You are here:
| Subject | Date Asked |
| Removing Hair Dryer Nichrome Heating Coil | 2/8/2012 |
| Q: I want to remove the nichrome heating coils from my blow dryer, so that it will only blow cool air. ... A: If you disconnect the heating coils, you will have to remove them completely from the dryer. It all ... | |
| Sunbeam Mixmaster Heritage Series Stand Mixer | 2/8/2012 |
| Q: Machine only turns on to a super fast speed. Doesn't operate any any speed except super fast. It ... A: It sounds like the main capacitor has shorted out. You do not list a model # so I am guessing that ... | |
| Replacement Parts for Sunbeam Kettle | 2/7/2012 |
| Q: I am looking for the "ON/OFF Switch" for a Sunbeam 1.7L Kettle - Model: 3234-33. A PDF of the ... A: I checked on our Sunbeam service center web site and found that Sunbeam does not sell any internal ... | |
| electical hook up for heater/vent/fan for Bathroom | 2/7/2012 |
| Q: My husband & I have done renovation to our house before and we have changed out the ... A: I am sorry but I am not a household electrician and without being there to test the different units, ... | |
| beaters for dormeyer mixer | 2/7/2012 |
| Q: My wife recently found her mothers mixer, and it was repaired to working order, but I cannot find ... A: I may be able to help you but you will have to send us a picture of an old beater so we can try to ... | |
| Oster kitchen center vs new models | 2/4/2012 |
| Q: I bought my Oster in 1988. The number on the bottom says 968-08 F. Myis the new model which says ... A: The new mixers are not nearly as powerful as your machine and are not repairable. The speed control ... | |
| porcelier coffee pot | 1/20/2012 |
| Q: I have a porcelier coffee pot used for decoration purposes only. Lid (top on pot) has been broken. ... A: This sounds like a very nice coffee maker but that will make finding a cover for all the harder as ... | |
| wiring lamp cord to a switch | 1/20/2012 |
| Q: I have an older lamp that has a plug cord (two wires) that I want to connect a switch that has three ... A: I have not heard of a lamp with a solenoid in it. Generally a solenoid will control something ... | |
| Wiring a leg lamp (with nightlight) | 1/17/2012 |
| Q: Ok, don't laugh, I'm making a leg lamp (from A Christmas Story). Essentially it's a lamp with a ... A: I would trust a hardware store to sell you the correct switch before a large do-it center. I have ... | |
| replacement cord for fry pan | 1/16/2012 |
| Q: The cord on my old fry pan shorted out last nite. Do you know id i might be able to get a ... A: Hoover used a very special probe on their pans. The hole is in the middle of the probe. All other ... | |
| Rewiring a Hamilton Beach Shake Mixer Model #18 | 1/15/2012 |
| Q: Recently bought my wife a model 18 Hamilton Beach Shake Mixer. It seems to be in great shape except ... A: I do not think that you will find a manual for this unit as it was built in the 1940s. The best way ... | |
| Sunbeam Electric Skillet Heat Control unit | 1/9/2012 |
| Q: Where do I get a replacement for Heat Control Unit for Model #RC 33 Sunbeam Electric Skillet? A: If the heat control has a long probe sticking out of the center and two holes to accept the prongs ... | |
| Stripped gear in mixer head of Oster Regency | 1/8/2012 |
| Q: Mr. Kiefer, I have a very old Oster Regency. One of the gears that drives the beaters is stripped ... A: I think we may have the gear that you require but I am not at the shop today. Please copy this ... | |
| Sunbeam stand mixer model 2360 | 12/24/2011 |
| Q: What's the procedure for opening the motor casing to replace the circuit board-it appears to require ... A: I have attached a parts blow-up of your machine. I hope it will aid in your work. The back cap has ... | |
| blue ice maker mod 80533 | 12/21/2011 |
| Q: could you please tell me what the hot button does on the ice maker it produces ice wether pressed or ... A: For something this specific you would have to ask the manufacturer. We have never serviced one of ... | |
| montgomery wards mixer | 12/20/2011 |
| Q: i have an old wards stand mixer that needs cord replacement. It looks as though the bottom is 2 ... A: I am not familiar with a Wards mixer but if it is in two pieces it has to have screws in it ... | |
| Hamilton beach milkshake maker problem | 12/17/2011 |
| Q: I just got a Hamilton beach model 33 milkshake mixer. I can hear the motor humming when i put the ... A: I am afraid that there is no quick fix. It sounds like the motor shaft is stuck tight. The only ... | |
| Sunbeam Mixer base rubber foot | 12/11/2011 |
| Q: Only # I have for mixer is 100-86659 with service # I88. Purchased in 70's. All four rubber feet ... A: The only parts that you may find now are used parts. If you have a picture of your stand and can ... | |
| Hamilton Beach model K stand mixer | 12/8/2011 |
| Q: Do you have any idea where I can find a replacement for the screw that holds in the beaters for this ... A: Sorry but we sold our last used one about 2 years ago. You can try ebay.com. That is the only ... | |
| Sunbeam Vista Toaster, Model VAT-H | 12/7/2011 |
| Q: All of a sudden, nothing happens when I press the power button. It doesn't heat up, the bread does ... A: There could be many causes for your toaster not turning on. When you push the button on the front ... | |
| Sunbeam Mixmaster 1983 Vintage | 12/5/2011 |
| Q: My wife's sunbeam mixmaster does not run on the slowest speeds, and when turned up it seems to be a ... A: There is a small adjustment screw that adjusts the high and low speeds on the speed control. I think ... | |
| Dead compressor | 12/5/2011 |
| Q: I have a Craftsman Model 919.727110 oil-less,tank-less 3hp air compressor.I bought the thing in Apr ... A: If it is oil-less and tank-less, I would guess that there are no parts available for it. It does ... | |
| Sunbeam Vista Food Processor | 12/3/2011 |
| Q: I bought this used in the 80's and I love it. Unfortunately, the plastic bowl has a crack in it. ... A: We may have a used one but I am not at the shop today. Please inquire directly to us at: ... | |
| Sunbeam 60th Anniververy dough beaters | 11/30/2011 |
| Q: Every time I've tried to use my beaters for bread, the bread twists up into the mixer where the ... A: You should be using the special dough hooks but some machines did not come with them when new. I ... | |
| diasemble Sunbeam 1-7A | 11/29/2011 |
| Q: WIFE HAS HAD THIS MIXER FOR,I GUESS,OVER 30 YEARS. STILL RUNS GOOD BUT NOW SEEMS TO MAKE MORE NOISE ... A: To change the grease in this mixer, you will have to get the sticker off of the front of the machine ... | |
| Timer for electric heater | 11/28/2011 |
| Q: I have a small electric heater I use under my computer desk. It requires me to turn it on and off. ... A: You need a timer that will work on a large wattage appliance such as the heater. These heaters draw ... | |
| "high intensity" light bulbs versus ordinary bulbs | 11/27/2011 |
| Q: Can I use a "high intensity" 40 watt light bulb in my china cabinet, instead of the maximum type G ... A: I think you will find that most high intensity bulbs work on low voltage (12 volts) and if you plug ... | |
| Broken Keurig Coffeemaker | 11/26/2011 |
| Q: I have a Keurig B70 cup-at-a-time coffeemaker that is out of warranty (so Keurig won't do anything ... A: There is a main control board that controls all functions of the coffee maker and it has gone south. ... | |
| VINTAGE STAINLESS SUNBEAM MIX MASTER 12 SPEED #100-86659 | 11/24/2011 |
| Q: Do you know where I can get an exploded view of this appliance (to disassemble and reassemble). ... A: We have been an authorized service center for Sunbeam for over 25 years and the only thing that we ... | |
| signal fan wiring | 11/23/2011 |
| Q: Kiefer, Recently I was given an old Signal Electric attic fan and was asked to install it in a barn. ... A: The four wires coming from the motor should be one hot lead and the three different speeds. They ... | |
| Hamilton Beach Schovil model 25 beaters | 11/21/2011 |
| Q: Where can I find beaters for a Hamilton Beach Schovil model 25 stand mixer? I can find the long ... A: Please contact our shop at: info@kieferappliance.com I know we were having a problem getting them ... | |
| Dormeyer mixer/silver chief | 11/17/2011 |
| Q: My mom just passed down hers to me this was her first! purchased around 57? comes with many ... A: These units were very good units when they were made and that is why there are so many of them still ... | |
| dehumidifier -- compressor not going on | 11/15/2011 |
| Q: I have a Bionaire dehumidifier which I love. Yesterday the compressor stopped working -- the fan ... A: I would say that you are correct in saying that the compressor is bad on your unit. It is trying to ... | |
| dormeyer food-fixer 4200 | 11/15/2011 |
| Q: I have my grandmothers dormeyer 4200 and it is still in very good shape. I have the large and small ... A: I am sorry to say that your model is a very popular model and beaters for it are very rare. The only ... | |
| Vintage Hamilton Beach Mixer Parts | 10/27/2011 |
| Q: I have inherited a Hamilton Beach Stand Mixer. Cannot find a Model Number but has Canadian Patent ... A: We may have one if it is the same as a Model K. If you can take a picture of the stand and mixer ... | |
| cannot remove dough hook from farberware mixer | 10/23/2011 |
| Q: I used the dough hook on my 20 year old freeware mixer, & the dough hook suddenly will not ... A: There is usually a small wire or "C" clip that holds the beater or hook into any mixer. This must ... | |
| HB Scuvill stand mixer #25 10 speed | 10/19/2011 |
| Q: I have this model would like a owners manual were can i get one, i recently purchased at thrift ... A: There is not much in a manual but there may be some oil holes in the model 25. Some had them and ... | |
| Dormeyer mixer beaters model-SM13CH | 10/15/2011 |
| Q: I need to replace the beaters of my SM13CH stand mixer. If you hsve them or can identify them by ... A: I do not have any books for the old Dormeyer mixers but I do have a few new beaters for them. If ... | |
| 4 hp air compressor | 10/11/2011 |
| Q: How much oil is in the crank case of Sears 4 hp 240 volt air compressor model 919.177541 A: I am not familiar with Sears model #s but all pumps have some mechanism to tell how much oil is in ... | |
| beaters for Dormeyer Mixer | 10/8/2011 |
| Q: I have an older Dormeyer Mixer, Model SM-13, Cat.no.0S-13C, of which I need new beaters. This is ... A: I have some new Dormeyer beaters but they are for the not-so-common models. I do not have any parts ... | |
| faberware coffee maker | 10/7/2011 |
| Q: A faberware percolator was plugged in without any water in it. Now it will not work Suggestions? A: If it is a perc, the fuse probably is open. It is copper with a solder joint in the middle. The ... | |
| stand mixer. | 10/3/2011 |
| Q: I bought a lightweight plastic stand mixer at a garage sale with no beaters. thought I could use my ... A: This sounds like a "Made in China Special". I do not know of any company selling parts for hand ... | |
| Sunbeam mixer 1-8B 423A | 10/1/2011 |
| Q: need to replace part inside mixer that turns and where metal on underpart of bowl turntable fits ... A: The only part that turns on this model is the cap on the outside. There is a speed control on the ... | |
| Sunbeam Vista 84071 | 9/30/2011 |
| Q: Someone gave me this processor last week. It is so old the plastic handle on the "bowl" broke right ... A: It is very rare. The only thing that I may have would be a used one. Please contact our shop ... | |
| Oster Regency Kitchen Center | 9/23/2011 |
| Q: The mixer head of my wife's unit has a broken plastic gear. I think I located the particular gear ... A: The gear that you are describing it part # 27290 on our diagram on our web site. It has a gear ... | |
| Oster Regency Kitchen Center | 9/17/2011 |
| Q: The mixer head of my wife's unit has a broken plastic gear. I think I located the particular gear ... A: We may be able to help you. If you can describe the gear that you need, please contact us directly ... | |
| Everstar icemaker Model HDIM70 | 9/17/2011 |
| Q: When i press the mode button the machine starts up, with compressor everything running fine. After a ... A: I think you have hit the nail on the head. The pc board governs all of the functions of the machine ... | |
| Sunbeam Margaritaville Drink Maker | 9/14/2011 |
| Q: I have a Bahamas Margarita Model DMO500. Water got into the bottom from melting ice and damaged the ... A: According to our Sunbeam authorized service center web site, Sunbeam does not make any parts for ... | |
| garbage disposal | 9/13/2011 |
| Q: wayne i installed a insinkerator badger5 1/2hp not sure of the amps maybe 6.2 amps. it lasted ... A: All motors will spark a little as there is current flowing between the armature and the motor ... | |
| Smoke Detectors For Greenhouses | 9/12/2011 |
| Q: I operate 4 commercial greenhouses that are 30'x100'. It is required that we have 2 smoke detectors ... A: I have never had this question ask before and am not really an expert on smoke detectors but I would ... | |
| fan noise | 9/10/2011 |
| Q: We just installed a new ceiling fan made by Hampton Bay in our bedroom. It was installed by a ... A: Any electric motor will emit some noise unless it is a very expensive ball or roller bearing motor ... | |
| Repair for a Dormeyer Mixer Model 4200 | 9/7/2011 |
| Q: I own a Dormeyer Mixer Model 4200. It was the only one they made that tilted sideways (up), The ... A: If you still have a shop in your area you are lucky. We are the only shop left in a five state ... | |
| Bobby Brown Doughnut Machine | 9/5/2011 |
| Q: I am looking to purchase a Bobby Brown Doughnut Machine and I saw on your site a post by someone ... A: I did repair one of these units not too long ago and they are a very well built machine. Please go ... | |
| small food grinder. | 9/2/2011 |
| Q: I have a small food grinder, and am interested in finding its age. The info on the bottom of the ... A: The Philips Co. has produced many small appliances over the years. They are based in Europe but ... | |
| Westinghouse Roaster/Oven RO-91 | 9/1/2011 |
| Q: i lost the thermostat control knob. i an hoping you may locate one for me. A: I am not sure exactly what the Westinghouse thermostat knob looks like but it the shaft protrudes ... | |
| replacement part | 8/31/2011 |
| Q: I have an older Oster Kitchen Center and the accessory called Oster "Power Puree -N- Ricer. I broke ... A: The ricer attachment for the kitchen center is very rare. They did not sell many of them new ... | |
| Waring blender | 8/28/2011 |
| Q: I got a Waring blender from a garage sale. The model number is hard to read, but is one of the ... A: I am not real familiar with Waring but there should be four screws on the bottom. They may be the ... | |
| Electrical Problems blowing appliances | 8/25/2011 |
| Q: I have blown several appliances and three surge strips. Now the TV doesn't work. My power analyzer ... A: You need to contact your electricity provider. If voltage falls much below 100 volts you may have ... | |
| waffle maker parts | 8/22/2011 |
| Q: Wayne, I have a Kenmore waffle maker (model # 48225) that's probably 20 years old at least. The ... A: The exact replacement part will not be available. I would suggest that if just the pins are broken, ... | |
| How to oil a ceiling fan | 8/14/2011 |
| Q: I have a 42" Alaska hugger ceiling fan ,model 268649, bought sometime in the mid 80s in my ... A: I have one doing the same thing. The only way to oil these ceiling fans it to totally dismantle ... | |
| Vintage Gm Radio floor model | 8/8/2011 |
| Q: I have picked up this Vintage Radio console for a gift. I have "googled it " and can not find any ... A: Sorry but this is way out of my line of expert knowledge. There is a web site that may help you for ... | |
| CORDLESS PHONE | 8/7/2011 |
| Q: Which one of you knows about cordless phones? ANSWER: I know that there is usually no repair to ... A: It sounds to me like your charger may not be working. The whom ever replaced the battery should ... | |
| dormeyer sm 12 ch | 8/4/2011 |
| Q: I have a dormeyer sm 12 ch and am looking for the beaters. I got it with out the beater and can't ... A: I do not think that you will find any new beaters as they stopped making them over 25 years ago but ... | |
| Dead sockets in ceiling light fixture | 7/19/2011 |
| Q: I have a second-hand candelabra-style ceiling light fixture (mfg @ 2003) with five standard size ... A: The first thing to check would be the little tab in the center of the socket that touches the center ... | |
| Mixer with Clanking Beaters | 7/16/2011 |
| Q: I have owned a Farberware Premier Series FSM 350 Mixer for several years that I received as a gift. ... A: If that is the case, the gears were installed one or two teeth off at the factory. The two gears ... | |
| Mixer with Clanking Beaters | 7/16/2011 |
| Q: I have owned a Farberware Premier Series FSM 350 Mixer for several years that I received as a gift. ... A: Farberware never made their own mixer. They purchased it from a vendor and had their name stamped ... | |
| electric fry pan | 7/15/2011 |
| Q: I have electric fry pan that has no cord. The pan itself has a centre hole with two pins sticking ... A: This should not be a problem. If you will take a measurement from the center of one pin to the ... | |
| Installing Main Gear on Oster Kitchen Center 900 | 7/10/2011 |
| Q: The main gear on my Oster Kitchen Center broke in half. How do I go about installing a new main ... A: There is a tool that will help you with the "C clip". It is a snap ring removal tool but you have ... | |
| Installing Main Gear on Oster Kitchen Center 900 | 7/9/2011 |
| Q: The main gear on my Oster Kitchen Center broke in half. How do I go about installing a new main ... A: You do not say if you have a mixer head with only two holes or the one with dough hooks as well. The ... | |
| Wall Fan Speed Control | 7/7/2011 |
| Q: I have a Lasko 3-speed wall fan. The speed is controlled by a Zing Ear ZE-208S pull switch. The ... A: Interesting problem... A couple things come to mind. First, how much slower is slower?? Then ... | |
| New cord on Sunbeam CG Waffle iron | 7/4/2011 |
| Q: Are you still repairing Sunbeam CG Waffle Irons by replacing the cord? Can you give a rough ... A: If we replace the cord on any metal appliance, we always replace it with a grounded three wire cord. ... | |
| Kitchen Aid Blender | 7/2/2011 |
| Q: Black shaft that turns the blades is stripped and I need to know how to get it repaired (where) and ... A: We do sell the driver that you need but the old one is not easy to get off. We had to make a ... | |
| Wall Fan Speed Control | 7/1/2011 |
| Q: I have a Lasko 3-speed wall fan. The speed is controlled by a Zing Ear ZE-208S pull switch. The ... A: The only way to slow the motor down is to add resistance to the circuit of the motor. You would ... | |
| sunbeam mixer | 6/30/2011 |
| Q: I dropped the unit and the plastic handle broke off. The unit still works but it needs the handle. ... A: We would have to know the exact model or service # of your mixer. Please contact us at: ... | |
| Old Sunbeam Radiant Toaster | 6/27/2011 |
| Q: I'm desperate to have someone repair my old toaster. Is it possible to send it to you or deliver it ... A: Yes, we will be glad to look at your toaster. We have a lot of used parts to repair these old units ... | |
| mixer beaters dont seem to lock in mixer | 6/24/2011 |
| Q: Are the beaters suppose to lock into the mixer? It seems our beaters do not lock in and therefore ... A: You do not say what brand mixer you have but if it is a old Sunbeam, there should be some snap rings ... | |
| Dehumidifier | 6/23/2011 |
| Q: We have a Bionaire Dehumidifier that is just over two years old. We use it in our Rec. room and it ... A: My guess is that it leaked all the freon out and now it wont cool. Feel the coils in the back of ... | |
| vintage iron skillet | 6/20/2011 |
| Q: I have my mother's (who is now 90) iron skillet frying pan and lid. The skillet is deep 3 1/2" x ... A: I would guess that you are looking at a cost of between $25-50. It really depends on what is wrong ... | |
| Hamilton Beach Scovill Model 25 mixer | 6/19/2011 |
| Q: When was this mixer manufactured? I purchased a chrome Model 25 mixer that uses the one piece ... A: Most of these chrome models were made in the 1960's. I think you are looking for the turn table for ... | |
| antique toaster | 6/19/2011 |
| Q: We became the proud owner of this toaster when our friend past away. Could you provide any ... A: This is a great looking toaster. It probably dates to the early 1900's. The brand name may be ... | |
| vintage iron skillet | 6/19/2011 |
| Q: I have my mother's (who is now 90) iron skillet frying pan and lid. The skillet is deep 3 1/2" x ... A: I can not help you with the frying pan as I have no information on them but the toaster is another ... | |
| Vintage Westinghouse roaster oven | 6/18/2011 |
| Q: I just bought a vintage Westinghouse roaster oven (model RO-5411)at a yard sale. The oven is in ... A: There are lots of chat rooms that deal with antique appliances. Try Yahoo chat rooms. Ask someone ... | |
| Hamilton Beach Mixer Model G | 6/11/2011 |
| Q: I'm trying to find replacement beaters for an older Model G mixer. I ordered on line a set that was ... A: I am not sure if we still have these but you can contact us at: info@kieferappliance.com The beaters ... | |
| hotpoint percolator cat 114p11 edison electric appliance | 6/11/2011 |
| Q: This is chrome with a spigot, looks like it is in good shape. I am afraid to try it with the cloth ... A: If you are questioning the inside of the pot you can purchase a product called CLR that can be ... | |
| hotpoint percolator cat 114p11 edison electric appliance | 6/10/2011 |
| Q: This is chrome with a spigot, looks like it is in good shape. I am afraid to try it with the cloth ... A: If the cloth cord is in good condition it should be good. Be sure to place water and the stem and ... | |
| MICROWAVE | 6/8/2011 |
| Q: I have a Whirlpool microwave hood combination, model MH1170XS. We had a power surge, and it went a ... A: The main control circuit board is probably fried and will probably cost more than a new unit. ... | |
| Dehumidifiers | 6/1/2011 |
| Q: I have been searching for a fully manual dehumidifier to replace one I have with electronic controls ... A: The only way you are going to locate one of the manual units is to purchase one used as they are not ... | |
| Universal Bread Maker | 6/1/2011 |
| Q: I work for a small museum in Utah. We received a recent donation of a #4 Universal bread maker. I ... A: Very good question. I have a little historical information on the company but have not been able to ... | |
| appliance repair | 5/31/2011 |
| Q: I have a old Philips mix master KB5102 stainless steel. The date says pat 1933 PHILIPS APPLIANCES ... A: I am not familiar with a Philips brand mixer made that long ago. I would like to see a picture of ... | |
| Frigidaire 70 pint dehumidifier | 5/31/2011 |
| Q: First let me say they do not make them like they once did!! I bought a high end 70 pint Frigidaire ... A: Yes,I have strong feelings about all of the new models. They are junk. They are made so cheaply that ... | |
| Vintage Hamilton Beach Milkshake Mixer | 5/19/2011 |
| Q: We are selling a vintage Hamilton Beach Milkshake Mixer (Model 8 from 1923). It still works and has ... A: If it is the original ss cup it will be worth more than if it was a replacement cup. Most of these ... | |
| Sunbeam Mixmaster Mixer Model 01960 | 5/18/2011 |
| Q: Trying to find a replacement part (small plastic gear) for our mixer. Do you know where to go for ... A: You do not say which gear you are looking for but I will guess that it may be a beater gear. We may ... | |
| 50's LABELLE Silver Co. percolator | 5/17/2011 |
| Q: I have a working vintage round Atomic chrome style percolator from LABELLE Silver Co. INC. (CAT # ... A: I would probably have a generic cover that may fit but the original is very rare. I would have to ... | |
| Percolator | 5/15/2011 |
| Q: I am looking to replace the glass top on a Royal-Matic Hi Speed Percolator # 2095A Made by the ... A: I should have a generic glass that will fit on this unit. There is a metal nut that screws onto the ... | |
| H.B.mixer timer knob | 5/13/2011 |
| Q: I have a beautiful vintage chrome Hamilton Beach mixer. The only flaw is that it is missing the ... A: I have about 12 mixer stands that I use for parts and none of them has a knob on it. It seems like ... | |
| Sunbeam mixmaster 12 speed | 5/13/2011 |
| Q: I purchased my mixer in the late '70s or early '80s. I am attempting to take the casing off so that ... A: It sounds like maybe the lubrication is all gone from the gears in the front of the unit. Some of ... | |
| Electric roaster | 5/11/2011 |
| Q: We have a Hamilton Beach electric roaster that has stopped heating. The indicater light is lit so it ... A: These used to cost over $120 and were worth repairing but now they are made in China and only cost ... | |
| Sunbeam mixmaster 12 speed | 5/10/2011 |
| Q: I purchased my mixer in the late '70s or early '80s. I am attempting to take the casing off so that ... A: There is a screw in the center of this disc and it has to be removed. There is a decal on the front ... | |
| air compressor gen ? | 5/9/2011 |
| Q: How do you know a air pump will fit a air tank and motor for building a air compressor, what specs ... A: If you are going to paint a car you will need at least a 60 gal. or 80 gal. would be better. You ... | |
| Dormeyer Mixwell Mixer | 5/6/2011 |
| Q: I have a Mixwell Mixer from the 1950's and I am trying to find a set of beaters for it. Do I have ... A: I do have some new Dormeyer beaters but I do not have any books to tell what models that they fit. ... | |
| re new beaters | 5/5/2011 |
| Q: i have inherited my mums sunbeam mixmaster, i think dad gave it to her in the 50's. the model number ... A: The model # is a European model # and I have no references for any of these models. If you could ... | |
| Mini fridge | 5/3/2011 |
| Q: I came to work on Monday to find that my mini fridge (Frigidaire FRC25B2GB, purchased < 2yrs ago) ... A: Do not waste money in getting it repaired. It sounds like the compressor is tight and that is what ... | |
| Black and Decker Space Saver Coffee Maker | 4/30/2011 |
| Q: My 20 yr. old B & D Coffee Maker will sometimes fail to draw the water out of the reservoir...this ... A: Vinegar may not be strong enough. Most hardware stores or grocery stores carry a product called ... | |
| Sunbeam Mixmaster #2366 | 4/26/2011 |
| Q: Trigger lever on stand broke so that the stand no longer supports the mixer head (which still works ... A: We may have a used stand or even a trigger replacement but I am not going to be at work until Friday ... | |
| Antique Toaster Cord | 4/26/2011 |
| Q: I have an antique toaster made by the Malda Electric Manufacturing co. of Fostoria, OH. It says it ... A: I think that we will be able to help you but I am not going to the shop until Friday of this week. ... | |
| nutone food center 221 | 4/25/2011 |
| Q: My husband just installed a used nutone food center #221 and turned it on, at first it ran fine and ... A: I am not familiar with this particular food center but a squealing usually means that a bearing is ... | |
| Sunbeam Mixmaster 2358 | 4/22/2011 |
| Q: Looking for carbon brush and holder set (2@)for a Sunbeam Mixmaster Model 2358 Service No. 1-93BY A: I do not have access to parts information at this location but if you send an e-mail to my shop they ... | |
| water heater | 4/21/2011 |
| Q: Water heater keeps tripping the 30 amp breaker after 2 or 3 minutes. Have replaced both elements. ... A: My guess would be the old breaker. The thermostats are just switches. If you can get new breakers I ... | |
| Value of Siver Chef model 4300 | 4/17/2011 |
| Q: I would like to know what the approximate value of a Dormeyer Silver Chef Model 4300 may be? It has ... A: There are a lot of variables when you try to determine value. What does the paint look like? Does ... | |
| Hamilton Beach Mixer 25 | 4/17/2011 |
| Q: I have burned out the motor on my Hamilton Beach Mixer 25, in good condition otherwise and have used ... A: We may be able to help you but will have to see the motor. We do have used parts that we can use to ... | |
| vintage mixer part | 4/14/2011 |
| Q: During a move, I lost the screw/bolt that attaches the combined beater to the head of my 44-year old ... A: This is a very special screw as it was designed with a bevel on it to hold the beaters in place. We ... | |
| modern maid wall mouned toaster | 4/12/2011 |
| Q: were can i find anyone who knows about moderm maid wall mounded toaster kbh 100 were i can find ... A: I have repair a number of these but I only have used parts as they have not been made for years. ... | |
| Hamilton Beach mixer model C | 4/7/2011 |
| Q: My daughter bought an older house and found some small appliances, one which is a Hamilton Beach ... A: If it still runs and has all of the speeds it is still a good mixer and is very usable with a set ... | |
| Sunbeam Mixmaster Junior Model J | 4/6/2011 |
| Q: I recently acquired a Mixmaster Junior but the beaters won't stay in. Is it possible to replace the ... A: I do not think you will ever find the gears that you need to replace for this mixer as it is very ... | |
| Vitamix Super 5000 Blade Stiff Turning | 3/20/2011 |
| Q: I have the subject blender,and have a problem with the blade assembly which is quite stiff when hand ... A: I am not familiar with this particular Vitamix blade assembly but most of them have a nut that holds ... | |
| Hamilton Beach Scovill Stand mixer | 3/19/2011 |
| Q: The body of mixer gets quite warm during use. Could it need oil and if so, where would I put the ... A: If all of the speeds work and it is not getting too hot when in use, it should be just fine. Be ... | |
| Replacement Appliance Cord | 3/16/2011 |
| Q: I'm looking for a replacement appliance cord for a Manning Bowman percolator Serial # 2-30. I need ... A: I have not seen one of these cords for years. One thing you can do is to try a round pin cord. ... | |
| 1920 kitchenaid | 3/15/2011 |
| Q: I have a 1920 kitchen aid with tons of attachments. I wanted to know if it is worth anything A: The best way to find out what it is worth is to go to Ebay and see if anyone has something similar ... | |
| 1920 kitchenaid | 3/14/2011 |
| Q: I came Across kitchen aid with all The attachments. One of them was an ice cream maker part and it ... A: I guess I do not understand your question. You say that you have an ice cream maker attachment and ... | |
| Microwave door | 3/12/2011 |
| Q: The protective film on my 2nd hand microwave door is peeling off and there is a big bubble. Is it ... A: The protective coating should be on the glass and that should not make a difference. It just ... | |
| rewiring a free standing lamp | 3/9/2011 |
| Q: I have a free standing floor lamp that is wired for 120v and want to convert it to 240v. Can you ... A: I depends on where you are going to use the lamp. If you are going to keep it in the US, then you ... | |
| Oster Kitchen Center | 2/27/2011 |
| Q: My Oster Kitchen Center only runs on high speed, no matter which attachment I try to use on it; ... A: If your unit has an electronic speed control, the problem is probably in the main control circuit ... | |
| beaters | 2/25/2011 |
| Q: I need beaters for a Hamilton Beach Scovill stand mixer model #60. I have looked everywhere. These ... A: You mixer takes the beaters that are all in one unit. They have a shaft that slides into a hole in ... | |
| Vitantonio #400 Pizzelle Maid - replacement power cord | 2/24/2011 |
| Q: I bought a #400 Pizzelle Maid by Vitantonio at a yard sale, but it didn't come with a power cord. ... A: I am not familiar with the type of cord that fits this machine but if you describe what the socket ... | |
| portable phone question | 2/22/2011 |
| Q: On a portable phone (not cellphone), after a call is ended, is it best to put the phone down on its ... A: I would say that they are on the right track. Ni cad batteries use to have a memory and they always ... | |
| water softner or whole house water filter | 2/22/2011 |
| Q: we have hard water problem and just bought a house. I am thinking to get a water softener (salt) or ... A: A water softening system does not add much salt to your water system. The salt is only used to ... | |
| GE Coffee Maker (age?) | 2/21/2011 |
| Q: GE Brewstarter Electronic Coffee Maker Cat # B3-DCM50 Can you tell me what year it was made? ... A: GE usually stamped a date of manufacture on each unit that they made. It should be stamped on the ... | |
| Home Appliance Monitor | 2/20/2011 |
| Q: I am a student at Tri-County Technical College, working on a project with a partner in an ... A: I do not know if I can be help to you but I am willing to try. Most home appliances are not ... | |
| Micro oven door handle GE Advantium model # sca1000DBB 03 | 2/19/2011 |
| Q: How do I get the door apart to get to the door handle screws A: I do not have any parts books for your model so I am only guessing. Some microwave door panels are ... | |
| Meat grinder. | 2/17/2011 |
| Q: My husband grandfather gave him a meat grinder. It is a awesome meat grinder. We would like to know ... A: The Standard Computing Scale Co. made scales in the late 1800's through the early 1900's. They were ... | |
| beaters | 2/14/2011 |
| Q: I have a Sunbeam Vista Mixmaster hand beater that is very old. I got it from My Mom when she passed ... A: We have some new beaters that fit the newer model "burst of power" mixers but I do not think they ... | |
| Repair of microwave door | 2/14/2011 |
| Q: The door of my microwave is very loose and close to coming detached. A: It sounds like the hinges are loose. They should have screws to tighten them. If they are riveted, ... | |
| GE MICROWAVE MODEL JVM1339BW02 | 2/11/2011 |
| Q: DOOR IS CLOSED, HANDLE BROKE OFF, HOW TO OPEN DOOR TO REPLACE HANDLE. A: I assume that the handle on this unit is integrated with the door latch. We do not have access to ... | |
| Sunbeam Toaster 20B won't pop-up | 1/22/2011 |
| Q: The Sunbeam Toaster 20B is from my childhood and makes delicious toast it I stand there for 1.5 min. ... A: If you can not adjust the unit using the screw in the center of the center element, you may need a ... | |
| Hamilton beach coffee maker 47454 | 1/22/2011 |
| Q: This is a brewmaster, problem is that it will turn on.any suggestions, thanks A: You do not say how old the coffee maker is or if it is a drip or perc type. By the model # that you ... | |
| old dominion 660 w Model 1218 | 1/22/2011 |
| Q: Wayne, where can I find a power cord for this old waffle maker. I remember my mom making waffles in ... A: I do not know exactly what type of cord this unit has on it but if it plugs into two round pins, we ... | |
| Sunbeam cooker/fryer from the 50's | 1/15/2011 |
| Q: I have my mother's slowcooker/deep fryer which works great but plug that goes into appliance is ... A: We would have to know what type of plug is on the cord. If it is a plug that goes into two pins, we ... | |
| universal panini | 1/15/2011 |
| Q: i have a Universal panini m-e797oa that i need a power cord for.Can i purchase this through you? A: If the cord plugs into the appliance we have most of the cords. We will need the measurement from ... | |
| wafffle maker | 1/13/2011 |
| Q: I have a Heatmaster waffle maker style 307 with a date stamp of 1933. is this a collector item ... A: Heatmaster was never a brand in itself. It was made by Proctor Silex for sale at all of the Sears ... | |
| identify mixer by serial number | 1/12/2011 |
| Q: I have a Kitchenaid stand mixer serial # WP146788 model# KP50PSWW can you help me locate a spec ... A: The easiest way to get an operator manual is go to a store that sells new ones and ask if they would ... | |
| Everstar Electric fry pan | 1/10/2011 |
| Q: I have an Everstar fry pan and all it has on it are numbers 1-10, not the usual temp numbers. Do you ... A: I have never seen a company that is harder to contact. Everstar only wants to sell not answer any ... | |
| Electric Hot Pots vs. Rice Cooker vs. Electric Kettle | 1/9/2011 |
| Q: I have some questions: -Which would be the best for making soup as well as boiling water? Hot pots, ... A: I have not had any experience with this particular product but it sounds like it should cook the ... | |
| Electric Hot Pots vs. Rice Cooker vs. Electric Kettle | 1/9/2011 |
