You are here:
- Home
- Recreation/Outdoors
- Paintball
- Paintball
Paintball/Questions Answered by Expert Regis Jung
| Subject | Date Asked |
| Paintball HPA Tank | 6/29/2009 |
| Q: I just purchased a 72/3000 HPA tank for my Tippmann A-5. I dont wear a pod belt seeing as my armour ... A: hmmm, that's going to be personal preference right there. I would imagine the lower back, as it ... | |
| Macdev Droid Gladiator Regulator cleaning | 6/8/2009 |
| Q: I was wondering how to clean my macdevs regulator... and i dont want to break it so if you could ... A: http://macdevog.com/manuals/DroidManual.pdf Here's the PDF of the Droid, looks to be like an ... | |
| HPA | 5/23/2009 |
| Q: Ok so im getting the SP Ion and it comes with the tank but I was looking at a lighter tank because i ... A: Any tank will work. Be it high pressure output or low pressure output. you might want to get a HP ... | |
| Attaching Air Tank To Gun | 5/8/2009 |
| Q: Hey, Im new to paintball and i was wondering about attaching your air tank to your gun... Do you ... A: When screwing in your tank the general rule is to make sure you don't point downwards. If you point ... | |
| stuck bolt. | 5/1/2009 |
| Q: Hey when i put air pressure in my paintball marker (2004 NXT smartparts shocker) the bolt gets shot ... A: Sounds like it could be an oring filter problem or the solenoid got seized from a fluke over ... | |
| new paintball gun | 4/26/2009 |
| Q: im looking for a new paintball gun and only want to spend around $300. i really like the proto SLG ... A: The G3 is better in terms of reliability and speed. The SLG may have problems with the sear as it ... | |
| Angel Battery | 4/15/2009 |
| Q: I just got a 2001 Angel LCD from a friend which needs a new battery. Do you know where the battery ... A: The battery is located in the cylinder which is covered by the front cap and backplate. Looking at ... | |
| Proto rail and PMR | 4/15/2009 |
| Q: I was at exotic sports the other day and they had the proto rail for 274$ and beside it the pmr for ... A: The Proto Rail Matrix and SLG are 2 compltetly different guns in how they operate. The PMR uses ... | |
| Paintballs for DP G3 | 4/15/2009 |
| Q: What size paint balls are best for a Dangerous Power G3 with its stock barrel? A: Paintball has adopted the size .68 inch diameter as their size of projectile. Though paintballs are ... | |
| Proto rail and PMR | 4/14/2009 |
| Q: I was at exotic sports the other day and they had the proto rail for 274$ and beside it the pmr for ... A: The PMR is the Proto Rail Matrix. In 2007 the PMR was released and later in 2008 the UL PMR ... | |
| Trigger pull | 4/9/2009 |
| Q: I just bought a cyclone feed for my 98 custom that already has a response trigger. I tried to fire ... A: the reason why the trigger becomes tight is because the flowvalve is closed. on the side of the grip ... | |
| Gas Thru Foregrip | 2/17/2009 |
| Q: I am looking at purchasing a Viewloader Lancer as a back up marker. These markers do not come with ... A: You would have to buy an ASA/regulator adapter. I am not sure if there are any adapters out like ... | |
| tippmann 98 barrel | 2/13/2009 |
| Q: hey i am having some trouble i have played paintball for about 4 years now but i have had trouble ... A: If your looking for accuracy i would go with a All American or better yet the Linear barrel. I would ... | |
| Low pressure kit? | 2/3/2009 |
| Q: I have a tippmann 98 and a hugh woodsball play. I'm running CO2 in to my 98. I want to get a low ... A: If you plan on using CO2, the expansion chamber kit would be what you have wanted. If you bought a ... | |
| Not shooting | 1/27/2009 |
| Q: I have an electronic trigger spyder imagine, the problem is everytime i cock it back to shoot,it ... A: It's a possibility that it is the battery. The OEM rechargeable batteries are notorious for dying ... | |
| attaching crossfire N2 tank | 1/27/2009 |
| Q: I purchased a indian creek promaster and a N2 45/4500psi tank and am wondering how to attach it? ... A: normally a standard tank just screws into the asa which is on the bottom of the trigger frame. There ... | |
| parts | 1/26/2009 |
| Q: i have a tippmann 98 an my front sight spring broke and the part that keeps my hopper attached to my ... A: it sounds like either the "U" spring broke, bent out of shape, or you lost the "U" spring. Also if ... | |
| paintball mask | 1/23/2009 |
| Q: need help for my own safety i have a full face paintball mask it has a chin visor which i always ... A: how old is the mask? it could be the straps have gone bad and the goggles are in need of new straps. ... | |
| Spyder MR1 Misfires....? | 1/6/2009 |
| Q: My Spyder MR1 is brand new and I love it. However, when I was playing I noticed that my frame was ... A: yup, everything is normal. If the frame is not tightened it will lower the sear which lowers the ... | |
| new gun | 1/3/2009 |
| Q: im starting to get into tournament play and im thinking about getting a new gun. i have a spyder vs2 ... A: I would recommend getting a Proto SLG if you can still find them. If your able to afford the extra ... | |
| Viewloader High Voltage Marker | 1/2/2009 |
| Q: and i want to mod it for rebound and shoot faster without freezing and stuff... Think you can help ... A: All you will need is compressed air instead of the usage of CO2. Compressed air is cleaner for the ... | |
| paintball gun question | 12/28/2008 |
| Q: is there a regulator for a jt tac-5 recon paintball marker? ANSWER: no there is not. ---------- ... A: yes, you can put a regulator on a tac-5 but then you will need to change all the internals to ... | |
| compressed air | 12/27/2008 |
| Q: what is required to convert a compressed air gun to co2, my son wanted co2 and i got compressed air ... A: Some guns work specifically with Compressed air. Compressed air is cleaner for the gun and ... | |
| cost of n02 | 12/26/2008 |
| Q: How much does it cost to fill a n02 tank and how many balls could it shoot refering to like a 20oz ... A: It depends on the size and how much pressure the tank holds. At our store we charge $4 for a 3000psi ... | |
| tippmann pro-lite | 12/7/2008 |
| Q: i was wondering if there's any way that i can make the trigger pull on my pro- lite easier. it's ... A: You'd have to get a new sear spring You can try Acer Hardware or Home depot (but be aware, it needs ... | |
| Tac-5 Recon | 12/7/2008 |
| Q: My Tac-5 Recon is leaking Co2 air from inside the housing of the gun. Im assuming that a seal has ... A: your best bet is to look online for close by stores or fields. I would recommend pbnation.com and ... | |
| Spyder VS1 tweak | 12/6/2008 |
| Q: Is it possible to convert the VS1 full auto? A: Yes it is possible top convert it to have full auto, you will need to upgrade the board. I would ... | |
| markers | 12/3/2008 |
| Q: should i get an invert mini or A-5 A: It depends on what you want to do in terms of playing. If you were to go into speedball, the Invert ... | |
| pm8 | 12/1/2008 |
| Q: im not sure which tank i should get for my pm8 i just bought a 68/45 low pressure tank.....i was ... A: You will be fine with a LP output tank. The reason for a LP and HP tank set-up is that some guns ... | |
| paintball repair | 11/12/2008 |
