You are here:
| Subject | Date Asked |
| 1997 Toro Model 20449 12F802 won't start | 2/23/2011 |
| Q: John, I am trying to get my Toro Recycler going but it will not start. I am getting gas to the carb ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| 20HP BRIGGS | 2/23/2011 |
| Q: My 20hp briggs 2 cylinder is hard to start i have cleaned the carburater,cleaned the intake, rebuilt ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| Kubota AT70s tiller | 2/23/2011 |
| Q: My AT70s tiller needs a bearing and seal on the tiller shaft. I've found breakdown diagrams on the ... A: >>Usually the Tiller Shaft Seals can be Replaced without Disassembling the Gears. The Breakdown ... | |
| Toro | 2/22/2011 |
| Q: Here is my original"I have a Toro Zero turn, only a couple years old. It has good gas, a new spark ... A: >>From your Description it Sounds like the Carburetor Requires Soaking and Cleaning, the Carburetor ... | |
| L100 | 2/22/2011 |
| Q: i have been given a 2004 L100 that has a blown motor. after pulling apart found that the conrod had ... A: >>Thanks, I Suspected this was a JD Unit but I wanted to be Certain. >>You can View a Breakdown/IPL ... | |
| Peerless Transmission | 2/22/2011 |
| Q: I have a 20HP/46" cut Murray with a H 2000-002B Peerless Silentrac Transaxle. The transmission used ... A: >>Why did you Use Different Viscosity Oils? >>The 80X90 Gear Lube is all that is Called for on this ... | |
| 24 hp Honda | 2/21/2011 |
| Q: Honda 24hp GX670 This engine runs a hyd gear pump. It starts up with pump engaged open loop not much ... A: >>There are Several Possible Causes for this Problem. >>The Governor Arm has Slipped on the Governor ... | |
| Dynamark B&S tiller | 2/21/2011 |
| Q: John, you once answered this question from someone else. "I'm trying to find part for my tiller so ... A: >>You can Use the Site Addys at this Site Addy; http://www.yetmans.mb.ca/antiques.html to Search and ... | |
| Homelite tiller | 2/20/2011 |
| Q: I lost the lever that starts this tiller model # UT60526. most of the web sites offer the start up ... A: >>You can View a Breakdown/IPL at this Site Addy, http://www.emerichsales.com/ and Select Homelite ... | |
| gas/oil leak | 2/20/2011 |
| Q: I finally got my hs50 Tecumseh started.. There is oil/gas coming out of the breather element. I mean ... A: >>The Following is the Correct Torque from My Manuals and was Conformed with Online Specifications ... | |
| Maintenance questions | 2/20/2011 |
| Q: I have an old ezgo gas powered golf cart. What maintenance should I do each spring? I know I need ... A: >>If this Unit is Being use as Designed, then >>Remove and Clean the Battery Terminals and Battery ... | |
| H50 engine on Ariens thrower | 2/19/2011 |
| Q: I have been given an Ariens 10995 two stage thrower with a H50 motor. The motor starts without ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| Poulan pro 295 | 2/19/2011 |
| Q: John, I have a PP295 model Poulan Pro chain saw, I see 4 types listed,type 1,2,3 & 4, how do I ... A: >>Remove the Muffler and Look Inside the Exhaust Port. >>If the Cylinder and Piston are Scoured and ... | |
| Toro CCR2000 Snowblower | 2/19/2011 |
| Q: Please help me fix my otherwise reliable Toro Snowblower before the next big snow fall! It's a Toro ... A: >>You may be Correct as to Trash in the Jet or Restricting the Carburetors Internal Passages. >>This ... | |
| Honda G150 engine | 2/19/2011 |
| Q: I have a Honda G150 engine on one of my rotorvators, after about twenty minuites working it misfires ... A: >>Is the Spark Plug Firing when the Engine Quits? >>The Following is a Basic Instruction File I made ... | |
| Troy Bilt Back Pack Blower TB4BP 4 Cycle gas | 2/19/2011 |
| Q: This unit runs fine at full power for 5-10 minutes. Then it starts to lose power and slowly dies. ... A: >>From your Description it Sounds like the Engine Requires Rings or the Exhaust Port is Restricted ... | |
| toro snowblower | 2/18/2011 |
| Q: spoke with you a few days ago. I have a Toro snowblower model ccr2000 (38186). Not sure if you ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| 1976 TORO SNOWBLOWER | 2/18/2011 |
| Q: I OWN A 1976 TORO SNOWBLOWER WITH A TECUMSEH ENGINE. MODEL NUMBER 000-1833 (826). ENGINE NUMBER ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| John Deere Lawn Tractor doesn't start | 2/18/2011 |
| Q: This question pertains to a John Deere Lawn Tractor LX176. I had starting problems the other day ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Throttle linkage | 2/17/2011 |
| Q: I have a MTD chipper with a 135212 type0140-01 5 hp briggs. I am having problems getting the linkage ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Honda GX 200 | 2/17/2011 |
| Q: I cant get my Honda GX200 engine to start this year. It is on a John Deere pressure washer. I ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Tecumseh Auger | 2/17/2011 |
| Q: I have an auger with a Tecumseh engine, model number tmo49x. When I start the auger it runs at full ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Craftsman 18" 40 cc chainsaw | 2/16/2011 |
| Q: It takes a bit to start the chain saw, but it does start. It idles very high and when I give it gas ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| gas/oil leak | 2/16/2011 |
| Q: I finally got my hs50 Tecumseh started.. There is oil/gas coming out of the breather element. I mean ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| L100 | 2/16/2011 |
| Q: i have been given a 2004 L100 that has a blown motor. after pulling apart found that the conrod had ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Poulan pro 295 | 2/15/2011 |
| Q: John, I have a PP295 model Poulan Pro chain saw, I see 4 types listed,type 1,2,3 & 4, how do I ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| carburator air/fuel adjustment | 2/15/2011 |
| Q: I have a '90 Yamaha golf cart, serial #J55 105069,G2-AF. It runs better when the choke is left out ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| B&S 422707 Compression Release | 2/15/2011 |
| Q: My mother ( 84 ) years old ) has a MTD/Yard Machine garden tractor with a 18 hp Twin/ L head B&S ... A: >>The Following is a Basic Instruction File for Setting the Valve Clearances on Non OHV Engines. If ... | |
| GCV 160 5.5hp ohv honda engine | 2/14/2011 |
| Q: Does the GCV 160 5.5hp ohv honda engine have any adjustment screws? Mine runs nicely while choked, ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| John Deere LA100 | 2/14/2011 |
| Q: I am a recent amputee due to an infection. Is it possible to move the brake peddle from the left ... A: >>There is No Conversion Kit, but I have McGuivered Several Brake Changes like you are Asking about. ... | |
| s/oil leak | 2/13/2011 |
| Q: I finally got my hs50 Tecumseh started.. There is oil/gas coming out of the breather element. I mean ... A: >>This is Usually caused by an Overfilled Crankcase due to; 1- Too Much Oil Added to the Crankcase. ... | |
| snow champ snow blower | 2/13/2011 |
| Q: John, sorry to hijack or glom onto the other question by the other gentlemen, but had a very ... A: >>No Worries. >>You can View a Breakdown of this Unit at this Site Addy; ... | |
| H50 engine on Ariens thrower | 2/13/2011 |
| Q: I have been given an Ariens 10995 two stage thrower with a H50 motor. The motor starts without ... A: >>If you DID NOT Soak the Carburetor Overnight in Cleaner, then the Carburetor can still be the ... | |
| No spark | 2/12/2011 |
| Q: I have a I/C 16hp Briggs & Stratton and cant seem to get a spark.I have tried taking off the spark ... A: >>The Following is a Basic Instruction File I Made for Checking the Coil/Ign Coil/Magnetron/Armature ... | |
| toro snowblower | 2/12/2011 |
| Q: spoke with you a few days ago. I have a Toro snowblower model ccr2000 (38186). Not sure if you ... A: >>No Worries. Your Very Welcome. >>I am here if you have More Questions or Problems. >>Till Next ... | |
| Engine | 2/12/2011 |
| Q: It is the HM80-155310M one. I'm having a hard time finding the engine model number. The number I'm ... A: >>The Numbers HM80-155310M is a Tecumseh Engine Model Number. >>You can View a Breakdown/IPL of ... | |
| toro snowblower | 2/11/2011 |
| Q: spoke with you a few days ago. I have a Toro snowblower model ccr2000 (38186). Not sure if you ... A: >>I Remember the Question and was able to Locate it in the Archives. >>If this Carburetor has a 2pc ... | |
| Toro Snowthrower Spring Traction Disengage | 2/10/2011 |
| Q: I have a Toro Snow Thrower Model 38035 serial # 6001758. The traction control will not disengage. ... A: >>No Worries. It Happens All the Time. >>Follow the Traction Control Lever Linkage to the End. ... | |
| Toro Snowthrower Spring Traction Disengage | 2/10/2011 |
| Q: I have a Toro Snow Thrower Model 38035 serial # 6001758. The traction control will not disengage. ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| tiller will not start | 2/10/2011 |
| Q: Bought a new craftsman 900 series front tine tiller last season--used 4 or 5 times and it started ... A: >>Send me the Model and Type or Spec Numbers Off the Engine and the Unit/Mower Model Numbers, ... | |
| fuel mix on a MTD GE 40 2-stroke engine | 2/9/2011 |
| Q: I have just been given a MTD GE 40 lawn mower which has a Briggs and Statton Engine. I sure it is a ... A: >>All Two Stroke Engines will use a 50 to 1 Ratio using Today's Two Stroke Oils. I once had an Old ... | |
| Toro shear pin to blade | 2/9/2011 |
| Q: toro model 20016 ser# 220328814. Looking for a part number for a replacement shear key for blade ... A: >>Some of the Blade Adapters have the Key Made as a Part of the Blade Adapter. >>If the Blade ... | |
| Honda G65 mag/ coil match | 2/9/2011 |
| Q: Hi I have a g65 with dead ignition and as its an older model can you please advise what other ... A: >>Depending on the Model Number of the Unit it can be a Solid State Ign or a Point and Condensor ... | |
| auger belt size | 2/8/2011 |
| Q: I have a old Sears Craftsman snowblower it is a 10/32 with model number C950-52379-5 what size of ... A: >>Sorry for the Delay. I had to do some Research for this Question. >>The Traction Belt for this ... | |
| Craftsman mini tiller 536.797500 | 2/8/2011 |
| Q: I have a replacement shaft gear. Is there any particular orientation for the gear, or will it work ... A: >>Most Gears have a Certain Way they have to be Installed. >>What Shaft Gear are you Installing? ... | |
| Toro 13-38HXL - Hydrostat | 2/8/2011 |
| Q: I have a older Toro 13-38HXL - Model 71191 / SN 4906102, I believe it uses the 316-0500 Hydro-Gear. ... A: >>From your Description it Sounds like the Center Section (#70250) is Worn and Requires Replacing, ... | |
| gxv120 | 2/7/2011 |
| Q: could you please give the specifications for the valve timing on the gxv120 honda engine as it ... A: >>Instead of Writing these Instructions Down in this E-mail, >>Since this is a Honda, you can Use ... | |
| generator do not start | 2/7/2011 |
| Q: I was welding with a 220 welder for the first time and after 5 min of use, it just cut off it self, ... A: >>No, the Problem is the Push Tube is Bent and Requires Replacing, the Adjustment of the Rocker Arms ... | |
| 42" Troy Bilt Bronco, blows 20 amp fuse | 2/6/2011 |
| Q: Last summer I bought the mower. Early on last summer the mower was running fine then just stopped ... A: >>From your Description it Sounds like the Stator is Bad and Requires Replacing, there is a Bad Wire ... | |
| generator do not start | 2/6/2011 |
| Q: I was welding with a 220 welder for the first time and after 5 min of use, it just cut off it self, ... A: >>If this is an OHV Engine, then it is Possible the Valve Clearances Require Setting or 1 of the ... | |
| Briggs and Stratton Model #280777 | 2/6/2011 |
| Q: JUst bought a used riding mower, no Engine Manual included. Need to know oil capacity and looking ... A: >>To Purchase an Owners or Service/Shop Manual you can use this Site Addy; ... | |
| Snowblower | 2/5/2011 |
| Q: I have an Arien 5520 snowblower and the engine froze. I can not find a replacement engine.any ideas? ... A: >>This is a Standard 5HP Horizontal Shaft Engine (commonly used on Tillers, Walk Behind Blowers and ... | |
| Snowblower | 2/5/2011 |
| Q: I have an Arien 5520 snowblower and the engine froze. I can not find a replacement engine.any ideas? ... A: >>Usually Any OEM (Briggs, Tecumseh, Kohler, ect) will Work as a Replacement Engine as long as the ... | |
| need a pulley | 2/5/2011 |
| Q: I have a jacobsen Imperial 626 snow blower and I needthe drive pulley. It is a double pulley which ... A: >>You can Visit the Jacobsen Site at http://www.jacobsen.com/americas?country=146 . Click on Genuine ... | |
| Craftsman Snowthrower | 2/4/2011 |
| Q: I have a Craftsman 5 hp 24" 2-stage snowthrower model #247.886640 ser nums 31AS615E099/1I101B40613. ... A: >>This is an MTD Unit (Model 31AS615E099) made for Sears (Model 247.886640). >>If Nothing is Binding ... | |
| poulan 2375 | 2/4/2011 |
| Q: i was wanting to know if you could tell me the settings for the 3 carb/air screws on the poulan ... A: >>There are Three (3) Screws on the Older Carburetors that Require Setting to have the Engine Idle ... | |
| engine won't stay running | 2/4/2011 |
| Q: All winter I have been plowing snow with my Toro Wheelhorse 210-5 rider. It has been running great. ... A: >>If the Engine has a Carburetor Solenoid, then Check it First. >>The Following is a Basic ... | |
| Engine model | 2/3/2011 |
| Q: I have an older AMF Dynamark snowblower, with an 8hp engine, and need to know what model engine it ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| John deere 724d snow blower/tecumseh ohsk70-72507b | 2/3/2011 |
| Q: above is the blower model number and the engine model number. ran the engine for about 1 1/2 hours ... A: >>From your Description it Sounds like the Valve Clearances Require Adjusting or the Carburetor ... | |
| MTD Snowflite 319-600 | 2/3/2011 |
| Q: Where can I get a manual for a MTD Snowflite 319-600 on the internet? A: >>Try this Site Addy; http://www.outdoordistributors.com/ . >>They have the Best Selection for ... | |
| Engine model | 2/3/2011 |
| Q: I have an older AMF Dynamark snowblower, with an 8hp engine, and need to know what model engine it ... A: >>From the Picture you Sent, this Engine Looks to be an Older Tecumseh Engine. >>Look on the Engines ... | |
| Transmision Problem On A Craftsman Mower | 2/2/2011 |
| Q: I am working on a Craftsman Tractor model 917.273020 which will move on flat ground but when you ... A: >>Sorry for the Delay. >>I am Waiting for a Response from the OEM about this Transaxle. >>I Can Not ... | |
| Snowblower runs way way too fast | 2/2/2011 |
| Q: I have had a Sears Craftsman Snowblower (Model #C950-52935-0)for the past 5 years or, handed down ... A: >>From your Description it Sounds like the Throttle Linkage to the Carburetor is Binding or is ... | |
| Sears pressure washer | 2/2/2011 |
| Q: Remember me? Tate's Auto Service, retired. John, I have a Pressure washer (Sears 580767200) that ... A: >>Long Time. It's Great to Hear from you again. I Hope All is Well with You and Yours. >>From your ... | |
| Transmision Problem On A Craftsman Mower | 2/1/2011 |
| Q: I am working on a Craftsman Tractor model 917.273020 which will move on flat ground but when you ... A: >>The Sears Breakdown for this Hydro Transaxle is Not Readable to me and the Sears Site does Not ... | |
| toro ccr2000e snow blower | 2/1/2011 |
| Q: my toro will only throw snow with the choke either half or fully on. it ran fine until this past ... A: >>You can Adjsut the Float Heigth by Bending the Tab/Ear on the Flaot that Connects with the Needle ... | |
| auto throttle | 2/1/2011 |
| Q: I have a blackmax generator with honda GX390 13hp gas engine and the wires on the auto throttle ... A: >>Sorry for the Delay. I had to Purchase a New PC and then Switch my Files and Records from the Old ... | |
| Murray snowblower 627804X6 | 2/1/2011 |
| Q: Part #579941E701MA (original part 579941) Assembly Traction level (#190 in the figure)sheared off ... A: >>Sorry for the Delay. I had to Purchase a New PC and then Switch my Files and Records from the Old ... | |
| HONDA HS35 | 2/1/2011 |
| Q: Bridgers, My husband is working on a Honda HS35 snow blower and he has run into some issues. When ... A: >>Sorry for the Delay. I had to Purchase a New PC and then Switch my Files and Records from the Old ... | |
| Auger drive belt replacement | 1/31/2011 |
| Q: I'm trying to remove the auger housing on a Honda HS828 snowblower, model number SZAK10066717 and I ... A: >>Sorry for the Delay. I had to Purchase a New PC and then Switch my Files and Records from the Old ... | |
| Transmision Problem On A Craftsman Mower | 1/31/2011 |
| Q: I am working on a Craftsman Tractor model 917.273020 which will move on flat ground but when you ... A: >>The Biggest Problem with Moving Snow is the Ground Drive Belt Stretches and will Usually cause ... | |
| snow blower engine does't shut off | 1/31/2011 |
| Q: i have a craftsman 8 horsepower, electric start, dual stage snowblower(model 536.881800) with a b&s ... A: >>Hello Ron: >>Sorry for the Delay. I had to Purchase a New PC and then Switch my Files and Records ... | |
| Ust 3500 generator | 1/30/2011 |
| Q: Where do I get my hands on a replacement plastic cover for pull cord start assembly generator is ... A: >>Sorry for the Delay. I had to Purchase a New PC and then Switch my Files and Records from the Old ... | |
| noma G2250000 code 6262 | 1/30/2011 |
| Q: I cant shift...it has 6 forword..2 reverse I cant find info on noma...is there a similar ... A: >>Sorry for the Delay. I had to Purchase a New PC and then Switch my Files and Records from the Old ... | |
| Yardman Riding Mower | 1/30/2011 |
| Q: I have a problem the Yardman Riding Mower I have does not seem to have a neutral. Is this normal? A: >>If the Unit has a Hydrostatic or Hydromatic Transaxle, then it will Act as though it has No ... | |
| toro ccr2000e snow blower | 1/29/2011 |
| Q: my toro will only throw snow with the choke either half or fully on. it ran fine until this past ... A: >>Send me the Model Numbers Off the Unit, Please. With these I can Locate the Proper Manual and ... | |
| toro self propelled | 1/29/2011 |
| Q: my toro mower wont stay running, ive cleaned the carb, replaced the needle, changed the oil, the gas ... A: >>Did you Soak the Carburetor in Cleaning Solution? >>If No, then >>The Carburetor can Still be the ... | |
| 26 hp torque specs | 1/29/2011 |
| Q: I would like to know the torque specs for a Briggs & Stratton 26hp crankcase bolts. A: >>You can use the Engines Model Numbers (usually located on the metal engine cover) and the Chart at ... | |
| Toro Power Clear clutch stuck | 1/28/2011 |
| Q: I just bought a Toro Power Clear 221Q and used it yesterday for the first time to clean up a pretty ... A: >>This Model has a Spring that Returns the Drive to Neutral. >>You can View a Breakdown/IPL of the ... | |
| Toro Power Clear clutch stuck | 1/28/2011 |
| Q: I just bought a Toro Power Clear 221Q and used it yesterday for the first time to clean up a pretty ... A: >>From your Description it Sounds like the Pivot (for the Ground Drive Idler Pulley) has Frozen in ... | |
| Kohler Magnum 12hp fuel pump | 1/28/2011 |
| Q: Good Morning John, I am in the process of starting my own mobile tire business. My father is in the ... A: >>Change the Spring Style Clamps to the Screw Style Hose Clamps. >>Change Any Hoses that are ... | |
| Scotts Riding Mower Deck Belt | 1/27/2011 |
| Q: I have a Scotts Model 2546, made by John Deere, that the blades have stopped engaging. The mower is ... A: >>It is Possible for the Belt to Stretch enough that the Tensioner Pulley will Not Even Attempt to ... | |
| john deere blowwer | 1/27/2011 |
| Q: trying to find points gap specs for japan made 40cc blower A: >>The Points are Gapped to .015in. >>If you Hit a Snag or this Does Not Correct the Problem, I Hope ... | |
| Craftsman Snow Thrower | 1/27/2011 |
| Q: I have a Craftsman Snow Thrower, given to me by my father, who only used it a handful of times, so ... A: >>The Bad thing about Tecumseh Engines is they have a Weak Connecting Rod and when this Engine Sets ... | |
| 1989 toro 521 snowblower | 1/27/2011 |
| Q: I have a 1989 toro 521, when posing the question for repair it is said that the carburetor needs to ... A: >>A Breakdown of the Engine and Carburetor can be Located at Different Sites on the Web. >>The ... | |
| hard to start | 1/26/2011 |
| Q: I have 5hp engine on a go cart. It is very hard to start, but when it does start it runs good and ... A: >>From your Description it Sounds like the Carburetor Requires Soaking and Cleaning and the ... | |
| chainsaw carb settings | 1/26/2011 |
| Q: Craftsman chainsaw 14 in. Model 358.351440. What are the low and high settings on the carb. A: >>The Following is the Instruction File for Setting the Air Mixture Screws. Any Input is ... | |
| Scotts Riding Mower Deck Belt | 1/25/2011 |
| Q: I have a Scotts Model 2546, made by John Deere, that the blades have stopped engaging. The mower is ... A: >>Sorry for the Delay. Snow and Ice have Hit Us hard and I have been Very Busy. >>You can View a ... | |
| CUB CADET WON'T START | 1/25/2011 |
| Q: My Cub Cadet 1050 42" cut wont start.Turn the key with plenty of battery juice,engine starts turning ... A: >>Sorry for the Delay. Snow and Ice have Hit Us hard and I have been Very Busy. >>This is a Common ... | |
| vacuum snout for Troy Bilt model 47279 | 1/25/2011 |
| Q: On 5-14-08 you had a question from Leo about a model 47279. We are looking for a vacuum snout for ... A: >>Sorry for the Delay. Snow and Ice have Hit Us hard and I have been Very Busy. >>Sorry, but I Do ... | |
| noma snow blower | 1/24/2011 |
| Q: I have a problem with the Noma auger and can't locate a manual. I removed the cover, according to ... A: >>Sorry for the Delay. Snow and Ice have Hit Us hard and I have been Very Busy. >>You can View a ... | |
| 82? toro 724 38050 drive train | 1/24/2011 |
| Q: i recently inherited my father in laws 1982 toro 724 38050 snowthrower. i was able to get it ... A: >>Sorry for the Delay. Snow and Ice have Hit Us hard and I have been Very Busy. >>You can View a ... | |
| Simplicity Snowblower | 1/24/2011 |
| Q: I have a Simplicity snowblower, model 643-001393. I believe it was made around 1973. The problem is ... A: >>For some Reason I Did Not Receive the Picture. >>From your Description it Sounds like the ... | |
| Valve springs | 1/23/2011 |
| Q: Briggs-Stratton Engine Model 19402, L-Head. I removed the valves/springs to adjust the valve ... A: >>The Shorter Spring is the Exhaust Spring. >>If you Hit a Snag or this Does Not Correct the ... | |
| Snowblower stalling | 1/23/2011 |
| Q: I've been having a problem with my snowblower (Snapper 7524 with a Briggs & Stratton 7.5 HP engine) ... A: >>Change the Gas. >>If Changing the Gas Does Not Correct the Problem, then >>Soak and Clean the ... | |
| John Deere Snow Thrower Model 320 | 1/23/2011 |
| Q: The engine still works great. However, the blade housing has loosened up and is wobbly. I'm sure ... A: >>You Might be Surprised to Know that the Parts May Still be Avaliable. >>You can View a ... | |
| Snowchief Snowblower | 1/22/2011 |
| Q: John, I need your help. I am trying to locate a drive gear (I think) for a 25" 8HP Snowchief. The ... A: >>General Power Equipment was the Parent Company of Atlas Power Equipment, Lawn Chief, Snow Chief ... | |
| kohler engine repair | 1/22/2011 |
| Q: I want to change the starter on my kohler 16 hp model#mv16qa ; mounted in 1987 walker 54" riding ... A: >>You can View a Breakdown of the Engine at this Site Addy; http://www.kohlerplus.com/login.asp (IE5 ... | |
| Scott Bonnar model 45 series mower 14" | 1/22/2011 |
| Q: My blade has become blunt and it requires to be set& sharpened. I was thinking can the reel be ... A: >>Setting and Sharpening are the Only way to Correct the Cutting Problem. >>The Reel cannot be ... | |
| New thread for 16hp Briggs & Stratton Surging & Dying | 1/21/2011 |
| Q: I wasn't allowed another follow up question from the last thread so I had to start a new thread. ... A: >>No Worries. >>Anything is Possible. >>The Following is an Instruction File I Made for Setting the ... | |
| Leaky carb on Tecumseh HSK 635 | 1/21/2011 |
| Q: 3.25 hp with a Tecumseh HSK 635 motor. Went to clean out the carb this season. Did so, closed it ... A: >>This has become a Major Problem with the Newer Bowl Style Carburetors. >>You can View a ... | |
| Murray snowblower | 1/21/2011 |
| Q: I have a 8 hp Murray snoblower , I rebuilt the carb when I take the plug out and spray it it fires ... A: >>Send me the Make, Model, Type/Service and Code Numbers Off the Engine, Please. With these I can ... | |
| Replace Auger - Craftsman 536881750 | 1/20/2011 |
| Q: Good afternoon Mr. Bridges. I was following your conversation back on 11/02/2008 about how to ... A: >>If you Use the Breakdown at the Sears Site as a Guide to Disassemble and Assemble the Unit, I can ... | |
| kohler engine \no fire | 1/20/2011 |
| Q: I have a kohler commandpro25 no fire engine turns ,How to troubleshoot family 4khxs 7252gc ,model ... A: >>You can View a Breakdown of the Engine at this Site Addy; http://www.kohlerplus.com/login.asp (IE5 ... | |
| fd611v kawasaki engine | 1/20/2011 |
| Q: got a sticking inlet valve on starter side outside of taking engine apart-got any ideas- also how ... A: >>This is an OHV Engine. >>You can Try Marvel Mystery Oil in the Crankcase Oil and Put a Small ... | |
| 16hp Briggs & Stratton runs & then sputters & dies | 1/19/2011 |
| Q: I have a 1642HS John Deere Saber w/ a 16hp Briggs & Stratton Engine. I can start the engine & it ... A: >>I get Bad Ign Coils all the Time, but I Replace Many of these Also. >>You can Purchase a Bad Ign ... | |
| Cub cadet ltx 1046 with 22 HP Kohler® Courage® V-Twin OHV engine not turning over | 1/19/2011 |
| Q: I have less than 20 hours on my new Cub ltx 1046 with the Kohler® Courage® V-Twin OHV engine. The ... A: >>From your Description it Sounds like the Valve Clearances Require Setting (a common problem with ... | |
| Sears Craftsman Snowblower | 1/19/2011 |
| Q: I have a 6yr old, 30", 11 hp Craftsman snow blower, model # 536.888110. I'm trying to find out, 1.) ... A: >>SAE 30 Engine Oil is Suggested and I Use SAE 10W30 Synthetic in All my Equipment (automobiles ... | |
| gator problem | 1/18/2011 |
| Q: I have a 95 6x4 gator. It will start fine, but here is the problem when going uphill on the roadways ... A: >>Gas in the Oil is Usually a Sign that the Head Gasket is Blown between the Push Tube Galley and ... | |
| Toro Powerlite Snow Thrower Model#38170 | 1/18/2011 |
| Q: The unit will not start when cold (temp below 35 or so), unless I prime with carb cleaner down ... A: >>It takes a Minimum of 100PSI for an Engine to Run and Idle Correctly. >>If the Compression is ... | |
| Tecumseh HSK840 8211A Snow King | 1/18/2011 |
| Q: Starter rope is stuck in the machine and won't pull out. Why and what can we do to fix it? (this had ... A: >>You can View a Breakdown/IPL at this Site Addy, http://www.emerichsales.com/ and Select Tecumseh ... | |
| 18.5 intek | 1/18/2011 |
| Q: I have a verticle shaft engine.. Can this be converted to a horizontal shaft application A: >>No. >>Other than Using a Belt and Pulley System to Change the Drive from Horizontial (vertical ... | |
| 16hp Briggs & Stratton runs & then sputters & dies | 1/17/2011 |
| Q: I have a 1642HS John Deere Saber w/ a 16hp Briggs & Stratton Engine. I can start the engine & it ... A: >>The Breakdown for this Unit does Not Show an Igniter or the Control Circuit Board Used, so the ... | |
| Tuff Torq K56 Transmission | 1/17/2011 |
| Q: I have a Simplicity Regent lawn mower with a K56 transmission (not sure if it is K56A or K56B). ... A: >>Are you Sure the Transaxle Drive Belt is Not Slipping? >>Change the Hydraulic Oil and Use 15W40 ... | |
| Toro Powerlite Snow Thrower Model#38170 | 1/17/2011 |
| Q: The unit will not start when cold (temp below 35 or so), unless I prime with carb cleaner down ... A: >>What is the Engines Compression? >>Did you Soak the Carburetor Overnight in Carburetor Cleaner? ... | |
| measurements | 1/17/2011 |
| Q: Can you tell me where I can find the length and size of the output shaft of a Tecumseh motor ... A: >>Sorry for the Delay. >>I am Trying to Locate the Manual that has the Crankshaft Specifications in ... | |
| Snowblower Replacement Belt | 1/16/2011 |
| Q: I have Snapper sx5200e. I need a new belt. I only can find the belt OEM part online, 4-1947. What is ... A: >>The Belt is a 33" X 3/8" Belt. >>If you Hit a Snag or this Does Not Correct the Problem, I Hope ... | |
| poulan 3314 chain saw | 1/16/2011 |
| Q: this chain saw is extremely har to start cold when it does start it only runs for about 2 minutes ... A: >>From your Description it Sounds like a Restricted Exhaust Port/Spark Arrestor Screen, a Damaged ... | |
| 16hp Briggs & Stratton runs & then sputters & dies | 1/16/2011 |
| Q: I have a 1642HS John Deere Saber w/ a 16hp Briggs & Stratton Engine. I can start the engine & it ... A: >>How Long is a Few Minutes? >>As Soon As the Engine Stopps Running, Check the Spark Plug For Fire. ... | |
| Recoil rope mechanism | 1/15/2011 |
| Q: John, I'm also one of the gang here @ All experts over in the electrical dept. I have a ... A: >>You have the Pressed "Spring Pin" that Hold the Plastic Rope Pulley and Other Components Together. ... | |
| Engine won't start | 1/15/2011 |
| Q: I have a Tekumsah HMSK100-159212t engine on an old craftsman snowblower. It won't start. I have ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| Recoil rope mechanism | 1/15/2011 |
| Q: John, I'm also one of the gang here @ All experts over in the electrical dept. I have a ... A: >>The Following is a Basic Horozontal Recoil Starter Repair Instruction File. Any Input/Suggestions ... | |
| John Deere 318 Hydraulic Levers | 1/15/2011 |
| Q: The side hydraulic levers on my John Deere 318 are becoming harder to operate, especially now that ... A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| governor | 1/14/2011 |
| Q: sir i have made a generator with the help of an engine TOYOTA 16 Valve 5A type and a 15Kw three ... A: >>Let me Research This and get Back to You, Please. >>I have a Generator with an Electric Governor. ... | |
| Snowblower | 1/14/2011 |
| Q: It is a 8hp Tecumseh and 25" cut. The problem I'm having is that it won't move forward unless I give ... A: >>From your Description it Sounds like the Worm and Ring Gears in the Transmission are Worn and ... | |
| Craftsman Snow Thrower | 1/14/2011 |
| Q: I have a question about my Craftsman Snow Thrower, MODEL# 53688520000. When I went to push the ... A: >>Thanks for the Information. >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| Snow blower | 1/13/2011 |
| Q: I have a Snow Chief SC 320 that I hit something with and need to take off the impeller to have ... A: >>Usually these Pulleys have an Allen Lock Screw that Holds the Pulley Tight to the Woodruff Key. ... | |
| Reset a John Deere Snowblower recoil spring | 1/13/2011 |
| Q: I have a JD circa 1980's snowblower with a broken pull rope. I got the crank assembly apart and ... A: >>If there is Not an Anchor Hole in the Blower Housing for the Spring to Lock Into, then the Spring ... | |
| Craftsman Snow Thrower | 1/13/2011 |
| Q: I have a question about my Craftsman Snow Thrower, MODEL# 53688520000. When I went to push the ... A: >>Either the Carburetor Needle Valve and Float are Sticking or the Primer Requires Replacing. ... | |
| John Deere 1032 | 1/13/2011 |
| Q: One of the chains keeps popping out. As this machine is nearly 20 years old, can this machine be ... A: >>Yes it can be Repaired. >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| Reset a John Deere Snowblower recoil spring | 1/13/2011 |
| Q: I have a JD circa 1980's snowblower with a broken pull rope. I got the crank assembly apart and ... A: >>The Following is a Basic Horozontal Recoil Starter Repair Instruction File. Any Input/Suggestions ... | |
| Snow blower | 1/12/2011 |
| Q: I have a Snow Chief SC 320 that I hit something with and need to take off the impeller to have ... A: >>The SC 320 is the Series Model. >>Send me the Model Numbers Off the Unit (Unit Model Numbers), ... | |
| Gravely MA210 play in worm drive shaft | 1/12/2011 |
| Q: I have a Gravely MA210 that's been working wonderfully for years. This morning under load (heavy ... A: >>You can View a Breakdown of this Unit at this Site Addy; http://www.gravely.com/ and Select "Parts ... | |
| toro ccr 2000 | 1/12/2011 |
| Q: I was using my blower today and it ran perfect. I hit some deep snow and the engine lost power. It ... A: >>From your Description it Sounds like the Flywheel Key was Damaged when you Hit the Deep Snow. ... | |
| Briggs runs rough when hot | 1/11/2011 |
| Q: Briggs 190402 Type 0696-02 Code 7205101 Starts easily, runs great. After about 10 min. I have to ... A: >>Did you Soak the Carburetor in Cleaning Solution or Did you Use Spray Cleaner to Clean the ... | |
| Toro Snow Blower Paddles | 1/11/2011 |
| Q: How do you change the paddles on a Toro CCR 1000 snowblower? There are some bolts on the outside ... A: Bello Brian: >>This Depends on the Unit Model. >>The CCR1000 is the Series Model. >>Send me the ... | |
| Briggs and Stratton 31H777 engine | 1/11/2011 |
| Q: Ok, my riding mower will not start. I have a video to explain exactly what it is doing. I have had ... A: >>I am Guessing that the Starter was Checked because the Engine was Turning Approximately 3/4 of a ... | |
| Briggs runs rough when hot | 1/11/2011 |
| Q: Briggs 190402 Type 0696-02 Code 7205101 Starts easily, runs great. After about 10 min. I have to ... A: >>If you Suspect the Lines to be Bad, then Yes, Replace them but Use Screw Style Hose Clamps. >>As ... | |
| 021 stihl chainsaw | 1/10/2011 |
| Q: i asked ben but has never repaired a stihl. i took carb to pieces and put back twice. now motor ... A: >>The Carburetor Metering Valve Actuator is Set too Low and is Allowing the Metering Valve to Stay ... | |
| toro ccr2000 leaks gas | 1/10/2011 |
| Q: I have a 1995 occurs (#38180) that leaks gas through the carb when the machine of off. The carb is ... A: >>Are you Sure you Did Not Read some of my Posts on this Problem. LOL. >>You have Done the Correct ... | |
| Briggs runs rough when hot | 1/10/2011 |
| Q: Briggs 190402 Type 0696-02 Code 7205101 Starts easily, runs great. After about 10 min. I have to ... A: >>From the Question, I See that I can Welcome you Back. >>Thanks for Your Comments. >>What are the ... | |
| Craftsman snowblower 6hp B&S won't start | 1/9/2011 |
| Q: Am trying to get neighbors blower running .They left it out all last winter and this summer . Found ... A: >>There are Only 4 Reasons for the Valves Not to Move. 1- >>The Valves are Stuck. 2- >>The Push ... | |
| Clarence's impeller mod - snowblower | 1/9/2011 |
| Q: I have a 10yr old Craftsman snowblower 26" 8hp. I noticed the edges of the impeller blades have ... A: >>Thanks for this Question. >>It Shows Your Concern for the Unit as a Whole. >>I have Installed Many ... | |
| BCS tiller model 720 | 1/9/2011 |
| Q: Last spring I through a rod in my B & S powered BCS tiller and unbolted the 4 bolts expecting to ... A: >>Try this Addy; http://bcsamerica.com/pdfs/720.pdf for an Illustrated Parts List for this Unit. ... | |
