| Subject | Date Asked |
|
| homelite trimmer | 9/26/2008 |
Q: Tom, I have a Homelite Easy Reach model UT20044B.The problem is when I press the primer ...
A: yes, sounds as if a fuel path is obstructed. It should be disassembled, each jet, and path needs to ...
|
| Karcher pressure washer with Honda GCV 160 engine | 9/13/2008 |
Q: Had a plugged jet in the carb took it apart and reassembled it. Carb throat attaches to engine with ...
A: yes you sound correct with the assumption of the needle vale at the float not sealing ...
|
| replacing connecting rod on Troy built chipper/vac with a Tecumseh engine | 9/12/2008 |
Q: I have a Troy built chipper/vac with a Tecumseh engine. Serial number: H50 65582V (B) 3263D. This ...
A: Something did cause this failure, metal fatigue. First off, why on earth would you even attempt this ...
|
| Karcher pressure washer with Honda GCV 160 engine | 9/12/2008 |
Q: Had a plugged jet in the carb took it apart and reassembled it. Carb throat attaches to engine with ...
A: Sometimes it's tough to get everything all back on with only two hands with those Honda's. Has a ...
|
| Briggs 18.5 HP Intek | 9/12/2008 |
Q: I have a Craftsman lawnmower that I just purchased from a friend and he said it was "running rough." ...
A: You could very well be in need of a carb rebuild. A engine running lean on fuel will also run very ...
|
| Lawnboy runs too slow | 9/10/2008 |
Q: I have a 1999 Lawnboy Silver Pro 10323. This is my second such mower and the top speed of the ...
A: Governors seldom go out of adjustment on their own. If you fail to see the choke move during ...
|
| Kohler 26 hp cuts off | 9/10/2008 |
Q: We have a Sears mower with a Kohler 26 hp V-twin motor, model CV730S, Spec no. CV 730-0043. We ...
A: You have the same problem 90% of all consumers have when they try to save money and do carburetor ...
|
| Stalling | 8/30/2008 |
Q: I have a Scott's riding lawnmower, made by John Deere, with a Kohler Command 17.5 hp engine. It has ...
A: Begin by making sure you have a fresh supply of fuel in the tank. Might want to also make sure your ...
|
| Carburetor adjustment | 8/30/2008 |
Q: I have an older Coleman generator that belonged to my father. It sat up for years, but he did drain ...
A: That idle screw is a low idle mixture screw and only effects he engine at a low idle. That is set ...
|
| Why is my Tecumseh 3.5 HP edger engine leaking gas through the air filter? | 8/30/2008 |
Q: "I bought this edger for $30 and I already cleaned out carb thoughly and I found the reason it was ...
A: Sounds as if a carb rebuild is in your near future. You didn't furnish me with the engine model ...
|
| just trying to identify some things | 8/29/2008 |
Q: I have a homemade go kart i just got and i need to do alot of work to get it set up properly and im ...
A: 16 hp?...Going to be one mean little cart. Each one is so different Robert, without knowing the ...
|
| John Deere STX38 | 8/29/2008 |
Q: Before mowing two days ago the tractor would not turn over. I thought that perhaps the battery was ...
A: We live, and we learn....Glad you got it going. Most mowers should warm up a little before putting ...
|
| John Deere STX38 | 8/28/2008 |
Q: Before mowing two days ago the tractor would not turn over. I thought that perhaps the battery was ...
A: I have to be really honest with you, you haven't yet convinced me the battery is ok. First off it ...
|
| John Deere 314, Kohler K321 14 hp | 8/28/2008 |
Q: After running about 10 min. with PTO engaged mowing in moderately heavy grass the engine just stops. ...
A: Your PTO may be in need of replacing, Sounds as if the PTO is maybe slipping, and causing high ...
|
| Powering a PTO clutch | 8/28/2008 |
Q: I have an older Toro Model 30111 commercial grade walk behind mower with a 44" deck and a Toro ...
A: The PTO switch is powered from the ignition switch. But most times it goes to a safety switch first, ...
|
| BS 10A902 won't start | 8/28/2008 |
Q: My mower won't start. I'm not getting any spark when I pull the starter with the plug removed and ...
A: Make sure your safety switch on the side is pulling apart properly when the safety handle is pulled. ...
|
| B&S 445777 24 hp | 8/27/2008 |
Q: I have an engine that has bent push rods on left cylinder as in ...
A: Thats going to depend on how much damage was done to the valve guide hole, it may not hold a guide ...
|
| B&S 20HP timing problem | 8/27/2008 |
Q: My "belly pan" gasket failed and I disassembled the bottom of the motor to replace it. The Mower is ...
A: First thing you need to do is get a repair manual, one should never attempt this type repair without ...
|
| Lawn tractor fuel system problem | 8/27/2008 |
Q: I’m stuck. I have a Craftsman 18.5 HP lawn tractor, Model 917.273643, Engine B&S 31P777-0348-E1. It ...
A: Tell you what, I just have to say with what I read, this problem is in the carb, and or the fuel ...
|
| MTD variable speed drive problem | 8/26/2008 |
Q: I have an MTD Yard Machine lawn tractor model 13AQ670H088 (TMO-314600), SN 1K196H20176 that won't ...
A: Last time I saw that problem was when a customer tried changing their own belt, and misguided it on ...
|
| motor loss of power | 8/26/2008 |
Q: ben, i have john deere 260 riding mower 46inch 3 blade 17hp 1cly kawasaki engine eng# fc540v, ser ...
A: First off 90psi compression is much too low, especially when hot, compression is lowest when the ...
|
| murray riding lawn mower | 8/25/2008 |
Q: eric, i have a 2000 murray riding lawn mower, model 283707 type 1139e1 code 0003152E . i crank and ...
A: Most non-mechanics with all due respect, don't really know how to clean a carb, or where to look for ...
|
| B&S Starter Weak | 8/24/2008 |
Q: My mower engine is 12.5 HP, B&S Model 28U707, Type 1113-E1. The starter won't turn the engine unless ...
A: Two areas to check, is the battery the correct size for the mower, in the stores they will sometimes ...
|
| lawn mower belt adjustment | 8/23/2008 |
Q: I have a Honda HRR 216 self propelled lawn-mower. The belt came off the pulley again and again. I ...