| Q: my tippman 98 custom will not fire has brand new co2 20 oz tank i was told it might have bad seals ... A: Did you cock the gun before firing? Is the tank full? Is it an electronic? If the gun is an ... | |
| paint ball gun problems | 11/1/2008 |
| Q: i got a view loader triad and a co2 tank for it . the tank was full and screwd on to the gun and i ... A: There could be a problem with the sear or trigger assembly. My suggestion is to send it to a ... | |
| pm8 | 10/28/2008 |
| Q: i was debating on what gun to get because i was joining my schools speedball team...we arent ... A: That is a hell of a deal for that price. Proto has not released a PM9 nor do i believe they are ... | |
| spyder pilot | 10/11/2008 |
| Q: i have a spyder pilot 08 with eye and the gun was cocked and i put c02 in and turned it on and it ... A: Is the gun turned on? is there a fresh battery in the grip? If the battery is rechargeable, have ... | |
| Tippmann A-5 trigger mod | 10/8/2008 |
| Q: I just made a homemade mod for my A-5 semi-auto trigger but since I don't have my CO2 tank right ... A: No problems should occur with CO2 or Nitrogen/Compressed Air. I have done the same to my personal ... | |
| proto slg | 10/7/2008 |
| Q: hey so i just bought a proto slg and was having some role back problems. when i put a paitball in ... A: the eyes ont eh gun should not turn of if a ball is placed int he breech and the gun tilted ... | |
| paintball | 10/1/2008 |
| Q: what is the comparison between air and power thanks A: there is no real comparison, factors come into play too much. Such as how fast the air is released ... | |
| SLG and tank...again.. | 9/21/2008 |
| Q: I've decided im going to get a 4500psi tank but i've been looking and i find some that say "fixed ... A: the high pressured and low pressure are just the different psi outputs on the tank. A High Pressure ... | |
| can i know | 9/11/2008 |
| Q: i have a tippmann A5 and i bought the low pressure kit, and i would like to know if can i use the ... A: yes you can but it will be inconsistent. Please also note you must use a regulator in order to ... | |
| Distance | 9/9/2008 |
| Q: I was looking for a sim type paintball marker that shot fairly far and accurate but I read that ... A: Do not compare Walmart guns such as Tippmann, Kingmann, and Brass eagles with guns such as Dye, ... | |
| My gun | 9/9/2008 |
| Q: ok me and my friend have been playing paintball for a wile and the other day we were asked to join a ... A: yes a spyder would be good to use. You can add a stock as some manufacturers make stocks that mount ... | |
| APE Rampage Circuit Board For Tippmann X7 | 9/8/2008 |
| Q: how fast can you program it up to (20 bps) or what and can it work with the double trigger kit. ... A: no the board is tournament legal. Most companies that make aftermarket boards take into ... | |
| APE Rampage Circuit Board For Tippmann X7 | 9/8/2008 |
| Q: how fast can you program it up to (20 bps) or what and can it work with the double trigger kit. ... A: there are 9 modes; semi, burst, reactive, full auto, turbo, rampage, psp, nxl, and idle (Technically ... | |
| Spyder Sonix Pro | 9/6/2008 |
| Q: My marker has really hig fps. I tried to turn it down but will not go to a lower fps. How can I fix ... A: you will have to back out velocity adjuster all the way. If that doesn't work and the gun's pressure ... | |
| Poppit | 9/5/2008 |
| Q: My Angel 04 speed has a massive air leak out of the barrel, I talked to a guy who knows all about ... A: It's honestly all up to you, if the gn has been good to you in terms of not breaking down a lot, ... | |
| Poppit | 9/4/2008 |
| Q: My Angel 04 speed has a massive air leak out of the barrel, I talked to a guy who knows all about ... A: It can be 1 of 4 things or a combination of all: 1. Poppit Seat is bad and you'll need a new poppit ... | |
| tippmann x7 | 9/3/2008 |
| Q: Should i get a different barrel or a flatline barrel? ANSWER: It's pretty much what you want out of ... A: no, the flatline does not increase accuracy, the flatline was meant to put a back spin on the ball ... | |
| paintball vests | 9/3/2008 |
| Q: ok now i want to get a paintball vest with to gun holsters on it.but the only thing is i dont want ... A: I would recommend a PCS Vest or a NXE vest. They were make to carry what you can; cell phone, pods, ... | |
| tippmann x7 | 9/1/2008 |
| Q: Should i get a different barrel or a flatline barrel? A: It's pretty much what you want out of it. If you want better effiency and better accuracy I ... | |
| tippmann x7 | 9/1/2008 |
| Q: is it a big gas hog?.. want can i do to reduce it.........should i get a different barrel or a ... A: You won't be able to do much for an X7 in terms of increasing the efficiency. You can however ... | |
| 98Custom compressed Air | 9/1/2008 |
| Q: I have recently got a 98 custom a.c.t. and i am really interested on using compressed air for adding ... A: All you will need is a HP output tank. The pressure that outputs out of a HP is the same pressure of ... | |
| paintball guns | 8/31/2008 |
| Q: i am a begginer and my friends genrally dont know alot about guns. i dont know if i should et a ... A: Typically, yes I would go for a beginner package as that is what you will need in order to play. ... | |
| jt-tac 5 marker problems | 8/30/2008 |
| Q: i have a jt-tac 5 paintball marker and when i put in the co2 tank the air does not go in the gun. i ... A: Have you filled your CO2 tank? Is your CO2 tank empty? Where you screw in your tank, do you see a ... | |
| spyder extra | 8/30/2008 |
| Q: is it any good? A: Yes. In my eyes, a gun is a gun is a gun. The only difference between guns are the type of operation ... | |
| DIY Cylinder Refills | 8/28/2008 |
| Q: We're having a paintball birthday party for my son this weekend. Instead of paying $20.00 / kid at ... A: sorry for the late reply, i could have sworn i hit the send answer button before. Thankfully ... | |
| Regarding equipments | 8/26/2008 |
| Q: I am sandeep, i am looking out to set up a field of my own in Bangalore, India. I am looking for ... A: Tippmann would be a great company to go with, the guns require little maintenace and were made to ... | |
| tippmann x7 | 8/19/2008 |
| Q: wht kind of paint should i use w/ tippmann x7? A: Any paint would do, i would avoid using the premium professional paint such as hellfire as it is ... | |
| tippmann x-7 | 8/18/2008 |
| Q: i was just wondering i have a tippmann x-7 with e-trigger and cyclone feed system? and with it what ... A: you should get a 68/4500 tank. That or a 47/3000 tank but with that you'll only get a few hundred ... | |
| tippmann x-7 | 8/18/2008 |
| Q: i was just wondering i have a tippmann x-7 with e-trigger and cyclone feed system? and with it what ... A: Tippmanns were made to be used with CO2, thats how they are built. But it is an even better option ... | |
| autococker jams | 8/17/2008 |
| Q: my war games auto-cocker keeps jamming up and i don't know how to stop it. i have an automatic ... A: if it's jamming, check to see that the breech clears fully when you pull the trigger, the back block ... | |
| etek2/PM8 | 8/12/2008 |
| Q: is it worth the change from a PM8 to the etek2? the rest of my team use planet eclipse markers etc A: This is a difficult question to answer so i am going to try my best. The Proto M8 is a flagship ... | |