| Craftsman snowblower 6hp B&S won't start | 1/8/2011 |
| Q: Am trying to get neighbors blower running .They left it out all last winter and this summer . Found ... A: >>Was the Piston Placed at Top Dead Center when you Adjausted the Valve Clearance? >>Did you Set the ... | |
| stator | 1/8/2011 |
| Q: i have an 11hp in a lt1000 wheel horse.it isnt getting any fire.i have a stator with 1 wire coming ... A: >>The Stator is the Charging Coil used to Charge the Battery and the Armature/Ign Coil is what Fires ... | |
| lawn mower magets and flywheel | 1/8/2011 |
| Q: can you please tell me where the magnetic field and the fkywheel is located on the lawn mover A: >>Remove the Blower Housing (metal engine cover) from the Engine. >>You will then have Access to the ... | |
| transmission problem | 1/7/2011 |
| Q: Scotts by john deere 2046h.Is hard to fix this kind of automatic transmission?I changed the belt but ... A: >>Have you Checked the Fluid Level Yet? >>You can View a Breakdown/IPL of the Engine and Mower at ... | |
| Homelite trimmer fuel supply problem | 1/7/2011 |
| Q: I have a Homelite trimmer model ST175BC. When I received it, it didn't run at all. From previous ... A: >>Look at the Carburetor and Locate the Diaphram Cover Plate that is Held onto the Carburetor with 4 ... | |
| electric chainsaw | 1/6/2011 |
| Q: I am thinking of buying an electric chainsaw. What can you tell me about them. Are they reliable? ... A: >>I am Not Much of a Fan of the Electric Outdoor Lawn and Garden Products. >>We Repair the ... | |
| Cant get 12hp briggs and stratton to run | 1/6/2011 |
| Q: I dismantled my 12hp B@S as the Drive shaft seized on the Sump cover . ( lack of oil ) Internally ... A: >>According to the Numbers this is a Briggs Model 281707, Type 0226-01, Code 90102231 (this Engine ... | |
| Tecumseh OH195SA-72549G | 1/6/2011 |
| Q: This is a sears snow thrower ran great last year put it away added seafoam to the fuel and ran it ... A: >>Usually the Backfiring through the Carburetor is caused by a Blown Head Gasket between the Push ... | |
| B&S 12.5hp not starting | 1/5/2011 |
| Q: The engine turns, but will not start. The conrod broke so I took it apart, replaced the conrod, ... A: >>Thanks for the Picture. >>The End Gap Looks about Normal for a Worn Block with New Rings. >>It ... | |
| Removing the plastic cover on my Honda HS35 Snowblower | 1/5/2011 |
| Q: I went to start my Honda HS35 the other day and the recoil cord came untied and the cord came ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| Briggs & Stratton Ignition Armature Air Gaps | 1/5/2011 |
| Q: Briggs & Stratton Armature Air Gap on my 5hp outboard If I set the gap on the magnet at .12 would it ... A: >>Setting the Coil Closer or Farther Away from the Flywheel Increases and Decreases the Current that ... | |
| gator problem | 1/4/2011 |
| Q: I have a 95 6x4 gator. It will start fine, but here is the problem when going uphill on the roadways ... A: >>Hello Scott: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| Polaris Ranger electrical short. | 1/4/2011 |
| Q: I have a 2006 Polaris Ranger TM. The TM is the model that has the 18hp Robin engine. The only ... A: >>This will Usually Occur when the Stator/Charging Coil Shorts and Requires Replacing. >>For Testing ... | |
| B&S 12.5hp not starting | 1/3/2011 |
| Q: The engine turns, but will not start. The conrod broke so I took it apart, replaced the conrod, ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| Honda GX620 | 1/3/2011 |
| Q: I am working on a Thermal Arc Predator welder powered by a Honda GX620. The engine will not start ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| no spark at all | 1/2/2011 |
| Q: is it possable both coils are shot ,i have isolated the motor totally from all safety switches many ... A: >>Some of these Shut Off Diodes will Read Open Until the Grounded Side (lead of the Diode goes to ... | |
| Honda Generator no fire | 1/2/2011 |
| Q: I have a Honda EU3000IS-EXGF-1175526 generator in the shop that came in with a no-fire condition. ... A: >>Try Mounting the Coil Opposite from the way it is Mounted Now. >>Flip the Coil Over. >>The ... | |
| CRAFTMAN 32CC WEED EATER | 1/2/2011 |
| Q: HOW DO YOU REPLACE THE STARTER ROPE ? THANKS RON A: >>Depending on the Model, it Varies. >>The Following is the Most Common Recoil Starter Rope and ... | |
| Kohler Boat generator | 1/2/2011 |
| Q: My boat has a Kohler 13eozd power generator. Without reason, it starts displaying the UU code (under ... A: >>Hello Luis: >>It is Possible the Brushes are Worn and Require Cleaning. >>Send me the Complete ... | |
| no spark at all | 1/2/2011 |
| Q: is it possable both coils are shot ,i have isolated the motor totally from all safety switches many ... A: >>It is Rare for Both Coil to Go Bad at the Same Time. >>Did you Disconnect the Shut Off Lead/s at ... | |
| Gokart starting | 1/1/2011 |
| Q: I've got a Carter Bros gokart with the Tecumseh zs168fb (196cc/6.5hp) engine. I'm thinking one of ... A: >>This is an Engine that has Just Started Showing up in the Shop within the Past 4 or 5 Months. >>I ... | |
| Gokart starting | 1/1/2011 |
| Q: I've got a Carter Bros gokart with the Tecumseh zs168fb (196cc/6.5hp) engine. I'm thinking one of ... A: >>I Used to Send the Auto Reject Answer, but I Think it Might be Confusing in a Situation like this ... | |
| snow flite 7/21 | 1/1/2011 |
| Q: I have a lawn flite (mtd) snow blower that was given to me in as is condition. This week I pulled it ... A: >>This Engine has an MCR Cam. >>This is a Low Compression Start Engine. >>The Engine Compression is ... | |
| Gokart starting | 1/1/2011 |
| Q: I've got a Carter Bros gokart with the Tecumseh zs168fb (196cc/6.5hp) engine. I'm thinking one of ... A: >>The Air Mixture Screw/s may be Out of Adjustment or it may be that the Carburetor has an ... | |
| kOHLER cv-675 | 12/31/2010 |
| Q: SAW YOUR RESPOSE TO ANOTHER POST ON THIS ENGINE: POST WAS-I recently had my 7 year old Craftsman ... A: >>Kohler, Tecumseh and the Other OEM's Produce Fairly Good Products these Days, but you Still get a ... | |
| needle valve sticking | 12/31/2010 |
| Q: Carb was dirty, took it off, disassembled it, sprayed everything with carb cleaner, metal tie wrap ... A: >>The ONLY Way to Properly Clean a Small Engine Carburetor is Soaking Overnight in Cleaner. >>The ... | |
| Maintenance on Toro Power Shift | 12/31/2010 |
| Q: Bought a Toro Power Shift snow blower (unknown vintage,I would guess mid 1990s as the guy I bought ... A: >>If you go to this Site Addy; https://lookup3.toro.com/partdex/default.cfm and Select "Start Parts ... | |
| Tecumseh 7.0 HP OHV snow blower engne | 12/30/2010 |
| Q: Do not have model number of friends snow blower. Please delete this if it is positively required. ... A: >>Thanks for the Comments. I Hope your Experience with All Experts is What you Expected. >>Adjusting ... | |
| Maintenance on Toro Power Shift | 12/30/2010 |
| Q: Bought a Toro Power Shift snow blower (unknown vintage,I would guess mid 1990s as the guy I bought ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| Tecumseh 7.0 HP OHV snow blower engne | 12/30/2010 |
| Q: Do not have model number of friends snow blower. Please delete this if it is positively required. ... A: >>From your Description it Sounds like the Spark Plug Gap Requires Setting, the Carburetor Requires ... | |
| Bolens Snowblower | 12/30/2010 |
| Q: My pull cord came off on my Bolens Snowblower. I have removed the cover and I see what looks like a ... A: >>I used an HM80-190000 for a Reference. >>You can View a Breakdown/IPL of this Engine at this Site ... | |
| snow thrower engine won't stop! | 12/29/2010 |
| Q: Craftsman snow thrower (electric and recoil starter) 247.88640, with Tecumseh engine (Craftsman # ... A: >>Remove the Blower Housing and Look at the Coil/Engine Shut Off Wire End. >>Is the Wire Still ... | |
| Honda Generator no fire | 12/29/2010 |
| Q: I have a Honda EU3000IS-EXGF-1175526 generator in the shop that came in with a no-fire condition. ... A: >>You can View a Breakdown/IPL at this Site Addy, ... | |
| Snow Blower Belts | 12/28/2010 |
| Q: I adjusted my snow blowers belt twice now. It's about 5 -7 years old. Do snow blower belts stretch ... A: >>Yes Sir they Do. >>Usually if you are Lucky you can get 3 or Maybe 4 Adjustments out of the Belts ... | |
| kawasaki fd620 | 12/28/2010 |
| Q: I have a Kawasaki FD620 20 hp engine. I broke the wire off of the fuel cut off solenoid, they are ... A: >>The Carburetor Solenoid is an Anti- Diesel Solenoid Designed to Prevent Gas from Entering the ... | |
| spark plugs | 12/28/2010 |
| Q: When checking the spark @ the spark plug should the color be just a bright blue or is it ok. if ... A: >>Bright Blue with a Slight Hint of Orange Mixed in is Good. >>An Orange with a Hint of Yellow Mixed ... | |
| Kohler CH12.5s Gov-shaft oil leak | 12/27/2010 |
| Q: I have a Kohler CH12.5s, spec# 1910, S/n# 2507405064 that is leaking oil from the gov-shaft. After ... A: >>They were Extra Busy Yesterday and the Service Rep said he thought there was a an Oil Seal ALso, ... | |
| Rebuilding a Briggs and Stratton | 12/27/2010 |
| Q: I have a B&S 5 hp motor off of a log splitter that I am trying to get running. Model 132232 Type ... A: >>The Following is an Example of Interpreting Date Code 6206282: The First Two Digits (62) Denote ... | |
| 5 hp briggs and stratton h/shaft | 12/27/2010 |
| Q: got a 5 hp briggs and stratton that i took off a tiller and made a go cart with. i now have more ... A: >>Is the Coil Firing when the Engine will Not Restart? >>Is the Spark Plug Wet when the Engine will ... | |
| Kawasaki FD620-AS12 | 12/27/2010 |
| Q: I recently bought the above listed engine and the guy selling told me it may have had the main jet ... A: >>Anytime you Change the Jet Size in a Carburetor you will have to Reset the Mixture Screw/s. >>The ... | |
| MTD Snow thrower 31A-2M1A762 | 12/26/2010 |
| Q: Merry Christmas. My MTD Model 31A-2M1A762 decided to not work just as we're about to have ... A: >>The Part Number 951-10955 is a Complete Recoil Starter Assy. >>Simply Remove the Blower Housing ... | |
| Husqvarna Rancher 455 Oiler Problem | 12/26/2010 |
| Q: My Husqvarna Rancher 455 Chainsaw goes through oiler pinion gear drives faster than a tank of gas. ... A: >>Where should I Start? >>I have Replaced 20 to 30 of these Oiler Drives/Pinions and Pumps and the ... | |
| 5 hp briggs and stratton h/shaft | 12/26/2010 |
| Q: got a 5 hp briggs and stratton that i took off a tiller and made a go cart with. i now have more ... A: >>Was the Valve Clearances Set COrrectly? >>The Following is a Basic Instruction File for Setting ... | |
| Toro Snow Pup starter rope replacement | 12/24/2010 |
| Q: I have a Toro Snow Pup (3104 704852). Can I replace the starter rope without pulling the engine? ... A: >>I could Not Locate your Model so I Used a Snow Pup from the Year 1977 for Reference. >>A Snow Pup ... | |
| Snow Chief Snow Shovel | 12/24/2010 |
| Q: I have a Snow Chief Power Shovel Model SC14SE and need a key for it. Any place I can contact for ... A: >>Any Small Engine Service Center will have a Key that Fits this Unit. >>If you Hit a Snag or this ... | |
| Craftsman Garden Tractor PTO switch | 12/24/2010 |
| Q: Craftsman Model 917.276081 Wires from the electric clutch were damaged by a belt failure. After ... A: >>If the Diode is Bad, then Remove it and take it with you to Radio Shack and Purchase a ... | |
| snow flite 7/21 | 12/23/2010 |
| Q: I have a lawn flite (mtd) snow blower that was given to me in as is condition. This week I pulled it ... A: >>No Worries. >>I am Here to Answer your Questions. >>The Carburetor Cleaner can be Purchased from ... | |
| Kohler CH12.5s Gov-shaft oil leak | 12/23/2010 |
| Q: I have a Kohler CH12.5s, spec# 1910, S/n# 2507405064 that is leaking oil from the gov-shaft. After ... A: >>According to My Shop Manual, there is a Cross Shaft Oil Seal Used on this Engine, but as you Noted ... | |
| Craftsman Garden Tractor PTO switch | 12/23/2010 |
| Q: Craftsman Model 917.276081 Wires from the electric clutch were damaged by a belt failure. After ... A: >>To View a Breakdown of this Unit Go to this Site Addy, ... | |
| snow flite 7/21 | 12/23/2010 |
| Q: I have a lawn flite (mtd) snow blower that was given to me in as is condition. This week I pulled it ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| wont idle,loss of power | 12/22/2010 |
| Q: i just bought a new go kart.it has a lifan 6.5hp,196cc engine.starting it is just like starting a ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| B&S SNOWBLOWER ENGINE BACKFIRES | 12/22/2010 |
| Q: John, I have a 8.5 HP B&S engine (Mod#15A114 Spec-0342 E1) that backfires alot and sometimes just ... A: >>You can View a Breakdown/IPL of the Engine at this Site Addy; ... | |
| Go Kart Help | 12/22/2010 |
| Q: I have a Streaker Go Kart I just bought. It has a Fun Power 5HP Engine thats all i know I can't ... A: >>The Fun Power is a Briggs and Stratton Engine Name. >>The Model Numbers May be Stamped Into the ... | |
| Snowblower | 12/22/2010 |
| Q: I have a Tecumseh Snow King snowblower, LH195SA. It will not start. I have changed the spark plug, ... A: >>If you have Not Soaked and Cleaned the Carburetor in Cleaning Solution, then the Carburetor can be ... | |
| GX670 | 12/21/2010 |
| Q: I have a HONDA 24hp GX670 engine mounted on a long shaft mud motor frame and the GX is working off ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| lawnboy 824E snowblower won't drive | 12/21/2010 |
| Q: I was using my snowblower and the wheels locked up. It won't drive forward or back and they remain ... A: >>Thanks. >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| lawnboy 824E snowblower won't drive | 12/21/2010 |
| Q: I was using my snowblower and the wheels locked up. It won't drive forward or back and they remain ... A: >>Depending on the Model it can be the Several Components (Chain, Drive Dawgs/Tangs, ect). >>The ... | |
| Tecumseh starter cup | 12/19/2010 |
| Q: I have a Tecumseh H-70-130266L engine on an Ariens snowblower. When I went to pull on the starter ... A: >>Thanks for the Picture. >>Ouch!! >>One of the Starter Tangs/Dawgs is Missing and the Starter ... | |
| Craftsman Model # 917.276240 | 12/19/2010 |
| Q: I blew the diode going to the electric clutch and want to know if you know what value/part # is on ... A: >>I am Not Sure of the Value of the Diode, but I will Look at the Unit that is in the Shop and have ... | |
| 2 cycle oil mix | 12/19/2010 |
| Q: can i put the same mix gas in my mcculloch super 10 10 auto as my new homelite? homelite is 50:1 ... A: >>All Two Stroke Engines will use a 50 to 1 Ratio using Today's Two Stroke Oils. I once had an Old ... | |
| 041 stihl farm boss chain saw | 12/19/2010 |
| Q: I reset the carb back to factory setting but the choke has to be about half way in order for the saw ... A: >>It Sounds like the Mixture Settings are Not Quite Correct. >>Try the Following, Just Skip the ... | |
| Tecumseh starter cup | 12/18/2010 |
| Q: I have a Tecumseh H-70-130266L engine on an Ariens snowblower. When I went to pull on the starter ... A: >>The Starter Cup (Tecumseh Part #32125) should be the Only Replacement Part you Require if the ... | |
| aircap snow champ snowblower repair | 12/18/2010 |
| Q: I need to find a parts diagram for an Aircap Snow Champ #8430 snowblower to replace a broken part ... A: >>Yes MTD is going to be the Parts and Breakdown Supplier for this Unit. >>You can View a ... | |
| 31625 toro snowblower | 12/17/2010 |
| Q: I need to change the belts on an old 31625 toro snowblower.Do I have to remove the main shaft and ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| Locking lever on Stihl backpack blower | 12/17/2010 |
| Q: I have a Stihl BR400 backpack blower, which I bought in 1994. It still runs great, but I'm trying ... A: >>Thanks for the Update. >>I will Make an Instruction File that has this Information in it for ... | |
| Adjust valves | 12/17/2010 |
| Q: I would like to know how to adjust the valves on a 12 horse, 4 cylinder,electric ignition for ... A: >>The Following is a Basic File I made for Setting the Valve Clearances. Any Input is Appreciated. ... | |
| Tecumseh 38120 2-cycle rod needle bearings | 12/16/2010 |
| Q: I am rebuilding a 38120 2-cycle Tecumseh. What is the best way to re-install the needle bearings ... A: >>You can View a Breakdown/IPL at this Site Addy, http://www.emerichsales.com/ and Select Tecumseh ... | |
| snowblower | 12/16/2010 |
| Q: can not get gas to carb i while put little gas in spark plug but it will not keep running A: >>Send me the Model and Type or Spec Numbers Off the Engine, Please. With these I can Locate the ... | |
| Honda GX670 voltage check | 12/16/2010 |
| Q: I installed a GX670 replacement engine on my Wheel Horse and it appears that the engine is not ... A: >>From your Description it Sounds like this Engine has the 3amp Charging Coil and Not the 20amp ... | |
| g150 honda engine | 12/15/2010 |
| Q: the engine was surging and i went through everything, and now i'm trying to get the crankcase cover ... A: >>Is the Stem that the Governor Turns on Bent? >>Straighten the Stem the Governor Turns on. >>Use ... | |
| Tecumseh 3.5 HP Snowblower Carb Setting | 12/15/2010 |
| Q: I have a Ariens Snow blower with a 3.5hp Tecumseh engine (H35-45515k Ser: 8191B) that I believe I ... A: >>The Following is an Instruction File I made for Correcting this Problem. Any Input is Appreciated. ... | |
| Tecumseh 38120 2-cycle rod needle bearings | 12/14/2010 |
| Q: I am rebuilding a 38120 2-cycle Tecumseh. What is the best way to re-install the needle bearings ... A: >>Most Mechanics use White Lith Grease to Hold the Bearings to the Crankshaft, but I have Found that ... | |
| JD LX178 | 12/14/2010 |
| Q: Just picked up a JD LX178 - engine turns over but does not start. Thinking its not safety switches ... A: >>On Some Models, the Safety Switches Prevent the Engine from Starting, Not Stopping the Starter ... | |
| Craftsman Snow Thrower - Starting Problems | 12/14/2010 |
| Q: John, Thanks in advance for helping me out! I have a Craftsman Model C959-52009 24" Snow Thrower. ... A: >>Check the Crankcase Oil for Gas Contamination. >>Usually the White Puff of Smoke is an Indicator ... | |
| Toro 180 throttle/governor linkage question | 12/13/2010 |
| Q: My Dad has a 2010 Toro PowerClear 180 4-cycle snow blower. He let it sit all summer after putting ... A: >>Sorry for the Delay. This Question was Located in the Question Pool. >>The Solid Linkage and the ... | |
| Size of thread for oilfill plug on a Tecumseh 9 hp | 12/13/2010 |
| Q: I would like to know what size thread is used on the Oil Fill Plug assembly for the following: ... A: >>Sorry for the Delay. This Question was Located in the Question Pool. >>This should be a 3/8" or ... | |
| dynamark snowthrower | 12/13/2010 |
| Q: Have a 7hp-3 stage snow-thrower,model#53620101 with automotive differential.Pushed great last year ... A: >>Can you Check the Model Numbers Again for me, Please. I cannot Locate this Model in my Manuals or ... | |
| Craftsman Snowblower Trac Problem | 12/13/2010 |
| Q: John, I have an old Craftsman Snowblower (5 23) with trac drive, model 536.884810. Its been a good ... A: >>From your Description of the Friction Wheel, it Sounds like there is a Problem with the Drive. ... | |
| toro ccr 1000 snowblower wont stay running | 12/13/2010 |
| Q: Good evening. Thank you for looking at my question. I have a Toro ccr1000 snowblower model 38190 I ... A: >>Make Sure the Gas is Free Flowing to the Carburetor. >>If the Gas is Free Flowing to the ... | |
| Murray/Tecumseh Drive Won't Engage | 12/12/2010 |
| Q: I have a 24 inch Murray snow blower with a 5hp Tecumseh engine. After using it last night, I went ... A: >>Send me the Model Numbers Off the Unit, Please. With these I can Locate the Proper Manual and ... | |
| Honda GX390 | 12/12/2010 |
| Q: I Have a Honda GX390 Serial # GCAKT1427916 TYPE QAA2 that is used on a pressure washer. I need to ... A: >>You are Correct, the Untapped Mounting Bosses Under the Flywheel are for Mounting Different Amp ... | |
| HSK 50 Carb rebuild | 12/12/2010 |
| Q: I have a Tecumseh HSK 50 Engine on an Ariens 5 HP Snow Blower. It uses a p/n 67244f or Oregon repl ... A: >>Thanks for the Comments and Ratings. >>You Might Require the Procedure for Setting the Mixture ... | |
| HSK 50 Carb rebuild | 12/11/2010 |
| Q: I have a Tecumseh HSK 50 Engine on an Ariens 5 HP Snow Blower. It uses a p/n 67244f or Oregon repl ... A: >>Go to this Site Addy; http://www.emerichsales.com/pages/parts/viewbybrand/default.aspx and Select ... | |
| HSK 50 Carb rebuild | 12/11/2010 |
| Q: I have a Tecumseh HSK 50 Engine on an Ariens 5 HP Snow Blower. It uses a p/n 67244f or Oregon repl ... A: >>The Bowl Washer goes on the Inside Between the Bowl and the Carburetor. >>The Lower Mixture Screw ... | |
| HSK 50 Carb rebuild | 12/11/2010 |
| Q: I have a Tecumseh HSK 50 Engine on an Ariens 5 HP Snow Blower. It uses a p/n 67244f or Oregon repl ... A: >>I Require the OEM (Walbro, Zama, ect) and the Model Numbers Off the Carburetor. With these I can ... | |
| Bolen's Snowblower | 12/11/2010 |
| Q: John, I have an old Bolens snowblower, Model 832 01. Today, it stopped going forward in any gear and ... A: >>Send me the Model Numbers Off the Unit, Please. With these I can Locate the Proper Manual and ... | |
| tecumseh govenor shaft | 12/11/2010 |
| Q: Tecumseh engine will go from idle to a very high revs with just a slight movement of the throttle ... A: >>There should be Some Movement, but 3/8" Seems to be a Bit Much. >>Usually 1/8 to 1/16" is All the ... | |
| mtd snowblower model#31a-2m1a752 part#951-10955 | 12/10/2010 |
| Q: My rope broke on the snowblower today and i tried taking apart to fix it and i got it off and i ... A: >>You can View a Breakdown/IPL of this Unit at this Site Addy, ... | |
| Toro Power Clear 221Q (38583) idle issue? | 12/10/2010 |
| Q: My 3 year old snow thrower isn't throwing snow like it should. The belt is tight, the scraper bar ... A: >>I am Sorry for your Experience at the Repair Shop. >>Most Repair Shops do Not do as you Described. ... | |
| Tecumseh 5HP stalling under snow load | 12/9/2010 |
| Q: Same isuues as Roger had on 1-8-2008 but I have a Troybilt #42000. Expert: John C. Bridgers Sr. - ... A: >>If this is an OHV Engine, then >>The Valve Clearances may Require Setting. >>The Carburetor Float ... | |
| toro s-620 | 12/9/2010 |
| Q: Hey John I have, well my brother in-law has a toro s-620 he said i wouldn't run good, me and my ... A: >>Send me the Model Numbers Off the Unit, Please. With these I can Locate the Correct Manual and ... | |
| Timing on Briggs and Stratton Animal | 12/9/2010 |
| Q: Model Number 124332 Type 8003-01 I bought an animal motor and everything was taking apart, I was ... A: >>There is a Mark (-) on the Crankshaft Gear Tooth and a Dot(.) between the Teeth on the Cam that ... | |
| Homelite super 2 chainsaw | 12/8/2010 |
| Q: After started, runs fine for about one minute then stalls. trouble getting re-started. Once it does ... A: >>There should be a Return Line from the Carburetor to the Tank. >>That is What the Second Hole in ... | |
| Can i pressure clean an engine | 12/8/2010 |
| Q: I have a Honda GX110 small engine, and i was wondering how you can clean it. There is a lot of oil ... A: >>If you Blow the Engine and Unit Off with Compressed Air and Use the Compressed Air to Blow Out the ... | |
| Can i pressure clean an engine | 12/8/2010 |
| Q: I have a Honda GX110 small engine, and i was wondering how you can clean it. There is a lot of oil ... A: >>All the Equipment Used here is Washed Each Time it is Returned to the Shop. >>A Pressure Washer ... | |
| Briggs stratton engine | 12/8/2010 |
| Q: I have a 42" country clipper "0" turn mower-4 years old 430 hours. It has a briggs-stratton engine ... A: >>If the Cylinder was Not Damaged, then a New Oil Pump, Crankshaft and Connecting Rod are Required ... | |
| toro ccr 2000e | 12/7/2010 |
| Q: i have a Toro ccr 2000e snow thrower i recently cleaned the carb now when the engine warms up it ... A: >>The Following is an Instruction File I Made for Setting the Governor Arm Correctly. Any Input is ... | |
| tiller | 12/7/2010 |
| Q: I have a 7hp rear tine tiller. I was having shifting problems I decided to repair my self. I must ... A: >>The Breakdown at the Sears Site for the Transmission is the Same Breakdown in my Manual. >>I will ... | |
| idle adjustment | 12/7/2010 |
| Q: I have a Cub Cadet Commercial Z turn tank model with a Honda GXV620 Engine recently it started ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| Briggs & Stratton Spark | 12/6/2010 |
| Q: I have a old Briggs and Stratton Engine 130202 0135 on a old Ford Tiller. I replaced the Armature, ... A: >>OK. That Explains a Lot. >>Disconnect the Point Set from the Ground. >>This Style Shut Off System ... | |
| Briggs & Stratton Spark | 12/6/2010 |
| Q: I have a old Briggs and Stratton Engine 130202 0135 on a old Ford Tiller. I replaced the Armature, ... A: >>If you Disconnected the Armature Groung and have Fire to the Plug, then >>Check the Cutoff Switch ... | |
| Horse pony tiller | 12/6/2010 |
| Q: John, I bought a used older troybuilt pony rear tine tiller and it seems to always 'freewheel'. I ... A: >>The Wheel Axle Gear May have Moved/Shifted on the Wheelshaft, the Wheelshaft may have ... | |
| Recommended Oil | 12/5/2010 |
| Q: I need to change the oil in my sister-in-law's mower - no manual. It is a John Deere LX178 with a ... A: >>I Use SAE 10W30 Synthetic Engine Oil in My Equpiment, both Landscaping and Automotive. >>The ... | |
| replacement belts for a mtd snowflite 5/24 | 12/5/2010 |
| Q: I need to replace the belts on a MTD SNOWFLITE 5/24. The model tag reads 319-600 11288. I have part ... A: >>The Correct Belt Part Numbers for this Unit are as Follows; MTD 754-222KVLR is a MTD 754-0222 (44" ... | |
| John Deere LX172 Deck blade Problem | 12/5/2010 |
| Q: My last mowing, I was able to get 1/2 way through my lawn when the deck blades stopped turning. When ... A: >>Yes, Checking the Stator and Voltage Regulator (if Applicable) is your Next Step. >>As I Stated in ... | |
| tiller | 12/4/2010 |
| Q: I have a 7hp rear tine tiller. I was having shifting problems I decided to repair my self. I must ... A: >>To View a Breakdown of this Unit Go to this Site Addy, ... | |
| Tecumseh HM80 | 12/4/2010 |
| Q: What is the recommended torque for the headbolts of a tecumseh HM-80-115112A motor? A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| B&S 4-Stroke Motor Hunting | 12/4/2010 |
| Q: I have a rather old Masport 635 mower with B&S 4 stroke motor Model 100708, Type 0129-04, Code 8806 ... A: >>You have 1 of the Last of the Best Engines that were Once made by Briggs & Stratton. >>This ... | |
| Locking lever on Stihl backpack blower | 12/4/2010 |
| Q: I have a Stihl BR400 backpack blower, which I bought in 1994. It still runs great, but I'm trying ... A: >>We have a Special Tool that the Company Purchased from Stihl to Install the Throttle Lock Levers. ... | |
| John Deere TRS 26 Snow Thrower | 12/3/2010 |
| Q: My Snow thrower is about 18 yrs old and still starts and runs good; but it doesn't throw snow like ... A: >>If this Unit has been in Use for 18 Years and has had Routine Waintenance Performed on it and it ... | |
| head bolts | 12/3/2010 |
| Q: I am looking for the location of the three longer headbolts on a briggs 16hp model#402437 ... A: >>The Briggs Part # is 93113. >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| 1986 Victa 2 stroke lawn mower recoil spring | 12/3/2010 |
| Q: I have a victa lawn mower 1986 2 stroke and the starter cord will not rewing. I think the recoil ... A: >>The Following is a Basic Horozontal Recoil Starter Repair Instruction File. Any Input/Suggestions ... | |
| 11 hp briggs and stratton riding lawn mower | 12/2/2010 |
| Q: roper riding lawnmower -11 hp B&S -4 gears (reverse, 1, 2, 3) -has headlights -has brakes (located ... A: >>Yes I can. >>Most Diesel Repair Centers will have or can Usually get an Engine Block Heater that ... | |
| Chain Saw Parts | 12/2/2010 |
| Q: I have a Craftsman Chain Saw Model 316.350840 18 In. 55CC engine. Some fins broke off of my flywheel ... A: >>This is a Ryobi Unit made for Sears. >>Try outdoordistributors.com/ , they have the Flywheel ... | |
| Honda GX160 Over-revs out of CHOKE | 12/2/2010 |
| Q: I have recently received a Honda tiller from my parents that did not work. The engine had locked up ... A: >>Try Setting the Governor Arm First. >>The Following is an Instruction File I Made for Setting the ... | |
| craftsman lt 1000 lawn tractor electrical problem | 12/1/2010 |
| Q: finished mowing and cleaned tractor. 18 HP B&S engine OHV about 8 years old. Started, but when the ... A: >>From your Description it Sounds like the Seat Safety or the Connection for the Seat Safety is Bad ... | |
| Homelite super 2 chainsaw | 12/1/2010 |
| Q: After started, runs fine for about one minute then stalls. trouble getting re-started. Once it does ... A: >>This Problem can be caused by the Carburetor Metering Valve Sticking, a Restricted Muffler/Ehaust ... | |
| Gokart won't run in cold. | 12/1/2010 |
| Q: I have a gokart with a Briggs and Stratton engine Model number 136212. I have had tons of problems ... A: >>I have Not Located a Site that Offers that kind of Picture, however >>I have 1 of these Units in ... | |
| Gokart won't run in cold. | 11/30/2010 |
| Q: I have a gokart with a Briggs and Stratton engine Model number 136212. I have had tons of problems ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| craftman leaf blower | 11/30/2010 |
| Q: My craftsman leaf blower has the exact problem described by Tham. The one thing I found is that if ... A: >>This Unit is Made for Sear by Ryobi. >>To View a Breakdown of this Unit Go to this Site Addy, ... | |
| LX178 Question | 11/30/2010 |
| Q: Question about my LX178. As of recently, my LX178 has been leaking a little bit of oil directly ... A: >>From your Description it Sounds like the Deck Drive Belt is Contaminated with Oil and is Slipping ... | |
| kohler ch18 blowing compression through the intake | 11/29/2010 |
| Q: i have a kohler ch18 that lost power but ran. found out one cylinder wasnt firing all the time. ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| kohler generator | 11/29/2010 |
| Q: my generator (kohler 60rozj 60kVA) gives auxiliary fault and shutdown immediately ,the controller ... A: >>If you have Checked All the Sensors and Safety Switches/Sensors, then >>You need to Locate a ... | |
| Honda HRA214 Blade Brake Removal | 11/29/2010 |
| Q: I have a Honda HRA214 SA from the mid '80's with a GXV120 engine that I am trying to get into the ... A: >>It is VERY IMPORTANT that you Hone the Cylinder before you Install the New Rings. >>The Honing of ... | |
| craftman leaf blower | 11/29/2010 |
| Q: My craftsman leaf blower has the exact problem described by Tham. The one thing I found is that if ... A: >>Check/Replace the Fuel Line in the Tank. >>Usually when this Occurs the cause is a Bad Fuel Line ... | |
| kohler generator | 11/28/2010 |
| Q: my generator (kohler 60rozj 60kVA) gives auxiliary fault and shutdown immediately ,the controller ... A: >>Thanks for the Information. >>You need to Check the Coolant Sensor and the Wire for the Coolant ... | |
| Briggs & Stratton model # | 11/28/2010 |
| Q: I hope you can help us with this, I've been searching on line for awhile now. We have a MTD tiller ... A: >>Thanks for the Comments and Ratings. >>That Spark Plug is a Listed Replacement. >>This Site Addy; ... | |
| Honda HRA214 Blade Brake Removal | 11/28/2010 |
| Q: I have a Honda HRA214 SA from the mid '80's with a GXV120 engine that I am trying to get into the ... A: >>It Sounds like the Woodruff Key has Rusted to the Blade Clutch/Brake. >>Soak the Crankshaft with ... | |
| Poulan PPB100 Pull Cord | 11/27/2010 |
| Q: can you tell me or provide access to a diagram that shows how to get to the pull cord assembly? I ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| kohler generator | 11/27/2010 |
| Q: my generator (kohler 60rozj 60kVA) gives auxiliary fault and shutdown immediately ,the controller ... A: >>Send me the Model and Type or Spec Numbers Off the Engine and the Unit/Mower Model Numbers, ... | |
| Portable generator problems | 11/27/2010 |
| Q: My generator is a Devilbiss Model # GBVE8000-WK, serial # 9912120701. It has been working fine. My ... A: >>The 240 Circuit Consists of 2 120V Wires and 1 Neutral/Ground Wire to give you the 240V. >>Most ... | |
| Briggs and Stratton 5 hp 206 cc | 11/26/2010 |
| Q: I hope you can help us with this, I've been searching on line for awhile now. We have a MTD tiller ... A: >>All Briggs and Stratton models except twin cyl., Vanguard Intek, and 19A400 - 19G400 series Use a ... | |
| Weedeater featherlite xt200 carb | 11/26/2010 |
| Q: I replaced a primerbulb on a Zama C1U-W7 carb, and had problems starting it afterward. I ... A: >>The Following is the Instruction File for Setting the Air Mixture Screws. Any Input is ... | |
| toro mower online repair manual | 11/26/2010 |
| Q: I would lioke to know if there is a web site that shows the online repair manual with blowout ... A: >>Sorry for the Delay. >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| fuel pump leak | 11/25/2010 |
| Q: Every year I replace the fuel pump on my briggs and stratton 8hp leaf blower engine. 4 years, 4 ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| mower not starting | 11/25/2010 |
| Q: First let me apologize for any spelling or grammar errors. I have a Murray 42" riding mower with a ... A: >>Sorry for the Delay. >>Check the Connections at the Seat where it was Bypassed. >>The Following is ... | |
| Toro Snowthrower Question | 11/25/2010 |
| Q: have a 1984 Toro Model 38040 Snowthrower2 stage that I can not get to start. I can get it to fire ... A: >>The Spring that the Pin goes through is Attached to the Knob at the Top of the Needle Valve. >>It ... | |
| Tecumseh H-50 65242H Carb. Butterfly | 11/24/2010 |
| Q: No matter what I do I can't get the engine to idle with the choke off. It shuts off immediately ... A: >>Due to the Many Carburetor OEM's, I want to be Sure we are Looking at the Same Carburetor. >>I ... | |
| Tecumseh H-50 65242H Carb. Butterfly | 11/24/2010 |
| Q: No matter what I do I can't get the engine to idle with the choke off. It shuts off immediately ... A: >>That is the Correct Configuration. >>What is the Engines Compression? >>Have the Valve Clearances ... | |
| fuel pump leak | 11/24/2010 |
| Q: Every year I replace the fuel pump on my briggs and stratton 8hp leaf blower engine. 4 years, 4 ... A: >>Send me the Model and Type or Spec Numbers Off the Engine, Please. With these I can Locate the ... | |
| 5 hp Tecumsuh Engine on JD 524 Snowblower | 11/23/2010 |
| Q: The 5 hp engine on my JD TRS524 snowblower does not have lugging power--I bought it new and it has ... A: >>I Usually Suggest an 8HP Minimum Engine on the 24" 2 Stage Snow Blowers/Snow Throwers. >>I have ... | |
| fuel pump leak | 11/23/2010 |
| Q: Every year I replace the fuel pump on my briggs and stratton 8hp leaf blower engine. 4 years, 4 ... A: >>If this Engine is Electric Start or has a Battery, then >>You can Use an Electric Fuel Pump, Mr ... | |
| Bent push tubes B&S 24hp vert v twin | 11/23/2010 |