A: Seems those HRP's have a common problem when that belt slips off. After it slips it leaves no ...
|
| carb kit install | 8/23/2008 |
Q: I own a Sears model 917-387240 push mower and would like to rebuild the carburetor. I've bought ...
A: The very very best advice I can give you is to get your hands on Tecumseh manual #695907 it is the ...
|
| Husqvarna riding mower won't start or roll, | 8/22/2008 |
Q: Husqvarna Riding Mower Won't Start or Roll My 2002 Husqvarna riding mower won't start or roll ...
A: Might want to give that brake/clutch switch a good check over due to the fact you had to fiddle with ...
|
| mowers wont run | 8/22/2008 |
Q: Unit 1: Fridgidaire Homeproducts, Mod Q375N22SA Ser 030800M004285. Used this mower most of the ...
A: I would pull a compression test on the mower. I would expect it to be lower due to either a burnt ...
|
| John Deere self propelled lawnmower JS63 product id No. GXJS63V131117 | 8/22/2008 |
Q: The mower at present cuts but will not drive. I have replaced thedrive belt and the clutch cable. ...
A: Before I go replacing a drive train on that I'd be checking the spring that puts tension on the gear ...
|
| Yardking lawn mower. 5.5 HP Honda OHC engine. Runs only with choke on | 8/22/2008 |
Q: I was mowing yesterday and my mower all of a sudden stalled. I pulled the cord and it started, but ...
A: There should also be some main jets, usually brass in color. Sometimes it is the bolt that holds the ...
|
| B&S 18.5 HP/OHV Wont Start? | 8/21/2008 |
Q: Good Evening, Murray Select Model # 425600X8A B&S Engine #s Model - 31D777 Type - 0235E103 Code - ...
A: Ok, first things first, get to your chair it's time for class.......let's begin with some basic ...
|
| Craftsman Connecting Rod Spec | 8/21/2008 |
Q: I am working on a craftsman lawn tractor model 917-271-660 and it sounds like it is knocking ...
A: I'll have to check in my spec manuals at work tomorrow I'm ay home now and do not have that ...
|
| no fire | 8/20/2008 |
Q: I have a john deer model lx178 while mowing the lawn i lost spark I have replaced the igniter and ...
A: Chances are what you need is the "Time off relay"...It holds back the voltage from the coil at timed ...
|
| Husqvarna riding mower won't start or roll, | 8/19/2008 |
Q: Husqvarna Riding Mower Won't Start or Roll My 2002 Husqvarna riding mower won't start or roll ...
A: It really sounds to be like a safety switch, other than the seat switch, there is a clutch switch, ...
|
| Why is my Tecumseh 3.5 HP edger engine not running well? | 8/19/2008 |
Q: I've cleaned the entire engine except the crankcase, i've put clean gas in, and yet my engine will ...
A: from what I saw on your video we can determine it has a good spark, and good compression. it the ...
|
| Craftsman Connecting Rod Spec | 8/19/2008 |
Q: I am working on a craftsman lawn tractor model 917-271-660 and it sounds like it is knocking ...
A: With what you have given me I have no clue what engine make, model, type number or anything else, as ...
|
| Ryobi gas trimmer | 8/19/2008 |
Q: In have Ryobi 825R gas trimmer. The trimmer at first would start fine. After it was warmed up I ...
A: Make sure the spark arrest screen behind the muffler is clean, and not blocked, that's VERY common ...
|
| briggs and startoon 300 series | 8/19/2008 |
Q: I have a similiar problem to this one , asked on 7/18. The mower acts like it is flooded, yet there ...
A: My first question is, has anyone messed with the springs, they should always stay where they were ...
|
| Yardking lawn mower. 5.5 HP Honda OHC engine. Runs only with choke on | 8/18/2008 |
Q: I was mowing yesterday and my mower all of a sudden stalled. I pulled the cord and it started, but ...
A: Well lets give this some thought. Does the choke being on change anything with the spark? No Does ...
|
| torque specs | 8/18/2008 |
Q: i bought a three year old lawn tractor from a neighbour.she ran it dry of oil. i cleaned everything ...
A: Connecting rod torque 150 in. lbs Head bolts 220 in. lbs Intake valve .003 Exhaust valve .005 Not ...
|
| Honda Mower Engine | 8/18/2008 |
Q: my HRX217HXA mower with a GCV190 engine would not start yesterday. The engine would make ...
A: Any chance it was left where rain could have got into the tank? Sounds like water in the tank to me. ...
|
| John Deere Lawn Mower | 8/16/2008 |
Q: I just bought a John Deere riding lawn mower but dont know what year it is, is there a way to find ...
A: Model and serial number on a John Deere should be located under the seat either on the bottom or the ...
|
| specs for carb | 8/15/2008 |
Q: b&s 6hp intek ohv pressure washer bebuilt carb need specs for float needle valve
A: I don't believe that model has a adjustable float, I'm thinking it's the plastic type. If it happens ...
|
| small engine problem | 8/15/2008 |
Q: 3.5 Briggs model 91232 type 0061 01 code 93081903 compression 90. The engine is on a go kart. It ...
A: You will need to remove the carburetor, and separate it from the gas take, make sure all internal ...
|
| 16 HP Vanguard B&S Blowing Smoke | 8/14/2008 |
Q: Resulting in it blowing smoke. The Head Gasket has been replaced which made no difference. Would it ...
A: Scott, sometimes these type of diagnostics is difficult with the home owner type repair person. You ...
|
| Craftsman LT4000 | 8/14/2008 |
Q: I have a craftsman LT4000 (917.252540) lawn tractor that the belt has loosened up on. Any idea how ...
A: belts just don't loosen up, there is always a reason why. Either the belt has stretched. Or a ...
|
| Ferris 22hp kohler 1/2 power | 8/14/2008 |
Q: I Have a 1995 Ferris 60" 22hp model CV22S and it seems like it's working on 1 cylinder. It bogs ...
A: Seems the 2nd cylinder is flooding out. You said you saw a spark at the 2nd cylinder, is it a good ...
|
| 2003 42-inch cut Muray Riding Mower | 8/14/2008 |
Q: The drive belt broke on my lawnmower. I have a new belt but have no idea how to put it on. This ...
A: neither do I, There are somewhere in the area of maybe 500+ Murray mowers out being used today, with ...
|
| Murray 46", 16hp, Hydrostatic | 8/14/2008 |
Q: I cannot find the model # on this mower as I bought it used and the labels are hidden or missing. ...