| Paintball gun....and Sponsers?? | 8/11/2008 |
| Q: Ok I have a Spyder Electra that is blowing out all of the gas the first time i shoot it...i have a ... A: have you given the gun a thorough cleaning and relubrication? what is it that it is exactly doing? ... | |
| Proto SLG vs. Smart Parts | 8/7/2008 |
| Q: I want to get rid of my '05 Spyder Pilot and the two markers that I'm looking at are the Proto SLG ... A: Get the SLG. It's a lot easier to maintain and for the money it's a lot better than the ION in terms ... | |
| Braided Line | 8/1/2008 |
| Q: I recently unscrewed my braided line from the tombstone to swap it with a new braided line. They are ... A: if it's able to screw back on without hesitation or a lot of force/torque, then you should only need ... | |
| Walking the trigger | 8/1/2008 |
| Q: My son has a PMR. He says when he's walking the trigger the marker doesn't fire everytime he pulls ... A: With The pmr, the stock trigger is kind of hard to walk. take a punch and a hammer and tap out the ... | |
| PMR constant leaks and asa problem | 7/28/2008 |
| Q: i bought a pmr(proto matrix rail) a month ago and ever since the first shot it's leaked. ive lost ... A: You can opt for a custom products reg but you can also contact dye and ask for a replacement. All ... | |
| pmr trouble | 7/28/2008 |
| Q: my pmr doesnt shoot far..at all. i just shoot it at chrono and it came out at 279. i bought a new ... A: Paintballs will not shoot straight unless an alternative force is putting a spin on the ball (Apex ... | |
| PMR constant leaks and asa problem | 7/28/2008 |
| Q: i bought a pmr(proto matrix rail) a month ago and ever since the first shot it's leaked. ive lost ... A: Would the second crack from the top of the regulator be where the swivel point is on the regulator? ... | |
| paintball barrel | 7/17/2008 |
| Q: I want to get a J&J ceramic precision barrel for my spyder VS2. Is there a difference between 14 ... A: I would recommend sticking with a 14", the extra porting is not really worthwhile. Also, having a ... | |
| Gun? | 7/16/2008 |
| Q: I am looking to buy my first gun and I am having trouble on deciding on one. I have about 250 ... A: out of those 3, your gonna love the Proto SLG. We have sold many at the store and there are very few ... | |
| proto slg | 7/11/2008 |
| Q: hey i heard u no everything well can i run co2 on my slg if i use a remote line? if i did what would ... A: It is best not to run CO2. The proto SLG is meant to be run off compressed air which will prolong ... | |
| camo | 7/10/2008 |
| Q: I recently bought a burlap camo blanket. in your opinion, do burlap camo blankets work good? A: Do you mean a ghillie suit? It is mainly used in hunting, militia, covert ops, etc the sort of like. ... | |
| Spyder pilot acs | 7/9/2008 |
| Q: Do you need to cock the the gun every time you shoot? A: not every time you shoot. You have to initially cock it first before shooting. It's like turning an ... | |
| Repair | 7/9/2008 |
| Q: The striker on my Spyder Vs1 is not hitting the sear hard enough. any ideas? ANSWER: make sure the ... A: Yes that is the solenoid, does it seem to be properly working? are you using the stock rechargeable ... | |
| Repair | 7/9/2008 |
| Q: The striker on my Spyder Vs1 is not hitting the sear hard enough. any ideas? A: make sure the bolt and hammer are clean. Replace any orings that look swollen or torn. Use gun oil ... | |
| jt usa Tac-5 recon | 7/8/2008 |
| Q: I have the jt usa tac-5 recon gun and i used it a couple times then had some O ring problems. I took ... A: Sounds like you are missing a piece. On the hammer, there should be a pin that sets the cocking ... | |
| how to change over to air | 7/7/2008 |
| Q: i have a tippmann custom pro how do i change it over to air when it is on co2? A: You can change over right out of the box. Just be sure you are using a High pressure bottle as low ... | |
| paintball | 7/7/2008 |
| Q: I have a spider vs2 but the problem is when I screw on the tank and turn the knob the gun does not ... A: Be sure the tank is filled. Sometimes the pin in the regulator/asa on the spyder guns falls out, ... | |
| Spyder pilot acs | 7/7/2008 |
| Q: ok i heard from a friend that if you use a co2 tank for your electronic gun it will mess it up, he ... A: A Gun is only a "true" electronic gun if it has a pneumatic solenoid. An example of these guns are ... | |
| My Ion wont turn on | 7/4/2008 |
| Q: I just bout a new smart parts Ion gun the other day, before leaving the store they were testing it ... A: sorry for the late answer, i forgot to put my vacation days on allexperts. Your best bet is to get ... | |
| 98 custom upgrades and co2 | 7/2/2008 |
| Q: i want to buy a 98 custom and i want upgrades too [the upgrades i want] 1.m4 stock 2.barrel[what ... A: For a barrel, i would recommend a 1 piece J&J ceramic barrel. The tippmann community and I are huge ... | |
| spyder MR-1 feedneck screw stripped | 7/1/2008 |
| Q: Can you help me please? i stripped my paintball marker's feedneck screw on the marker itself.There ... A: in order to fix a stripped hole you will need to repair it via helicoil. Due to the nature of ... | |
| Sypder electra | 6/26/2008 |
| Q: I have the first spyder electra. I have less then 10 games on it so it is fairly new. I went to use ... A: have you made sure air is getting into the gun? Some times the pin wear down on both the asa and the ... | |
| trigger sensitivity | 6/25/2008 |
| Q: Is it possible to adjust the trigger sense? If so i need directions. A: It would have to depend on the switch type (optical or leaf spring). For an optical trigger there ... | |
| rex type r | 6/20/2008 |
| Q: i need to no how and what i can mod on my rex i love the gun the way it is but of course i need to ... A: sorry for the long reply, the paintball store is quite busy and haven't had the time to answer your ... | |
| rex type r | 6/20/2008 |
| Q: i need to no how and what i can mod on my rex i love the gun the way it is but of course i need to ... A: I have actually worked on this gun once and it was quite the experience. This gun is very similar to ... | |
| spyder pilot | 6/18/2008 |
| Q: i recently got a spyder pilot acs and a 12 oz co2 tank but whenever i actually play my gun ... A: Do you hear a loud pop when you fire the gun? does it properly recock? it's very hard to try and ... | |
| spyder pilot | 6/18/2008 |
| Q: i recently got a spyder pilot acs and a 12 oz co2 tank but whenever i actually play my gun ... A: Have you made sure the gun is recocking properly after you fire it? Are you using a filled CO2 tank? ... | |
| nitro tank problem | 6/15/2008 |
| Q: i have a spyder vs2 and 48ci/3000 psi air tank for my gun. whenever i put the tank on the gun and ... A: Bring it back to the store and ask for a replacement regulator or rebuild. There's not really much ... | |
| Barrel | 6/13/2008 |
| Q: Wat's up, I was wondering about a mod fro my X7 I am currently the Sniper for my team in Woodsball I ... A: Any barrel greater than 14-16" is never worth the price tag. You will end up losing a great amount ... | |
| Smart Parts SP8 | 6/9/2008 |