| Q: I have a sears lawn tractor with the above described engine Model 445677, type 0476Ei family 6Bsxs ... A: >>The Probelm with the Push Tubes is a Common One since the OHV Engine has become a Popular Engine ... | |
| Troy-built horse kills | 11/22/2010 |
| Q: I lack small-engine experience, but also due to lack of time and need of tilling before freeze, sent ... A: >>I Understand How You Feel about Not Removing Any Parts from the Engine as you Say you are Not ... | |
| The craftsman is Stuck | 11/22/2010 |
| Q: Sr., I have a craftsman tractor stuck in the middle of my yard , The model # is 917-271110, 6 speed ... A: >>Did you make Sure the Belt was Not Stuck to the Transaxle Input Shaft Pulley? >>Loosen the Belt ... | |
| oil in snowblower | 11/22/2010 |
| Q: i have an ariens 1976 snowblower 8/24 with a tecumseh 8hp engine model # HM80-155128c ser-6302d. ... A: >>I Use SAE 10W30 Synthetic Engine Oil in My Equpiment, both Landscaping and Automotive. >>The ... | |
| amf 70s snow blower | 11/22/2010 |
| Q: well i have a questions 1 can u convert to electric start it is a 5 hp 2 stage 5 speed model ... A: >>Most of these Engines can be Converted to Electric Start. >>Send me the Make, Model and Type or ... | |
| Gas Blower Ignition coil | 11/21/2010 |
| Q: I saw your response to a similar problem (i.e., engine won't start). Problem traced to ignition ... A: >>You cannot Parts from Echo, but you can Contact them and Inquire about a Replacement Coil for ... | |
| John Deere LX172 Deck blade Problem | 11/21/2010 |
| Q: My last mowing, I was able to get 1/2 way through my lawn when the deck blades stopped turning. When ... A: >>I Failed to give you the Instruction File for Removing the PTO. >>To Remove the PTO; >>Remove the ... | |
| The craftsman is Stuck | 11/21/2010 |
| Q: Sr., I have a craftsman tractor stuck in the middle of my yard , The model # is 917-271110, 6 speed ... A: >>The Easiest Way to Move this Unit is to Take Off the Ground Drive Belt at the Engine Pulley. ... | |
| John Deere LX172 Deck blade Problem | 11/20/2010 |
| Q: My last mowing, I was able to get 1/2 way through my lawn when the deck blades stopped turning. When ... A: >>The Volyage should Never Change. >>What is the Output of the Stator/Charging Coils. >>If the ... | |
| Tiller Part | 11/20/2010 |
| Q: OriginalI have an MTD (hechinger) model 219-381-372 rotor tiller and need part 784-0093-0637 TINE ... A: >>Darn I Hate when that Happens. >>You can Try www.mtdparts.com . >>If they Don't have the Part, ... | |
| primer bulb will not expand | 11/20/2010 |
| Q: craftsman model number 358.797170 i am unable to have the primer bulb expand after compressing it. ... A: >>You can View a Breakdown/IPL of the Carburetor and Get Technical Information on Zama Carburetors ... | |
| Troy-built horse kills | 11/19/2010 |
| Q: I lack small-engine experience, but also due to lack of time and need of tilling before freeze, sent ... A: >>Thanks for the Model Numbers. >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| McCulloch MCP 1510 10 inch 1.5 HP Electric Pole Saw | 11/19/2010 |
| Q: I have a McCulloch MCP 1510 10 inch 1.5 HP Electric Pole Saw with removable 10-foot pole. The saw is ... A: >>The Best Company I have Found for McCulloch Parts is Ordertree.com >>You can Contact them at ... | |
| Troy-built horse kills | 11/19/2010 |
| Q: I lack small-engine experience, but also due to lack of time and need of tilling before freeze, sent ... A: >>From your Description it Sounds like the Carburetor Mixture Screws Require a Slight Tweeking Due ... | |
| primer bulb will not expand | 11/19/2010 |
| Q: craftsman model number 358.797170 i am unable to have the primer bulb expand after compressing it. ... A: >>To View a Breakdown of this Unit Go to this Site Addy, ... | |
| Honda GX270 surging | 11/18/2010 |
| Q: I have a Simpson pressure washer with a Honda GX270 engine. What makes the engine surge under a ... A: >>I Do Understand where you are Coming from about the Holiday Seasons. >>We All Celibrate in Our Own ... | |
| engine starts but wont keep running | 11/18/2010 |
| Q: I have a 1999 Homelite generator 8 Hp 4000 W Pull start It has an 8 Hp Briggs and Stratton Engine ... A: >>The Biggest Problems with Generators is the Carburetors. >>From your Description it Sounds like ... | |
| how to replace oil presser sending unit | 11/18/2010 |
| Q: I have a Snapper zero turn riding lawnmower model#:ZF2501KH. It has a Kohler Command Pro 25 engine ... A: >>The Oil Sentry Switch is Located Under the Breather Cover. >>The Best Way to Tell you the Location ... | |
| Honda GX270 surging | 11/17/2010 |
| Q: I have a Simpson pressure washer with a Honda GX270 engine. What makes the engine surge under a ... A: >>No Worries. >>It Happens to All of Us from Time to Time. >>Tell your Wife, I Forgive Her; Just ... | |
| Tecumseh HM 80 155334-M governor adjustment | 11/17/2010 |
| Q: I removed and cleaned carburetor on a Tecumseh HM80, 155334-M 8 hp. engine. (ON a yardman model ... A: >>You are More than Welcome for Any Assistance I can Give you. >>You are Correct. >>Since you have ... | |
| MTD (hechinger) model 219-381-372 | 11/17/2010 |
| Q: need outer LH tine replacement (part # 784-0093) A: >>You can Purchase this Part from Small Engine Parts Warehouse (ph:262-338-2316). >>It is Priced at ... | |
| Tecumseh HM 80 155334-M governor adjustment | 11/17/2010 |
| Q: I removed and cleaned carburetor on a Tecumseh HM80, 155334-M 8 hp. engine. (ON a yardman model ... A: >>The Following is an Instruction File I Made for Setting the Governor Arm Correctly. Any Input is ... | |
| Dixon Mower idler spring | 11/17/2010 |
| Q: I have a 1990 Dixon ZTR428 mower. The mower deck drive belt broke. It knocked loose the idler ... A: >>You can View a Breakdown of this Unit at this Site Addy; http://www.dixon-ztr.com/ and Select ... | |
| Honda GX270 surging | 11/16/2010 |
| Q: I have a Simpson pressure washer with a Honda GX270 engine. What makes the engine surge under a ... A: >>Since this is a Honda, you can Use this Site Addy; http://www.honda-engines-eu.com/en/welcome.html ... | |
| Portable generator problems | 11/16/2010 |
| Q: My generator is a Devilbiss Model # GBVE8000-WK, serial # 9912120701. It has been working fine. My ... A: >>Make Sure of the Wiring First. >>It Sounds like a Wire is Grounded or has been Attached to the ... | |
| John Deere LX172 Deck blade Problem | 11/16/2010 |
| Q: My last mowing, I was able to get 1/2 way through my lawn when the deck blades stopped turning. When ... A: >>From your Description it Sounds like the PTO Requires Adjusting/Replaced or the Stator/Voltage ... | |
| Kohler M20 | 11/15/2010 |
| Q: Good morning, I have a Bolens tractor, with a kohler M20, which had a governor issue that ended up ... A: >>Stop where you are. >>Remove the Washer from the Filter Plate. >>You have to Remove the Closure ... | |
| CCR2000 Backfire after a few minutes | 11/15/2010 |
| Q: I have a 1993 Toro CCR2000 model 38180, serial no. 3909332 It runs for about 5 minutes and then ... A: >>Did you Check the Ring End Gap before Installing the New Ring Set? >>What was the Ring End Gap? ... | |
| Stator Output Voltage | 11/15/2010 |
| Q: I have a B&S engine model # 42E707, Type# 2631-E3 currently mounted on a Sears mower requiring 3 ... A: >>The Stator Output cannot be Changed, but the Stator can be Replaced with a Larger Output Stator. ... | |
| John Deer RX95 | 11/14/2010 |
| Q: Mower starts and cuts off when I engage transmission. Replaced seat safety switch but problem still ... A: >>Since you have Replaced the Seat Safety, then >>The Next Course of Action is to Check the Neutral ... | |
| carburetor choke | 11/14/2010 |
| Q: I was blowing leaves today and the machine started to miss and then died suddenly i checked it over ... A: >>Some of these Carburetors have Replaceable Parts such as the Choke and Throttle Plates as well as ... | |
| best wwy to clean spark arrestor | 11/14/2010 |
| Q: It's in good shape otherwise. How best to clean. Thank you so very much for your time. I'm sure you ... A: >>A Wire Brush is the Best Way and Remember Not to Flex the Screen too Much as the Screen is Usually ... | |
| Craftsman Riding Mower 17 HP Briggs & Stratton | 11/13/2010 |
| Q: I have a Crafstman riding mower that has a B&S 17 HP engine that is about 10-11 years old. The ... A: >>Thanks for the Model Numbers. >>Did Setting the Valve Clearances Not Correct the Problem with the ... | |
| PRESSURE SENSITIVE SEAT ON A LAWN TRACTOR | 11/13/2010 |
| Q: I recently borrowed my neighbor's Craftsman lawn tractor to vacuum up some leaves. He proceeded to ... A: >>I have Never Heard of or have I Seen a Problem being caused by Leaving the Seat of a Ride on Mower ... | |
| LX188 oil in water | 11/13/2010 |
| Q: I have a John Deere LX188 '94 model with a typical FD501V Kawasaki engine. Recently I had two ... A: >>You are Correct about the Water Pump and that is the Next Place to Look for the Oil in Water ... | |
| Craftsman Riding Mower 17 HP Briggs & Stratton | 11/13/2010 |
| Q: I have a Crafstman riding mower that has a B&S 17 HP engine that is about 10-11 years old. The ... A: >>From your Description of How the Engine is Turning During the Start Procedure, it Sounds like the ... | |
| How do you lubricate the starter mechanism for a Briggs and Stratton lawn mower | 11/13/2010 |
| Q: I have a Briggs & Stratton Quantum XM 50 engine After starting the engine, the machine makes a high ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Lawn Mower won't Stay Running | 11/12/2010 |
| Q: I have a lawn mower with a 3.5hp Briggs and Stratton engine. The numbers on the engine are ... A: >>From your Description (especially of the Primer Bulb Action) is Sounds like the Carburetor ... | |
| 8 hp Tecumseh | 11/12/2010 |
| Q: The governor makes the engine rev once or twice then it smoothes out when increasing the load. What ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Tecumseh H50 65242H oil in Piston Cylinder | 11/12/2010 |
| Q: I noticed a large amount of smoke coming out of the valve cover breather tube. I have a loss of ... A: >>Hi Again Thomas: >>Oil in the Cylinder when the Head is Removed is Normal as Long as it was Not ... | |
| How do I line up crank shaft and valves | 11/12/2010 |
| Q: I have a Briggs & Stratton 17HP riding mower engine I had to take apart and now am having problems ... A: >>From your Description it Sounds like the Connecting Rod/s were Attached to the Crankshaft Wrong. ... | |
| Briggss & Stratton Engine Model 31707 Type # 0137-E1 | 11/12/2010 |
| Q: I purchased a Craftsman Lawn Tractor in 9/2002 with engine on the subject line. When starting the ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Tecumseh H50 running bad | 11/11/2010 |
| Q: I noticed a large amount of smoke coming out of the valve cover breather tube. I have a loss of ... A: >>A Small Amount of Oil in the Bottom of the Crankcase Breather/Vent is Normal. >>If you Shake the ... | |
| generator problem | 11/11/2010 |
| Q: My generator cuts out even when under low load The engine runs ok and after 30 = 40 seconds it ... A: >>Send me the Make and Model Numbers Off the Unit, Please. With these I can Locate the Proper Manual ... | |
| Removing flywheel from Sears snowthower | 11/11/2010 |
| Q: I just bought a new snowthrower (247.886911) from Sears. The ad listed it as headlight optional, ... A: >>The Following is the Instruction File I Made for Removing the Flywheel from Most Mower Engines for ... | |
| Tecumseh H50 running bad | 11/11/2010 |
| Q: I noticed a large amount of smoke coming out of the valve cover breather tube. I have a loss of ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| Kohler small engine carb rebuild | 11/10/2010 |
| Q: How do I rebuild a carb for Kohler model #CV490 type #27508?I bought kit 12 757 03-S. Both needle ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| smoke from exhaust | 11/10/2010 |
| Q: ANSWER: Hello Leo:: >>Check the Engines Crankcase Breather/Vent for Oil Contamination, a ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| John Deere SX75 | 11/10/2010 |
| Q: I have a well maintained JD SX75. Over the last several months, when riding it in "gears" 3 thru 7, ... A: >>Have Someone Move the Ground Speed Lever while you Watch the Linkage. >>If the Sheave is Moving ... | |
| Need carb help on honda gx140 | 11/10/2010 |
| Q: I have my uncles 5.0 hp gx 140 honda it is in a go kart and the carb leaks gas and also there is no ... A: >>You have to Replace the Sprocket Drive Pulley with a Belt Drive Pulley on the Go-Cart. >>You ... | |
| proper oil | 11/10/2010 |
| Q: I have a Briggs/Stratton 10 HP OVH engine on my generator. Do I use 2 cycle or 4 cycle oil? A: >>This Engine uses 4 Cycle Engine Oil like Automobile Engines use. >>I Use SAE 10W30 Synthetic ... | |
| smoke from exhaust | 11/10/2010 |
| Q: Hi i have a craftsmen 21hp bs motor tracter I hit a big root in yard ever since noticed smoke coming ... A: : >>Check the Engines Crankcase Breather/Vent for Oil Contamination, a Damaged/Bent/Sheared ... | |
| Weedeater BC24w won't run when hot | 11/9/2010 |
| Q: My Weedeater BC24W line trimmer starts easily from cold and runs OK on half choke until it warms up, ... A: >>Did they Change the Fuel Filter in the Tank when they Serviced this Unit? >>Has the Carburetor ... | |
| Bad carburator | 11/9/2010 |
| Q: I need to find a carburetor for a 70's simplicity S5 snow blower with 5hp motor. Don't know where ... A: >>What is the Engine Make? Briggs, Tillotson, ect. >>What is the Carburetor Brand? Tillotson, ... | |
| Engine Governor setting | 11/9/2010 |
| Q: I have a 26hp Briggs ELS engine. I had to split the case and remove a rod that bent and went into ... A: >>A Quick Question First, Please. >>Did you Hone the Cylinder that you Pulled the Piston from when ... | |
| honda harmony 1011 | 11/8/2010 |
| Q: Trying.to remove the body but can't get the steering wheel off. I have the bolt our but can't budge ... A: >>Have you Soaked the Slip Fitting of the Steering Wheel and Shaft with Liquid Wrench or some Other ... | |
| Swapping engine | 11/8/2010 |
| Q: Changing 20hp Kawasaki FD620D-AS17 to 27hp Kawasaki FD750D-S01. I want to put the 27 hp in a 98 ... A: >>If you Wish me to Contact you, you can Send me a New E-Mail Question Marked Private and Include a ... | |
| 8 hp B&S Vertical Shaft Engine | 11/7/2010 |
| Q: I have an old Murray Rider that I am reworking the engine. Model 190707 Type 5631-01 Code ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Briggs & Stratton 16hp misfires then stalls | 11/7/2010 |
| Q: B&S 280777 0639-E1 9902042D, ie Vanguard 16hp Single-cyl circa 1999, for Victa Corvette ride-on. ... A: >>The Following is a Basic Instruction File I made for this Type of Problem. Any Input is ... | |
| Not getting fuel LA 145 Deere | 11/7/2010 |
| Q: There are two wires in a clip going to the bowl of the carb. I know there is fuel getting to the ... A: >>You are Asking about the Carburetor Solenoid. >>The Following is a Basic Instruction File I made ... | |
| Yardman leafblower | 11/6/2010 |
| Q: Have 3 yr. old. Yardman blower model YM320BV. Changed plug, cleaned air cleaner and spark arrestor. ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Tecumseh Eager-1 6.5 Sump leak | 11/6/2010 |
| Q: I have a Tecumseh Eager-1 6.5hp (143.976500) on a craftsman mower (917.377291). The engine is ... A: >>The Sump Gasket Leaking is a Common Problem with Small Engines. >>Remove the Engine from the Frame ... | |
| Toro-Stalls | 11/6/2010 |
| Q: The Auger has Been Stalling when Under a Load and Stalls now just at Idle(tried to adjust idle and ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| chain saw timin | 11/6/2010 |
| Q: I installed electronic ignition in my Eager beaver 120, but it fires to early. How do I time this ... A: >>The Flywheel Key Sets the Timing for this Saw. >>The Ign Coil is Gapped to .020in from the ... | |
| throttle jamming on briggs & stratton | 11/6/2010 |
| Q: the throttle keeps jamming on my mower, the mower wont turn off unless I shove it closed with a ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| HONDA GX270 | 11/5/2010 |
| Q: HOW DO I SET THE GOVERNOR ON HONDA GX 270 A: >>The Following is an Instruction File I Made for Setting the Governor Arm Correctly. Any Input is ... | |
| lawn mower engine | 11/5/2010 |
| Q: model 9d902 b1 thanks. A: >>This Problem can be Caused by a Dirty Carburetor, Burnt Valve or the Valve Clearances Require ... | |
| JD LX176 will not turn with the switch | 11/5/2010 |
| Q: My 176 was running fine. Now it will not turn with the switch. I can bypass the starter solenoid and ... A: >>The Following is an Instruction File for the Safety Switch System. Any Input is Appreciated. ... | |
| Sears chain Drive Roto Spader | 11/5/2010 |
| Q: I have a very old Sears Chain Driv Roto Spader model no 917.294560. It was working fine but all of ... A: >>From your Description it Sounds like the Recoil Starter may be Binding or the Engine was Run with ... | |
| gx120 honda pump | 11/4/2010 |
| Q: gettting intermittant spark. is there a procedure for testing electronic ignition compononts. has ... A: >>The Erratic Spark can be Caused by a Bad Ign Coil/Magneto, Bad Spark Plug or a Bad Safety Switch. ... | |
| Leaf Blower | 11/4/2010 |
| Q: I own a Craftsman leaf blower, model # 517.797942, that's about 14 years old. I put in a new spark ... A: >>Before Considering a New Carburetor; Check the Muffler and Exhaust Port. >>The Following is a ... | |
| Tecumseh 3.5 vantage running problem | 11/3/2010 |
| Q: My lawnmower has this engine fitted and after about 30 minutes running starts to splutter and cough ... A: >>You are Correct. I am Talking about the Coil/Magneto. >>I could Not Locate this Engine Model in my ... | |
| Removal of fly wheel | 11/3/2010 |
| Q: I have a problem with a briggs&stratton 14HP motor. Can you please tell me how to remove the starter ... A: >>You are not a Pain. LOL >>I would Prefer you Ask me Questions if you are in Doubt. >>That way you ... | |
| Scotts riding mower engine trouble | 11/3/2010 |
| Q: Scotts(J.Deere) riding mower. Tecumseh engine-cv16 Eng,ser.#2900602263 When first started,engine ... A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| Briggs motor | 11/3/2010 |
| Q: I have a briggs motor number is 261777 0130-01 9006253 put a new niddle in the carbarator steal ... A: >>Sorry for the Delay. >>They got behind in the Shop and I had to Help them Catch up. >>Did you Soak ... | |
| Tecumseh 3.5 vantage running problem | 11/2/2010 |
| Q: My lawnmower has this engine fitted and after about 30 minutes running starts to splutter and cough ... A: >>If you did Not Soak the Carburetor in Cleaning Solution, then the Carburetor may still be the ... | |
| 2.kva petrol generator | 11/2/2010 |
| Q: i have a 2 kva petrol generator which i have modified with a gas kit and using it on natural gas. 2 ... A: >>The Hard Kick is Usually caused by a Blown Head Gasket or a Damaged Flywheel Key. >>The Following ... | |
| mandrel assembly on Craftsman mower | 11/2/2010 |
| Q: I just replaced the mandrel on my Craftsman Model 917.273640 18.5 HP 42" mower. When I put the ... A: >>From your Description it Sounds like you have a New Mandrel that is Metric and the Pulley is SAE. ... | |
| B & S engine failure | 11/1/2010 |
| Q: Was using it yesterday and it briefly sounded a little different, then I heard something break, and ... A: >>From your Description it Sounds like the Connecting Rod may have Broken or there is a Problem with ... | |
| Yardman transmission | 11/1/2010 |
| Q: I just sent in a question. I think that I may have put the incorrect MTD part numberon my Yardman ... A: >>No Worries. It Happens all the Time. >>From your Description it Sounds like the Belt is Slipping ... | |
| Toro 38040 Snowblower | 11/1/2010 |
| Q: I saw a past thread about a toro snowblower 38040 not having spark. I am having the same problem. ... A: >>The Following is a Basic Instruction File I Made for Checking the Coil/Ign Coil/Magnetron/Armature ... | |
| Toro snowblower won't start. | 10/31/2010 |
| Q: I have a 98cc Toro Powerlite snowblower. It's about 5 years old and hasn't been ran in 2 years. I ... A: >>This Appears to be a 2 Cycle Engine on this Unit. >>Pour a Small Amount (1 table spoon) of ... | |
| Yardman transmission | 10/31/2010 |
| Q: I just sent in a question. I think that I may have put the incorrect MTD part numberon my Yardman ... A: >>I was Unable to Locate your Previous Question. >>Are you Sure you Sent it to me and Not 1 of the ... | |
| Wizard mower parts | 10/31/2010 |
| Q: My mother in law has a Wizard 30" rear engine riding mower, and the transaxle pully is bad, and the ... A: >>This is a Murray Manufactured Unit for the Wizard Brand. >>This Transaxle Pulley is a Murray Part ... | |
| Toro 521 Snowblower seized up | 10/31/2010 |
| Q: I told my neighbor that I'd take a look at his dead Toro 521 Snow thrower with a Tecumseh engine. ... A: >>From your Description, your Diagnosis is Right On as to the Broken Connecting Rod. >>There is ... | |
| Honda GC160 Engine | 10/30/2010 |
| Q: I had the carb replaced about 1 year ago, now its doing the same thing. At first it wouldnt start at ... A: >>If after Soaking and Cleaning a Second Time the Carburetor is still causing Problems, then ... | |
| Toro snowblower won't start. | 10/30/2010 |
| Q: I have a 98cc Toro Powerlite snowblower. It's about 5 years old and hasn't been ran in 2 years. I ... A: >>From your Description it Sounds like a Seized/Stuck Valve. >>Send me the Model Numbers Off the ... | |
| Briggs&Stratton 12.5 engine ring gear | 10/30/2010 |
| Q: I am replacing a ring gear on my Rally Ring mower, which has a12.5 Briggs& Stratton engine, Model ... A: >>Some Flywheels are Designed with a Pin and the Rivets and Others have No Pin. >>A Pin is Also used ... | |
| yard machine model 42a707 | 10/30/2010 |
| Q: I am trying to put my tension pulley for the drive belt back on and i just cant seem to get it ... A: >>The Model Numbers you gave me Look like a Briggs and Stratton Engine Model Number. >>For Better ... | |
| 2.kva petrol generator | 10/29/2010 |
| Q: i have a 2 kva petrol generator which i have modified with a gas kit and using it on natural gas. 2 ... A: >>Usually when an OHV Engine is Smoking White Smoke, it can be from One of the Following. >>The ... | |
| motorbike stator | 10/29/2010 |
| Q: how do you get a motocross bike stator to charge a battery and is it possible ? A: >>Most Motocross Cycle Engines have a Stator that will Light the Headlight but does Not have enough ... | |
| 17 hp twin cylinder briggs engine | 10/29/2010 |
| Q: the engine will crank when its cold. when it gets hot and you cut off the engine it will not crank ... A: >>Send me the Model and Type or Spec Numbers Off the Engine, Please. With these I can Locate the ... | |
| stihl fs 55 reply to your answer. | 10/28/2010 |
| Q: Hi again i tried taking off the muffler and starting the trimmer again still the same.I did notice ... A: >>Since you are Confident the Carburetor is Clean and Set Correctly, then >>Check the Flywheel Key. ... | |
| smoking | 10/28/2010 |
| Q: Just read answer given to a fellow about his Vanguard 14hp smoking. I have the same problem and am ... A: >>Not Realy. >>There is a Small Amount of Crankcase Pressure Required for these Small Engines to ... | |
| snow blower | 10/28/2010 |
| Q: I plan to get a snow blower but I do not know where to start. How big of a snow blower and what ... A: >>I Usually Do Not give Suggestions about Equipment, but I will make an Exception. >>There are Many ... | |
| 16.5 HP Honda lawn tractor | 10/28/2010 |
| Q: I have the above overhead cam tractor that began backfiring through the carburator.No power and new ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| John Deere SX75 | 10/27/2010 |
| Q: I have a well maintained JD SX75. Over the last several months, when riding it in "gears" 3 thru 7, ... A: >>Remove the Mower Deck Belt/s and Mower Deck from Under the Mower. >>Raise the Mower and Safetly ... | |
| Throttle issue with Kohler command 13 | 10/27/2010 |
| Q: i have a John Deer with a Kohler Command 13. Model #CV13s Family#SKH398V1G21ZB Spec#21509 Disp#398. ... A: >>The Following is an Instruction File I Made for Setting the Governor Arm Correctly. Any Input is ... | |
| stihl fs 55 reply to your answer. | 10/27/2010 |
| Q: Hi again i tried taking off the muffler and starting the trimmer again still the same.I did notice ... A: >>No Worries. It Happens. >>If you are Sure the Spark Plug is Firing, then the Carburetor Metering ... | |
| Poulan chainsaw | 10/26/2010 |
| Q: ..I have an older but wonderfull condition poulan 260 saw that does not run...Got it for free so I'm ... A: >>Sorry for the Delay. We have had High Winds and the Electic has been More Off the on and my ... | |
| John Deere SX75 | 10/26/2010 |
| Q: I have a well maintained JD SX75. Over the last several months, when riding it in "gears" 3 thru 7, ... A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| Swapping engine | 10/26/2010 |
| Q: Changing 20hp Kawasaki FD620D-AS17 to 27hp Kawasaki FD750D-S01. I want to put the 27 hp in a 98 ... A: >>Sorry for the Delay. We have had High Winds and the Electric has been More Off than on and All my ... | |
| JD 425 Stalling When Engaging Mower PTO | 10/26/2010 |
| Q: I just bought a 1997 JD 425 w/a FD620D-GS02 Engine. It has 650 hrs and is very clean. If I start it ... A: >>Sorry for the Delay. We have had High Winds and the Electric has been More Off than on and my ... | |
| Johnd Deere LX178 - pulley from drive shaft | 10/25/2010 |
| Q: I am replacing the engine in my JD LX178. All I have left is removing the pulley's and clutch from ... A: >>If I Understand you Correctly you are Asking How to Remove the Engine Drive Pulley that Pulls the ... | |
| Poulan chainsaw | 10/25/2010 |
| Q: ..I have an older but wonderfull condition poulan 260 saw that does not run...Got it for free so I'm ... A: >>Remove the Muffler and Look at the Inside of the Engine. >>Turn the Engine by Hand and Inspect ... | |
| B&S Pulsa-Jet Won't Fill | 10/25/2010 |
| Q: I have a 5hp B&S with a pulsa-jet carb (fixed jet). If I take carb off the fuel tank and manually ... A: >>Thanks. >>I wanted to Verify the Carburetor Style. >>The Brass Insert (Pickup Tube Extension) is ... | |
| Stihl 084 AV Carb adjustments ? | 10/24/2010 |
| Q: I have a very nice Stihl 084av chainsaw that had some carby issues. I pulled it apart and cleaned it ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Removal of starter motor | 10/24/2010 |
| Q: I have a problem with a briggs&stratton 14HP motor. Can you please tell me how to remove the starter ... A: >>Remove the 2 Screws that Hold the Starter Drive Cover onto the Blower Housing (Metal engine ... | |
| B&S Pulsa-Jet Won't Fill "reserve bowl" (Fuel Pump Won't Work) | 10/24/2010 |
| Q: I have a 5hp B&S with a pulsa-jet carb (fixed jet). If I take carb off the fuel tank and manually ... A: >>Send me the Model and Type or Spec Numbers Off the Engine, Please. With these I can Locate the ... | |
| Noma shifter | 10/24/2010 |
| Q: Hey John, Got a noma riding lawn mower from neighbor. it was changing gears fine but while riding ... A: >>Sorry for the Delay. I was trying to Locate these Model Numbers in my Manuals. >>On the Transaxle ... | |
| Honda EM500SX Generator will not come above idle | 10/23/2010 |
| Q: I have two Honda EM5000SX generators I purchased from an estate sale. They will start up and idle ... A: >>I haven't had any Luck Locating my Manual on this Unit, however, >>I have a Confermed Conference ... | |
| mower | 10/23/2010 |
| Q: A friend has a viking mt432t with a 12hp motor that is blowen can i put a 16hp motor in it from a ... A: >>Most 12HP and 16HP Engines have the Same Size Crankshaft Diameter and Length, so the Engines ... | |
| Swapping engine | 10/23/2010 |
| Q: Changing 20hp Kawasaki FD620D-AS17 to 27hp Kawasaki FD750D-S01. I want to put the 27 hp in a 98 ... A: >>Send me the Tractor Model Numbers, Please. With these I can Locate the Correct Manuals and Better ... | |
| JD 170 tractor - engine smoking heavily - Kawasaki engine | 10/22/2010 |
| Q: My tractor started spewing smoke from the exhaust while operating. At first it was light smoke, but ... A: >>Check the Head Gasket. >>A Blown Head Gasket will cause this Problem and Usually the Smoking ... | |
| Honda EM500SX Generator will not come above idle | 10/22/2010 |
| Q: I have two Honda EM5000SX generators I purchased from an estate sale. They will start up and idle ... A: >>Sorry for the Delay. I had to Assist the Shop Personnel Winterize Some of the Equipment and it ... | |
| gas line re-attachment | 10/22/2010 |
| Q: Re my McCulloch Pro-Scraper 28S trimmer; There are two lines come out of the fuel tank. I'm sure ... A: >>One Port is a Return to the Tank. >>The Inlet Port of the Carburetor is the Port Nearest the Flat ... | |
| Honda EM500SX Generator will not come above idle | 10/22/2010 |
| Q: I have two Honda EM5000SX generators I purchased from an estate sale. They will start up and idle ... A: >>The Solenoid is an Anti-Diesel and is Supposed to be in the Out Position when the Engine Switch is ... | |
| homelite chainsaw | 10/22/2010 |
| Q: John I just put a new carb kit in a walbro carb it ran good for a few minutes put the bar and chain ... A: >>If the Engine Ran Good with the Bar and Chain Off, then >>Adjust the Carburetor Mixture Screws. ... | |
| Poulan Pro mod. # pr1842stc wont start | 10/21/2010 |
| Q: I have a poulan pro mod.# pr1842stc. #1, It won't start because the brake/clutch pedal won't engage ... A: >>My Bad. I Simply Forgot about the Gnawing/Grinding Noise you Mentioned in the Original Question. ... | |
| Poulan Pro mod. # pr1842stc wont start | 10/21/2010 |
| Q: I have a poulan pro mod.# pr1842stc. #1, It won't start because the brake/clutch pedal won't engage ... A: >>Thanks for the Follow up. >>You are Correct about the Manuals. >>When you Adjust the Brakes like ... | |
| stihl fs 55 | 10/21/2010 |
| Q: I cannot get the trimmer to start if i pull it a few times i get a backfire if the choke is full ... A: >>This Problem is Usually caused by either the Exhaust Port and Muffler being Restricted by Carbon, ... | |
| Noma shifter | 10/21/2010 |
| Q: Hey John, Got a noma riding lawn mower from neighbor. it was changing gears fine but while riding ... A: >>Can you Locate the Model Numbers Off the Mower, Please. With these I can Locate the Correct ... | |
| Honda GC160 Engine | 10/21/2010 |
| Q: I had the carb replaced about 1 year ago, now its doing the same thing. At first it wouldnt start at ... A: >>From your Description it Sounds like the Carburetor may Require Another Soaking or the Fuel Pump ... | |
| 2 cycle blower problem | 10/20/2010 |
| Q: I have a Craftsman 37cc backpack blower model #636796912. Worked perfect for a couple years. Now it ... A: >>Does the Spark Plug Fire when this Happens? >>The Following is a Basic Instruction File I Made for ... | |
| Poulan Pro mod. # pr1842stc wont start | 10/20/2010 |
| Q: I have a poulan pro mod.# pr1842stc. #1, It won't start because the brake/clutch pedal won't engage ... A: >>You Adjusted the Brake Rod, Not the Brake Actuator. >>Return the Brake Rod to it's Original ... | |
| homelite super 2 chainsaw | 10/19/2010 |
| Q: have a saw that I just bought at a flea market put a trigger cable in the handle and cleaned the ... A: >>Thanks to the "All Mighty Dollar, Yen, Pound and ect", there is No Longer any Quality in ... | |
| stihl 036 | 10/19/2010 |
| Q: how do i disassemble the chain bar oiler on this particular model? A: >>If this is an Older Model Stihl, then you have to Split the Case to have Access to the Oiler. >>If ... | |
| JC Penny rototiller | 10/19/2010 |
| Q: John, Please help. I have an old JC Penny rototiller model number 3010. The motor is a Techumseh ... A: >>The Flywheel(Fan) has Magnets on it that are Set to Match the Crankshaft Throw and Correctly Time ... | |
| rear live axle on go kart | 10/18/2010 |
| Q: 5 inch center hole and i also need to know what parts i need for a band brake and a belt drive ... A: >>All Go-Cart Frames have the Mounting Brackets Attached (made to the Frame at the Factory). >>You ... | |
| JD 345 Lawn Mower Keeps Stalling | 10/18/2010 |
| Q: I have a JD 345 lawn tractor with a 20 hp Kawasaki engine (FD611V-BS01), it starts and runs great ... A: >>I Failed to Specifiy on the Pickup Tube; Look for a Pin Hole in the Pickup Tube as well as the ... | |
| craftsman snow thrower 536.886122 | 10/18/2010 |
| Q: Accidentaly sucked up a grease towel with the snowthrower. Was told by Sears that I needed an auger ... A: >>You can Use the Site Addys at this Site Addy; http://www.yetmans.mb.ca/antiques.html to Search and ... | |
| Briggs | 10/17/2010 |
| Q: Briggs and Stratton; Model 196432-0666-A1 code 9511291B I have the above engine on a BCS tiller. It ... A: >>You are talking about a Torx Socket. >>Some Small Engine OEM's have Started using Torx Head Bolts ... | |
| rear live axle on go kart | 10/17/2010 |
| Q: 5 inch center hole and i also need to know what parts i need for a band brake and a belt drive ... A: >>You will Require a Pulley Attached to the Drive Axle that Matches the Clutch Drive on the Engine. ... | |
| Briggs | 10/17/2010 |
| Q: Briggs and Stratton; Model 196432-0666-A1 code 9511291B I have the above engine on a BCS tiller. It ... A: >>It Sounds like the Carburetor Requires Soaking and Cleaning. >>The Following is a Basic File I ... | |
| Kohler Command CV125S S/N 2313909698 | 10/17/2010 |
| Q: 6-10 secs. 120lbs comp when cold. Runs fine and seems to restart faster on successive ... A: >>How Many Revolutions does the Engine make before Starting? >>From your Description it Sounds like ... | |
| Starting problems | 10/16/2010 |
| Q: I have a Sears Yard Vacum Model 247770550. I has a briggs & Stratton engine 1BSXS.1901VF 275228. I ... A: >>This Engine has an Ign Coil. >>From your Description it Sounds like the Coil Requires Replacing. ... | |
| 96 kawasaki fd590v on JD 345 | 10/16/2010 |
| Q: Do you know or can you find out what kind of thread is on the temperature sensor on the left side of ... A: >>The MM3 Markings Usually mean the Sensor Threads are Metric here in the US. >>I have again ... | |
| GC190 Honda Motor | 10/15/2010 |
| Q: This engine is being used on a log splitter - can you tell me what would cause an oil ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| oil under engine head | 10/15/2010 |
| Q: Have an old Tecumseh off Murray rider MID 70S? no numbers visible on blower housing think it may be ... A: >>On Some Ride On Mowers the Engine will Sling Oil from the Lower Crankshaft Seal and Deposit the ... | |
| oil | 10/15/2010 |
| Q: I have a craftsman lt4000 with a briggs & Stratton 12.5hp engine model #286707. I just purchased it ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| honda propane motor | 10/14/2010 |
| Q: I have a similar problem to what jerry has with his gx390.Except the one I have is a gxv390. Its on ... A: >>Sorry for the Delay. >>I Misplaced the Information you Required in my PC and just Located it. ... | |
| 96 kawasaki fd590v on JD 345 | 10/14/2010 |
| Q: Do you know or can you find out what kind of thread is on the temperature sensor on the left side of ... A: >>Sorry for the Delay. >>I Checked with Kawasaki and Confirm the 1/8"bspp Threads for the Sensor. I ... | |
| Weedeater BC24w won't run when hot | 10/14/2010 |
