have any books to send. You best bet is to buy a service manual from a harley dealer. Do one ...
|
| 1977 sportster | 4/27/2008 |
Q: I have a 1977 sportster with no 4th gear, was riding and went to up shift no noise just will not go ...
A: Anyone who deals with V-twin Manufacturing can get you a service manual. About the only thing you ...
|
| ignition | 4/27/2008 |
Q: I replaced stock ignition Mod with a screamin eagle on my 01/fxd now I,m getting a engine light. all ...
A: You might have gotten a bad modual, but i doubt if the dealership will take it back. What you are ...
|
| 2002 Super Glide charging issue | 4/26/2008 |
Q: Mike, I have a charging issue with my '02 Super Glide with the following symptoms: I've installed a ...
A: What might be happening is the covering on the wires of the stator has come off. As you ride the ...
|
| transmission leak | 4/26/2008 |
Q: My 2000 harley softail trans has a slight leak.I think it's coming from the shift lever where it ...
A: In order to replace that seal you will have to remove the inner primary. Without taking out the ...
|
| 2002 Super Glide carging issue | 4/26/2008 |
Q: Mike, I have a charging issue with my '02 Super Glide with the following symptoms: I've installed a ...
A: Your stator sounds fine. the best you are going to get at the battery is about 13.5 volts. I am not ...
|
| Leaky crankcase | 4/26/2008 |
Q: Bought a 93 XLH Sporty two years back. Was in love whilst I rode it for the first 2 months. I then ...
A: If you havent started it yet, then there should be no leak. They base gasket only leaks when you are ...
|
| 1980 shovel kick only | 4/26/2008 |
Q: i went to start my bike this year and as i kick it over it is gurgling out of the breather hose ...
A: What has happened ove the winter is oil has weeped into the bottom end of the case. When you start ...
|
| Primary/Transmission Oil Change issues on 2005 Sportster XLH1200 | 4/25/2008 |
Q: I recently tried to replace my derby cover on a 2005 Sportster XLH1200. When I took the old one off ...
A: First, the primary only holds 32 ozs so you need to drain it and replace it. Next, remove the derbly ...
|
| electrical problem | 4/23/2008 |
Q: I have a 1986 flhtc. My bike has started to shut down at random times and places, (more often in ...
A: It sounds like you have a short in your lighting system. I would look for the short. If you change ...
|
| Not Starting after winter! | 4/23/2008 |
Q: 1987 Harley Electra Glide FLHTC 1340 EVO Only had bike 1 Year. ...
A: My shop is located in Mount Victory Ohio, which is close to columbus. Pull your plugs and make sure ...
|
| oil | 4/23/2008 |
Q: I have a 2007 road king. I need to know where the primary oil drain is and how to refill. I also ...
A: Primary drains from the left side, at the back of the primary cover at the bottom. You will see a ...
|
| harley won't start | 4/22/2008 |
Q: I have a 2006 harley 883 sportster. It ran fine up until a couple of weeks ago it started ...
A: Yes, you can charge the battery in the bike and use the frame for ground. It sounds like you fouled ...
|
| 86 sportster engine/tranny noise | 4/22/2008 |
Q: i have a 86 1100 sportster and when it is running it sounds like there is a rock rattling around ...
A: Its have for me to tell about noises on here, due to the fact I cant hear them. What you need to do ...
|
| FLHTC BUMPERS | 4/22/2008 |
Q: WANNA REMOVE THE BUMPERS. HOW MUCH INVOLVED? I AM MECHINICALLY INCLINED. DO I NEED TO LIFT THE BIKE? ...
A: If youa re wanting just to remove the rubber, they are attached on the inside of the fenders. If you ...
|
| 98 Road King cuts out spontaneously | 4/22/2008 |
Q: My 98 Roadking has this problem where I'm riding in top gear, say at 100ks, or even third, ...
A: Its probably either your bank angle senser or your cam position senser. the problem is you have to ...
|
| Charging system | 4/21/2008 |
Q: If it doesn't cost me anything for an answer, I'd like to ask about my 1995 Harley Davidson FLHT. ...
A: First, check the voltage at the battery witht he bike running. At 2000 RPM you should show around ...
|
| Removal of tanks and dashboard on 1973 FLH | 4/21/2008 |
Q: I need to remove the tanks and dashboard on my 1973 HD FLH - the service manual I have does not give ...