| Q: I just bought a Smart Parts SP8, I've used C02 on my other guns but i was wondering if it's okay to ... A: For the of electro pneumatic guns I would advise not to use CO2 on a the gun. But in this case, the ... | |
| Dangerous Power G3 | 6/6/2008 |
| Q: i recently purchased my new G3 from a local Paintball store. i got it home, set it up with a 4500 ... A: Things to take steps to make sure it's working: 1. Make sure you are using Fresh 9v batteries in ... | |
| Starting a business | 6/4/2008 |
| Q: im wanting to start a paintball business in a small town with a pop of 40,000 people. I have a good ... A: You will need a lot of money and a lot of pull. If you don't not know anything about paintball you ... | |
| Etek2 V.S. Shocker NXT V.S. PM8 | 6/3/2008 |
| Q: What do you think of the three guns pros and cons of each and what whould you recomend. A: The etek is a good all around gun but for the price you can get something better. The etek is a ... | |
| is the A5 a real upgrade for the 98? | 5/29/2008 |
| Q: I have been doing a lot of research about the A5, 98 custom, and X7. I have found out the X7 has to ... A: To be brutally honest, Yes, all the tippmann guns are the same. The only differences are the shells, ... | |
| Co2 and lancer not recocking | 5/28/2008 |
| Q: I bought a paint ball gun off of paintball-dicounters.com and i got a VL Lancer i havent shot it ... A: to know if your CO2 tank is filled it is done by weight and volume. Since CO2 is a liquid, when ... | |
| 32 Degrees remote airline w/quick disconnect | 5/26/2008 |
| Q: I have a quick disconnect remote line but it does not have slide check, I cant take it off my x7 ... A: You cannot, unless you have a friend with you to turn off the hose for you and then you dry fire to ... | |
| Velocity Adjustment on a Smart Parts Ion | 5/24/2008 |
| Q: I recently purchased a Smart Parts Ion on Ebay. I didn't recieve a manual with it but I figured it ... A: no, that is a bolt out back mod. Most ION owners modify their gums to look and compete with higher ... | |
| air leaking on back of proto slg | 5/21/2008 |
| Q: have air leaking past bleed valve on back of gun have replaced all with new o-rings but no prevail ... A: have you tried raising the regulator pressure or lowering it? sometimes a gum needs to seal at a ... | |
| air leaking on back of proto slg | 5/20/2008 |
| Q: have air leaking past bleed valve on back of gun have replaced all with new o-rings but no prevail ... A: Have you tried pressing the bleed valve while air was in the gun? Also, have you tried dismantling ... | |
| slg vs epiphany | 5/20/2008 |
| Q: is a proto slg better or worse or just as good as a smart parts epiphany? ANSWER: The SLG is a sear ... A: The PMR is a spool valve operated marker which uses a pneumatic solenoid and patented boost ... | |
| Sound vs. Eyes | 5/19/2008 |
| Q: Is sound activation better than Eyes in a hopper? I was going to buy a empire reloader b? A: They work basically the same. There only difference is a beam break/bounce beam uses light to sense ... | |
| slg vs epiphany | 5/18/2008 |
| Q: is a proto slg better or worse or just as good as a smart parts epiphany? ANSWER: The SLG is a sear ... A: The Alias was a top of the line Bob Long gun back in 2006, it was their flagship marker at the time. ... | |
| electronic paintball markers | 5/18/2008 |
| Q: what is the difference between electronic paintball markers and regular one's? and which one is ... A: Electronic paintball guns require a battery, board, and solenoid. A regular Paintball gun has a ... | |
| Silencers | 5/18/2008 |
| Q: I was going to buy a gemtech thread-on silencer for my Spyder MR2. I would put it on my recon rifled ... A: Silencers are illegal to use on any firearm or projectile. Other than that it should be used for ... | |
| autococker modifications | 5/16/2008 |
| Q: i have an autococker trilogy sport and i am looking to modify it a bit for a little more speed. i ... A: With proper timing and tuning the autococker will perform as well as any other paintball gun in the ... | |
| slg vs epiphany | 5/15/2008 |
| Q: is a proto slg better or worse or just as good as a smart parts epiphany? A: The SLG is a sear tripped balance spool. It works like a spyder but without a spring and is very ... | |
| epiphanys bps | 5/12/2008 |
| Q: How do i adjust how fast my stock epiphany can shoot. i wanna get it up to 17 and i dont think its ... A: I used this chart below on the link to help me get the bps setting i needed when i got an ion years ... | |
| barrels | 5/9/2008 |
| Q: Now my question is do i have to buy a specific barrel to fit the gun or can i buy any 12,14 inch ... A: The barrel threads you should get are Spyder threaded barrels. Every company that makes after market ... | |
| Spool Valve VS Poppit | 5/5/2008 |
| Q: What is the difference beetween a spool valve and a poppit? A: There are two main differences. A spool bolt is a single chambered gun, meaning the air chamber ... | |
| Position markers | 5/5/2008 |
| Q: What would be the best marker for each of the positions in woodsball? Commander, sniper, heavy ... A: There is no "best" marker for certain positions. It's about the player, the barrel, and the paint. ... | |
| Choosing a remote air system for your gun | 5/2/2008 |
| Q: I'm in the market for a remote air system for my 98 custom. As with any purchase, I like to do as ... A: All remote systems are basically the same, it would come down to preference and manufacturer, I tend ... | |
| Evil WGP Paintball Gun | 4/29/2008 |
| Q: I have an Evil WGP paintball gun. It's black with yellow letters. It takes nitrogen tanks and I was ... A: Without knowing other information such as parts and upgrades it would be hard to tell what it would ... | |
| Evil WGP Paintball Gun | 4/29/2008 |
| Q: I have an Evil WGP paintball gun. It's black with yellow letters. It takes nitrogen tanks and I was ... A: If you mean an Evil Omen (a closed bolt spyder) Then yes it can take either CO2 or Nitrogen tanks. A ... | |
| MR2 Anti-Chop Bolt and Eye | 4/29/2008 |
| Q: I have an MR2 with the anti chop bolt. How much of a difference is there between the eye and the ... A: The anti chop eye will allow the gun to only fire when there is a paintball int he breech, it has a ... | |
| Sniper Barrel | 4/29/2008 |
| Q: What would be the best sniper barrel for an MR2? I have a RAP4 super sniper barrel. ANSWER: Sorry ... A: You do not want sniper barrels, the way a paintball gun fires and the way paintballs are shaped and ... | |
| Paintball | 4/27/2008 |
| Q: how do i ajust the velocity on my 2005 spyder extra? And is this a good gun or not?thanx A: The spyder extra is a good recreation gun. To adjust the velocity the rear of the gun will have a ... | |
| Sniper Barrel | 4/27/2008 |
| Q: What would be the best sniper barrel for an MR2? I have a RAP4 super sniper barrel. A: Sorry to say, but those barrels are complete junk. Not only is it completely not air efficient, but ... | |
| MR2 vs. MR3 | 4/27/2008 |
| Q: Is the MR2 or MR3 better for woodland paintball? Is the MR3 worth it price wise? Is the MR2 standard ... A: They are both great for woods ball. With the MR2, You have 2 options, one with an anti-chop eye or ... | |
| Sniper Barrel on pilot | 4/25/2008 |