A: usually we see very few with the fluid levels on the low side. One thing I have found a few times ...
|
| craftsman15.5hpohv riding mower | 8/12/2008 |
Q: how do I install the serpentine belt on this model. I seem to have miss placed the manual.
A: As stated you MUST provide me with the model number, and the serial number of the Craftsman mower. ...
|
| Murray 17hp Lawn tractor | 8/11/2008 |
Q: I just got a Murray 17hp 42" model # 42504x99A. Tecumseh OHV17 engine. It has had gas and oil etc ...
A: You may think that carb is clean as a whistle, until you can see into the small passages, and fuel ...
|
| Briggs carb | 8/11/2008 |
Q: David,,hope you can help. This is a Briggs engine 10A902.I replaced the gasket and the diaphragm and ...
A: Have you checked, and cleaned the pick-u tube screen very well, as well as the metal main jet screen ...
|
| Sears Tiller | 8/11/2008 |
Q: I have an old Sears Tiller model 917.298160 S/N 0805W03057 which I have not used in years. Who made ...
A: It is either one of two manufacturers either Briggs & Stratton, or Tecumseh, Sears used both, if you ...
|
| wiring for new engine on Snapper | 8/10/2008 |
Q: I am stuck and confused while the grass is growing higher. I have good mechanical skills but am ...
A: The fuel shut-off situation is an easy one. It operates with the key switch. Power on when the key ...
|
| now string broken | 8/10/2008 |
Q: i asked about a trottle cable for a Murray 6 hp model 225111x92c. I got the cable on, thanks by the ...
A: Frank, they are a pain i the butt to do if your not familiar with them, there are usually rivets to ...
|
| PUSH MOWER model #: 205310X99A | 8/10/2008 |
Q: I have this push mower that the blade does not spin freely adn a lot of smoke is blowing. Has the ...
A: Juan this is a hard question to answer over the internet, I have no clue what type mower it is, what ...
|
| replacing trottle cable for push mower | 8/9/2008 |
Q: i have a Murray 6 hp model 225111x92c . I recently purchased a throttle cable to replace the ...
A: The round shaped plastic piece has a tab on each side of it, press them together and the piece slips ...
|
| Lawn boy 8461 - gas leak thru valve | 8/9/2008 |
Q: Tom, Lawn Boy mower 2 cycle model 8461 (built in 1987) has started leaking gas when not in use. It ...
A: I would check my fuel line from the carb to the tank for any dry rot. After that assuming there are ...
|
| sears lawn tractor | 8/9/2008 |
Q: i have a sears lawn tractor model 917272050 with a kohler 16hp engine.the governor bolt came loose ...
A: I can not answer specific detailed questions pertaining to individual engines, without a proper ...
|
| B&S engine knock | 8/8/2008 |
Q: I have a 6.5 B&S Intec OHV engine that knocks when you crank it. Once up to speed it seems OK and ...
A: Well, when you take something spinning at somewhere between 2500-3000 rpm's and suddenly stop it ...
|
| replacing starter rope on scott's 5hp europa walk behind lawnmower | 8/8/2008 |
Q: I can seem to get the metal shroud off to get the wheel mechanism it is on with rivets i believe ...
A: yes there are rivets mounted on the pull start at the factory, You must take a drill bit and drill ...
|
| Engine won't turn over when hot. | 8/7/2008 |
Q: Briggs lawnmower engine, 16.5 HP, Model 42A707, Type 2238-E1, starts when cold, but won't turn over ...
A: There is a compression release system inside the motor that helps starting by releasing compression, ...
|
| no fire on lawnmower engine | 8/7/2008 |
Q: I have a Yardman push mower with a Tecumseh engine...model - 11A-573E452 1699466.....serial - ...
A: Terry, have you tried it with the small wire off the coil , this wire is for any safety devices. Any ...
|
| 322 front pto clutch adjustment | 8/6/2008 |
Q: Ben, Based on your reply's this should be a chip shot: John Deere 322 engine model 3tg66uc 3 Cyl ...
A: Ben shifted this question to the question pool, and I picked it up. When I adjust them I tighten ...
|
| Homelite vac attack 2 run problems | 8/6/2008 |
Q: My problem is that the blower will start, but will not pick up any power once the choke goes off. As ...
A: It may very well only have 5 hrs use on it, but it is 2 1/2 yrs old, and fuel begins to turn with ...
|
| Hard starting Honda GX340 | 8/5/2008 |
Q: My Honda GX340 pressure washer "Excel 1990" is hard to start. I used it the other day with no ...
A: This engine is equipped with a compression release, if it fails to operate correctly it will be hard ...
|
| kohler 17.5 hp commander | 8/5/2008 |
Q: its 5 yrs old in a john deere L110 tractor, wife put 2cycle in the tank,,not a biggy it just smoked ...
A: Almost seems you are experiencing two problems at the same time. First off most mowers once started ...
|
| MTD riding tractor | 8/5/2008 |
Q: Whats wrong with the tractor when it rides smooth in reverse but when iam going foward it rides ...
A: I'm just confused as to why it occurs just once in awhile. My suggestion to you is checking the ...
|
| Homelite vac attack 2 run problems | 8/5/2008 |
Q: My problem is that the blower will start, but will not pick up any power once the choke goes off. As ...
A: After checking the obvious like, the spark plug,air filter, and fuel supply, you will want to check ...
|
| Honda WT20X 5.5HP engine. | 8/4/2008 |
Q: My Honda engine just got a new carb and runs great, but when I try to Rev it to full RPMs it just ...
A: Before you go messing with the governor let me ask you, did it have this same low idle before the ...
|
| Removing B & S flywheel | 8/4/2008 |
Q: On my Craftsman riding mower, I have a Briggs & Stratton OHV 17hp model #311707 type #0132. Part of ...
A: 19203 is the Briggs & Stratton part number for the flywheel puller recommended for this engine. This ...
|
| Ranch King won't start | 8/4/2008 |
Q: My dad's Ranch King model # 168971which is 18.5 HP and a 46" cut will not start. It was running ...
A: Is the mower in reverse by any chance? Or are the blades still engaged? Check the seat safety ...
|
| MTD riding tractor | 8/3/2008 |
Q: Whats wrong with the tractor when it rides smooth in reverse but when iam going foward it rides ...