A: Remove the center bolt which holds the chrome cover on. If you have a choke knob there, remove the ...
|
| no fuel to carb...starting | 4/20/2008 |
Q: I have an 03 Sportster 1200. Riding home it started loosing power..stalled once. I got it home, ...
A: You have a vaccumn hose connected to the petcock. Make sure its attached and not pinched. You can ...
|
| No Speedometer | 4/20/2008 |
Q: I have a 2002 hd Roadking.The speedometer stoped working it has 15000 miles.Now the directions wont ...
A: Your best bet, since your check engine light is coming on, is to get a dianostic run on the bike. ...
|
| 99 EVO rocker box leak | 4/20/2008 |
Q: I have a 1999 evo 1340 on a FXR 2 frame with a leaking rocker box gasket on the rear cyl. I am just ...
A: I am about 3 hours from Cleveland and yes I still repair harleys To replace your rocker boxes you ...
|
| not charging my battery | 4/19/2008 |
Q: i have an old 1200 shovel head early 80's seem like it is only pulling from the battery and not ...
A: You need to teat the stator first. Do a OHMs test at both pins of the stator. Then start the bike ...
|
| S&S carb issue | 4/18/2008 |
Q: I have a 77 FXE shovelhead, I just recently had the top end re-done because of oil seeping past the ...
A: Correct jetting will make it idle slightly higher, but changing the jets will not help. Lean running ...
|
| screaming eagle on 07 heritage | 4/18/2008 |
Q: Mike I installed the screaming eagle on my bike but the sound is a little louder then the originals. ...
A: You can remove the baffles, but what you are doing is just changing your exhaust into drag pipes. ...
|
| S&S carb issue | 4/18/2008 |
Q: I have a 77 FXE shovelhead, I just recently had the top end re-done because of oil seeping past the ...
A: When having a top end done you might get black plugs due to the fact the rings are not seated yet ...
|
| Evo oil pump gear shaft | 4/18/2008 |
Q: I sheared a key in the drive gear and my manual says the shaft can be removed with engine and trans ...
A: You never said what year or model you have, but generally the pump and shaft have to come out ...
|
| white milky oil coming down thru my oil level when running the bike . | 4/18/2008 |
Q: I changed the spark plugs by my self for my motorcycle and i beleive i did a good job of keep ...
A: All motors draw some moisture when you park them. As the motor cools down it draws air. After you ...
|
| 94 XLD Base Gasket Issues | 4/18/2008 |
Q: I recently did a base up rebuild. Replaced the rings, all seals and gaskets. After I got everything ...
A: You can only torque the heads bolts to the specs. Once they are set you cant retorque then. If you ...
|
| 1999 XL 1200S | 4/17/2008 |
Q: I cannot belive i ve done this, ignition cable routing i did not mark specifics. can you lend a ...
A: looking from the top of the bike, like you sitting on it, the front plug end on the coil on the ...
|
| oil leak | 4/17/2008 |
Q: i have an oil leak from the breather,also no start after winter storage. there is no oil in the ...
A: there is a ball int he oil pump that is suppose to keep the oil from funning into the motor when its ...
|
| Lean plugs and popping, but only lately | 4/17/2008 |
Q: Need to address a problem with my bike and I'd rather do it myself, local dealer shop just threw gas ...
A: I am located in Mount Victory, Ohio, which is about 50 miles from Columbus. As to your problem, I ...
|
| Horn and tail lights do not work | 4/16/2008 |
Q: I have 2000 fatboy and the horn and tail lights do not work. No running lights or brake lights. I ...
A: If you have power going to each conponent, but they dont work then you have a bad ground. Make sure ...
|
| mileage on a Harley Davidson | 4/16/2008 |
Q: My husband and I are looking into buying our first Harley and are pretty clueless about everything. ...
A: That is not a bad deal on the bike if it is good condition. 15,000 miles is not alot on a bike. One ...
|
| brake light | 4/15/2008 |
Q: 2004 Electra glide brake light stays on all the time what is the most likely cause
A: Check your front brake handle. If you look at the switches and the brake lever you will see that ...
|
| 1916 harley- fully restored | 4/15/2008 |
Q: My brother in law has a 1916 Harley that has been fully restored. We are interested in buying it ...
A: Alot depends on the restoration. If all the parts are orgional it will be worth more. You never said ...
|
| Engine noise? | 4/14/2008 |
Q: I have a 96 Road King and I am getting a whistling noise out of the alternator, crank shaft area ...