| Q: I have some questions: -Which would be the best for making soup as well as boiling water? Hot pots, ... A: Answers: 1: Hot pots will get hot enough to boil water and be open on the top to make soup if you ... | |
| Westinghouse roaster oven | 1/8/2011 |
| Q: I have a Westinghouse roaster oven #103473. The cord sparks when I plug it in, otherwise it works ... A: I think we can help you with a new cord. If the pin spacing center to center is about 1 5/8". The ... | |
| waring meat grinder | 1/7/2011 |
| Q: I accidently put my waring MG800 meat grinder thru the dishwasher and they came out with the ... A: I have not heard of this situation before. I do not think it should make any difference as some ... | |
| Kitchen Aid mixer KD2661XMC | 1/7/2011 |
| Q: When replacing the gear(3594375) is it necessary to use the Kitchen Aid grease or can I use regular ... A: It may, if you will look at the gears on the mixer when you disassemble it, you will probably see ... | |
| Kitchen Aid mixer KD2661XMC | 1/7/2011 |
| Q: When replacing the gear(3594375) is it necessary to use the Kitchen Aid grease or can I use regular ... A: Kitchen Aid grease is what probably caused the ware on the gear that you are replacing. It gets ... | |
| Spray-painting the interior of a microwave | 1/7/2011 |
| Q: Is it safe to do it? I have an older, above-the-range-hood microwave that, despite its age, still ... A: You are correct in wanting to do something with the lower area. Rust will continue to concentrate ... | |
| mixer repair winston salem | 1/6/2011 |
| Q: I have a hamilton beach mixer model40-3 scovil that my wife dropped. I can not find anyone that ... A: We service all older small appliances that we can locate parts for. We do have a number of old ... | |
| Sunbeam toaster T-20B | 1/4/2011 |
| Q: The cord on my 55 year old toaster is dangerously frayed. I would like to get it replaced. The ... A: Yes, we service these old toasters almost daily. They are the best unit that Sunbeam ever made. If ... | |
| Kitchenaid K45SS Mixer | 1/4/2011 |
| Q: My Kitchenaid K45SS mixer does not run slow. On first notch it runs medium speed, then advances ... A: The circuit board that I mentioned is located at the top of the mixer tucked in behind the black ... | |
| Dormeyer BroilWell Rotisserie | 1/2/2011 |
| Q: Motor gave out. Single speed. Not frozen up, can spin by hand and unit will hum when energized but ... A: We have worked on many small motors but I would have to see the motor to see if we could do anything ... | |
| Model 33 Mixer fuse | 1/2/2011 |
| Q: Picked up a Hamilton Beach model 33 mixer today but it is missing both fuses, and only has one of ... A: You have two different questions here. I think you are indicating that the motor brushes are ... | |
| Sunbeam Mixmaster 50th Anniversary Edition Mixer | 1/1/2011 |
| Q: I was making bread dough today and my mixer got a little hot, so I stopped using it and finished ... A: If it is the model that I think it is, it has a 90 degree "C" fuse in it. Sunbeam recommended that ... | |
| Philishave (Norelco) HS555 Shaver Problem | 1/1/2011 |
| Q: I've had this shaver for almost 20 years. When I'm using the shaver, the shaver's power will ... A: I think I can tell you exactly what your problem is. The motor brushes on these old shavers get ... | |
| Farberware Hand Mixer Beaters | 1/1/2011 |
| Q: I can't seem to find replacement beaters!! Do you know what would be compatible?? I'd hate to go ... A: All Farberware products are now made in China and there are no parts available. It is really too ... | |
| Kitchenaid K45SS Mixer | 1/1/2011 |
| Q: My Kitchenaid K45SS mixer does not run slow. On first notch it runs medium speed, then advances ... A: There is a small circuit board in the this unit that controls the speeds that may be malfunctioning. ... | |
| Dormeyer Mixer | 12/31/2010 |
| Q: I need the beaters for my mixer model # 0470382 any suggestions? A: The only place that you may find them would be Ebay and I do not see them there very often. If you ... | |
| Dormeyer stand mixer parts | 12/31/2010 |
| Q: Looking for beaters for Dormeyer stand mixer (was my mother's), model #6503. I do not have either ... A: The only place that I can recommend is Ebay and I do not see them very often there either. If you do ... | |
| Krups grinder | 12/29/2010 |
| Q: I am again asking about the Drups spice grinder. I finally had to take vice grips to get the blade ... A: Are you refurring to the cover on top of the grinder or the little cap on the top of the blade? If ... | |
| Hamilton Beach #30 | 12/28/2010 |
| Q: my Hamilton Beach Number 30 malt mixer has a bad capacitor. Do you know where I can get a new one? ... A: I checked both of my mixers again and neither has a capacitor. I think that possibly it was ... | |
| Westinghouse Waffle Iron | 12/28/2010 |
| Q: "I am trying to locate a replacement cord for a vintage (50 - 60 years old) Westinghouse Waffle ... A: If it is a detachable cord we would probably be able to help you. Please contact us at: ... | |
| dormeyer mixers | 12/27/2010 |
| Q: I just recive a dormeyer mixer model # SM6 WH1 in new condition how much is it worth. it has two ... A: Most of these units are worth what ever you can get for them. I have seen them from $25 to over ... | |
| sunbeam mixmaster 2379 | 12/27/2010 |
| Q: I was making cookies and overheated my mixer. It stopped working and I unplugged it, let it cool ... A: There is a heat sensitive fuse in this mixer and it propably opened. All you can do is replace it. ... | |
| Mickey Mouse push button phone | 12/25/2010 |
| Q: The problem we are having is that our Vintage 1976 Mickey Mouse phone receives calls and we can hear ... A: There is a telephone repair service in Madison, Wi that will repair almost any type of phone. They ... | |
| Old Oster Regency Kitchen Center | 12/23/2010 |
| Q: We recently purchased this item at an auction thinking it was an electric meat grinder we could give ... A: The Oster Kitchen Center is a very good machine. It has a mixer head on the top that the meat ... | |
| very old dormeyer beater | 12/21/2010 |
| Q: JUST RECENTLY WE HAD A DORMEYER BEATER DONATED TO, OUR STORE. I COPIED DOWN EVERYTHING ON IT AND ... A: Even the latest model of Dormeyer is over 30 years old and that would be the 4200. I would guess ... | |
| Landers coffee/tea urn | 12/19/2010 |
| Q: I have an old stainless steel urn with spout made by Universal Landers Frary & Clark. Has worked ... A: Most of these old coffee makers had a lead fuse in the bottom close to the main element. The lead ... | |
| hamilton beach model 27 | 12/19/2010 |
| Q: How do you wire this unit? Is there a wiring diagram available? A: Hamilton Beach never sent us any wiring diagrams for any appliance they ever made. We were on our ... | |
| L,F &C Insulated carafe | 12/18/2010 |
| Q: I have a model 6820, universal carafe, Filler#020. I need a replacement filler. Do you know where I ... A: I have seen a lot of their appliances but I have not seen the particular item that you have. Your ... | |
| jet stream oven | 12/17/2010 |
| Q: How do you change the belt on a american harvest model js3000tm jet stream oven? A: Sorry I can not help you on this problem. We have never worked on this product and I am not ... | |
| Krups coffee mill | 12/16/2010 |
| Q: Wayne, Thank you for taking the time to answer this. AI have a Krups coffee mill Type 408. It ... A: That should work if you can find someone to help you hold the screwdriver in place. Grip the blade ... | |
| universal percolator part | 12/16/2010 |
| Q: i have a Universal E9169(landers,frary &clark) it does not ahve the original top. i bought it off ... A: I do not think you are going to find one. Some people did loose these covers and they have not been ... | |
| Dormeyer Model 4200 Food-Fixer | 12/14/2010 |
| Q: I recently purchased a Dormeyer Model 4200 Food-Fixer. Works beautifully. I used the meat grinder ... A: I only have three Dormeyer mixers for parts and they all have the covers missing so I can not look ... | |
| mixer beaters out of alighnment | 12/13/2010 |
| Q: my wife's Sunbeam Silver Legacy stand mixer; mdl. # 2347-30 has miss-aligned beaters. Can this be ... A: Before you start to disassemble the unit, turn each beater and see if there is any play in them. ... | |
| Panasonic FF-543BFW Microwave Oven | 12/13/2010 |
| Q: Mr. Kiefer Normally, to heat a cup of tea, I enter 6o seconds and hit "Start". Light goes on, ... A: My guess would be the main control circuit board is not working properly. It has to tell the main ... | |
| farberware coffee urn | 12/12/2010 |
| Q: I have an older coffee urn (Farberware 155A) w/ the removable 2 prong cord. It works well, but the ... A: It should be but the problem could be loose terminals on the inside of the pot. Take the bottom of ... | |
| Coffee Percolator Issue | 12/11/2010 |
| Q: I have a Presto 12 cup percolator, model 02811. After the coffee brews and goes to warming mode it ... A: The part # that you list sounds like an old Presto part # but I do not know if it is the correct one ... | |
| Coffee Percolator Issue | 12/11/2010 |
| Q: I have a Presto 12 cup percolator, model 02811. After the coffee brews and goes to warming mode it ... A: You hit the problem on the head. The "rope heater" is probably not working. This heating element ... | |
| Old proctor silex 4 slice toaster | 12/10/2010 |
| Q: I have no voltage reading at the end of the power cord. There looks to be an inline resistor(or ... A: We used to work on a lot of these toasters but that was many years ago and I do not recall a ... | |
| The best blender/juicer combo | 12/10/2010 |
| Q: I'm looking for a Christmas present for my mother and I know that she's been looking for a good ... A: The Oster 3157 is a juice extractor and sells for under $50. This is not a blender and keep in mind ... | |
| AIR PURIFIER-LIVING AIR XL15: | 12/7/2010 |
| Q: Re: AIR PURIFYER-LIVING AIR XL15: It stopped working at all; no sound, no movement. I found the fuse ... A: You are correct. This is the control circuit board and something on that board is has a direct ... | |
| AIR PURIFIER-LIVING AIR XL15: | 12/7/2010 |
| Q: Re: AIR PURIFYER-LIVING AIR XL15: It stopped working at all; no sound, no movement. I found the fuse ... A: I am not familier with this brand machine. Is it an electronic air cleaner or filter type? If it ... | |
| Hamilton Beach Mixer | 12/3/2010 |
| Q: I have a Hamilton beach stand/hand mixer that has a Canadian Patent 1938, it has a model number of ... A: I think we have new beaters for this model in stock but not sure. I do not go to the shop every day ... | |
| Replace brushes on electric tool | 12/3/2010 |
| Q: I have a Sears Rotary Tool, Model 572.610530 and it is making a rattling noise with very little ... A: I think you will find that if you do get the brushes out you may not be able to find replacement ... | |
| Cuisinart 12 cup coffee pot.Mod#cbc-00bj2 | 12/2/2010 |
| Q: My coffee pot is leaking water on the counter during brewing. I took the bottom of and discovered a ... A: I do not know where you are located but we may be able to help you. If you can send us the old tube ... | |
| Dormeyer Mixer | 11/28/2010 |
| Q: I have a Dormeyer, model #4200, serial #0336240. However, I no longer have bowels that fit with the ... A: I think that we may have a pair of used Dormeyer bowls but I am not at the shop today. If you will ... | |
| Replacement resistor | 11/27/2010 |
| Q: I have a Hamilton Beach Scovill Deluxe mixer model 40-3. The best I can tell is that the resistor ... A: I think that you are correct in saying that this is a capacitor. These old HB mixers do have the ... | |
| Krups coffee mill | 11/25/2010 |
| Q: Wayne, Thank you for taking the time to answer this. AI have a Krups coffee mill Type 408. It ... A: The blade has a piece of plastic in the center that screws into the metal drive shaft. I think what ... | |
| sunbeam 11c mixer | 11/22/2010 |
| Q: If you have a parts diagram of this mixer can you please send me a copy? I recently acquired one of ... A: You are right on with the lubricants. The wheel bearing grease will adhere to the gears very well ... | |
| Universal Iron by Landers, Frary and Clark No E7886B | 11/21/2010 |
| Q: How old is this Iron? A: Most of these irons were made in the 1940-50s. I have tried to attach some information that was ... | |
| Sunbeam Mixmaster 10 | 11/21/2010 |
| Q: I am restoring my great-grandmothers Sunbeam Mixmaster Model 10. I am looking at purchasing another ... A: Yes. Most of the internal parts are the same. The main part is the speed control and on/off ... | |
| Vintage Hamilton Beach Turntable | 11/18/2010 |
| Q: I recently acquired a Hamilton Beach stand mixer, model 25. The turntable has several cracks and I'd ... A: They have not been available new for over 10 years. I do have one used white plastic turntable that ... | |
| electric percolator repair | 11/18/2010 |
| Q: I have a 1950's era Westbend electric percolator that needs to be repaired. I'm having trouble ... A: Yes, we will be glad to look at it for you. It all depends on what parts it may need. Some parts ... | |
| Westhouse Stand Mixer | 11/16/2010 |
| Q: I have a westinghouse stand mixer Catolog # FM-81 S/N3044 Style # 1379805. Would like any info ... A: I think this is the one that has the speed control around the handle on the top. The company is now ... | |
| Kitchenaid K45SS mixer | 11/15/2010 |
| Q: I took apart, re-greased, and reassembled my mixer. Now the motor won't start. I didn't do ... A: The first place to start is the motor brushes. If they were removed, my quess is that you did not ... | |
| Sunbeam Vista Mixmaster 1-8B | 11/14/2010 |
| Q: ecently, I found a Sunbeam Vista Mixmaster model no. 1-8B. It had everything it came with when it ... A: They did make dough hooks for this model but they were sold as a accessory so there were not many ... | |
| Black and Decker electric mixer replacement bowl | 11/14/2010 |
| Q: I have a Black and Decker electric stand mixer - model number SM-100, type 1. It came with a large ... A: I think that you will only find one maybe on Ebay. You have an older mixer and they take a special ... | |
| Kenmore Elite Microwave | 11/13/2010 |
| Q: acting weird. Display won't keep time, and kind of wavers - it's not solid. It also seems slow ... A: There is a control circuit board in every micro wave that controls all of the functions of the unit ... | |
| Dormeyer Electric Coffee Maker | 11/12/2010 |
| Q: My father has a Dormeyer Electric Coffee Maker Model number 6901. It is missing the glass insert ... A: Dormeyer has been out of business for over 25 years so I do not think you will find one. You may ... | |
| Sunbeam 60th Ann. Stand Mixer | 11/12/2010 |
| Q: I was making pretzels yesterday and realized a little too late that I had the wrong attachments on ... A: I think the 60th ann. mixer has an electronic speed control in it and you may have fried it. There ... | |
| 1950's vintage Hamilton Beach Model H Stand Mixer | 11/10/2010 |
| Q: The speed control on this mixer is inop. Is there a replacement for it or could the single speed ... A: If the speed that it now runs is high, I do not think that the problem is the speed control. It ... | |
| 110V Hair dryer blew on 240V circuit | 11/10/2010 |
| Q: Brookstone Ionic 1875 Dual Voltage hair dryer Model YL-358. Set on 110V plugged into 240V. Am sure ... A: I do not know of any brand hair dryer that you can get any information on concerning repair. Almost ... | |
| farberware coffee pot | 11/8/2010 |
| Q: model 155B serial 1132819 this is a 55 cup coffee pot it quites perking a third of the way through. ... A: The first thing to try would be a new thermostat. It sounds like it is getting weak and turning off ... | |
| arnold soda mixer #15 | 11/8/2010 |
| Q: how do i remove the motor and shaft from the housing. im trying to refurbish the unit. A: We do not see many of the Arnold units, most are Hamilton Beach. I think that the shaft that does ... | |
| Rangaire Shelf Hood Circuit Board Replacement | 11/8/2010 |
| Q: I need the printed circuit board assembly for a Rangaire Model HS202 Shelf Hood, S/N 0887-1-24972. ... A: Every company has their own control circuit boards developed for their products. The only ... | |
| 12 cup electric coffee maker missing part | 11/7/2010 |
| Q: I believe it was purchased in 1957 , but found that the stem insert and coffee holder are missing. ... A: Every brand has a different stem and basket. There is even a difference between some models of the ... | |
| kitchen center 5550-61A | 11/7/2010 |
| Q: The mixer driver gear split and the above connecting gear is gouged. Do you have a replacement part ... A: I may have access to these parts soon if you are interested. I will have to purchase the entire ... | |
| SUNBEAM VISTA RADIANT SHADE CONTROL TOASTER | 11/7/2010 |
| Q: THE MODEL IS VAT - H A SMPLE SIZE TUBE OF CREAM EVIDENTLY FELL INTO TOASTER PER SON - I DID SEE ... A: Sorry, they are no longer made. If you would like us to look at it and diagnose any problems that ... | |
| ceramic heater | 11/6/2010 |
| Q: We have a small ceramic heater by comfort zone. I have it plugged into a gfi outlet. After using ... A: No. There is probably a problem with the plug. On molded plugs sometimes the wires break inside ... | |
| power cord for LA Belle coffee percolator | 11/5/2010 |
| Q: I just purchased a LA Belle Silver coffee percolator from a local thrift shop and the cord is ... A: I am not real familiar with this brand but if you will describe the cord, we may be able to help ... | |
| sylvania toaster oven | 11/2/2010 |
| Q: I bought an sylvania toaster oven a few months ago from a homehardware and it was the biggest ... A: I have not heard of this brand but I will give it a try. It sounds like maybe the temperature ... | |
| Rangeaire vent hoods | 11/1/2010 |
| Q: I can't see the model number on my ventilation hood above my range to order a replacement light and ... A: You do not really have much to go on. I would take the old light and filter with you and stop at a ... | |
| power cord needed | 10/31/2010 |
| Q: I have an old Clairol Kindness 24 Instant Hairsetter with mirror. I found the set but I can't find ... A: We have a cord that has 5/16" center to center. I do not know if that will work or not with out ... | |
| KitchenAid k45ss | 10/27/2010 |
| Q: this was working fine, until I unscrewed the black plastic screws on either side of the main body ... A: The black plastic screws are the brush holders. You probably removed at least one of the brushes as ... | |
| everstar HDIM35 icemaker | 10/27/2010 |
| Q: The icemaker will make the ice, however it will not release it from the tray. Any suggestions??? A: We do not work on these appliances so I have no experience in repairing them but I will give you one ... | |
| Toastmaster 1B24 Toaster | 10/27/2010 |
| Q: I have a Toastmaster 1B24 Toaster that looks like it is missing part of the temperature control. I ... A: I checked my old toasters and do not have one like yours. I have a few older models but they are ... | |
| Dormeyer Model SM13CH | 10/26/2010 |
| Q: Do you have beaters for a Dormeyer Model SM13 CH? If so, how much would they cost? A: I do not have any books on Dormeyer but if you would send us a picture of the beater ends that go ... | |
| identifying dormeyer mixwell attachments | 10/25/2010 |
| Q: i recently bought a dormeyer mixwell sm6 wh1 with attachments. i see from this site that i am very ... A: I think the long plastic tube may be a part for a sausage stuffer attachment but you do not have any ... | |
| Hamilton Beach Scovill model 40-2 mixer | 10/24/2010 |
| Q: I need beaters for a Hamilton Beach Scovill model 40-2 stand mixer. I've searched all over the ... A: I am not sure what the beaters look like for a 40-2 mixer. If they are attached together with a bar ... | |
| Dormeyer 4201 | 10/23/2010 |
| Q: Trying to overhaul a 4201 serial 0062134 for my daughter-in-law (it was her Grandmothers), but I ... A: I checked my old parts mixers and did not have what you need. You may have to buy a parts mixer on ... | |
| Sunbeam Model 20-3 AG Temperature Adjustment | 10/23/2010 |
| Q: I have the above toaster which toasts too dark even with the temperature lever at the lightest ... A: Yes, there is a hex screw on the end of the toaster. Turn it about 1/4 of a turn at a time ... | |
| sharp carousel microwave oven | 10/23/2010 |
| Q: I have a sharp carousel microwave oven model R-530EW. The screen is no longer readable. I by mistake ... A: You have done all of the easy things to get it back in operation that I would have suggested. Did ... | |
| Sunbeam Mixer missing screw & nut | 10/22/2010 |
| Q: I have a Sunbeam Mixmaster Mixer, Model #2366, date stamp of P203K. The turntable doesn't work, and ... A: The original screw had a square head, I think, but a flat head or hex head should work if they are ... | |
| Sunbeam Mixer missing screw & nut | 10/22/2010 |
| Q: I have a Sunbeam Mixmaster Mixer, Model #2366, date stamp of P203K. The turntable doesn't work, and ... A: I am not sure of the size of the screw but if you take the mixer head into a hardware store they ... | |
| Oster coffee maker model 3309-33 | 10/21/2010 |
| Q: I love my coffee maker but unfortunately the glass pot leaks terribly. I would like to buy a ... A: Unfortunatally Oster does not make any parts for their coffee makers that are this old. If you were ... | |
| Krups toaster oven | 10/20/2010 |
| Q: This toaster over overheats when I toast and when I bake certain things. The time space blanks out ... A: It sounds like it needs a new control board but without testing the unit I am only guessing. I ... | |
| Microwave oven | 10/19/2010 |
| Q: Why would my microwave oven all of the sudden start coming on by its self ?? We leave it unplugged ... A: There is a main circuit board that controls the whole machine and it sounds like it is defective. ... | |
| how can I get new beaters?2 | 10/19/2010 |
| Q: last night while staring in my mixing bowl, I hit the beaters with a wooden spoon, will need I say ... A: I do not think you will find new ones as they have not been made for over 15 years. You could try ... | |
| dormeyer stand mixer | 10/15/2010 |
| Q: I came accross my mothers old Dormeyer stand mixer. It has several attachments & i have no idea how ... A: We do not have any books on Dormeyer any more as they stopped production over 25 years ago. They ... | |
| sunbeam mixmaster # 9 | 10/15/2010 |
| Q: I have inherited a sunbeam mixmaster model 9. It has no beaters. Also, there are 2 holes under where ... A: The two holes are for the turntable. It supports the two different size bowls. One hole is for the ... | |
| Rotary Phone - need to remove finger dial and finger stop | 10/12/2010 |
| Q: I have just purchased a rotary phone from ebay. Unfortunately the finger dial was misaligned, I ... A: We have never worked on these phones but a friend of mine used to work for ATT and may be able to ... | |
| Sunbeam Vista Mixmaster gears | 10/11/2010 |
| Q: I'm looking for a pair of the plastic beater drive gears and a set of beaters. A: Sunbeam called at least 6 models "Vista" over the years. There should be a Service # located where ... | |
| REPAIR | 10/10/2010 |
| Q: WOULD LIKE TO KNOW WHERE I COULD GET A DORMEYER SILVER-CHEF 4300 MOTER REBUILT A: You are probably not going to find anyone that has any parts for this mixer to rebuild it. I would ... | |
| Looking for a manual for Sunbeam Mix Master Model #01960 | 10/10/2010 |
| Q: I would like a manual for a like new Sunbeam Mixmaster Model #01960, do you know where I could get ... A: Sorry, we do not have any. You may be able to get one on ebay. Sunbeam only goes back to 1998 on ... | |
| scuvill hamilton beach mixer model 25 | 10/10/2010 |
| Q: my mixer runs fine except i smell something funny after it has to beat something heavy like mashed ... A: We can repair your mixers unless they require parts that we do not have. There are no new parts ... | |
| Sunbeam mixer model 2360 | 10/2/2010 |
| Q: can you give us a diagram or some idea on how to disassemble our mixer, it just stopped working. A: I have attached a copy of what I have on the 2360 but I have to tell you there are no new parts ... | |
| Dirt Devil | 10/1/2010 |
| Q: I have a Dirt Devil hand-held vacuum, about 2 years old. It runs fine but it only runs for about 30 ... A: First, check to see if the charger is good. If you plug it in for 15 min. and the charging ... | |
| Sears Dehumidifier 580-52450200 | 9/30/2010 |
| Q: My Dad passed away and I took his dehumidifier for my basement. However, it doesn't seem to ever ... A: There is a humidistat in the unit that regulates the humidity in the air. This unit should be ... | |
| mixmaster repair | 9/30/2010 |
| Q: I have a sunbeam mixmaster model 11c that started to run constantly at high speed as long as it is ... A: Yes. This is actually what we do. If sounds like you may have a capacitor that has shorted out or ... | |
| Dormeyer 4201 Mixer | 9/26/2010 |
| Q: This mixer needs a new electric cord and I am having a problem opening it up. Any suggestions? A: I have a 4200 and am going to assume that it is the same. Take the screw out of the handle and ... | |
| Sunbeam mix master | 9/25/2010 |
| Q: Can an old mixmaster be cleaned up cosmetically? A: Yes. We usually use a good glass cleaner on all of our repaired mixers before sending them out. If ... | |
| old hamilton beach meat grinder | 9/23/2010 |
| Q: I have a circa 1950's hamilton beach meat grinder. Some of the parts are missing. How do I ... A: The wood stick is called a "pusher". I am not really sure that they made very many different discs. ... | |
| Unicersal Coffeematic | 9/21/2010 |
| Q: am trying to replace the stem, basket and cover for a Universal coffeematic, electric coffee pot - ... A: Sorry but we have been out of Universal parts for over 15 years. The only place you may find them ... | |
| iron malfunction | 9/21/2010 |
| Q: My Rowenta 1800W Advancer iron won't heat up. A: Usually what happens is that the thermostat on the sole plate will stop operating. This is a weak ... | |
| Harvest Maid FD5000 dehydrator | 9/20/2010 |
| Q: I have a Harvest maid FD5000 dehydrator fan works but I believe the heating element is not, it won't ... A: I have had absolutly no luck finding internal parts for anything made by Harvest Maid. They are ... | |
| Vintage Hamilton Beach-Scovill Mixer Model 25 | 9/20/2010 |
| Q: I recently purchased this beautiful mixer and am looking for additional mixer attachments, ... A: I have not seen a dough hook for these old units but that doesn't mean that they were never made. ... | |
| Wiring diagram for Cuisinart Vertical Rotisserie | 9/20/2010 |
| Q: My dog chewed the cord off my CVR 1000, and unfortuniately pulled the connections off inside the ... A: Cuisinart does not have such things as all of their products come from China and they do not want ... | |
| Universal pec pot | 9/18/2010 |
| Q: I have a Universal per. pot and need a cord for it. The info in the bottome is Pat No. 1905111 ... A: If the prongs on the pot are round, I think we can help you. Universal did make a flat prong unit ... | |
| replacement power cord | 9/18/2010 |
| Q: I have a Breadman Pizza Oven that needs a Cat. No. PL-30 Plug. Is this available? A: I am sorry but I do not have any parts books for Breadman products and therefore do not know what ... | |
| microwave cooking times, different wattages | 9/14/2010 |
| Q: This is intended as a follow-up to the answer supplied at ... A: I agree with you. Using my experience with microwaves, this does not happen. You may cut the time ... | |
| i need to find a owner manual | 9/13/2010 |
| Q: where can i find an owner manual for a modern maid electric wall stove model # DC045002 serial # ... A: Modern maid made a lot of built-ins for houses in the 50s and 60s. They are presently out of ... | |
| emerson fan | 9/8/2010 |
| Q: I cannot figure out how to remove the blades fro my 1923 model 71666 emerson fan.It has 6 brass ... A: I am not familiar with this particular fan but there are only a few ways that blades are usually ... | |
| Hand Mixer - Who Made | 9/7/2010 |
| Q: I have a Grant Maid Mdl R-6A. On the bottom of mixer I have the following: WTG 89938-W, WTG 89946-V, ... A: If you could send me a picture I may be able to identify it. Sunbeam, Hamilton Beach and Dormeyer ... | |
| Nesco 6qt roaster | 9/3/2010 |
| Q: I have a older 6 qt Nesco roaster and the temperature knob has been lost in a move, any idea where I ... A: If the shaft of the thermostat protrudes outside of the case at least 1/2" we may be able to help ... | |
| Oster Kitchen Center Bowls | 9/1/2010 |
| Q: I have some old bowls and other accessories (meat grinder, juicer, food processor) that were used on ... A: Yes, almost all accessories can be used on any Kitchen Center. The only thing is to make sure there ... | |
| KitchenAid K5SS @ 1984 | 9/1/2010 |
| Q: The speed control is not working properly on my mixer. The slow speed is fast and there is hardly a ... A: You have done your research well. The problem could be in the phase control but without testing it ... | |
| Cord replacement 50's milkshake mixer | 8/28/2010 |
| Q: I would like to replace the cord on a vintage 50's Hamilton Beach 3 head milkshake mixer or machine. ... A: Yes, you should use a three prong grounded cord as the case is all metal. If you can take the ... | |
| Microwave | 8/27/2010 |
| Q: Wayne, here's a challenge for you: We scratched the inside of our brand-new microwave. It has a ... A: You should be able to get some appliance paint from a large appliance dealer to paint over the ... | |
| sewing machine | 8/26/2010 |
| Q: I have a sewing machine which operates on 240 volts for which I use a step-down/up transformer to ... A: No. You will have to wire the socket directly into a 120 volt source which is before the ... | |
| Beaters for vintage HB hand mixer | 8/25/2010 |
| Q: I have a 1956 vintage Hamilton Beach Mixette hand mixer that the beaters won't stay in anymore. It ... A: These springs were the weak point of these beaters. You may also want to check the gears in the ... | |
| antique waffle iron | 8/25/2010 |
| Q: I am looking for picture and value of old westinghouse round waffle iron with cloth cord, wooden ... A: I do not have such an appliance on hand right now but we do get them in for service now and then. I ... | |
| sewing machine | 8/25/2010 |
| Q: I have a sewing machine which operates on 240 volts for which I use a step-down/up transformer to ... A: Try a travel shop in New York. They may carry items for use in Europe. Or you may try to wire the ... | |
| Sunbeam Vista from 1984 | 8/24/2010 |
| Q: I just received a Sunbeam Vista Food Processor from 1984 I believe I know it was the 1980's. It ... A: I am not familiar with the term "food conveyor". Are you referring to the bowl? If you can give ... | |
| Replacement for Uniprobe JPR 1104 controller | 8/23/2010 |
| Q: Previously you described an alternate controller for the Uniprobe JPR 1104 that required ... A: If you are refering to a Mirro fry pan modification, yes it can be done. You have to drill a hole ... | |
| Cuisinart Coffee Maker Shuts Off | 8/19/2010 |
| Q: I'm hoping you can help me. Recently, my Cuisinart grind and brew coffee maker shuts off around 3-6 ... A: The thermostat is heating up to the specified temp. and then turning off. This could be because of ... | |
| Oster Skillet | 8/15/2010 |
| Q: I have an Oster skillet, Model 3001 (which see is an older model.) During transit in our RV, the ... A: Sorry I do not think I will be much help in this matter. Sunbeam does not have any drawings of ... | |
| percolator fuse | 8/11/2010 |
| Q: I have a LaBelle percolator (old) with a blown thermal fuse and am looking for a replacement, any ... A: We have a couple of different fuses that may work but I would like to see the fuse. Can you take a ... | |
| Sunbeam Mixmaster 2379 | 8/10/2010 |
| Q: one of the holders for the beaters will no longer engage. Is this, clip, spring, collar, snap ... A: I am sorry but Sunbeam does not make any internal parts for your mixer. Almost all of their ... | |
| sunbeam mixmaster | 7/27/2010 |
| Q: I have a sunbeam mixmaster which Ipurchased a few yrs. back. The blades do not rotate any more. ... A: If it is over 15 years old I may be able to help you. Check the label on the machine and see what ... | |
| Rowenta Clothes Steamer | 7/27/2010 |
| Q: The small stem broke off of my Rowenta clothers steamer and now all the water in the resevior runs ... A: You do not say if it is a portable or floor model. The portable units do not have any parts ... | |
| electric blanket cable shortening | 7/25/2010 |
| Q: this is a sunbeam. it has 2 controllers and the inside is accessible. there are 3 wire cables ... A: Sorry. Yes, 1/2 " is correct. The heat shrink is only an insulator as the wires should be soldered ... | |
| Oster Sunbeam Cordless Kettle Model 5964-33 | 7/22/2010 |
| Q: The illuminated On/Off Button does not light up to heat the water when I plug in the kettle. The ... A: That button is connected to a reset thermostat and when it no longer functions you may as well toss ... | |
| repair of sunbeam mixmaster | 7/20/2010 |
| Q: Purchased a Sunbeam Stand Mixmaster in 2008 (it was from 2004 and is now out of Warranty) I never ... A: Probably what has happened is that the plastic gears are stripped in the head. This would cause the ... | |
| spare part for microwave | 7/20/2010 |
| Q: We have lost the small toggle that fits into a keyway under the glass plate in some microwaves to ... A: I am guessing that by "toggle" you are talking about the driver for the glass plate. The glass will ... | |
| power cord | 7/20/2010 |
| Q: I am in need of a power cord for a Sunbeam Crocker Cooker-Fryer. My old plug had moisture overflow ... A: I think we have what you need. Please measure the distance from center to center on the pins of the ... | |
| beaters | 7/19/2010 |
| Q: I am looking for Dormeyer beaters for a Silver Chef. I have the grinder attachment but no beaters. A: Dormeyer beaters are very difficult to find. I do not have any books any more for Dormeyer so model ... | |
| microwave | 7/16/2010 |
| Q: why dosen't the microwave heat food A: There could be many reasons. The mag tube may be burned out, the circuit board may be burned out, ... | |
| Electric Coffee Percolator | 7/12/2010 |
| Q: I turned on a friend's GE electric coffee percolator without water in the pot and I think I fried ... A: It probably has a fuse that overheated and opened. We would have to see the unit to see if we could ... | |
| old microwave | 7/7/2010 |
| Q: i dont know if you can help me ... i have a simplicity microwave that was manufactured in 1978 ... i ... A: Over the years the magnet in the magnatron tube can loose its power and therefore it will take ... | |
| Sunbeam Mixmaster | 7/7/2010 |
| Q: The button for tilt release on my new Heritage Sunbeam mixmaster will not work. Only used this ... A: I would call Sunbeam customer service and tell them your story. If they will cover the unit under ... | |
| Ceiling fan | 7/7/2010 |
| Q: What is the best direction to run a ceiling fan in the summer? A: Since heat rises, most of the fan companies say that you should drive the hot air from the ceiling ... | |
| Sunbeam Mixmaster | 7/6/2010 |
| Q: The button for tilt release on my new Heritage Sunbeam mixmaster will not work. Only used this ... A: It sounds like it is out of warranty. It is not much good the way it is so, if I were you, I would ... | |
| microwave light, how do you change? | 7/6/2010 |
| Q: have a panasonic model # NN E666BA don't know how to get to bulb to change it. can you help? thank ... A: I do not have any microwave books but I can quess. All bulbs are either screw in or have a special ... | |
| Sunbeam Mixmaster | 7/5/2010 |
| Q: The button for tilt release on my new Heritage Sunbeam mixmaster will not work. Only used this ... A: After looking at a parts diagram of your mixer, I see that there are no parts available for this ... | |
| Sunbeam Mixmaster | 7/4/2010 |
| Q: The button for tilt release on my new Heritage Sunbeam mixmaster will not work. Only used this ... A: Sunbeam made a Heritage mixer at least three times in the last 40 years so it is hard for me to say ... | |
| Black & Decker Spacemaker Coffee Maker | 7/3/2010 |
| Q: My Black & Decker Spacemaker Coffee Maker was working fine then it just lost all power - heat, ... A: It sounds like you have blown an internal fuse or maybe a thermostat. If you can find the fuse, we ... | |
| 1935 G.E. hotpoint mixer repair | 7/2/2010 |
| Q: i have the above item and i am wondering if you may have any suggestions on how to repair it. the ... A: If you had a Hamilton Beach or Sunbeam mixer of that vintage I may be able to help you but there ... | |