A: You have failed to furnish me with the required model, and type numbers required for me to answer ...
|
| no fire | 8/3/2008 |
Q: Tom, I am a contractor that ownes several loaders and trucks and am able to keep them all running ...
A: Greg, as long as all safety switches are working properly then I believe your in need of a coil. All ...
|
| Scotts Mower L1742 doesnt start | 8/2/2008 |
Q: I have a scotts lawn mower model L1742. engine info model - 31F707 type - 0112 E1 code - 0204012A. ...
A: Might want to check the flywheel key, it may be sheared or partially sheared. As long as you have a ...
|
| Echo PB-403T won't start | 8/2/2008 |
Q: I have an Echo PB-403T and I can not get it to start.I have replaced the Coil, spark plug, and fuel ...
A: Numerous conditions may cause this problem. Spark plug, incorrect fuel mixture, poor gas quality, ...
|
| Reversed throttle? | 8/2/2008 |
Q: I just changed the gas and cleaned the carburetor of a mower I inherited. It had sat in storage for ...
A: Eliza, turtle does in fact mean slowwwww, rabbit is fast. You said something about reassembly, what ...
|
| john deere L110 kohler 17.5 hp cv491s 27509 | 8/2/2008 |
Q: My mower runs, but hard and sometimes misfiring. It almost sounds to fire too soon, but I do not ...
A: yes the flywheel key way can be partially sheared causing the mower to be slightly out of timing. My ...
|
| Ferris 22hp kohler 1/2 power | 8/2/2008 |
Q: I Have a 1995 Ferris 60" 22hp model CV22S and it seems like it's working on 1 cylinder. It bogs ...
A: First check for a spark at each cylinder, are they both getting a strong blue spark? Are both spark ...
|
| Kohler 17.5 hp running hard in john deere L110 rider | 8/1/2008 |
Q: Is there any way to adjust the advance before tdc? It appears there is a magneto pickup that is ...
A: No this timing system is a fixed system. It never needs adjusting. If you give me more detailed ...
|
| Craftsman Lawn mower #900370510 | 8/1/2008 |
Q: http://www.searspartsdirect.com/partsdirect/retrieveModelActionHome!retrie ...
A: I do believe this model can be adjusted to pull the flywheel brake stop, and kill switch back ...
|
| homelite trimmer 25cc 5hcps0254af / ut20044b | 8/1/2008 |
Q: after starting the trimmer it will run approx. 5 min. then sputter out. If i go back thru the ...
A: Numerous conditions may cause this problem. Spark plug, incorrect fuel mixture, poor gas quality, ...
|
| murray riding mower | 8/1/2008 |
Q: I started my mdl 40507x8a about 10-12 year old rider, tonight and it turned right over, but made an ...
A: Ok I need some more info Andrew, when you say it was smoking while in neutral, was the engine itself ...
|
| 17.5 Briggs OHV loss of power | 7/31/2008 |
Q: I've got a Murray w/ a 17.5 B&S OHV motor. 31C707 Type 175E1. Idles great. Take it up to power ...
A: The very first thing that comes to mind is either the governor is failing, or something was ...
|
| yard works lawnmower | 7/31/2008 |
Q: I got a Yard Works lawnmower from the neighbor (model 60-1767-6). He took out the battery. I bought ...
A: Follow the 2 heavy cables, the one going to the frame is your ground, it needs to be connected to ...
|
| Tecumseh won't run right | 7/31/2008 |
Q: I have a WeedEater 42 inch riding mower, purchased around 2000. It was used very little for a year ...
A: First off, does this model carb have a electrical fuel solenoid on the carb bowl? This shuts down ...
|
| No fuel | 7/31/2008 |
Q: Tom, I have an Ariens Zoom 1640 with a Briggs 16 HP Intek engine. It started, ran fine for a few ...
A: i do stand corrected on the fuel pump, it is then a Nikki carb which does have one. I was looking at ...
|
| John Deere L111A is getting difficlut to start up | 7/31/2008 |
Q: I have a John Deere L111A lawn mower for 3 years. Early this year, the engine couldn't be started up ...
A: You first have to determine if it's problem is in one of the 3 areas, Fuel system, ignition system, ...
|
| J deere | 7/31/2008 |
Q: I have a John Deere 42" with a 17.5 Kohler, model CV461S, spec PS-27509, s/n 3205304383. The fuel ...
A: I would check the voltage regulator, it could be at fault casing the system to be over charging, ...
|
| fuel pressurizes with primer bulb | 7/30/2008 |
Q: I have an 18" Craftsman chain saw (358.350180). When I try to prime the saw, the fuel tank ...
A: I would check the inlet in the carb where the primer sends the fuel into the Carb. Sounds as if it ...
|
| Briggs v- twin 20 HP I/C Intek | 7/30/2008 |
Q: I got a john Deere l120 from someone with a blown engine so i got a used replacement. well it runs ...
A: Question , is the spring, and linkage rod for the governor in the correct location? If it is, and ...
|
| Troy-Bilt mower engine trouble | 7/30/2008 |
Q: My Troy-Bilt mower with Briggs & Stratton engine model no. 311777, type 0120-e1 runs fine until it ...
A: Yes the coil could very well be breaking down, they are more prone to when hot. The windings and ...
|
| Tecumseh Carburator problem | 7/30/2008 |
Q: I have a 15 year old Sears Mower Mod 917373680 S/N 081993M269977, 5.3 HP. It has a float carb, with ...
A: Doug, provided you have a good fuel supply to the carburetor, then your in need of a crab rebuild. ...
|
| MTD will not turn over with ignition switch | 7/30/2008 |
Q: Here is the mower. Yardman (MTD) 42" 17.5 horse engine Model Number 13A6695G118.First the engine ...
A: Have you checked all of your safety switches on this model? I suspect your getting no spark across ...
|
| correct sparkplug gap | 7/25/2008 |
Q: I have a Lawnboy Model#7266 the 1977 version and was wandering how to determine the correct ...
A: I tried looking it up using 3 different sources, But seems there can be 6 different engines used on ...
|
| leaf blowers | 7/25/2008 |
Q: i have a mcculloch leaf blower, it has an run and off switch, sometimes it fails to turn off the ...