| Q: My Weedeater BC24W line trimmer starts easily from cold and runs OK on half choke until it warms up, ... A: >>From your Description it Sounds like a Restricted Muffler/Exhaust Port or the Rings/Jug/Cylinder ... | |
| chainsaw maccullock mac cat | 10/13/2010 |
| Q: have a saw that I just bought at a flea market put a trigger cable in the handle and cleaned the ... A: 1 - >>The Following is a Basic Instruction File for Locating the Cause/Cure for No Fire to Plug on ... | |
| chainsaw maccullock mac cat | 10/13/2010 |
| Q: have a saw that I just bought at a flea market put a trigger cable in the handle and cleaned the ... A: >>The Model Number for this Saw is 11-600160-02 Dated 07/90. >>I Spoke with the McCulloch Sales Rep ... | |
| honda propane motor | 10/13/2010 |
| Q: I have a similar problem to what jerry has with his gx390.Except the one I have is a gxv390. Its on ... A: >>According to my Honda Parts Supplier, the Regulator Replacement you Described will Operate as a ... | |
| chainsaw maccullock mac cat | 10/13/2010 |
| Q: have a saw that I just bought at a flea market put a trigger cable in the handle and cleaned the ... A: >>From your Description it Sounds like the Condensor is Bad and Requires Replacing. >>Some Model ... | |
| snowthrower doesn't throw snow | 10/12/2010 |
| Q: My snowthrower doesn't throw snow like it should. It starts up fine but the snow just falls out of ... A: >>No Worries. It Happens all the Time. >>You can View a Breakdown of this Unit at this Site Addy; ... | |
| 19 HP Briggs (No Spark) | 10/12/2010 |
| Q: Motor is on a Craftsman mower. I checked for spark with a screw driver in one of the cylinder spark ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Tecumseh | 10/12/2010 |
| Q: I have a Troy built Chipper-Vac, model #47282, Tecumseh H50- 65582V (B) 4059D. This is my second ... A: >>Any Engine that has the Same Crankshaft Diameter, Length and Keyway can be Used to Power this ... | |
| JD 345 Lawn Mower Keeps Stalling | 10/12/2010 |
| Q: I have a JD 345 lawn tractor with a 20 hp Kawasaki engine (FD611V-BS01), it starts and runs great ... A: >>Does the Engine Turn Over Easily when this Happens or Does it Turn as it Does when the Engine is ... | |
| snowthrower doesn't throw snow | 10/11/2010 |
| Q: My snowthrower doesn't throw snow like it should. It starts up fine but the snow just falls out of ... A: >>That is the Series Model Number. >>I Require the Actual Unit Model Numbers. >>The model and serial ... | |
| Tecumseh | 10/11/2010 |
| Q: I have a Troy built Chipper-Vac, model #47282, Tecumseh H50- 65582V (B) 4059D. This is my second ... A: >>I Tell my Customers that the Repairs should Never Cost more than Half of what a New Unit would ... | |
| snowthrower doesn't throw snow | 10/11/2010 |
| Q: My snowthrower doesn't throw snow like it should. It starts up fine but the snow just falls out of ... A: >>There are Many Different Styles of Snow Throwers on the Market and they have Different Components ... | |
| Engine Repair | 10/10/2010 |
| Q: John this is hunter again, would you be willing to sell that engine. Or do you know where i can get ... A: Welcome Back Hunter: >>I wouldn't mind Selling you the Engine, but it has been Parted Out and all ... | |
| carb settings | 10/10/2010 |
| Q: Mccullough weed trimmer needs factory settings for the carb what are they and what is the best way ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Husqvarna Zero turn with Kohler engine | 10/10/2010 |
| Q: The unit is 10 years old and only used on my 5 acre lot. That being said, it is maintained very ... A: >>You and I need to Do a Diagnostics on this Unit. >>Send me the Model and Type or Spec Numbers Off ... | |
| Troy Bilt Junior Tiller | 10/10/2010 |
| Q: My tiller runs Ok at low speeds but if I try to run at a high speed the engine gets hot and seizes ... A: >>Go to this Site Addy, http://www.jackssmallengines.com/help.cfm/ and Select "Shop Online Parts ... | |
| mulching | 10/9/2010 |
| Q: i have a craftsman 32cc leaf blower/mulch/vac which for some reason does not mulch, it blows and ... A: >>A Model Number would Help me Assist you Better. Go to this Site Addy, http://www3.sears.com/ and ... | |
| Oily Spark plug | 10/9/2010 |
| Q: I have a Craftsman LT 1000 mower with a CRAFTSMAN I/C 17.5 HP OHV (BRIGGS & STRATTON)motor. It has ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| Honda GCV lawn mower repair | 10/9/2010 |
| Q: My Honda lawn mower wont stay in gear to cut grass. When you engage the right side lever to start ... A: >>Since this is a Honda, you can Use this Site Addy; http://www.honda-engines-eu.com/en/welcome.html ... | |
| sthil chainsaw ms210 | 10/8/2010 |
| Q: sorry I sent first half to wrong john. Problem is ms210 saw will not start will not even fire once. ... A: >>What is the Compression? >>Add a Small Amount of Straight 2 Cycle Oil to the Cylinder throught the ... | |
| JD317 Mower | 10/8/2010 |
| Q: This engine is on your log splitter. We can get it started but it will not stay running. We have ... A: >>If the Engine is Shutting Down like you have Turned Off the Key, then >>Check the Connection where ... | |
| Engine Repair | 10/8/2010 |
| Q: John, this is hunter, i just had a few questions about my engine on my go cart. I have a what is ... A: >>From your Description (and the Fact that this is a Tecumseh Engine that was Run with Low Oil ... | |
| harry lawnmower | 10/7/2010 |
| Q: How do you adjust the tickover speed on a honda gcv160 5.5 hp.lawnmower engine please, when i pull ... A: >>The Idle RPM is 1700 + or - 150 RPM. >>Since this is a Honda, you can Use this Site Addy; ... | |
| B&S 7.0 OHV engine | 10/7/2010 |
| Q: This engine is on your log splitter. We can get it started but it will not stay running. We have ... A: >>I am Glad the Other Engine is Running Correctly for you now. >>From your Description it Sounds ... | |
| Oily Spark plug | 10/6/2010 |
| Q: I have a Craftsman LT 1000 mower with a CRAFTSMAN I/C 17.5 HP OHV (BRIGGS & STRATTON)motor. It has ... A: >>Send me the Model and Type or Spec Numbers Off the Engine, Please. With these I can Locate the ... | |
| Toro S-620 Snowblower | 10/6/2010 |
| Q: I recently inherited my Dad's property. I found a Toro S-620 snowblower (hasn't been used in over ... A: >>These Units came with either a 2 Cycle or a 4 Cycle Engine. >>Send me the Model and Type or Spec ... | |
| briggs & stratton portable electric generator | 10/5/2010 |
| Q: I purchased a portable generator two years ago and have had it in storage...brand new...I have since ... A: >>Remove the Spark Plug and Attempt to Turn the Engine with the Starter. >>Will the Engine Turn ... | |
| deere 345 no spark, but coils hot, key off | 10/5/2010 |
| Q: Have a FD611D 20hp Kawasaki in a Deere 345 tractor. No spark. Went through the procedures in the ... A: >>From your Description it Sounds like the Ign Switch is Shorted and Requires Replacing or there is ... | |
| B&S 7.0 OHV engine | 10/5/2010 |
| Q: This engine is on your log splitter. We can get it started but it will not stay running. We have ... A: >>Did you Soak the Carburetor or Use Spray Cleaners? >>The Following is a Basic File I Made for ... | |
| Honda GCV160 sudden stop | 10/4/2010 |
| Q: My mountfield mower struck a metal object buried in the ground and stopped violently with a loud ... A: >>Usuall if the Timing Belt Jumps the Engine may Run, but will have No Power or Usually will Not ... | |
| Overheating battery cables | 10/4/2010 |
| Q: I have a yardman ride on mower its not turning over properly and the battery leads are overheating ... A: >>If this Mower has an OHV Engine, then Set the Valve Clearances. >>From your Description it Sounds ... | |
| Kohler KT17s-spec# 24223 | 10/4/2010 |
| Q: Not a question at this time, but rather a thank you for invaluable owner and service manual links ... A: >>I am Glad the Links and Information I Provide can Assist you and Others. >>Till Next Time. May All ... | |
| greyhound 6.5hp idle to high | 10/4/2010 |
| Q: i have a go-kart with a brand new greyhound 6.5hp engine on it and when you do not press the gas it ... A: >>Are you Saying that when you Start the Engine it is Idling too High? >>If Yes, then you need to ... | |
| fixing my lawn mower | 10/3/2010 |
| Q: hope you can help me to fix my lawn mower, it start and run for a while (for a few seconds) then it ... A: >>From your Brief Description it Sounds like the Carburetor Requires Soaking and Cleaning. >>The ... | |
| Honda GCV160 sudden stop | 10/3/2010 |
| Q: My mountfield mower struck a metal object buried in the ground and stopped violently with a loud ... A: >>If this Engine has a Belt, then the Engine May have Jumped the Belt or the FLywheel Key May be ... | |
| Power loss after 15 min normal operation | 10/3/2010 |
| Q: my mini roto tiller -- honda engine ( GX25 ) , tiller ( FG110 ) , about 5yrs old ... worked fine ... A: From your Description it Sounds like the Carburetor Requires Soaking and Cleaning. >>The Following ... | |
| Pull cord doesn't turn engine | 10/2/2010 |
| Q: John, I have a TroyBilt chipper shredder that has a B&S Moddel 204412-0417E1 engine. Was happily ... A: >>Since you are Doing it the Way you are, I Suggest you Use Liquid Wrench to throughly Soak the ... | |
| Pull cord doesn't turn engine | 10/2/2010 |
| Q: John, I have a TroyBilt chipper shredder that has a B&S Moddel 204412-0417E1 engine. Was happily ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| snowblower part | 10/2/2010 |
| Q: It has the 8hp Tecumseh engine.The Model of the blower is C950-52677-8.I'm having a hard time ... A: >>You will have to Search for this Style Alternator at the Companies and Sites that have the ... | |
| snowblower part | 10/1/2010 |
| Q: It has the 8hp Tecumseh engine.The Model of the blower is C950-52677-8.I'm having a hard time ... A: >>What Add-on Alternator is this Unit Using? >>Thanks. Respectully John >>PS: I am Allowed to ... | |
| Golden Boy Edger/Briggs & Stratton KS71 | 10/1/2010 |
| Q: What type oil does this edger require? A: >>ALL 4 Stroke Engines use SAE 10W30 Automotive Engine Oil. >>I Use SAE 10W30 Synthetic Engine Oil ... | |
| Coleman Generator | 10/1/2010 |
| Q: I have a Coleman Powermate 5000 generator powered by a 10 HP Tecumseh engine. I bought the machine ... A: >>This Problem is Usually caused by a Blown Capicitor or Condensor. >>If you have Electrical ... | |
| Engine won't stay running | 9/30/2010 |
| Q: Sears Best Blower/Vac Mulcher - in other words, a leaf blower. 32CC 170MPH 360CFM SN: 95268N03717 ... A: >>From your Description it Sounds like the Exhaust Port (Muffler Included) is Restricted or the ... | |
| Replacing Starter Gear on Briggs & Stratton Engine for MTD Lawn Tractor | 9/30/2010 |
| Q: This is a follow-up question from an answer you gave last year to someone with a similar problem. ... A: >>Remove the Starter from the Engine and then Replace the Starter Drive Gear. >>Make Sure the Bevel ... | |
| 1638HS Sabre 1997 Hydro transmission | 9/30/2010 |
| Q: i have an aging '97 Sabre 1638HS. Runs great but this year, it started "slippiing" when trying to ... A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| Murray Push Mower | 9/29/2010 |
| Q: We have a Murray 22" push mower with a Briggs & Stratton engine. The bracket on the stop engine ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| lawnboy self propelled | 9/29/2010 |
| Q: I have a lawnboy 10682 insight. The self propel feature doesn't work well. It makes a bad noise and ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| LS1000 craftsman w/ 17.5 briggs | 9/29/2010 |
| Q: LS1000 42" deck,OHV 17.5 briggs. Model# 917.272673 not sure if you need the mode, type, and code ... A: >>I am Glad I was able to Assist you in Solving this Problem. >>For some Reason some of the OHV ... | |
| Scotts riding mower | 9/29/2010 |
| Q: I have a 25HP Scotts riding mower. When I start it, it runs wide open. I'm guessing that my problem ... A: >>Follow the Instructions for Setting the Governor Arm. >>Since moving the Governor Arm Does Change ... | |
| HOFFCO HB-250 BLOWER | 9/28/2010 |
| Q: I HAVE HOFFCO HB-250 LEAF BLOWER.IT WAS A GREAT MACHINE TILL YESTERDAY .I STRIPPED THE ENGINE DOWN ... A: >>I can/will List the Parts for sale for you for my Customers and Local Residents, but you might ... | |
| LS1000 craftsman w/ 17.5 briggs | 9/28/2010 |
| Q: LS1000 42" deck,OHV 17.5 briggs. Model# 917.272673 not sure if you need the mode, type, and code ... A: >>You are Correct in Thinking the Valve Clearances are Incorrect and Require Setting. >>When the ... | |
| kawasaki engine | 9/28/2010 |
| Q: I have an older kawasaki stationery engine model kf 100D it states on the model plate that it is 10 ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Scotts riding mower | 9/28/2010 |
| Q: I have a 25HP Scotts riding mower. When I start it, it runs wide open. I'm guessing that my problem ... A: >>When you Move the Governor Control Arm, Does the Engine Speed Change? >>For Better Assistance, ... | |
| John Deere self propelled lawnmower | 9/27/2010 |
| Q: i have a John Deere self propelled mower 190cc 6.75HP product ID GXJS20A133164 model: JS20 ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| rod to crank assembly | 9/26/2010 |
| Q: I am putting a new rod to the crank on a Briggs and Stratton motor 12.5 hp and need to now which way ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| murry 12.5 want start | 9/26/2010 |
| Q: my Murray 38 in cut 12.5 horse as a plug on the side of the motor and when its plug up it want ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| briggs &stratton model number 31m444-0234e1 | 9/26/2010 |
| Q: I changed the reed on the crankcase breather while assembling the engine i set the airgap at .010". ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| carburator breather assembly for a briggs and stratton motor | 9/24/2010 |
| Q: I have a Briggs and Stratton motor model 287707 type 1224-e1 code 9710102D. My kids turned my mower ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| JD 322 brake issue | 9/21/2010 |
| Q: I have a John Deere 322 garden tractor and the brake pedal for the left side stays down when ... A: Helo Blaine: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| Chainsaw won't turn over correctly after stalling. | 9/21/2010 |
| Q: I'd welcome any suggestions or help in diagnosing a problem. The engine fault is on a Gardenline ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Briggs & Stratton Pro Classic 3500 watt generator | 9/20/2010 |
| Q: I have a Briggs Pro Classic 3500 Watt generator with an Intek 206 engine (the engine cover has the ... A: >>Disconnect the Oil Sensor Lead/s and Check for Fire at the Spark Plug. >>If the Plug is Now ... | |
| Honda blade clutch noise at idle | 9/18/2010 |
| Q: At idle, my Honda HRM215SXA mower makes a loud, whirring noise, much like a dry bearing. The noise ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Craftsman weed-whacker mod. 358791050 | 6/8/2010 |
| Q: I'm trying to access the pully start mechanism, to replace the rope which broke, in this unit but ... A: >>It's a #15 Torx if I'm Not Mistaken. >>The Clutch is Hand Tightened. >>The Engine Rotation will ... | |
| Generac Power Washer engine | 6/8/2010 |
| Q: Generac-160, 5.5 hp engine will start but only run for a short time (approx. 1 min.)when stone cold. ... A: >>Did you Gap the Ign Coil Correctly? >>***Anytime a Magnet that is Set to the Correct Distance from ... | |
| Honda Harmony 1011 | 6/8/2010 |
| Q: I have a Honda Harmony 1011 that is probably about 15 years old. While mowing recently, it just ... A: >>You can View a Breakdown/IPL at this Site Addy, http://www.emerichsales.com/ and Select Honda in ... | |
| JD 445 - remove camshaft | 6/8/2010 |
| Q: The gear on the camshaft is plastic and the gear is striped. I have the front open, I need to know ... A: >>The Heads Do Not have to be Removed. >>You can Loosen the Rocker Arms and Remove the Push Tubes ... | |
| Murray mower brake | 6/7/2010 |
| Q: I have seen past questions regarding adjusting the brakes on a Murray mower, but I have not seen ... A: >>The Problem can be that the Disc Pads Require Replacing or the Brake Adjuster Nut may Require ... | |
| Mikuni carbureto problem | 6/7/2010 |
| Q: I have a 1986 Polaris 250 Trail Boss and it broke down and wouldn't start, so I took the carburetor ... A: >>Is the Plug Wet or Dry when this Happens? >>Is the Plug Firing when this Happens? >>Will the ... | |
| Kohler mower rope won't rewind | 6/7/2010 |
| Q: I have a Husqvana mower with a Kohler Courage XT-7 vertical crankshaft engine. The starter rope ... A: >>From your Description it Sounds like the Recoil Spring Broke when it Back-lashed from the Rope ... | |
| Lawn Tractor 17.5 HP Briggs & Stratton | 6/7/2010 |
| Q: I have a 2001 Yardman bt MTD with a Briggs & Stratton 17.5 HP motor Model # 13AD624G401 It will turn ... A: >>From your Description it Sounds like the Carburetor has a Restriction in the Jets. >>I Suggest you ... | |
| Craftsman engine floods/won't start when hot | 6/6/2010 |
| Q: I found that you had responded to an identical question on the exact same Craftsman engine ... A: >>From your Description it Sounds like the Carburetor Needle Valve is Sticking. >>I Suggest you ... | |
| Generac Power Washer engine | 6/6/2010 |
| Q: Generac-160, 5.5 hp engine will start but only run for a short time (approx. 1 min.)when stone cold. ... A: >>Sorry for the Delay. My PC Crashed and it Took a while to get it Up and Going again and its Still ... | |
| HONDA GX340 GENERATOR | 6/6/2010 |
| Q: I CLEANED MY CARB AFTER THE GEN WOULD NOT START;HOWEVER, I HAD A PART THAT FELL IN TO MY HAND THAT I ... A: >>Sorry for the Delay. My PC Crashed and it Took a while to get it Up and Going again and it Still ... | |
| Craftsman weed-whacker mod. 358791050 | 6/6/2010 |
| Q: I'm trying to access the pully start mechanism, to replace the rope which broke, in this unit but ... A: >>Sorry for the Delay. My PC Crashed and it Took a while to get it Up and Going again. >>On Some ... | |
| Head gaskets | 6/6/2010 |
| Q: My son asked me if there was any way to make a head gasket for a lawnmower. My answer: I made a ... A: >>This Question brings back Memories from Long, Long ago. LOL. >>I used to Make Head Gaskets from ... | |
| john deere 445 runs rough | 6/5/2010 |
| Q: my dad has jd445 and cam went out a few years ago.had dealer fix and also new fuel pump and water ... A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| Lawn boy coil part number | 6/5/2010 |
| Q: What is the part number for a coil for 1988 F100 Lawnboy engine? I have a Lawnboy model 5278. ... A: >>The Coil for this Engine (1988 F100) is 100-2949 (Replaces 681578) and is Listed for $74.92us. ... | |
| Murray lawnmower help | 6/5/2010 |
| Q: Can you please help? A: >>You can View a Breakdown of this Mower At this Site Addy; ... | |
| Homelite UT-20601c | 6/5/2010 |
| Q: I saw where you answered in detail some carburation questions elsewhere in this forum about this ... A: >>For an Owners Manual you wil have to Contact Homelite. >>You can use this Site Addy; ... | |
| CH18S Oil Pressure | 6/5/2010 |
| Q: Model:CH18S Spec. No.: 62509 S/N:2413302087 With 10W40 oil at cold start it is 42 psi, during use ... A: >>As Long as you have at east 20 PSI After Starting the Engine when it has Set Unused for at Least 2 ... | |
| 20hp briggs intek | 6/4/2010 |
| Q: I have a 20hp Briggs intek on a dixon ztr mower. After mowing for about four hours I parked in the ... A: >>Is the Throttle Cable Moving the Throttle Control Bracket? >>Is the Throttle Control Bracket ... | |
| murray 309304x8e 2002 model year | 6/4/2010 |
| Q: I am having an issue where I can only start the mower by having the black wire that comes out of the ... A: >>From your Description it Sounds like a Bad Safety Switch, a Bad Connection in the Safety System or ... | |
| HONDA GX340 GENERATOR | 6/4/2010 |
| Q: I CLEANED MY CARB AFTER THE GEN WOULD NOT START;HOWEVER, I HAD A PART THAT FELL IN TO MY HAND THAT I ... A: >>Can you Explain what you mean by "Holding the Butterfly Plate in Place", Please. >>Thanks. ... | |
| HONDA FG110 Mini-Tiller | 6/4/2010 |
| Q: I purchased a honda mini-tiller this spring to cultivate my garden. When I purchased it,it ran fine. ... A: >>I Suggest you Return the Unit or have it Repaired Under Warranty. >>It may be the Rings or the ... | |
| Dead Engine | 6/4/2010 |
| Q: Murray riding mower 12.5 hp/40” cut, model 40631A, purchased 2/92. B & S engine, model 286707. I ... A: >>Lets Check something else First, before we Check Any Switches. >>Check the Charging Voltage from ... | |
| gx95 j.deere | 6/3/2010 |
| Q: john its me again,the fuel pump diaphragms,where can i buy them? and where can i get the mr. gasket ... A: >>The Diaphragms should be Available from your Local Small Engine Service Center or you can Get them ... | |
| gx95 | 6/3/2010 |
| Q: After mowing for a length of time and shutting down,I can't restart the mower. It's like there is no ... A: >>From your Description it Sounds like the Starter Relay (Not Solenoid) is Heating up and Requires ... | |
| Peerless Transaxle problems | 6/3/2010 |
| Q: I have a 12 hp Simplicity tractor with a Peerless 801-019C transaxle. The number on the i.d. tag ... A: >>Sorry for the Delay. My PC Crashed and it Took a while to get it Up and Going again. >>From your ... | |
| weedwacker ignitor module | 6/3/2010 |
| Q: I need to replace ignitor module on Craftsman 32cc brushwhacker model # 358.795810 My problem is ... A: >>Sorry for the Delay. My PC Crashed and it Took a while to get it Up and Going again. >>To View a ... | |
| MTD Variable Speed Pulley | 6/3/2010 |
| Q: I am trying to repair my sisters MTD Riding Mower. It is a 1996 year model. The model number is: ... A: >>Sorry for the Delay. My PC Crashed and it took a While to get it Up and going again. >>From your ... | |
| tiller | 6/2/2010 |
| Q: I have an old tiller a magna hustler model#500520 serial#2079 I Need a sprocket and a drive chain ... A: >>Usually the Drive Sprockets and Chains can be Matched up to Operate on Different OEM and Model ... | |
| Runs rough, surges when hot | 6/2/2010 |
| Q: Briggs 402707, 1205 01. Engine starts and runs fine for about 45 min. then begins to surge and run ... A: >>The Following is a Basic Instruction File I made for this. Any Input is Appreciated. I Usually ... | |
| Dead Engine | 6/2/2010 |
| Q: Murray riding mower 12.5 hp/40” cut, model 40631A, purchased 2/92. B & S engine, model 286707. I ... A: >>No Worries. This Happens all the Time in the Shop. LOL. You can View a Breakdown of this Unit at ... | |
| peerless tranny | 6/2/2010 |
| Q: mr. bridges thank you for taking the time to help me.you had sent me a reply to try and get back to ... A: >>Thanks for getting Back to me. >>As Usual I could Not Locate Our Previous E-mails. >>The ... | |
| B&S 18.5 OHV engine, 39P777 | 6/2/2010 |
| Q: My mower stopped running and I found the the top rocker arm completely disengaged from the valve. ... A: >>Sometimes when a Push Tube Jumps Out as you Described, the Flywheel Key can become Damaged and ... | |
| John Deere RX95 | 6/1/2010 |
| Q: It seems every spring I have troubles starting this unit. (and nothing runs like a deere?) I've ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Front Wheel Drive Sears-Honda Wheels Lock-Up In Reverse | 6/1/2010 |
| Q: I have a Sears-Honda 07137683000 front wheel drive self-propelled lawn mower that the front wheels ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| How does it generate electricity? | 6/1/2010 |
| Q: I just bought my first riding mower, more or less for something to tinker with. This is an old ... A: >>The Stator/Charging Coils are Located Under the Flywheel. >>You can View a Breakdown/IPL of this ... | |
| no spark in Toro Mower | 6/1/2010 |
| Q: I have a Toro Personal Pace mower Model#20017. There is no spark. Changed the plug, but still ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| B&S 80202-2324-01 - How do I prime it? | 6/1/2010 |
| Q: Have a B&S 80202 Type 2324-01 Code: 87110903 and love it. Choke and running controls are on handle ... A: >>If you have to Pull the Recoil Starter MORE THAN 5 Times, then there is a Carburetor Problem for ... | |
| cv23s running rough (cam problem +?) | 6/1/2010 |
| Q: Another question on the CV23S Spec: 75559 S.N.: 3225503391. This is the one that you thought might ... A: >>I Suggest you Go Ahead and Replace the Cam and Lifters. >>By Powering Down and then Quickly ... | |
| Honda Blade Brake | 6/1/2010 |
| Q: Please read and I hope all infomation is here. Honda Harmony 215 HRB-215-FG MZBA-6214016 5.0 ... A: >>I am Sorry you had Trouble with the First Expert, but Thanks for Trying again. >>You can View a ... | |
| Repairing a steering problem Craftsman tractor | 6/1/2010 |
| Q: ..hoping you can help. The steering went in my craftsman lawn tractor model 917.270810. I was ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Homelite String Trimmer | 6/1/2010 |
| Q: I have a Homelite Phantom SS UT20682 String Trimmer and the string head is worn out. Can you provide ... A: >>The Following is an Instruction File I made for this Problem. Any Input is Appreciated. >>Looking ... | |
| Dead Engine | 5/31/2010 |
| Q: Murray riding mower 12.5 hp/40” cut, model 40631A, purchased 2/92. B & S engine, model 286707. I ... A: >>From your Description it Sounds like a PTO Problem. >>If the PTO has Shorted the Starter Solenoid ... | |
| john deere lx176 wont start | 5/31/2010 |
| Q: I changed the battery, it just wont turn over. any ideas? A: >>By "Turn Over", do you mean the Engine Does Not Turn at All or is the Engine Turning but Not ... | |
| Honda HRA215SX Mower Clutch Cable Install | 5/31/2010 |
| Q: John, I have a very similar question to the one Josh posted on May 6/10 for his Honda Harmony ... A: >>Sorry for the Delay, but I wanted to Check with the Honda Rep before I Answered. >>There is Not an ... | |
| Homelite Trimmer | 5/31/2010 |
| Q: I have a Homelite MightLite 26cc trimmer. The model number on the engine is UT21506 and it was ... A: >>From your Description it Sounds like the Air Mixture Screw for the High RPM's Requires Setting, ... | |
| john deere lawnmowner 425 | 5/30/2010 |
| Q: where is the fuel pump location A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| Lawn Tractor Will Not Start | 5/30/2010 |
| Q: I have a Craftsman Model 917.254940 Lawn Tractor. The Tractor has a few years on it (purchased in ... A: >>From your Description it Sounds like a Safety Switch has a Bad Connection, is Going Bad or there ... | |
| JD 160 | 5/30/2010 |
| Q: I have a JD 160 that was also handed down to me like one of your previous questions. The problem ... A: >>The Following is a PTO Test File I made. Any Input is Appreciated. **If you have an Ohmmeter, ... | |
| riding lawnmower | 5/30/2010 |
| Q: John, My riding lawnmower starts but won't move forward or backwards. It worked fine last week. I ... A: >>From your Description it Sounds like an Idler Pulley has Frozen and Requires Replacing or a Belt ... | |
| primer bulb | 5/30/2010 |
| Q: I have a Weedeater brand weedeater that wont start. When I pump the primer bulb it sucks it flat and ... A: >>From your Description it Sounds like this Primer Bulb is a Primer Bulb Assembly with a Check Valve ... | |
| replace piston on a 9 hp techumseh | 5/30/2010 |
| Q: I have a 9 hp techumseh engine on a craftsman snowblower. went to start it and it ran for a few ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| return question | 5/29/2010 |
| Q: i submitted a question on a noma lawn tractor on 5-18-2010 and received a response on 5-18-2010.noma ... A: >>Thanks for the Reference Date. >>From your Last E-mail and using this E-mail, I See this is a ... | |
| Kohler Engine Running Rough | 5/29/2010 |
| Q: One of the things that drew me to you when I first found this site was the blessing you asked for ... A: >>Thanks. I am Also Pleased to Hear You and Yours Believe and I am Sure Blessed by the All Mighty. ... | |
| tecumseh 143.029003 | 5/29/2010 |
| Q: I recently acquired a 9hp snowblower with a tecumseh engine 143.029003. There is a wire dangling. ... A: >>Thanks for the Picture. >>From your Description and After Viewing the Picture you Included it ... | |
| Cub Cadet LT1018 cranks but won't start | 5/29/2010 |
| Q: I have a 6 year old Cub Cadet LT1018 with the B&S ELS500 18.5hp engine; it's a replacement (the ... A: >>From your Description it can be the Coil going Bad or 1 of the Safety Switches has a Bad/Loose ... | |
| MTD Yardmachine 13AC762F729 leaking grease | 5/28/2010 |
| Q: John, do you have advice on replenishing the grease and sealing a leak on the transmission / axle / ... A: >>I have had Several of the Newer Transaxle in the Shop for the Same Problem. >>Usually I Split the ... | |
| stihl 032av chainsaw | 5/28/2010 |
| Q: IN regards to a 3-6-10 reply by Paul in regards to a question regarding an after market coil for a ... A: >>Hello Jim: >>This Ign Module is Designed to Replace the Point Set Only and Not the Coil. >>I am ... | |
| Briggs & Stratton 15 hp | 5/28/2010 |
| Q: John, I am sorry to have been so unclear in my last questions and this is a fundamentally dumb one. ... A: >>No Worries. >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| black primer bulb | 5/28/2010 |
| Q: where could i find a black primer bulb lawboy silver series model 10323 ser 200007891 please need ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| Kohler Engine Running Rough | 5/28/2010 |
| Q: I have a 60" eXmark TTHP with a Kohler 23 hp engine on it. The engine specs are: Kohler 23hp CV23S ... A: >>1- Check the Carburetor Solenoid. >>The Backfiring Tells me that the Solenoid is Not Operating as ... | |
| belt replacement | 5/27/2010 |
| Q: Please tell me how to replace the belt on my Honda self propelled lawnmower A: >>Depending on the Model of the Mower will Determine how to Replace this Belt. >>For Better ... | |
| Lawnmower discharges battery | 5/27/2010 |
| Q: I have an older craftsman riding mower with a 16 hp Kohler engine. It was running fine, my wife said ... A: >>From your Description it Sounds like the Stator/Charging Coils or the Voltage Regulator (if ... | |
| B&S 15 hp white smoke | 5/27/2010 |
| Q: John, Thank-you so much for the prompt reply I think you may have misunderstood the first question ... A: >>The Steel Push Tube is for the Exhaust and the Alloy Push Tube is for the Intake. >>As Always, If ... | |
| carb linkage connection | 5/26/2010 |
| Q: I took my carb apart to clean it and forgot how to connect the two linkage rods. I have tryed ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Montgomery Ward tiller | 5/26/2010 |
| Q: It has some rust but is otherwise intact and runs well. I have someone who wants to buy it from me ... A: >>The Model Number is for a Gilson Manufactured Unit. >>In 1988 Gilson was Acquired by LAWN-BOY. In ... | |
| 1. I need a source for a coil to fit a Kohler Electric Plant cir 1949, model 350 C21K7 SN 148508 | 5/26/2010 |
| Q: I'm looking for a coil to bring life back to this engine. 2. Where can I contact builder of a ... A: >>I Contacted Kohler this AM and they should be Back in Touch with me within 72hrs with a Response ... | |
| STX38 John Deere | 5/26/2010 |
| Q: I have a John Deere STX38 lawn tractor, with a Kohler Command 13 engine with a black deck. Model # ... A: >>You can View a Breakdown of the Engine at this Site Addy; http://www.kohlerplus.com/login.asp (IE5 ... | |
| riding mower engine probs | 5/26/2010 |
| Q: I have a 12/36 Duralast. Two questions: 1.) I rebuilt the carb, and when placing that little while ... A: >>THINK SAFETY: Always Remove the Spark Plug Wire/s from the Spark Plug/s and Tie Away from the ... | |
| Craftsman Tractor starves for fuel | 5/26/2010 |
| Q: I have a Craftsman LT2000 Lawn Tractor with a 17hp Kohler engine. Starts and runs fine, plenty of ... A: >>THINK SAFETY: Always Remove the Spark Plug Wire/s from the Spark Plug/s and Tie Away from the ... | |
| Kohler | 5/25/2010 |
| Q: John You ansered my question about the breakdown of my engine,except the two places you told me to ... A: >>I Hope all is Well with You and Yours. >>I Spoke with Kohler this AM and they Do Not have the ... | |
| Kawasaki FC420V Mower | 5/25/2010 |
| Q: received your response. Thanks. The model # I found is : 930001. Hope that helps. As a reference the ... A: >>Kawasaki is the Engine OEM. >>Who is the Mowers OEM? >>Kawasaki makes Handhelp Outdoor Products ... | |
| belt | 5/25/2010 |
| Q: need belt for Agway LT10/38 the deck belt mod#134697019 Serial#21 055 6132 A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| B&S 15 hp white smoke | 5/25/2010 |
| Q: John, Thank-you so much for the prompt reply I think you may have misunderstood the first question ... A: >>I am Sorry if I Misunderstood your Question. >>The Breather you are Asking about can be Cleaned by ... | |
| briggs and stratton 3-1/2hp engine | 5/25/2010 |
| Q: Model 92908,type-1224-01, code-7202225 The mower has been giving excellent service for years but ... A: >>No Worries. You are Welcome and Thanks for the Ratings. >>From your Description it Sounds like the ... | |
| Craftsman Tractor starves for fuel | 5/25/2010 |
| Q: I have a Craftsman LT2000 Lawn Tractor with a 17hp Kohler engine. Starts and runs fine, plenty of ... A: >>Send me the Model and Type or Spec Numbers Off the Engine and the Unit/Mower Model Numbers, ... | |
| Poulan Pro Blower | 5/24/2010 |
| Q: My Model SM400 gas blower has become very hard to start and when it does start will not stay running ... A: >>The Following is a Basic Instruction File for Doing a Diagnostic on the Engine for this Problem. ... | |
| LT 120 | 5/24/2010 |
| Q: My John Deer LT120 started smoking and is using oil. It still cuts well but have to keep a check on ... A: >>According to the Breakdown, this is an OHV Engine. >>I Suggest you Check the Head Bolts and make ... | |
| Briggs & Stratton 12.5 Model 289707 | 5/24/2010 |
| Q: I have a 12.5 HP Briggs & Stratton OHV model 289707. It started blowing blue smoke and cut off at ... A: >>Check the Head Gasket First. >>On the OHV Engines the Head Gasket will Blow Between the Push Tube ... | |
| Kohler | 5/24/2010 |
| Q: Mr.President :-) Hi again John...... Hey....I bought a Kohler CH270-0011 for my Go kart.I need a ... A: >>Have you Tried these Sites; >>1- www.outdoordistributors.com >>2- ... | |
| B&S 15 hp white smoke | 5/24/2010 |
| Q: John, I am following up on the B&S 15 hp white smoke question of 5/17/10. I have cleaned the carb ... A: >>You can View a Breakdown/IPL of the Engine at this Site Addy; ... | |
| Troy Bilt Tiller Will NOT Stay Running | 5/23/2010 |
| Q: Troy Bilt Super Bronco 16" 208cc Rear Tine Tiller, model #: 21C-65M1011, comes with a Troy Bilt ... A: >>You can View a Breakdown/IPL of this Unit at this Site Addy, ... | |
| gas in oil in lawn tractor motor | 5/23/2010 |
| Q: I have a 2001 John Deere LX255 lawn tractor with a 15 HP B%26G engine. I started it today, started ... A: >>The Following is an Instruction File I Made for the Gas Contamination of the Crankcase Oil and/or ... | |
| height adjustment dial on a JD GX345 will not work | 5/23/2010 |
| Q: I have a John Deere GX345 w/54" convertible deck, the adjustment dial will not work. hydraulics work ... A: >>The Only Time the Cam Engages/Touches Anything (the Mid-Lift Shaft #10) is when the Deck is ... | |
| Briggs & Stratton Engine | 5/23/2010 |