| Q: Do you think that a 20 inch ceramic sniper barrel on my spyder pilot 05 is decent? And what size of ... A: The 20+ inch barrels are all a gimmick. You will actually lose efficiency and the accuracy is quite ... | |
| Hoppers for the Sypder Electra | 4/24/2008 |
| Q: What hopper is better for the Electra, Halo B or Spyder Fasta? Thanks. A: Your not going to be shooting really fast with the Spyder Electra so the Fasta is a good choice if ... | |
| air tank for PMR marker | 4/22/2008 |
| Q: What type of tank should I get for the PMR it recommends a low pressure Is there a regulator I can ... A: You should get a LP tank if you plan on keeping the stock screw in asa (it's extremely hard to screw ... | |
| Age minimum | 4/19/2008 |
| Q: I was just wondering what the provincial law in Ontario says about the age requirment to BUY a ... A: You will have to call your local law enforcement and ask or go to a paintball specialty store and ... | |
| FPS | 4/7/2008 |
| Q: My friend is an idiot. He thinks an airsoft BB would slow down to about 10 FPS by the time it hit ... A: It really goes down to how far the target is from the initial exit of the barrel. The closer the bb ... | |
| High and Low | 4/7/2008 |
| Q: I feel really stupid asking this question. But I was in the market for a new air system and was ... A: Performance wise, it will be a lot better for guns that use an lpr. Reason being is that the HP tank ... | |
| autococker and the proper nitro tank | 4/3/2008 |
| Q: i have a wgp autococker trilogy comp. and i was wondering what sort of nitro tank i should get? ... A: 3000psi and 4500psi would be dictated by your wallet. The price difference is usually $100. Again, ... | |
| Modify | 4/2/2008 |
| Q: Sorry, but nobody is in the airsoft category and these are kind of similar... What kind of places ... A: Stretching would be a gain of usually 5-10fps. There always is a way to put things back together, ... | |
| CO2 AND NITROGEN | 4/1/2008 |
| Q: I have an ION XE and I am wondering if CO2 will screw up the internals or if it will damage the gun ... A: If park you mean field, yes. Nitrogen and CO2 are a big demand in the industry. If a field or store ... | |
| Modify | 4/1/2008 |
| Q: Sorry, but nobody is in the airsoft category and these are kind of similar... What kind of places ... A: You would want to bring your rifle to a specialty airsoft store. I am not sure where you'd be able ... | |
| Modify | 4/1/2008 |
| Q: Sorry, but nobody is in the airsoft category and these are kind of similar... What kind of places ... A: Ah, I haven't used my Marui Famas in a long time. Lucky for you i was into airsoft before going into ... | |
| CO2 AND NITROGEN | 4/1/2008 |
| Q: I have an ION XE and I am wondering if CO2 will screw up the internals or if it will damage the gun ... A: You can use CO2, but it is highly advised you bring your CO2 tanks and get it anti-siphoned. ... | |
| UPGRADING | 3/29/2008 |
| Q: Im upgrading from an Epiphany and m friend and I are staring a team (speedball). I'm looking for ... A: The main things I would do to an ION performance-wise, is a brand new bolt (I would recommend the ... | |
| Changing a preset HP air tank regulator to LP | 3/27/2008 |
| Q: I am aware that this can be done, but I lack the knowledge of how exactly I should change the ... A: You can run HP on a mini as it is regulated, it just takes some muscle to screw in the tank. Make ... | |
| Changing a preset HP air tank regulator to LP | 3/26/2008 |
| Q: I am aware that this can be done, but I lack the knowledge of how exactly I should change the ... A: If you do not know anything about air smithing, restrain yourself from taking apart the tank ... | |
| barrel | 3/26/2008 |
| Q: What would be a better barrel for sniping in a tippmann 98 custom, a flatline barrel or a 21 inch ... A: The flatline barrel is what you will be looking for. Paintball guns do not work like real guns where ... | |
| Loss of Power | 3/25/2008 |
| Q: My spyder sonix was purchased new a few months ago, and I have had few problems with it. However, ... A: Things to keep in mind when owning a blowback operation marker: 1. Are you running a full tank of ... | |
| New Barrell? | 3/25/2008 |
| Q: Ok, ive upgrading my pittmann 98 custom pro ive been looking around at barrells and im confused ... A: If anything, if you want to go all out, invest in a Dye UL Barrel. Or if your looking into something ... | |
| UPGRADING | 3/24/2008 |
| Q: Im upgrading from an Epiphany and m friend and I are staring a team (speedball). I'm looking for ... A: The thing about egos that I dislike is the kick and how loud they are. Poppet markers are often very ... | |
| Paintball Barrels | 3/23/2008 |
| Q: Ok say I have a spyder sonix pro and it comes with a 9" barrel. Is it possible to buy a barrel from ... A: yes, many companies make after market parts and barrel for the Kingmann Spyder line of markers. ... | |
| New Barrell? | 3/23/2008 |
| Q: Ok, ive upgrading my pittmann 98 custom pro ive been looking around at barrells and im confused ... A: I believe you meant your gun is a "TIPPMANN" 98 custom. The flatline is good, but it is absolutely ... | |
| CO2 vs Compressed air | 3/22/2008 |
| Q: Whats really the difference between CO2 and Compressed Air? Does it affect the gun or paintball in ... A: Because Fiber wrapped tanks weren't developed back then. Also, to compress air in mass was also ... | |
| Venturi Bolts | 3/20/2008 |
| Q: do you think that a Venturi bolt would make a difference for autococker trilogy i thought anything ... A: The venturi will make you run at a slightly higher pressure. Theres a lot of gimmick in venturi ... | |
| High-end | 3/12/2008 |
| Q: Ok I was looking to bump up to a high-end marker and got it down to three choices. Number one, the ... A: stay away from the angel one. We tech Angels and they are quite the headache; rams leak almost all ... | |
| barrel | 3/12/2008 |
| Q: i was wondering if an Tippmann Model 98 Flatline will fit on a bt-4 combat? and also if u kno of a ... A: no, only the A5 flatline will fit. If you want a good "long range barrel" i would recommend the BT ... | |
| High-end | 3/11/2008 |
| Q: Ok I was looking to bump up to a high-end marker and got it down to three choices. Number one, the ... A: Stay away from the shocker, you'll have the worst headache with that gun. The Etek and Etek2 is not ... | |
| Help With my chopping spyder Pilot ACS | 3/10/2008 |
| Q: Saturday was my first time paintballing and I just bought a Spyder Pilot ACS and I really did a lot ... A: The trigger is not adjusted right or you are out firing what the board can manage (assuming it is ... | |
| JT Tac-5 | 2/26/2008 |
| Q: Ok One of my friends Has a Tac-5 hes had for a while and he wants to get some mods for it and some ... A: The only items that will fit the jt tac-5 are the jt tac-5 specific upgrades such as their rear ... | |
| paintball size | 2/25/2008 |
| Q: Should the size of the paintball be the same as the bore size of the barrel? A: For a perfect fit it should yes. Paintballs and barrels work best together when their is the optimum ... | |
| Modifying Tippman 98C | 2/24/2008 |
| Q: Ive owned my Tippman 98C for a little over a year now and really haven't been able to play much ... A: If you want more performance and efficiency added to your list of previous "wants" I would get a LP ... | |