A: Yes it certainly can. It will cut off your spark, and ground it out, the same way it shuts it off. ...
|
| air and fuel filter | 7/25/2008 |
Q: Where do I find the model and serial number for my swisher 44" trailmower. And where can I purchase ...
A: To find the correct parts you'll need to identify the engine manufacturer. As well as it's correct ...
|
| Serviced Echo SRM 2100 and now Won't Start | 7/25/2008 |
Q: Just serviced my Echo SRM 2100 by replacing broken primer bulb, new air filter and fuel filter and ...
A: You could have pinched the diaphragm under the primer bulb mounting block, or repositioned it. Or ...
|
| Sears LT1000 tractor problem | 7/24/2008 |
Q: I have a sears craftsman LT1000. It has a Brigs vtwin 20hp intek single carb. When the blades are ...
A: Have you checked for a good spark at the cylinder that has the wet plug? The carb sends an even ...
|
| Cutting Deck for Murray 125/102 40303x51 | 7/24/2008 |
Q: I have a Murray 125/102, model number 40303x51, i am looking to purchase another cutting deck. I do ...
A: What you didn't mention is if your looking to purchase a new, or used deck. Murray a few years ago ...
|
| oil pressure | 7/24/2008 |
Q: Just a follow up comment on the oil pressure reading i have on my craftsman DLS/3500 with A 1 CYL. ...
A: Ken, you also have to keep in mind, the reading Briggs gave me is right in the middle of your low ...
|
| Briggs & Stratton : 31C707-0154-E1 won't run | 7/24/2008 |
Q: pulling flywheel on Briggs & Stratton : 31C707-0154-E1 is there a keyway have gas and spark but no ...
A: yes my friend there is a shear key between the flywheel and crankshaft. BUT, this sounds to me to be ...
|
| ariens snowblower | 7/23/2008 |
Q: Ariens ST 1032 snowblower, model 924052, serial 003105, engine is a 10 hp HM100, 159024C, serial ...
A: I'm just getting though a 9 day heat wave and your thinking snow :) Rule number 1, anytime you ...
|
| john deere 185 | 7/23/2008 |
Q: the deck is missing a part for height adjustment was wondering if some one has a diagram of the ...
A: http://jdpc.deere.com/jdpc/servlet/com.deere.u90490.partscatalog.view.servlets.HomePageServlet_Alt ...
|
| No fuel | 7/23/2008 |
Q: Tom, I have an Ariens Zoom 1640 with a Briggs 16 HP Intek engine. It started, ran fine for a few ...
A: Not sure what your referring to as a pick up tube. The only reference to pick-up tubes are with the ...
|
| Self propelled Craftsman mower | 7/22/2008 |
Q: I have a 5.5 year old 6.5 HP self propelled Craftsman walk behind mower. This model has the large ...
A: I have to have the Craftsman model number to know the type of mower style to help. Otherwise, you ...
|
| lawnmower spark plugs | 7/22/2008 |
Q: What type of spark plug do i need for a Dynamark 3.5 -DY750 - 581924 19.5inch blade lawnmower. ...
A: Ms. Susan, two different engine manufactures made engines for this mower. One is Briggs & Stratton, ...
|
| Lawn Mower Explosion | 7/22/2008 |
Q: The mower is a 60in Toro-bilt zero turn riding mower. My cousin had mowed the yard with it and was ...
A: First off allow me to extend my most deepest sympathy. I was certainly overwhelmed by the question. ...
|
| oil pressure | 7/22/2008 |
Q: following up some questions previously asked ; my craftsman rider has 4 hours since new .i plan on ...
A: Ken I'm not real sure of the oil pressure on that model, I'll have to check that out and get back to ...
|
| eagle 1 engine leaks fuel out the air filter | 7/21/2008 |
Q: I have a craftsman 6.75 hp lawnmower with an eagle1 engine. Model number 917.377690. After I use ...
A: Would have to be a faulty float needle and seat in the carburetor. When the level of fuel reaches a ...
|
| B&S 14.5hp OHV I/C mower hard to start | 7/20/2008 |
Q: My B&S is hard to start and getting harder each time,I usually spend about an hour playing with ...
A: The solenoid is smoking due to high resistance. The underlying reason could be many. With the spark ...
|
| Deere STX 38 Hydro - no go! | 7/20/2008 |
Q: Tom- My STX 38 Hydro (black deck) stopped moving (no forward momentum) while I was cutting the lawn. ...
A: I have to be real honest with you Rob, it's not that they can't, it's rather they don't want to. ...
|
| repair homelite line trimmer | 7/20/2008 |
Q: I am trying to repair a Homelite line trimmer engine. It has on the tag: UC No. 20544C and Ser.No. ...
A: Ok lets think this over. When you removed the plug to test for spark you stated, "with the plug held ...
|
| Please help, MTD mower will not start | 7/19/2008 |
Q: All your help will be greatly appreciated. I have a MTD yard machine with a 18 horsepower Briggs and ...
A: But the million dollar question is: What happens when you cross over the solenoid? Try running a ...
|
| Honda riding mower problems | 7/19/2008 |
Q: Hey, I had a question about a Honda HT3813 2-cylinder liquid cooled riding mower I am fixing. I ...
A: They will run even with no battery once jumped. Sounds like your carburetor is gummed up and needs a ...
|
| poulan riding mower | 7/19/2008 |
Q: my husband replaced starter and battery. because it would not start it tries to turn over but it ...
A: Sounds to me to be in the compression release system. As the piston moves up and down among the ...
|
| Toro 8-25 70041 | 7/18/2008 |
Q: I just bought this mower on craigslist in great shape except for a bad diff. I tore it apart and ...
A: Matt, I looked at the diagram for that model. I just see the single bolt, but their diagram isn't ...
|
| Mower Gas Leak from air Primer | 7/18/2008 |
Q: I have craftman rotary lawn mower 6.5 Hp Model#917.388510. I last used it last summer and today when ...
A: Trish, one of two problems, either your primer bulb has dry rotted and now needs replacing, or the ...
|
| Kohler oil consumption | 7/18/2008 |
Q: My father have a CV15 OHV Kohler verticle shaft engine in a toro lawn tractor eight years old with ...
A: Check to see if the breather element or tube is blocked going to the carburetor. I'm not sure why it ...
|
| Weed Eater Lawn Mower Boggs Down | 7/18/2008 |
Q: I've a fairly new Weed Eater brand , Briggs & Stratton 500 series, 158cc lawnmower. It will bogg ...