A: About the only thing that wouls whine on that side of the bike would be the belt or the gears in the ...
|
| HD Starter | 4/14/2008 |
Q: Starter on my 01 HD low rider makes a hell of a noise.Will start to engage then it makes a grinding ...
A: Your going to have to pull the starter. Its either the starter clutch or a bearing is going out. You ...
|
| 2001 FLH Standard | 4/13/2008 |
Q: I just tried to jump my battery with my truck because I did not have enough cranking power left in ...
A: First, dont jump start your bike with a auto or truck. To many cranking amps. Get a battery ...
|
| lost | 4/13/2008 |
Q: 1980 xlh sprotster - Bike ran normal for about 30min and started idling bad. Accidently turned air ...
A: You probably fouled a plug. Make sure the plugs are clean. Start the bike and once it warms up turn ...
|
| 1984 FXRS Neutral hard to find | 4/2/2008 |
Q: I was wondering what I could do to find neutral on my bike. I just bought it and can never seem to ...
A: Finding netural on some harleys has always been hard. I have a 1998 that is a bear to find netural. ...
|
| 2000 harley 883 speedo cuts out | 4/2/2008 |
Q: the speedo will work and then cut out until it is restarted. it also idle and stay running at low ...
A: What you need to do is test the ignition system. It sounds like the pickup is cutting in and out, ...
|
| Vance & Hines short shots | 4/1/2008 |
Q: I thank you if you could answer this for me, I have a 1998 Harley Softail Custom I put Shot shot ...
A: I am not sure if those baffles are bolted in or welded in. Look on the back of the pipe. If you see ...
|
| 2002 FLSTSI rear cylinder dry fouling plug | 4/1/2008 |
Q: I have roughly 150 PSI on a dry compression test with this twin cam...the rear cylinder is dry ...
A: You stated that you were losing oil, but no leaks. In order to lose oil, it either has to leak or ...
|
| 2002 FLSTSI rear cylinder dry fouling plug | 4/1/2008 |
Q: I have roughly 150 PSI on a dry compression test with this twin cam...the rear cylinder is dry ...
A: You have to remove the heads to remove the keepers, due to the fadt that you have to compress the ...
|
| fork leak around dust boot | 3/31/2008 |
Q: 1989 FXSTC that's developed a leak around the dust boot. Boots have chrome caps that seem to be ...
A: To take the lower leg off you have to remove the allen head bolt in the bottom of the lower then it ...
|
| !981 sturgis | 3/31/2008 |
Q: I own a 1981 sturgis and i have a 4 speed stock transmission on it and it keeps on locking up on me ...
A: If you are locking up in two gears, then you are having a spacing problem with the gears. the trans ...
|
| oil leak | 3/31/2008 |
Q: she's a 1990 FLHS, I rode /07 with no problems at all. A couple of oil drips every couple of days. ...
A: The location you are talking about is probably the vent. Over time, since your oil tank is sitting ...
|
| carb and back brakes | 3/31/2008 |
Q: I have a 1995 FXRS Low Glide. I'm looking for a good used stock carb for her. Also having problems ...
A: On your brakes, your probably not bleeding them long enough to get the fluid to the brake caliber. ...
|
| idle setting 1999 Elctro Glide Classic | 3/30/2008 |
Q: I have a 1999 Electro Glide fuel injected Harley & I think The idle is set too high. How do I adjust ...
A: It should be set at 900-1000 RPM. To set it remove the air cleaner and on the back plate you will ...
|
| 1991 XLH1200 Shifter | 3/30/2008 |
Q: Mike - This bike only has 25K miles on it. Out riding twisties when I downshifted and the lever ...
A: Sounds like you have a broken shifter spring. It is located in the trans. To get to it the trans ...
|
| fork leak around dust boot | 3/30/2008 |
Q: 1989 FXSTC that's developed a leak around the dust boot. Boots have chrome caps that seem to be ...
A: The chrome caps might be glued to the rubber ones, so you might tear them up trying to remove them, ...
|
| 1977 Harley Sportser | 3/29/2008 |
Q: I change the primary cover put everything back correctly. The bike was riding fine before I changed ...
A: Sounds like you have a trans problem, which would be unrelated to changing the primary. Your going ...
|
| handlebar grips | 3/29/2008 |
Q: what is the best way to replace handlebar grips on dyna glide
A: on the right side you have to remove the cover for the throttle. Inder it you will see the cables ...
|
| 2000 Electraglide front brake bleed | 3/28/2008 |
Q: My front brake lever just about bottoms out, believe I need to bleed front brake as pads look good, ...