| paintball | 2/23/2008 |
| Q: I got a spyder sonix pro for Christmas last year and have recently been looking at several ... A: In my opinion, it's not worth upgrading a Spyder with fancy internals unless it's an electronic gun ... | |
| paintball | 2/23/2008 |
| Q: I got a spyder sonix pro for Christmas last year and have recently been looking at several ... A: Yes both items will work but the spyder sonix is meant to be run at high pressure (800psi) and not ... | |
| V-Force mask | 2/21/2008 |
| Q: My name is wynand. Irecently bought myself a vforce armour mask and i am strougling to remove the ... A: You will need to remove the straps. From what i know of V-forfce masks, the strap is held in via ... | |
| V-force GRILL | 2/19/2008 |
| Q: i have a cheap JTusa mask and when i play it get super foggy and i can't see anything, i've heard ... A: Most thermal lenses have a thin removable film that protects the thermal plastic while still in ... | |
| Tippmann a5 | 2/19/2008 |
| Q: i want to make sure about the tippmann a5 aluminum power tube and the bolt upgrade, i want to know ... A: to be honest, you won't see much of a difference with that aluminum power tube and the stock tube ... | |
| electronic marker | 2/17/2008 |
| Q: ok i have a spyder pilot acs and my trigger handle that came on the marker has a rechargeable ... A: Just because the battery only goes up to 9.4 doesn't mean it's not fully charged. The board is a ... | |
| Tippmann A5 | 2/17/2008 |
| Q: i own a tippmann A5 paintball marker and i've read what you said about mags but still i just got one ... A: notify the manufacturer of the expansion chamber on obtaining the line. Another route you can go ... | |
| Damaged Tippmann Air Feed Line | 2/15/2008 |
| Q: Tippmann 68 carbine. The air feed line into the marker. The threads are stripped out. That is all ... A: There is not much you can do if you stripped out the threads (if the threads are stripped out on the ... | |
| ?? | 2/13/2008 |
| Q: i just recently purchased a Rex R3, but i have an old Black Dragun... Ive noticed the Rex uses more ... A: without fine tuning of the marker you will go through air like water. Lower the dwell and raise it ... | |
| co2 leak | 2/13/2008 |
| Q: i have a spyder imagine and when ipull the co2 tank off it leaks. it develops a small leak on or ... A: Spyder don't usually come with an on/off with bleeding system to unpressurize the gun. Chances are ... | |
| Ion LP or HP? | 2/11/2008 |
| Q: I am wondering if I should use low pressure or high pressure for my stock ion. Can you help? A: If you have the basic ION with a duck bill or an on/off that presses the tank pin when the tank is ... | |
| Bt Ironhorse. | 2/11/2008 |
| Q: Thinking about buying a BT Ironhorse. What can you tell me. This will be my first paintball marker ... A: The Bt-ironhorse is like any other gun that's a blowback operation. It will meet your "woodsball" ... | |
| paintball markers | 2/9/2008 |
| Q: i hear everyone talking about psi and velocity and to be onist i do not have a clue what it is... ... A: PSI is pounds per square inch. In this case, it's pounds per square inch of air pressure. That ... | |
| VL lancer | 2/3/2008 |
| Q: when i fire my gun it keeps firen after with out me pressin it.... wats the problem....? A: Is your tank low on air? When a tank is low on air it will not provide enough pressure to return the ... | |
| Running Co2 in a gun set up for nitrogen | 1/30/2008 |
| Q: will running co2 in my autococker set up for compressed air screw it up. i heard an anti-siphon on ... A: I would advise to not run CO2 in any gun that requires regulated air. You can damage the regulators ... | |
| gun | 1/25/2008 |
| Q: what is a good kinda cheat gun that shoot good with co2 A: I am guessing you meant "cheap" not "cheat". A Spyder is very CO2 friendly as it has the expansion ... | |
| ion | 1/24/2008 |
| Q: i have a smart parts ion. i can shoot the gun a few times then it turns off it is not a low battery ... A: Make sure you are using a brand name battery such as Duracell. Make sure the button membrane isn't ... | |
| my gun | 1/23/2008 |
| Q: i have a smart parts ion and i have to use co2 is there anything i need extra? A: I would not use CO2 with any electro pneumatic gun. You will damage the internals. An Ion is fine ... | |
| air/n2/or co2 | 1/22/2008 |
| Q: what are the performance differents between n2 and co2, also n2 and air? A: Nitrogen is normal air. Though pure N is denser than air. The major differences between ... | |
| triad accuracy | 1/22/2008 |
| Q: I have a VL triad with a 14 in empire twister barrel and would like to know what I can do to make it ... A: The only way to make your gun more "accurate is good paint to bore match. Each barrel bore is ... | |
| high or low pressure on my ION? | 1/21/2008 |
| Q: Hey Regis, I was wondering-- Would a high or low pressure air tank be better for my ION with a CP ... A: You can go either or. If you have the screw in asa, i would advise LP because you can screw in the ... | |
| qev and nirogen tanks | 1/21/2008 |
| Q: What is a QEV and what does it do? Can I fill up a nitrogen tank with a regular air compresser? ... A: A QEV is not needed but if you want to show off the speed of your gun you might want one. In todays ... | |
| qev and nirogen tanks | 1/21/2008 |
| Q: What is a QEV and what does it do? Can I fill up a nitrogen tank with a regular air compresser? A: A QEV is a Quick Exhaust Valve that will allow you to exhaust the air out of a chamber faster than ... | |
| 3 or 5 year hydro tanks | 1/21/2008 |
| Q: Do you know how to determine how many years a compressed air/nitrogen tank can last? I understand ... A: Googling the dot ID number would eb your best bet, there's a lot of different manufactured tanks. It ... | |
| A-5 on high pressure Nitro | 1/17/2008 |
| Q: I have heard that the A-5 doesn't work very well with a nitro system. I don't know if people are ... A: The a5 with response would actually work better. There's greater consistency and efficiency when ... | |
| High Pressure vs. Low Pressure Nitro Systems | 1/16/2008 |
| Q: I have a Tippmann A-5, response trigger, flatline, and car sliding stock setup. I also wear a ... A: After five years you need to send it to a scuba shop and they will test to make sure the tank is ... | |
| High Pressure vs. Low Pressure Nitro Systems | 1/16/2008 |
| Q: I have a Tippmann A-5, response trigger, flatline, and car sliding stock setup. I also wear a ... A: you'll want a high pressure tank, blowback markers were designed to be used with high pressure ... | |
| paint keeps breaking | 1/14/2008 |
| Q: I have a problem with paint that keeps breaking in my spyder pilot acs. I fired it cleaned it then ... A: is it breaking in the barrel or breaking in the breech? If it's breaking in the barrel find a ... | |
| wat gun should i buy | 1/12/2008 |
| Q: i have been deciding wat gun i should get for a while and ive narrowed it down to the vs3 and the ... A: i would recommend either a Reloader B2 or a Velocity Junior. Both are top of the line hoppers and ... | |
| wat gun should i buy | 1/12/2008 |
| Q: i have been deciding wat gun i should get for a while and ive narrowed it down to the vs3 and the ... A: The regular ION is the base gun. It has a screw in asa, generic feedneck, 1 piece barrel. All that i ... | |