| Dormeyer mixer and stand | 7/1/2010 |
| Q: I wish to find out about how much my Dormeyer mixer, stand, and 2 beaters is worth. It is off white ... A: The best way to get a value for any small appliance is to go to Ebay.com and see if you can find ... | |
| Re: Coffee Pot Fuse Wheel | 7/1/2010 |
| Q: I recently purchased an old Farberware coffee percolator. The model No. is 206. The pot makes ... A: The problem is not the fuse but the thermostat. This is an old coffee maker so I am not sure what ... | |
| Former repair | 7/1/2010 |
| Q: Wayne: I sent you a Hamilton Beach #18 mixer, approx. 2-3 years ago. You installed a new cord, and ... A: Is this #18 a food mixer or a drink mixer. It sounds like it may be a drink mixer. If it is a ... | |
| insink-Erator | 6/30/2010 |
| Q: I have an insink-Erator installed in my apartment. The number on it is 405700, 1/3 hp disposal. It ... A: You should be able to put just about anything in the unit if it were working properly. Egg shells ... | |
| Microwave interior light is out | 6/29/2010 |
| Q: I have owned a Cuisinart Microwave CMW-100 for about 2.5 years now. It has been fine until today ... A: I am not familiar with this brand as Cuisinart just stamps their name on a lot of products. It was ... | |
| Probe/Hoover Stainless Steel Fry Pan | 6/26/2010 |
| Q: My question is about the UniProbe for Model B3009 Hoover Stainless Steel Fry Pan. All of the ... A: These probes are very rare and I do not have one even as a reference. Hoover books and parts ... | |
| HAND/STAND MIXER | 6/20/2010 |
| Q: My wife got an old Montgomery Ward hand/stand mixer from her mother.The beaters she gave us don't ... A: I am sorry to tell you that you have a Dormeyer. That is not a bad thing because they are very good ... | |
| dish washer repair | 6/20/2010 |
| Q: whirlpool quite plus model #DU8920XX-0. will not work properly, appears to be a timer problem, will ... A: We do not service any large appliances but it sounds like you are on the right trail. We only ... | |
| mix master repair | 6/18/2010 |
| Q: Hey Wayne, i have a sunbeam mixmaster mod 7B it needs a cord and some brushes and a overall cleaning ... A: Yes, we would be glad to take care of your mixer. Please ship it to us with a $10 deposit to: ... | |
| dehumidifiers | 6/15/2010 |
| Q: what takes the most moisture out of the air. Low setting of 35 or high setting of 70? thanks A: I do not know what to reference the 35 or the 70 setting against. If it is % humidity, the 35 will ... | |
| hot power cord | 6/14/2010 |
| Q: I have had a Cuisinart Griddler for about three years and over the last few months have noticed that ... A: Cords get hot because there is not enough wire to carry the amperage that is required by the ... | |
| Kitchenaid Mixer Rebuild K4B | 6/13/2010 |
| Q: I am rebuilding a Kitchenaid K4B mixer. I am in the process of reassembling the gearbox. When I ... A: It depends on the viscosity of the grease that you are using. If it is a thick oil, I would fill ... | |
| Bathroom scale | 6/8/2010 |
| Q: One of my sons has bought a bathroom scale (model EB9671-31P). He did nor use or check it for a long ... A: I really do not know how to help you with out doing some testing of the unit. All I can tell you is ... | |
| window fan | 6/8/2010 |
| Q: I have a double window fan that the speed control switch is broken. the company doesn't exist . can ... A: Yes. All you need is a fan speed control that is sold at a lot of building supply stores. There ... | |
| Triangle donut mold. | 6/7/2010 |
| Q: I have a triangle donut mold that makes donuts like the brown bobby. But it is round and looks like ... A: I have been in the small appliance business for over 25 and am sorry to say that I have not seen ... | |
| Bathroom scale | 6/7/2010 |
| Q: One of my sons has bought a bathroom scale (model EB9671-31P). He did nor use or check it for a long ... A: I think you may be correct. There has to be contact points that move when someone steps on the main ... | |
| Sunbeam Mixmaster repair | 6/4/2010 |
| Q: I have a model 10 Sunbeam Mixmaster that is feeling its age. The motor works but doesn't have the ... A: It sounds like it just requires a little cleaning and lubrication. The speeds can also be adjusted ... | |
| blade and oven | 6/1/2010 |
| Q: Do you know where I can find a replacement cutting blade for the Robeson mini chopper? Also, I have ... A: Robeson has not made appliances for many years and I am not sure if they ever made any parts for any ... | |
| lights | 5/31/2010 |
| Q: Three years ago I bought three florescent lights from walmart. They are the four foot florescent ... A: Almost everything that Walmart sells is made in China and it is usually poor quality when it comes ... | |
| Kenmore Dehumidifier #580.52450200 | 5/27/2010 |
| Q: Its has work fine for 5 years and now the past year it will not turn on. I will get no power to the ... A: I would start with a new plug on the cord. This is usually the problem when moving the cord turns ... | |
| Rival warming tray cord | 5/25/2010 |
| Q: I have a Hot Serve Warming Tray Model 606 and it is missing the electric cord. Can you suggest any ... A: This probably takes a standard cord but we would have to know the distance between center points of ... | |
| Harbor Breeze Ceiling Fan: Light Stopped Working | 5/25/2010 |
| Q: The light in my daughter's ceiling fan stopped working over the weekend. We tried replacing the bulb ... A: I have no idea why companies have to have a remote on everything that they make. Any time that you ... | |
| brushes for mixer | 5/25/2010 |
| Q: I just got a Dormeyer Model 4200 Food-Fixer stand mixer. It needs carbon brushes which are 7/32" ... A: I have only two left and have not found another source for them. They are 1/32 X 1/2. To order ... | |
| Everstar Blender Replacement Parts | 5/25/2010 |
| Q: I have an Everstar Blender and after only a few times using it the base got a crack in it. Do you ... A: I have had a question like this many times over the years and I have yet to find anyone that could ... | |
| Replacement Beaters for Sunbeam 2486 Beater | 5/24/2010 |
| Q: I have used the handheld beater for MANY years and is has served me well. However, during a move a ... A: If they are made by Sunbeam they were more than likely made in China as almost all of their products ... | |
| Antique Emerson Fan | 5/18/2010 |
| Q: I have an antique Emerson electric fan. It has been restored and runs great on all three speeds. ... A: You can use a rheostat that mounds in the switch on your wall. These are available through any ... | |
| cuisinart one cup coffee maker | 5/16/2010 |
| Q: We received a cuisinart coffee maker as a gift for Christmas which we have used for several ... A: It probably has a clock and timer in it. This requires a control circuit board. Most of the time ... | |
| Hamilton Beach stand mixer | 5/15/2010 |
| Q: I recently purchased an old Hamilton Beach stand mixer, model 23. Can you tell me when this model ... A: I do not have any books on the old Hamilton Beach units but there may be a date code stamped on the ... | |
| Leaky Garbage Disposal | 5/14/2010 |
| Q: My garbage disposal has developed a leak. It is a small leak coming out of the bottom of disposal. ... A: If the leak is coming from the unit itself and not a hose leaking, it is time to replace the unit as ... | |
| Sunbeam Mixer Model MMA | 5/12/2010 |
| Q: I have just finished cleaning and gresing my wife's Sunbeam MMA. Now when I turn it on, it has one ... A: The gears are pressed onto the shaft and should not be removed. They may or may not slip after ... | |
| Farberware 8 cup percolator | 5/12/2010 |
| Q: I have a Farberware 8 cup percolator. (Also a 4 & 12 but use the 8 cup daily). It's about 6 months ... A: Try it in a non GFI outlet and see what happens. If it pops a breaker, you have a problem in the ... | |
| Obsolete percolator power cord. | 5/10/2010 |
| Q: I have an obsolete percolator made by Denby pottery with a Russell Hobbs electric base. ... A: I know exactly what you are looking for but sorry to say, they have not been available for over 10 ... | |
| West Bent buffet server model 89000 | 5/6/2010 |
| Q: I just received this buffet server and not sure how it works all the pieces are there.But does it ... A: These units were not made by the West Bend Co. but were purchased from China and sold under the West ... | |
| Sunbeam Mixer Model MMA | 5/4/2010 |
| Q: I have just finished cleaning and gresing my wife's Sunbeam MMA. Now when I turn it on, it has one ... A: When a mixer runs at full speed only it usually is one of two things. The capacitor is shorted out ... | |
| O-T-R microwave steam issues | 5/3/2010 |
| Q: Is there a piece I can install on the bottom of my OTR microwave that will help keep the front of ... A: I am not familiar with O-T-R brand microwaves but I would think that it would be the same problem ... | |
| porcelier electric coffee urn with spigot | 5/2/2010 |
| Q: I recently purchase this item at a sale. It has matching creamer and sugar. Original cord is in ... A: You should be able to get a close estimate if you check on Ebay for a like item. See what it sells ... | |
| Sunbeam Chrome MixMaster Stand Mixer | 5/2/2010 |
| Q: I just bought a vintage Chrome MixMaster Stand Mixer Catalog # 1-150 and Svc.# 1-15H. Where can I ... A: Sunbeam has a web site but I do not know if you can down load service manuals for older units. If ... | |
| hamilton beach replacement parts | 5/1/2010 |
| Q: I have a Hamilton Beach Countertop Oven with Convection and Rotisserie MODEL: 31197R, I lost one of ... A: I do not think that you will find what you are looking for. The old American Hamilton Beach Company ... | |
| Air compressor | 4/29/2010 |
| Q: I have recently acquired a 2 HP Dual Cylinder air compressor. I cannot find the make and model of ... A: You need a line pressure regulator valve with gauge. These are generic to all compressors. The ... | |
| porcelier waffle maker and grill | 4/27/2010 |
| Q: I have had for many years an antique electric porcelier waffle maker and grill with matching cream ... A: Most people that I have talked to about cleaning a grill recommend not to do so. It seems like ... | |
| GE Spacemaker microwave rattles when not in use | 4/27/2010 |
| Q: Our GE Spacemaker microwave, made in April 2000, makes a faint rattling noise from somewhere in the ... A: The only thing that I can quess that would cause the rattle would be if a door switch was not ... | |
| antique waffle iron | 4/27/2010 |
| Q: Found a white iron and enamel large 2ftx2ft table top double waffle maker in the attic with original ... A: A good way to tell is go to Ebay.com and see if anyone is trying to see something like it. If it ... | |
| Is it antique and who do I contact to sell it? | 4/27/2010 |
| Q: My dad has a Universal, Lander Frary %26 Clark, New Britian, Conn Perk coffee maker. It stands on ... A: I do not have any books on Universal any more but they were bought out by GE who was in turn bought ... | |
| Sunbeam Mixer Model MMA | 4/25/2010 |
| Q: I am in the process of cleaning the gearbox of this model MMA that has been sitting idle for many ... A: Yes, but it is not necessary. You should be able to use a good degreaser and a small brush to clean ... | |
| Air compressor | 4/25/2010 |
| Q: I have recently acquired a 2 HP Dual Cylinder air compressor. I cannot find the make and model of ... A: There should be at least two. One for the tank pressure and one for the line pressure. Yes, there ... | |
| household appliances | 4/24/2010 |
| Q: is it hazardous to use household skillets, toaster ovens and microwaves constantly for 6 hours or ... A: It should not be hazardous but you will probably burn them out quite often. It depends on if you ... | |
| Vintage GE Percolator 28P41 seal | 4/24/2010 |
| Q: I have an older GE 28P41 percolator (looke to be about 40 years old). It has a little tube in the ... A: We used to be a GE service center but have not had these parts for years. I think you may be able ... | |
| antique waffle iron | 4/23/2010 |
| Q: Found a white iron and enamel large 2ftx2ft table top double waffle maker in the attic with original ... A: The Edison Electric Co. was one of the first companies to produce small electric appliances. Edison ... | |
| dormeyer mixer beaters | 4/21/2010 |
| Q: I hope you can help me locate replacement beaters for my dormeyer mixer. I have enclosed a picture ... A: I am sending this question to my shop as I do not know if we will have anything or not. I have not ... | |
| Oster Kitchen Center | 4/19/2010 |
| Q: my mother just gave me her Oster Kitchen Center appliance. It's a little noisey when it runs and ... A: These older units tend to dry out and require lubrication. It sounds like this is what your unit ... | |
| Microwave oven | 4/18/2010 |
| Q: I had a fire in my nice new microwave oven, the plastic container I used melted and the paper napkin ... A: Once that smell and color gets into the plastic liner it is very hard to get out. We had a fire in ... | |
| sunbeam mixmaster | 4/18/2010 |
| Q: I have Sunbeam Mixmaster that I inherited and it it's missing the powercord. It is a silver mixer ... A: I think from your description, that your unit takes a detachable cord. If so, please contact us ... | |
| Cofee maker fix | 4/18/2010 |
| Q: My Sunbeam Mr. Coffee coffeemaker Model FTX49 started making a high pitch sound and stopped working. ... A: First of all I have to tell you that Mr. Coffee does not make any internal replacement parts for any ... | |
| Jenn-aire Model JMV8000B | 4/17/2010 |
| Q: I am trying to locate an illustration of the inside of a Jenn-aire Microwave Model JMV8000B so I can ... A: The only place you may find this information is from a Jenn-air authorized dealer. Even then, they ... | |
| dehumidifier | 4/13/2010 |
| Q: My small portable dehumidifier is icing up. What is problem and likely fix. A: There could be no problem at all. This time of year, people try to get their dehumidifiers ... | |
| Dormeyer Mixer Parts | 4/12/2010 |
| Q: My mother has a few Dormeyer mixers, and one of them is a handheld mixer, looks like it might be a ... A: Dormeyer beaters are very hard to find. I have a few left but would have to see an old beater to ... | |
| malfunctioning microwave oven | 4/11/2010 |
| Q: A few days ago my microwave oven began to run continuously EVEN when the door was open. We could ... A: I would replace it as it sounds like the main circuit board is not working properly or there is a ... | |
| countertop blender | 4/10/2010 |
| Q: I have a leak from under the glass portion NOT the base portion. Does it need a gasket of some kind ... A: There should be a rubber gasket between the jar and the cutting assembly. You do not say what the ... | |
| Replacement Carafe | 4/8/2010 |
| Q: I am looking for the 10 cup replacement carafe for the everstar coffee pot, any idea's where I can ... A: I have not been able to locate any source for parts for any Everstar products. Home Depot sells the ... | |
| Sunbeam Mixmaster MMA 175 watts - smells hot | 4/7/2010 |
| Q: I recently received my mother's Sunbeam Mixmaster MMA 175 watts which has not been used for a few ... A: Some of these older mixers collect flour over the years and there is a large resistor that gets very ... | |
| small appliance motors/milkshake mixer | 4/6/2010 |
| Q: I just saw your answer to a person trying to get an old Hamilton B. case apart to replace the ... A: We have repaired many antique appliances but parts are the biggest problem. I do have many old ... | |
| mixer parts | 4/4/2010 |
| Q: do you know where I can purchase 2 brass worm gears that run the beater shafts on a Hamilton Beach ... A: I do not know if we have any brass gears left but I think we may have some plastic ones. Please ... | |
| sunbeam mixmaster 2366 repair | 4/3/2010 |
| Q: I have a black fulcrum piece that hinges the mixer and holds it level. It has come out. How do I ... A: I think you are asking about the trigger assembly located on the stand. It sounds like something is ... | |
| gas stove-surface burners don't light | 4/1/2010 |
| Q: We have a built -in range, the surface burners don't light up with turning gas on until using ... A: I am not familiar with large appliances as we only repair small appliances such as mixers. You ... | |
| Mixmaster won't work | 3/31/2010 |
| Q: I plug my mixmaster 2633-33 in, the light comes on, I move the speed control, nothing, not a sound. ... A: I do not show this model # on the Sunbeam web site listed under hand or stand mixer. If it is a new ... | |
| Espresso Machine | 3/31/2010 |
| Q: My 4-cup Melitta Espresso Machine won't brew. Any suggestions before I go out and buy a new espresso ... A: If it is brewing a little you could try some CLR. You should be able to get some at any hardware ... | |
| 220v Hair dryer rewired to 110v | 3/30/2010 |
| Q: How does one go about to rewire a 220v hair dryer to 110-120v to be used in an normal wired ... A: The only way to use a 220 appliance in this country is to feed 220 volts into the unit. This can be ... | |
| coffie pot top | 3/14/2010 |
| Q: I am looking for a replacement coffie pot top, for a sunbeam model ap74 electric coffie pot. The ... A: We may be able to supply this but you will have to make the request through our shop directly at: ... | |
| kitchenaid stand mixer | 3/12/2010 |
| Q: i need a serial number for my kitchenaid stand mixer model number ksm158gbca. ANSWER: I do not ... A: Every unit has it's own # that is unique to that unit and without seeing the unit there is no way to ... | |
| Hoover fry pan | 3/12/2010 |
| Q: I'm looking for a replacement power cord for a Hoover electric fry pan. The part is a "uniprobe" ... A: This is the old style pan and the only way to retro fit a new probe is to follow the procedure that ... | |
| sunbeam toaster 20-3ag | 3/11/2010 |
| Q: I have some what of a picture of the control area. From the looks of it I am missing a control rod ... A: I am going to send you a parts diagram for this toaster. Maybe it will help you find the part that ... | |
| Hoover fry pan | 3/11/2010 |
| Q: I'm looking for a replacement power cord for a Hoover electric fry pan. The part is a "uniprobe" ... A: If you have the model that has a short stub in the center of two holes on the pan, this has not been ... | |
| Landers, Frary & Clark percolator fuse | 3/9/2010 |
| Q: I am looking for a fuse for a Universal Coffee Percolator made by Landers, Frary %26 Clark, #E 9169. ... A: These have not been available for many years. I do have some new style microtemp fuses that may ... | |
| Looking for Replacement Parts | 3/9/2010 |
| Q: I have a Hamilton Beach Standing Hand Mixer, Model 21. I am looking for the tightening bolt that ... A: This is your lucky day. I just happen to have one left. You know this mixer is over 40 years old. ... | |
| Sunbeam Hot Shot thermal fuse | 3/7/2010 |
| Q: I have a Sunbeam Hot Shot III that needs a new thermal fuse but I can't read it. What should the ... A: I can not say exactly what size fuse that the Hot Shot takes because Sunbeam does not sell any parts ... | |
| hairdryer coils | 3/6/2010 |
| Q: The hairdryer is no longer generating any heat. Everything seems to work find but the coils don't ... A: There are no parts available for any hair dryers that I know of. They are all made in China and ... | |
| Hamilton Beach Mixer | 3/5/2010 |
| Q: I have a Hamilton Beach Stand Mixer that was my Mother's. I was wondering if you would have ... A: The model G was made circa 1950-60. They have two sets motor brushes in them, one set round and the ... | |
| oster food processor shaft/gear | 3/5/2010 |
| Q: I have an Oster model 4250 food processor with stripped gear teeth on the drive shaft/gear assembly. ... A: I am not at the shop this weekend but if you will email this request directly to our web address, my ... | |
| How to repair an old toaster that won't pop up? | 2/23/2010 |
| Q: I have an old Sunbeam toaster from the '50s or 60's that is completely electro-mechanical. It's ... A: There should be an adjustment screw on lower end of the center element. Open the crumb tray and you ... | |
| Dormeyer Mixes | 2/21/2010 |
| Q: My Dormeyer stand mixer, Model SM12 CH, which was my mother's, works fine, except the bowl doesn't ... A: There should be an adjustment screw somewhere on the stand or the mixer. It will adjust the mixer ... | |
| Kenmore (kmx10T) replacement mixer beaters | 2/20/2010 |
| Q: My wife and daughter have used an older Kenmore (KMX10T) 10 speed hand mixer that has performed very ... A: Hamilton Beach and Sunbeam did make mixers for Kenmore and Sears at one time. If you can send me a ... | |
| Hamilton Beech Mixette speed problem | 2/20/2010 |
| Q: I have an old 1950's vintage mixette 3 speed. It's the kind with the switch in the handle and the ... A: Check to see if you broke any wires on the field coil. They are very fragile and can be broken very ... | |
| Hamilton Beech Mixette speed problem | 2/19/2010 |
| Q: I have an old 1950's vintage mixette 3 speed. It's the kind with the switch in the handle and the ... A: There either will be three separate coils in the field or there will be a resistor on the switch to ... | |
| Replacement Probe Control | 2/19/2010 |
| Q: Where can I get a replacement Probe Control - Houselhold Type E23049 (120V - 50/60 Hz 1200 W? A: We stock them but we will have to know what the distance is between center point of the pins on the ... | |
| Soil heating cable | 2/18/2010 |
| Q: I built a propagation box for growing plants from cuttings. I bought two soil heating cables with ... A: You are correct. If you bypassed the therm. and it still did not heat, the problem is in the ... | |
| Kenmore Waffle Iron Model 307 66181 | 2/18/2010 |
| Q: I need to rewire my Kenmore Model 307-66181 Waffle Iron, but need a schematic. Can You help me? With ... A: Kenmore does not have any schematics available for any of their appliances. The only way to rewire ... | |
| Soil heating cable | 2/18/2010 |
| Q: I built a propagation box for growing plants from cuttings. I bought two soil heating cables with ... A: It sounds like more of the China syndrome to me. It seems like everything made in China dies very ... | |
| Everstar DSE 60 crockpot | 2/17/2010 |
| Q: A gift from my wife's mother. It's been sitting in the basement for ages because we have no user's ... A: Good luck in getting any information from Everstar. I can not even find them to ask. I would go to ... | |
| Installing a rheostat for my crock pot | 2/16/2010 |
| Q: I'm not positive this is the right section but i'll give it a go: i have a small crock pot that's ... A: Most crock pots have two different elements, one for high and one for low. You can splice the ... | |
| Elite coffee pot | 2/16/2010 |
| Q: I have a Green & white swril coffee pot. The bottom is marked elite austria and a marking I cant ... A: Sorry, I can not help you on that as we specialize in small electric appliances. If you will go to ... | |
| 1940s? electric broiler superstar brand | 1/11/2010 |
| Q: this is a 'Broil-O-Grill' under Superstar brand (i think it was a toaster mfr called Capitol in NYC) ... A: I think you have stumped me on this one. I have never seen this particular unit but I have seen ... | |
| Dormeyer stand mixer | 1/10/2010 |
| Q: We have a Dormeyer stand Mixer model 3000A #342287. Was wondering if it has any value or if worth ... A: The best way to get a value for any appliance is to go to Ebay and find one similar to what you have ... | |
| cuisinart coffee maker wiring diagram | 1/9/2010 |
| Q: I need a wiring for DCC 2000 I have a brown wire broken off its solder and I'm not sure were it ... A: I am very sure that Cuisinart does not give out this information as we are a service center and can ... | |
| Modern Maid KBH-101 toaster | 1/7/2010 |
| Q: How can I replace/fix them? I've read about trying to locate the same diameter & resistance nichrome ... A: We have repaired a few of these toasters but have used the old elements and repaired them. If you ... | |
| Microwave oven | 1/7/2010 |
| Q: I have a 30? year old Kenmore microwave oven. Recently there has been a reduction in the sound ... A: You have found the stirrer fan. This works when the microwaves pass through it. It disperses the ... | |
| Sunbeam T20b toaster | 1/6/2010 |
| Q: We have an old t20b and it recently stopped toasting. As far as I can tell(forgive me if I describe ... A: I think you are describing the thermostat. It sounds like the bimetal is not working any more. ... | |
| sunbeam mixmaster hm-1 | 1/3/2010 |
| Q: Do you have any idea what year(s) (round about) the Sunbeam Mixmaster hm-1 was produced? We were ... A: Some of these old mixers had the date of manufacture stamped on them. It will probably be stamped ... | |
| Nesco jet stream oven repair | 1/3/2010 |
| Q: I need to know how to replace the orange belt on my oven, I cant seem to be able to remove the ... A: If this is a newer oven, they have been using tamper-proof screws in most applinaces lately. You ... | |
| water filters | 1/2/2010 |
| Q: I have a ge smartwater undersink filter system model gx1s01c,and am wondering if u can use culligan ... A: I have looked for obsolete water filters as well and have had good luck doing a search under "water ... | |
| Mini referigerator | 1/2/2010 |
| Q: I have a mini fridge Magic Chef MCBR360S. It worked fine for a while but now doesn't cool and only ... A: We do not repair any refirdgerators but it sounds like a bad compresson if it just clicks. This is ... | |
| buffet server | 12/31/2009 |
| Q: I have a West Bend Buffet Server - Discovery Collection Model #89000 350 watt 120 volt. ... A: West Bend never made any of their own appliances except for their large coffee urns. They had them ... | |
| rice cooker needs new insert | 12/31/2009 |
| Q: I need a new insert for my salton nutritionist 5.5 cup automatic rice cooker, model number RA6NR. ... A: Salton does not make any replacement parts for any of their appliances as they are all made in ... | |
| Vitantonio Pizzelle Iron that smokes incessantly | 12/30/2009 |
| Q: I have an old Vitantonio Electrica No. 180 Pizzelle Iron that just smokes and smokes. Everything ... A: I have no source for parts for this unit but if it is still heating and not overheating, there is ... | |
| Vitantonio Pizzelle Iron that smokes incessantly | 12/30/2009 |
| Q: I have an old Vitantonio Electrica No. 180 Pizzelle Iron that just smokes and smokes. Everything ... A: If it is not getting overly hot, I would let it heat for at least 30 or 40 min. You can not damage ... | |
| Dormeyer 5100 mixwell | 12/30/2009 |
| Q: I have a Dormeyer 5100 mixwell, that my grandmother bought brand new in the fifties. She passed away ... A: If the motor runs up to speed and sounds good, I would just use it. These were very good mixers. Be ... | |
| Kitchen Aid stand mixer arm stopped holding the bowl up | 12/30/2009 |
| Q: I have a heavy duty Kitchen Aid stand mixer, 325 watts. Somehow the 'arm' that lifts the bowl up to ... A: There is a little plastic piece that usually breaks on these units. You probably have a K-5 model. ... | |
| Vitantonio Pizzelle Iron that smokes incessantly | 12/30/2009 |
| Q: I have an old Vitantonio Electrica No. 180 Pizzelle Iron that just smokes and smokes. Everything ... A: If the smoke is coming from the plates, you should be able to clean them with oven cleaner. If it is ... | |
| kitchenaid mixer | 12/30/2009 |
| Q: The gray plastic covering on the speed lever on my 4-1/2 qt kitchenaid mixer cracked and a piece ... A: We will probably have this part as a used part but you will have to take the cover off of the ... | |
| table top humidifier | 12/29/2009 |
| Q: I use old KAZ evaporative humidifiers around the house in winter. Very simple to use and maintain. ... A: You will get some humidity in the air simply by moving air over the water but not enough to do much ... | |
| Dormeyer Hand mixer/milkshake blender | 12/29/2009 |
| Q: I have a Dormeyer milkshake mixer or "Drinkmixer model 7000" as it is called. When I plug it in, it ... A: My guess would be lack of lubrication on the armature. This mixer has to be at least 25 years old ... | |
| Sunbeam Automatic Mixmaster | 12/29/2009 |
| Q: I have recently been given a Sunbeam Mixmaster stand up mixer with the serial number 1160662. It is ... A: I do not have any records for serial #s but the model 3 was made either in the late 1930s or early ... | |
| replacement of large bowl | 12/29/2009 |
| Q: My daughter broke the large bowel of my mother's Sunbeam Mixmaster. We can't read the model number ... A: Sunbeam made two different bowls for the old mixers. One had a turntable that was metal and had ... | |
| older Sunbeam Mixmaster Electornic model # | 12/29/2009 |
| Q: I can't find any model # for my older Sunbeam Mixmaster. It only says "Sunbeam Mixmaster Electronic" ... A: We will either need a model or service # for the mixer to get the correct beaters. The service # ... | |
| 1-7A Sunbeam mixmaster | 12/27/2009 |
| Q: I need to reset the gears on this unit so that the beaters are not hitting each other, I have the ... A: If you have the top cover off of the machine, there is a metal cover that covers the gears. Remove ... | |
| Coffee maker woes | 12/27/2009 |
| Q: I fill my coffee maker with a complete carafe of water and only a little bit of coffee comes out. ... A: It sounds like you have a thermostat or check valve problem. Either the brew thermostat is not ... | |
| broken handle | 12/26/2009 |
| Q: I have a Frigidaire model FMV156DCC. The door handle has broken off. Is there anyway we can ... A: We do not service large appliances so I am not familar with this model. I think most of the handles ... | |
| Sunbean Mixmaster speed control? | 12/26/2009 |
| Q: The handle came loose and I had to take it apart to refit. when I put it together, I thought all ... A: If you have a model 1-7a, MMA, MMB or simular model, there is a small hole in the cap where you can ... | |
| GE hand mixer 30M47 | 12/25/2009 |
| Q: I always use this mixer when baking. It was passed down from my mother. This mixer mixes just as ... A: Not all companies stamped their appliances with the date code. By the model # that you give, I ... | |
| Pizzelle maker | 12/25/2009 |
| Q: My Vitantonio pizzelle maker died halfway through my Xmas baking! My husband looked at it and found ... A: We sell wire to do just what you are wanting to do. We use it for waffle irons and toasters. To ... | |
| mixmaster mma dough hooks | 12/23/2009 |
| Q: My MMA beaters have two slots, crossed at 90 degrees to each other, I see dough hooks that seem to ... A: No, if the dough hooks will fit your machine it will not be a problem. The new replacement beaters ... | |
| burning smell from kenmore stand mixer | 12/22/2009 |
| Q: mixer started to smell like burning electric, light smoke coming out of motor area. i took it apart ... A: The burned resistor would definitely cause your problem but just replacing the resistor may not ... | |
| Mixer has ONE speed-FAST | 12/22/2009 |
| Q: Mixer is about 22 years old. KitchenAid K45SS-WH . About a month ago I turned it on %26 it only runs ... A: It sounds like you have one of the older K45 that still has a capacitor in it. When the capacitor ... | |
| burning smell from kenmore stand mixer | 12/22/2009 |
| Q: mixer started to smell like burning electric, light smoke coming out of motor area. i took it apart ... A: I do not know what a Kenmore mixer looks like on the inside but it probably looks like any other ... | |
| T-fal oven | 12/21/2009 |
| Q: Weowna T-fal anvante elite oven, and whie toasting bread last night, it decided to quit. I am ... A: These fuses look more like a diode and are metal with a lead coming from each end. It will have ... | |
| Dormeyer 4200 | 12/21/2009 |
| Q: Was my mother's. Now fixing up for my daughter (a retrophile). Beaters seem to not go in all the ... A: It sounds to me like you are on the right track. Sunbeam has a similar system to eject the beaters. ... | |
| Mixmaster MMA dough | 12/20/2009 |
| Q: Is there a dough hook for the Sunbeam Mixmaster MMA? We have our mothers original mixer that seems ... A: I do not think Sunbeam ever made dough hooks for their older mixers. I can not remember ever seeing ... | |
| Universal Landers Frary & Clark Mixer | 12/20/2009 |
| Q: I have a very nice old mixer that runs great but need Beaters. Shaft is .246 approximate and about ... A: Landers Frary and Clark was a large dept. store that had the Universal Appliance Co. make appliances ... | |
| Vintage Sunbeam Electric Skillet | 12/19/2009 |
| Q: I have a vintage Sunbeam Electric Skillet Model FPL-5. The handle has a list of frying temperatures ... A: I do not have anything that will give me that information but you can try one thing. Water will ... | |
| dormeyer mixer deluxe 250 beaters | 12/19/2009 |
| Q: wayne i am trying to locate beaters for my dormeyer 10 speed deluxe 250 mixer i do not have a parts ... A: They are very rare but if you have a picture of one of your old beaters that you can send to me, I ... | |
| heater | 12/18/2009 |
| Q: my question is simple i think. i have looked at some ceramic heaters and related type heaters since ... A: If I were going to use one of these heaters, I would place some type of non-flammable surface on the ... | |
| T-fal oven | 12/18/2009 |
| Q: Weowna T-fal anvante elite oven, and whie toasting bread last night, it decided to quit. I am ... A: We stopped repairing T-fal appliances years ago because of the problem that you are having with the ... | |
| sunbeam mixer replacement beaters | 12/16/2009 |
| Q: I have a deluxe sunbeam mixmaster mixer from the mid 1980's, I need replacement beaters. I can not ... A: I think that the model # that you give is an old Sunbeam part # but not sure. It does not look ... | |
| Oster Kitchen Center | 12/14/2009 |
| Q: Do you know where I can get a replacement switch for an Oster Kitchen Center model 900? If parts ... A: Is your model just a 900? The reason I ask it that there are about 50 900 series numbers and they ... | |
| Sunbeam Mixer | 12/14/2009 |
| Q: The speed knob on my mixer is becoming very hard to turn. I removed the knob, made sure everything ... A: The only thing that the knob does is turn the unit on and slide the speed control up and down. The ... | |
| Dormeyer Stand Mixer | 12/14/2009 |
| Q: I have an old Dormeyer Stand Mixer Model #3200 the number stamped #517757 made in Chicago USA. It ... A: People are always looking for Dormeyer parts and so if you are looking to sell the mixer, I'm sure ... | |
| Waffle maker | 12/14/2009 |
| Q: I wanted to see if you could help me out. I have a waffle maker (Toastmaster model #277) which is ... A: If your thermostat is a little disc type that is about 1/2" in dia. and has two spade terminals on ... | |
| Sunbeam T-20 Toaster | 12/12/2009 |
| Q: Our faithful T-20 no longer lowers the toast and heats up. Based on your experience, can I fix this? ... A: There are two different adjustments that have to be balanced on this toaster before it will work ... | |
| looking for part for old ge meat grinder | 12/12/2009 |
| Q: i have a old ge meat grinder model #20001 the end piece of the auger broke. Where may i go to find ... A: These were very rare as GE did not make very many of them. This means that parts are also very ... | |
| Sunbeam automatic mixmaster | 12/12/2009 |
| Q: I just bought a Sunbeam mixmaster 7 B-1 and a 10 A. They both work but should probably be checked ... A: I do not have a list of service centers in the country but I do know that there are very few of us ... | |
| sunbeam mixer | 12/11/2009 |
| Q: I need a replacement power cord for my two old Models MMB and 12C Sumbeam mixers. Please advise. ... A: The MMB takes the plug-in type cord and we have them in stock. I am not sure about the #12 as some ... | |
| sunbeam oster kitchen center 1984 | 12/11/2009 |
| Q: My manual for this appliance got thrown out by mistake. Can you let me know where I may purchase ... A: Manuals have not been available from Oster for over 15 years but we do sell a copied manual for ... | |
| Re Oster Kitchen Center, beaters won't stay inserted | 12/10/2009 |
| Q: Wondering if you can help me figure out an issue with an Oster Kitchen Center I just purchased on ... A: The 5550 model was only made one year and parts for this unit are very rare. I do have some used ... | |
| Re Oster Kitchen Center, beaters won't stay inserted | 12/9/2009 |
| Q: Wondering if you can help me figure out an issue with an Oster Kitchen Center I just purchased on ... A: You have to replace the gears that the beaters fit into. There are small snap rings that hold the ... | |