A: Remove the lid on the master cylinder and make sure it full. Go to the first caliber and on top of ...
|
| 89 ulta glide clutch | 3/27/2008 |
Q: we got it and the sanp ring problem fixed. Now the clutch wants to slip in 4th and 5th gear with ...
A: With the bike sitting upright, loosen the cable so it has some slack in it.. remove the derby cover ...
|
| shovel will not stay running | 3/26/2008 |
Q: Hey MR Wells...1975 shovel. one day I was riding down the road and the bike just died. let it sit ...
A: The positive side of the coil, where the two 12 wires attach, you should show around3 OHMs. On the ...
|
| shovel will not stay running | 3/25/2008 |
Q: Hey MR Wells...1975 shovel. one day I was riding down the road and the bike just died. let it sit ...
A: I would start by doing a OHms test on the coil to make sure its good. Do it when its cold and then ...
|
| Hard starting | 3/25/2008 |
Q: I have a custom chopper, 124 S&S, BDL open belt drive with outer bearing supports, baker 6 speed ...
A: If you have compression releases, then you are not fighting much compression when trying to start. I ...
|
| Making trunk lights on Ultra run-turn-brake | 3/25/2008 |
Q: How do you rewire the trunk lights on a ultra to be run-turn-brake. I saw one last week on the ...
A: That is somthing that is added on, probably aftermarket. In order the make a light a run and brake ...
|
| engine upgrades | 3/24/2008 |
Q: I'm ready to button up my 98 FXD motor with a set of 10.5 Wesco Pistons, Screamin Eagle Heads (w/ ...
A: You are probably fine, but if you want to check you put some clay on the piston and install the ...
|
| engine knocking | 3/24/2008 |
Q: i have an 81 superglide it has been rebuilt a while back . i can hear a knock in the middle of the ...
A: Start will just unbolt from the inner primary and slide out under the oil tank. As to the time for a ...
|
| headlamp install on 2000 fxstd | 3/23/2008 |
Q: bought after market headlamp for my duece. It came with only two wires leading from the lamp. my ...
A: Check the buld and make sure its a two filiments. If it does you need to figure out which one is the ...
|
| 89 ultra classic starer hangs | 3/23/2008 |
Q: on our '89 ultra classic we installed a new starter and battery and it will not start without ...
A: I would first check to see where the snap ring came from. You have one holding the bearing in the ...
|
| 1999 sproster oil | 3/23/2008 |
Q: how do you change the oil? where is the drain plug, or do you just drain the tank and change the ...
A: There is a drain hose on the underside of the oil tank, so you need to locate it. It is either ...
|
| not enough juice? | 3/22/2008 |
Q: i just had a 131ci H&L motor put in my bigdog chopper,i have 12:1 compression w/releases. I am on my ...
A: First, test the battery. Even though its new it might have a bad cell in it. Next, check your ...
|
| carburator jeting | 3/21/2008 |
Q: Hey Mike,got a question about jeting a carb on a 2006 fxsts.I bought this springer the other day and ...
A: Get yourself a Dyno-jet kit. In it there will be the correct jets and some other parts you need. You ...
|
| aftermarket brake light | 3/21/2008 |
Q: I put an aftermarket "cat's eye" tail light on my 99 sportster. It has a black and red wire, which ...
A: Alot of the aftermarket companies use different color wires, so its would be hard for me to tell you ...
|
| hard start | 3/20/2008 |
Q: I HAVE A 75 SPORTSTER THAT STARTS HARD IN COLD TEMPERATURE ITS IN THE 40S. I USE 60 WEIGHT OIL AFTER ...
A: Even though you say the battery is new, it might still be weak, so I would have it tested. Your test ...
|
| hard start | 3/19/2008 |
Q: I HAVE A 75 SPORTSTER THAT STARTS HARD IN COLD TEMPERATURE ITS IN THE 40S. I USE 60 WEIGHT OIL AFTER ...
A: Make sure you give it a couple shots of fuel with the throttle if you have a pumper on the carb. It ...
|
| 1993 ultra classic | 3/19/2008 |
Q: I have a '93 Ultra Classic w/ 25k miles that is running like crap. We moved here from Colorado a ...
A: Check your intake for a leak. You can start the bike and let it warm up. Spray a little carb cleaner ...
|
| carb problems | 3/18/2008 |
Q: I have a chop with a 2005 sportster 1200 motor in it.It is coughing,crackling and sputtering during ...