| wat gun should i buy | 1/12/2008 |
| Q: i have been deciding wat gun i should get for a while and ive narrowed it down to the vs3 and the ... A: I would say go with the ION, it's a great electropneumatic gun at a great price. It's got the modes ... | |
| DM7 | 1/8/2008 |
| Q: I have a DM7 that i have used only once. It is now leaking through the rear of the bolt, and i was ... A: As per manual, change the number 11 orings on the tail of the bolt. To adjust the pressure take a ... | |
| convert from co2 to air | 1/6/2008 |
| Q: I have a spyder paint ball gun and was wondering if I could change over to compressed air instead of ... A: You cannot put compressed air into a CO2 bottle... ...well you can it just won't work out the way ... | |
| Helppppp Me PLeeease | 12/29/2007 |
| Q: OK well i just bought a Proto Slg...got it home nice gun i shot about 1500 rounds through it over ... A: the slg is a different type of marker. i wish i owned one so i could take it apart and find out all ... | |
| barrel | 12/28/2007 |
| Q: like i want to buy a new barrel for a gun like does it get better the longer or what is the ideal ... A: no the longer the barrel does not mean the more accurate or efficient. Ideally, anything over 14" ... | |
| vl traid | 12/26/2007 |
| Q: ok i got a green viewloader triad and i am a beginner so go easy i put the tank on it has air in it. ... A: Make sure your CO2 tank is fully filled. cock the bolt back (the silver pin on top of the gun) and ... | |
| vl traid | 12/26/2007 |
| Q: ok i got a green viewloader triad and i am a beginner so go easy i put the tank on it has air in it. ... A: The Triad is not an electropneumatic gun and does not cock back automatically. Have your cocked the ... | |
| paintball gun help | 12/26/2007 |
| Q: how do i put a hopper on a proto Slg paintball marker ive tried and it wont fit i hav also tried ... A: The sad thing with low level entry markers is that do not having a clamping feedneck. You'll want to ... | |
| N2 on a Syder Xtra | 12/25/2007 |
| Q: I am new to the sport and just wanted to get into it and heard that the Spyder Xtra was a good ... A: The Spyder xtra is a decent beginners gun and it ca use either CO2 or compressed air. If anything ... | |
| low pressure and high pressure tanks | 12/24/2007 |
| Q: just bought a angel g7 . do i need a low pressure or high pressure tank? Also bought my little ... A: Witht he newer angels (a4 and up) you'll want to use a low pressure tank. You can use a High ... | |
| how to get sponcered | 12/22/2007 |
| Q: how can my paintball speedball team get sponcered. we live in charlston south carolina we are ... A: be active in the tournament paintball community. Sign up on the APPA website ... | |
| -air- | 12/19/2007 |
| Q: i have recently purchased a Tippmann A5 with a responce trigger and flatline barrel, i played on a ... A: With the amount of money you will invest to increase efficiency you can buy a new gun, one that will ... | |
| Accuracy | 12/18/2007 |
| Q: We need accuracy at 40 meters with a X7 can you help me? My X7 is fitted with flatline barrel and 20 ... A: Flatline barrels were not meant for accuracy, they are meant for long range shooting (and IMO less ... | |
| paint ball business | 12/13/2007 |
| Q: im from ireland and have my own land in a great location just outside dublin city(biggest city in ... A: you'll need netting to protect the spectators and and a tech to service guns on site. You'll need to ... | |
| paint ball business | 12/12/2007 |
| Q: im from ireland and have my own land in a great location just outside dublin city(biggest city in ... A: truth be told, If you don't know anything about paintball and it's current trends, it's not worth ... | |
| Handle freezing | 11/30/2007 |
| Q: Hey, I use my tl-r in the winter a lot and the front grip always freezes up because of the air ... A: From what I know and seen, i do not believe someone sells a rubber cover for the fore grip. ... | |
| piantball accruacy | 11/29/2007 |
| Q: if you increase the psi in a paint ball gun will it make your shots more accruate A: no it will not, at a certain paint due to air friction and impact it will actually veer off from ... | |
| programing | 11/25/2007 |
| Q: how do you program a eos smart part gun board bought new need to explain it to me having trouble ... A: Open the grip and turn the power on, press the programming button and note in the manual which mode ... | |
| Which barrel is best for the Spyder TL-R | 11/16/2007 |
| Q: Hey, I'm looking to buy my bro a new barrel for his spyder tl-r, probably a 12 inch. Which ... A: One of the best barrels out there is the Dye Ultralite barrel. It's a two piece stepped bored barrel ... | |
| HPA in a aluminum Co2 tank& sponsors | 11/11/2007 |
| Q: but that is not the reason why I'm typing this e-mail i have 2 questions question 1 is it ok to put ... A: 1. No you cannot fill CO2 tanks with HPA, you'd only be able to fill to 800psi and you'd get maybe ... | |
| Tippman 98 custom | 11/1/2007 |
| Q: I have had a tippman 98 custom for a few years and I want to start to upgrade it. I want to start ... A: a rifled barrel is a specially bored barrel that will put a side spin on the ball in an attempt to ... | |
| Differences | 10/29/2007 |
| Q: What are the differences between Kingman 2007 Spyder Sonix Paintball guns and Kingman 07 Spyder ... A: they are both the exact same gun. With the exception of the VS series, the sonix and victor shoot ... | |
| Paintball markers and air systems | 10/29/2007 |
| Q: I am ready to buy a PB gun but don't know what to buy. So, could you recommend me a good marker for ... A: The Smart Parts ION, the new Proto SLG, Indian Creek Designs Promaster, and Spyder VS series are all ... | |
| Bob Long or Ego | 10/27/2007 |
| Q: Do you think i should get a bob long marq 7 or an ego eclipse? Explain. Are either ones bulky, ... A: to be honest, though the way the marq and ego operate, you'll hardly notice one is "better" than the ... | |
| spyder | 10/25/2007 |
| Q: does a spyder vs3 come with an autococker already installed? A: I am going to try and go on a limb on what you are trying to ask. An "autococker" is a type of ... | |
| Tippman 98 custom | 10/25/2007 |
| Q: I have had a tippman 98 custom for a few years and I want to start to upgrade it. I want to start ... A: You want to stray away from the "Longer barrels = better accuracy". That statement only pertains to ... | |
| my hopper | 10/22/2007 |
| Q: i just got a new empire hopper with loader b but i dont know how to program it right A: This is straight from the manual, on the bottom is my summarization if you don't wanna read the ... | |
| paintball | 10/21/2007 |
| Q: of team Unleashed. I have a team of 7 and we are 17,18,19,20,21,22,22 years old, we have been ... A: You can enter the NPPL, PSP, GPL, APL etc. (there are a lot of promotional tournaments). Visit their ... | |
| Autococker Superstock SF. low velocity | 10/20/2007 |
| Q: I just got this autococker opened it up, put on the air, and there was an air leak in the expansion ... A: the super stock has a regulator, you want to increase the amount of pressure into the gun. please ... | |
| feeding elbow | 10/16/2007 |