| Q: I have a Briggs & Stratton 16.5 HP OHV 1/C Model #313707. Before mowing this year I did routine ... A: >>From your Description it Does Sound like a Broken Conecting Rod, However, there are Other Possible ... | |
| mower deck | 5/23/2010 |
| Q: i found a spring under the mower adjustment plate that was loose. i cant find where the other end of ... A: >>Thanks. >>The Spring Attaches to the Heigth Adjustment Lever and is Supposed to Hold the Lever ... | |
| height adjustment dial on a JD GX345 will not work | 5/22/2010 |
| Q: I have a John Deere GX345 w/54" convertible deck, the adjustment dial will not work. hydraulics work ... A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| Tecumseh TVXL220 will not start | 5/22/2010 |
| Q: This engine is on my Montgomery ward tractor lawn mower. I was cutting the lawn when the engine ... A: >>Does the Engine Turn Really, Really Easy as if the Spark Plug is Removed? >>Can you Turn the ... | |
| Lawn Mowers | 5/22/2010 |
| Q: at this point I'm at my wits END but I have a Craftsman 917.255371 I don't know the drive belt ... A: >>To View a Breakdown of this Unit Go to this Site Addy, ... | |
| kohler engine | 5/22/2010 |
| Q: kohler model cv20s runs only on choke have cleaned carb twice same results as soon as u try to give ... A: >>From your Description it Sounds like the Carburetor Solenoid is Bad and Requires Replacing. >>The ... | |
| briggs and stratton 3-1/2hp engine | 5/21/2010 |
| Q: Model 92908,type-1224-01, code-7202225 The mower has been giving excellent service for years but ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| followup to your responce on 5/14 | 5/21/2010 |
| Q: re: j.d. gx95 john thanks for your quick responce. i took out the fuel selenoid and tested it ... A: >>The Purpose for the Carburetor Solenoid is to Shut Off the Gas through the Main Jet of the ... | |
| backfiring kohler cv15s | 5/21/2010 |
| Q: We have a John Deere 255 garden tractor with a Kohler cv15s (15 h.p.) spec. # 41571 engine that ... A: >>You can View a Breakdown of the Engine at this Site Addy; http://www.kohlerplus.com/login.asp and ... | |
| Kawasaki FC420V mower | 5/20/2010 |
| Q: Mower runs ok on level ground. As soon as you try to go up any incline the unit will not move up the ... A: >>For Better Assistance, Send me the Model Numbers Off the Mower, Please. With these I can Locate ... | |
| riding mower engine probs | 5/20/2010 |
| Q: I have a 12/36 Duralast. Two questions: 1.) I rebuilt the carb, and when placing that little while ... A: >>1- The Float Needle Valve Seat (O-ring) should have been Installed with the Rounded Side Towards ... | |
| Peerless transaxle in 1999 Murray 46570X8B | 5/20/2010 |
| Q: Hey John, I saw that you had a similar question, but the guy never got back to you with his model ... A: >>You can View a Breakdown of this Mower At this Site Addy; ... | |
| JD RX-95 has 2 speeds FWD and REV. | 5/20/2010 |
| Q: I just bought a JD RX-95 and it's in great shape, aside from a speed issue. No matter what gear is ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| mtd chipper/shredder briggs and stratton 135212-0140-01 | 5/20/2010 |
| Q: I have an mtd chipper shredder with a Briggs and Stratton motor model 135212-0140-01. I bought this ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| Toro electric start - continued | 5/19/2010 |
| Q: I have a Toro model 20074, SN 270000325. The battery is good at 12.9 volts. I have followed the ... A: >>I am Guessing this is a Question and Answer from Another Expert here at All Experts. >>From your ... | |
| Honda Harmony | 5/19/2010 |
| Q: I have a walk behind Honda mower 6.5hp, 5 years old. It takes about 10 minutes to cut my lawn. Very ... A: >>Sorry for the Delay. Power went Out and All 3 of my Generators were in Use in the Field. >>Also, ... | |
| blade wont engage | 5/19/2010 |
| Q: John, I have a simplicity rider that worked fine last night and now wont engage blades. The blade ... A: >>From your Description it Sounds like the PTO Require Adjusting or Replacing. >>The Blades are ... | |
| john Deere la 140 | 5/19/2010 |
| Q: my john Deere la140 is only firing on one cylinder it is a 23 hp Briggs and stratton i have replaced ... A: >>You can View a Breakdown/IPL of the Engine at this Site Addy; ... | |
| New engine | 5/19/2010 |
| Q: John,Or....Mr.President :-) I am back again.I want to purchase a new engine.So,I have to use one of ... A: >>Welcome Back. I Hope all is Well with You and Yours. >>I have Several Online Companies that I use ... | |
| JD L110 | 5/18/2010 |
| Q: I am having problems with my L110 it is dumping way to much fuel in the carb & i have pulled the ... A: >>From your Description it Sounds like the Carburetor Float Needle Valve is Not Seating Correctly. ... | |
| Craftsman mini tiller | 5/18/2010 |
| Q: I have an older, maybe 6 years old, Craftsman mini tiller. It was operating fine until the tines ... A: >>From your Description and Depending on the Model, it can be a Shear Pin or a Bad Clutch Assy. ... | |
| noma mower | 5/18/2010 |
| Q: i have a noma lawn tractor model g4015000 serial# s001095337776 with a peerless transmission 6040 ... A: >>From your Description it Sounds like a the Pinion Gears are Worn or there is a Woodruff Key that ... | |
| Identify # 1 cylinder | 5/18/2010 |
| Q: 18HP b%26s intec opposed engine, 42A707. Sitting on the tractor, which cylinder is # 1? I have no ... A: >>Looking at the Engine from the Carburetor, #1 Cylinder is to the Right. >>You can View a ... | |
| Montgomery ward 5 hp tiller | 5/18/2010 |
| Q: I have a MW 5 hp tiller that is from 1976 and in very good shape. I feel I am not getting spark. I ... A: >>The Following is the Instruction File I Made for Removing the Flywheel and Replacing the Point Set ... | |
| Lawn Mower Won't Start | 5/18/2010 |
| Q: need some assistance with my mower. MTD Yard Machines OHV Power More (chinese engine). ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| 4 Cycle Craftsman Incredi Pull Tiller | 5/17/2010 |
| Q: I have a Craftsman 4 Cycle Incredi-pull Tiller/Edger Model # 316.292711 that has a broken pull rope. ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Charging System Briggs & Stratton | 5/17/2010 |
| Q: I have John Deere Riding lawnmower , and its doesn't stay charged , When i charge the battery it ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Kohler engine problem | 5/17/2010 |
| Q: Paul, I have a Sears rider with a Kohler CV490 motor. It's about 5 years old and has been great ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| John Deere L110 Lawn Mower Shearing Flywheel Keys | 5/17/2010 |
| Q: I have a 5 yr old John Deere L110 Lawn Mower. Recently while I was mowing thick grass the mower ... A: >>From your Description it Sounds like the Flywheel Nut/Starter Clutch Requires More Torque. >>The ... | |
| B&S 15 hp white smoke | 5/17/2010 |
| Q: I have a Briggs & Stratton 15hp in a riding mower (Model 28Q777 Type 0681-01) bought in 1997. It ... A: >>The Following is an Instruction File I Made for the Gas Contamination of the Crankcase Oil and/or ... | |
| starter cord hard to pull | 5/17/2010 |
| Q: I have a "General Power Products" 13 horse engine on a log splitter. It's a "Honda" knockoff, made ... A: >>Since this is an OHV Engine, then >>Set the Valve Clearances. >>The Valve Clearances with either ... | |
| john deere 21 inch push mower | 5/17/2010 |
| Q: I have a 21 inch john deere push mower that has a briggs motor on it, 3.5hp i think model:93508 ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| Kohler Engine Problem | 5/17/2010 |
| Q: John, thank you for your quick response. Sorry it took so long to get back to you. It is very hard ... A: >>Wow, it has been a while (4/22/10). >>According to my Files you haven't Read my Last E-mail (that ... | |
| Toro Lawnmower question | 5/16/2010 |
| Q: I have a Toro Personal Pace 6.0 H.P. self-propelled mower. It was just serviced, yet while mowing, ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Briggs & Stratton Possible Magneto Issue | 5/16/2010 |
| Q: and I was able to cut the whole front lawn ok. I stopped the mower, moved to the back yard - but the ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| 10 Horsepwer Tecumsah Engine | 5/16/2010 |
| Q: On the front of the motor is an on/off switch, I was wondering where I can find a replacement ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Tecumseh Engine | 5/16/2010 |
| Q: John, I have a Murray Model # 405005x99B. It has a Tecumseh engine OHV135-206908E. The mower was ... A: >>Remove the Blower Housing (metal engine cover) and Clean out Any Debris. >>Mice Love to make Nest ... | |
| Lean Kawasaki Carb | 5/16/2010 |
| Q: I have a Kawasaki FH451V engine in a Husqvarna Lawn Tractor. It has been running fine for many ... A: >>When you Cleaned the Carburetor, Did you Soak it or Clean it with Spray Cleaner? >>The Following ... | |
| craftman riding mower shifter stuck | 5/16/2010 |
| Q: This question is similiar to one a guy named garrett asked. The blades engage and everything else is ... A: >>From your Description it Sounds like the Shift Keys Inside the Transaxle are Worn and Require ... | |
| Honda Harmony | 5/16/2010 |
| Q: I have a walk behind Honda mower 6.5hp, 5 years old. It takes about 10 minutes to cut my lawn. Very ... A: >>From your Description it Sounds like the Valve may Require Setting, the Timing Belt has Stretched ... | |
| 8h9 kohler engine | 5/16/2010 |
| Q: its spec is 30593d model k181s is all set for lp. where do i get info? set up, connections,ect. A: >>I am Not Completely sure I Understand the Question. >>However, this is the Site Addy; ... | |
| JD 265 lawn mower | 5/15/2010 |
| Q: Last time mowing it started leaking a little oil onto deck. I tore into it today took valve cover ... A: >>The Following is an Instruction File I Made for the Gas Contamination of the Crankcase Oil and/or ... | |
| B & S carb | 5/15/2010 |
| Q: I have a 6.0 Briggs SN#2H302 2639 B1 010417EA, I can get it to start but not run. I have cleaned the ... A: >>Can you Check the Engine Model Numbers for me, Please. I am having Trouble Locating a 2H302 ... | |
| Engine Pumping Oil in Carb. | 5/15/2010 |
| Q: John: I have a LT 1000 Sears Mower with a 15.5 Briggs & Straton Engine. When I last mowed my yard ... A: >>From your Description it Sounds like the Crankcase Vent/Breather Requires Cleaning or the Valve ... | |
| Sabre 1438HS Lawn Tractor | 5/15/2010 |
| Q: I have a Sabre 1438HS lawn tractor that's about 8 years old with a 14.5 hp Briggs and Stratton ... A: >>The Following is a Basic Instruction File I made for this. Any Input is Appreciated. I Usually ... | |
| Kohler engine smokes | 5/15/2010 |
| Q: My sears craftsman LT1000 has been starting hard this year, and running rough. During starting ... A: >>From your Description it Sounds like a Blown Head Gasket and the Carburetor Float Needle Valve is ... | |
| Toro 56145 - 8-32 Mower Popping out of reverse | 5/14/2010 |
| Q: John, First let me say thanks for taking the time to answer questions for everyone on here! I have ... A: >>THINK SAFETY: Always Remove the Spark Plug Wire/s from the Spark Plug/s and Tie Away from the ... | |
| Lawn mower | 5/14/2010 |
| Q: I have a mower with a Briggs & Stratton 10.5 hp I/C engine Model 28B702, Type 1001-E1, Code 990203ZD ... A: >>Honestly, the Best Solution Anymore for this Problem is to Install a 1/4 Turn Cut Off Valve and ... | |
| Craftsman 21cc string trimmer | 5/14/2010 |
| Q: Have a craftsman 21cc weed whacker. My dilemna is that the fuel lines rotted and fell off there ... A: >>THINK SAFETY: Always Remove the Spark Plug Wire/s from the Spark Plug/s and Tie Away from the ... | |
| jd gx95 | 5/14/2010 |
| Q: your answers to wayne were helpful can you tell me how to test the fuel solenoid and the fuel pump ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| lawn chief tiller | 5/14/2010 |
| Q: i have a model #66A and i would like to get a pic of the belt set-up ?? A: >>You can Use the Site Addys at this Site Addy; http://www.yetmans.mb.ca/antiques.html to Search and ... | |
| John Deere RX95 | 5/13/2010 |
| Q: Can you point me at a belt path diagram for this mower? Thank you very much. Al A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| adj valves on 17hp brigs | 5/13/2010 |
| Q: i would like to no just how to adjust the valves on the motor? andhow can i tell when both valves ... A: >>THINK SAFETY: Always Remove the Spark Plug Wire/s from the Spark Plug/s and Tie Away from the ... | |
| troy bilt tiller | 5/13/2010 |
| Q: I just bought a tiller at auction model number on gas tank is H50 65283K SERIAL IS 1341D IS THERE ... A: >>Generally the identification tag is on a part of the unit that, even after years of use, rarely ... | |
| crankshaft seal | 5/13/2010 |
| Q: How do I change the crankshaft seal in my Tecumseh 13HP riding mower engine. The model # is OHV130 ... A: >>THINK SAFETY: Always Remove the Spark Plug Wire/s from the Spark Plug/s and Tie Away from the ... | |
| briggs 5hp magnum armature air gap | 5/13/2010 |
| Q: i'm reassembling a briggs 5hp magnum lawn mower engine. when i got it it was disassembled. i don't ... A: >>No Worries. >>***Anytime a Magnet that is Set to the Correct Distance from the Armature/Ign Coil ... | |
| Occassionally smokes (oil) on startup. | 5/13/2010 |
| Q: I have a twelve year old 17 horse Kawasaki, air cooled, single cylinder engine that on occasion will ... A: >>From your Answers to my Questions about the Oil use and Power Loss, I can Tell you the Smoke may ... | |
| John Deere 425 Valve adjustment | 5/13/2010 |
| Q: I would like to adjust the valves on my John Deere 425 AWS. I have a 20HP OHV engine. I understand ... A: >>The Intake Valves are Nearest the Flywheel End of the Engine. >>You can View a Breakdown/IPL of ... | |
| harmony 215 honda self PP mower | 5/13/2010 |
| Q: My self propelled..is starting to skip or it seems..to not fully engage in the self propelled ... A: >>Using a Breakdown of the Unit and Asking Questions of the All Experts People if Required, you ... | |
| Troy-bilt drive train. | 5/12/2010 |
| Q: I just replaced all the belts on a 2007 Troy-Bilt Pony because I was having trouble going up hill. ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| backfired, now wont start | 5/12/2010 |
| Q: I have a craftsman riding mower w/21hp v-twin b&s engine. while on a slight incline on my trailer, I ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| small engine | 5/12/2010 |
| Q: so i have a 15.5 hp Briggs on a craftsman rider. it turns hard and wont fire, until i remove the ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| John Deere 757 switch problem? | 5/12/2010 |
| Q: I have 2005 John Deere 757 mower. That has started to just stop running when in use. It can run fine ... A: >>Did you Check the Control Lever Interlock Switch. >>From your Description it Sounds like the ... | |
| Onan 16hp in a Case 446 | 5/12/2010 |
| Q: Onan B43M GA016 (intake #170-2968). Trying to find a new Valve cover set. Mine is dented and worn ... A: >>You can get More Information About Onan Engines from this Site Addy; ... | |
| Occassionally smokes (oil) on startup. | 5/12/2010 |
| Q: I have a twelve year old 17 horse Kawasaki, air cooled, single cylinder engine that on occasion will ... A: >>From your Description it Sounds like the Oil Rings may be Worn and Allowing Oil to Seep into the ... | |
| engine weak | 5/12/2010 |
| Q: i have a 16.5 hp twin cycle murray model#42a707 it will only idle with the air filter and cover on ... A: >>There may be a Few Changes in the Wiring, but if the Engine has the Same Length, Diameter and ... | |
| Ryobi 975R trimmer | 5/12/2010 |
| Q: Have a Ryobi 4 cycle trimmer. Read the FAQs but I'm still stumped. Runs only on full choke, as you ... A: >>You Missed something in the Carburetor. >>The Old Solution may Not have Cleaned the Carburetor. ... | |
| YardMachine Riding mower | 5/11/2010 |
| Q: I have a Yard Machine 600 series riding mower. Wouldn't crank. installed new batter, told I need new ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| How old is my mower? | 5/11/2010 |
| Q: I just purchased a Murray mower and am trying to find out how old it is. The model number is 30550B ... A: >>Murray is Now Handled by Oscar Wilson Engines and Parts. >>Their Contact Number is 800-873-6722. ... | |
| tecumseh | 5/11/2010 |
| Q: i have a oh 180 early to mid 80s model with no spark and the coil is 175 dollars what do you think ... A: >>Sorry for the Delay. I was Tied up with Drs Appointments All Day and was Not ABle to Answer ... | |
| TORO model 20067 mower self/propelled | 5/11/2010 |
| Q: When using self propel, mower makes very loud noise; not using s/p sounds normal. This machine has ... A: >>Sorry for the Delay. I was Tied up with Drs Appointments All Day and was Not Able to Answer ... | |
| Intek running issues after hot only | 5/11/2010 |
| Q: Just wondering if you figured the issue out with that Intek you were having issues with after 45min ... A: >>If you can Keep the Engine Running by using the Choke, then >>Either the Carburetor Fuel Pump is ... | |
| drive belt | 5/11/2010 |
| Q: how do you change the belt on a self propelled 160cc honda engine(craftsman)? i removed the blade ... A: >>Sorry for the Delay. I was Tied up with Drs Appointments All Day and was Not ABle to Answer ... | |
| DYT 4000 | 5/10/2010 |
| Q: I have a Craftsman DYT 4000 and my son-in-law was mowing for me a few months ago and I found out ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Blade-matic blade clutch | 5/10/2010 |
| Q: I have been reading your posts on this forum and am knocked out by your knowledge. I have an obscure ... A: >>"Comet" was Acquired by "CPC" in an Auction on Dec 17, 2009. >>You can Contact them for ... | |
| B&S Lawn Mower | 5/10/2010 |
| Q: I have a B&S 123K02 lawn mower. I ma re-assembling and can't figure out how to connect the throtle ... A: >>I Do Not have Pictures, but this might Help. **The Throttle Cable Attaches to the Throttle Control ... | |
| Intek running issues after hot only | 5/10/2010 |
| Q: Just wondering if you figured the issue out with that Intek you were having issues with after 45min ... A: >>I Do Not Remember Receiving an Update about the Engine in Question. >>If this is a Twin Cylinder ... | |
| Hot smokin muffler | 5/10/2010 |
| Q: Hey smarty pants!!!!!!!!!!!! You did it sir!!!No more gas out the air filter.That is solved by me ... A: >>Have you Checked Under the Blower Housing and made Sure the Area is Clear of Debris? >>Mice like ... | |
| transaxle | 5/9/2010 |
| Q: Will transaxle out of John Deere STX38 hydro fit John Deere Sabre 1542 hydro? A: >>No Sir they will Not Interchange. >>There is a Hydro-Gear K50 or K55 Transaxle in the Sabre and ... | |
| Craftsman 32cc Leaf Blower/Mulcher/Vac | 5/9/2010 |
| Q: I just found a craftsman 32cc leaf blower/mulch/vac 170mhp. I tried starting it and it runs for a ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| Ryobi SS30 grass trimmer | 5/9/2010 |
| Q: I am trying to disassemble my trimmer and found you response on the web. You said "Remove the ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| Kohler CV20s on craftsman mower | 5/9/2010 |
| Q: I have replaced the spark plugs,fuel filter, changed the oil changed out old gas and new air filter ... A: >>From your Description it Sounds like the Carburetor Solenoid (if Applicable) is Bad or the ... | |
| Gas in air filter | 5/9/2010 |
| Q: I have tried everything john to no avail.New carb....It is not float,seat,valve.Breather clean.Now ... A: >>The ONLY Other Possible cause for Excessive Gas Spray from the Carburetor Intake is the Intake ... | |
| Honda mower won't stay running | 5/8/2010 |
| Q: I have a Honda Harmony 215 push mower, engine serial number GJAB-6530404. It sat for about a year ... A: >>From your Description it Sounds like a Bad Carburetor Shut Off Solenoid or the Carburetor Requires ... | |
| Old B & S Ignition Conversion | 5/8/2010 |
| Q: I have an old International Harvester Cub Cadet 75 rider mower with a Briggs and Stratton engine ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| briggs & stratton | 5/8/2010 |
| Q: I think it has two black wires coming out the side not sure were they go if you could help i would ... A: >>Thanks for the Model Numbers. They are a Great Help. Go to this Site Addy; ... | |
| oil leak / white smoke | 5/8/2010 |
| Q: i read some of your replys and you may have already answered this question but here we go .i have a ... A: >>From your Description it Sounds like the Head Gasket Blew between the Cylinder and the Push Tube ... | |
| Crankcase vent | 5/8/2010 |
| Q: Tecumseh OH195XA-71228 Hi John. What is the easiest way to get to the crankcase vent on my engine? I ... A: >>From your Description it Sounds like the Carburetor Needle Valve is Not Seating Correctly and is ... | |
| briggs & stratton | 5/7/2010 |
| Q: I think it has two black wires coming out the side not sure were they go if you could help i would ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| 7hp kohler intake valve | 5/7/2010 |
| Q: I have an old kohler 7hp horizontal shaft engine from a Troy-bolt tiller. I do not know the year or ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| Idles high then low | 5/7/2010 |
| Q: I am back again with the tecumseh OH195XA-71228 Revs high,then low,then dies.I cleaned carb ... A: >>Thanks, but Don't get me Started on Running the Country. LOL. >>I'm Glad the Idling Problem has ... | |
| john deere blades don't engage | 5/7/2010 |
| Q: I re-grounded the Pto ground wire and it still won't engage. Ohms on clutch registered around 2. ... A: >>From your Description it Sounds like the Coil has Shorted and Requires Replacing. 2 Ohms is Lower ... | |
| honda lawn mower drive clutch cable | 5/6/2010 |
| Q: Honda Harmony HRB 215. While mowing the lawn I let off the drive clutch to make turn, when I went to ... A: >>LOL. No Worries. This is Usually a Simple Repair. >>You can View a Breakdown/IPL at this Site ... | |
| Idles high then low | 5/6/2010 |
| Q: I am back again with the tecumseh OH195XA-71228 Revs high,then low,then dies.I cleaned carb ... A: >>Welcome Back. >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| Kohler Command V twin running rough | 5/6/2010 |
| Q: I recently bought an '99 Allmand Brothers backhoe with a Kohler Command V twin, 25 hp. It ran for ... A: >>First, Change the Spark Plug. >>Second, Check the Coils. >>Remove the Spark Plugs and Wrap the ... | |
| B&S fuel problem | 5/6/2010 |
| Q: I have a B&S engine 3402437 0770 01 on a Bolens mower. It will not run unless the choke is ... A: >>Thanks for Clearing up the Model Numbers for me. >>Check the Fuel Shut Off Solenoid. >>The ... | |
| JOHN DEERE 285 CARBURATOR & GOVENOR LINKAGE | 5/6/2010 |
| Q: ..my dad is 70 and not computer savvy, so I am asking this for him. He has a JD 285 with a 18HP ... A: >>The Following is a Basic Instruction File for Removing Carburetors on Small Engines. Any Input is ... | |
| Echo SRM 2400 | 5/5/2010 |
| Q: I have an Echo 2400 that will only start when I remove the spark plug and pour gas directly into the ... A: >>Did you Soak the Carburetor or Use Spray Carburetor Cleaner to Clean the Carburetor when you ... | |
| B&S fuel problem | 5/5/2010 |
| Q: I have a B&S engine 3402437 0770 01 on a Bolens mower. It will not run unless the choke is ... A: >>I Think this is a 302437-0770-01 Model Engine. >>Always Remove the Spark Plug Wire/s from the ... | |
| mower quits after 1-2 hours of mowing | 5/5/2010 |
| Q: twin cyl l head. b & S 18 hp I think. Runs great for 1-2 hours then quits. acts like dead battery, ... A: >>Have you Checked the Gas Cap and made Sure it is Venting Correctly? >>Check the Valve Clearances. ... | |
| craftsman seat safety switch | 5/5/2010 |
| Q: John, My lawn tractor (Craftsman circa '04) with Briggs & Stratton 18.5 HP engine starts and runs ... A: >>From your Description it Does Sound like the Seat Safety Switch is Bad or has a Bad Connection. ... | |
| Torque specs | 5/5/2010 |
| Q: John, In response to your question about the counterweight screw (that is what I call it, I don't ... A: >>If the Crankshaft Pulley Bolt is NOT a Grade 8 Bolt, then Yes Please Replace it with a Grade 8 ... | |
| Cleaning mtd carberator | 5/4/2010 |
| Q: I spoke to someone and they said my carburetor is probably blocked and needs to be cleaned. Could ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| weed trimmer ryobi 720r | 5/4/2010 |
| Q: my gas runs into carburetor to fast and chokes the engine and it dyes put new CB. kit on. before ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Murray | 5/4/2010 |
| Q: I bought a used Murray Power Trac 20 HP Twin 52in. I cant find the model number anywhere. I need a ... A: >>Riding mower tags are located on the underside of the seat. For walk behind mowers this tag is ... | |
| scag mower | 5/4/2010 |
| Q: I have a scag turf runner model str-22ch serial# 21760306 with a Kohler Command 22hp model ch22s ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| tecumseh problem | 5/4/2010 |
| Q: tecunseh 3 1/2 hp on lawnchief mower.. mower sat in garage unsed several years, run dry of ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| Ryobi 975R trimmer | 5/4/2010 |
| Q: Have a Ryobi 4 cycle trimmer. Read the FAQs but I'm still stumped. Runs only on full choke, as you ... A: >>I Hopefully will be here Until we Correct this Problem of we Both Throw a Fit and Junk it. LOL. ... | |
| B/S 14 HP Engine Will Not Start | 5/3/2010 |
| Q: I have Craftman Lawnmower with a 14HP B/S engine. When the weather is cool outside, 50 - 70F, it ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| tecumseh ohv17 in weedeater rider | 5/3/2010 |
| Q: I have a weedeater model number wet1742, engine model ohv17, i have replaced the spark plug, drained ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| lawn tractor mower v-belt | 5/3/2010 |
| Q: I have a 1998 Toro 267H, model #72085 with a Toro 48" wide mower, model #78265. I could get a new ... A: >>Have you Tried your Local Auto Parts Retailer? >>For Most of my Belts I Use the Industrial Belts ... | |
| engine runs then dies | 5/3/2010 |
| Q: I have a John Deere 314 with a Kohler K321AQS engine spec no. 60343 . It starts right up and runs ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| Craftsman mower stalls when putting in gear | 5/3/2010 |
| Q: John, I have an old craftsman LT-10 36 inch deck 10hp from the 80's. Running fine last season. I ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| Wiring | 5/3/2010 |
| Q: I have a PowerPro 18 Horse Power 42" Lawn Tractor Briggs %26 Stratton engine. It would not start, ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| Ryobi 975R trimmer | 5/3/2010 |
| Q: Have a Ryobi 4 cycle trimmer. Read the FAQs but I'm still stumped. Runs only on full choke, as you ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| murray riding lawn mower | 5/2/2010 |
| Q: My lawn mower will hit, but won't keep running. It's full of gas, the battery is fine, and I've ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Ariens lawnmower not moving | 5/2/2010 |
| Q: Mylawnmower recently began to have a hard time moving under load. will go uphill at a very slow ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| Auger doesn't turn -- is my gearbox broken? | 5/2/2010 |
| Q: 887990 9 HP/29 " Dual Stage Snowthrower. During our last big snowstorm, I lent my machine to my ... A: >>No Worries. I am Glad to Help all I can. >>Did you Sandpaper (440 Grit or Emory Cloth) the Shaft ... | |
| MTD Riding Mower Steering Problems | 5/2/2010 |
| Q: I have a MTD 12.5 HP and I'm having a problem with the steering drag link. I replaced the Drag Link ... A: >>Always Remove the Spark Plug Wire/s before Working on Any Small Engine unless the Plug/s must be ... | |
| Yard Machine Push mower | 5/2/2010 |
| Q: I have recently started the mowing season, I have indeed mowed a couple of times this year thus far, ... A: >>Always Remove the Spark Plug Wire/s from the Spark Plug/s before Working on Any Small Engine ... | |
| Torque specs | 5/2/2010 |
| Q: I have a Briggs and Stratton model 287707, type 1272-E1 engine mounted on a Murray 425003x8 lawn ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| needle valve and seat | 5/1/2010 |
| Q: i dont no what one to get can you help me model 21a807 type 0241e1 code 031201za A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Rope hard to pull | 5/1/2010 |
| Q: John, I have a Craftsman Eager-1 Model 917.377380 with a tecumseh 143.006700 engine. After ... A: >>On a Flat Head/L-Head Engine when the Clearances become Larger/Wider than Suggested, then you need ... | |
| Honda GCV160 5.5hp engine | 5/1/2010 |
| Q: 1. Is there any way to adjust the automatic choke or its travel? 2. I hear that there are two ... A: >>Since the Carburetor Adjusting Screws were Not Removed for Soaking, the Carburetor will have to be ... | |
| JD F525 choke problem | 5/1/2010 |
| Q: I have a John Deere F525 that will not start with the choke. A little bit of gas in the air intake ... A: >>The JD F525 is All the Information I Require for this Unit to Locate the Correct Breakdown/IPL. ... | |
| Rope hard to pull | 5/1/2010 |
| Q: John, I have a Craftsman Eager-1 Model 917.377380 with a tecumseh 143.006700 engine. After ... A: >>I was Brought Up to Believe that "The Only Stupid Question was the Unasked Question". >>No One can ... | |
| LAWNBOY MOWER | 5/1/2010 |
| Q: JOHN, I HAVE AN OLD LAWNBOY MOWER MODEL#R7266 WHICH HAS BEEN IN THE FAMILY SINCE NEW AND HAS ... A: >>Other than the Seal between the Jug and Block Leaking and the Rings, there is Nothing that would ... | |
| Toro GTS 6.75 hp won't stop running | 4/30/2010 |
| Q: I have Toro GTS walk behind. It work and run OK. the problem is it won't cut off. I disconnect spark ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| kohler cv460s backfiring in carb | 4/30/2010 |
| Q: i have a john deere lt160 with a kohler cv460s-26516 ser#3306510013 family #3khxs.4902gb this unit ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Agway lawn tractor | 4/30/2010 |
| Q: I have a 12hp Agway Riding Mower. I was giving my 5 year old daughter around the yard with the ... A: >>From your Description it Sounds like an Idler Pulley has Frozen and Burnt the Ground Drive Belt. ... | |
| LAWNBOY MOWER | 4/30/2010 |
| Q: JOHN, I HAVE AN OLD LAWNBOY MOWER MODEL#R7266 WHICH HAS BEEN IN THE FAMILY SINCE NEW AND HAS ... A: >>From your Description it Sounds like a Compression Problem. >>What is the Compression on this ... | |
| craftsman 13 HP 30" riding mower | 4/30/2010 |
| Q: i have a craftsman 13 HP tecunseh 30" cut. model number 143.961300. a while back while mowing ... A: >>From your Description it Sounds like the Valve Clearances Require Setting. >>The Following is a ... | |
| Rope hard to pull | 4/30/2010 |
| Q: John, I have a Craftsman Eager-1 Model 917.377380 with a tecumseh 143.006700 engine. After ... A: >>This is a Tecumseh LEV120-361501A Engine. >>Which Direction did you have the Spark Plug Pointed ... | |
| Briggs 311777 0143E1 | 4/30/2010 |
| Q: John, could you help me with the bolt torque pattern for the crankcase on this engine. I found out ... A: >>The Torque Pattern is Simple. >>With the Sump/Oil Pan Facing Up, Snug All the Bolts Starting with ... | |
| Briggs&Stratton engine smoking | 4/29/2010 |
| Q: I have a Briggs 31c707-230-e1 17.5hp engine, I have adjusted the valves (as it would not start ... A: >>Did you Miss a Number when you Looked at the Model Numbers? 31C707-?230-E1. >>From your ... | |
| Kohler Governor | 4/29/2010 |
| Q: What is the easiest way to get at the internal governor on a Kohler cv493t engine? I am hoping that ... A: >>The Following is a Basic Instruction File for Examining the Inside of a Small Engine and will ... | |
| Power sport 6.0 Tecumseh linkage | 4/29/2010 |
| Q: John, I am back again on the linkage for Tecumseh OH195XA 71228J Emissions carburetor...choke style. ... A: >>You can Never "Bug" me with Problems concerning Small Engines and ATV's. >>I had to Look up you ... | |
| briggs and stratten | 4/29/2010 |
| Q: its me again with the briggs and stratten model 31c7070154E1. I'm the one who replaced the ... A: >>I Hope All is Well With You and Yours. >>The Choke Link (#216)is a Solid Link that is Curved on 1 ... | |
| pressure washer | 4/28/2010 |
| Q: Troy-Bilt model 20240 engine Briggs %26 Stratton 125K02-0137-E1-05081956. I found your 2008 ... A: >>Usually if the Pump is Frozen, the Engine will Not Turn. >>Did you Soak the Carburetor in Cleaner? ... | |
| Scotts S1642 - Blows white smoke then stops | 4/28/2010 |
| Q: I have a Scotts S1642 riding mower with a Kohler CV16S (Spec #43526) engine. After running for 5-10 ... A: >>Thanks for the Blessings. >>The Fluid Running Down the Exhaust Pipe is Usually Oil from a Leak at ... | |
| peerless trans. 205-023B | 4/28/2010 |
| Q: John, I have a 205-023B vst that has very little speed or power. It is in a yard king machine that ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| gx95 riding john deere lawn mower (no start) | 4/27/2010 |
| Q: My gx95 lawn mower wont start.When i test for spark I'm removing the plug,reinstalling the wire to ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| L130 Stalled | 4/27/2010 |
| Q: I have a similar problem where my L130 stalled out of nowhere almost like it was out of gas. I ... A: >>I am Including 2 Files. >>The First is to Ensure the Coil is Not the Cause and the Second is for ... | |
| Tecumseh linkage | 4/27/2010 |
| Q: I have a new tecumseh 6 h.p.spring loaded go kart engine.I cant even get help at lawnmower ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| blade removal | 4/27/2010 |
| Q: I have a John Deere lawn mower. Walk-behind type JS60. Which way does the bolt turn to remove the ... A: >>I do Apologize, I should have Written that it Doesn't Matter if it is a Nut or a Bolt, they still ... | |
| Linkage | 4/27/2010 |
| Q: I have a new tecumseh 6 h.p.spring loaded go kart engine.I cant even get help at lawnmower ... A: >>I Called Tecumseh and Spoke with a Service Technician and they Sent me an E-mail Attachment of the ... | |
| Scotts S1642 - Blows white smoke then stops | 4/27/2010 |
| Q: I have a Scotts S1642 riding mower with a Kohler CV16S (Spec #43526) engine. After running for 5-10 ... A: : >>Is the Crankcase Over Filled? >>Does the Crankcase Oil have a Gas Smell to it? >>Does the ... | |
| Kawasaki charging system | 4/27/2010 |
| Q: I have a Ferris mower with a Kawasaki FH660V motor. I will not charge the battery. Can there be ... A: >>You can View a Breakdown of this Engine at this Site Addy; http://www.kawpowr.com/ and Select ... | |
| 1984 Suzuki DR250 CDI and Coil | 4/26/2010 |
| Q: I need a CDI box and coil for my 1984 Suzuki DR250. I was wondering where I could find them parts ... A: >>Usually the CDI is the cause for No Fire to the Plug on this Unit. >>It is Rare for the Coil to ... | |
| deere l110 won't start | 4/26/2010 |
| Q: I have a John Deere l110 riding mower with a 17.5hp Kohler engine. When I tried to start it up this ... A: >>Thanks for giving me the "Whole Story". >>From your Description it Sounds like the Starter Drive ... | |
| engine weak | 4/26/2010 |
| Q: i have a 16.5 hp twin cycle murray model#42a707 it will only idle with the air filter and cover on ... A: >>Ouch!! That is a Bad Thing. >>It Sounds like you had the Wrong Spark Plug (too hot). >>I Usually ... | |
| briggs and stratten engine | 4/26/2010 |