| Craftsman aircompressor 5kcr49sn2038cx | 12/9/2009 |
| Q: I need a piston ring and cylinder for the listed model. the counter balance came loose & through the ... A: We have parts for Devilbiss, Cole-Powermate, Black Max and Senco compressors. Sears has their own ... | |
| craftsman garage opener | 12/8/2009 |
| Q: Haven't heard from her yet,but I guess she's busy. Anyway this is the third time I've run into this ... A: If you do not hear from Caryl in a day or so, e-mail her again as she always answers email. It may ... | |
| oster kitchen center | 12/8/2009 |
| Q: My son was making cookies and put chocolate chip in with the rest of the batter in the mixer. (his ... A: I do not know what model # your unit is but usually they are worth repairing. We have some base ... | |
| CRAFTSMAN 3/8 DRILL BATTERY #982138-001 | 12/8/2009 |
| Q: I have CRAFTSMAN 3/8 DRILL and its BATTERY #982138-001 does not recharge-it keeps showing orange ... A: I have not seen this web site before but it may be worth the money that he wants just to try it. If ... | |
| Vintage Hamilton Beach Scovil chrome stand mixer | 12/7/2009 |
| Q: I saw you helped someone else concerning this model. My mixer is making a creeching noise and I ... A: We specialize in repairing older small appliances. I do not know of any other shop that does what ... | |
| Sunbeam Mixmaster Beaters | 12/7/2009 |
| Q: I am trying to find replacement beaters for my mom's Sunbeam Mixmaster. She is having trouble ... A: Yes, we have these beaters in stock. The obsolete part # gives me all I need to identify the ... | |
| Dormeyer powermix stand mixer | 12/7/2009 |
| Q: I have a Dormeyer model 70 mixer. The motor is in good shape but the gear that drives one of the ... A: I know that on some Sunbeam models we are able to reverse the two gears and make the accessory drive ... | |
| Sunbeam Vista Mixmaster | 12/7/2009 |
| Q: I inherited a Sunbeam Vista Mixmaster from my mother.It is in great shape with 2 sets of beaters and ... A: Sorry but there never was a lock for the up right position on this mixer. If you ever require parts ... | |
| sunbeam mixmaster MMB parts | 12/6/2009 |
| Q: .Can you tell me where I can buy parts for this mixer? I need the cast metal spring loaded ... A: I think we will have this part in stock. Please order from us at: info@kieferappliance.com We will ... | |
| sewing machine | 12/6/2009 |
| Q: My old White Rotary sewing machine which is probably from the 30s or 40s took issue with trying to ... A: I do not know much about sewing machines but my one of my technicians loves to work on old sewing ... | |
| hobart mixer | 12/6/2009 |
| Q: I'm not sure if you can help with this question. I have an old hobart A200 #3943 bench mixer. It is ... A: Hobart still has stores around the country. Contact one of them and see if they still have any ... | |
| 1950 Sunbeam Radiant Control Toaster | 12/5/2009 |
| Q: I recently acquired the toaster my parents received as a wedding gift. It appears to work ... A: I do not think that Sunbeam ever used asbestos in any of their toasters. Most of the toaster ... | |
| Hamilton Beach Scovil Solid State Blender | 12/5/2009 |
| Q: Happy Holidays, I am unable to attach the beaters to a Hamilton Beach Scovil Solid State Blender. ... A: I am sorry to have to tell you but the gears are likely stripped inside the mixer. There is nothing ... | |
| powercord for warming trays | 12/4/2009 |
| Q: I have 2 different warming trays and the power cords are MIA. Salton model #H940 series r, and ... A: Most warming trays take the same cord but please measure the distance from center to center on the ... | |
| Sunbeam Power Plus Mixmaster circuit board | 12/3/2009 |
| Q: I have a Sunbeam power plus mixmaster (circa 1977) Model 1-150 and Service # 1-15H, and the speed ... A: I think from the model # that this is a hand mixer. Sunbeam never sold any internal parts for this ... | |
| comSunbeam Vista Mixmaster, service no.70190 | 12/3/2009 |
| Q: Good Morning, I hope you can help me. My mixer has a mind of it's own! I now have to turn it to 6 ... A: I think you have a 701-9C service #. It is difficult to tell on the stamping. I think maybe the ... | |
| beater for Dormeyer | 12/2/2009 |
| Q: I need a beater for a dormeyer 10 speed deluxe 250 stand mixer. I think it would be circa 1960. I ... A: If you have one beater and can take a picture of it and send it to me, I will try to match it with ... | |
| General Mills Appliances | 12/2/2009 |
| Q: Wayne, I recently saw a post you made regarding a question someone had on a General Mills appliance. ... A: This is very good information to have. It sounds like it came directly from the source and you ... | |
| KitchenAid mixer | 12/2/2009 |
| Q: I have been wanting to buy a KitchenAid mixer but now am hesitating because of all the reports of ... A: If it is a K-5 or K-45 it has an AC motor. Only of few of these units had the leaking problem. The ... | |
| KitchenAid mixer | 12/1/2009 |
| Q: I have been wanting to buy a KitchenAid mixer but now am hesitating because of all the reports of ... A: It is generally some of the older units that leak oil but they are built much stronger than the new ... | |
| Sunbeam Parts | 12/1/2009 |
| Q: I am trying to find a control plate for my vintage Sunbeam mixmaster, model 7 B, does anyone know ... A: We have many used mixers that we keep for parts only but I do not know if we would have what you ... | |
| Rewire a Sunbeam mixer | 12/1/2009 |
| Q: Is it expensive to rewire a mixer? I have found a great aqua mixer from the 50's but the cord looks ... A: The cord cost is $8.95 and if we install it we usually oil the armature as well at a cost of about ... | |
| dormeyer mixer | 11/30/2009 |
| Q: i am trying to replace the cord on a dormeyer 4200 power-chef mixer,but cannot get to the wiring ... A: I am sorry but we never had any books, of any type, for Dormeyer as they stopped production over 20 ... | |
| Sunbeam Heritage Stand Mixer #2349 | 11/30/2009 |
| Q: My Sunbeam Heritage Stand Mixer #2349 would blow my GFCI with even a very light mixing load. The ... A: This mixer was made in 2003 and Sunbeam does not carry any parts for it any more. That said, I ... | |
| Rewire a Sunbeam mixer | 11/29/2009 |
| Q: Is it expensive to rewire a mixer? I have found a great aqua mixer from the 50's but the cord looks ... A: Most Sunbeam mixers can be rewired with a new 3 wire grounded cord. This is the only type of cord ... | |
| Sunbeam 1150 Watt Immursable Fry Pan Model RM5 | 11/28/2009 |
| Q: My mom has a stainless Steel electric fry pan that is at least 40 years old. The pan works fine, ... A: This is probably the best pan that Sunbeam ever made but she is having the same problem that a lot ... | |
| Farberware percolator repair | 11/27/2009 |
| Q: My 4 to 8 cup Farberware percolator does not heat completely. I took off the bottom to check the ... A: One is the brew thermostat and the other is the over limit thermostat. It is similar to a fuse but ... | |
| Oster kitchen center | 11/27/2009 |
| Q: I have misplaced the beaters to my oster kitchen center model 5500. I know they do not make those ... A: The 5500 is a very rare model as Oster only made it for one year and then stopped making all parts ... | |
| oster toaster oven replacement knob | 11/26/2009 |
| Q: Where can I get a replacement knob for my oster toaster oven model 6232-015? A: According to the Sunbeam web site, the only parts available for this unit are the racks, feet, and ... | |
| 1968 sunbeam mixmaster | 11/26/2009 |
| Q: how do you oil the mixmaster? A: You do not list a model # so I can not tell exactly what you have but I will try. The mixers with ... | |
| Modle #7500 | 11/26/2009 |
| Q: My husband bought me this hand help mixer at a garage sale 6 or 7 years ago and I would like to know ... A: Dormeyer has been out of business for over 25 years so it is older than that. I do not have any ... | |
| Firestone Turkey roaster | 11/25/2009 |
| Q: Do you have any information on a Firestone Turkey roaster circa 1940's? I know it is over 50 years ... A: Most of the roasters from this era were the Nesco brand. I am not sure if Firestone ever made a ... | |
| garbage disposal | 11/25/2009 |
| Q: My disposal stopped working.. I tried the reset button. moving the blades.. it no longer makes a ... A: If you have a volt meter or voltage test light, plug in into the outlet and see if you have 120 ... | |
| antique toaster element | 11/24/2009 |
| Q: Wayne,we have and antique Star Rite toaster. It is very cute and until recently was functioning. ... A: This is a neat toaster and is rare. We have some nichrome wire that may fit your application. I ... | |
| rebuilding/upgrading sunbeam 7b mixmaster | 11/24/2009 |
| Q: I have a sunbeam mixmaster 7b that's been used a lot, speed control doesn't work smoothly. I bought ... A: The original beaters and dough hooks for the old mixers had a cross on the top of the stems. This ... | |
| Dishwasher shutoff | 11/23/2009 |
| Q: I have a Maytag portable dishwasher that hooks up to my kitchen faucet. Problem: if I want to run ... A: I am only familiar with small appliances as this is our market but I would think that such a device ... | |
| Kenmore waffle iron | 11/23/2009 |
| Q: I need a power cord for a Kenmore waffle iron, model # 3 )or maybe 8)076460. ty A: I think we have what you need for this appliance. Please measure the distance between the center ... | |
| Sunbeam Mixmaster Heritage Series 2346 | 11/23/2009 |
| Q: I have a 3 year old Sunbeam Mixmaster Model 2346 that will no longer work properly. The beaters ... A: I checked the Sunbeam web site and they do not have new stands or parts for the stand available. ... | |
| Sunbeam T-20 Toaster | 11/23/2009 |
| Q: Wayne, I have a toaster that was given to my parents for their wedding and still functions near ... A: --- On Tue, 12/1/09, kieferappliance <info@kieferappliance.com> wrote: From: kieferappliance ... | |
| Compressor -regulator | 11/23/2009 |
| Q: Have a small air compressor with a regulator and gauge on it. The gauge is fine but the regulator ... A: No. There is no real repair to regulators. You do not say what brand you have but most regulators ... | |
| New HB hand mixer | 11/22/2009 |
| Q: I bought a Hamilton Beach hand mixer a year ago. While I was mixing dough it just stopped. It didn't ... A: All new Hamilton Beach appliances are made in China and are not made to repair. If you really feel ... | |
| mixer | 11/22/2009 |
| Q: i have a GE hand mixer # D3M47 gold color could u tell me how old this is and what it worth? A: Hand mixers are not in real high demand right now. The best way to try to get a feel for worth is to ... | |
| Sunbeam mixmaster 10 | 11/22/2009 |
| Q: I just bought a Sunbeam mixmaster 10 at an estate sale. It works. It came with a juicer but I ... A: I think that the model 10 has a beater ejector attached to the handle. If you push the handle hard ... | |
| Sunbeam Mixmaster PowerPlus | 11/22/2009 |
| Q: The thing looks great and has all the attachments except the turntable is not turning. The beaters ... A: Does your mixer have a shift lever that allows for the large and small bowls? If so there should be ... | |
| hoover waffle iron model #6676 replacement power cord | 11/21/2009 |
| Q: Not sure if I posted this question already, but we inherited a barely used Hoover waffle iron model ... A: There may be a post in the center between the two pins. If not a post, maybe a hole. If there is a ... | |
| Sunbeam Mixmaster PowerPlus | 11/21/2009 |
| Q: The thing looks great and has all the attachments except the turntable is not turning. The beaters ... A: The beater with the small plastic tip on it should drive the bowl. If it is not, you can do a few ... | |
| Sunbeam Mixer Heritage Series, 2350, 2352 | 11/20/2009 |
| Q: The bowl won't stay seated on the pedestal; it keeps tipping when the beaters meet any resistance ... A: Try to adjust the mixer head so there is not so much pressure on the beaters. There should be an ... | |
| rebuilding/upgrading sunbeam 7b mixmaster | 11/19/2009 |
| Q: I have a sunbeam mixmaster 7b that's been used a lot, speed control doesn't work smoothly. I bought ... A: The only place that you may find some dough hooks for a #7 would be Ebay and be sure they are for ... | |
| Harvest Maid Perserver Model FD-101 120volts 60Hz 525 watts UL listed 885C | 11/19/2009 |
| Q: I have the above dehydrator which I bought brand new somewhere between 1978 and 1982. The Fan only ... A: Yes, I was plant manager with Trek when all of the frames were hand brazed. Now they are all glued ... | |
| Sunbeam Mixer Heritage Series, 2350, 2352 | 11/18/2009 |
| Q: The bowl won't stay seated on the pedestal; it keeps tipping when the beaters meet any resistance ... A: I found a picture of a 2356 and I think they are very similar. Two things to check. Check the ... | |
| power cord | 11/18/2009 |
| Q: I have a Hoover stainless steel electric frying pan with a domed lid. The power cord is in pretty ... A: The probe control is no longer available for your Hoover, if you have the probe that has two small ... | |
| Sunbeam Mixmaster Vister model V14cws | 11/18/2009 |
| Q: I have a Sunbeam Mixmaster mixer model V14CWS in excellent working condition except for the ... A: If you can take a picture of the area with the bearing in it as well as the turntable,I will see if ... | |
| rebuilding/upgrading sunbeam 7b mixmaster | 11/18/2009 |
| Q: I have a sunbeam mixmaster 7b that's been used a lot, speed control doesn't work smoothly. I bought ... A: We repair a lot of these old mixers but the only way to get a higher wattage mixer would be to ... | |
| Vintage ge coffee percolators | 11/17/2009 |
| Q: Can anyone tell me the chronological history of the models of general electric coffee percolators ... A: Universal Appliance Co. was purchased by General Electirc in the 60's. Then Black and Decker bought ... | |
| Honeywell 13520 | 11/17/2009 |
| Q: I am sure it is a motor issue. Any way to tune up these little motors? (Brushes, bearings etc..) ... A: You do not say what kind of unit this is but there is no real tune-up to small motors. If you are a ... | |
| dish washer | 11/16/2009 |
| Q: I have a GE Dishwasher. It drains water from top of the sink when runs. I think it is called air ... A: The silver cap on top of the sink should be for an air vent. There should be no water in this area. ... | |
| mixmaster yellowed with age | 11/16/2009 |
| Q: My oster mixmaster has yellowed with age - the back is still white but the front has yellowed. Is ... A: If you have a Kitchen Center and the case is plastic, there is nothing you can do but replace it. If ... | |
| 50's dormeyer mix master | 11/16/2009 |
| Q: I have an older model dormeyer and I just don't want to get rid of it. Last time I used it it worked ... A: If you would like to send it to us we can see if it is repairable and at what cost. Then you can ... | |
| burning terminal pins | 11/14/2009 |
| Q: I have my grandmother´s Farberware percolator, model Superfast 138, and am having to replace the two ... A: Yes replace the cord as well. The cord terminals are not holding tightly to the pins and they are ... | |
| Sunbeam Mixmaster Model 12 overheating at low speeds | 11/11/2009 |
| Q: I found this mixer in a sad state and have refurbished it as best as I can, So it's had a thorough ... A: I would recommend that you replace the resistor and capacitor. I have new replacement units but you ... | |
| Coffee Pot Cord Replacement | 11/9/2009 |
| Q: Is it possible to replace the electrical cord on a Cuisinart DCC-2000 Series coffee pot. The coffee ... A: You should be able to replace the cord yourself if you can get the bottom off of the coffee maker. ... | |
| waffle iron with name Black & Decker | 11/9/2009 |
| Q: Having picked up a waffle iron at a thrift shop, i was surprised to see the name on the waffle iron ... A: Landers never did make appliances, they just sold them. The Universal Co. made the appliances and ... | |
| Sunbeam Mixmaster Model J | 11/8/2009 |
| Q: I will have my wife make a picture and we will send it to you. It looks exactly like the later ... A: This cord would be very difficult to replace on this mixer as the wires are wired into the small ... | |
| Sunbeam Deluxe Mixmaster Mixer | 11/8/2009 |
| Q: I have a Sunbeam Deluxe Mixmaster Mixer with Dough Hooks. The box says it is 01080 Chrome. It is ... A: I do not have any books here to look up this model but if it is an older unit there should be an ... | |
| Sunbeam Mix Master | 11/8/2009 |
| Q: In the middle of mixing my Sunbeam Mixer just quit. The only part number I can find is: service no. ... A: I think if you have a model 9C that your mixer was made in the late 50's. I think you are refering ... | |
| cord for gr 100 griddle | 11/8/2009 |
| Q: do you know where we can purchase a black and decker griddle cord.? than you A: If it is one with the small probe control, they are not available and no substitute. If it is the ... | |
| sunbeam mixer | 11/6/2009 |
| Q: My speed control only operates on high speed and I mean HIGH. I cleaned it but it didn't solve the ... A: If a older type Sunbeam only runs on high the first place to look is the capacitor. If you repalace ... | |
| Oster Kitchen Center | 11/6/2009 |
| Q: Our Oster Kitchen Center only operates at high speed, regardless of where the speed control knob is ... A: The capacitor replacement will work on mixers but not on Kitchen Center bases. If you have a base ... | |
| hampton bay ceiling fan | 11/6/2009 |
| Q: I have a Hampton Bay ceiling fan with four lights on it. It as a remote control as well. Within 2 ... A: It was probably made in China and has very cheaply made sockets. These sockets cause a lot of ... | |
| Sunbeam electric skillet power cord | 11/5/2009 |
| Q: I have an old Sunbeam electric skillet Model #FP-11A with the control unit on the handle. The power ... A: You have to measure the distance between the center points on the prongs on the fry pan not on the ... | |
| sunbeam waffle baker CG-1 | 11/5/2009 |
| Q: Have it for ever love it Light just went out Can it be repaired? Tells me when waffle is done ... A: The light is connected to the thermostat and when it opens the light turns on. I would have to see ... | |
| info on antique electric portable stove | 11/5/2009 |
| Q: I was wondering if there are any sites/links you can direct me to that will tell me any info on a ... A: It was made by the Universal Electric Co. not Landers, Frary and Clark. They were a large dept. ... | |
| Mixmaster 60th Anniversary Ed. Stand Mixer | 11/4/2009 |
| Q: I have a c.1990? Sunbeam 12-speed Mixmaster 60th Anniv Stand Mixer that works great, but I have to ... A: There is a little tab on the control cap that turns the switch off. That tab may have broken of is ... | |
| Older KitchenAid Unopened | 11/3/2009 |
| Q: Kiefer, My husband and I have an old KitchenAid 'Multi-Function Ultra Power Mixer'- a wedding gift ... A: The olny problem that you may have with this mixer is that with the grease that Kitchenaid used in ... | |
| VTech 900 MHz Cordless Phone | 11/2/2009 |
| Q: How do I change the recorded message on this item? LLT A: Sorry but we do not service phones as they are not serviceable and every one has a different set up ... | |
| timer motor | 11/1/2009 |
| Q: I need a replacement motor for a timer for my Whirlpool Dryer. The motor came off of a unit that ... A: We only service small appliances so I can not help you with this motor but there are many large ... | |
| Dormeyer Mixer 4300 | 11/1/2009 |
| Q: I also have a Dormeyer Mixer 4300. It works very well but I got a beater stuck that will not come ... A: Beaters are held into the drive gears by a spring or snap ring on the end of the beater. They ... | |
| Sunbeam Mixmaster Model 12 | 11/1/2009 |
| Q: Apparently the Model 12 was manufactured from 1957 through 1967...I have recently acquired this ... A: I think we will have a used one in stock but you will have to request it through our business ... | |
| Sunbeam MixMaster Model MMB | 10/31/2009 |
| Q: My wife's mixer began working intermittently %26 then not at all. We heard something rattling around ... A: We use 150 ohm resistors in all of the Sunbeam mixers and they work just fine. The one that you ... | |
| hamilton beach hand stand mixer | 10/30/2009 |
| Q: i bought the hamilton beach hand stand mixer and i want to know if the turntable doesn"t spin by ... A: The bearing is located in the stand where the turntable is inserted. Lift the turntable off of the ... | |
| hamilton beach hand stand mixer | 10/30/2009 |
| Q: i bought the hamilton beach hand stand mixer and i want to know if the turntable doesn"t spin by ... A: You could have two problems. One is that the bearing on the bottom of the turntable is not ... | |
| Sunbeam (Mr Coffee) Thermister Replacement | 10/30/2009 |
| Q: I'm an out of work technician so trying to cut corners hence this question. My coffee maker decided ... A: This coffee maker is made in China and Mr. Coffee does not supply any internal parts for any of ... | |
| slumber-magic adjustable bed | 10/30/2009 |
| Q: where do i buy a remote and a user manual for this bed..i've been searching for days..i bought a ... A: Sorry, I have had no contact with this company so am not going to be able to help you much. I would ... | |
| food dehydrator | 10/30/2009 |
| Q: We have an older HARVEST MAID food dehydrator. It is not heating..can I fix it? I need a list of ... A: I have not found a source of parts for this brand. I think they are made in China and I do not ... | |
| doremeyer mixer model 4201 | 10/29/2009 |
| Q: I am looking for beaters and bowls for this model. Can you help me locate. I would greatly ... A: I have some beaters for Dormeyer but the most common ones are gone. Your best chance is to go to ... | |
| replacement cord | 10/28/2009 |
| Q: Wayne, I have a Sunbeam T-20B toaster, the cloth cord has gone bad. Do you know where I can ... A: I do have a few of the good used cloth cords left. They are original cords so they are not new but ... | |
| Oster Kitchen Center | 10/28/2009 |
| Q: I have an Oster Kitchen Center. Something cracked during bread making. I feel it is a gear but I ... A: We can repair most Kitchen Centers. Please send it to us at: Kiefer Appliance, 4511 Monona Dr., ... | |
| G.E. electric skillet | 10/27/2009 |
| Q: I have had a G.E. electric skillet that I love since the late 70's. My power control is burnt out. ... A: Sorry, but this is the only control unit that will fit on your skillet. No other company used this ... | |
| Sunbeam Mixmaster Model J | 10/24/2009 |
| Q: Purchased at yard sale for $1. Stamped on outside was Sunbeam Mixmaster Model J 110-120 volts AC-DC ... A: As a Sunbeam service center for over 25 years, we have not seen many Model J's. I do not have any ... | |
| Wafffle maker | 10/23/2009 |
| Q: I am in search of an electrical cord for a Landers, Frary & Clark, Universal, Model #9305, waffle ... A: These cords have not been available for many years but you can use two separate cords if they are ... | |
| beater for a dormeyer mixer | 10/22/2009 |
| Q: I AM NEEDING BEATERS FOR A DORMEYER MIXER MODEL 5700 SERIAL NUMBER 0424465801. CAN YOU TELL ME ... A: I do not have any books on Dormeyer any more but I do have some new and used beaters for some ... | |
| hamilton beach slow cooker | 10/22/2009 |
| Q: I broke the ceramic pot and lid of a Hamilton Beach/Scovill 4 quart slow cooker called Simmer-on ... A: Sorry, we use to carry these before Hamilton Beach moved their production to China. Now there are ... | |
| Vintage Hamilton Beach Chrome Mixer Timer Dial | 10/21/2009 |
| Q: I recently acquired a vintage Hamilton Beach (silver) chrome stand mixer. The timer dial is ... A: Hamilton Beach and Scovill merged just before this mixer came out. The Scovill name was dropped a ... | |
| Blue Ice 80533 | 10/19/2009 |
| Q: I have a Blue Ice 80533 ice making machine which has suddenly stopped working. All the lights work ... A: It sounds like you have diagnosed the problem to the main circuit board. I think you are probably ... | |
| Sunbeam Mixmaster MMA speed control, attachment compatibility | 10/18/2009 |
| Q: Kiefer, I have read your other Mixmaster answers with interest. Thank you! Just cleaned and ... A: It has been a while since I have worked on a MMA mixer but if I remember correctly, there are two ... | |
| 15091 Singer Sewing machine | 10/15/2009 |
| Q: I rewired the light and foot peddle. When I plugged it in, it blew the fuse and the wall socket is ... A: I am not a specialist in sewing machines but one of my repair people has worked on them for years. ... | |
| 15091 Singer Sewing machine | 10/14/2009 |
| Q: I rewired the light and foot peddle. When I plugged it in, it blew the fuse and the wall socket is ... A: You have a direct short in two wires inside the peddle. The two wires from the cord can not touch ... | |
| Hoover shampooer F7425-900 | 10/14/2009 |
| Q: I am missing the very end of the trigger for the accessory hose. I was told that I had to buy the ... A: I am not going to be much help as we do not service any Hoover products. It does not supprise me ... | |
| Dormeyer model 4200 | 10/12/2009 |
| Q: I recently purchased this but the cord needs replacing. Could you replace it for me? And what would ... A: Yes, we can replace the cord for you but we always use three wire grounded cords. The cost is about ... | |
| Maytag upright freezer | 10/12/2009 |
| Q: The guys at Major appliances have been maxed out, so maybe you can answer my question? My 5 year old ... A: We do not service freezers, only small appliances, but it sounds like your compressor may be ... | |
| Hamilton Beach NO.33 | 10/12/2009 |
| Q: Do you have a pair of carbon brushes with or without the springs for a Hamilton Beach NO.33 milk ... A: Yes we do but you will have to request them directly from our shop. Either call us at:608-221-3322 ... | |
| Sunbeam Mixmaster | 10/8/2009 |
| Q: I have an old Sunbeam Mixmaster, the only number I see on it is 533168. It was working fine but ... A: I think that you will find if you do not use a GFI outlet, it will probably work just fine. If it ... | |
| Sunbeam Skillit Model 3001-000 | 10/7/2009 |
| Q: Mr.Kiefer, I have a sunbeam electric skillet model 3001-000. I believe the control unit has gone ... A: This is an older model skillet and Sunbeam does not have a parts sheet on the web site. If you will ... | |
| samsung microwave | 10/7/2009 |
| Q: yesterday the microwave stopped heating food. today it is flashing "e 1" and still not heating. ... A: It sounds like the main control pc board is not working properely. This repair will cost more than ... | |
| Oster Kitchen Center 900 Series | 10/7/2009 |
| Q: I have a Oster Kitchen Center 900 Series and never had a problem until today. The beaters will not ... A: Probably, but we would have to see the unit. It sounds like you need some new gears. The beaters ... | |
| Nostalgia RIC-100 Retro Ice Maker | 10/6/2009 |
| Q: Purchased in April 2009. Stopped making ice last week. Distributing mechanism works to push out ... A: I do not think you will find any repair shop that will work on these units as parts are not ... | |
| Hamilton Beach mixer | 10/5/2009 |
| Q: I have an old Hamilton Beach Scovill mixer, model 25. When I use it on low it smokes and my husband ... A: The old Hamilton Beach mixers have a mechanical/electrical speed control and the brushes and ... | |
| ceiling fans - replancing rotary light switch | 10/4/2009 |
| Q: I have an old house, built in the 1920's. Knob %26 tube wiring. We installed a Hunter ceiling fan ... A: With out being there to test the circuits I will have no way of telling. If you only have a switch ... | |
| KITCHENAID MIXER DIED | 10/4/2009 |
| Q: MY WIFE WAS MIXING A BATCH OF COOKIES AND THE MIXER DIED. IT SOUNDED AS IF IT WAS BATTERY POWERED ... A: It sounds like it may be brushes or the bearings could have overheated and tightened up due to lack ... | |
| Black & Decker ICR200 | 10/3/2009 |
| Q: My Black & Decker First Impressions (ICR200) iron lights up, but won't heat. It's about 2 years old. ... A: It could be a fuse that overheated or sometimes the auto shut-off circuit board goes out. It may be ... | |
| Leaky Iron | 10/3/2009 |
| Q: I bought an expensive Rowenta iron thinking I would be getting quality. It's about 4 years old and ... A: Some Rowenta irons have a thermostat problem. It is not a high quality unit and it gets weak after ... | |
| Sunbeam toaster: Model T-35 | 10/2/2009 |
| Q: I love my toaster and have had it for over 20 years. It still works, but needs service. I was ... A: We probably can service your toaster. It all depends on what it needs as there are no new parts ... | |
| high temp wire | 10/1/2009 |
| Q: We are trying to locate 18ga. flexable, woven, high temp wire, and end connectors for posts. Must be ... A: We carry it but would have to know what type of connectors to crimp onto the ends and the exact ... | |
| DeLonghi Microwave Oven | 10/1/2009 |
| Q: I have a Delonghi 800W Microwave oven (model: MM821AAN). The paintwork on the inside of the door is ... A: You should be able to get a special appliance spray paint at a building supply store or large ... | |
| Harvest Maid Dehydrator | 10/1/2009 |
| Q: I have a Harvest Maid Dehydrator FD1000 model and it has stopped heating. I have read your other ... A: It is a special heat temp fuse. It is about 1/2" long and 1/8" dia. It probably will have one wire ... | |
| Everstar electric stainless steel skillet polarized plug | 9/30/2009 |
| Q: I have an everstar electric stainless steel skillet and the polarized plug has been malfunctioning. ... A: If the problem is just in the plug that goes into the wall, you should be able to go to any hardware ... | |
| Kitchen Aid Blender Model KSB5OB4 | 9/28/2009 |
| Q: I believe the part I need is called the clutch. Can you tell me where I can get the part. thank ... A: I think I can get this part for a Kitchen Aid blender but would have to special order it. Please ... | |
| Dryer heating source, No heat issue | 9/24/2009 |
| Q: I am working on an electric whirlpool dryer m# LER4634DQ1 S# MS0809482. This unit operates on 240 ... A: I am not an expert on dryers as we only repair small appliances but the principals are the same. The ... | |
| EA-3601 Waffle Maker | 9/23/2009 |
| Q: I am running an estate sale for a friend and there is a Universal Landers Frary & Clark EA-3601 on ... A: These are worth what ever you can get as I have seen them go for $15 and for as much as $90. They ... | |
| Landers, Frary & Clark electric perculator? | 9/23/2009 |
| Q: I have a chrome/silver? 3-foot, 2 handled Landers, Frary & Clark "Universal" Perculator. It is ... A: If it has round prongs it probably is not as old as 1908. Most of the appliances from that era had ... | |
| New phone static after 14 years | 9/21/2009 |
| Q: We have had two lines for many years; last Monday one of them started having terrible static on all ... A: It sounds like you have done almost everything to find the problem. I also just had a static ... | |
| Hamilton Beach #33 | 9/20/2009 |
| Q: I need a pair of brushes and a brush cap for the above unit. Please let me know if there is a ... A: I think we can supply these but you will have to make the request directly to our email address: ... | |
| fridge quit | 9/20/2009 |
| Q: I have a 1yr old, refridgerator, it is a compact, but still quite large. Has a seperate ... A: There may be a reset on the compressor but you will have to get to the inside of the unit to tell. ... | |
| danby 1000w micro wave problem | 9/20/2009 |
| Q: we have a new(3 mos) danby signature model 1000w microwave.recently it has started not heating up no ... A: It sounds like you have a bad magnetron tube. This should still be under warranty if you can find a ... | |
| fridge quit | 9/20/2009 |
| Q: I have a 1yr old, refridgerator, it is a compact, but still quite large. Has a seperate ... A: If it will not turn on at all, there is a good chance that the circuit breaker in the trailer has ... | |
| I have a Panasonic NN-T888S microwave/convection oven | 9/17/2009 |
| Q: This microwave becomes dangerously hot inside when used. I received a serious burn on my arm from ... A: I have not heard of a microwave getting the outside lining hot unless there are holes in the lining ... | |
| Everstar slow cooker DSE-60 | 9/16/2009 |
| Q: I broke my crock insert and have been trying to find one. Any ideas on were I might get one. A: All of the Everstar line of applinaces is made in China and I have been trying to find a parts ... | |
| sunbeam mixmaster | 9/15/2009 |
| Q: with built in timer. I am trying to find out any info on it like year and model name, as well as ... A: The first run of this unit was Sept. 1985. I am sorry but manuals are not available from Sunbeam on ... | |
| Everstar power cord | 9/14/2009 |
| Q: I am in need of a replacement power cord for an Everstar electric skillet. Where can I purchase ... A: I am not familiar with the Everstar brand name but we do have generic cords that will fit on a lot ... | |
| GE Stand mixer vintage | 9/14/2009 |
| Q: I recently purchased a vintage GE stand mixer. It is a 3 beater mixer. The first time I turned it on ... A: You know when you get as old as I am you do tend to squeak and squeal a little and it sounds like we ... | |
| Adjustable Bed control switch | 9/13/2009 |
| Q: The "Head Down" function on my adjustable bed stopped working and I'm now sleeping as if I'm in a ... A: I would try to contact WW Grainger and see if they have a switch that will work for your ... | |
| GE hand mixer | 9/13/2009 |
| Q: I'm trying to figure out how old my GE hand mixer is it has a CAT # of 30M47 would like some help on ... A: There should be a date code stamped near where you located the Cat.#. It may look something like ... | |
| Small household appliances | 9/13/2009 |
| Q: Which small household appliance is still manufactured in North American? (i.e.assembled, created, ... A: Out of all of the appliance companies (over 25) that we represent, I can only name one that is still ... | |
| 1926 Universal Percolater | 9/13/2009 |
| Q: The pot heats up immediately and gets boiling hot, the problem is, it doesn't begin to percolate ... A: If the water is heating, the problem is probably in the stem or the element or both. Be sure that ... | |
| Flickering power indicator light. | 9/11/2009 |
| Q: My Hamilton-Beach Table Top Oven, model 31197R works fine,but recently the red power indicator light ... A: I do not know much about the new Hamilton Beach units as they are all made in China now but I can ... | |
| westinghouse roaster lid glass | 9/11/2009 |
| Q: I HAVE A WESTINGTONHOUSE ROASTER THAT WAS MY MOTHER-IN-LAWS THIS LAST WEEKEND THE KID GOT DROPPED ... A: You can go to any glass store that cuts its own glass and order a piece of tempered glass that will ... | |
| westinghouse roaster | 9/10/2009 |
| Q: I am looking to buy the electrical plug in cord for the old westinghouse roaster. A: If your unit has round posts we should be able to supply this. Please contact us at: ... | |
| hamilton beach mixer model g, 7 FM 92056 | 9/7/2009 |
| Q: We are looking for the bowl that fits the above model mixer. It was my mother-in-laws, and we have ... A: You are correct, it is a special bowl and has to fit in the rings on the turntable. It is also ... | |
| Sunbeam mixmaster # 11 | 9/6/2009 |
| Q: I have an old ?1950's? bullet shaped mixmaster. It stopped working just as it had finished mixing a ... A: Maybe. If the speed control switch has broken we may be able to rebuild it. It is not cheap as the ... | |
| Landers, Frary & Clark coffee pot | 9/4/2009 |
| Q: I have an old 1924 Corona style, Landers, Frary & Clark coffee pot and I am missing an electrical ... A: If the prongs on your coffee pot are round and not flat, I think we will be able to help you. Please ... | |
| Harvest Maid FD-500 probe | 9/4/2009 |
| Q: This was my Mother-in-laws dehydrator which I believe she bought used. I do not think she ever used ... A: We do not have any parts books for Harvest Maid as they do not have any dealers. Have you tried to ... | |
| Sunbeam skillet repair | 9/3/2009 |
| Q: Wayne, I have a 30 year old electric skillet that I love. The control is fine but the heating ... A: If the control was bad I could probably help you but if there is an open in the element you are out ... | |
| electrical cord concern on appliance | 9/2/2009 |
| Q: The three-pronged plug pulled out of the outlet, leaving behind the center prong (ground prong?). It ... A: I would go to your local hardware store and get a replacement three prong plug and install it on the ... | |