A: You have either a problem with the ignition or the carb. I would first do a OHMs test on the coil ...
|
| static timing | 3/18/2008 |
Q: I would be grateful if you can tell me how to do the static timing on a 1993 harley fxr,thanks ...
A: Remove the timing plug and locate top dead center. Go to the points and rotate the adjuster, just ...
|
| after market sissy bar for 93 sportster 883 | 3/18/2008 |
Q: Mike I bought an after market sissy bar for my 93 sportster 883 the holes all seem to line up but, ...
A: Most of the aftermarket sissy bars have a cutout so the bracket will fit without removing the ...
|
| lowering | 3/17/2008 |
Q: I have a 1990 fxst and want to lower the rear 1", do I need to preload the shocks or do anything ...
A: All you need to do is either find a lowering kit or replace the shocks. Make sure you have enough ...
|
| Changed my exhaust pipes | 3/17/2008 |
Q: I've a 2007 XL-1200C. I just put a set of Vance & Hines Short Shots staggered pipes on the bike, ...
A: Adding the pipes probably leaned out the motor, so you need to richen it back up. Riding it is going ...
|
| headlight housing wires | 3/17/2008 |
Q: i have a 76 xlch chop, you built the motor, and the frame was chopped and raked by D.H. near ...
A: The rear brake wire comes to the headlight housing for the front brake lever, so when you apply the ...
|
| 72 sporty | 3/17/2008 |
Q: i just got a xlch 72 sporty w/s&s super B not sure what size jet with new plugs and a shot of ethier ...
A: Your super B carb is fine for your bike. It might not be the carb, but the coil which is causing the ...
|
| sportser rockerbox leak | 3/17/2008 |
Q: i have a 1990 1200 sporty with 6000 miles on it.It has a oil leak between the head and lower rocker ...
A: Yes you can remove the lower rocker box without removing the pushrod tubes or the rocker arms. Just ...
|
| 83 flt 5speed | 3/14/2008 |
Q: I've replaced my clutch cable and need to know how to adjust it. No where near how my virago is. ...
A: With the clutch cable loose, go to the adjuster in the primary. Slowly turn the adjuster screw ...
|
| EVO oil seal | 3/13/2008 |
Q: main shaft oil seal is leaking. How can I remove it ? ultima 113 I see they have a tool to replace ...
A: To change the mainshaft oil seal you have to remove the primary cover, motor sprocket and clutch ...
|
| 1984 sportster xlx | 3/12/2008 |
Q: Mike, I just had my generator replaced as well as some of the wiring. I just barely got it home. It ...
A: You could have a bad plug wire, which would cause the problem. If the pushrods are to tight, you ...
|
| water in transmission | 3/12/2008 |
Q: my '97 wideglide had a cup of water in the transmission when i changed the fluid last. i dont ...
A: There are only a few places that water can enter. Top cover, side cover, dipstick, drain, vent or ...
|
| 1979 Sportster starting problem | 3/12/2008 |
Q: I just bought a 1979 Sportster. It runs great(no smoke). It had a starter problem. When you push the ...
A: All you have to connect is the positive on the meter, you can attach the other one to any ground. ...
|
| smoke | 3/12/2008 |
Q: i have a 1998 flsts ,a year ago i had it serviced and the said the o-rings replace on the valves ...
A: First, the valves dont have any o-rings so I am not sure what they replaced. The smoking means youa ...
|
| Clutch Problem | 3/10/2008 |
Q: Mike, I just purchased a 2004 Ultra Classic from my brother in law in Las Vegas. I work in the ...
A: You have a wet clutch, so it should be satarated. I would try to adjust the clutch. Loosed the ...
|
| 76 Ironhead Sporty blowing blow | 3/10/2008 |
Q: Mike, Just picked up a 76 Sporty Ironhead (project bike but running strong) from nephew. He got it ...
A: blowing blue smoke is an indication of burning some oil, but with only 300 miles on the motor the ...
|
| charging issue on 1994 Sportster | 3/10/2008 |
Q: I have a 1994 Sportster XLH 1200 with 7500 original miles on it. I drove it for several hundred ...
A: First, have the battery tested. You might have a bad cell in it. Once you know the battery is good ...
|
| speedometer failed 1996 fxdwg | 3/10/2008 |
| Q: My speedo and mile counter will not function,tur |