| Q: 5hp model 31c7070154e1 that backfires after i replaced the alternator on the riding mower. When i ... A: >>Thanks for the Kind Words. You and Everyone that I Assist is More than Welcome to "Pick my Brain" ... | |
| deere l110 won't start | 4/25/2010 |
| Q: I have a John Deere l110 riding mower with a 17.5hp Kohler engine. When I tried to start it up this ... A: >>The Following is an Instruction File I Made for Checking/Testing the Starter and Solenoid. ... | |
| Echo weed Trimmer Carb problem | 4/25/2010 |
| Q: I have a Model SRM2100 ( about 7 years old). Was running poorly (had done little maintenance. Carb ... A: >>You can View a Breakdown/IPL of this Unit at this Site Addy, ... | |
| blade romoval | 4/25/2010 |
| Q: I have a John Deere lawn mower. Walk-behind type JS60. Which way does the bolt turn to remove the ... A: >>The Rule for Loosening Most Blade Nuts is; they Loosen by "Turning them the Same Direction that ... | |
| JD L130 steer reassmbly | 4/25/2010 |
| Q: John, I have a JD L130 lawn tractor I bought at a Home Depot in 2004. The front wheels had a bad ... A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| briggs and stratten engine won't start | 4/25/2010 |
| Q: i replaced alternator now it wont start only backfires-its a pony troybuilt briggs& straton 17.5 hp ... A: >>Did you Tighten the Flywheel Correctly. >>The Torque for the Flywheel Nut is 100ft Pounds. >>If ... | |
| weed eater pull rope | 4/24/2010 |
| Q: when i try to start my weed eater there is no tension on the pull rope. It still recoils, but there ... A: >>From your Description it Sounds like the Recoil Starter Dawgs have Frozen and Require Cleaning and ... | |
| torque specs | 4/24/2010 |
| Q: sears m#917.2736403 18.5hp,what are the head bolt torque specs? Thank You Mike ANSWER: Hello ... A: >>Thanks for the Kind and Good Words. I Hope to be Better in a Few Weeks. >>The Oil Dripping from ... | |
| honda 5.5 hp idling problem | 4/24/2010 |
| Q: I read the questions and answers on a guy named bob that had tried cleaning and cleaning the ... A: >>This is Why I like to get Comments from the Questioners. >>Usually the Comments will Provide an ... | |
| throttle linkage(s) | 4/24/2010 |
| Q: Have a Sears mower Craftsman Eager 1 model 917 386 140 with engine 5 H. P., model 143.965002. Yes ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| masport mower briggs and stratton 4stroke | 4/23/2010 |
| Q: i have a 90s model masport with a 635 craftsman briggs and stratton 4 stroke engine that wont start A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| CRAFTSMAN TILLER 6hp OVERHEAD VALVE SPECS | 4/23/2010 |
| Q: I NEED TO KNOW THE VALVE SPECS FOR A CRAFTSMAN TILLER MODEL NUMBER 917.293650/ENGINE TECUMSEH ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| John Deere LX176, 14 hp Kawasaki | 4/23/2010 |
| Q: I see where you helped a gentleman with a 14hp Kawasaki several years ago on the bolt torque for the ... A: >>It is Better to Tighten these Bolts in a Crisscross Pattern. This way the 2 Parts are Pulled ... | |
| string trimmer pushing fuel out | 4/23/2010 |
| Q: My old McCulloch string trimmer /32cc (CT M 32 EM) engine will blow the grommet and fuel lines out ... A: >>Are you Sure you have the Grommets Seated Correctly in the Tank? >>I have Never had this Problem ... | |
| Electric Hedge Trimmer | 4/23/2010 |
| Q: I have a Black and Decker HS2400 Hedge Hog hedge trimmer. I accidently tried to trim a metal fence ... A: >>From your Description it Sounds like the Gears are Jammed or Damaged. >>With the Unit Unplugged, ... | |
| Tecumseh compression release | 4/23/2010 |
| Q: I have a 13.5 hp Tecumseh engine, Model OV358EA,Type 206940G, 07351CB0099. The starter will not turn ... A: >>The Problem you Described is Usually caused by the Valve Clearances being Off Slightly causing the ... | |
| 21 hp Briggs and Statton twin cylender | 4/22/2010 |
| Q: My 21 hp briggs is hard to turn over. If you try to much the possitive cable gets hot at the ... A: >>This Appears to be a Flat Head/L-Head Engine. the Second Set of Instructions I Sent you is on How ... | |
| model #461707 Briggs | 4/22/2010 |
| Q: When I start the mower it starts but then it revs up and slows down and keeps repeating this like ... A: >>From your Description it Sound like the Carburetor Requires Soaking and Cleaning or the Gas Shut ... | |
| falters, won't start again | 4/22/2010 |
| Q: Mower: Craftsman LTX 1000.Engine: B/S Intec Platinum 20 HP, V twin. YBSXS-7242VF-27844. Cold, ... A: >>This can be caused by Several things. >>The Following is a Basic Instruction File I made for this. ... | |
| Kohler Engine Problem | 4/22/2010 |
| Q: I just bought a 1985 Wheel horse 312-A. It starts fine, idles and runs at full throttle fine. I ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| Stihl FS55R stalls when the throttle is released | 4/21/2010 |
| Q: Background: I have a two and a half year old Stihl FS55R string trimmer that, because it wouldn't ... A: >>lol. No Worries. >>The Jug Bolts are the 4 Bolts that Attach the Engine End Plate to the Engine ... | |
| Turf Till parts | 4/21/2010 |
| Q: I have a Turf Till cultivator and am having a hard time finding two replacement cables. They have a ... A: >>Other than Supplying you with a Site that you can use to Locate the Parts, my Time at the Present ... | |
| Craftsman riding mower wont start | 4/21/2010 |
| Q: 5 twin cylinder riding mower that wont start. The first time i tried to start it this year it ... A: >>From your Description it Sounds like a Safety Switch has a become Loose, the Mounting Bracket is ... | |
| 21 hp Briggs and Statton twin cylender | 4/21/2010 |
| Q: My 21 hp briggs is hard to turn over. If you try to much the possitive cable gets hot at the ... A: >>You have the L-Head or Also Called the Flat Head Engine. >>Send me the Model and Type or Spec ... | |
| john deere 14hp kaw will not start | 4/21/2010 |
| Q: I have a JD LX 176 with 14hp kaw engine - FC420V-AS10 engine. Had a new coil last fall and been ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| engine weak | 4/21/2010 |
| Q: i have a 16.5 hp twin cycle murray model#42a707 it will only idle with the air filter and cover on ... A: >>If by "Gas is everywhere", you mean that Gas is Leaking from the Carburetor, then the Carburetor ... | |
| 21 hp Briggs and Statton twin cylender | 4/20/2010 |
| Q: My 21 hp briggs is hard to turn over. If you try to much the possitive cable gets hot at the ... A: >>The Starter can be Binding/Dragging Under a Load and this would Explain why the Starter Turn the ... | |
| john deere stx38 not starting | 4/20/2010 |
| Q: I have a john deere stx38 model# CV12.5S, Spec# 1270, Ser# 240110538. It started to not get spark ... A: >>Usually the Igniter is the Cause for No Fire under the Conditions you Listed. >>However, lately ... | |
| Bolens 5.5 hp push mower won't start | 4/20/2010 |
| Q: I have a push mower that is 4 years old. B&S engine (10T7020498b1 07021955)(should be the model # ... A: >>If the Plug being Fouled by Gas was Not a Cause for this Problem, then >>Soak and Clean the ... | |
| Scag STT61A-27KA runs for about 15 minutes then stops | 4/20/2010 |
| Q: For about three years now this mower would run for about 30 minutes or so then it would act like it ... A: >>You can View a Breakdown/IPL of the Engine at this Site ... | |
| B&S not charging | 4/20/2010 |
| Q: I have a Yard Machine with a B&S 14.5 Model # 287707 TYPE 1224-E1 CODE 990108ZE It is not ... A: >>For Testing the Electrical (Charging) System on Mowers you can Use this Site Addy; ... | |
| Southern States Tiller SOR550 | 4/19/2010 |
| Q: I have enjoyed reading many of your answers. I have a specific question related to a rear tine ... A: >>Thanks for the Comments and for using All Experts. The Comments and Ratings are all we have for ... | |
| drive belt replacement | 4/19/2010 |
| Q: How do you replace the drive belt on LawnBoy model 10323? It does not appear that you can lift the ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| lack of power - 5 hp crafsman push mower | 4/19/2010 |
| Q: John, You have helped me in the past, so I thought I would turn to you again with a question. I have ... A: >>Thanks for coming back. I am Glad I was Able to Assist you Earlier. >>The Breakdown of this Mower ... | |
| Power Washer Engine | 4/19/2010 |
| Q: I have a Briggs and Stratton Quantum engine 12H812-2324-01-03082657 on a 6 horse power Excell power ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| CRAFTSMAN W/B&S | 4/19/2010 |
| Q: MY SISTER HAS A CRAFTSMAN 44",4 CYCLE, 2 CYLINDER RIDER. THE BATTERY WILL NOT STAY CHARGED. NEW ... A: Brown: >>From your Description it Sounds like the Stator/Charging Coils or the Voltage Regulator ... | |
| Replacement of Starter Group (490421) for Craftsman Lawn Tractor | 4/18/2010 |
| Q: I have a Craftsman Model 917.254860 lawn tractor. I need to replace the Starter Drive Group (490421) ... A: >>Some of the Starters Drives had a Spring/Roll Pin that you had to Drive Out and then Remove the ... | |
| STX38 powertrain | 4/18/2010 |
| Q: in a previous post i read that a tooth off the input bevel gear made the sympton of it in gear but ... A: >>Sorry for the Delay. The Weekend has Not been Kind to me and I am Behind in Answering Questions. ... | |
| Kawasaki FC420V-AS10 from JD LX172 | 4/18/2010 |
| Q: I just had a new head gasket put on this motor due to a bad oil leak. The engine still leaks oil. ... A: >>The Only other Possible Place the Leak could be from is the Upper Crankshaft Seal. >>With the ... | |
| john deere 285 runs poorly and about 1 hour | 4/18/2010 |
| Q: john- i have a john deere 285 liquid cooled lawn tractor, and it runs great for about 1 hour then it ... A: >>Check the Gas Tank Cap. >>The Following is a Basic Instruction File I made for this. Any Input is ... | |
| YS 4500 Craftsman Lawnmower 21 HP Briggs & Stratton | 4/18/2010 |
| Q: My lawnmower goes very slowly in forward and reverse position. It moves faster in reverse but still ... A: >>Sorry for the Delay. It's been a Bad Day for me and I'm getting a Late Start on my Questions. ... | |
| carburator | 4/17/2010 |
| Q: I have a murray 42" with a 229 carb on it. How do I tune the carb idling to rich and sometimes ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| JD 445 starting problems | 4/17/2010 |
| Q: I have a John Deere 445 that was running fine all winter long. It is I believe a 1995 with 596 ... A: >>Wow, that is Really Unusual and Rare. >>Thanks for the Feedback. >>I will add this as a Check to ... | |
| used the wrong oil | 4/17/2010 |
| Q: I put 2 cycle oil in my Kohler 4 cycle engine by mistake. Will this hurt the engine? A: >>If you Added this Oil to the Crankcase Oil, then >>Change the Oil ASAP. It will cause Internal ... | |
| Craftsman Garden Tractor No. 917.258863. 18.5 hp Kohler Engine | 4/17/2010 |
| Q: Looking for troubleshooting information or possible causes to this: The tractor starts then blows ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| 12.5 tecumseh starts then dies | 4/17/2010 |
| Q: 12.5 tecumseh model ohv125 will start if you pour gas in the carb then die in a few seconds,put a ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| engine swap | 4/17/2010 |
| Q: I have an mtd logsplitter m# 24AF501D700, the 6hp techumseh engine model 195ea is no good. I have ... A: >>You can Swap these Engines with Little Worries about RPM's. The Max RPM's are the so Close to ... | |
| Honda Harmony starter | 4/17/2010 |
| Q: I've gone through the electrical system and my starter is toast. I need to remove it but can't any ... A: >>Did you Look for the Starter Mounting Bolts being Vertical? >>Some Starters are Installed using ... | |
| jd 240 | 4/16/2010 |
| Q: i am working on a jd 240 garden tractor. the owner hooked up a battery charger backward, now it will ... A: >>Have you Checked the Stator/Charging Coils/Alternator? >>Hooking up the Battery Charger Backwards ... | |
| mower clicks but doesn't turn over | 4/16/2010 |
| Q: Mower ran fine. Put new tires, new spark plug, battery. Mower just clicks doesn't turn over. ... A: >>Try Checking the Starter. >>The Following is an Instruction File I Made for Checking/Testing the ... | |
| MTD Yard Machine 760/770 series | 4/16/2010 |
| Q: How do you install the rear drive belt? Thanks. A: >>For Better Assistance, Send me the Model Numbers Off the Mower, Please. With these I can Locate ... | |
| Craftsman Garden Tractor No. 917.258863. 18.5 hp Kohler Engine | 4/16/2010 |
| Q: Looking for troubleshooting information or possible causes to this: The tractor starts then blows ... A: >>Have you Checked the Stator/Charging Coils/Alternator for Overcharging? >>You can View a ... | |
| LT155 Drive belt | 4/15/2010 |
| Q: Do you know if the drive belt need to be routed above or below the guide (part# 4 M147132 GUIDE) in ... A: >>The Belt Goes Below the Guard. >>The Belt should Ride Between the Raised Section of this Guard. ... | |
| timing | 4/15/2010 |
| Q: i replaced connecting rod on a briggs and stratton model no. 124t02-0854-e1 and it wont start, i ... A: >>There is a Mark (- or a .) on the Crankshaft Gear Tooth and a Dot(.) between the Teeth on the Cam ... | |
| John Deere L100 Tractor: Need assembly help for spring which connects governor arm to throttle linkage | 4/15/2010 |
| Q: I need to figure out how to assemble the spring which connects the governor arm to the throttle ... A: **The Throttle Cable Attaches to the Throttle Control Bracket. The Cable Moves a Slide that Moves a ... | |
| Homelite saw won't stay running | 4/15/2010 |
| Q: My Homelite little red xl won't stay running for more than a minute or so. It runs smoother with the ... A: >>From your Description it Sounds like the Exhaust Port is Restricted and Requires Cleaning or the ... | |
| Stihl FS55R stalls when the throttle is released | 4/15/2010 |
| Q: Background: I have a two and a half year old Stihl FS55R string trimmer that, because it wouldn't ... A: >>Remove the Spark Plug and Check for Fouling. If the Plug Looks Clean and Not Fouled, then >>You ... | |
| Engine Damage | 4/14/2010 |
| Q: A 2004 John Deer push mower model JS63C is in my shop for repair. The blade was spinning freely on a ... A: >>Did you Check the Blade Adapter for Wear Inside the Key Way? >>I have seen this Occur a Few Times. ... | |
| Stihl FS55R stalls when the throttle is released | 4/14/2010 |
| Q: Background: I have a two and a half year old Stihl FS55R string trimmer that, because it wouldn't ... A: >>The Following is a Basic Instruction File for Doing a Diagnostic on the Engine for this Problem. ... | |
| torque specs | 4/14/2010 |
| Q: sears m#917.2736403 18.5hp,what are the head bolt torque specs? Thank You Mike ANSWER: Hello ... A: >>Did you Clean out the Crankcase Breather/Vent? >>If the Engine Over Revved, then the Compression ... | |
| Craftsman lawn tractor ignition switch | 4/14/2010 |
| Q: My son jammed a screwdriver into the ignition switch of my craftsman lawn tractor, model 917.288250, ... A: >>There should be a Nut Around the Key Hole of the Ign Switch that Holds the Switch and there May be ... | |
| Honda Engine | 4/14/2010 |
| Q: I have a Husqvarna Model 500CRT tiller that has a GC160 Honda engine (GCAHA-1872012-QHA2)on it. ... A: >>Replace All the Spring Style Hose Clamps with Screw Style Clamps on the Fuel System. >>Since this ... | |
| ht3813 honda riding mower | 4/13/2010 |
| Q: ive been looking for a downloadable service manuel [free if possible]. while mowing on flat ground ... A: >>You can Download Manuals (these contain Illustrated Parts Breakdowns) for this Unit from this Site ... | |
| John Deere 314 drains battery | 4/13/2010 |
| Q: my grandfather has a John Deere 314 lawn tractor, it has a 14 hp kohler, single cylinder engine on ... A: >>I Suggest you Check the Stator/Charging Coil/Alternator and Ensure it is Charging Correctly and ... | |
| Briggs and Stratton Idling Problem | 4/13/2010 |
| Q: I have a 13 year old riding lawn mower, Briggs and Stratton engine. Model = 42A707 Type = 123801 ... A: >>From your Description it Sounds like the Carburetor Requires Soaking and Cleaning. >>The Following ... | |
| mower engine power ratings | 4/13/2010 |
| Q: I have an old self propelled, walk behind, lawn mower with a 6.25 hp Briggs %26 Stratton engine. ... A: >>I Located this Information on CC to HP Conversion Online a Few Years ago; >>The Formula that works ... | |
| JD Gator | 4/12/2010 |
| Q: I have a JD Gator with engine FD620. The back spark plug does not fire. The unit does run on the ... A: >>Try Checking for Spark this Way. It Doesn't Sting as Bad. lol. >>Remove the Spark Plugs and Wrap ... | |
| Echo backpack blower | 4/12/2010 |
| Q: I have a an Echo backpack power blower model #PB413H, ser# 09055946. It starts up OK but when I ... A: >>From your Description it Sounds like the Carburetor Requires Soaking and Cleaning. >>The Following ... | |
| INTERCHANGING ATTACHMENTS BETWEEN BRANDS | 4/12/2010 |
| Q: I have a s1400 John Deere line trimmer weed wacker etc. I bought three of the attachments edger and ... A: >>I have Never had to use Other Attachments with Any of my Units that were Not for the Unit itself. ... | |
| Flooded Carb | 4/12/2010 |
| Q: I have a 20 year old, relatively lightly used (20 hrs per year) Kawasaki FB46V 12.5 engine. ... A: >>I have tried the 44K and have Found that it Does Work Better on 2 Cycle Engines than on the 4 ... | |
| 10 HP Kohler Carburetor | 4/12/2010 |
| Q: I have a 10 HP Kohler Engine on a Cub Cadet Mower, Model #108. Engine model # K241A, spec # 46657d. ... A: >>The Following is a Basic Instruction File I made for this. Any Input is Appreciated. I Usually ... | |
| craftsman weed eater | 4/12/2010 |
| Q: I have the weed eater model #358.791540, 17", 25cc, S/N#05070N402087. It deos't run so I take the ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| elecrotlux fl 1500 leafblower | 4/11/2010 |
| Q: i have taken the lower housing off and removed the nut holding on the blade but can not remove the ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Cub Cadet 2135 ignition module | 4/11/2010 |
| Q: John, I have a Cuc Cadet 2135 with the Kohler motor that has a bad ignition module. I have ... A: >>I'm Lost here. lol. >>You can View a Breakdown/IPL of this Unit at this Site Addy; ... | |
| parts diagram, list for jc penny sold Murray riding mower | 4/11/2010 |
| Q: I am looking for parts diagram, parts list for a Mower manufactured by Murray, sold under JC Penny ... A: >>From your Description it Sounds like the Belt you Purchased was the Wrong Width. >>Usually these ... | |
| power surge | 4/11/2010 |
| Q: My issue is with a 2003 Lawn Boy model 10324 Silver Star walk behind mower. I am frustrated with ... A: >>I am Sorry you are having so Much Trouble with this Unit. >>Usually the Lawn Boy Brand is Very ... | |
| Flooded Carb | 4/11/2010 |
| Q: I have a 20 year old, relatively lightly used (20 hrs per year) Kawasaki FB46V 12.5 engine. ... A: >>This is a Sticking Carburetor Float Needle Valve Problem. >>The Following is a Basic File I Made ... | |
| stihl 029 | 4/11/2010 |
| Q: I have a stihl 029 chainsaw that has good compression and starts easily but when you try to start it ... A: >>Have you Checked the Spark when this Happens? >>Does the Engine Start Good Once it Cools? >>How ... | |
| Troybilt Rideing mower will not engage in forward or reverse | 4/10/2010 |
| Q: My riding mower troybilt Super Bronco 42" cut 15hp briggs stratton engine will not engage in ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| engine swap | 4/10/2010 |
| Q: i recently changed out a 15hp kohler on a craftsman riding mower spec 41526 model cv155 with a 16hp ... A: >>Other than the Wiring of the Engine for the Lights, Carburetor Shut Off Solenoid, Charging and ... | |
| Getting inside the Harmony 215 | 4/10/2010 |
| Q: the lower spring on the brake cable has broken on my Harmony 215. I saw where it came from, I have ... A: >>Don't Worry. I know a Lot of People that Feel the Same Way. lol >>You can View a Breakdown/IPL at ... | |
| Small gas powered lawn mower | 4/9/2010 |
| Q: I have a small Briggs and Stratton engine gas lawn mower which starts fine, but after a few minutes ... A: >>From your Description it Sounds like the Carburetor Requires Soaking and Cleaning. >>You can View ... | |
| Walbro wt 275 | 4/9/2010 |
| Q: John, the carb is on a Ryobi 31c tiller. Gas was leaking out diaphram vent so I got a kit, cleaned ... A: >>The Brass Washer (Welsh Plug #88-171) is Removed from the Carburetor to Remove the Check Valve and ... | |
| sears weedwacker | 4/9/2010 |
| Q: I have a sears weedwacker 358.791010 I got a year ago and it sat in the garage. Now I got it out of ... A: >>This Unit is Manufactured by Poulan. >>The Breakdown at the Sears Site Addy for the Engine Shows ... | |
| 95 kohler cv15s | 4/9/2010 |
| Q: engine backfired and now only runs wide open A: >>If the Engine Backfired through the Carburetor, then >>Remove the Carburetor and Check the ... | |
| JD LT133 stalls out when hot | 4/9/2010 |
| Q: Please bear with me as I know very little about engine repair. I have a John Deere LT133 with a 13hp ... A: >>No Worries. >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| PowerMax 6.5 HP small engine | 4/8/2010 |
| Q: Currently my husband and I are building a custom mini trike. A friend gave us a PowerMax 6.5 HP ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Torque Specs for lawn mower blades. | 4/8/2010 |
| Q: Not sure how tight to make my lawn mower blades. I have a push behind and a rider anyone have any ... A: >>The Blades are Usually Torqued to 125 to 150 Foot Pounds. >>If you Hit a Snag or this Does Not ... | |
| Walbro wt 275 | 4/8/2010 |
| Q: John, the carb is on a Ryobi 31c tiller. Gas was leaking out diaphram vent so I got a kit, cleaned ... A: >>From your Description it Sounds like you may have Damaged the Check valve. >>You can View a ... | |
| Old Sears Craftsman Electric Chainsaw | 4/8/2010 |
| Q: I have an old Sears Craftsman electric chainsaw that I found in my garage and I have a few questions ... A: >>To View a Breakdown of this Unit Go to this Site Addy, ... | |
| Murray 405808x92 | 4/8/2010 |
| Q: I just bought this mower and when you start it up, it only runs at full throttle. I cannot locate an ... A: >>Locate the Carburetor. >>Follow the Solid Linkage from the Carburetor to the Governor Arm. >>Start ... | |
| Honda HT3813 Tractor Problem | 4/8/2010 |
| Q: I have a HT3813 Lawn Tractor which I purchased new in 1987 - Model GB1013 Engine No 1008511. The ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| murray riding mower | 4/8/2010 |
| Q: I got a old mower for my dad that had been sitting for a while, we replaced hoses,tires and the ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Craftsman Eager-1 engine | 4/8/2010 |
| Q: This was part of your answer for Craftsman 4.5 Eager-1 engine that had been sitting for 5 years. "If ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Craftsman 80W90 transaxle gear oil | 4/7/2010 |
| Q: ....as shown in the subject line - this isn't and engine question, but hopefully your experience can ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Lawn Boy Silver Pro lawn mower | 4/7/2010 |
| Q: I am having trouble starting the mower, it takes several tries, I prime slowly, and still doesn't ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| mower stalls | 4/7/2010 |
| Q: I have a Scott's riding mower with a Kohler command 16 engine on it. The mower starts and runs fine ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Difficult to pull starter | 4/7/2010 |
| Q: I have a Craftsman lawn mower with a B&S 128600 series engine (7 HP). It has developed a problem ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| fuel pump | 4/7/2010 |
| Q: I have a older john deere 316 tractor with the twin cylinder onan motor. It was getting no fuel past ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| solenoid or starter or just charge the battery | 4/7/2010 |
| Q: I just did some maintenance on an older Murry rider. has a 12h.p. briggs #282707-012201. Mainly put ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| sears weedwacker | 4/7/2010 |
| Q: I have a sears weedwacker 358.791010 I got a year ago and it sat in the garage. Now I got it out of ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| John Deere Alternator | 4/7/2010 |
| Q: Battery wasn't charging, got a new battery, same problem. Replace the alternator, ignition switch. ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Craftsman Snowthrower | 4/7/2010 |
| Q: The craftsman snowblower that I purchased in 2008 would not start in 2009.It started to make this ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| 9hp kawasaki john deere rx75 | 4/7/2010 |
| Q: just picked this riding mower up. No known problems other than three flats and a dead battery. When ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Snapper Walk-Behind Transmission INOP | 4/6/2010 |
| Q: Snapper model P216012 transmission failed last fall and during the winter I disassembled it and ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Which Direction? | 4/6/2010 |
| Q: Someone just told me to tip the lawn mower for cleaning so that the carborator is up. I don't know ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| 5 HP I/C Gold engine for pressure washer | 4/6/2010 |
| Q: What kind of oil should I use and how do you change it. It is a Briggs & Stratton engine and is on ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| DYT4000 Craftsman Mower | 4/6/2010 |
| Q: I have a DYT4000 mower, model #917.273280, sn 022803D003940. The freewheel control will not ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| tecumseh | 4/6/2010 |
| Q: i need to find a solid state ignition for a hh 100 tecumseh in a jd lawn mower or can it be ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| JD stx38 hydro oil change tuff torq k-50 | 4/6/2010 |
| Q: John, I need to change oil in the hydrostatic drive on my STX 38. Is there a drain plug and what ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Briggs tiller | 4/6/2010 |
| Q: I have a Troy built tiller with a Briggs model 134292-1664-01. Fabulous machine. Had the connecting ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| ohv17 not getting fuel | 4/6/2010 |
| Q: John I am working on a Tecumseh OHV17 I am getting spark but no fuel. I have put new fuel line and ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| MTD model 609 riding lawnmower 42" 17hp Intek | 4/6/2010 |
| Q: Recently, I had to replace the solenoid on my tractor, which I did. And I clipped the wiring from ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Engine Oil | 4/5/2010 |
| Q: I changed the oil in my Murry 12hp B&S engine. After mowing for a little while the engine started ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| craftsman Lt1000 | 4/5/2010 |
| Q: Hey Robert, I have had a bit of a problem with my Craftsman LT1000 with an Intec 18ohv B&S. My ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| mower wont run with air filter on | 4/5/2010 |
| Q: i have a craftsman 6.5hp eager1 mower,the only way it will run is with air filter off.i completly ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Gasoline & oil | 4/5/2010 |
| Q: I have Troy-Bilt 42" riding lawn mower. I went to service it and found gasoline in the oil, it over ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| torque specs | 4/5/2010 |
| Q: sears m#917.2736403 18.5hp,what are the head bolt torque specs? Thank You Mike A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| John Deere X304, No spark due to safety cutoff. | 4/5/2010 |
| Q: I am trouble shooting my 2008 JD X304 tractor that wont start (only 36 Hrs on the clock) , I have ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| John Deere LT 155 | 4/5/2010 |
| Q: We have a John Deere LT 155 with a hydrostatic trans. The mower worked well until a day or so ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| clutch removal cub cadet 5075 | 4/5/2010 |
| Q: how do you remove the clutch on a 2008 cub cadet trimmer, model # 5075 ? it seems to be pressed on? ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Cub Cadet 1641 | 4/4/2010 |
| Q: we need to change the oil in our Cub cadet 1641 v-twin & need to know how much oil to use A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| ignition switch wiring | 4/4/2010 |
| Q: if you would need more info let me know but that is what i went with to the local hardware store ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| fly wheel scotts s2554 mower | 4/4/2010 |
| Q: I am looking for a fly wheel for my mower all th magnets got chewed can you help? A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Shifter hard to shift. Craftsman riding mower. | 4/4/2010 |
| Q: I have a Craftsman mod# 502.255092 10hp 30" riding mower. It will shift into all forward gears and ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Scotts S1742 wont start | 4/4/2010 |
| Q: Mr. Bridges,the tractor has a Briggs INTEK OHV Mod#311777 Type#0143-E1 and Code#991116ZE. I last ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| B&S coil | 4/4/2010 |
| Q: B&S engine model 130292, Type 0159. Are the magneto, coil, and armature all the same part with just ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| McCulloch electric chain saw | 4/3/2010 |
| Q: You recently gave me some great ideas about finding a switch trigger for my ancient McCulloch ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| mower tire | 4/3/2010 |
| Q: I have a signature 2000 elite tm 12 1/2 hp, model # 286707, type 042001, code 91081311. I am try to ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| John Deere 445 | 4/3/2010 |
| Q: John, I have a 1994 John Deere 445 with a 22 hp Kawasaki fuel injected, liquid cooled motor. It has ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Echo Gas Trimmer | 4/3/2010 |
| Q: I have a Echo gas string trimmer. I have replaced the fuel lines,fuel filter,carb kit,primer ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Oil changing question | 4/2/2010 |
| Q: I have a John Deere GX75 with a 9hp Kawasaki engine FC290VFS10 E-E-NOFC290VA02820, could you tell me ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Kawasaki, weak spark | 4/2/2010 |
| Q: Have a model RB460V 101648 ON JD165. Won't Start, weak spark. Sanded flwyheel outside still no fire. ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| leaking oil | 4/2/2010 |
| Q: Your question was "Good morning Mr. Dunn, I have a craftsman 700 lawn mower 190cc, key start or ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| leaking oil | 4/2/2010 |
| Q: Your question was "Good morning Mr. Dunn, I have a craftsman 700 lawn mower 190cc, key start or ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Small Honda Engine Wont Start | 4/2/2010 |
| Q: I have a reel mower with a 4 stroke small Honda engine, I recently tipped it side way to clean it, I ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| John Deere backfiring | 4/2/2010 |
| Q: "I have a john Deere 265 and it will not start. I think that there are two problems. 1st There is ... A: >>Sorry for the Delay. I have been Unable to Answer Questions Due to Health Issues. Thanks for ... | |
| Honda GVC 160/190 | 4/1/2010 |
| Q: I'm an owner of a Karcher 2600 pressure washer with the above Honda engine. There is a cover on ... A: >>The "OHC" means "Overhead Cam" and "OHV" means Overhead Valves. >>Since this is a Honda, you can ... | |
| chainsaw | 4/1/2010 |
| Q: i have a poulon chainsaw model 2150 family XPWES 0424CS:EM that revs way to high but it wont adjust ... A: >>From your Description it Sounds the Carburetor may Require Soaking and Cleaning. You can View a ... | |
| leaf blower | 4/1/2010 |
| Q: i have a still leaf blower model #BG72 the only other numbers i can find are stamped into the ... A: >>From your Description it Sounds like; 1- the Muffler Spark Arrestor Screen is Clogged and Requires ... | |
| Poulan Chainsaw gas to oil mix | 4/1/2010 |
| Q: What is the gas to oil mix for a Poulan 34cc/16" chainsaw and if it is 40 to 1 what does that mean? A: >>Sorry for the Delay, but I had a Family Emergency come up and it kept me away all day. I am ... | |
| weed eater gti 19t | 4/1/2010 |
| Q: how do i set the idle to the right setting A: >>The Following is the Instruction File for Setting the Air Mixture Screws. Any Input is ... | |
| mower blades | 3/31/2010 |
| Q: I have a older Comm. john deere 48" walk behind mower with 14hp kawasaki motor pull start. ... A: >>Sorry for the Delay, but I had a Family Emergency come up and it kept me away all day. I am ... | |
| Kawaski FD661D | 3/31/2010 |
| Q: My engine just locked up in my 2000 Scag. We are going to replace it with a new one. My question is ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Blown Kawasaki FC540V | 3/31/2010 |
| Q: I just picked up a John Deere 265 with a Kawasaki FC540V. The engine is destroyed internally and ... A: >>Sorry for the Delay, but I had a Family Emergency come up and it kept me away all day. I am ... | |
| Tecumseh 19HP won't start | 3/31/2010 |
| Q: I have a Stanley riding mower model# 425605x692A with a Tecumseh 19HP engine model#TVT691,Enduro ... A: >>Sorry for the Delay, but I had a Family Emergency come up and it kept me away all day. I am ... | |
| Wizard Tiller | 3/31/2010 |
| Q: Need Reverse belt and installation diagram. Was told mfg was Gilson which was bought out by Toro. ... A: >>Sorry for the Delay, but I had a Family Emergency come up and it kept me away all day. I am ... | |
| Bolens BL410 2 cycle cultivator | 3/31/2010 |
| Q: The pull cord broke on my cultivator. I don't know how to remove the clutch rotor assembly to access ... A: >>Sorry for the Delay, but I had a Family Emergency come up and it kept me away all day. I am ... | |
| Brigs 8 hp | 3/30/2010 |
| Q: Model # 195422 Type 112801 I just picked this blower up and its a crop duster. Took the head off and ... A: >>The Following Site Addy will give you the Engine Specification; ... | |
| troy bilt riding mower will not start | 3/30/2010 |
| Q: troy bilt riding mower Model 809 garden tractor model # 14ay809p063.When I turn the key the mower ... A: >>This could be a Starter Problem, a Valve Adjustment Problem, or a Sticking Sheave/Pulley Problem. ... | |
| Self propel | 3/30/2010 |
| Q: John, I am going to replace the self propel cable on a Toro Model 20016 SN 240000001-240999999). ... A: >>On Most of these Units the Transmission is Designed to Pivot and be Pulled by a Spring at the End ... | |
| Auger doesn't turn -- is my gearbox broken? | 3/30/2010 |
| Q: 887990 9 HP/29 " Dual Stage Snowthrower. During our last big snowstorm, I lent my machine to my ... A: >>No Worries. It is Better for me to have too much Information to Base my Answer on than Not Enough. ... | |
| Craftsman Snowblower | 3/29/2010 |
| Q: I purchased a Craftsman in 2008 and used it about 3 times that winter. When I tried to start it in ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| MTD operating manual | 3/29/2010 |
| Q: We bought a used MTD rear tine tiller which did not caome with a manual. It is model #135202 Type ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Echo | 3/29/2010 |
| Q: I have a an Echo backpack power blower model #PB413H, ser# 09055946. It starts up OK but when I ... A: >>From your Description it Sounds like the Carburetor Requires Soaking and Cleaning. >>You can View ... | |