| microwave oven | 9/1/2009 |
| Q: After a severe storm I had a problem with my microwave.....it made a really awful sound when I ... A: It sounds like it got hit with lightning. If that is the case, I would be looking for a new unit as ... | |
| Sunbeam mixmaster beaters jammed | 8/29/2009 |
| Q: Help! I have a decades-old Mixmaster that's always worked great... until the day I went to pop the ... A: I do not know what model mixer that you have but you probably have either a split case model or a ... | |
| microwave | 8/29/2009 |
| Q: I own a danby over-the-range microwave exhust, I believe there may have been foil used in it and it ... A: Most of the time the mag tube burns out and it may be cheaper to replace the unit rather than repair ... | |
| Hamilton Beach 30 mixer brushes | 8/28/2009 |
| Q: Can you get the brushes and one plastic cap for the model 30. If so I would like to purchase the two ... A: I think we have brushes for this mixer but I am not sure about the cap. If you will send this ... | |
| Mixer Capacitor | 8/28/2009 |
| Q: I was doing some research in trying to repair the speed control on a Sears "Deluxe Governor ... A: If the capacitor is shorted internally it will show as 0 resistance. If it is good it will bounce ... | |
| Mixer Capacitor | 8/28/2009 |
| Q: I was doing some research in trying to repair the speed control on a Sears "Deluxe Governor ... A: Your old Sears mixer was probably either made by Sunbeam or Hamilton Beach. You have probably ... | |
| Sunbeam Waffle Iron - wiring scheme | 8/28/2009 |
| Q: Wayne, I took apart and old Sunbeam Waffle Iron (Model W-2) and cleaned it up to original appearance ... A: The hot lead from the cord goes to one side of the thermostat. The other side of the thermostat ... | |
| Sunbeam Mixmaster #9 PTU unit | 8/25/2009 |
| Q: I wish to find and purchase a Power Transfer Unit(PTU) to fit my Sunbeam Mixmaster No. 9 stand ... A: I checked all of our books today and did not even find a reference to the meat grinder attachment. ... | |
| GE microwave JVM1440BH04 | 8/23/2009 |
| Q: My microwave is starting and stopping by itself at random times. Nothing has been programmed to ... A: It sounds to me like the main control circuit board is malfunctioning. When you unplug the unit for ... | |
| Philips mixer KB 5102 | 8/22/2009 |
| Q: Picked one of these at a garage sale (free) says patent 1938. Works great but, for future any idea ... A: We do not have any parts books for this unit but if you will measure the old brushes and contact us ... | |
| Sunbeam Mixmaster Vista Glass Bowl Replacement | 8/21/2009 |
| Q: I have a Sunbeam Mixmaster "Vista" model purchased around 1966. I need to replace the large white ... A: I may have something that will work on your machine but it will be used as they have not made white ... | |
| Sunbeam T-9 Toaster | 8/18/2009 |
| Q: Just acquired this model but when in cycle it gets to point of needing to shut off, elevate toast it ... A: It could be just an adjustment or the main thermostat could be malfunctioning. There are two ... | |
| Microwave Oven | 8/17/2009 |
| Q: RE: Fridgedaire Micro Wave, serial # 7G44104788 FMV 156DCA The fan motor quit. I need to know who ... A: The yellow pages are your best source for a repair shop that would repair this unit in your area. ... | |
| Delonghi bco70 | 8/17/2009 |
| Q: I need to replace the fuse can you tell me what it looks like and where it is located? A: We do not service Delonghi as parts are very difficult to get. Therefore we do not have any diagrams ... | |
| mixer turntable | 8/15/2009 |
| Q: Red Sunbeam MixMaster high power. Motor and mixers come on and turn. Turntable no longer turns. ... A: This mixer should be under warranty. You have two methods of finding out the warranty period. Go to ... | |
| Cuisinart GC-2000 Coffee Maker | 8/15/2009 |
| Q: My coffee maker is a 12- cup on demand maker and is about 6 months old. I woke up this morning and ... A: If you can find someone in your area that is a service center for Cuisinart, I would contact them as ... | |
| Vibrating disposal | 8/14/2009 |
| Q: We've had a top-of-the line, professionally installed garbage disposal for about three years. It ... A: We do not service disposals so my knowledge is very limited on them. All they are is a disc that ... | |
| gfci plug replacement | 8/14/2009 |
| Q: i am trying to replace a gfci plug on a curling iron. i was not able to locate a replacement, so i ... A: It will be the same on both units as one will be the hot and the other the neutral, they just do not ... | |
| Household fan repair | 8/14/2009 |
| Q: How do I remove the ossilating knob from the back of a normal household table fan? I want to take ... A: It seems like there are at least three different ways that they attach these knobs, maybe more. ... | |
| Haier 65 pint Dehumiifier | 8/13/2009 |
| Q: My dehumidifier is only a couple of years old, It had been running fine in the basement, I went down ... A: You have one of two problems. Either the GFI is getting weak or you have a compressor problem. Plug ... | |
| Signal Electric Fan Model 1251 | 8/13/2009 |
| Q: Found this hidden in attic of old house, I know nothing about this and can't find any imfo on line. ... A: I do not know much about old fans but if you will call Bill, 608-643-3616, he will probably be able ... | |
| Microwave oven | 8/11/2009 |
| Q: Is there a difference in an RV Microwave Oven and a "regular" susie homemaker Microwave oven? Can I ... A: Some RV's use the DC system in the RV and others use a converter to 120 VAC. Find out what you have ... | |
| Everstar Under counter ice maker | 8/10/2009 |
| Q: The machine makes ice. Also there is a lot of water in the bin as well. what could be wrong? A: I have been getting a lot of questions about these machines but we have not seen one in our shop ... | |
| CRAFTSMAN AIR COMPRESSOR | 8/10/2009 |
| Q: I have a Craftsman Compressor model 919.177541 (4HP Motor. 230 Volt / SINGLE PHASE) CAN I WIRE IT ... A: If you take the plate off of the motor where the wires are attached, it should have a wiring diagram ... | |
| Programming a garage door remote | 8/10/2009 |
| Q: I just moved into a new home and can not for the life of me get my vehicle to accept the garage door ... A: This is one area where I do not have much working knowledge. It seems like these things have a mind ... | |
| oster drink Blender | 8/10/2009 |
| Q: Got an old Oster model 40 Drink Mixer . A chrome beehive ?? It sparked its Plug and stoped working ... A: If you opened it and you can see that the switch is bad we may be able to help you out. If you can ... | |
| turntable on sharp microwave | 8/8/2009 |
| Q: The turntable is not turning. The microwave is working but turntable is not moving. What does it ... A: Some units use a belt drive to a motor and some use a direct drive motor. You will have to take the ... | |
| Harvest Maid Food Dehydrator | 8/7/2009 |
| Q: My fifteen or so year old Harvest Maid Companion Dehydrator Professional Model #1006P, Serial ... A: I have had this question before and I have not found a source for parts for this brand. If you can ... | |
| Microwave oven | 8/6/2009 |
| Q: I have a Sharp Carousel microwave oven. A couple of months ago the touch pad started not showing all ... A: Once the touch board starts to go there is really only one way to repair it and that is to replace ... | |
| Sunbeam Mixmaster | 8/5/2009 |
| Q: Mr. Keifer~ My Mom gave me her Sunbeam Model 7B Automatic Mixmaster. To operate the mixer I had to ... A: If a mixer runs at high speed only, it usually means that the capacitor is burned out. And if the ... | |
| cleaning fan blades | 8/4/2009 |
| Q: I am trying to clean my oscillating table fan blades. I took the screen off and on the blade is ... A: Most fans have a left handed nut on them to hold the blade in place. So the old "lefty ... | |
| nesco jet stream oven | 8/4/2009 |
| Q: How can I change the belt on a jet stream oven? I believe this is the reason for it not working. A: I am sorry but I checked with my repair techs and none of them has ever worked on a Nesco jet stream ... | |
| H B jar or blades for 902 bar mixer | 8/4/2009 |
| Q: I have a 902 and need new blades or new jar that will fit if not avilable.thank you. A: We should be able to help you with this request if you will contact us at: info@kieferappliance.com ... | |
| Black and Decker SM-100 Mixer | 8/3/2009 |
| Q: Yesterday, I cleaned my SM-100 Type 1 mixer with Fantastik spray after a messy mix. I didn't dunk ... A: We do not have any books for Black and Decker appliances so I can not help you but there is a ... | |
| Iron Horse compressor fails to run | 8/3/2009 |
| Q: I have an 5.3 Iron Horse model IH653036L compressor that seems to make a connection when the switch ... A: We do not service Iron Horse brand so I am only guessing at this point. Take the belt off of the ... | |
| Vintage Electric Fan | 8/1/2009 |
| Q: I have this great old GE oscillating electric fan with brass blades. A couple of the blades are out ... A: If the blades are bent, you can take the blade off of the fan and lay it on a table. Bend the ... | |
| LG Dehumidifier | 7/31/2009 |
| Q: I have a LG Dehumidifier (45 pint). Last winter the coils froze due to running it in my basement at ... A: This unit is a made in China special and therefore you probably will not find any parts for it. It ... | |
| Rice cooker | 7/30/2009 |
| Q: I would like to ask if there is actuator in conventional rice cooker? Thank you in advance. A: I am not familier with an actuator in any rice cooker that we have worked on. There is a thermostat ... | |
| Kitchenaid K45SS mixer. | 7/29/2009 |
| Q: I was using my mixer when a cloud of white smoke came out from the back of the machine and then it ... A: Usually it is not the motor that goes bad. I would guess that the circuit board in the rear of the ... | |
| osterizer blender, removing motor | 7/28/2009 |
| Q: HOW TO REMOVE Osterizer Blender Motor Drive Stud A: You have to hold the armature so it will not move. Sometimes you can get lucky if you place ... | |
| GE XL 1800 | 7/27/2009 |
| Q: My microwave keeps blowing 15 amp fuses. I've replaced several times. In the past it's worked for ... A: Something, probably in the high voltage circuit, is drawing way too much power. I would guess that ... | |
| sunbeam mixer | 7/27/2009 |
| Q: I have A Sunbeam mixmaster powr plus with A light and it works however I am not sure how old it is ... A: There should be a date code stamped on the unit. Check close to where the cat# was found. It is a ... | |
| Feedback | 7/25/2009 |
| Q: My Kitchenaid Blender (just over a year old), KSB560WH0, is bound up and I cannot remove the "jar". ... A: Kitchenaid blenders have a problem with the drivers that are attached to the motor. They are made ... | |
| Panasonic Microwave oven | 7/24/2009 |
| Q: I ma planning to buy Panasonic microwave oven model NNSD978S, 2.2 cft, 1250 watts. It has knob ... A: If the knob controls the timer, it probably has a separate timer as opposed to having the timer ... | |
| Blender bush-bearing worn out | 7/23/2009 |
| Q: My Blender's bush bearing that used to couple the blender jar to the motor base got burnt out when ... A: If you are from the UK I do not think I will be able to help you unless you have an Oster,Krups or ... | |
| Sunbeam delux glass Blender | 7/23/2009 |
| Q: I have the above appliance - Model SGB 150. The glass jug cracked when I put hot water in it. ... A: I am not finding this model on the sunbeam web site. It must be a very old unit. I think I can ... | |
| sunbeam mixmaster model 12 | 7/22/2009 |
| Q: How do I take this mixer apart? It is squealing when turned on. A: They usually squeal when the motor bearings are very dry. This may require disassembly of the ... | |
| Dormeyer 4200 beaters 'n bowls | 7/21/2009 |
| Q: We have recently bought a Dormeyer 4200 mixer. Love it; built with such quality. Can you direct us ... A: Dormeyer was by far the highest quality mixer on the market. That was their downfall. They lasted ... | |
| electric motor | 7/19/2009 |
| Q: problem is with a Kirby Generation 3 motor which should apply to motors in general. Just replaced ... A: It could be the armature but my money would be on the field coil. That is what usually causes the ... | |
| sunbeam mixer | 7/18/2009 |
| Q: I have A Sunbeam mixmaster powr plus with A light and it works however I am not sure how old it is ... A: This is an obsolete model on the Sunbeam web site. I can look it up in my old books at the shop but ... | |
| Farberware 12 Cup Percolator, Bronx Made Model LI 142B | 7/17/2009 |
| Q: Wayne, I am looking to replace the thermostat, but I have a question as to the main seal which goes ... A: It does not make any difference on the gasket. Always clean both serfaces. We usually use a thin ... | |
| Hamilton Beach drink mixer | 7/16/2009 |
| Q: I have an antique hamilton beach drink mixer and the agitator has separated from the shaft. How can ... A: On most of these mixers, the top agitator is just a press fit on the shaft that is tapered. If you ... | |
| 1984 JC Penny Microwave Oven Shutdown | 7/15/2009 |
| Q: . . Yesterday as I was defrosting some meat in the microwave it simply shut off including the ... A: It sounds like it may be a fuse if the whole unit turned off. The case will have to be removed and ... | |
| Griddle parts | 7/15/2009 |
| Q: I have an older JCP griddle that the probe has burned out. The probe number is #1209. Do you know ... A: We have generic probes that should work. They go up to 450 degrees. we do have to know the distance ... | |
| repair Chi hair straightener | 7/14/2009 |
| Q: the power cord for our Chi hair straigtener has a nick in it and causes the item not to work often. ... A: You should be able to replace the cord if you can get the unit open. Many of the new appliances are ... | |
| sunbeam mixmaster MMA | 7/13/2009 |
| Q: Wayne, I am trying to find out if this particular model of mixmaster has a dough hook and if yes, ... A: They did make them but did not come with the mixers new so there are not many around. They had to be ... | |
| Mixmaster parts | 7/13/2009 |
| Q: I have an old mixmaster shake maker with the 5 "stations". It is from the 50's- the mint green ones. ... A: I do not think that you will find any. They have not been made since the 1950's. It would be just ... | |
| ice maker | 7/11/2009 |
| Q: I have a undercounter ice maker that has a switch that says off,ice,and wash.When you hit the ice ... A: It sounds like the main control pc board is bad in the unit. We do not repair these units so I am ... | |
| Sunbeam mixer base | 7/11/2009 |
| Q: We have a Sunbeam mixer Model 2366-015 on which the stand is cracked. I found one site that showed ... A: I have checked our Sunbeam dealer web site and you are correct in that they do not sell the stand. ... | |
| hamilton beach scovill drink master | 7/11/2009 |
| Q: I picked up a mixer at a garage sale. it ia a"Hamilton Beach scovill drink master model 727al ... A: I am not sure when the 727 was made but if it has a picture of Micky Rooney it was probably made in ... | |
| saeco capuccino espresso maker | 7/11/2009 |
| Q: i use my saeco every day to make coffee. i do descale it every six months and i do use brita water ... A: I do not know where you are located but once every six months is not enough to keep the unit clean. ... | |
| dormeyer food fixer mixer model 4200 | 7/11/2009 |
| Q: I am needing a replacement plug for vintage mixer. Where can I obtain one. Thanks A: We usually do not replace only the plug on an old mixer. We always replace the cord with a grounded ... | |
| Sunbeam Mixmaster #01266 | 7/10/2009 |
| Q: I see you had someone post a picture of a mixer that looks just like the one I am trying to find ... A: Yes. To order you can email us at: info@kieferappliance.com We will email back with the exact cost ... | |
| 4 cup Farberware Percolator | 7/10/2009 |
| Q: I repaired this Farberware 4 cup percolator by removing(bypassing) a component in series with the ... A: It is about 1/4" long and 1/8" dia. with a wire lead coming out of each end of the fuse. They are ... | |
| toaster element wire | 7/9/2009 |
| Q: Where can I buy toaster element wire for a Breville ikon toaster? A: This is not a brand that I have seen. If it is an expensive brand you may find that the company ... | |
| Manual for FD200 HM Food Dehydrator | 7/9/2009 |
| Q: I am looking for a manual for an FD200 Harvest Maid Food Dehydrator. This dehydrator was given to ... A: I do not have any manuals for dehydrators. Your best bet is to go a store that sell new units and ... | |
| 4 cup Farberware Percolator | 7/9/2009 |
| Q: I repaired this Farberware 4 cup percolator by removing(bypassing) a component in series with the ... A: You have removed the heat sensitive fuse that is a protection against overheating and fire. The ... | |
| Sunbeam Microwave Oven Model SMW1155 | 7/8/2009 |
| Q: My Sunbeam Microwave Oven Model SMW1155 is now about 5 years old. For the past couple of days its ... A: It could be a number of different problems but it sounds like you may have a problem in the high ... | |
| Dormeyer Electric Mixer Fuse | 7/4/2009 |
| Q: I have a Dormeyer Mixwell Model 5100. The cord had deteriorated and I was installing a replacement. ... A: I think you have broken the capacitor. It was placed in some older mixers to suppress noise in ... | |
| GE Smart water filter | 7/4/2009 |
| Q: I just turned on out GE smart water filter that is next to my kitchen sink and the water is barely ... A: I am not familier with this appliance so I am only guessing as to what the problem may be. If this ... | |
| Vintage toaster | 7/4/2009 |
| Q: My mother has a vintage toastmaster toaster that is in excellent shape but the old fabric wrapped ... A: We install new cords on toasters all the time. We always install an HPN heat cord and it will be ... | |
| Sunbeam Mixmaster # 1-7A | 7/4/2009 |
| Q: Do you know if the Sunbeam Mixmaster 1-7A had a juicer attachment? And if so, what is the part #? ... A: I just happened to list one yesterday on Ebay under "Sunbeam Mixer Juicer Attachment" I listed it ... | |
| Fuse wheel | 7/4/2009 |
| Q: Where can I locate a replacement fuse wheel for an antique Farberware perculator no. 206? A: These have not been available for many years. We have substituted the new style fuses but it takes ... | |
| Hamilton Beach Model K Mixer | 7/2/2009 |
| Q: Recently inherited this Hamilton Beach Model K Mixer. How do you get the beaters to "latch"? Just ... A: I am not sure what the beaters look like for the model K but if they are attached together with a ... | |
| Oster Kitchen Center | 7/2/2009 |
| Q: My oster kitchen center will only run on #4 speed. Is there anyway this can be fixed as I like the ... A: If it is an electronic speed control with a circuit board, we are all out of the circuit boards to ... | |
| Sunbeam Mixmaster | 6/27/2009 |
| Q: Can you replace the plastic dial on the back of the mixer body. The mixer was recently shipped to ... A: I think so but we will require the model or service # from your mixer. Please request this part ... | |
| DSE-69 Crock Pot, pot | 6/26/2009 |
| Q: I am looking for the pot for my Everstar DSE-60 Crock Pot? Where might I purchase this part? A: We do not deal with the Everstar Co. so I do not have a parts contact. I would bet that if you look ... | |
| 3 speed cieling fan with capicitor (lasko) | 6/24/2009 |
| Q: there are 3 wires coming out of the capacitor yellow,black and red.they look like 16 ga.and are ... A: My only experience with ceiling fans is that I have installed a few. All I can tell you is that red ... | |
| Dormeyer Mixer Attachments | 6/23/2009 |
| Q: I have a Dormeyer Mixer 4300 in perfectly working conditions. However, the attachment for the meat ... A: We service very few Dormeyer mixers any more as they were discontinued over 25 years ago. The only ... | |
| George Foreman GV5 Roaster | 6/22/2009 |
| Q: My fairly new George Foreman GV5 Roaster is dead. It was roasting a chicken and it just shut down. ... A: Most of the time these "made in China specials" use, what they call "tamper-proof screws". You have ... | |
| George Foreman GV5 Roaster | 6/21/2009 |
| Q: My fairly new George Foreman GV5 Roaster is dead. It was roasting a chicken and it just shut down. ... A: There is a fuse in some of these models but not all. There is also a circuit board that can go out. ... | |
| Proctor Silex coffee maker | 6/20/2009 |
| Q: Is there a way to turn off the 2 hour shut off our Proctor Silex coffee pot? A: You should read the manual that came with the unit to be sure but I do not think you can extend the ... | |
| Hamilton Beach Scovill Model No. 25 | 6/19/2009 |
| Q: I have a nice steel Scovill/Hamilton Beach solid state mixer. It says it's a model 25, and 175 ... A: Hamilton Beach used a lettering system for their model #s on their older models up to about sometime ... | |
| Owners manual | 6/15/2009 |
| Q: I inherited a Sunbeam Vista food processor about 4 yrs. ago from my Mom's estate. It works ... A: You will probably not find one except maybe on Ebay. I would go to a dept. store and see if you can ... | |
| Noisy Refridgerator | 6/14/2009 |
| Q: I can head the fridge turn on and off every 20 minutes from my room. Is there any way to put a timer ... A: It is turning on and off because the temp. in the cooling compartment is warming up and the ... | |
| ge over the stove microwave does not heat | 6/13/2009 |
| Q: we have a microwave GEProfile Spacemaker XL Microwave Oven Model JVM1660 that does not heat, the ... A: Most of the new units have a very good manual for installation so you should be able to install it ... | |
| Oster Kitchen Center | 6/13/2009 |
| Q: I have an Oster Kit. Cent. mixer. The last time I used it it was working fine. I got it out to use ... A: I can not tell from you description if the base unit will not turn on or is it the mixer arm that ... | |
| Oster 403 blender | 6/13/2009 |
| Q: This has a 1959 date on the armature. The motor stud sheared off. do you have any parts for this ... A: If it is a square drive we should be able to help you. Please go to our web site and fill out the ... | |
| switch for adjustable bed | 6/12/2009 |
| Q: My son (43) a quadriplegic with no speech has an adjustable bed with switches for head up/down, legs ... A: I do not know if I can be much help to you but I do know that microwave ovens use a low voltage ... | |
| sunbeam mixmaster 1-8at | 6/11/2009 |
| Q: I was using the mixer when it started to give off a burning smell that was strong and penetrating. ... A: What you have found is the capacitor. If you would like a replacement capacitor, we will be glad to ... | |
| Sunbeam 2366 Mixmaster Stand Mixer | 6/10/2009 |
| Q: One of the features is a mixer-release trigger. It is a gray metal piece and I wanted to know how to ... A: It probably broke some plastic on the stand inside the throat of the stand. You will have to ... | |
| Antique Percolater | 6/10/2009 |
| Q: I have the follwing item which need two repalcment parts. One is the electic cord. Information ... A: Does the coffee maker have round or flat terminals that the cord plugs into? If it has round, we ... | |
| Rangeaire Vent Hood | 6/9/2009 |
| Q: I am trying to help an elderly lady with no internet access. She is looking for pliable filter that ... A: You should be able to order generic filters to fit this unit. Just measure the old one and check on ... | |
| ceiling fan wiring | 6/8/2009 |
| Q: im installing my ceiling fan i understand wiring, my problem is 1. there is no ground which means i ... A: You should have a white and a black wire coming through the ceiling. Some old houses were wired with ... | |
| Sunbeam 20-3 AG | 6/8/2009 |
| Q: I have a Sunbeam 20-3 AG that I just got from my Grandmother, and it won't lower the toast anymore. ... A: We repair one of these every week and would be glad to look at your toaster. Please send it to us ... | |
| Central vacuum stops after couple of seconds. | 6/7/2009 |
| Q: My eureka central vaccume works fine when I use it for the first time. As soon as I stop it and move ... A: It sounds to me like you may have a momentary open at either the plug or at the head end. After a ... | |
| Dormeyer hand mixer | 6/7/2009 |
| Q: I recently purchased a pink one,the model is HM 7-1, it is real heavy and all speeds and the ... A: There are people that collect Dormeyer appliances and they may be able to help you. Dormeyer has ... | |
| replacement dough hooks for Hamilton Beach hand mixer | 6/5/2009 |
| Q: I purchased a model #62665N Hamilton Beaach hand mixer, and I would like to know where I can find ... A: If this is a new hand mixer, I do not think that dough hooks were ever available for it. The mixers ... | |
| GE Spacemaker XL1800 Microwave | 6/4/2009 |
| Q: Our microwave starts, but within a couple of seconds starts emitting a loud hum and blue ... A: If there are any chips in the paint on the inner cavity, it will spark. Also if there are food ... | |
| Waffle Iron Connectors | 6/4/2009 |
| Q: Wayne. The cord to my Vitantonia Premier waffle iron was severed in the cabinet lazy susan. I think ... A: If the cord has two female quick connect terminals on it we can supply a cord. If you will call us ... | |
| Oster Kitchen center parts | 6/4/2009 |
| Q: I have an old Oster food processor (bought in 1984): Oster Kitchen Center (model number 971-06A). It ... A: I think we have most of the parts that you are looking for and you may order them through our web ... | |
| Repalcement cord for Waffle Iron | 6/2/2009 |
| Q: Wayne. The cord to my Vitantonia Premier waffle iron was severed in the cabinet lazy susan. I think ... A: Yes, you will need an HPN heat cord on your waffle iron. I am not familiar with this brand so I do ... | |
| sunbeam t-20 toaster | 6/1/2009 |
| Q: There's a toaster on ebay sunbeam t-20, but it does not lift the toast back up. Is that a difficult ... A: We repair these all the time. Sometimes they are just an adjustment and sometimes the thermostats ... | |
| hamilton beach model 30 brushes | 6/1/2009 |
| Q: I have a Hamilton beach model 30 malt mixer. I need a brush, spring and cap. Thanks, Mike A: I have some of these on order from my supplier as we speak. It will probably be a week or two before ... | |
| Connecting wall lamps | 5/31/2009 |
| Q: We have an old house. I was trying to install some new lamps. Everything worked out pretty well but ... A: If you are discussing a wall switch, there should be two white wires that are tied together with a ... | |
| counter top ice maker | 5/31/2009 |
| Q: I have a Magic Chef counter top ice maker. Model #MCIM30TW, Serial # 070900481. It just quit ... A: I have had some questions lately about these machines but we have not seen them in our shop yet. ... | |
| sunbeam mixmaster model 9b | 5/31/2009 |
| Q: i finally found beaters for my mixmaster, and i know it needs to be reoiled and the grease in the ... A: The model 7 and 9 should be almost identical. The oil that we use is Marvals Mistery oil or a good ... | |
| microwave features | 5/30/2009 |
| Q: Is the "simmer" feature the same as "warming" on microwaves?I want a unit that will do slow ... A: When a microwave heats it heats on full power. The way they control the intensity is to shorten the ... | |
| Repairing a battery compression spring.. | 5/30/2009 |
| Q: I have a baby swing. Inside the battery compartment are places for 4 c batteries. One of the ... A: This is the kind of thing that we run into every day. We are the only fix-it shop in about a 5 ... | |
| model d stand mixer | 5/29/2009 |
| Q: please help trying to find out how old this mixer is and how much its worth , i have a small bowel ... A: I assume that you have a Hamilton Beach model D mixer as this is the only one that I can think of ... | |
| Convection/microwave unit | 5/27/2009 |
| Q: The combo convection/microwave in our Winnebago RV sparks when I use the convection oven mode and ... A: Some of these ovens use the microwave at the same time as the convection to cook fast and the ... | |
| Hamilton Beach mixer - model g | 5/27/2009 |
| Q: I was wondering if you may be able to tell me where I might pick up the stand which is bottom part ... A: Our web site is: www.kieferappliance.com Use the "info request form" on the first page. We will ... | |
| Hamilton Beach mixer - model g | 5/26/2009 |
| Q: I was wondering if you may be able to tell me where I might pick up the stand which is bottom part ... A: This is your lucky day. We have both of the units that you need. I have the complete juicer ... | |
| Microwave Oven, Frigidaire Over the Range | 5/24/2009 |
| Q: We have a 9 year old microwave that recently stop working. I does not warm or heat water or food at ... A: The magnatron tube is usually the problem on an old microwave. It could be a diode or transformer ... | |
| sunbeam mixer 12C | 5/24/2009 |
| Q: My mixer still comes on but it wasn't working. My husband took it apart to clean on the advice of ... A: The resistor is the ceramic coated part that is about 1 1/2" long and the capacitor is the same size ... | |
| Bowl for oster regency controled power kitchen center | 5/16/2009 |
| Q: I own the kitchen center for a long time, but the large glass bowl broke. Where can one buy a new ... A: Yes, they will fit all older Sunbeam mixers as well, excluding the later models that have the bowl ... | |
| Small kitchen appliance ? | 5/15/2009 |
| Q: I have an object I thought was a waffle iron, but the interior is flat, more like a grill with a ... A: We have repaired some of these units. Universal was purchased by GE in the 1960's and GE appliances ... | |
| applianc thermostats | 5/9/2009 |
| Q: I need to find a thermostat to make a liquid warming plate. Ideally it could be set to 60 degrees C ... A: Sorry, but the lowest temp. I have is 112 degrees C. You may find an old food dehydrator with a ... | |
| Melitta coffee urn dispenser valve | 5/6/2009 |
| Q: I have a 30-cup Melitta coffee urn. It suddenly stopped dispensing coffee when I push the dispenser ... A: We do not service the Melitta brand so I do not know what it looks like but if the unit has a faucet ... | |
| Sunbeam Mixmaster Grinder attachment | 5/5/2009 |
| Q: I have a great old Sunbeam, where the beaters attach it says service #1-7A so I assume it is a model ... A: I think you may have the wrong attachment. The older models such as the #7, 8 and 9 and #10, 11 and ... | |
| Ge Steam Iron and Sunbeam Mixmaster | 5/5/2009 |
| Q: I have a GE Auto Shut-off Lightweight iron that will not heat. The light comes on that is on the ... A: The GE iron probably has a circuit board that is not working and there are no parts available. If ... | |
| sunbeamT20B toaster | 5/4/2009 |
| Q: my toaster has a small problem.it works fine except for not shutting off and ejecting the toast.all ... A: This is a thermostat problem and sometimes we can adjust it back into working condition and ... | |
| sunbeam toaster T20B | 5/3/2009 |
| Q: wayne,my toaster works fine except for not responding to thermostat setting.(very well done ... A: We have had very good luck servicing these units but they are not easy to adjust. The basic charge ... | |
| Sunbeam mixmaster 1-7A | 5/3/2009 |
| Q: I just bought a Sunbeam mixmaster 1-7A at a yard sale. I need a large bowl for it. Can I buy a ... A: This model was made for many years as it was one of the best models that Sunbeam made. They started ... | |
| Dominion Waffle Iron Model #1218A | 5/3/2009 |
| Q: I do not know how old the waffle iron is but it has one handle missing. Do you know where I might ... A: You can use an oven cleaner for the plates but once they are clean you will have to break them in ... | |
| Beaters for Dormeyer silver chef 4300 | 5/2/2009 |
| Q: Is it possible to obtain beaters for this lovely old machine? A: This is a very common model and so they were the first parts to sell out of. Your only hope is to ... | |
| Sunbeam Mix Master | 5/2/2009 |
| Q: I have a Sunbeam Mix Master Legacy Edition, Heritage Series, 12 speed, model 2346. I have only ... A: Parts are limited on this mixer as it was made in China. I did check the parts list and there are ... | |
| T-35 Sunbeam Radiant Toaster burning toast | 5/1/2009 |
| Q: Our T-35 Sunbam Radiant toaster lowers the bread just fine but burns every piece of bread. The ... A: We can probably repair your toaster. If the thermostat is welded, we are out of luck because no ... | |
| thermostat control | 5/1/2009 |
| Q: I have a Rival Chef's Pot Multi-Cooker Model #22006 and the thermostat control just died. Rival does ... A: We are not a Rival dealer any more so I do not know what control they are using now. We do have two ... | |
| leaking rowenta de 871 a iron | 4/30/2009 |
| Q: In both dry and steam modes, the iron discharges water on the clothes. It has not been overfilled ... A: I think that you will find that the sole plate is not getting hot enough to create steam and water ... | |
| microwave heating on/off | 4/29/2009 |
| Q: Whirlpool microwave/hood combo...heats intermitantly.can hear clicking noise back of control panel ... A: The only thing that you can do is replace the circuit board and I can not say for certain that that ... | |
| Sunbeam Vista Food Processor S Blade | 4/29/2009 |
| Q: I found a Sunbeam Vista Professional Food Processor in my folks basement. It has all of the parts ... A: Sorry but every company has their own design for these so they are not interchangeable. If you will ... | |
| Dominion Waffle Iron Model #1218A | 4/27/2009 |
| Q: I do not know how old the waffle iron is but it has one handle missing. Do you know where I might ... A: I have some old handles that I keep just for this type of application. If you can take a picture of ... | |
| Dormeyer Power Chef Model SM 12 CH | 4/27/2009 |
| Q: I am attempting to locate a beater for this model will the Sunbeam Item# OS-MMB function as they are ... A: I am sorry but I do not know of any replacement for your Dormeyer beater. It seems like every ... | |
| Coffee Maker Carafe | 4/26/2009 |
| Q: Just curios...... Did you ever find a replacement carafe for your Everlast coffee maker? I cracked ... A: We have not seen this brand name in our area but I do have a generic company that sells carafes for ... | |
| mixette mixer | 4/26/2009 |
| Q: I have a mixette mixer model # 51 fm and trying to find out how old it is.. as I inherited it about ... A: You do not say if "mixette" is a brand name or a model of a Sunbeam mixer. It sounds like a Sunbeam ... | |
| anitque electric floor clock | 4/26/2009 |
| Q: I have an old electric floor clock, with 4 shelves in the lower part. The face says "Jackson ... A: I would have to see the actual motor assembly before I can say that I can replace the motor. Many ... | |
| Sunbeam Mixmaster Blades Hit Each Other | 4/22/2009 |
| Q: Our Sunbeam heritage mixmaster blades hit each other running at all speeds. Is there an adjustment ... A: You probably have one of two possible problems. One, sometimes the plastic drives on the beaters ... | |
| Coffee make owners manual | 4/21/2009 |
| Q: I have a Everstar Programmable Coffee Maker features LED Display Timer, 12 cup capacity and ... A: We do not service Everstar but I would go back to the store that you purchased it from and request ... | |
| Rowenta DE-871 steam iron | 4/19/2009 |
| Q: The plate is loose. I have taken the special screw off the back but can't figure how to take it ... A: From looking at the parts diagram, I would say that you have to remove the whole top of the iron in ... | |
| Oster Kitchen Center part needed | 4/19/2009 |
| Q: I am looking for the screw-in knob that holds the meat grinder onto the mixer arm. I don't have a ... A: We may have a used one of these but you will have to request it through our web site: ... | |
| Sunbeam Mixmaster | 4/17/2009 |
| Q: Can't get one of the beaters to insert. It has been reluctant for a year or so, but now is adamant ... A: If it is an older model with the small snap ring that holds it into the mixer, you may have to ... | |
| Using aan American hotpot or coffee maker in Europe | 4/16/2009 |
| Q: I have a one cup drip coffeemaker marked "120V~60Hz 300 W." Is it safe to use in Europe and UK with ... A: Most of the hotels in the UK and Europe have sockets for 120 Volt appliances and you should not even ... | |
| wall phone jack which wiress go where. | 4/16/2009 |
| Q: i bought the GE WALL JACK PHONE MOUNT TL26294. I TOOK OUT THE OLD ONE. the box got torn and i ... A: Look at the color of the wires in the phone cord and match them with the colors on the phone mount. ... | |
| oster kitchen center | 4/15/2009 |