A: Well first off it's not choking out, if it was you'd be aiding it by priming it Keith. Next time it ...
|
| John Deere 345 Charging/Battery problem | 7/17/2008 |
Q: I have the Kawasaki 20HP liquid cooled twin engine in this, and for a couple years now, the battery ...
A: I have to admit charging systems are not my strong suit. But in most 12v systems 13.2 is borderline. ...
|
| Toro 8-25 70041 | 7/17/2008 |
Q: I just bought this mower on craigslist in great shape except for a bad diff. I tore it apart and ...
A: I wouldn't think so, just clean your casing out very good to remove any metal chips or such. Check ...
|
| Briggs and Stratton 300 148cc | 7/17/2008 |
Q: The little springs conecting the links on the side of the carburator have come off. Can I get a ...
A: If you furnish me with the Model#, and the type # I will take a picture of one and email you ...
|
| not getting fuel from carb to engine | 7/16/2008 |
Q: I have a tecumseh 16.5 engine on my lawn mower. the model # is ohv 165. It will run ffor a few ...
A: Jeff, the big million dollar question , is the carb getting a fuel supply from the filter, or the ...
|
| Briggs & Stratton Carburetor | 7/16/2008 |
Q: I have gas getting into the crankcase. I have rebuilt the carb but still get flooding mainly when ...
A: I can help you after I did some research but, it's rather complicated...send me your email address, ...
|
| Engine stops running after 30 minutes or so | 7/16/2008 |
Q: Tom, I have a riding mower with a 23 hp Briggs & Stratton Intek V-Twin engine. Runs for 30 minutes ...
A: Sounds like your right about the over heating issue. Have you checked all your cooling fins for ...
|
| Shindaiwa Blower 8510RT | 7/15/2008 |
Q: I tried to change the spark plug in my blower, when it was working, and accidentally broke the spark ...
A: You can purchase at a local small engine dealer a repair kit for the broken spark plug wire, it runs ...
|
| kohler fuel pump | 7/15/2008 |
Q: I have a 1983 model Kosher rv genset (3.5CM21-RV) powered by a K181QS Kohler motor. It has a Facet ...
A: Gary, I am not sure of the exact pressure of this particular pump without some time tracing down ...
|
| Home Lite trimmer | 7/15/2008 |
Q: I had just recently got this trimmer from a friend. So I put my oil, gas mix at 50.1 gas and 2.6 in ...
A: Tonia, you will need more oil. If the ratio is based on a 50.1 mix, it means 50 parts gas to 1 part ...
|
| tecumseh 143.986000 | 7/15/2008 |
Q: This engine sets on a acraftsman deck, model # 917.387301. I have already replaced the carb. I ...
A: Check to see if your getting a good fuel supply to the Carb. from the tank. Remove the line, is a ...
|
| Yardman mower | 7/15/2008 |
Q: I have a yardman 6.0hp 20-inch cut push mower. It acts like it wants to start but will not. ...
A: In will need additional information. Are you saying the pull start is locked and won't pull out? If ...
|
| Searing for a Diagram | 7/14/2008 |
Q: I am trying to replace the Blade Pulley on my Power Craft riding mower, Model# Ward's TMO36007. I ...
A: http://wssemw.arinet.com/scripts/EmpartISAPI.dll?MF This is the link, then look under deck ...
|
| Engine emits white smoke | 7/14/2008 |
Q: I have a 17 HP Sears lawn Tractor (model # 917.270732) that is approximately 5 years old. It ...
A: Tom, any possibility you could have got some water into either the gas tank or the fuel can you use ...
|
| Home Lite trimmer | 7/14/2008 |
Q: What is the gas & oil mixture ratio for my Homelite trimmer? I cant keep it running but for a second ...
A: yes, of course it could be one of your problems, but, if your using the same mix as in the past I ...
|
| Poulan 335 Pro Chainsaw Carb settings | 7/13/2008 |
Q: I own a Poulan 335 PRO chainsaw. It starts ok, but will stall shortly after starting. I have tried ...
A: It is rare that when the condition you described needs a carb adjustment. Adjustments of the carb ...
|
| Blowing Oil | 7/13/2008 |
Q: Mr. Tom Adinolfi I have a JD lt155 with a Kohler Model CV15S Spec 41594, this motor has always ...
A: James, in order to give you a more detailed answer without just possible causes, I'd need some ...
|
| Yardman throttle adjustment | 7/12/2008 |
Q: I have a Yardman with a Briggs Stratton, 28V707, type 1170E1 with a Walbro carb. I replace the float ...
A: I think it's the gasket for the float bowl bolt. Did you remove the idle screw (one with the spring ...
|
| Kohler CV16S, engine won't turn over intermittently | 7/12/2008 |
Q: First of all thank you for your time! I have a Kohler engine on my simplicity broadmoor garden ...
A: These bigger engines usually require what is call a compression release to aid in starting. I am ...
|
| how do I use the multi meter to check the pTO ground? | 7/12/2008 |
Q: I have a Craftsman model 917.272260 tractor with a 25 Horse Briggs Intek engine. The blades stopped ...
A: Considering all fuses are good, and there is no visual signs of wire damage. Do you hear the PTO ...
|
| Toro mower engine (old GTS 5) with mikuni carb | 7/11/2008 |
Q: The mower was unused for 2 years, properly stored, and when I attempted to start the engine, it ...
A: The carb seems to be not supplying the right amount of fuel, a passage way is still blocked with ...
|
| Kohler Moter | 7/11/2008 |
Q: Im writing this for my fiance so excuse me if I dont sound like I know what Im talking about. But ...
A: Ok, first off you did very well in explaining, you sounded like a long time mechanic. This motor is ...
|
| my mower will only run wide open | 7/11/2008 |
Q: I just put a new carburetor on my craftsman mower (model number 143.966010 sears)it is a tecumseh. ...
A: This model carb. has no idle adjustment I believe, nor does it have a low idle mixture screw. The ...
|
| B and S 5hp Craftsman tiller | 7/10/2008 |
Q: Had it for 15 years, never any problems till it sat for a year. Now I cant get it to start, but it ...
A: Thats a tough question as to if a novice should attempt a carb rebuild, it depends on the novices ...
|
| Repairing self propel Craftsman lawn mower | 7/10/2008 |
Q: I have a Craftsman 6.75 self propelled model 917.374430. The vari speed cable broke on the end with ...