| Kipor KGE 3000 TI (AKA 2600 TI) | 3/29/2010 |
| Q: My Kipor generator will start and run normally without a load, if I place a small load, about 7.5 ... A: >>From your Description it Sounds like the Carburetor Requires Soaking and Cleaning, The Crankcase ... | |
| Craftsman II Snow Thrower 536.884900 | 3/29/2010 |
| Q: I just got a Craftsman II Snow Thrower 8/25 Model number 536884900, 8 speed (6 forward 2 ... A: >>The Sites Listed have Assorted Lawn and Garden Product Parts and Accessories. The Actual Site Addy ... | |
| toro mower will not push forward | 3/29/2010 |
| Q: my Toro 20016 (2002) mower front right wheel locks up when i push it forward. it works fine if I ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| John Deere 445 | 3/29/2010 |
| Q: John, I have a 1994 John Deere 445 with a 22 hp Kawasaki fuel injected, liquid cooled motor. It has ... A: >>If you use this Unit on a Daily Basis, then a New Engine would be the Best way to Proceed. If it ... | |
| Chainsaw fuel mix ratio | 3/28/2010 |
| Q: I have refurbished a 1972 Mini-Mac 1 chain saw. The saw has not been used in some time. As I ... A: >>Yes, the 50:1 ratio Oil Mix should Not Harm the Old McCulloch Saw. >>All Two Stroke Engines will ... | |
| valve adjsutment on John Deere lawn tractor | 3/28/2010 |
| Q: I have a John Deere tractor Model LX277AWS with a Kawasaki 17hp twin v engine - engine model # is ... A: >>The Following is a Basic File I made for Setting the Valve Clearances on OHV Engines. Any Input is ... | |
| id motor | 3/28/2010 |
| Q: trying to id this motor all i see on it is zendah 1480 this is on the bottom of the cylinder. the ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| manual | 3/28/2010 |
| Q: i have a sears rotospader model 106785294050 with a briggs 5 vertical. do you have a manual for the ... A: >>To View a Breakdown of this Unit Go to this Site Addy, ... | |
| Tecumseh trimmer | 3/28/2010 |
| Q: We have a "big wheel" trimmer with a tecumseh 5hp engine. It has been sitting for awhile and when ... A: >>If the Engine has been Sitting a Long Time, then the Carburetor will have to Soaked in order to ... | |
| Roto Spader | 3/28/2010 |
| Q: I have a David Bradley Roto Spader 785-30001 and I cant find any info on it. Can you lead me in the ... A: >>This Site Addy should Help; http://www.davidbradley.net/ . >>Hope this Helps. Let me Know What ... | |
| Craftsman II Snow Thrower 536.884900 | 3/27/2010 |
| Q: I just got a Craftsman II Snow Thrower 8/25 Model number 536884900, 8 speed (6 forward 2 ... A: >>You can Use the Site Addys at this Site Addy; http://www.yetmans.mb.ca/antiques.html to Search and ... | |
| Honda HRB216TDA, stops every 2-3 minutes | 3/27/2010 |
| Q: I have a Honda lawn mower model HRB216TDA. It starts up just fine w/o any problems and runs for 2-3 ... A: >>Did you Check the Gas Flow From the Tank to the Carburetor? Sometimes the Inside of the Fuel line ... | |
| blade belt replacement | 3/27/2010 |
| Q: My belt that runs my blades on the deck of my stx38 broke. The deck is yellow. How do I move the ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| "91 tor wheel horse 520-h with no spark | 3/27/2010 |
| Q: the mower info model#4120oe02 serial#1032627 motor info p220g-1710955c serial#(D or 0 can't ... A: >>From your Description it Sounds like a Safety Switch has a Bad Connection or Requires Replacing. ... | |
| Carberator linkage on a Briggs&Straton INTEK 17HP OHV engine | 3/27/2010 |
| Q: John Deere L100--After removing the carburetor and cleaning I have forgotten how the linkage ... A: **The Throttle Cable Attaches to the Throttle Control Bracket. The Cable Moves a Slide that Moves a ... | |
| B&S serial number | 3/26/2010 |
| Q: where can i go to find the break down ( meaning) of serial numbers on Briggs & Stratton engines? ... A: >>The Following is an Example of Interpreting Date Code 6206282: >The First Two Digits (62) Denote ... | |
| Snapper Drive Disk | 3/26/2010 |
| Q: I am trying to fix my Snapper LT16002 lawn tractor. The drive disk went bad to the point where there ... A: >>The Drive Disc should Not be Loose. >>You can View a Breakdown/IPL at this Site Addy, ... | |
| tecumseh ohv125-203023B | 3/26/2010 |
| Q: i got a old craftman lawnmower with tecumseh ohv125-203023B. put starter on, it was running. now i ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| small engine | 3/26/2010 |
| Q: REf; Honda Harmony riding mower 11hp clutch reg transmission I purchased from estate sale machines ... A: >>You really have Only 2 Choices when a Small Engine Sits for a while and the Carburetor is Causing ... | |
| oil spitting out of the carborater | 3/25/2010 |
| Q: I started my lawn tractor and oil started spitting out of the carburetor. I did not change or add ... A: >>This is Usually caused by an Overfilled Crankcase due to; 1- Too Much Oil Added to the Crankcase. ... | |
| 1985 EZ-Go Golf Cart | 3/25/2010 |
| Q: Two days ago, we bought a 1985 EZ-Go Golf Cart, and it was running beautifully. It had approximately ... A: >>From your Description it Sounds like the Oil to Gas Ratio is Way too Rich with Oil. >>I Spoke with ... | |
| RPM surge | 3/25/2010 |
| Q: I have a Honda 3813 and when it gets warmed up the engine rpm's will all of a sudden shoot up to ... A: >>If I Understand your Question and Comments; you have already Opened the Crankcase and Checked the ... | |
| Tecumseh Mini Tiller | 3/25/2010 |
| Q: I have a TC200 2044E 9354G Mini Tiller. tiller been sitting up, decided to use it again. The ... A: >>Sorry about that. >>You can View a Breakdown/IPL of the Carburetor at this Site Addy, ... | |
| Turf T11 tiller model 5056-73 | 3/25/2010 |
| Q: I am looking for a website where I can order a parts manual for the above front tine tiller. It ... A: >>This is an Old MTD Model Number. **Example of Complete Information: Frame Model 5052 34 4742 S/N ... | |
| Murray20" | 3/24/2010 |
| Q: Murray20 "posterior ensacado cortacésped 3n 1 COMBO 6.0hp de motores de aviación Tengo una máquina, ... A: Hola, Luis Parece como si haya una unión mala en el interruptor de seguridad, pero a fin de ser más ... | |
| Jacobsen 22 greens mower | 3/24/2010 |
| Q: I have a Jacobsen 22 greens mower with a 2 stroke engine (model A984H) and I am looking for a ... A: >>Sorry for the Delay. They are Installing Sewer Lines in the Area and have been Hitting Water Lines ... | |
| Honda Lawnmower | 3/24/2010 |
| Q: I have a 2005 Honda Harmony II self propelled mower and it has leaked a lot of oil from the ... A: >>Sorry for the Delay. They are Installing Sewer Lines in the Area and have been Hitting Water Lines ... | |
| tecumseh | 3/24/2010 |
| Q: My father is trying to repair some old (really old) 3 wheeler. It has no name brand. It has a 7hp ... A: >>From your Description it Sounds like the Carburetor was Not Soaked but Cleaned with Spray Cleaners ... | |
| Honda Engine | 3/24/2010 |
| Q: Our GCV 160 5.5 Honda on a Billy Goat will start with starter fluid and will only keep running as ... A: >>You are Very Welcome and I am Glad I am Able to Assist you and the Other Questioners. >>I Looked ... | |
| Help with My Bolens | 3/23/2010 |
| Q: My Bolens riding mower sometimes will not move when put in gear. Can you help thanks Model ... A: >>When the Unit will Not Move, is the Clutch Pedal/Lever Returning to it's Correct Position or is it ... | |
| craftsman mower | 3/23/2010 |
| Q: I have a craftsman 6.75 horsepower 21" cut power-propelled mower. The model # is 917.370721. When ... A: >>From your Description it Sounds like the Wheel Assemblies Require Cleaning. >>To View a Breakdown ... | |
| Tecumseh Mini Tiller | 3/23/2010 |
| Q: I have a TC200 2044E 9354G Mini Tiller. tiller been sitting up, decided to use it again. The ... A: >>You can View a Breakdown/IPL of the Carburetor at this Site Addy, http://69.16.165.8/ and Select ... | |
| Briggs Intek 18.5 OHV | 3/23/2010 |
| Q: Motor smokes heavy when engine is under a load.Runs OK other wise. Is it the head gasket? A: >>You can View a Breakdown/IPL of the Engine at this Site Addy; ... | |
| MTD mower/w gcv160 engine (1995) | 3/22/2010 |
| Q: mower starts speraticaiiy, will run a few seconds then quit. was told by a shop that the govoner was ... A: >>From your Description it Sounds like a Carburetor Problem, Not a Governor Problem. >>Hard to Start ... | |
| tillers | 3/22/2010 |
| Q: I'm trying to prepare a vegetable garden. i never used a tiller or cultivator. looking for a tool to ... A: >>Some People Prefer the Craftsman Tillers/Cultivators and Others Prefer the Ardisam Earthquake ... | |
| RX75 john deer mower won't crank | 3/22/2010 |
| Q: After 28 years of reliable operation, with proper care and maintenance, my John Deere RX75 riding ... A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| Kohler engine, oil filter removal | 3/22/2010 |
| Q: John, I have a Kohler "Courage 20" engine in a Husqvarna riding mower and am trying to ... A: >>From your Description it Sounds like the Filter was Tightened too Tight when it was Replaced last ... | |
| Rototiller engine | 3/22/2010 |
| Q: I have a Sears rototiller about 33 years old. It will start but only runs for about 35 seconds then ... A: >>You are Correct in your Diagnosis. The Carburetor Requires Soaking and Cleaning and Possibly a New ... | |
| JD 445 starting problems | 3/21/2010 |
| Q: I have a John Deere 445 that was running fine all winter long. It is I believe a 1995 with 596 ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| 6.5 hp B&S starts fine wont stay running | 3/21/2010 |
| Q: Craftsman tiller model# 917.294482 6.5hp intek Briggs & Stratton Family 4BSXS.2051HF 275821 Tiller ... A: >>From your Description it Sounds like the Carburetor does Require Soaking and Cleaning, the Head ... | |
| Honda Engine | 3/21/2010 |
| Q: Our GCV 160 5.5 Honda on a Billy Goat will start with starter fluid and will only keep running as ... A: >>From your Description it Sounds like the Carburetor Float Needle Valve is Stuck and has Stopped ... | |
| johndeer L110 lawnmower | 3/21/2010 |
| Q: I read your answer to the reason my L110 wont start. Its as your other client explained. Stopped to ... A: >>If he had it Running in 5 Minutes, then a Battery Cable May have been Loose and Required Cleaning ... | |
| craftsman power loss | 3/21/2010 |
| Q: John I have a 21hp Craftsman that has me stumped. Last year, it blew a head gasket and while they ... A: >>As you may have now Realized, the Valve Clearance on the OHV Engines are Critical and must be as ... | |
| Briggs & Stratton Replacement | 3/21/2010 |
| Q: Can you please tell me what replacement motor I would choose for my MTD tiller? It currently has a ... A: >>You can Usually Replace Tiller Engines with Any OEM (Briggs, Tecumseh, Honda, ect) that has the ... | |
| engine trouble | 3/20/2010 |
| Q: Engine Info Model# 283707 type # 0139 01 turns over fine, gas wont ignite (spark plug not the ... A: >>From your Description it Sounds like a Bad Safety Switch or Connection to a Safety Switch. >>The ... | |
| Tecumseh Mini Tiller | 3/20/2010 |
| Q: I have a TC200 2044E 9354G Mini Tiller. tiller been sitting up, decided to use it again. The ... A: I Require the OEM (Walbro, Zama, ect) and the Model Numbers Off the Carburetor. With these I can ... | |
| 18.5 briggs & stratton | 3/20/2010 |
| Q: I am replacing a head gasket and I have forgot to mark which of the push rods goes on top. I have ... A: >>You can Locate the Correct Specifications (torque specs, valve specs, ect) for this Engine at this ... | |
| 17hp kawasaki engine | 3/20/2010 |
| Q: How do you replace the governor on the 17hp Kawasaki engine? A: >>The Following is a Basic Instruction File for Examining the Inside of a Small Engine and will ... | |
| Craftman woodchipper engine | 3/20/2010 |
| Q: I wonder if you can help me, My 8HP Crafstman wood chipper engine developed a knocking sound last ... A: >>The Knocking May have been the Rod (connects to the crankshaft and piston) or the Unit may have ... | |
| placeing the Cam shaft in a Tecumseh engine | 3/19/2010 |
| Q: I've got an H60-75389K on a John Deer 624 walk-behind tiller. It broke the rod and I replaced it ... A: >>There is a Mark (- or .) on the Crankshaft Gear Tooth and a Dot(.) between the Teeth on the Cam ... | |
| crafsman 32cc trimmer | 3/19/2010 |
| Q: I have Craftsman trimmer which takes acessories, I striped the clutch drum today when I hit a tree ... A: >>Remove the Upper Shaft from the Power Unit. >>Remove the Cover from Around the Clutch Assy. >>The ... | |
| craftsman power loss | 3/19/2010 |
| Q: John I have a 21hp Craftsman that has me stumped. Last year, it blew a head gasket and while they ... A: >>From your Description it Sounds like the Valve Clearances Require Setting or the Fuel Line Clamps ... | |
| B&S 311777 | 3/19/2010 |
| Q: I have a 17 HP B&S 311777. I can't get it to start at all. When I turn the key in the ignition, ... A: >>From your Description it Sounds like there is a Bad Connection at 1 of the Safety Switches, a ... | |
| honda 2hp outboard | 3/18/2010 |
| Q: Do you know where I can download a workshop manual for this? I need to remove the carb and replace ... A: >>The Model Numbers should be Similar to the Following; BK75K1, BF100, and ext. >>The Numbers you ... | |
| Wiring problem | 3/18/2010 |
| Q: I have a DeVilbiss generator powered by a 11H.P. B&S. The B&S Model#, Type,Engine Code are, 256427, ... A: >>From your Description it Sounds like a Bad Safety Switch/Sensor or a Bad Switch. >>The Yellow ... | |
| Craftsman 13 hp. 30" rider. | 3/18/2010 |
| Q: I have a used just bought Craftsman rear engine riding mower model number 502.256220 ser. no. ... A: >>According to all my Research, this Engine uses a "R N 4 C" Spark Plug. >>Other Spark Plugs may ... | |
| Locked engine | 3/18/2010 |
| Q: I have a john deere l120 with a B&S Intek 20 twin V ohv engine. It would not turn over and I ... A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| McCullough electric chain saw | 3/18/2010 |
| Q: I have an electric McCullough chain saw - EM14E - and I need the trigger switch. I've been told ... A: >>Look in your Local Phone Directory for a Local Electrical Contractor Supplier. They Usually sell ... | |
| Tecumseh 10HP stalling on incline | 3/17/2010 |
| Q: Ariens Snow Blower Model 924116-1028 Tecumseh 10HP Model HMSK 100-159468X. Carburetor I believe is a ... A: >>From your Description it Sounds like the Gas Cap Vent and Carburetor Requires Cleaning. >>The Gas ... | |
| John Deere Hydrostatic Drive | 3/17/2010 |
| Q: fluid at the drive pulley. I pulled the pump apart replacing the seal and, apparently, got ... A: >>From your Description it Sounds like the Rotor was Installed Incorrectly. Turn the Rotor 180 ... | |
| craftsman riding lawn mower | 3/17/2010 |
| Q: I have a craftsman riding mower, model # 917.272673 LT 1000. I am having trouble cranking it, ... A: >>From your Description it Sounds like you have a Couple of Problems here. >>1- The Valve Clearances ... | |
| TORO 6.5 HP Lawn Mower starts and stops | 3/17/2010 |
| Q: The lawnmower starts right up, revs up real loud and then shuts off. We have checked all fluids and ... A: >>From your Description it Sounds like the Carburetor is Starved for Fuel. This is Usually caused by ... | |
| McCullough electric chain saw | 3/16/2010 |
| Q: I have an electric McCullough chain saw - EM14E - and I need the trigger switch. I've been told ... A: >>Send me the Model Numbers Off the Unit, Please. With these I can Locate the Proper Manual and ... | |
| Carftman tiller | 3/16/2010 |
| Q: I picked up an older Craftsman rear tine tiller, 20", model #32-29977, 5 HP Briggs& Stratton engine. ... A: >>The Age of this Unit is why you cannot Locate Information on it from Sears. >>Contact this Site ... | |
| How did I break the govenor? | 3/16/2010 |
| Q: I'm putting new rings in a Briggs and Stratton 7hp motor. Its a 170402 series with a govenor. ... A: >>After Viewing the Breakdown, it Appears that the Oil Dipper May be Installed Incorrectly or you ... | |
| Kohler K181 | 3/16/2010 |
| Q: .. I have a Kohler K181 spec 30582D that I just rebuilt w/a short block. When the engine is running ... A: >>1- >>Is the Coil Gapped Correctly? >>***Anytime a Magnet that is Set to the Correct Distance from ... | |
| 18.5 briggs & stratton | 3/15/2010 |
| Q: I am replacing a head gasket and I have forgot to mark which of the push rods goes on top. I have ... A: >>The Steel Push Tube goes in the Exhaust Port and the Aluminum Push Tube goes in the Intake Port. ... | |
| honda 2hp outboard | 3/15/2010 |
| Q: Do you know where I can download a workshop manual for this? I need to remove the carb and replace ... A: >>You can View a Breakdown/Schematic of this Unit at this Site Addy; ... | |
| My Cub Cadet LT 1024 riding mower is sick. | 3/15/2010 |
| Q: Last summer my husband took it upon himself to power wash my riding mower after I used it. A week ... A: >>At First I thought you had Sent this Question to the Wrong Expert. lol. >>It Sounded like a ... | |
| Tractor brake pad change? | 3/15/2010 |
| Q: I have a sears model 917.258524 tractor and I need to change the brake pads and most likely the ... A: >>You can Remove the Deck. >>Raise and Block the Mower. >>To View a Breakdown of this Unit Go to ... | |
| Gravely Rotary Plow oil seal | 3/14/2010 |
| Q: I have an older style Gravely Rotary plow, the kind that holds 140w gear oil in the gear housing. ... A: >>I Usually Double Up on the Seals and Not Worry about Locating those Seals anymore. The Seals are ... | |
| Transaxle | 3/14/2010 |
| Q: I was talking to you about replacing the nut on our MTD in the transaxle. Were you able to get the ... A: >>If you are Lucky, then the Nut will be in the Pan of the Transaxle. >>Once Cleaned; Remove All ... | |
| Transaxle | 3/14/2010 |
| Q: I have a second hand lawn/tractor MTD 136Q665G013 (48443) (1996). When riding, the rear wheel ... A: >>First; if you happen to get a Notice that you cannot Ask Any more Follow Up Questions, then Please ... | |
| Honda HRR2163VXA Roto stop | 3/14/2010 |
| Q: The Roto Stop on my Honda lawnmower stays engaged and does not disengage. The mower starts with ... A: >>You can View a Breakdown/IPL of the Mower/Engine at this Site Addy, ... | |
| 49cc wildfire mini pocket rocket | 3/14/2010 |
| Q: last night i was fixing up my bike due to gas leaking from the float and got it fixed after 3days of ... A: >>Yes they can. >>Try this Site Addy; http://www.scooterpartsrus.com/ for Parts. >>When the Fuel ... | |
| Kohler CV490S Starter | 3/13/2010 |
| Q: I have a Kohler CV490S engine and I have to replace the starter. Iam just trying to save a few ... A: >>You can View a Breakdown of the Engine at this Site Addy; http://www.kohlerplus.com/login.asp and ... | |
| Wheel axle | 3/13/2010 |
| Q: I have a second hand lawn/tractor MTD 136Q665G013 (48443) (1996). When riding, the rear wheel ... A: >>If you Send me the Transaxle Information that is Located on a Tag in the Transaxle Housing, I May ... | |
| frozen rear wheels | 3/13/2010 |
| Q: I have a Toro Personal Pace 22" lawnmower model 20073. When I parked mower in fall everything was ... A: >>You will need to Disassemble the Wheel Assemblies. Now Try to Turn the Transmission Input Shaft by ... | |
| B&S 5hp engine | 3/13/2010 |
| Q: I know you have probably been asked this question numerous times so I apologize in advance. I have a ... A: **The Throttle Cable Attaches to the Throttle Control Bracket. The Cable Moves a Slide that Moves a ... | |
| Craftsman Tillers | 3/13/2010 |
| Q: The tiller will go in neutral and partially in reverse, but will not go in forward. The tiller won't ... A: >>To View a Breakdown of this Unit Go to this Site Addy, ... | |
| excessive gas on plugs | 3/12/2010 |
| Q: I have a Intec 6.5 B%26S lawnmower. Replaces plug started lawnmower as it ran it died down. Took ... A: >>Usually this is Due to the Carburetor Float Needle Valve Sticking and causing the Carburetr to ... | |
| kawasaki 25hp FH721 BS16-R hard to start hot | 3/12/2010 |
| Q: kawasaki 25hp FH721v BS16-R on my hustler 60inch. real hard to start hot. done spark , hot comp. ... A: >>You can View a Breakdown/IPL of the Engine at this Site Addy, http://www.emerichsales.com/ and ... | |
| Ranch King Transaxle | 3/12/2010 |
| Q: I just picked up a Ranch King rider, 7 speed, 10 hp. The transaxle will will operate in forward ... A: >>It can be 1 of Several Issues. >>There are Several Transaxles Listed for MTD (OEM for Ranch King). ... | |
| Hi I have a second-hand Masport motor Model 92908 Type 5162-03 code 86102201. | 3/12/2010 |
| Q: Thank you for all your help. God Bless Hector Hi I have a second-hand Masport motor Model 92908 ... A: >>No Worries: >>I Just Located a Used Vertical Pull Starter in the Shop. >>My Daughter and I are ... | |
| Grasshopper mower lift problem | 3/12/2010 |
| Q: I have a 928 d2 grasshopper mower. My problem is that when I try to use the lift to raise the deck ... A: >>Yes, it Might be the Relay. >>You will Need to Check the Lift Circuit First. Sticking Contacts in ... | |
| self propelled blade adapter for briggs | 3/11/2010 |
| Q: I am looking for a blade adapter for my self propelled Briggs. The briggs engine # is 6BSXS1901VH. ... A: >>The Blade Adapters a Designed Differently Depending on the Mower Deck the Engine is Mounted to. ... | |
| 2 stroke mower problem | 3/11/2010 |
| Q: i've got a Victa Razor 2 stroke mulch mower with a VSX 160 engine in it.it is less than 2 years old ... A: >>From your Description it Sounds like the Carburetor Float or Needle Valve has Stuck. When this ... | |
| Wheel axle | 3/11/2010 |
| Q: I have a second hand lawn/tractor MTD 136Q665G013 (48443) (1996). When riding, the rear wheel ... A: >>You can View a Breakdown/IPL of this Unit at this Site Addy, ... | |
| Grasshopper mower lift problem | 3/11/2010 |
| Q: I have a 928 d2 grasshopper mower. My problem is that when I try to use the lift to raise the deck ... A: >>From your Description it Sounds like a Hydraulic Pump, Hose or Cylinder Problem. >>To View a ... | |
| Model 8 Briggs engine | 3/11/2010 |
| Q: I have a Briggs model 8 engine sold by Sears. The Sears # is 500.702052, Serial # 231600. I need to ... A: >>The Older Model Briggs and Stratton Engines had the Model, Type and Code Numbers Stamped into the ... | |
| Craftsman Tractor wont shut off. | 3/10/2010 |
| Q: I have a Craftsman LT200 Lawn tractor #917.273130 with a 17hp Kolher engine. The engine won't shut ... A: >>From your Description it Sounds like a Wire to the Ign Coil has Broken or become Disconnected from ... | |
| honda small engine no spark | 3/10/2010 |
| Q: the only numbers i can find are gco 8186155. last time i started this engine it ran for about 2 ... A: >>Can you Send me the JD Model Numbers, Please. With these I can Locate the Correct Manual and ... | |
| 49 cc pocket rocket | 3/10/2010 |
| Q: want to buy a pocket rocket but owner says spark plug wont fire after sitting for months. is this a ... A: >>It can be Nothing more than Rust on the Flywheel causing a No Spark Situation. >>It can Also be ... | |
| 23hp kohler, not turning over. | 3/10/2010 |
| Q: We purchased a 52"great dane super surfer today. When we picked it up it turned on fine. We quickly ... A: >>Send me the Model Numbers Off the Unit, Please. With these I can Locate the Proper Manual and ... | |
| honda muffler | 3/10/2010 |
| Q: On 1/8/08 you offered advice for a muffler for a Honda GX160 motor, I believe that was for a ... A: >>There is No Longer a Replacement Muffler Offered by Honda that will Perform as you Require. >>I ... | |
| engine info | 3/9/2010 |
| Q: First time trying this , I am trying to help a friend to get info on a engine that is on a sears ... A: >>Sorry for the Delay. I had to Perform Upgrades to my PC and it Took a While. The PC had Not been ... | |
| weed eater | 3/9/2010 |
| Q: My weed eater (about ten years old) is getting really difficult to start. I can eventually get it ... A: larson: >>From your Description it can be Due to 1 of the Following: >>1- >>Restricted Exhaust Port ... | |
| Clutch slipping on Troy bilt power head. | 3/9/2010 |
| Q: Not sure the model number. Think it's a tb21 2cycle Troy bilt tuffy power head. I have it attached ... A: >>Sorry for the Delay. I had to Perform Upgrades to my PC and it Took a While. The PC had Not been ... | |
| Toro 832 Snowblower | 3/9/2010 |
| Q: John, I just purchased an very good condition used Toro 832 w/electric start. Two items; the 3rd ... A: >>Since you are a Good Handy Man, then the Repairs should be Fairly Simple for you to do using a ... | |
| Mantis Tiller | 3/9/2010 |
| Q: I'm a small engine hobbyist who has kept my old Mantis Tiller (SV-4B 195640) running for 14 years. ... A: >>Sorry for the Delay. I had to Perform Upgrades to my PC and it Took a While. The PC had Not been ... | |
| Snapper tractor won't start | 3/8/2010 |
| Q: My Snapper lawn tractor (LT150H33IBV)with a B & S engine (281H00) won't start. Battery is good and ... A: >>Sorry for the Delay. I had to Perform Upgrades to my PC and it Took a While. The PC had Not been ... | |
| Honda self propelled mower | 3/8/2010 |
| Q: I have a Honda HBR215 self-propelled mower that start and runs great but won't go. The serial number ... A: >>Sorry for the Delay. I had to Perform Upgrades to my PC and it Took a While. The PC had Not been ... | |
| Masport635 lawn mower recoil. | 3/8/2010 |
| Q: The recoil was jamming so i opened it and moved the spring. Assembled it.But there is a small steel ... A: >>Sorry for the Delay. I had to Perform Upgrades to my PC and it Took a While. The PC had Not been ... | |
| Kawasaki engine numbers | 3/8/2010 |
| Q: I have a Kawasaki FH430 engine. I cannot find any additional numbers to identify the engine. Where ... A: >>Sorry for the Delay. I had to Perform Upgrades to my PC and it Took a While. The PC had Not been ... | |
| Mantis Tiller | 3/7/2010 |
| Q: I'm a small engine hobbyist who has kept my old Mantis Tiller (SV-4B 195640) running for 14 years. ... A: >>The Following is a Basic Instruction File for Doing a Diagnostic on the Engine for this Problem. ... | |
| Masport635 lawn mower recoil. | 3/7/2010 |
| Q: The recoil was jamming so i opened it and moved the spring. Assembled it.But there is a small steel ... A: >>I have a Vertical Pull Start Engine in the Shop and I will have a Picture taken on Monday that ... | |
| Tecumseh engine govenor | 3/7/2010 |
| Q: a nieghbor gave a mower witha tecumseh engine. They had bent the small arm on the engine speed ... A: >>The Following is an Instruction File I Made for Setting the Governor Arm Correctly. Any Input is ... | |
| Craftsman Push Mower Won't Start | 3/7/2010 |
| Q: I have a 4.0 Craftsman20" rear disharge rotary lawn mower, model no. 917.389250. It has been sitting ... A: >>The Carburetor May Require Soaking and Cleaning, the Ign Module Shut Off Terminal (shut off ... | |
| idetification | 3/7/2010 |
| Q: i have a john Deere 314 mower i bought recently all the stickers on engine are worn off i need to ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| B&S 5HP won't start. | 3/7/2010 |
| Q: I have a Whites tiller built in '92 with a 5hp B&S. It has been setting for a few years. I tried to ... A: >>Have you Checked the Flywheel Key for Damage? >>From your Description it Sounds like the Flywheel ... | |
| fuel lines for woodsman (poulan 2.5) | 3/6/2010 |
| Q: having trouble reconnecting lines (have lines running to gas tank w/ filter hooked up, i've seen a ... A: >>Sorry for the Delay. I had to Perform Upgrades to my PC and it Took a While. The PC had Not been ... | |
| carb | 3/6/2010 |
| Q: my riding lawnmower has sat up over winter. now when i try to crank, it does not run right.the motor ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Lawnmower Transmission | 3/6/2010 |
| Q: Where can I get instructions on how to replace the transmission in a Honda 215 lawnmower? Info I ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Masport635 lawn mower recoil. | 3/6/2010 |
| Q: The recoil was jamming so i opened it and moved the spring. Assembled it.But there is a small steel ... A: >>These Model Numbers are for a Briggs and Stratton Engine. >>You can View a Breakdown/IPL of the ... | |
| Snowblower engine loses power | 3/6/2010 |
| Q: I'm trying to fix a Sears 22/5 snowblower with Tecumseh engine. Engine seems to starve for fuel when ... A: >>Thanks. I will make sure it is Added to my Files. >>Till Next Time. May All Your Mechanical ... | |
| 95 toro. transmission. model 700-039 | 3/6/2010 |
| Q: 1995 Toro proline 36'walk-behind. model 175.right side shaft on trans.wont turn.owner reports ... A: >>I am Not Aware of a Problem with the Transmissions on the Toro Unit. >>Send me the Model Numbers ... | |
| set the govenor on a briggs | 3/6/2010 |
| Q: I have been reading some of your answers and man you are strong and very complete with your answers. ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Toro diagnostics | 3/5/2010 |
| Q: The left rear wheel on my Toro personal pace model 20023 lawnmower will not turn more than a half ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| magneto spark | 3/5/2010 |
| Q: what makes magneto spark in a cub cadet rzt 22 series tractor A: >>You can View a Breakdown/IPL of this Unit at this Site Addy; ... | |
| Charging problem | 3/5/2010 |
| Q: I have a Huskee mower with a Briggs and Stratton engine,and I have to replace the battery every ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| HM100 | 3/5/2010 |
| Q: I have an HM100 Tecumseh 10hp engine. The carburetor and intake were removed and I have them. ... A: >>I am Sure you want to get the Best Service you can for as Little as Possible out of this Engine. ... | |
| Turf Till Rototiller | 3/5/2010 |
| Q: Greetings John, My brother out of Ohio asked me to search for him bushings for his Turf Till model ... A: >>The Older Unit usually take some Research to Locate Parts for them. >>You can Use the Site Addys ... | |
| old troy-bilt tiller motor locked up | 3/5/2010 |
| Q: my father in law gave me this old troy bilt tiller a few years ago, it did start when I received it, ... A: >>Send me the Model and Type or Spec Numbers Off the Engine and the Unit/Mower Model Numbers, ... | |
| BCS 205 TILLER | 3/5/2010 |
| Q: How do you remove the[ acme] engine from tiller i removed the bolts from the cover but the motor is ... A: >>Hello Croft: >>In all my Years of Servicing Lawn and Garden Equipment, I have never Serviced or ... | |
| honda gx670 | 3/4/2010 |
| Q: Here we go again. A year later and I have another issue. The engine runs great while it's cold. ... A: >>From your Description it Sounds like a Worn Valve Guide or Worn Valve Stem. >>This being an OHV ... | |
| Drive Cable | 3/4/2010 |
| Q: I replaced the drive cable on a self propelled Toro lawn mower because it had broken. I attaches to ... A: >>From your Description it Sounds like (if you have the Cable Adjust Correctly) the Belt has ... | |
| brigs and straton engines | 3/4/2010 |
| Q: i have a twin 16 I/C engine on a craftsman riding mower it has a single black wire comeing out of ... A: >>They Changed the Site Addy. I Apologize for the Inconvenience. >>For Testing the Electrical ... | |
| Rearend Swap | 3/4/2010 |
| Q: I have a Husqvarna LOGTH 2448 T (96045000300)that has a weak Hydro Gear unit. I have found a newer ... A: >>Most of the K66 Units are able to be used with the Hand Control. >>If you Hit a Snag or this Does ... | |
| JD LX 277 | 3/4/2010 |
| Q: I have a JD LX 277 Mower. After the winter it did not want to start. I replaced the 8 year old ... A: >>From your Description it Sounds like the Carburetor Requires Soaking and Cleaning. >>You can View ... | |
| brigs and straton engines | 3/4/2010 |
| Q: i have a twin 16 I/C engine on a craftsman riding mower it has a single black wire comeing out of ... A: >>Go to this Site Addy; ... | |
| Valves | 3/3/2010 |
| Q: I have Briggs 18 hp single cyclinder and the valves are out of adjustment. Which valve is which, is ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| KUBOTA T1560 TRANSMISSION OIL | 3/3/2010 |
| Q: I HAVE A KUBOTA T1560 LAWN MOWER WITH A HYDROGEAR TRANSMISSION-718-0255A-AND I'M NOT SURE WHAT TYPE ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| gas problem troy bilt cultivator | 3/3/2010 |
| Q: troy bilt 4 cycle gasoline cultivator Eng 841-010339 sn e404y35000786 Model TB144.The engine will ... A: >>No Worries. We are here to Assist. >>I Apologize for you Not being able to Contact Dave with your ... | |
| engine cut out | 3/3/2010 |
| Q: John Deere LT 155 (Kohler engine) tractor lawnmower cut out when warm. Can jou help with problem? A: >>This Problem can be Caused by 1 of the Following. I Give the Most Common Cause First and So on. ... | |
| valve adjustment | 3/3/2010 |
| Q: FD750D-CSO3 HOW ARE VALVES ADJUSTED OR CLEARENCE CHECKED.THANY-YOU! A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| chain fell off my snowblower | 3/3/2010 |
| Q: i have a Craftsman 536.906000. A couple days a go the one of the chains (the one with the extra ... A: >>This Addy should show you All the Components of this Unit. ... | |
| cub cadet motor | 3/3/2010 |
| Q: I have inherited a Cub Cadet with a Kawasaki FH661V 22.0 and the engine threw a rod. I would like ... A: >>You can Put just about Any Engine/Power Plant on this Unit. >>Make Sure the Mounting Holes are ... | |
| Briggs Stock carb setting | 3/2/2010 |
| Q: I know how to set a tecumseh back to original but I was wondering how to do it on a briggs and ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| small motor | 3/2/2010 |
| Q: mtd chipper-shredder w/5hp briggs-straton wont start. I got this used and it was in real good shape ... A: >>Without Engine Model and Type Numbers it is going to be Hard to Locate the Carburetor Kit or Any ... | |
| 1985 ez go golf cart | 3/2/2010 |
| Q: I need to know the fuel mixture for a ezgo 2 cycle golf cart. A: >>All Two Stroke Engines will use a 50 to 1 Ratio using Today's Two Stroke Oils. I once had an Old ... | |
| Murray Riding Mower | 3/2/2010 |
| Q: John, I have a Murray Riding Mower (Model 425014x92) that will not start. Battery is good and ... A: >>From your Description it Sounds like the Compression Release is Not Operating as Designed. ... | |
| Tecumseh OHV 130 compression release problem? | 3/2/2010 |
| Q: I have kept my 1984 Toro self-propelled running for 26 years. I bought a used MTD (Montgomery Wards) ... A: >>From your Description it Sounds like the Compression Release Inside the Engine has Broken/Worn ... | |
| 2006 Arctic Cat ATV | 3/1/2010 |
| Q: it will start and stall after a few seconds. No interuption in fuel line, fuel pump works gas is ... A: >>From your Description it Sounds like the Carburetor Requires Soaking and Cleaning or the Valves ... | |
| Jacobson 320E | 3/1/2010 |
| Q: I was given a Jacobson 320E recently and while using it for the first time, the auger type blades ... A: >>You can Visit the Jacobsen Site at http://www.jacobsen.com/americas?country=146 . Click on Genuine ... | |
| oil leak | 3/1/2010 |
| Q: I have a craftsman 5.5 horsepower 24-inch dual stage snowblower, model 536.887250. The problem is ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| tillsmith tiller 130292 model 0778-01 type | 3/1/2010 |
| Q: I have a very old tiller that still ran great. The motor locked up today as it was low on oil. I ... A: >>Your Local Briggs and Stratton Dealer can Assist you in Locating an Engine for this Unit. >>You ... | |