| Q: for an autococker trilogy tactical, do you need to buy a feeding elbow with it or does the hopper ... A: supposedly a hopper will fit on but you will need to sand the neck of the hopper because not all ... | |
| The barrel guy again | 10/11/2007 |
| Q: Thanx for the advice man. next time i'll know. just had a few follow-up questions. first, were you ... A: BT makes 2 different types, the Apex barrel and the Apex barrel tip (which is just the adjuster ... | |
| kingman spyder pilot malfunction | 10/11/2007 |
| Q: I have a Kingman Spyder Pilot Paintball Gun. When I set it on any function, and shoot it, it shoots ... A: remove the bolt and hammer assembly from the gun, clean it and make sure the bolt and hammer are ... | |
| Barrel | 10/11/2007 |
| Q: i just ordered a 20 inch barrel for my Spyder sonix from my local gun shop. I figured it would be ... A: Anything over 16 inches is a major waste. You'll also end up getting wierd looks from other people. ... | |
| air | 10/9/2007 |
| Q: im looking to buy a spider VS3 and i was wondering if i would beable to use my CO2 tanks on it or if ... A: you will be able to still use co2 but your shots will not be consistent when shooting strings of ... | |
| repair | 10/9/2007 |
| Q: i just bought a spyder pilot it shot great for a bout 1000 shots but know it wont recock after you ... A: Make sure your bolt and hammer are dry and clean. Also make sure your bottom and upper tube are ... | |
| I am new. | 10/9/2007 |
| Q: Hey. I have got a VL orion and i don't even know how to start or even use is. I just need the step. ... A: The Viewloader orion is a very simple blowback operation often used by many companies such as ... | |
| Scuba Tanks for Paintball | 10/8/2007 |
| Q: I don't have a place i can fill my tanks regularly and well i was wondering, I'm thinking about ... A: you do not need a diving license. You will need to contact a scuba store and ask if somewhere around ... | |
| barrel | 10/2/2007 |
| Q: im going to get the autococker, do you think i will need to upgrade the barrel or will the stock ... A: you'll want to invest on a barrel kit for your autococker, reason being is that since the sutococker ... | |
| elec. frames | 10/1/2007 |
| Q: what do yu mean by electric frames? are those the trigger things that can adjust to auto, 3 ... A: Most trigger frames can only do semi auto but the majority of the new markers out such as Dye, ... | |
| spyder extra | 9/30/2007 |
| Q: i have a spyder extra and it is a semi auto and when i shot it it shoots 2 times in a rouw and does ... A: Make sure the hammer and bottom tube is clean and the tank your using is full. Also make sure you ... | |
| which is better | 9/30/2007 |
| Q: which is better, a spyder sonix or a worr games autococker competition? which has more upgrades? A: I cannot take sides in which is better, they are too completely different guns, one being a closed ... | |
| stock and scope | 9/29/2007 |
| Q: for a spyder sonix, if i want to get a stock, and scope, will i have to get anything for it tp fit ... A: You will not be able to install a sight/scope onto your Sonix without modification. But the point of ... | |
| barrel | 9/27/2007 |
| Q: for my spyder sonix, would a 16" barrel be good for my sonix or would a 14" one be better. a 16" ... A: a barrel is a barrel is a barrel, but anything more than 16" will create drag and make your balls ... | |
| sonix | 9/26/2007 |
| Q: Im getting a spyder sonix 07. is this gun also good for woodsball? is the colour bad for woodsball? ... A: If your playing woodsball you want a dark color like olive drab or black. The sonix is basically ... | |
| halo verse wal-mart | 9/25/2007 |
| Q: i just played sunday and my spyder xtra jammed. the ref suggested i get an electric hoppper at ... A: Yes a forcefeed loader will help you fire more consistently but you will still chop from time to ... | |
| velocity ajustment | 9/21/2007 |
| Q: i have a spyder xtra and i was wondering how to adjust the velocity? also i want a kingman ... A: on your xtra, there is a knob in the back o adjust the velocity. Turn it clockwise to increase the ... | |
| Epiphany | 9/19/2007 |
| Q: What do you think about the smart parts epiphany? Is it worth $300.00? What upgrades do you think ... A: The epiphany is a great gun out of the box. Capable of 17 bps (limited by the board) with some minor ... | |
| Redz Ion | 9/18/2007 |
| Q: What are views on the redz ion. Do you thin it is better than the regular ion. What other guns under ... A: For 150 bucks more than a normal ION, it is a good deal seeing as you will be fitted with Redz ... | |
| air leak issue for mr1 | 9/17/2007 |
| Q: recently my marker has been leaking air. the air sounds like it is coming out of the barrel of it.it ... A: It would have to be a pretty deep scratch seeing ass the valves are stainless steel. Inspect the ... | |
| paintballing | 9/13/2007 |
| Q: i have some land in antigua west indies i think paintballing would go down well but i need to know ... A: If your thinking about starting your own field, be prepared to invest a lot of money, dedication, ... | |
| is it good | 9/10/2007 |
| Q: is this a good paintball gun Spider Aggressor XT A: In all honesty, a good paintball gun would have to be reliable and low maintenance but would have to ... | |
| my spyder electra with eye | 9/3/2007 |
| Q: hey.. will my spyder electra run on a nitrogen tank? and if not what are the effects if i did? A: Yes it will run on nitrogen or N2O (preferably called a HPA (High Pressurized Air) tank). The term ... | |
| 98 C low pressure kit requirements and Qloader | 8/21/2007 |
| Q: What do I need to make my stock 98C shoot compressed air from my HP Compressed Air tank on a low ... A: You don't truly need a regulator for the LP kit. The LP kit is more in favor of keeping your shots ... | |
Paintball
Answers by Expert:
Regis Jung
Top Expert on this page
Expertise
I can answer almost anything in regards to paintball, paintball products, paintball repairs, modifications etc. No, I will not go step by step on how to do certain modifications, only a small summary. If you would like a certain modification done, service, repair or installation done please send your gun(s) to: Impact Paintball 2037 Woodbridge Ave. Edison, NJ 08817 And include a letter of your address and all contact information. We will call you for billing and updates. If you have further inquiries, please call us at (732)339-0820 or email us at impactpaintball@aol.com or join our forum on www.impactpaintball.com Please call or email us before sending your gun so we may know what service is needed. Please before asking me a question, google it first. If you still can't find your answer, then please feel free to ask.
Experience
I am experienced in repair and modification of Autocockers, Egos, Marqs, Ions, Tippmanns, Angels, Shockers, Tiberius guns, Intimidators, Mini's. You name it, I know it.
Organizations
Impact Paintball (No we are not affiliated with Edmonton Impact, we've had the name first [12-13 years])
Education/Credentials
Kean University student and Middlesex County College Student.
Past/Present Clients
Various clients online and store based.
©2012 About.com, a part of The New York Times Company. All rights reserved.