A: I was unable to find a illustration online myself. I have a few of these in my shop now, if you ...
|
| Kohler M20 leak spark | 7/9/2008 |
Q: The Kohler M20 started running rough when hot last year, so this winter i installed a new coil. Ran ...
A: 120 psi isn't that great actually, the last Kohler I did last week had a lot of hours on it and was ...
|
| Pull Cord for Toro Recycler GTS2 4.5 hp 21" mower | 7/9/2008 |
Q: OK here goes. I snapped the pull cord for my recycler all the way down inside the machine so there ...
A: I sure can, it's a very common problem. From the factory it is riveted in, when it needs repair you ...
|
| mower blade clutch | 7/9/2008 |
Q: Craftsman lawn tractor, model 917.271020. Occasionally the blade clutch will stick with the blades ...
A: Sounds to me as if the tension or idler pulley is not releasing. Messing with the handle won't get ...
|
| Hard Starting | 7/9/2008 |
Q: I have a B&S edger 2.5 hp engine Mod.143571002.Last season no problem starting. This season it would ...
A: Tune up wasn't the problem, you still had carb problems, now please bear with me and take no ...
|
| mtd mower | 7/8/2008 |
Q: i have a 13ag601h729 tractor it started running bad and died i have replaced spark plugs changed oil ...
A: You have a carburetor problem, it is flooding very much. It could be a few things, float needle not ...
|
| toro lawn mower clutch/brake | 7/8/2008 |
Q: i have a toro wheel horse 12-38 xl model #71184 and the clutch/brake is not engaging. how does this ...
A: What exactly is it doing or not doing, is the mower able to move on it's own? Is someone able to ...
|
| B and S 5hp Craftsman tiller | 7/8/2008 |
Q: Had it for 15 years, never any problems till it sat for a year. Now I cant get it to start, but it ...
A: I would bet 20+ years of small engine experience your needing a Carburetor rebuild, especially if it ...
|
| Rectifier | 7/8/2008 |
Q: 1973 Sears Compact E Tractor, 8hp Briggs w/elect start. Mod 190407 Type 0725-01 Code 7203151 Jump ...
A: 391507 is the Briggs number for the rectifier based on the numbers you provided me with. This is in ...
|
| B&S 5hp fun power engine stalls | 7/8/2008 |
Q: I have a 5 hp B&S "fun power" engine on my kiddos' go-kart. It starts with one pull, runs great for ...
A: I believe this is the Briggs engine that the carb mounts on the gas tank, you didn't furnish me with ...
|
| rough idle/run with black smoke | 7/2/2008 |
Q: I have a Troy-built Series 540 Push mower that is about 1 year old. It is now running rough with a ...
A: From what your telling me I would assume your in need of a carburetor rebuild, seems it is running ...
|
| Kohler M20 leak spark | 7/2/2008 |
Q: The Kohler M20 started running rough when hot last year, so this winter i installed a new coil. Ran ...
A: What was the compression in each cylinder? Also I am not familiar with the term "leak spark"...What ...
|
| Ariens LM21S with Briggs and Stratton 6.75 Intek | 7/2/2008 |
Q: I purchased the above unit in 2004 for my mother's modestly sized yard. It worked okay for 2 years ...
A: Ariens to the best of my knowledge stopped producing mowers. But when it comes to snow blowers they ...
|
| Starving for gas | 7/2/2008 |
Q: I have a 2004 Sears Craftsman lawn mower that will stop running like it is starved for gas. ...
A: Ok, sounds like your losing your fuel supply if the filter is empty when this is happening. Two most ...
|
| Lawnmower starting problem | 7/1/2008 |
Q: I have Bolens 4.5 hp Model 12A-264E765 64200 Briggs @ straton engine fairly new i have used maybe ...
A: You need your carburetor rebuilt. Your right it is using the gas from the primer, it comes from a ...
|
| INTEK TROUBLES | 7/1/2008 |
Q: i've got a 6 horse intek on a pressure washer. I work on small engines reguarly but this one is ...
A: The newer Briggs Inteks do not have idle adjustments, or low idle fuel adjustments, your right. Even ...
|
| Gasket set | 7/1/2008 |
Q: I have a 18 hp Briggs & Stratton motor that i am trying to find the gasket set for and am having a ...
A: Here you go Brad, 805049S is the lower crankcase seal PTO side. 842589 is the crankcase, or sump ...
|
| Toro Clutch blade malfunction | 7/1/2008 |
Q: I have a 6.5 hp Toro Super Recycler mower with the clutch style blade Model 20475 Serial 6913394. As ...
A: It most likely is the blade drive belt, they become glazed over after time and begin slipping under ...
|
| Deck belts | 6/30/2008 |
Q: I have a second hand Scotts lawn tractor, made by Murray, that needs both the primary and the ...
A: 037X66MA Belt (replaces 710216) 037X89MA Blade Drive Belt 97 46 Lt (replaces 710217) I believe these ...
|
| Murray riding mower made loud pop then will not turn over | 6/30/2008 |
Q: My wife was cutting the grass today and all of the sudden the mower made a loud pop and died. After ...
A: A clicking sound is usually a bad connection, not sure why that keeps corroding either after either ...
|
| honda push mower | 6/30/2008 |
Q: i have a honda harmony hrb 215 push mower it is making a knocking noise sounds like it is coming ...
A: A noise is a hard thing to diagnose on here, with out hearing it myself, knocking type hollow ...
|
| crafstaman 5.5hp lawnmower starting problem | 6/30/2008 |
Q: My lawnmower was working great until i tilted it to side at around 90 degree to change the blade and ...
A: yes if the blade is loose or off a mower it can do as you stated. It needs the even balance to run ...
|
| BRIGGS 22HP V-TWIN INTEK MOD. 407777 | 6/30/2008 |
Q: I HAVE A HUSKEE PRO GT 22/50. THIS PAST SEASON THE ENGINE STARTED MISSING AND PUFFING OUT BLACK AND ...
A: Mike, sound to me it is sucking some oil, have you pulled a compression test in both cylinders? This ...
|
| Craftsman Lawn Tractor starts sporadically | 6/29/2008 |
Q: Tom, I have a Craftsman 18.5 HP, 42 inch mower electric start automatic transmission lawn tractor. ...