| Q: this is my 2nd request for a response. I own an Oster Kitchen Center. The speed control is ... A: Sorry, I did not receive your first request. Sorry but we ran out of these speed controls about 6 ... | |
| electric blanket control | 4/14/2009 |
| Q: the control on my electric blanket flashes f2 and the control does not work. is there a way to ... A: The only fix to this problem is to replace the control unit and I am not sure if they are available. ... | |
| black & decker portable electric can opener | 4/13/2009 |
| Q: I broke the contact off the wire that attaches the battery to the body of the can opener called ... A: If you have a radio/TV repair shop in your area, you may get them to solder it back for you. I do ... | |
| Bowl Will Not Spin | 4/13/2009 |
| Q: My Sunbeam MMA mixer was stored for several years following a move. I vaguely remember a small ... A: Is it the bearing assembly that you are missing? If it fell out of the unit the bearings are gone. ... | |
| Westinghouse Roaster oven #RO 5411 | 4/11/2009 |
| Q: I have a Westinghouse roaster oven model RO 5411, the temp indicator light built into the dial won't ... A: Most of these were not a bulb but a small heating element. When it glows they had a small glass so ... | |
| Sunbeam Vista Mixmaster | 4/11/2009 |
| Q: I have been given an old but great running Sunbeam Vista Mixmaster Power Plus on the bottom it has a ... A: We will probably have new beaters in stock for what ever model you have. The dough hooks are very ... | |
| Hamilton Beach Stand Mixer Model E | 4/10/2009 |
| Q: I'm just looking for a little information. I have an Old Hamilton Beach Stand Mixer Model E, Which ... A: This is a very good model mixer and should last for many years. It is hard to tell the exact year ... | |
| Meat grinder attachment | 4/8/2009 |
| Q: My aunt just recently got the sunbeam mixmaster model 2364 and has been asking me about meat grinder ... A: Please check the Sunbeam web site(sunbeam.com) first. If they have any attachments they will be ... | |
| sunbeam 2774 | 4/2/2009 |
| Q: I have a sunbeam 2774 kitchen assistant and the seal/gasket came off and got chewed up by the blade. ... A: Ashley, We do not have the part in stock, and Sunbeam has it on back order. The only way Sunbeam ... | |
| signal electric model J fan refurbing | 4/2/2009 |
| Q: This fan has been messed with before I got it,There are four wires besides the two for the brushes ... A: I am going to try to help but without seeing the fan it is not easy. This is only a guess on my ... | |
| Sunbeam T 20 B | 4/1/2009 |
| Q: Wayne, The activating bar that the bread pushs down does not seem to be working right, I took it ... A: This is not an easy fix. There is a delicate balance between two adjustments that has to be made. ... | |
| Salvage perfume in a malfunctioning perfume bottle | 4/1/2009 |
| Q: Someone gave me an expensive bottle of perfume. One day I dropped the bottle on the floor ... A: If the top unscrews, take it off and try to reattach the tube. If not and the bottle is plastic, ... | |
| wear ever crock pot | 4/1/2009 |
| Q: where can i find a replacement cord with hi and low control built into cord A: I am almost sure that this cord is no longer available. All of the new units have the temp. ... | |
| westinghouse countertop stove | 3/31/2009 |
| Q: I've broken the plate glass insert for the top of the appliance. This is probably a 1960's era ... A: There are a few web sites that specialize in obsolete appliance parts. You will have to do a search ... | |
| my everstar ice maker | 3/29/2009 |
| Q: my ice maker keeps beeping and i cant stop it i have clean it dont no what elese to do with it A: We do not service ice makers as that is a large appliance option on a refig. but I will take a guess ... | |
| Replacement bulb for 1940s Universal Waffel Iron | 3/29/2009 |
| Q: Any idea where I could purchase a replacement bulb for my waffel iron 1940s universal It is about 1 ... A: There are some companies on the web that specialize in obsolete electronic parts. I do not think ... | |
| Avanté Deluxe toaster sudden stop | 3/28/2009 |
| Q: I have waded through a lot of the prior Q&A's on toasters but can't find quite the right situation. ... A: I think you will find that there are no parts available for this Chinese made unit. Just like all ... | |
| Sunbeam Mixmasterz | 3/26/2009 |
| Q: Recently my mixer just stopped working in the middle of mixing a loaf recipe. No smell or noise to ... A: If it is this old, the switch probably has broken on the speed control. This is a problem with ... | |
| dehumidifier trips breaker | 3/25/2009 |
| Q: I have a Haier HD301-T dehumidifier. It has just started tripping the breaker. I unplugged the unit ... A: Typically what will happen is that the compressor is frozen up and is not moving. This overloads ... | |
| black and decker gizmo | 3/24/2009 |
| Q: Are there batteries available for the Gizmo mixer unit? model #GM200 it is a 2.4 volt nicad pack. A: There is only one source for B & D parts in the US. Try Fox International web site. If they do not ... | |
| Sunbeam T-20 toaster heating element | 3/24/2009 |
| Q: My beautiful toaster just popped a heating element in the center section right at the top screw ... A: You are correct. This is one of the best toasters ever made. We repair many of these units each ... | |
| DCC490SA coffee maker | 3/23/2009 |
| Q: The off/on switch works intermittently. Works normally for a few days, then won't turn on. Repeated ... A: I do not know what brand coffee maker you have but switches are mostly generic if they are not part ... | |
| panasonic microwave/convection oven dimension 4 the genius NE 9970 | 3/22/2009 |
| Q: When I press my auto sensor control for the microwave,the hot display in shown. The oven is not ... A: We are not a Panasonic service center so we do not have any manuals for any of their units. This is ... | |
| old General Electric Coffeemaker | 3/7/2009 |
| Q: I need a filter basket for a 32 year old GE immersible coffeemaker model p15/3315. Are they still ... A: Sorry, I have not had GE coffee maker parts for years. We did carry some Black and Decker parts ... | |
| whirlpool over the counter microwave | 3/7/2009 |
| Q: Our microwave was bought about 2 years ago, after the previous one (also Whirlpool) was giving ... A: Yes, an electrical serge could have caused this problem. Either the touch panel or main circuit ... | |
| sunbeam mixer gears #2365 | 3/6/2009 |
| Q: I have the same question as bevs. I need two new gears that make the beaters turn do you have any ... A: The only way that we may have some is if we would have a warranty returned mixer that did not have ... | |
| Garbage Disposal | 3/4/2009 |
| Q: I have sinkmaster garbage disposal that I can't get out of the old sink,Is there some way that you ... A: There should be a ring just under the sink on the disposal that has to be turned to release the ... | |
| hamilton beach model 18 | 3/4/2009 |
| Q: I have a hamilton beach model 18 milkshake mixer. The enamel is in perfect condition. The chrome ... A: We could do what you ask but the cost would be prohibitive to rechrome such a small item. I would ... | |
| Tefal 8446-40 toaster | 3/3/2009 |
| Q: Concerning the above toaster: When toasting bread it will come up too soon. It is set at highest ... A: It probably has a thermostat that is getting weak and should be replaced. It is highly likly that ... | |
| hair dryer cord plug | 3/3/2009 |
| Q: Can you replace the GFI plug on the cord of a hair dryer. The plug has something rattling inside ... A: I have not found a supplier for this unit so we purchase the cheapest hair dryer we can find that ... | |
| singer sewing machine and transformers | 3/2/2009 |
| Q: I just purchased a Singer Tradition sewing machine in the US, so it is wired for 110-120. I plan ... A: If you will look on the sewing machine motor plate it should tell you how may watts that the motor ... | |
| model/model number /date | 3/2/2009 |
| Q: I have a green General Electric hand mixer I am trying to identify. The only information on this ... A: The cat. no. is the same as the model #. This is just the way that GE used to mark their ... | |
| Glass Cover | 3/1/2009 |
| Q: Need glass cover for a Crockery Chef Brand electric slow cooker. The diamter is 10 and 1/8 exactly ... A: We do have some new and used crock pot covers but I have to ask you to please send your request ... | |
| American Harvest/Nesco Jet Stream oven | 2/26/2009 |
| Q: I have an American Harvest/Nesco Jet Stream oven (countertop convection oven). It needed a new belt ... A: If you can replace the capacitor, you may not have another problem. I would try that first. But if ... | |
| Sunbeam mixer only runs slooooow | 2/23/2009 |
| Q: I recently got a hand-me-down Sunbeam Mixmaster. No model number on it anywhere, but it says its ... A: This is a very good Sunbeam mixer. We repair a lot of this model because Sunbeam made a lot of ... | |
| Sunbeam Mixmaster MMA Power Transfer Unit | 2/22/2009 |
| Q: What type of power transfer unit do I need for my Mixmaster Service NO MMA? I want to purchase the ... A: I would have to see the power unit but I believe that any power transfer unit that will fit into ... | |
| Small rotisserie oven | 2/22/2009 |
| Q: Please where can I find a small oven with a rotisserie like the old Molineaux Loving oven. I believe ... A: Sorry I do not. Ask the store or web site that is selling the unit if it is repairable and where to ... | |
| electric kettle | 2/20/2009 |
| Q: What uses more power to boil water? My electric stove with a pot of water (2-3 cups) or my electric ... A: Your stove top will draw a larger amount of power but will take a shorter amount of time to boil ... | |
| Bunn-o-matic pour over coffee maker | 2/20/2009 |
| Q: it's a three pot warmer,one up two bottom. I cleaned the unit out, reservoir tank, and heating ... A: I do not know much about Bunn coffee makers as Bunn does not have service centers and will not sell ... | |
| kitchen appliance | 2/19/2009 |
| Q: Our range hood works by filtering the air and returning it to the room. Is there any reason not to ... A: The only reason that I can think of is that the moisture may rot your roof boards. Almost all of ... | |
| Mixmaster 10A1 Disassembly | 2/18/2009 |
| Q: Wayne, I have a good running Mixmaster 10A1 but suspect the gear grease needs changing. I assume the ... A: Yes, there is a little cover in the center of the front piece with the handle on it that has to be ... | |
| Sunbeam 12C mixer | 2/17/2009 |
| Q: I am having a problem with the beaters staying engaged in the mixer. The two covers over the ares ... A: It sounds like there is either a problem with your beaters or the inner workings of the beater ... | |
| arching microwave | 2/14/2009 |
| Q: My microwave has begun to arch for no apparent reason. Can this be repaired? A: If the arcing is taking place inside the cavity you probably have some spots inside where the paint ... | |
| GE Spacemaker microwave has grinding noise | 2/14/2009 |
| Q: We have a two-year-old (no warranty now) GE Spacemaker microwave, model JMV1870 that has just ... A: The olny thing I know of that can cause a grinding sound would be the motor that operates the ... | |
| Dormeyer Mixer Beaters | 2/13/2009 |
| Q: I have a vintage Silver Chef Model 4300. Am looking for a pair (or even just 1) replacement beater. ... A: We do have some new beaters for Dormeyer mixers but I do not have anything that will tell me what ... | |
| Oven light, GE Combo oven | 2/12/2009 |
| Q: GE combination microwave/convection, Model JE1 1590SC 001. The oven light went out. How do I replace ... A: I just found a set of screw driver bits that will remove all of these type of tamper proof screws at ... | |
| KitchenAid K5SS 325 watts | 2/11/2009 |
| Q: This is a very nice mixer passed on by deceased relative. It sat a while unused and inner became ... A: There is no interior fuse in these units. There are some circuit boards that govern the speeds that ... | |
| Sunbeam mixer model 11 | 2/10/2009 |
| Q: I have taken the front of the mixer off to clean and re-grease the gears. I woild like to take the ... A: Remember these gears have not been moved for many years and they are tight. You may have to drive ... | |
| KitchenAid K5SS 325 watts | 2/10/2009 |
| Q: This is a very nice mixer passed on by deceased relative. It sat a while unused and inner became ... A: I would not recommend a full disassembly as you may not be able to get it back together. It sounds ... | |
| PanasonicMicrowave Convention Oven | 2/9/2009 |
| Q: I have an old Panasonic Microwave Convention Oven NE-9970 700 watts. It is or was a great unit. Now ... A: A 700 watt unit is small for todays standards. I think it is time for a new one. Most of the new ... | |
| rowenta steam irons (2) | 2/9/2009 |
| Q: I have a rowenta steam iron DE880 auto shut off, no heat at all to sole plate. in park position ... A: The cost of any Rowenta parts make it not worth repairing them. It sounds like you may require a ... | |
| Hoover blender | 2/7/2009 |
| Q: Wayne I have a Hoover blender approx 40 years old. Base motor is good, still works. The cup was ... A: Let me know if the base is round and if so what is the diameter. If it is round, I may have ... | |
| GE spacesaver microwve | 2/7/2009 |
| Q: How do I replace the handle on my microwave? A: We are not a GE dealer so we do not have any books on specific models. You should be able to order ... | |
| Oster Regency Kitchen Center | 2/6/2009 |
| Q: How do you take apart the motor area? I can't locate directions. We tried to take it apart to ... A: How far did you take it apart? Did you take the motor out of the machine? It may help to go to our ... | |
| oster kitchen center mixer head | 2/5/2009 |
| Q: We have the same squealing problem in the mixer head. What part is needed to correct the problem? A: You may not require a new part. The mixer head must be disassembled and cleaned. Clean all of the ... | |
| Landers, Frary, & Clark | 2/4/2009 |
| Q: I have an old electric standing mixer that I can not find any information on, other than it is ... A: This is a really neat mixer. I have a Sunbeam Model #1 that is similar. The company that made this ... | |
| Whirlpool EC5100 XP Undercounter Icemaker. | 2/4/2009 |
| Q: I was given a Whirlpool EC5100 XP Undercounter Icemaker. I hooked it up a couple of days ago and ... A: I am sorry but my knowledge of this appliance does not exist. We do not repair them and I have ... | |
| Hamilton Beach stand mixer | 2/4/2009 |
| Q: I also have an Hamilton Beach Model D stand mixer. I was wondering if you knew what it is worth, and ... A: You best indication is see what they are selling for on Ebay. My guess is not too much. Sunbeam ... | |
| shop vac | 2/3/2009 |
| Q: I own a 5 gallon shop vac 1.5HP Sometimes the bearing squeal when I shut it off and was wondering if ... A: Most Shop Vac units use a sealed motor. See if there are screws that hold the case together. If so ... | |
| Seeking Quiet Blender | 2/3/2009 |
| Q: I am seeking a blender is quiet, but still gets the job done. My price range is $250 or less. Key ... A: I do not think that I have seen a quiet blender. They all have to rotate so fast that they just ... | |
| beaters | 2/3/2009 |
| Q: Do you have beaters for Dormeyer model 4200 Food Fixer? A: The 4200 was made with different beaters over the years. If you can take a picture of an old ... | |
| power cord | 1/30/2009 |
| Q: I have a Sunbeam counter top electric grill, Model- GPA3033. I am in need of the power ... A: I do not have a picture of your particular unit but I think I know what you are looking for. Does ... | |
| F. B. Rogers Silver plated Percolator | 1/29/2009 |
| Q: I purchased an F.B Rogers Silver plated percolator on ebay. It didn't have a cord or stem and ... A: I am somewhat familiar with that particular company but I do not know who made the unit for Rogers. ... | |
| mixer blades | 1/29/2009 |
| Q: I found a Montgomery Ward appliance mixer in my mother's shed it works but it has no mixer beaters ... A: Montgomery Ward never made any of the appliances that they sold. They were made usually by Sunbeam ... | |
| Oster kitchen center repair | 1/29/2009 |
| Q: I broke the drive gear on my Oster Kitchen center that I love dearly. We have the new gear OS-47908 ... A: I know Oster made very few of these 5500 models and you were very lucky to find a coupling. If you ... | |
| DeLonghi F885.SO drain hose replacement? | 1/28/2009 |
| Q: I've bought the spare hose, now I just need to fit it. Can anyone point me to a service manual or ... A: We are not a DeLonghi dealer so I do not have access to any manuals. I can not tell from your ... | |
| Rowenta Iron (Professional) Auto-Off Problem | 1/27/2009 |
| Q: Like other users, my Rowenta iron is difficult to restart once it has shut off (by the auto-off ... A: You are correct. This is not the iron for quilting. I sell an iron called the Black & Decker ... | |
| hot plate | 1/24/2009 |
| Q: I have a hot plate/buffet server that has an on/off switch that when turned to the right turns the ... A: It must be a rheostat switch. It will control the heat as well as turn the unit on and off. That ... | |
| microwave | 1/24/2009 |
| Q: emerson unit, it was working fine but i hit something and it start it counts down the time . it will ... A: First try to unplug the unit for at least five min. and see if it will reset. Sometimes the ... | |
| Hamilton Beach No. 33 Jade Milkshake Maker | 1/23/2009 |
| Q: Where can I find parts? I need bearings for the lower part of shaft and new brushes. Also, how do ... A: Good questions. First, there are only very limited used parts available and they are very hard to ... | |
| Sunbeam electric blanket | 1/22/2009 |
| Q: I purchased a queen blanket thru Land's End, really liked the performance, also in a couple of years ... A: The thermostats are getting weak in the blankets. The newer units are electronically controlled and ... | |
| Microwave problem | 1/22/2009 |
| Q: I have a GE Profile Spacemaker II microwave. Sometimes when I shut the door the microwave starts ... A: It sounds like you have a door switch problem. There are usually two or three door switches and one ... | |
| Westinghouse WF-4 Waffle Iron Question | 1/22/2009 |
| Q: Keifer, I see that you have repaired this type of waffle iron before from your other posts. I have ... A: It sounds like you do not have a thermostat in the unit. It relys on the size and length of the ... | |
| Westinghouse WF-4 Waffle Iron Question | 1/21/2009 |
| Q: Keifer, I see that you have repaired this type of waffle iron before from your other posts. I have ... A: If you are not going to keep the unit, it is not worth repairing. We get around $60 to rewire one ... | |
| Microwave Ovens | 1/21/2009 |
| Q: I have a 15+ year old microwave that still seems to be operating okay. My question is: Do microwaves ... A: The waves do not, but the mag tubes do get weaker and food cooks in more time than when new. The ... | |
| Delonghi Microwave problem | 1/19/2009 |
| Q: its hardly been used but is out of manufactures warranty.The microwave does not heat up at all, the ... A: If it will not heat at all your problem is not a simple one. I would guess that your problem is ... | |
| CO Detectors | 1/18/2009 |
| Q: We just moved an electric CO detector from a bedroom to livingroom and it won't quit beeping. We ... A: Do not question if it works or not. For the cost of a new detector it is not worth it. Just ... | |
| t-fal Avanti Convection / Toaster Oven | 1/17/2009 |
| Q: My t-fal Avanti toaster oven is totally dead. (I checked kitchen circuits and they're OK.) Tried ... A: There may be a fuse but it will probably be located on a circuit board and the whole board will have ... | |
| Oster toaster oven #4831 | 1/16/2009 |
| Q: Broke a timer dial knob on the little oven, unable to locate anyone on the internet that closely has ... A: If you go to the Sunbeam web site, they should tell you if you can order this part. If it is ... | |
| Sunbeam Mixmaster | 1/16/2009 |
| Q: I have a Sunbeam Mixmaster. It says model number 0138 on the bottom, so I think it considered a ... A: I am not sure what the mod. 0138 looks like but I think it is an older model that has a resistor ... | |
| Microwave convection heat | 1/16/2009 |
| Q: I have a Panasonic NN-T888S microwave/convection oven. The microwave works fine. The convection oven ... A: There is a separate thermostat that controls the convection oven circuit of the oven. It needs to ... | |
| Everstar Appliances...Under counter Ice maker, UB Wrong! | 1/15/2009 |
| Q: Problem with a full bin red led & shut off, isn't the control board,it's the bin sinsor.38 yrs. ... A: Sorry but we have not serviced any of these units. They must not sell them in the upper midwest. ... | |
| parts for hb model 25 mixer | 1/15/2009 |
| Q: i recently bought a old hamilton beach model 25 milk shake mixer and during shipment the 2 bolt ... A: We have repaired some of these brackets with a product called J B Weld. Take the motor loose from ... | |
| Chip on the inside of my microwave | 1/14/2009 |
| Q: My question is can I use Rustoleum appliance paint to cover the metal that is showing through? ... A: I think if you go to a local building center, they may carry a special appliance paint that you can ... | |
| Kitchen Aid Stand Mixer | 1/6/2009 |
| Q: I have a very old mixer (large crank-up kind) that was working well but needed a new cord. When the ... A: It depends on how old the unit is. Some of the very old Kitchenaid mixers had mechanical speed ... | |
| replacing microwave | 1/6/2009 |
| Q: want to replace ge spacemaker xl microwave oven JVM1340WW but I don't know what size I can replace ... A: Look at the lable usually found inside the door frame or on the back of the unit. It will give you ... | |
| Hamilton Beach Mixer Model G | 1/3/2009 |
| Q: I dropped a resident's Hamilton Beach mixer and broke the black handle right off.....Know where I ... A: Nancy, Sorry, but we are unable to get a handle for the Hamilton Beach Model G Mixer anymore, we ... | |
| electric coffee pot part | 1/3/2009 |
| Q: Where can I purchase a replacement glass top for my very old electric Royal-Matic Hi-Speed ... A: Ellen, We may have a replacement Fitz-All Percolator glass top for your percolator. We are going to ... | |
| Landers, Frary & Clark Universal antique percolator #E91816 | 1/2/2009 |
| Q: I am trying to locate a place to repair my percolator. It just stopped working. The cord checks ... A: You can send your percolator to us and we can take a look at it. Please include a note with your ... | |
| blue ice machine | 1/2/2009 |
| Q: i have recently purchased a blue ice machine from cosco and have lost my receipt. the problem is the ... A: We don't have any contact with this company, but if you look in the literature that came with the ... | |
| Dehumidifier problem | 1/1/2009 |
| Q: I have a room that varies in room temperature from 55 degrees to 80 degrees depending on the season. ... A: Most dehumidifiers will not operate under 70 degrees. You should not need one in the colder months ... | |
| Carbon brushes for Sunbeam Mixmaster model MMA | 1/1/2009 |
| Q: Kiefer, My Sunbeam Mixmaster model# MMA needs a new set of carbon motor brushes and a new speed ... A: We should be able to supply you with motor brushes and may have a used speed control handle. We do ... | |
| mixer | 12/29/2008 |
| Q: who can replace cord on old mixer A: We do it all the time. Just send us the mixer head only and we will gladly replace it for you. If ... | |
| sunbeam mixmaster | 12/28/2008 |
| Q: Why will my sunbeam mixmaster not tilt back? A: There are about 100 different Sunbeam mixer models and you do not identify which one you have but ... | |
| Oster toaster oven timer control | 12/28/2008 |
| Q: I have an Oster toaster oven, model #6238. When using the timer control, the oven will shut off when ... A: You definitely require a new timer. Please go to our web site and enter this model # and part ... | |
| NOMA Back-up Power System, 1,800W | 12/28/2008 |
| Q: I was looking at a power back-up unit to power my gas furnace when the power goes out,and was ... A: If you look at the motor on your furnace, it should have a wattage usage listed on the information ... | |
| crystal tip ice maker | 12/27/2008 |
| Q: Do you have any ideas where I might get an electrical schematic or repair manual for a large, ... A: We only service small appliances such as coffee makers and electric shavers so my knowledge is very ... | |
| Girmi PC53 | 12/25/2008 |
| Q: I have been using Girmi food steamer for last 3 years. While cleaning, I accidentally had some water ... A: My guess is that you got some water on the motor and it blew the fuse if it has one. If you have a ... | |
| Sunbeam Mixmaster Vista | 12/24/2008 |
| Q: I have a Sunbeam Vista Mixmaster unit, service # 8037BD, and the stand has broken, where the mixer ... A: I do not have access to Sunbeam parts books at this location so I would like to ask you to request ... | |
| B&D TRO1000-4000 series | 12/24/2008 |
| Q: Any suggestions? How do I take the side off? I might be able to fix it if I could figure that out! ... A: There are usually screws on the bottom that hold the side panels on. It has hooks on the top so you ... | |
| sunbeam mixer model# 2356 | 12/23/2008 |
| Q: Mixer quit working found out it is the circuit board but cannot find one anywhere...help A: We may have this part in stock. You will have to request it through our web site at: ... | |
| Mixer Problem | 12/22/2008 |
| Q: My SunbeamMaster Mixer Model #2366,beaters keep dropping out as if they are not clipping in the ... A: This is really a poor design of Sunbeam. This mixer was made very cheaply in China and they do have ... | |
| Mixer Problem | 12/22/2008 |
| Q: My SunbeamMaster Mixer Model #2366,beaters keep dropping out as if they are not clipping in the ... A: In order to replace the gears in your model mixer you have to replace the entire motor assembly and ... | |
| grease for 1955 sunbeam mixmaster 11 | 12/22/2008 |
| Q: I see you mention automotive grease for other brands of mixers, Can I use a lithium white grease in ... A: Usually when the motor turns very slowly the problem is usually the end bearings of the motor as ... | |
| mixmaster gears | 12/22/2008 |
| Q: I have a Sunbeam mixmaster heritage series model #2350 350 watt, the plastic gear going down to the ... A: Sorry to tell you this but you have to order the entire motor assembly just to get the gears. That ... | |
| Mixmaster MMA Replace Beaters | 12/22/2008 |
| Q: The original beaters on our Sunbeam Mixmaster MMA finally came apart. I bought replacement beaters ... A: Older Sunbeam mixer beaters had a double slot in the top where the new beaters only have one slot ... | |
| Multichef Jetstream model JS 2000 | 12/21/2008 |
| Q: This is weird.When I put the expander ring on my oven,I can't trust it to maintain a set ... A: When something is electronic that usually means that the whole circuit board has to be replaced. ... | |
| Multichef Jetstream model JS 2000 | 12/21/2008 |
| Q: This is weird.When I put the expander ring on my oven,I can't trust it to maintain a set ... A: I am not familiar with this brand but my guess would have been the thermostat as well because the ... | |
| Model 30DM | 12/21/2008 |
| Q: I saw your response to the question about brush caps back in April. Did anyone ever find brush caps ... A: If the caps from the newer unit actually fit the older model, definitely take them and see if they ... | |
| Sunbeam Mixmaster 7-01-9c | 12/19/2008 |
| Q: I am wondering if you have a stand from this mixmaster? I bought it used not knowing it didn't have ... A: I think this is a model 9 mixer and if that is the case it is very old. I may have something used ... | |
| Sunbeam Mixmaster | 12/19/2008 |
| Q: When the machine gets turned on the beaters clack against one another. They seem to be seated ... A: The gears in the mixer are probably getting worn and should be replaced. You do not list the model ... | |
| Kenmore Micro 72189941490 Handle Replacement | 12/19/2008 |
| Q: Kenmore Micro 72189941490 is 12 years old and the andle snapped at the screws. I have a replacement ... A: You should talk to a Sears Service Center to find the answer to this question because Sears does not ... | |
| Old Sunbeam Mixmaster Mixer bowl won't turn by itself very well | 12/18/2008 |
| Q: I saw your answer, but the stand of our Model 1940 doesn't have a screw to adjust beater pressure on ... A: It sounds like the button on the beater is about the right length. I am not at work so I can not ... | |
| Kemore Microwave | 12/18/2008 |
| Q: We are using a over the stove mounted microwave. Last night while trying to warm up a meal I hear a ... A: You will have to contact Sears Service and give them the model # of your unit. They should have a ... | |
| Sunbeam mixer problem | 12/17/2008 |
| Q: My 1-7A stand mixer only operates at the highest speed. At lower speed settings, it pulsates in ... A: I could be one of two things. The speed control may be not working properly or the capacitor may be ... | |
| GE Microwave | 12/16/2008 |
| Q: I have a GE Spacemaker XL 1800 microwave that simply stopped working. I replaced two 20v fuses and ... A: Did you check continuity of the door switches? One is usually normally open and two are usually ... | |
| Westinghouse Roaster Insulation | 12/15/2008 |
| Q: I have a Westinghouse Roaster early 50's model, I am going to take it apart and have it repainted. ... A: If you are taking out the insulation, be very careful as it will probably be asbestos. You will ... | |
| sunbeam electric blanket replacement cord | 12/14/2008 |
| Q: Of the 4 wires in the cord for my kingsize elctrict blanket one is broken clear through. Is there a ... A: I do not think that Sunbeam has any replacement parts for their blankets but you can try their ... | |
| Oster Kitchen Center mixer arm | 12/14/2008 |
| Q: My wife's Oster Kitchen Center mixer arm got jammed and broke some teeth off a couple of gears. I ... A: We use a light application of a good atuomotive wheel bearing grease. It will stick on the gears ... | |
| Door Alignment microwave | 12/13/2008 |
| Q: Just purchased an over the stove microwave, (Kenmore-Sears) I noticed that the door is not aligned ... A: The unit is still under warranty so I would not try to adjust the door. If you do and something ... | |
| What kind of grease? | 12/13/2008 |
| Q: I am rebuilding an older Oster kitchen center, and the grease is old and gummy. What kind of grease ... A: If you are rebuilding the mixer head, we use a good automotive wheel bearing grease. It will stick ... | |
| Hamilton Beach Scovill Model 60 Stand Mixer | 12/13/2008 |
| Q: I inherited this wonderful stand mixer when my mom passed away five years ago. It works perfectly, ... A: If you go to our web site and request this part, we will try to locate a used one as new have not ... | |
| Sunbeam mixmaster 1960 | 12/11/2008 |
| Q: My turntable got broke, and I am looking to purchase another one for my mixmaster. The model# is ... A: I think that I may have a good used one but I am not at work today to look it up. If you will ... | |
| percolator cord... | 12/11/2008 |
| Q: I won a Royal Rochester percolator on ebay. However, it didn't come w a cord. Do you know where I ... A: I know of this brand of perc but do not know what kind of cord it takes. If you will call us with ... | |
| dryers | 12/11/2008 |
| Q: My dryer will make a noise after it has run for a while. How can I tell if it is a bearing or the ... A: If you have a small hair dryer, the problem is probably in the motor bearings. If you are talking ... | |
| Kitchenaid mixer | 12/10/2008 |
| Q: I tried to change the motor brushes but they do not come out. They seem to be stucked. I pulled out ... A: Kitchenaid brushes have an angled piece cut off of one side of the brush and sometimes they catch in ... | |
| Everstar Slow Cooker | 12/9/2008 |
| Q: I received this slow cooker as a gift and unfortunately there isn't a manual. Could you please give ... A: I am not familiar with this brand at all but I will try to sort it out the best that I can. The two ... | |
| toaster | 12/9/2008 |
| Q: I have a STAR-RIGHT model525. Made in Torrington, Conn. I want to know if there is any way to get it ... A: I am not familiar with this brand but it sounds like a very old unit if you have to watch it toast. ... | |
| Cuisinart CSB-1C | 12/9/2008 |
| Q: I need the little spring that holds the blade onto the unit. Mine fell off when washing it. I know ... A: I have had good luck at Ace Hardware stores for springs. Cuisinart is now owned by Conair and they ... | |
| Brown Bobby Triangle Donut Machine | 12/8/2008 |
| Q: My dad has a Brown Bobby Triangle Donut Machine made by The Food Display Machine Corporation at 500 ... A: I have seen some machines similar to this but not this particular brand and not as old as your ... | |
| HELP! Sunbeam mixmaster is smoking | 12/8/2008 |
| Q: I recently bought a sunbeam mixmaster at a garage sale and after I brought it home , I tried using ... A: The model MMA is one of the better models that Sunbeam made but they have a resistor in them that ... | |
| shaver/waffle iron | 12/7/2008 |
| Q: i have a norelco model # sc 8130,this was my fathers shaver that was bought before 1972,i had ... A: I may still be able to order new blades and screens for your fathers shaver but they will be made in ... | |
| Porcelier trade mark mfg co | 12/6/2008 |
| Q: I bought this at a auction today on DEC 6,2008 it is Porcelier coffee pot and sugar & cream set. But ... A: First we would have to know if the pins in the pot are flat or round. The second is: what is the ... | |
| Mixmaster attachment | 12/5/2008 |
| Q: Back in the '60's my mom used a hand held Mixmaster to make whipped cream. The attachment she had ... A: The only place that I know of that you may find something like this is on Ebay or Craigslist. I ... | |
| #25 Hamilton Beach Milkshake mixer | 12/4/2008 |
| Q: I just bought a #25 Hamilton beach mixer on E-bay and I would really like to know what year it was ... A: If there is a # stamped into the tag or frame it should be a date of manufacture. It may be a four ... | |
| Sunbeam mixmaster heritage | 12/4/2008 |
| Q: I have a less than a year- old mixmaster. On the second or third time of use, the bowl failed to ... A: If you will go to the Sunbeam website and insert your model # you will see the parts that may be ... | |
| Sunbeam mixmaster heritage | 12/3/2008 |
| Q: I have a less than a year- old mixmaster. On the second or third time of use, the bowl failed to ... A: There is a separate motor that moves the bowl and that motor must not be working. Please check the ... | |
| GE hand mixer | 12/2/2008 |
| Q: I have a Turquoise GE hand mixer that belonged to my mother. The Model is 18M37. How can I find ... A: It should be stamped in the frame near where the Model # is listed. It will probably be four to six ... | |
| Dehumidifiers | 12/2/2008 |
| Q: Do you know of any manufacturers that sell a dehumidifier containing a copper coil? Just looking ... A: I do not know of any still using copper. I would purchase a used unit that does not have any ... | |
| 1906 Coffee Pot | 12/1/2008 |
| Q: I have a 1906 Universal Coffee Pot made by Landers, Frary & Clark that the cord is missing from. It ... A: First we will have to know if it has flat or round pins on the coffee maker? The second question ... | |
| sunbeam 20-3 Ag oaster | 12/1/2008 |
| Q: toaster turns on lowers toast but it will burn toast without raising again, how do I adjust ... A: There is a screw on the bottom of the unit that only adjusts the lowering part of the cycle. This ... | |
| Hamilton Beach scovill 25 | 11/30/2008 |
| Q: I recently purchased a H.B. Scovill model 25 it is missing the timer knob. Are replacements (Timer) ... A: I think that I would have a generic timer knob for this unit if the shaft is not broken off but the ... | |
| Sunbeam Heritage mixmaster | 11/30/2008 |
| Q: We have a Heritage 2350. My wife was just mixing frosting when the blades stop spinning. The motor ... A: You have stripped the plastic gears in the head. The only parts that I may have would be used. If ... | |
| re:4hp 20gal. Sears air compressor | 11/28/2008 |
| Q: I bought a house two years ago, and one of these is mounted in the garage. I turned it on for the ... A: Do not worry about explosions as long as the over pressure bleeder valve is working. Usually there ... | |
| Microwave Light | 11/28/2008 |
| Q: The light inside my GE Spacemaker XL1800 range top microwave blew out. I followed the instructions ... A: Probably. Every microwave is wired differently so it is hard to say but I would test the fuse with ... | |