| muffler removal | 3/1/2010 |
| Q: I have removed 2 bpolts and muffler is loose but I cannot remove it.The muffler is loose but I ... A: >>What Engine is this Muffler Attached to? >>Send me the Model and Type or Spec Numbers Off the ... | |
| small motor | 3/1/2010 |
| Q: mtd chipper-shredder w/5hp briggs-straton wont start. I got this used and it was in real good shape ... A: >>According to my Search, this is a 1991 Chipper/Shredder manufactured by MTD. >>You can View a ... | |
| 1980 TORO 826 SNOWBLOWER CARB ADJUSTMENT | 2/28/2010 |
| Q: WHAT DO YOU THINK OF THIS ? MY SNOWBLOWER WAS RUNNING GREAT IN THE FALL WHEN I TUNED IT UP AND ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| how to install drive cable on toro 20005 | 2/28/2010 |
| Q: I have a new cable for my toro 20005 and don't know how to put it back on correctly. it's the cable ... A: >>You can View a Breakdown/IPL of the Mower at this Site Addy, ... | |
| walbro carburetors | 2/28/2010 |
| Q: i was given a sthill leaf blower becaus it wouldnt keep running. the guy i got it from tried to ... A: >>The Following is the Instruction File for Setting the Air Mixture Screws. Any Input is ... | |
| Troy -Bilt Snowblower Track Reinstall | 2/28/2010 |
| Q: I have a model 1028 troy bilt snowblower with track drive, the track came off on 1 side. I removed ... A: >>Go to this Site Addy, http://www.jackssmallengines.com/ and Select "Parts Look Up". Now Use the ... | |
| adjusting govenor | 2/28/2010 |
| Q: how do i adjust the govenor on a FH500V Kawasaki eng. ? I ve set the govenors on other eng.s but ... A: >>The Following is an Instruction File I Made for Setting the Governor Arm Correctly. Any Input is ... | |
| 7hp 246cc yellow body mower | 2/28/2010 |
| Q: I also have aquired an old sears craftsman rider. model # 131-96920 7 horse, 246cc 15" chain drive. ... A: >>To View a Breakdown of this Unit Go to this Site Addy, ... | |
| how to find correct auger belt. | 2/27/2010 |
| Q: i have a bolens 24" 5 hp 2 stage snow blower. model 524 serial # 07011654. i need to the replace ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| engine dies 2 ways | 2/27/2010 |
| Q: have murray model 5012 (40507x8c), have not used in a while. engine runs great but when let out ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| snowblower | 2/27/2010 |
| Q: snow blower,tecumseh engine LH195sp 5.5HP.With engine running and leaning back blower ,oil shoots ... A: >>There is a Flapper inside the Crankcase Vent Assy. >>You can Try Spray Cleaner, but the Reason ... | |
| Ctraftsman snowblower | 2/27/2010 |
| Q: 887992 model snowblower from sears. it worked fine until this morning. all of a sudden the auger ... A: >>Is the Shaft from the Engine to the Gear Box Turning? >>Has the Auger Shear Bolt/s Sheared. >>If ... | |
| Snowthrowers | 2/27/2010 |
| Q: I am not sure if you will be able to help me with this. We need to buy a snowthrower. Can you ... A: >>I Suggest you Locate your Nearest Lawn and Garden Service Center and Browse their Snow Throwers. ... | |
| instruction manual | 2/27/2010 |
| Q: Where can I get a instruction manual for a MTD Yard bug or Craftsman DRM 500? Thank you! A: >>For the Craftsman, I Suggest you Contact Outdoor Distributors, http://www.outdoordistributors.com/ ... | |
| honda gx270 9.0 | 2/27/2010 |
| Q: I have a honda gx270 9 hp motor. I got it from a compressor. My plans are to use it as a gokart ... A: >>Since this is a Honda, you can Use this Site Addy; http://www.honda-engines-eu.com/en/welcome.html ... | |
| Engine Dies | 2/26/2010 |
| Q: Honda 9 Hp GX270. Stars and runs fine. After a few minutes, engine dies. Will not restart right ... A: >>Since this is a Honda, you can Use this Site Addy; http://www.honda-engines-eu.com/en/welcome.html ... | |
| 10 horse power motor | 2/26/2010 |
| Q: when i started the motor 2 weeks ago it started rite up. now i tried to start it up and it keeps ... A: >>Have you Hit Anything with the Blades or Caused the Engine to Suddenly Stop? If No, then >>Is this ... | |
| MTD Snowblower - engine seized - ? | 2/26/2010 |
| Q: First let me say I have read several of your posts and have learned quite a bit! You sound like a ... A: >>Remove the Spark Plug and Turn the Engine. **Watch Out!! You Might get Sprayed with Oil that is ... | |
| carburetor adjustment | 2/26/2010 |
| Q: I just cleaned carb on Briggs and stratton 8 hp(snow blower). Carb has 3 adj screws..2 on carb body ... A: >>If you Move the Governor Arm, does the Engine Speed Change? >>Did you Put the Governor Linkage in ... | |
| toro walk-behind problem | 2/26/2010 |
| Q: have older 44 inch toro walk-behind. dont know model#. its one that has big grass catcher attached ... A: >>**If you Need Assistance in Locating the Model Numbers, then You can Go to this Site Addy; ... | |
| JD LX 277 | 2/25/2010 |
| Q: JD LX 277 w/Kawasaki engine. while mowing the lawn the motor acts likes it missing or flooding and ... A: >>Have you Performed the Carburetor Solenoid Check? The Solenoid will cause the Engine to Perform as ... | |
| Tecumseh HSSK50 Won't Stay Running | 2/25/2010 |
| Q: I have an MTD snowthrower with a Tecumseh HSSK50 engine. It has run well for 8 years. The third ... A: >>From your Description it Sounds like; 1- The Valve Clearance Require Setting. 2- The Head Bolts ... | |
| carburetor adjustment | 2/25/2010 |
| Q: I just cleaned carb on Briggs and stratton 8 hp(snow blower). Carb has 3 adj screws..2 on carb body ... A: >>The Following is the Instruction File for Setting the Air Mixture Screws. Any Input is ... | |
| Toro Ride-On Mower 14-38 HXL Mod. 71217 Ser. No. 6901007 | 2/24/2010 |
| Q: You helped us a couple of years ago, this problem is almost identical. Our Ride On mower refuses to ... A: >>From your Description it Sounds like a Safety Switch is Bad or is Not Making Proper Connection. ... | |
| Stihl 260 pro | 2/24/2010 |
| Q: "John I have a new Stihl 260 Pro when I start it up it hesitates and you have to feather the ... A: >>I have Found that the OEMs of Chainsaws have Lessened the Amount of Oil Going to the Bars and I ... | |
| dirtbike help | 2/24/2010 |
| Q: hey ok i have a old 2 stroke suziuki rm 80 dir bike to start i have to run and kick in first its ... A: >>Send me the Model and Type or Spec Numbers Off the Engine, Please. With these I can Locate the ... | |
| JD LX 277 | 2/24/2010 |
| Q: JD LX 277 w/Kawasaki engine. while mowing the lawn the motor acts likes it missing or flooding and ... A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| Screaming in Engine | 2/24/2010 |
| Q: I have a 10.5 HP Tecumseh Snowblower motor on my snowblower. Yesterday i When i started, it started ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| job qoute(pricing) | 2/24/2010 |
| Q: I just would like a general idea of what a repair shop would/should charge to replace the rings on ... A: >>****This is a Hard Question to Answer and I Usually do Not Quote Prices, but more and more I am ... | |
| Snowblower Drive Belt | 2/23/2010 |
| Q: Simplicity Model 870 02982 Snow Blower. It is a Briggs 7 h.p. Snow-Away, 28" clearing path. Drive ... A: >>Are you Sure the Pulleys are in Line with Each Other? If the Drive Pulley is Not in Line with the ... | |
| Troy-Bilt 13AX60TG766 Wont Start | 2/23/2010 |
| Q: I have a Troy-Bilt 13AX60TG766 that blew a fuse awhile back and now wont start. I replaced the fuse ... A: >>You can View a Breakdown/IPL of this Unit at this Site Addy, ... | |
| carburetor | 2/23/2010 |
| Q: i have a scotts john deer modelcv16s 1642 it runs wide open when you put it on slow it just started ... A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| Honda motor on a pressure washer | 2/22/2010 |
| Q: I have a Karcher pressure washer with a Honda GC 190 6.0. I started it, it ran for 30 seconds and ... A: >>Does the Engine Turn with the Spark Plug Removed? If No, then the Engine has Seized. >>You can ... | |
| Mower engine quit | 2/22/2010 |
| Q: Craftsman Mod# 536.270280 Auto 13.5 HP I/C 30". serial # 75201053311L298 Ran great at for first ... A: >>Make Sure No Wires are Broken or have Bare Places that Might Ground the Coil. >>To View a ... | |
| points | 2/22/2010 |
| Q: How do i set the points? Wisconsin S8D The wisc. part # is YQ12.This includes a new condenser. The ... A: >>The Following is the Instruction File I Made for Removing the Flywheel and Replacing the Point Set ... | |
| CCR2000 Backfire after a few minutes | 2/22/2010 |
| Q: I have a 1993 Toro CCR2000 model 38180, serial no. 3909332 It runs for about 5 minutes and then ... A: >>From your Description it Sounds like the Rings May Require Replacing or they have Frozen/Stuck to ... | |
| mtd tiller | 2/22/2010 |
| Q: i am working on a mtd chain drive tiller, model is 91212 type 0219 01 code 95041303. the motor ... A: >>From your Description it Sounds like the Carburetor Requires Soaking and Cleaning. You May also ... | |
| b48m | 2/21/2010 |
| Q: i have a case 448 with a onan engine it seems to stall out. i thuoght it was the fuel pump but you ... A: >>You can use an Electric Fuel Pump. The Pump has to be Rated at 2 to 4PSI and No More that 6PSI. ... | |
| Gravely snowblower | 2/21/2010 |
| Q: Do you know where I might be able to find a service/repair/IPL manual for a Gravely 524 snowblower? ... A: >>You can View a Breakdown of this Unit at this Site Addy; http://www.gravely.com/ and Select Parts ... | |
| Lawn Boy 1998 snow thrower model 522R | 2/21/2010 |
| Q: How do I remove and replace the left hand auger to replace the one that broke. I will probably ... A: >>You can View a Breakdown/IPL of this Unit at this Site Addy, ... | |
| Replacing 57994 lever assembly for snow thrower | 2/21/2010 |
| Q: I note you recommend re-welding lever assembly arm as a possible fix. If that doesn't hold, what is ... A: >>If you have the Model Number, then Usually the Following Site Addy has a Breakdown of this Unit. ... | |
| Governor spring and governed idle spring connections | 2/21/2010 |
| Q: By cleaning the carburetor of Briggs%26Stratton 10A902 I removed the governor spring and the ... A: **The Throttle Cable Attaches to the Throttle Control Bracket. The Cable Moves a Slide that Moves a ... | |
| JD 318 steering section | 2/21/2010 |
| Q: At times after cutting a while fluid gushes out the center of the steering wheel. I have been told ... A: >>From your Description it Sounds like a Blown/Bad Seal in the Power Steering Control Valve. >>You ... | |
| lawn mower motor | 2/20/2010 |
| Q: i'm looking for a new mower and cant decide on a briggs motor or a kawasaki motor can u give me some ... A: >>I am Sorry to Say the Engines Do Not Matter that much anymore. The Unit the Engine is Powering is ... | |
| craftsman walk behind mower | 2/20/2010 |
| Q: i have a craftsman walk behind mower with a 6.75hp tecumseh engine.i believe this engine is a vlv ... A: >>Have you tried Soaking and Cleaning the Carburetor? >>I Suggest you try Cleaning the carburetor ... | |
| Hayward web address | 2/20/2010 |
| Q: John, I tried to go to the hyperlink you gave: ... A: >>Try the Following Addy; >>Since this is a Honda, you can Use this Site Addy; ... | |
| PTO blows fuse | 2/20/2010 |
| Q: Toro 268H when the PTO is engaged the fuse blows - I tried a higher amp fuse worked for a couple of ... A: >>Check the Ground Wire at the PTO Connector and Ensure the PTO has a Good Ground. >>The PTO May ... | |
| Homelite Chainsaw | 2/20/2010 |
| Q: My 1998 Homelite chainsaw is not oiling the chain. 33cc engine Model # is wore off. A: >>Have you Cleaned Out the Metering Port with a Torch Tip Cleaner Rod or a Straight Pin? If No, then ... | |
| Toro 6.5 hp 20016 self-propelled | 2/19/2010 |
| Q: Just wondering what kind of job it is to replace the gear box that operates the self-propelling of ... A: >>To Me it's a Simple Job and Takes about 2 Hours is Everything comes Apart Fairly Easy. >>Go to the ... | |
| John Deere LX-288 | 2/19/2010 |
| Q: This mower was left behind from some of our renters. The mower runs good but when you engage the ... A: >>Check the Belt Routing and make Sure the Belt/s is/are Not Riding on a Belt Guard. >>Have you ... | |
| chainsaw blade oilers, automatic | 2/19/2010 |
| Q: I get by with small engines but am far from an expert. this has to do with the automatic oilers on ... A: >>Every Chainsaw i have Purchased since 1996 has had the Same Problem. >>I have found the Best Cure ... | |
| snow blower | 2/19/2010 |
| Q: A neighbor gave me a snowblower after he ran over his welcome matt with it. He said it ran for a ... A: >>Remove the Spark Plug and Turn the Engine. If the Engine Turns Freely, then Remove the Flywheel ... | |
| Fuel line routing for craftsman weedwhacker | 2/19/2010 |
| Q: I've found a couple different suggestions online for fuel line routing on a 1995 craftsman 21cc ... A: >>I Misspoke when I said Filter. The Filter is in the Tank and there is another Filter/Screen in the ... | |
| John Deere Model 80 | 2/18/2010 |
| Q: I am at wits end. I have a JD Model 180 Lawn Tractor. It has the Kawasaki FC540V 17HP motor, ... A: >>I Reviewed the Breakdown for this Unit and the Carburetor May or May Not have a Fuel Shutoff ... | |
| Craftsman Snowblower Drive problem | 2/18/2010 |
| Q: John, Hope you are doing well. I have a Craftsman Snow Thrower # 536.886220 (12 yrs old) that I ... A: >>If the Unit is Not Jumping when trying to Move, then it is Usually the Friction Disc. If the Unit ... | |
| Blower carb adjusting tool | 2/18/2010 |
| Q: I have a Craftsman gas powered leaf blower which is a couple of years old. Where can I purchase the ... A: >>I have Questioned Several of the Carburetor OEM's about these Tools and have been Told that the ... | |
| engine dies and clear fuel filter is empty | 2/18/2010 |
| Q: Have Scott S1642 with Kohler Commander engine. First time to run this unit since December. Fresh gas ... A: >>First, Replace ALL the Spring Style Hose Clamps at the Carburetor and the Engine with Screw Style ... | |
| setting timing gears | 2/18/2010 |
| Q: I have a hawgty scooter made in china its JF 168 Jiangdong 5.5 hp the engine gasket was leaking oil ... A: >>There is a Mark (-) on the Crankshaft Gear Tooth and a Dot(.) between the Teeth on the Cam that ... | |
| Honda HS35 Snowblower | 2/17/2010 |
| Q: I have a honda HS35 that will not come up to full RPM with the choke off. It starts great every ... A: >>How was the Carburetor Cleaned? Was it Soaked Overnight in Carburetor Cleaner of Cleaned with ... | |
| Fuel line routing for craftsman weedwhacker | 2/17/2010 |
| Q: I've found a couple different suggestions online for fuel line routing on a 1995 craftsman 21cc ... A: >>I have seen many of these Weed Whackers and I have 1 in the Shop. >>The Primer Bulbs can Function ... | |
| Briggs | 2/17/2010 |
| Q: I have a Briggs 18HP I/C Model: 422707 Type: 1263 01 Code:9403095B While mowing a few days back the ... A: >>If the Spring Style Hose Clamps are Still being Used on the Carburetor Hose Connections at the ... | |
| Ariens st524 | 2/16/2010 |
| Q: Need info on auger belt replacement and adjustment model # 924046 serial # 011533 A: >>The Belt (Part# 07210800) is Sized to Fit and the Adjustment for Engagement is Set Using the ... | |
| SNOW BLOWER TIRES | 2/16/2010 |
| Q: I HAVE A CRAFTSMAN SNOW BLOWER THAT ONE OF THE TIRES LOSES AIR. WHEN IT DOES, THE BEAD OF THE TIRE ... A: >>I have a 1/4" Cable that Circles the Center of the Tire and when Tightened it Causes the Sidewall ... | |
| Age of craftsman equipment | 2/16/2010 |
| Q: John, I would like to find the manufacturing date of two old pieces of Craftsman lawn and garden ... A: >>Sorry for the Slight Delay; I had to do some Research on these Units. >>Can you Locate the Serial ... | |
| DT2400CS Delta Pressure Washer | 2/16/2010 |
| Q: How do you set the timing on a DT2400CS Delta Pressure Washer? A: >>The Engine is Not a Delta Component. >>Send me the Model and Type or Spec Numbers Off the Unit, ... | |
| Tecumseh carburetor rebuild | 2/10/2010 |
| Q: I have kit 631893A to rebuild carb on a 2.7 H.P. Tecumseh. 1) Does the 1" metal plate on the ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Snowflite snowblower | 1/31/2010 |
| Q: Hey i have just acquired a snowflite snowblower from my dad and i tried using it this morn and ... A: >>Sorry for the Delay, this Question was Located in the Question Pool. >>Generally the ... | |
| identify motor | 1/20/2010 |
| Q: i have a tecumseh motor that has a tag on it that reads T-643-12 and has the number 6074116 I need ... A: >>Where was the Tag Located on this Engine? I Contacted Technical Support at Tecumseh (Patrick) and ... | |
| Honda riding mower | 11/13/2009 |
| Q: I have an old Honda Riding Lawn mower - model, HT-R3009SA. I threw a spring and can't seem to ... A: >>I am Currently on Vacation and Just had a Few Minutes to Answer a Few Questions. >>This Question ... | |
| Toro snow blower with Tecsumeh engine | 9/28/2009 |
| Q: My MTD 150 snowthrower (model 31AE150-302, s/n 12267B20194)has an electric start Tecumseh engine ... A: >>Sorry for the Delay. This Question was Located in the Question Pool. I am Also on Vacation and I ... | |
| walbro wt281 carb | 9/25/2009 |
| Q: this carb has been rebuilt by a local small engine shop but it still wont work it would try to start ... A: >>Sorry for the Delay. This Question was Located in the Question Pool. I am Also on Vacation and I ... | |
| Light Switch for Snowblower | 9/15/2009 |
| Q: I have a Toro 826 LE snowblower and the light on it always runs with the motor. How would I add a ... A: >>Sorry for the Delay. This Question was Located in the Question Pool. I am Also on Vacation and I ... | |
| pressure washer | 8/6/2009 |
| Q: i have a honda pressure washer and when i crank it it seems like the engine is under a strain ... A: >>Sorry for the Delay. This Question was Located in the Question Pool. I am Also on Vacation and I ... | |
| Engine runs fast | 8/5/2009 |
| Q: Have a Craftmans 18 HP lawn tractor Model 917.272420with a Kohler Model No. CV492-27506 engine .We ... A: >>Sorry for the Delay. This Question was Located in the Question Pool. I am Also on Vacation and I ... | |
| old craftsman generator engine | 7/31/2009 |
| Q: Craftsman engine model 143-544012 i cant get the rope retractor to work properly. ok, let me ... A: >>Sorry for the Delay. This Question was Located in the Question Pool. I am Also on Vacation, but I ... | |
| Craftsman mower engine ID | 4/22/2009 |
| Q: I have a rear throw Sears Craftsman 3 hp reel mower model# 536-373730. I am trying to identify what ... A: >>The Carburetor should have the OEM Name and Model Numbers on it. >>After Viewing the Breakdown at ... | |
| John Deere 300 electrical problem | 4/22/2009 |
| Q: My john deere 300 starts with a jump(after sitting all winter)but stalls as soon as i take off ... A: >>From your Description it Sounds like there are 2 Problems here. 1->>The Stator/Charging Coil or ... | |
| Steer Shaft Removal | 4/22/2009 |
| Q: I have a Troy-Bilt Pony, model # 13AN779G766, 42" cut, 7 speed lawn tractor with a B&S 17.5 hp ... A: >>Sometimes Heat is Required to Loosen and Remove this Screw. >>If you Hit a Snag or this Does Not ... | |
| blade adaptor removal | 4/22/2009 |
| Q: I have a craftsman model number 917-378070 22" self propelled mower. I need to change the v-belt. I ... A: >>From your Description it Sounds like you are Going to have to Apply Heat to the Blade Adapter ... | |
| B&S | 4/21/2009 |
| Q: I have a B&S Model 28N707 Type 0173-01 Code 96051-13ZD It blows smoke under load and has oil in the ... A: >>From your Description it Sounds like the Crankcase is Overfilled with Oil, the Crankcase ... | |
| 152FMH engine | 4/21/2009 |
| Q: I have a problem with the 152FMH engine in my grandsons ATV. I need a service manual for this ... A: >>Send me All the Information Pertaining to the this ATV, Please. With the Make, Model and Year, I ... | |
| Honda riding mower won't stay running | 4/21/2009 |
| Q: Small ring mower, runs for about 15 seconds, took apart carb, cleaned out, problem still ... A: >>Did the Crankcase have the Proper Amount of Oil in it? >>From your Description it Sounds like the ... | |
| Tecumseh OH140 intermittant ignition | 4/21/2009 |
| Q: Sometimes I have spark, sometimes not, and it is unrelated to engine being hot or cold. The switch ... A: >>You are Correct; the Most Common Cause for Ign Module Failure is Heat. >>However, it is Not ... | |
| grasshopper mower loosing power | 4/21/2009 |
| Q: Grasshopper 721D2 (3000 hours) with Kubota D722-E diesel. The mower has started a habit of loosing ... A: >>I have Not Seen or Heard of a Problem like this before, but I am Researching it for you. >>If you ... | |
| craftsman 19.5 turbo twin cylinder riding lawn mower | 4/21/2009 |
| Q: We have a craftsman 19.5 turbo twin riding lawn mower and it won't turn over. It was running fine ... A: >>If you Jumped the Small Engine with an Automobile and the Auto Engine was Running at the Time, ... | |
| 318 misses upon startup | 4/21/2009 |
| Q: I have a 1988 318 with the P218G onan engine that misses when it is first started. After it runs ... A: >>What is the Engines Compression? >>Have you Checked the Intake Gaskets and made Sure they are Not ... | |
| John deere stx38 yellow deck transaxle | 4/21/2009 |
| Q: On a John deere stx38 yellow deck with 5 speed transmission ID# MOOSTXB125638 the pulley on top of ... A: >>From your Description it Sounds like the Transaxles Internal Drive Chain has Broken and is Locking ... | |
| Honda GCV160 on Troy-Bilt Pressure Washer | 4/21/2009 |
| Q: Please help. This engine has only been run twice (both without issue for a total of about 5 hrs). ... A: >>From your Description it Sounds like the Carburetor Float Needle Valve is Stuck and is Flooding ... | |
| rider mower broken dipstick | 4/21/2009 |
| Q: I have a Sears Craftsman 19.0 HP electric start 42" mower. Model # is 944.605730 I was checking oil, ... A: >>Thanks for the Engine Model Numbers. >>You can View a Breakdown/IPL of this Engine at this Site ... | |
| Carburetor | 4/20/2009 |
| Q: I bought a carburetor kit for my Snapper Briggs and Stratton Vanguard Engine. The model # is 261777 ... A: The Following is a Basic Instruction File for Removing Carburetors on Small Engines. Any Input is ... | |
| craftsman intek plus | 4/20/2009 |
| Q: craftsman intek plus 18.5 ohv model 917-27364 The problem is the mower seems to be running pretty ... A: >>From your Description it Sounds like the Valve Clearances May Require Setting. >>The Following is ... | |
| 9 hp vangaurd | 4/20/2009 |
| Q: It was stuck so I pulled the head and top of piston was carbon and I took off valve cover cover. The ... A: >>From your Description it Sounds like you need to Set the Valve Clearances so the Compression ... | |
| sno-trac snowblower | 4/20/2009 |
| Q: I have a sno-trac snowblower model# 315-840-502 serial # 880112 I cannot find any reference to this ... A: >>Sorry for the Delay. I have been having Issues with my PC for the Past Couple of Days. >>You can ... | |
| Eager 1 6.75 pull start rope | 4/20/2009 |
| Q: I just got Craftsman Eager 1 6.75 model# 143.996704 family type wtpxs.2071ba mower from my brother ... A: You should be Able to See a Breakdown of the Rewind Starter at this Site Addy; ... | |
| grasshopper mower loosing power | 4/20/2009 |
| Q: Grasshopper 721D2 (3000 hours) with Kubota D722-E diesel. The mower has started a habit of loosing ... A: >>Does the RPMs Drop and Stay or is it Just a 1 Time Drop in RPMs? >>Is the Engine RPMs Surging ... | |
| Craftsman riding mower/ smoking oil leak | 4/20/2009 |
| Q: I have craftsman riding mower model no.917.272751 Briggs engine model no. 31H777 type no.0202-E1 The ... A: >>If the Crankcase Breather/Vent is Operating Correctly and the Crankcase was Over Filled with ... | |
| Peerless Transaxle 205-024 | 4/20/2009 |
| Q: I have a 1997 Scotts 42 in rider with a peerless hydrostatic transaxle 205-024 and having been ... A: >>Sorry for the Delay. I have been having Issues with my PC for the Past Couple of Days. >>From your ... | |
| Sears lawn tractor 25hp kohler engine-revs | 4/20/2009 |
| Q: I have a Sears lawn tractor, 25hp Kohler engine which stays at a high rev no matter what position ... A: >>From your Description it Sounds like the Governor Arm May have Sliped on the Governor Shaft or the ... | |
| Sears Rotary Lawn Mower #917-377190 | 4/19/2009 |
| Q: Do you know how difficult it is to replace the Gear Case Assembly? Suspect that is the problem. ... A: >>If the Gear Assembly that Turns the Wheels are Good, then >>The Transmission can be Ordered as a ... | |
| 6.75 B & S craftsman self propelled mower | 4/19/2009 |
| Q: I can't get it to start. Removed air filter,OK, removed carb bowl and cleaned with carb clnr. ... A: >>You can View a Breakdown/IPL of the Engine at this Site Addy; ... | |
| starter? | 4/19/2009 |
| Q: Bridgers, I have a craftsman lawn tractor model 917.270810. The only way I can start it is by ... A: >>If you can Start the Engine by Jumping the Solenoid, then Either a Safety Switch is Bad or the ... | |
| no subject, just want to pass on info. | 4/19/2009 |
| Q: A: >>You are Very Welcome. >>Thanks Again for Using All Experts. Till Next Time. May All Your ... | |
| rider mower broken dipstick | 4/19/2009 |
| Q: I have a Sears Craftsman 19.0 HP electric start 42" mower. Model # is 944.605730 I was checking oil, ... A: >>If you Remove the Plastic Dipstick Tube you can Remove the Plastic Dipstick. >>There is No Way ... | |
| bl410 31cc mini tiller | 4/19/2009 |
| Q: I have a new tiller with a blown engine. I have contacted mtd for a replacement. They told me there ... A: >>You can Use the Site Addys at this Site Addy; http://www.yetmans.mb.ca/antiques.html to Search and ... | |
| Mower runs rough at start | 4/19/2009 |
| Q: I have Craftsman walk behind mower, model #917.377580, engine #143.986700, carburetor # 640020. ... A: >>Did you Soak the Carburetor in Cleaner or Use Spray Cleaner? >>The Following is a Basic File I ... | |
| can't keep mower running | 4/19/2009 |
| Q: I have a craftsman 917-378550 walk behind with the honda 5.5 hp engine (GCV-160-AS3A). It will not ... A: >>To Correct this Problem the Carburetor Requires Soaking and Cleaning. >>The Following is a Basic ... | |
| lawnmower stuck in gear | 4/19/2009 |
| Q: I have a murray 16.5 hp that is stuck in 1st gear whenever you start it it will take off if you let ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, http://www.outdoordistributors.com/ ... | |
| snowblower part needed | 4/18/2009 |
| Q: i have a sears snowblower model 536.885000, it has tracks.i went to searsdirect and the part i need ... A: >>This is Considered to be an Obsolete/Antique Unit. >>You can Use the Site Addys at this Site Addy; ... | |
| Incredipull Craftsman string trimmer clutch | 4/18/2009 |
| Q: I inquired earlier about removing the clutch and you said to use a bolt the size of the spark plug ... A: >>If Turning the Shaft or Pulling the Starter Rope is Not Moving the Piston, then the Connecting Rod ... | |
| Can't start tiller | 4/18/2009 |
| Q: B&S engine model 130292, Type 0159. This is about the tiller I had problems with last year. Got it ... A: >>The Magnetron Unit is a Complete Coil Assy with a Built in Ign Module (the newer mowers use this ... | |
| Craftsman Front Axel Assembly | 4/18/2009 |
| Q: I have noticed my Craftsman 917.271141 has a cracked front axel assembly (Craftsment part 154427). ... A: >>The Replacement of the Front Axle is a Simple Repair. >>To View a Breakdown of this Unit Go to ... | |
| Turf Tiger won't start. Is it the ignition switch? | 4/18/2009 |
| Q: How do I know if an ignition switch is no longer functional? The problem is that my Scag Turf Tiger ... A: >>From your Description it Sounds like the Starter of the Starter Solenoid is Bad and Requires ... | |
| Briggs Motor Swap | 4/18/2009 |
| Q: John, I'm taking out of a mower a 20 hp Briggs vertical opposed engine Models #461707-0143-E and ... A: >>From your Description it Sounds like you are Talking about the Charging Coil/Stator Wires and the ... | |
| blowing oil | 4/18/2009 |
| Q: I have a john deere with a Kholer command 13 in it.When it runs it blowes all the oil out though the ... A: >>Since All my Other Suggestions were Previously Performed, then A->>The Crankcase Breather/Vent ... | |
| Owners Manual | 4/18/2009 |
| Q: Where can I find (online) an owners manual and/or parts breakdown for a Murray Lawn Chief Model ... A: >>Murray has been Purchased by Briggs and Stratton Corp and Most Small Engine Service Centers have ... | |
| Murray mdl 30572A 11 HP Hard to put in reverse. | 4/18/2009 |
| Q: My riding mower is hard to put in reverse and when it does go in, as soon as I push in on the clutch ... A: >>The Spicer #3974 is Not in my Records or Online. >>I will have to Contact the Dana/Spicer Rep on ... | |
| Yardmachines front tine tiller quits after runing | 4/18/2009 |
| Q: I have a Yardmachines front tine tiller and had the carb cleaned recently but now it runs smooth for ... A: >>From your Description it Sounds like 1 of the Following Possible Causes. A->>The Fuel Flow is ... | |
| 6.75 B & S craftsman self propelled mower | 4/17/2009 |
| Q: I can't get it to start. Removed air filter,OK, removed carb bowl and cleaned with carb clnr. ... A: >>Here is a Basic Instruction File I am in the Process of Making. It will Might Say Mower, but a ... | |
| Can't start tiller | 4/17/2009 |
| Q: B&S engine model 130292, Type 0159. This is about the tiller I had problems with last year. Got it ... A: >>Sorry about the Confusion. Apparently I Inverted the Numbers. >>The Correct Part Number is Rotary ... | |
| kohler firing problems | 4/17/2009 |
| Q: im working on two cyl engine i unhooked the kill wire from the electronic ign...cleaned magnets on ... A: >>From your Description it Sounds like the Ign Module is Trashed. >>Connecting 12 Volts to the Kill ... | |
| lawnmower stuck in gear | 4/17/2009 |
| Q: I have a murray 16.5 hp that is stuck in 1st gear whenever you start it it will take off if you let ... A: >>Thanks for the Blessing and the Model Numbers. >>From your Description it Sounds like you have ... | |
| Kohler Courage 21 will not start | 4/17/2009 |
| Q: I am trying to get my bothers Toro Z5000 mower running. It has a Kohler Courage 21 engine and is the ... A: From your Description it Sounds like there is a Safety Switch that is Preventing the Coil from ... | |
| Craftsman Mower | 4/17/2009 |
| Q: I have a 20 plus year old Craftsman riding lawn mower. It needs a new mower deck. I have no idea ... A: With this Mower being 20 Years Old you will have to Search Web Sites to Locate a Deck for this Unit. ... | |
| replacing driven disk | 4/17/2009 |
| Q: can you please tell me how to replace the driven disk on my snapper 281016be rear engine riding lawn ... A: >>You can View a Breakdown of the Mower at this Site Addy; http://www.snapper.com/manuals/ . Enter ... | |
| Murray mdl 30572A 11 HP Hard to put in reverse. | 4/17/2009 |
| Q: My riding mower is hard to put in reverse and when it does go in, as soon as I push in on the clutch ... A: >>From your Description it Sounds like the Reverse Gear is Damaged or the Shifter Pawl/Key Requires ... | |
| toro riding mower | 4/16/2009 |
| Q: Its a 50 inch deck rider. My question is that the mower will not move or barely. Is this a belt ... A: >>From your Description it Sounds like a Belt Problem, However, >>Send me the Model Numbers Off the ... | |
| 2 cycle | 4/16/2009 |
| Q: John maybe you can help me out. I am looking for a spark plug adapter to test 2 cycle engines for ... A: >>I use the Adapter in the Compression/Leak Down Tester Set. >>You can Also have your Local Auto ... | |
| blowing oil | 4/16/2009 |
| Q: I have a john deere with a Kholer command 13 in it.When it runs it blowes all the oil out though the ... A: >>If this is an OHV Engine, then it can be 1 of the Following; A->>The Crankcase is Overfilled and ... | |
| Can't start tiller | 4/16/2009 |
| Q: B&S engine model 130292, Type 0159. This is about the tiller I had problems with last year. Got it ... A: >>From your Description it Sounds Like the Point Set Requires Replacing. >>I Suggest you Replace the ... | |
| craftsmn mini tiller | 4/16/2009 |
| Q: I have craftsman 2.0 hp mini tiller (cultivator). The tines have ceased to spin when it is under ... A: >>To View a Breakdown of this Unit Go to this Site Addy, ... | |
| John Deere 160 rough running | 4/16/2009 |
| Q: When the tractor is running just after startup it needs to be choked fully in order to continue ... A: >>You can View a Breakdown/IPL of the Engine and Mower at this Site Addy, ... | |
| POULAN RIDING MOWER REPAIR | 4/16/2009 |
| Q: WAS GIVEN POULAN RIDING MOWER RECENTLY WHICH NEEDS REPAIR. NEIGHBOR SAID NEEDED NEW BATTERY/SOLENOID ... A: >>The Starter Solenoid is Usually Located Under the Steering Tower or >>You can Follow the Large ... | |
| lawnmower stuck in gear | 4/16/2009 |
| Q: I have a murray 16.5 hp that is stuck in 1st gear whenever you start it it will take off if you let ... A: 1->>If the Shifter Linkage is Not Loose/Worn/Binding; then the Transaxle Problem Sounds Internal. ... | |
| erattic idel | 4/16/2009 |
| Q: 5 hp no matter what amount of revs the motor is doing the revs keep going up and down until motor ... A: >>The Most Common Cause for this Problem is a Restricted Passage in the Carburetor. Usually the ... | |
| Briggs & Stratton Engine | 4/16/2009 |
| Q: No fuel getting to the engine. Fuel filter is empty and line from filter back to the tank is open. ... A: >>From your Description it Sounds like you Need to Bleed the Fuel System and Prime the Fuel Pump. ... | |
| Electric PTO Clutch | 4/10/2009 |
| Q: I have a Scotts (made by John Deere)L2048 Lawn Tractor - made I believe in 2000. It has a 20HP ... A: >>Sorry for the Delay. This Question was Located in the Question Pool and I can Only Answer ... | |
| Sticking starter pulley | 3/26/2009 |
| Q: RE: B&S 170000 series engine. After doing what I hope is the final repair work on this engine, ... A: >>This Style Recoil Starter will Move Around as you Described. The Pulley is Centered on the Engine ... | |
| Honda Snowblower | 3/26/2009 |
| Q: I have a honda HS928 snowblower and it will not move in reverse or forward.Would you be able to help ... A: >>You can View a Breakdown/IPL of the Mower/Engine at this Site Addy, ... | |
| Valve adjustment on Briggs and Stratton | 3/26/2009 |
| Q: I have a Briggs 18hp Model 422707 type 1236 02. Im having a hard time cranking it over and by ... A: >>You can View a Breakdown/IPL of this Engine at this Site Addy, ... | |
| snapper 281016Be - 1999 | 3/26/2009 |
| Q: My rider no longer moves when it is 3rd gear, and is starting to slip in all other gears when i am ... A: >>From your Description it Sounds like the Drive Disc is Worn and the Tension Spring May Require ... | |
| small engine repair | 3/26/2009 |
| Q: I need directions on timing a Honda Gjaaa 6 hp engine It has a belt and plastic gear cam Thanks for ... A: >>Since this is a Honda, you can Use this Site Addy; http://www.honda-engines-eu.com/en/welcome.html ... | |
| timing on .20 h.p and vale setting. | 3/26/2009 |
| Q: i had apush rod to fall in the oil pan and i had to remove the oil pan to get it out ,,,,but ,,when ... A: >>There is a Mark (-) on the Crankshaft Gear Tooth and a Dot(.) between the Teeth on the Cam that ... | |
| Kohler Engine< | |