A: Sounds as if you have a carb thats flooding the engine. Was the spark plug wet with fuel each time ...
|
| replaced almost everything | 6/29/2008 |
Q: I have a craftsman 6.0 HP, 21" Briggs/Stratton and Tecumseh carb, push mower. Model# 917-388391 Late ...
A: Ok lets back up here, you said "6.0 HP, 21" Briggs/Stratton and Tecumseh carb," If it's a Briggs ...
|
| lx176 stalling problems | 6/29/2008 |
Q: I have an early 90's john deere lx176 w/ 14 hp Kawasaki ohv engine. just recently It started running ...
A: Ok Randy, first off I am not a parts changer. Some guys just start changing parts hoping, and ...
|
| engine on the honda eg 5000 generator | 6/29/2008 |
Q: I BOUGHT A NEW EG 5000 HONDA GENERATOR.IT HAS ABOUT 10-12 HOURS RUNNING TIME. I BOUGHT IT TO USE AT ...
A: To me this is more of a question for Honda's experts at the manufactures level. Unless the muffler ...
|
| Re: Troy Bilt Trimmer Leaking Gas | 6/29/2008 |
Q: Tom, This is a new question because it wouldn't allow me to post another follow-up to the old ...
A: I would feel very strongly the needle and seat in the carburetor is to blame. It is the float ...
|
| JD 116 drive belt adjustment | 6/28/2008 |
Q: My drive belt needs adjusting. It is hard to shift and won't stop when the clutch pedal is pushed in ...
A: If you begin at the pedal and follow the linkage all the way back you should find an adjustment. Now ...
|
| crafstaman 5.5hp lawnmower starting problem | 6/28/2008 |
Q: My lawnmower was working great until i tilted it to side at around 90 degree to change the blade and ...
A: Sound to me as if you tilted it to the air cleaner, or carburetor side. This is a common mistake, in ...
|
| Craftsman Lawn Tractor starts sporadically | 6/28/2008 |
Q: Tom, I have a Craftsman 18.5 HP, 42 inch mower electric start automatic transmission lawn tractor. ...
A: I need a few basics. When you say won't start, will the engine turn over? I am sensing it won't by ...
|
| Briggs and stratton 13.5 | 6/28/2008 |
Q: I have a two year old riding mower with a Briggs and Stratoon 13.5. It will turn over, but it will ...
A: Sid, you could have actually damaged the flywheel shear pin. Hitting the brick might have partially ...
|
| husqvarna riding mower | 6/27/2008 |
Q: my name is nick. i equipment for a farm/garden supply store. today my supervisor asked me to do a ...
A: Only way I know that gas would be in the oil is a bad flooding problem, so much gas in the cylinder ...
|
| 21 hp briggs 407777 | 6/27/2008 |
Q: ive got a craftsman lt 1000 with the briggs 407777 motor on it i had to pull the bottom of the ...
A: Robert, I don't have a picture of that model that shows a assembled governor control. I just have a ...
|
| snapper riding mower blade wont turn freely | 6/27/2008 |
Q: yes i was wondering why my snapper riding mower with a briggs and stratton engine the blade wont ...
A: Please!! Before checking this make sure the spark plug wires are disconnected at the spark plug this ...
|
| Srarting problem | 6/27/2008 |
Q: model 121682 type 0241E1 will not start with air filter on air filter is new. I remove filter mower ...
A: Was this a problem with the old filter too? Any chance you maybe washed the mower and the filter is ...
|
| Troy Bilt Trimmer Leaking Gas | 6/26/2008 |
Q: I have a 2 cycle Troy Bilt trimmer that was dying when I pulled the trigger but ran fine while the ...
A: You very well could have a line in the wrong location, and it would give you this exact problem. If ...
|
| JD345 | 6/25/2008 |
Q: I have a JD345 that will quit running after a couple minutes and will restart within an hour. Fuel ...
A: During the time it will not start you have to narrow down the conditions. 1. Does it have spark at ...
|
| Intek model 31P777 runs ruff | 6/25/2008 |
Q: I have a John Deere rider mower with a Intek 18.5hp, Model 31P777 Type 0367E1 engine. Its 2 Yrs old. ...
A: I would have to suspect the Carburetor. Sounds as if the governor is hunting, because it's not ...
|
| Lawnmower won't start and has oil in carborater | 6/25/2008 |
Q: I have a murray model #24050c, it's an older model that i got from a friend. I try to start it and ...
A: Are you absolutely sure it is oil rather than gas? Gas flooding over that much is much more common. ...
|
| small engines | 6/25/2008 |
Q: i have a yard machine mower with a 4.5 briggs and stratten engine. after i prime it it starts and ...
A: Without a doubt it is starving for gas, it gets a few sprays from the primer which is a different ...
|
| pto clutch bearing | 6/24/2008 |
Q: I have an 1863 Cub Cadet with a bad pto clutch bearing that needs to be replaced. When it failed it ...
A: Pete, I need the correct year, and the correct model number. That model number is coming up as no ...
|
| Intek model 31P777 runs ruff | 6/24/2008 |
Q: I have a John Deere rider mower with a Intek 18.5hp, Model 31P777 Type 0367E1 engine. Its 2 Yrs old. ...
A: Do you notice any smoke during this?..If so is it black?...what did the old spark plug look like, ...
|
| Troy Bilt Trimmer Leaking Gas | 6/24/2008 |
Q: I have a 2 cycle Troy Bilt trimmer that was dying when I pulled the trigger but ran fine while the ...
A: I would say without hesitation the float needle valve is stuck in the open position and allowing the ...
|
| JD 185 won't start | 6/24/2008 |
Q: My JD 185 won't start, it will crank over and try to start and then it will backfire. Occasionally ...
A: I will need more information, which engine is on this model?...Is spark present when this no start ...
|
| Briggs & Stratton surging | 6/23/2008 |
Q: I have a Craftsman riding mower with a B&S 22hp OHV Intek engine that is about 5 years old, well ...
A: Sound as if it's starving for gas. The Carb. needs to be removed, cleaned throughly. making sure all ...
|
| wiring for ignition switch poulan mower | 5/27/2008 |
Q: I am trying to put a new ignition switch on my poulan pb1638lt rider mower. I cannot figure out the ...
A: Even though it is black and white, it should have the colors of the wires abbreviated in the ...
|