| Westinghouse Roaster Oven | 11/28/2008 |
| Q: The oven I have is old. It has a catalog # RO-915. It still works just fine but the glass knob or ... A: Westinghouse has not made ovens in over 20 years so needless to say, parts are no where to be found. ... | |
| Sunbeam Mixmaster Model 12 | 11/28/2008 |
| Q: I have this old mixer with a bad switch. I am about to trash it, but decided to look into ... A: If you have all of the parts, I can rebuild the switch. If you will send me just the speed control ... | |
| speed control resistor | 11/27/2008 |
| Q: I have a Sunbeam Mixmaster model 1-8B. It "cuts out" when in use and it appears the resistor has ... A: These are not available any more but I think I have found a replacement but they have to be soldered ... | |
| Old Sunbeam 235 w Mixmaster | 11/27/2008 |
| Q: How do you remove the beaters? A: You do not list a model # so I will guess that you have one that the handle has to be tilted to the ... | |
| Kenmore Microwave | 11/27/2008 |
| Q: My question is, the housing that the magnetron srews up into the top of the housing has a few small ... A: If the holes were burned into the metal by the old tube, I would use metal screws and galvanized ... | |
| Kenmore stand mixer model 400 | 11/26/2008 |
| Q: I have a Kenmore model 400 stand mixer. It is a white unit with a chrome top. I have one beater with ... A: Kenmore never made any mixers. They purchased them from either Sunbeam or Hamilton Beach. They did ... | |
| Sunbeam Mixmaster power cord | 11/26/2008 |
| Q: I have a vintage Sunbeam mixmaster that the power cord is cracking and needs to be replaced. I have ... A: Some old Sunbeam mixers had plug in cords and some were hard wired into the unit. If we replace any ... | |
| Small Electric Motor | 11/26/2008 |
| Q: My son approached me yesterday with an oddhis PS2 controller didn't vibrate anymore. So, having been ... A: I am guessing but it could be that the field coil or armature is running and after a min. or so it ... | |
| Westinghouse roaster oven | 11/26/2008 |
| Q: I have a old roaster oven. It has two tips for the tub to fit on upside down. Can I roast a turkey ... A: I am not quite sure what you are asking but I will try to answer. Most roaster ovens have a pan that ... | |
| Kitchenaid repair | 11/26/2008 |
| Q: When we were using our Kitchenaid Mixer. The bowl slipped off the base and hit the beaters. The ... A: There is a pin that shears off inside of one gear but that does not stop the motor from running. ... | |
| GE Profile 1800 XL series microwave | 11/25/2008 |
| Q: everything appears to work but does not heat. Just had it re-located and changed to outside exhaust ... A: This should not have effected the operation. If the fan motor is running and the clock counting ... | |
| Oster Chrome Belgian Waffle Maker 3878 | 11/24/2008 |
| Q: My Oster Chrome Belgian Waffle Maker 3878 is missing the Variable Temp Control switch and the read ... A: Go to the Sunbeam website and type in this model #. It should tell you what parts are available for ... | |
| New oven door won't close | 11/22/2008 |
| Q: MY brand new and newly installed GE wall oven has a door that just won't quite close (actually, it ... A: I am not a large appliance expert by any means as we repair only small appliances but if it works ... | |
| GE Spacemaker 2.0 | 11/21/2008 |
| Q: I have a GE Spacemaker 2.0 microwave oven. It is about three years old and when you activate the ... A: I would guess that you may have a problem with the main control circuit board or the touch board. ... | |
| Sunbeam Mixmaster Heritage series | 11/21/2008 |
| Q: We have had the mixer less than one year and one mixer blade is hitting the bottom of the stainless ... A: I am not really familiar with the new models of Sunbeam mixers as we have not seem many of them yet. ... | |
| kitchenaid artisan mixer | 11/20/2008 |
| Q: My mixer does not seem to start when I turn it on, why? A: You do not state a model # so I will assume that it is a newer model. Kitchenaid has been having a ... | |
| microwave oven and power strip | 11/14/2008 |
| Q: My microwave oven works and my power strip which it is plugged into seems to work on the toaster or ... A: The circuit breaker in the strip is getting weak and is overloading and snapping off. The best way ... | |
| small oscillating table fan | 11/13/2008 |
| Q: Wayne I have an old G.E. fan that I would like to have repaired. I believe there is a gear problem ... A: We do repair some older fans but the gears would be a problem. We deal mostly in rewiring. There ... | |
| microwave oven and power strip | 11/13/2008 |
| Q: My microwave oven works and my power strip which it is plugged into seems to work on the toaster or ... A: They are both probably working properly. You should never plug a microwave into a power strip. It ... | |
| hair dryer | 11/9/2008 |
| Q: My daughters hair dryer does not blow on high. It does blow on low. When we plug it into a different ... A: You may have a cord or plug problem. The cords tend to break inside the plastic coating on the wire ... | |
| KFP 700 Food Processor | 11/8/2008 |
| Q: I have an old Kitchenaid food processor made by Hobart. It works GREAT except that I lost one of ... A: I would try to find a different magnet somewhere. The magnet has to be in place for the bowl to ... | |
| Ice Maker | 11/8/2008 |
| Q: Could an ice maker be installed in a chest type freezer? A: I am not familier with freezers as we do not sell or service them. I have never seen one but that ... | |
| Landers, Frary & Clark Universal Heating Pad | 11/5/2008 |
| Q: I have an old metal box in excellent condition. The inside of the box identifies that it housed a ... A: I have not heard of this company but have you done a search through Google on the company. You may ... | |
| B & D toaster oven door spring repair | 11/5/2008 |
| Q: I purchased a new Black & Decker toaster oven a couple of months ago and the door started flopping ... A: If the unit is only two months old, put it back together and take it back where you bought it for a ... | |
| GE convection microwave oven | 11/4/2008 |
| Q: I have a GE convection microwave which functioned fine until yesterday when I gave it an intense ... A: I think you need a repairperson. There may be a way of rebuting the control board but you have to ... | |
| GE Microwave repair?? | 11/3/2008 |
| Q: I have a GE Profile series Spacemaker XL1800. the unit recently burned out both of the bulbs for the ... A: I think the problem is probably in the control panel or the main PC board. It will be very ... | |
| ROWENTA STEAM IRON Model DE011 | 11/2/2008 |
| Q: Have been having problem when I plug in. Some times it won't turn on but if you play with plug it ... A: I would guess that your problem is in the plug where it plugs into the outlet. The wires tend to ... | |
| Mixmaster Milkshake maker Model 9b | 11/2/2008 |
| Q: my mother in-law picked up an old 6 place, Mixmaster Milkshake maker in near new condition. Under ... A: These are almost impossable to find. The reason is that they get old and brittle and break. These ... | |
| T-Fal toaster | 11/2/2008 |
| Q: I have a T-Fal TT 812051/3DO - 5324.51 - 2-slice toaster which recently blew up in flames. Although ... A: We are not an authorized service center for T-Fal so we do not have this information. I would try ... | |
| Quasar microwave model QM8850TW | 10/29/2008 |
| Q: I need the amount of voltage that goes through the low voltage transformer; the part number ... A: If this transformer is on the circuit board you will have a problem. As you have seen, there are no ... | |
| Bad connection on Sharp Carousel OTV MW? | 10/29/2008 |
| Q: I believe our electric system on the MW is in good working order but the mechanical connection from ... A: I would guess that your problem is in the alignment of the door to the switches inside the unit. ... | |
| Water Softner Timer | 10/28/2008 |
| Q: I have a Sensimatic Water softner (Now out of business) with a defective timer motor. It is a 120V ... A: These usually resemble electric clock motors. They are usually 1 RPM motors but have many different ... | |
| Quasar microwave model QM8850TW | 10/28/2008 |
| Q: I need the amount of voltage that goes through the low voltage transformer; the part number ... A: The only way to tell that is to use a volt meter and check between the two wires feeding the low ... | |
| model 10 sunbeam mixer | 10/27/2008 |
| Q: I purchased the capacitor for this mixer to solve the high speed only problem. Soldered it in place ... A: The speed control may be the problem. You can send it to us as we have a way to rebuild the speed ... | |
| fan noise for t-fal toaster/convection oven | 10/27/2008 |
| Q: We just purchased a t-fal convection toaster oven. We hear a ratling like sound when we use the ... A: No. It sounds like the fan is loose on the motor shaft. I would call them back and be more ... | |
| Hot plug and wire on vaccuum | 10/24/2008 |
| Q: My vaccuum cleaner work very well but every time I go to unplug it after using it, even for a few ... A: If the heat is coming from the plug end you should replace the plug. Wires inside the cord tend to ... | |
| Oster Coffee Bean Grinder | 10/19/2008 |
| Q: I found a Oster coffee grinder that attaches to my Oster Kitchen Center. When you remove the plastic ... A: I have never in all of the years of working on Kitchen Centers, seen a coffee grinder attachment. ... | |
| Frigidaire FMV156DC Microwave | 10/17/2008 |
| Q: I agree with the comments previously posted by Shakey. My Frigidaire microwave is just over a year ... A: I do not think that there is a door height adjustment but you should be able to adjust the door ... | |
| vintage sunbeam mixmasters | 10/16/2008 |
| Q: I just bought 2 old sunbeam mixmasters; #11C and #V14CWS. The #14 is missing the turntable; do you ... A: We may be able to help you but I am not at the shop now. The only turntable that we may have would ... | |
| cordless phone | 10/15/2008 |
| Q: I have a KX-TG1033S Panasonic cordless phone in a 200 yr old stone house with 2 foot thick stone ... A: First I would try to place the base unit close to the wall in question. See if that will help the ... | |
| Hamilton Beach No. 18 Mixer | 10/15/2008 |
| Q: I ran across a response you wrote to someone else regarding a Hamilton Beach No. 18 milkshake mixer ... A: The field coil is shorting out to ground. If you replace the 2 wire cord with a 3 wire cord and ... | |
| Sunbeam 2347 Heritage Mixmaster broke under heavy load. | 10/13/2008 |
| Q: I was using the dough hooks on what I now know was too much dough at one time. The mixer made a ... A: This mixer has plastic gears in it and you have stripped them out. They are not available new but I ... | |
| MICROWAVE LIGHT | 10/12/2008 |
| Q: Wayne you are well! Hope also that microwaves fall into your range of interest! I have a ... A: The first thing to do is always unplug the unit. If there is a panel with screws close the lamp, ... | |
| SunBeam Mixmaster 1-7A | 10/11/2008 |
| Q: I have a SunBeam Mixmaster stand mixer that I need a power cord for. Do you have any suggestions as ... A: Some of the 1-7A mixers had a wired in cord and others had a plug in type cord. If you have the ... | |
| american harvest fd 1000 dehydrator | 10/10/2008 |
| Q: how does it come apart. i took every screw out of the bottom took out the temp knob and the off on ... A: I am sorry but we have never repaired one of these. With this type of unit, we usually have to do ... | |
| Sunbeam mixmaster 12c beaters | 10/7/2008 |
| Q: I have bought 2 different beater blades that do not match my shaft connection saying they should in ... A: The old style beaters were the x pattern and the newer style have only a single slot. Try removing ... | |
| royal rochester percolator | 9/27/2008 |
| Q: I recently purchases a 1940's Royal Rochester percolatr. It heats up fine, my question is how long ... A: You will have to determine the correct time. It all depends on how much coffee and how strong you ... | |
| Waffle Iron | 9/27/2008 |
| Q: I have an antique Universal (Landers, Frary and Clark) round waffle iron. Patented in 1923 and 1924. ... A: I have some obsolete parts for old appliances but would have to see the feet to see if I could help ... | |
| Cuisinart coffee maker | 9/26/2008 |
| Q: We have a Cuisinart Coffee maker which is several months old. The brew-pause feature leaks quite a ... A: Cuisinart does not make any parts for their coffee makers so you can not replace the basket. I ... | |
| MixMaster Model 12 | 9/26/2008 |
| Q: I have a mixmaster model 12 that runs correct at slow speeds through speed number 3 and when it is ... A: The speed control is not working properly but we would have to see the unit as there could be any ... | |
| Black light knob for Rangaire Hood Ser # 05941 151491 | 9/26/2008 |
| Q: P-L-E-A-S-E help me find the knob for this range hood! Thank you for your help! A: If it has a 1/4" dia. shaft on the switch that you are looking for I may be able to help you. ... | |
| Sunbeam Mixmaster Model 10 beaters | 9/26/2008 |
| Q: I just got an old mixer, and I'm not sure of what the process is to properly insert the beaters. On ... A: The handle should be in the upright position when inserting the beaters and be sure to push them in ... | |
| HAMILTON BEACH MODEL 33 MALT MIXER | 9/24/2008 |
| Q: I AM REFURBISHING ONE OF THESE SPLENDID MACHINES AND WOULD LIKE TO KNOW WHERE I CAN OBTAIN SPARES. A: I have seen a number of them on Ebay. They have not been made for over 40 years so that is probably ... | |
| Whirlpool AD40USR Humidifier | 9/24/2008 |
| Q: I just bought a used Whirlpool AD40USR humidifier and it appeared to be working during the ... A: More than likely the people that owned the unit either had pets or smoked. Either could be causing ... | |
| Sunbeam Mixmaster | 9/14/2008 |
| Q: The 12-speed controller knob on my Sunbeam Mixmaster (Service Number 1-7A)is loose. How is the knob ... A: I think that model has a decal on the back. You have to use a hair dryer and melt the glue that ... | |
| Sunbeam Electric Blankets | 9/11/2008 |
| Q: Kiefer, I'm happy to find someone so knowledgable in this area. Thanks for being there. I read a ... A: The main problem is not in the blanket, it is either on or off. The problem is with the control ... | |
| Hamilton Beach #1 Cyclone malt mixner | 9/10/2008 |
| Q: Good afternoon, I have what I believe to be a very early Hamilton Beach Malt mixer. It sits on a ... A: You are in the same position that we are in many times a day. There are no repair manuals for small ... | |
| samsung microwave | 9/10/2008 |
| Q: I bought a microwave in Jan.o8, and the handle in which I thought was metal turned out to be ... A: If the door is getting moisture between the glass, the seal is not operating as it should and the ... | |
| over range microwave placement | 9/8/2008 |
| Q: How much space should there be between the bottom of an over-range microwave and the cook top of ... A: Every city or town has their own codes for this. You should contact your local building inspector ... | |
| Delonghi DSM7 stand mixer | 9/8/2008 |
| Q: My mixer which is equipped with an overload protection device (PC board) has sopped working. I have ... A: Ten years ago we used to be a Delonghi dealer but they do not have any dealers any more. I have ... | |
| Dehumidifier compressor extremely hot! | 9/8/2008 |
| Q: I have a Kenmore 30 Pint Dehumidifier that wasn't running. After troubleshooting I determined a ... A: You are correct in your troubleshooting. The unit that you removed is the circuit breaker and it is ... | |
| 01266 Sunbeam Mixmaster | 9/7/2008 |
| Q: I was given this mixer. But it does not have the part that goes under the turn table that makes it ... A: If you will pose this question to us at: info@kieferappliance.com , we will be glad to look at our ... | |
| Microwave venting | 9/5/2008 |
| Q: My over the stove GE microwave (2 yr old) does not vent well. Consumer guide said none of these ... A: If this unit is connected to an outside vent that has a blower motor, you may be able to purchase a ... | |
| Danby Microwave Error Code | 9/3/2008 |
| Q: My Danby microwave has started to beep every couple of minutes and displays an error code 1:10. Just ... A: Every micro wave is different and I am not familier with this model. Sometimes an error code can be ... | |
| Whirlpool Gold Accubake System Microwave | 9/2/2008 |
| Q: I had a power outage at my house and when the power was restored the microwave light doesn't come on ... A: It sounds like the power serge burned up a door switch or the circuit board and the control board is ... | |
| Everstar ice maker | 9/2/2008 |
| Q: We have a customer with an Everstar ice maker Model # HD1M35 and we need a water pump for it. Can ... A: I am not familier with this brand but if it says "Made in China" on the unit, you will probably not ... | |
| Royal Rochester Percolator fuse? | 9/1/2008 |
| Q: Mr. Wayne Kiefer; Was at a Rummage sale and came across a Royal Rochester Percolator and purchased ... A: Actually, it does. It means that the unit was made to have the fuse replaced. If you would like to ... | |
| Sunbeam Mixmaster-Model2350 | 9/1/2008 |
| Q: Hey Wayne, this is my problem. my wife, while mixing a batch of her famous chocolate chip cookies ... A: I can send you a parts diagram of a machine like yours but you will have to request it from my ... | |
| microwave LED faded | 8/31/2008 |
| Q: i have a sharp model r1601 that i can't read the display because of it fading. it has been unplugged ... A: I think the main touch control board is bad and there is not much you can do but replace it and with ... | |
| Vintage Hamilton Beach Scuvill model 25 | 8/31/2008 |
| Q: I bought this at a garage sale for $1.00 and it works perfect--no vibration etc. Anyway, is there a ... A: This is a very good old mixer and should last a long time. There is supposed to be a special screw ... | |
| Royal Rochester Percolator fuse? | 8/30/2008 |
| Q: Mr. Wayne Kiefer; Was at a Rummage sale and came across a Royal Rochester Percolator and purchased ... A: I am not familier with this brand but I assume it is very old. If you can take a picture of the ... | |
| Plug button | 8/27/2008 |
| Q: I had to replace a handle that broke on my Whirlpool MH6700xx-0 microwave, which was purchased in ... A: There is a special type of appliance paint that you can get to use for such applications. It comes ... | |
| Plug button | 8/27/2008 |
| Q: I had to replace a handle that broke on my Whirlpool MH6700xx-0 microwave, which was purchased in ... A: There are appliance dealers on the internet that deal only in obsolete parts. Try a search on ... | |
| Hamilton Beach Standing Mixer Model G and Faberware FCM300 | 8/22/2008 |
| Q: I have an old Hamilton Beach Stand Mixer Model G and I need a new handle for it. Do you know where I ... A: The mixer handle I may be able to help you with as we do have a good supply of used parts for old ... | |
| shop vac | 8/22/2008 |
| Q: I am in Florida dealing with Fay and I have a shop vac do I need a filter for liquid extraction. A: Most wet/dry vacs do not us a filter for water pick up. I suppose that you could use a foam filter ... | |
| Sunbeam Mixer Model #01266 | 8/20/2008 |
| Q: I have Sunbeam Mixmaster mixer, model # 01266 with a loose speed control. The mixer is probably ... A: Now I see what you have. Sunbeam only made this model for two years and they discontinued all parts ... | |
| Sunbeam Mixmaster Model 11 Power Resistor | 8/19/2008 |
| Q: I purchased the above item from an antique store and before purchase I tried it out and it seemed to ... A: I think the repairman that you talked to may have been wrong. The low end and high end speeds are ... | |
| Sunbeam Mixer Model #01266 | 8/19/2008 |
| Q: I have Sunbeam Mixmaster mixer, model # 01266 with a loose speed control. The mixer is probably ... A: I looked in my books from Sunbeam and could not find a 1266 model. Is the speed control a mechanical ... | |
| Kenmore Dehumidifier | 8/19/2008 |
| Q: I have a Kenmore dehumidifier, model 580.54701400, that the fan won't run. The compressor kicks on ... A: I would agree with your theory. If you are getting power to the motor and it does not run, you have ... | |
| rechargeable battery for a portable hairdryer? | 8/19/2008 |
| Q: I'm looking for either a NiMH battery or a Lithium Ion Battery pack that I could use to make a 1200 ... A: Are you sure you require 1200 volts? This is quite high. I do not think you will get 30 minutes ... | |
| hamilton beach model H | 8/18/2008 |
| Q: i have recently acquired a Hamilton beach model H stand mixer, it has no attachments other than the ... A: I would have new beaters in stock but any other attachments would have to be used from Craigs List ... | |
| everstar crock pot dse-60 | 8/14/2008 |
| Q: How can I buy a lid for a everstar crock pot model DSE-60? A: Parts for appliances are very hard to get lately. Everything is being made in China and they do not ... | |
| Parts for | 8/13/2008 |
| Q: I am missing the top of the pot and the cord that has a 3/4" pin spacing. Any Ideas on where I can ... A: If you will give us the measurement of the hole diameter on the top I probably have a glass insert ... | |
| G.E. Toaster Cat # 139T81 | 8/11/2008 |
| Q: I am trying to obtain repair instructions for this toaster. Specifically, how to PROPERLY open it ... A: It seems that GE made about 50 different models over the years so I am not sure what yours looks ... | |
| G.E. Toaster Cat # 139T81 | 8/11/2008 |
| Q: I am trying to obtain repair instructions for this toaster. Specifically, how to PROPERLY open it ... A: I have never seen repair instructions for any GE appliance. They just do not want any one working ... | |
| Sunbeam Mixmaster | 8/11/2008 |
| Q: I have a Sunbeam Vista Mixmaster Mixer, 235 watts, 12 speeds (have searched all over the appliance ... A: You should replace both the resistor and the capacitor. This will solve your problem. We have both ... | |
| Sunbeam Mixmaster Stand Mixer | 8/10/2008 |
| Q: I only have a service # 80-37BD, no model number can be found. It's old, I know, but I love it. ... A: We repair mixers like yours every day and have most of the parts in stock to repair them. If you ... | |
| Everstar Ice Maker | 8/8/2008 |
| Q: I just bought a home and it has an under the counter ice maker by Everstar Appliances, Model ... A: I have no contacts with Everstar so I am not going to be much help but have you tried their website? ... | |
| fan motor | 8/8/2008 |
| Q: I have a fan that is not working, how do I test the motor and switch with a multimeter. The switch ... A: Do not do this test with the fan plugged in to a socket and disconnect the switch from the motor or ... | |
| antique coffee perc | 8/7/2008 |
| Q: I have a "Porcelier" porcelin coffee perc from 1938 by Porcelier MFG Co. Greensberg Pa Cat # 410. ... A: I have generic fuses that will work in your coffeemaker but the problem is to get the correct ... | |
| microwave | 8/7/2008 |
| Q: I have an electrolux over the range microwave and it shows an error code of ES?? the light comes on ... A: It sounds like the control circuit board is malfunctioning. You may find that the repair cost is ... | |
| GRAIN GRINDER FOR OSTER KITCHEN CENTER | 8/6/2008 |
| Q: This is not so much of a repair question as a general question. I have an Oster Kitchen Center and ... A: If you have the coffee grinder attachment, it should work for grains. Coffee beans are harder than ... | |
| everstar coffee makere | 8/6/2008 |
| Q: Where can I buy a pot for and Everstar coffee maker, live in California, online is ok, Thanks Jorge A: Try a search for "small appliance service" and see what you can find in Ca. I think you may have to ... | |
| West Bend bread machine overheats | 8/6/2008 |
| Q: We have used a West Bend horizontal loaf bread machine Model 41085 "Bakery Style" 11/07/97 for about ... A: We used to be a West Bend service center but they did not make any bread makers here. They bought ... | |
| Oster Coffee Maker Model: 3309-33 (Canadian model) | 8/5/2008 |
| Q: I just bought this coffee maker, and am pleased with the coffee it makes, but it has a very annoying ... A: If you can get it apart and locate the alarm mechanism, you should be able to disconnect one of the ... | |
| electric cord for Black & Decker griddle | 8/4/2008 |
| Q: I need a plug-in cord for a B & D mod #GR100 griddle. I've seen other inquiries to you about ... A: We are not a B & D authorized dealer any more so I do not have any parts books to look up this part. ... | |
| Sunbeam Waffle Maker &Grill Model CG | 8/4/2008 |
| Q: The temperature switch on our unit will turn on and off With the heating coils getting very red, ... A: There are only two or three components to a waffle iron and it sounds like the thermostat is bad in ... | |
| Mixmaster MMA | 8/2/2008 |
| Q: I got an old model at a yard sale. It has a juicer and some other items with it that are in good ... A: MMA is the model # that you will need to order any parts for this unit. It is about 20-30 years old ... | |
| Fuse at Microwave | 8/2/2008 |
| Q: My microwave (Sharp Carousel II; about 18 years old) stopped working. I opened it up and checked the ... A: I have not heard the term "monitor switch" used in other microwaves but it seems like every manf. ... | |
| basement dehumidifier | 7/28/2008 |
| Q: I have two Kenmore dehumidifiers, model 580.54701. 70 pint low temp dehumidifiers and a third one ... A: The old dehumidifier uses a different, more efficient, freon and therefore will take out moisture ... | |
| Sunbeam Mixmaster MMA | 7/28/2008 |
| Q: I recently became the owner of a Mixmaster MMA, which appears to be in good shape, other than the ... A: You can try one trick and see if it works before getting new beaters. The snap rings have to fit ... | |
| B&D overcounter coffeemaker | 7/27/2008 |
| Q: You have to bang on the thermal switch to make it brew. I beleive it needs a new one, the number is ... A: We sell parts as well but B & D does not sell any parts for this unit. We may have a generic ... | |
| Rangaire Vent-A-Hood Model 2-747 | 7/27/2008 |
| Q: I need a filter for my Rangaire Vent-A-Hood. The dimensions are 18 3/4" x 9". It is a metal mesh ... A: There are websites on the internet that will make any size that you need. Just do a search and you ... | |
| Kenmore microwave | 7/16/2008 |
| Q: I have a Kenmore microwave model # 721.62349201 that has quit heating. Any suggestions on ... A: It could be anything and with labor costs as high as they are today, I would check on a price for a ... | |
| Sunbeam Vista Food Processor: S Blade | 7/16/2008 |
| Q: We came across a Sunbeam Vista Professional Food Processor. It has a lot of slicing tools and the ... A: You should go out and purchase a lottery ticket because this is your lucky day. These have not been ... | |
| vintage Sunbeam mixmaster | 7/16/2008 |
| Q: I was given on older 12-speed Sunbeam Mixmaster stand mixer. Everything on it works great. My ... A: Most of the old Sunbeam mixers had the service # located near where the beaters go into the mixer. ... | |
| 1953 Sunbeam Square Waffle Iron | 7/16/2008 |
| Q: I need a replacement cord for this jewel. Would prefer a coiled cord if possible as the cord is ... A: I do not know of any appliances that use a coil cord. They have to be a special HPN heat cord. We ... | |
| Toaster Convection oven as a food dehydrator? | 7/15/2008 |
| Q: I have a Oster countertop toaster/convection oven. I want to dry herbs from my garden as gifts for ... A: They are not advertised as a dehydrator but I do not see why it would not work. I would place an ... | |
| everstar coffee maker | 7/14/2008 |
| Q: I have an everstar programable 10 cup coffee maker in which the "POT" itself fell off the counter ... A: I am not familiar with this brand but it is probably made in china and there are no parts available. ... | |
| Bosch Hand Mixer | 7/11/2008 |
| Q: We have Bosch Hand Mixer MFQ2100UC/01 300W. The cord has broken right where it comes out of the ... A: Most everything is being made in China now. They do not believe in screws so they snap everything ... | |
| replacement cover for westinghouse crock pot | 7/11/2008 |
| Q: How can I buy a replacement glass cover for my Westinghouse crock pot - I can't even find a ... A: You can not find a website because Westinghouse has not made a cooker or crock pot in over 15 years. ... | |
| Farberware FSM 350 stand mixer | 7/10/2008 |
| Q: Where do I find a set of replacement beaters for this mixer? Every site I hit just wants to sell me ... A: Farberware never made a mixer. They bought their mixers from outside vendors such as Sunbeam or ... | |
| sunbeam mixers | 7/10/2008 |
| Q: I have a sunbeam 60th anniversary edition mix master (clear glass bowls) and a sunbeam vista mix ... A: The only way you can get any attachments would be through Craigs list or Ebay. They did make a set ... | |
| Re: Kitchenaid standing mixer - Can't lift arm to insert bowl | 7/9/2008 |
| Q: The motor to the mixer works fine. We cannot lift the arm to insert or extract the mixing bowl. ... A: There is probably a small plastic part in the top of the stand that is broken. I can send you a ... | |
| Manual for my Harvest Maid Food Dehydrator | 7/9/2008 |
| Q: Wayne, We recently moved and lost the manual for my Harvest Maid Model FD-200. It was made by ... A: Try a search under "Harvest Maid" or "Alternative Pioneering". We never repaired any of their ... | |
| coffee perc landers,frary & clark | 7/8/2008 |
| Q: universal E9159 art deco- sentimenta value -thermostat not functioning- please help ! david wexler ... A: Some of these old units never had thermostats to turn off after the brew cycle and others did. Have ... | |
| kenmore dehumidifiers | 7/7/2008 |
| Q: I read your answer to a question about hot air blowing from a dehumidifier. I have one in my ... A: Yes, it would be better to use an air conditioner but the air conditioner would have to be vented to ... | |
| rival ice cream maker wooden bucket | 7/7/2008 |
| Q: my ice cream maker wouldn't stop after 1 hour, so I checked the ice cream. The ice cream was frozen ... A: I have not seen a Rival ice cream maker in years. The reason that you can not find a website is ... | |
| Replacement grease screen for oven hood | 7/5/2008 |
| Q: I have an old Rangeaire oven hood, and I need a replacement grease screen for it. There is no part ... A: I used to sell them but my supplier stopped carrying them and I have not found a new one yet. I ... | |
| mixe wm40567e | 7/4/2008 |
| Q: this hamilton beach stand mixer was my mothers am trying to get a little history of the machine may ... A: The model # that you are giving me is not a # that I recognize at all. If it is an old mixer, it ... | |
| cuisinart dcc-490sa grind n brew coffee maker | 7/2/2008 |
| Q: Have used the unit for about a year. A few months ago, it suddenly began to reset itself or lose ... A: It needs a new pc board that controls all aspects of grinding and brewing. In other words it is ... | |
| Convection toaster oven | 6/30/2008 |
| Q: Is there any convection/toaster oven that is made any place other than China? You mentioned to ... A: The only two that we could ever service were Toastmaster and Farberware. Neither is still made and ... | |
| magnifying light | 6/29/2008 |
| Q: This is a typical magnifying light sold at Fry's with a base that has an electrical outlet in the ... A: If this is a standard incandescent bulb lamp the new switch may work but it it is a florescent bulb ... | |
| HB Model E mixer brushes | 6/29/2008 |
| Q: Can you suggest a source for a couple of carbon brushes for my Hamilton Beach Model E mixer? These ... A: We have brushes that will fit this mixer but you may have to use the old springs. If the armature ... | |
| Replacement cord Black & Decker Glue Gun | 6/28/2008 |
| Q: I need a cord for Model 9734. The slot for the plug is oval and about 5/8" long; the posts or ... A: If you will go to the "Dewalt" website, you should be able to look up this item and order it ... | |
| Montgomery Wards Kitchen Mixer Model 2009 | 6/27/2008 |
| Q: I bought a mixer today at a garage sale, seems to be working fine but was wondering if we should be ... A: This mixer is probably about 40 years old as Montgomery Ward has not made mixers for about that ... | |
| Dormeyer mixer replacement handle | 6/27/2008 |
| Q: I have an old Dormeyer mixer, of family sentimental value. The handle is broken; do you know where I ... A: I think I have two Dormeyer mixers left for parts. If you send me a picture of your mixer, I will ... | |
| Kitchen aid mixer | 6/26/2008 |
| Q: Just moved, unpacked mixer and there was oil that had leaked out. Mixer was not damaged. What should ... A: If the mixer was laying on it's side sometimes grease does drip out. I would stand it upright for a ... | |
| removing cutting base from blender's jar | 6/25/2008 |
| Q: I bought Hamilton Beach Blender Chef 12 Speed 2 months back. I can not remove the blender jar's ... A: This does get to be a problem. We have placed the jar nut in a vise and then turn the jar. We have ... | |
| Everstar Electric Skillet Lid | 6/23/2008 |
| Q: I have an Everstar Stainless steel skillet model # 640-499. When I was cleaning the lid it fell off ... A: I am not familier with this brand but if you will send me a picture of the cover and handle I will ... | |
| convection microwave | 6/23/2008 |
| Q: At our office, we would like to buy one appliance that can heat in various ways. Some people like ... A: I would say no in most cases. The convection ovens use a regular heating element to heat and a fan ... | |
| Microwave turntable | 6/23/2008 |
| Q: I have a 3 year old E-Wave OTC microwave that the turntable has never worked on. We tested the ... A: Most of the time the turntable motor is controlled by the main circuit board. There is an over ... | |
| spacemaker fuse | 6/21/2008 |
| Q: I have a black and decker coffee space maker ODC450. Machine quit working and no digital lights ... A: There are no parts available from B & D for this model any more. I would like to congratulate you ... | |
| gas Bar-B-Q | 6/21/2008 |
| Q: Is it possible to convert a gas bar-b-q into a propane tank bar-b-q? If so, who would I take it to ... A: We do not service gas or propane grills so I can not answer this question as an expert but I will ... | |
| GE Microwave Fan Keeps Running | 6/20/2008 |
| Q: GE JVM1870BF06 Microwave oven was left on empty until it overheated. Microwave was completely dead. ... A: It will be in the line that feeds the fan motor. I looks like a disc about 1/2 " in dia. and it ... | |
| GE Microwave Fan Keeps Running | 6/19/2008 |
| Q: GE JVM1870BF06 Microwave oven was left on empty until it overheated. Microwave was completely dead. ... A: It sounds like the problem may be in the main pc board as that is usually what controls the fan ... | |
| Hamilton Beach Malt Mixer No 30 - 33 - 934 | 6/18/2008 |
| Q: I have a few Hamilton Beach Malt mixers. I want to refurbish one, a model 30, and wish to have the ... A: We do not repair very many of these blenders any more so I will have to try to remember how we did ... | |
| KitchenAid Blender repair | 6/17/2008 |
| Q: I have a mod.#KSB50B4.The rubber blade engagement piece on top of the motor base needs ... A: I think it is a 10mm but I am not sure. I am not at the shop and will not be there until next week. ... | |
| Holmes Fan | 6/17/2008 |
| Q: The boss purchased 4 new Holmes fans for the shop, over a year ago. This summer two of the five ... A: Sorry but do you know how much liability insurance I would have to carry if I even suggested how to ... | |
| Salton "Pizza Chef" | 6/17/2008 |
| Q: Wayne. The top element on the Salton "Pizza Chef" does not heat enough for my liking. It measures ... A: Salton does not make any parts for any of their appliances so repair is out of the question. We ... | |
| sunbean toaster t-35 | 6/16/2008 |
| Q: I received this toaster as a wedding gift in 1961 and since then it has worked fabulously until ... A: This is your lucky day. We service many of these units each year and have a good supply of new and ... | |
| Sunbeam Toaster Oven Door | 6/16/2008 |
| Q: Sunbeam Toaster Oven - the door seems to have lost its 'closing spring' - it used to spring closed ... A: You are correct that all of these ovens are different but I will try to aid you. There are probably ... | |
| KitchenAid Blender repair | 6/16/2008 |
| Q: I have a mod.#KSB50B4.The rubber blade engagement piece on top of the motor base needs ... A: We can get you the part but it is not easy to replace. You have to hold the drive shaft with a very ... | |
| ge 3/4 hp electric motor | 6/15/2008 |
| Q: I am trying to figure out how to wire a bremas switch to a ge motor. Bremas has orange t9 white t2 ... A: Check, using a continuity test, the switch. See which two wires have continuity in the on position. ... | |
| Sunbeam Toaster Oven Door | 6/14/2008 |
| Q: Sunbeam Toaster Oven - the door seems to have lost its 'closing spring' - it used to spring closed ... A: Either the spring has broken or the tab that holds the end of the spring has broken. In any case, ... | |
| connecting the beaters on my mixmaster | 6/14/2008 |
| Q: How do I connect the beater on my used Sunbeam Mixmaster heritage series? The model # is 2350. I ... A: You should be able to just rotate one until it drops into place. It may go in kind of hard and that ... | |
| Sunbeam Mixmaster 10 | 6/14/2008 |
| Q: I need a new power cord for a Sunbeam Mixmaster 10, dated 1950. Any chance? A: We have the power cord that you need. It is a three wire grounded cord instead of the older two ... | |
| Microwave Oven | 6/10/2008 |
| Q: I moved into a new house this week and used a KitchenAid counter top microwave oven the first ... A: If you take the case off the unit there may be a circuit diagram taped to the inside. This should ... | |
| Beater misalignment in Sunbeam Heritage Series Stand Mixer Model 2346 | 6/7/2008 |
| Q: I read your very informative answer to an almost identical question. Unfortunately, the front of ... A: In most cases of beater misalignment, the problem is that a gear has lost a tooth or two. At this ... | |
| Beater misalignment in Sunbeam Heritage Series Stand Mixer Model 2346 | 6/6/2008 |
| Q: I read your very informative answer to an almost identical question. Unfortunately, the front of ... A: The 2346 does not have any internal parts available for it so repair is not possible. It is a ... | |
| microwave oven work light | 6/6/2008 |
| Q: when attempting to remove one of the work lights from my GE Spacemaker microwave (over the range) ... A: I think you have encountered an all-in-one type bulb. The bulb is part of the socket and has to be ... | |
| dehumidifier blowing out very hot air | 6/5/2008 |
| Q: I have a Whirlpool dehumidifier that as soon as its starts running it blows out very hot air, it ... A: If it is blowing hot air that means that the cooling system is working properly. It has to expel ... | |
| Sears Air Compressor | 6/3/2008 |
| Q: I have an old model Sears 1hp paint sprayer air compressor I got when my Granddad passed away. It ... A: You need a new check valve. This valve releases the pressure so the motor can start with no tank ... | |
| kitchenaid household blender | 6/2/2008 |
| Q: Where do I purchase the black connector on the blender? model#KSB5083.The black connector is ... A: This is a common problem with all Kitchenaid blenders. Can you get the old one off and is the ... | |
| Oster Kitchen Center | 6/1/2008 |
| Q: My wife has an Oster Kitchen Center with all the attachments. She hadn't used it for a few years, ... A: Sunbeam purchased Oster and the Kitchen Center has been discontinued for over 10 years. We still ... | |
| Sunbeam 60th Anniversary stand mixer | 6/1/2008 |
| Q: I have the Sunbeam 60th Anniversary Limited Edition stand mixer. Everything works fine except the ... A: There is an adjusting screw to adjust the tension of the beaters on the bowl. This screw is located ... | |
| Landers Frary Clark Coffee pot | 5/31/2008 |
| Q: I have a Universal Landers Frary Clark / Made in the USA/ New Britain Conn / Model #E91759, Pat July ... A: This must have been sold in the eastern US as I have not heard of the brand. The "Universal" brand ... | |
| Sunbeam Vista Stand Mixer | 5/30/2008 |
| Q: I have a Sunbeam Vista Stand Mixer and the stand broke in half. Is there a replacement stand ... A: You must have been making some very hard cookies. If you will look for the model or service # from ... | |
| sunbeam mixmaster | 5/30/2008 |
| Q: I have a model 2360 Sunbeam Mixmaster, and some months ago while I was using it it seemed to ... A: This unit has a circuit board that controls the speed and I am sorry to say, there are no parts ... | |
| Sunbeam electric blankets | 5/29/2008 |
| Q: I'm on my third blanket in about 4 years. What a waste to toss. Where is the thermostat? I'd like ... A: Most of the time the problem is in the thermostat control and it is located in the control where you ... | |
| microwave | 5/22/2008 |
| Q: The paint is peeling in my microwave and has rusted, creating a small hole all the way through the ... A: You can repaint but you have to use an appliance paint. Just to be safe, I would use a piece of ... | |
| sunbeam mixmaster power cord wiring | 5/20/2008 |
| Q: I removed the old power cord to replace, but took a year to put in the new one and now I can't ... A: There are many different models of Sunbeam mixers and without knowing which one you have it is very ... | |
| lamp wattage | 5/18/2008 |
| Q: I'm assuming you are in the U.S. but I live in the UK, where the voltage is 240, and which county's ... A: The higher the wattage, the more heat is given off. Each socket has a wattage and therefore a heat ... | |
| Sewing machine power cord | 5/17/2008 |
| Q: I have a Bernina embroidery machine that I've lost the power cord to. It would be wonderful if you ... A: We do not repair sewing machines so I do not know what the cord may look like but one of my repair ... | |
| cooker hook suction fan not working | 5/17/2008 |
| Q: My cooker hook suction fan does not work when I switch ON.The indicator light was also not working ... A: If the light worked before when the motor worked, I would guess at a bad switch. It sounds like ... | |
| dehumidifier setting | 5/16/2008 |
| Q: I own a LG dehumidifier for my unfinished basement which enables you to set a humidity level. I set ... A: I do not know the size capacity of your unit but if it is a smaller unit with only one set of coils, ... | |
| blender | 5/14/2008 |
| Q: I have a single Hamilton Beach malt mixer. The clip that holds the stainless steel cup is missing. ... A: There were three different types of this clip made. If you can take a picture and email it to us ... | |
| Sunbeam Mixer Model 2360 | 5/12/2008 |
| Q: We have a Sunbeam mixer, Model 2360, Service No. 1-46CB. The on/off, speed switch no longer works. ... A: I looked up your model and Sunbeam does not make any internal parts for this mixer. The only chance ... | |
| charger | 5/11/2008 |
| Q: I am looking for a charger for a gizmo grater A: You got me on that one. I guess I never needed any gizmos ground up. I am sure it is a "made in ... | |
| Small electric motor died | 5/8/2008 |
| Q: I have a a Honeywell Enviracare 13520 air purifier and It stopped working the other day. I turned ... A: I probably decided that that was a good time to die. The motors in these units are not the best. ... | |
| Sharp Convection carousel microwave door | 5/8/2008 |
| Q: We have a Sharp Convection Carousel microwave model number R-930AW. One of the door latches got ... A: Yes, you will have to remove the case to get at the door lock. Some hardware stores carry the ... | |
| Hamilton Beach Model G Mixer | 5/6/2008 |
| Q: My mixer needs a new power cord. Can you suggest where I can get one. The mixer is 120 watts and ... A: We have them in stock and can sell to you or we can install it for you. We always install a three ... | |
| touch lamp repair | 5/6/2008 |
| Q: What is causing my touch lamp to turn on, on its own? It was working fine until I had to replace the ... A: You may have gotten a malfunctioning sensor or it may be wired wrong. Check the diagram that they ... | |
| Hamilton Beach Super Mixette | 5/5/2008 |
| Q: I own a 1972 white (HB) Super Mixette hand mixer, I acquired it on Ebay with it's box, it runs ... A: Parts for the Mixettes are vary rare because not too many people held on the them. Most were tossed ... | |
| Mixmaster repair | 5/4/2008 |
| Q: Wayne, Do you still accept model 12 Sunbeam Mixmasters for diagnosis and repair? If you do, what ... A: Yes, we will be glad to look at your mixer. Please just send us the mixer motor only and a $10 ... | |
| Bissell pro heat | 5/3/2008 |
| Q: I am attempting to reassemble a Bissell proheat carpet cleaner after replacing fluid pump,I have ... A: I am sorry but we do not service vacuums or rug cleaners. I would suggest that you go to the ... | |
| Black and Decker GR100 griddle cord | 5/2/2008 |
| Q: We received a new gr100. We threw the box out without realizing that the cord must have still been ... A: If you will measure the distance between the pins on the griddle, I think we will be able to come up ... | |
| replacement platter for microwave | 5/2/2008 |
| Q: we accidentally dropped our glass microwave platter and broke it... Do you know where we could get a ... A: If this is the old microwave/convection oven unit I do not think you are going to find one. If it ... | |
| Sears dehumidifier date of mfg. code | 5/1/2008 |
| Q: I have a Sears dehumidifier I bought on the Internet about 3 years ago. The fan runs and the ... A: Two things to check before you ask for service on this unit. The temperature has to be at least 65 ... | |
| range | 5/1/2008 |
| Q: no expert is available for major appliances so i figure i would ask you. maybe you can help. Modern ... A: I do not service large appliances but I agree with you that the thermostat may be malfunctioning. ... | |
| Microwave Turntable | 4/28/2008 |
| Q: I have a Panasonic Microwave that is about three years old. Recently, the turn table turns when the ... A: I sounds like it may be a door switch that is supposed to turn the turn table off when the door is ... | |
| Sears Dehumidifier | 4/28/2008 |
| Q: I bought a Sears Dehumidifier, Model #580 53650200 on February 13, 2003. I paid $2l3.00 for it and ... A: You do not say what is not working about it. The motor, the cooling, or the controls? Normally ... | |
| universal landers frary and clark coffe maker | 4/28/2008 |
| Q: I have an old universal coffe maker that dose not work. it had a fuse installed I am betting that ... A: We have generic fuses that will fit many coffee makers but we have to know what temp your fuse is. ... | |
| Eureka 5847 bv | 4/27/2008 |
| Q: My on/off switch does not lock into either position firmly any more and we can not get the vacuum to ... A: Sorry, we have to be an authorized service center to have any of their repair literature and we are ... | |
| oster kitchen center | 4/26/2008 |
| Q: My wife got an old oster kitchen center from her grandma and the speed control doesn't work right. I ... A: I do have two different circuit boards for kitchen centers. If you will contact us at: ... | |
| Repair of Sunbeam Mixmaster | 4/18/2008 |
| Q: I have an old Sunbeam mixmaster which now only works on one speed. I am looking for someone to fix ... A: We repair these units all the time. If you will ship just the mixer motor assembly, we will call ... | |
| dough hooks | 4/16/2008 |
| Q: I have a wonderful model 10A1 sunbeam mixer. Can you please tell me if this will take a dough hook ... A: Yes, they did make dough hooks for this mixer but only as an attachment so not too many were made. ... | |
| Everstar Under counter Ice Maker | 4/15/2008 |
| Q: Everstar Under Counbter Ice Maker won't make ice -- makes a beeping noise. A: Sorry, but we have never seen one of these units in our shop so I can only guess at your problem. ... | |
| cg-1 waffle maker plates | 4/14/2008 |
| Q: How can I clean the waffle plates? It is difficult to get the SOS pad in between and to the bottom ... A: An oven cleaner will work but you will have to season the plates after cleaning or everything will ... | |
| dehumidifier | 4/11/2008 |
| Q: I just bought a house in Florida and was advised to leave a dehumidifier on during the summer when I ... A: First of all, if you are going to leave the machine on when you are not there, you do not want an ... | |
| Old Microwave | 4/11/2008 |
| Q: My one and only microwave that I have ever owned was made by JC Penney and is now about 24 years ... A: If you are worried about leakage, you can purchase a very inexpensive meter that will measure the ... | |
| Compressor problems | 4/9/2008 |
| Q: Sounds like I may have a similar problem. I have a 26 gal 5hp campbell Haufield compressor and it ... A: I assume you have an oil less compressor. WW Grainger used to carry parts for Campbell but I do not ... | |
| Sunbeam Stand Mixer Problem | 4/7/2008 |
| Q: I have a sunbeam dual motor 450w Heritage series. I was mixing a bread dough when suddenly the ... A: There is a circuit breaker on the motor and it must have reset after cooling. Most of the time this ... | |
| Sunbeam Stand Mixer Problem | 4/7/2008 |
| Q: I have a sunbeam dual motor 450w Heritage series. I was mixing a bread dough when suddenly the ... A: Your mixer should still be under warranty. Just send it to us and we will have a new one shipped to ... | |
| waffle iron repair | 4/7/2008 |
| Q: I understand that I have to use or have someone use "Silver Soldier to connect the HOT wire to the ... A: We try to use mechanical connectors whenever we can. They are much safer and easier to use. If we ... | |
| GE electric motor wiring | 4/5/2008 |
| Q: I have an old air compressor that I purchased a new pump for. The old pump ran clockwise, but my new ... A: It seems like every motor is wired differently. If you take the cover off of he wiring area there ... | |
| old Hamilton Beach Milk Shake blender | 4/4/2008 |
| Q: I have an old one. I can't find a model number. It's the one with the heavy green enamel feet and ... A: The brushes I would probably have in stock. The brush caps are a different story. This was the ... | |
| Mixmaster Vista model VMM-P | 4/4/2008 |
| Q: i have an old mixer that the socket for the power plug is either dislodged or broken (i bet broken). ... A: I think your has either a small cap in the center of the speed control or it may have a larger ... | |
| Mixmaster Vista model VMM-P | 4/4/2008 |
| Q: i have an old mixer that the socket for the power plug is either dislodged or broken (i bet broken). ... A: If I remember, the Vista is a split case unit. You will have to take the speed control cap off the ... | |
| general mills Dry Hand Iron | 3/30/2008 |
| Q: where can I find a thermostat for this iron A: General Mills never made any appliances themselves. They usually had either Sunbeam or Hamilton ... | |
| Sunbeam model 12C stand mixer | 3/28/2008 |
| Q: My Sunbeam model 12C stand mixer runs somewhat erratic and doesn't quite make it to top speed any ... A: It sounds like your mixer needs a little TLC. It should be taken apart and cleaned and lubricated. ... | |
| air compressor (oilless) | 3/27/2008 |
| Q: Can I use A teflon lubricant in the piston cylinder to extend life of compressor? I replaced valve ... A: The cylinder kits are not that expensive to replace in most of these units. You do not say what ... | |
| Microwave just quit working | 3/27/2008 |
| Q: We have a GE microwave that was working fine until just this morning when it began to make a very ... A: The magnatron tube is malfunctioning and has to be replaced. The problem is that it will cost you ... | |
| sunbeam T48 toaster | 3/26/2008 |
| Q: Is there an adjustment for lowering toast? What is the adjustment for screw on the side for light ... A: There are two adjustments for this toaster but you have to take the case off the adjust one of them. ... | |
| GE Spacemaker 1400XL | 3/25/2008 |
| Q: MOD: JVM1451WA001, SER: DV9807255, Manufactured 1999 Unit works fine except for lights. I have rang ... A: The GE company would be the only place that you can order the part. Check with a GE authorized ... | |
| waffle iron cord | 3/25/2008 |
| Q: I am trying to locate a replacement cord for Mom's old waffle iron (circa 1950). It is a ... A: You need a three wire HPN heat cord for this unit. We always use a three wire so there is not a ... | |
| blenders | 3/25/2008 |
| Q: How do I remove the coupler on my Kitchenaid blender model no. ksb5gr4. A: We use a metric wrench that we have ground down very thin and bent to a slight angle. Slip it under ... | |
| microwave noise | 3/24/2008 |
| Q: I have a mid size microwave three or four years old I think. It is on a counter that is a bit uneven ... A: It is very difficult for me to guess at what the problem could be from your description. It could ... | |
| replacement power cord | 3/21/2008 |
| Q: I need a replacement power cord for a Tefal waffle maker/griddle. It needs to have 3 holes, with a ... A: We do not deal with Tefal because parts are very hard to find as you are finding out. I think that ... | |
| Hamilton Beach model E stand mixer | 3/21/2008 |
| Q: I have an old Hamilton Beach model E stand mixer that was probably built in the 40's. Recently, the ... A: These are very rare. I used to carry them but the company that I ordered them from stopped making ... | |
| Wiring Question | 3/18/2008 |
| Q: I'm in the process of converting an old antique coffee pot into a lamp. The pot has the old-style 2 ... A: You have a good idea but I do not recommend what you would like to do. You will have some open wires ... | |
| crock pot doesn't heat | 3/18/2008 |
| Q: I have a Rival Smart pot, it won't heat anymore. When I plug it in the power light comes on, I can ... A: The main pc board or the element is not working properly and you have a "made in China special" that ... | |
| Spacemaker XL1800 GE Profile Microwave oven | 3/18/2008 |
| Q: The unit recently starting making increasingly loud noises. It is still heating. It sounds like the ... A: We are not an authorized service center for GE so I do not have any manuals for them. I would be ... | |
| Small utility electric heater | 3/15/2008 |
| Q: I have a small Lakewood heater(Model 792/JR) that quit working. When I opened up the unit there was ... A: Do not bypass the fuse. If you will call us at: 608-221-3322, we will be able to supply just the ... | |
| electric fan | 3/14/2008 |
| Q: in a attempt to clean a small electric fan - i removed the cover over the motor. (that was a ... A: A three speed fan will have one hot lead and three speed wires. Usually the hot lead is the black ... | |
| flat top stove | 3/12/2008 |
| Q: I have a black flat top stove and an some kind of fiber-type cloth was accidently laid down on it ... A: Have you tried turning the stove top on as low as it will go and then use the cleaner. We do not ... | |
| Sunbeam Mixmaster Model MMA | 3/11/2008 |
| Q: The handle has broken on my old reliable mixer. Is there a replacement out there somewhere? I've ... A: We should have a used handle for your mixer. Please call us at: 608-221-3322 and we can take your ... | |
| standing light | 3/11/2008 |
| Q: I recently found a very nice standing lamp with no lamp shade. It works ok but may need some ... A: It keeps the bulb tight in the socket. Some bulbs tend to loosen over time causing a loose ... | |
| Squeaky Micro turntable | 3/11/2008 |
| Q: I have a GE Profile Convection-Microwave that has started making an annoying squeaking noise when in ... A: I would have to see the unit to see where the problem is. You can try to oil the wheels on the ... | |
| ge xl1400 microwave | 3/10/2008 |
| Q: I need to change the light bulbs. how do you do this? A: Every micro wave is different. Some have a bulb that you can screw in and others have one molded to ... | |
| Kitchenaid mixer | 3/9/2008 |
| Q: Why wont a 110volt mixer work with a 220 volt step down transformer? A: It should if the wattage of the step down unit is large enough. You should check the mixer and see ... | |
| Sunbeam Heritage Mixmaster replacement beaters | 3/8/2008 |
| Q: I am desperately looking for replacement beaters for my mixer. I have another wedding cake coming ... A: Sunbeam made a few different heritage models. If you will get the model or service # from the ... | |
| Hamilton Beach Model K | 3/8/2008 |
| Q: My old HB Model K mixer has developed a loud squeak, probably from where the beaters latch in and ... A: Most of the time loud squeaks come from the motor bearings. The mixer has to be disassembled and ... | |
| GE JKP62G Microwave | 3/7/2008 |
| Q: I have a build-in GE JKP62G Microwave/oven. The glass outer door of microwave was broken itself one ... A: There are some large appliance parts dealers on the net that specialize in obsolete parts. Try the ... | |
| Toaster repair parts | 3/2/2008 |
| Q: I need a Toaster part, having no luck finding it, hate to throw it away for a simple part, I need ... A: The only way I may have it is used. If you could take a picture of your toaster and send it to me ... | |
| Central Vac motor repair | 3/2/2008 |
| Q: I had typed a full explanation but it dissapeared when I did spellcheck. Question what should I use ... A: If the motor has ball bearings, you should use something fairly thick such as a good lithium ... | |
| adjustable bed control replacement | 3/1/2008 |
| Q: I have a Niagara #3312 adjustable bed with a wired control for head & foot up/down and massage which ... A: The printed circuit board changes the 120 VAC from the plug into probably 12 VDC and sends it to the ... | |
| adjustable bed control replacement | 2/29/2008 |
| Q: I have a Niagara #3312 adjustable bed with a wired control for head & foot up/down and massage which ... A: You have to realize that I am not familiar with the bed you are asking about as we have never ... | |
| Microwave | 2/29/2008 |
| Q: I don't know if microwave ovens are in your range of expertise, but I will ask you anyway. I have a ... A: I am not sure how GE attaches their turntables but I would look on the GE website and sometimes they ... | |
| Sunbeam Mixmaster Meat Grinder PTU | 2/28/2008 |
| Q: I have a Sunbeam Mixmaster mixer, model number unknown. The only number I can locate on the mixer is ... A: You unit will take the later made unit. The 1-7A and B as well as the 1-8A and B both take the ... | |
| light fixture | 2/28/2008 |
| Q: how can I tell if a light fixture can accept 100 w bulbs? I've checked the fixture and haven't ... A: Generally if the socket and shade is light weight plastic it will accept only up to 60 watt. If the ... | |
| early 1950's Sunbeam mixmaster | 2/27/2008 |
| Q: I have a vintage sunbeam that has been in my family for 50 years. I got it from my mother last year. ... A: We repair a lot of old Sunbeam mixers as they were very well built and will last for ever, it seams. ... | |
| Sunbeam electric beater mix | 2/27/2008 |
| Q: Im after some information about a mixer I purchased in great working order, it is a Sunbeam electric ... A: If the sticker says 220-240 volts it probably will not work on 120 in the US. I do not know where ... | |
| cuckoo clock repair | 2/27/2008 |
| Q: My late husband gave me a cuckoo for Christmas one year about 10 years ago...it has been on my wall ... A: I do not know how much damage was done the clock. If the case was damaged it should be repairable. ... | |
| Sunbeam Stand mixer 2366 | 2/26/2008 |
| Q: I also have a sunbeam stand mixer model 2366 that stopped operating under a heavier load. I believe ... A: Sunbeam does not make any parts for this mixer. That said, if you can find the fuse it should be ... | |
| Sunbeam Mixmaster Meat Grinder PTU | 2/26/2008 |
| Q: I have a Sunbeam Mixmaster mixer, model number unknown. The only number I can locate on the mixer is ... A: With out a model # I can only guess. The # that you gave me is a part # for the base or stand. The ... | |
| Water Heater | 2/25/2008 |
| Q: Our water heater is only 8 years old and appears to work fine other than we have seen it go a couple ... A: You will probably have to replace the thermostat as it is not operating correctly sometimes. After ... | |
| Replacement handle for mixer | 2/25/2008 |
| Q: I need to know where I can find a replacement handle for a Sunbeam mixer, model # 2360 A: I tried to check Sunbeam's website today and it is not letting me get to the parts diagrams. I do ... | |
| water heater | 2/18/2008 |
| Q: my electric water heater runs out of hot water after about 7 to 8 minutes of a hot shower. both ... A: Check your thermostat setting and see if it may be set too low. Also when someone is taking a ... | |
| Air Compress won't stay running | 2/17/2008 |
| Q: Wayne, I was using my air compressor this fall to blow out my sprinklers. In the middle it died. ... A: The problem probably is a motor problem but try one test first. Make sure the tank has no pressure. ... | |
| Oster Electronic Touch Control Kitchen Center | 2/16/2008 |
| Q: The toucn control pad on my Kitchen Center (978 06B) no longer responds when touched. Is this ... A: I am really surprised that it lasted as long as it did. Oster would not even let us service centers ... | |
| Electric Paper Shredder | 2/16/2008 |
| Q: I've owned and extensively used an inexpensive electric paper shredder for at least five years with ... A: I can not really help you on this question as we do not service shredders because no companies have ... | |
| 3 HEAD OLD HAMILTON BEACH MALTED MACHINE | 2/16/2008 |
| Q: BLENDER WORKS FINE BUT WHEN YOU PUT A CUP ON ANY OF THE 3 HEADS THEY TURN ON BUT WHEN YOU TAKE CUP ... A: If you have the old green HB malt mixer, the switch is located about half way up the stand. The ... | |
| waterheater toubles | 2/14/2008 |
| Q: The pilot light on my water heater won't stay on hat could be the problem? A: You must have a gas water heater and when the thermocouple stops working the pilot light will go out ... | |
| Kitche Aide Standing Mixer | 2/14/2008 |
| Q: We bought our mixer in the US. We now live in China. My daughter accidently plugged it into the ... A: It can be repaired but I think the cost will be more than a new unit. I think they sell for about ... | |
| resistance heat wire | 2/14/2008 |
| Q: I have a Westinghouse portable heater,style#808800-A-CAT.#RM-16. The heating element is a coiled ... A: The only way that I could come close to it is if you would send me the coil. Even then it will not ... | |
| Ice maker problem | 2/7/2008 |
| Q: ice maker model number 80533 the problem is that when the ice has been made its as if the ice tray ... A: I hate to tell you this but I do not think you will be able to get this unit repaired. If it is ... | |
| Mixmaster turntable won't turn | 2/7/2008 |
| Q: My mixmaster turntable won't turn. Isn't it supposed to? If I am supposed to turn it myself, should ... A: Sorry I am so late in getting to you but my computer crashed and I had to borrow one. Yes, it is ... | |
| sunbeam mixmaster 2366 | 2/7/2008 |
| Q: the PC board in my mixer is bad, power is going in but not passing through the speed switch. where ... A: Sorry I am so late in getting to you but my computer crashed and I had to borrow one. You have ... | |
| whirlpool microwave | 2/6/2008 |
| Q: Can I repair the plastic rack holder in my microwave, it burns and flames up when trying to cook ... A: Sorry I am so late in getting to you but my computer crashed and I had to borrow one. You should ... | |
| whirlpool microwave | 2/6/2008 |
| Q: Can I repair the plastic rack holder in my microwave, it burns and flames up when trying to cook ... A: I would contact Whirlpool dealer either on the net or locally and order a new part. You should be ... | |
| Sunbeam Electric Blanket | 2/6/2008 |
| Q: My electric blanket will only get slightly warm. It's practically brand new and I've followed the ... A: Your problem is in the thermostat control but the larger problem is that there are no parts ... | |
| Water Softener | 2/5/2008 |
| Q: I was wondering if you have time to help me with water softener. I have a very old unit that stop ... A: The main thing that usually goes out of older water softeners is the timer motor. Most of these ... | |
| sunbeam mixmaster MM300W | 2/5/2008 |
| Q: Have a sunbeam mixmaster purchased around 1977 numbered as above. The ballbearings in the centre ... A: There is no fix to this problem. Most of the MM mixers did not have a turntable with bearings in ... | |
| sharp replace the door | 2/4/2008 |
| Q: how do i get the door off of a sharp microwave to put the new one on? A: I do not have books on a sharp microwave as we are not a dealer for them. Some units have a plastic ... | |
| T-FAL Avante' Blender | 2/4/2008 |
| Q: I have a T-FAL Avante' blender. Although, the product is works very well (when I am able to use ... A: I am not familiar with T-FAL blenders but if it is like most blenders it has a removable cutting ... | |
| Plug in Rowenta iron makes sparks | 2/4/2008 |
| Q: Everytime I plug in (or out) my new Rowenta iron there are sparks. Why? A: If the sparks are coming from the cord you should not be using the iron. The cord has to be ... | |
| shavers v/s trimmers | 2/4/2008 |
| Q: im a 19 year old teen. i wanted to know the difference between shavers and trimmers. all of the ... A: I would recommend a trimmer for your purpose. I have a Norelco trimmer that will cut from skin ... | |
| Amana Frig. | 2/3/2008 |
| Q: My freezer just stopped working on my 10 yr old, freezer in the bottom Amana Frig. Needless to say ... A: If it keeps running and doesn't cool there could be many problems but it sounds like you could be ... | |
| kitchenaid K45SS | 2/3/2008 |
| Q: I think I have this model--it's my Mom's from 1971 that's been passed down to me. I ran it with an ... A: There is a small speed control board that sometimes goes bad in these units but I am only guessing. ... | |
| Sunbeam Toaster Model 6329 | 2/2/2008 |
| Q: The bread tray in this toaster will no longer stay down. I think the electromagnet is defective. It ... A: I am afraid that you have fallen victim to the "Made in China Syndrome". Sunbeam stopped making ... | |
| Misaligned beaters on Sunbeam Heritage Series Stand Mixer... | 2/2/2008 |
| Q: I read the question and answer about realigning the beater gears... How do I get the front off? I've ... A: Sunbeam made a number of Heritage series mixers through the years so I do not know which one you ... | |
| JENN-AIR MICROWAVE QUESTION | 1/31/2008 |
| Q: I HAVE A JENN-AIR MODEL M169B MICROWAVE THAT WON'T WORK. I AM VERY PROFICIENT AT READING PRINTS, AND ... A: You have to be an authorized service center to have access to any Jenn-air literature and we are ... | |
| CABINET LIGHTING FOLLOW UP QUESTION | 1/30/2008 |
| Q: HERE IS SOME ADDITIONAL INFO.THE TRANSFORMER I AM USING IS AN AC/DC ADAPTOR, INPUT 120V AC, 60HZ ... A: You are correct. You should have one that will supply over 100 watts as you should have a little ... | |
| Portable heater | 1/30/2008 |
| Q: Every 1500W portable heater coils will stop glowing red after awhile. Is the heater still putting ... A: I would recommend a Lakewood or Lasko heater as, I think, they are still made in the U.S. ... | |
| steam iron sprays water instead of steam | 1/29/2008 |
| Q: My steam iron sprays water when I press the steam button. Any idea why that would happen? Thanks A: The main problem that most steam irons have is that they do not heat hot enough to steam and then ... | |
| CABINET LIGHTING FOLLOW UP QUESTION | 1/29/2008 |
| Q: HERE IS SOME ADDITIONAL INFO.THE TRANSFORMER I AM USING IS AN AC/DC ADAPTOR, INPUT 120V AC, 60HZ ... A: Either your transformer is too small for the amount of bulbs you are trying to light or you are ... | |
| Tfal Toaster | 1/28/2008 |
| Q: I have a Tfal toaster I'm repairing. There is a small circuit board that has a large resistor, ... A: I am not sure if Tfal makes any parts for their appliances but you can try to contact "Fox ... | |
| Sunbeam mixmaster model 9 coil removal | 1/28/2008 |
| Q: How does one go about removing the coil from a mixmaster model 9. I want to strip and repaint. ... A: The capacitor should be accessible from from the back of the unit. I have both resistors and ... | |
| Sunbeam mixmaster model 9 coil removal | 1/28/2008 |
| Q: How does one go about removing the coil from a mixmaster model 9. I want to strip and repaint. ... A: You should not have to remove it to repaint the case. Sometimes when they are removed, they do ... | |
| Sunbeam Toaster | 1/26/2008 |
| Q: I would like to know if I can send an old toaster to you for repairs. It has stopped working and I ... A: We repair many of these old toasters each week. They were the best toaster Sunbeam ever made. ... | |
| UNDER CABINET LIGHTING | 1/26/2008 |
| Q: I ACQUIRED A CABINET WITH FOUR 12 VOLT, 10 WATT UNDER CABINET LIGHTS THAT ARE ON AN ELECTRICAL CORD ... A: Most of these lights operate on either 12 volts a.c. or 12 volts d.c. I do not know which one you ... | |
| Black & decker under the counter toaster | 1/8/2008 |
| Q: Where may I purchase a heating element for the above toaster. I want to repair it. 11" long, 750 ... A: The only company selling B & D appliance parts is Fox International. They have a website but you ... | |
| sears microwave oven | 1/7/2008 |
| Q: We have a sears spacemaster microwave oven and it stopped working. Now it does absolutely nothing. ... A: If everything is dead, that is a good sign. There is probably just a fuse that is blown. If you ... | |
| Sunbeam Mixmaster Heritage Series - Legacy Edition S | 1/6/2008 |
| Q: We have had the above unit for over a year now and the other day my wife was using the machine to do ... A: I think you are experiencing what a lot of Americans are experiencing. These new Sunbeam mixers are ... | |
| Thermostat For B&D DE755B Coffee Maker | 1/6/2008 |
| Q: Black & Decker 12 Cup Coffee Maker DE755B Question The thermostat is blown. The numbers on the fuse ... A: We are not authorized for B & D so I donot have parts book for your unit. The # that is important ... | |
| Microwave stain removal.. | 1/5/2008 |
| Q: I have tried all the tips found on the internet,but nothing works for removing brown mottled stains ... A: It looks to me like the paint was not put on the unit properly at the factory. It is getting thin ... | |
| Sunbeam Mixmaster 60th Anniversary | 1/5/2008 |
| Q: just found your site and hope you can help me out. my mother just gave me the mixer for christmas ... A: If you had the white bowls, they are not available new but I do have new clear bowls that will fit ... | |
| New electric radiant heater tr ips Ground Fault outlet | 1/5/2008 |
| Q: When I plug my new radiant heater into a Ground Fault outlet and turn it on it trips the GF outlet. ... A: GFI outlets are sensitive to current balances in a circuit and will trip much faster that a regular ... | |
| doremeyer silverbullet mixer | 1/4/2008 |
| Q: something has gone awry with my keyboard so i am not able to type many things: including numbers and ... A: I do have some replacement beaters for Dormeyer but will have to see a picture of your old ones to ... | |
| Microwave stain removal.. | 1/4/2008 |
| Q: I have tried all the tips found on the internet,but nothing works for removing brown mottled stains ... A: When food gets on the sides of a microwave, the waves will concentrate on it. This will stain and ... | |
| CFL bulbs | 1/3/2008 |
| Q: It is I again. My reading lamp has a single 3-way (50-100-150) bulb. I have tried the highest # CFL ... A: As long as you have good ventilation for the bulbs there should not be a problem using two 23 watt ... | |
| Hamilton Beach Milkshake Mixer | 1/3/2008 |
| Q: I have an OLD HB milkshake mixer. Probably from the 40's/50's. It was working great...until last ... A: We will be glad to look at your unit. It could be a lot of things. If you will send us the unit ... | |
| T-FAL Toaster oven | 1/3/2008 |
| Q: I have a T-FAL toaster oven that suddenly stopped working. The oven is a 4 year old Avante Elite. ... A: There has to be a fuse but it could be on the circuit board. It should be on the incoming power ... | |
| Beaters for Dormeyer Model 4300 Silver Chef mixer | 1/1/2008 |
| Q: My parents have a Dormeyer Model 4300 Silver Chef mixer that needs new beaters. Do you have beaters ... A: This is one of the most common Dormeyer mixers so I have been out of beaters for years. I do have ... | |
| sunbeam toaster-matic model AT-40 | 1/1/2008 |
| Q: I have attempted to have this old toaster repaired. No one is interested, including approved Sunbeam ... A: We probably service 100 of these every year. They are not easy to work on and that is why repair ... | |
| Need heating elements for OLD GE toaster oven | 1/1/2008 |
| Q: Do you remember the old GE toaster ovens? The small ones that when you open the door the tray ... A: I may still have some for this unit. If you can give me the measurement on the inside of the oven ... | |
| roaster handle | 12/31/2007 |
| Q: Wayne, I have an old Westinghouse roaster oven. The only number I could find on the unit is ... A: I think you will h | |