| Subject | Date Asked | Expert |
|
| m11 | 10/31/2009 | Waheed Shittu |
Q: What is the difference between celect and stc. In order to set the valves and injectors. ISM 370
A: Celect is simply a system developd by Cummins to electronically manage an engine. it consists of an ...
|
| valve & Inj. setting/n-14 plus cumming | 10/23/2009 | Waheed Shittu |
Q: Do I have to move the timing letters a, b,and c 360 degrees for each valve setting? Making a total ...
A: No, pls find the correct order: Vs Mark Injector Valve A 1-6 VS 3 5 B ...
|
| Cummins M11 | 10/22/2009 | Waheed Shittu |
Q: We have a truck w/ M11 celect plus with a skip had a fault code ( inactive) P332 no voltage on ...
A: Greg, I have copied the following for your perusal. I dont think it was an inactive fault with the ...
|
| valve & Inj. setting/n-14 plus cumming | 10/21/2009 | Waheed Shittu |
Q: Do I have to move the timing letters a, b,and c 360 degrees for each valve setting? Making a total ...
A: Cylinders in a 6 cylinder engine are numbered 1,2,3,4,5,and 6 from the front of engiine to the rear. ...
|
| n14 | 10/20/2009 | Waheed Shittu |
Q: sir good day i woul to ask about how to adjust the valve and injectors of n14 cummins thanks ...
A: That was an STC injector. The setting is different from the other injector types. It is a zero lash ...
|
| M11 | 10/19/2009 | Waheed Shittu |
Q: I am an old bus driver who runs mostly detroit and some cats...i am considering buying a motorhome ...
A: My general experience locally here in Nigeria on Cummins M11 has to do with difficulty in ...
|
| valve & Inj. setting/n-14 plus cumming | 10/19/2009 | Waheed Shittu |
Q: Do I have to move the timing letters a, b,and c 360 degrees for each valve setting? Making a total ...
A: No Felix. you need only two revolutions to complete the setting of the six cylinders. If you start ...
|
| 1990 L10 Smokes | 10/14/2009 | Waheed Shittu |
Q: I have a 1990 L10 Cummins, 270 hp with top stop injectors. The engine smokes fairly good at an idle ...
A: On the persistent smoke, I advice the following: 1. Check and clean out the air filter or replace ...
|
| 2000 n-14 hard to start. | 10/13/2009 | Waheed Shittu |
Q: !! first off i parked my 2000 kw n-14 cummins for a few months.why things were real slow. i just put ...
A: Really a puzzle. Havig done all of the above, I advise that you check fuel inlet line from the tank ...
|
| 1990 L10 Smokes | 10/12/2009 | Waheed Shittu |
Q: I have a 1990 L10 Cummins, 270 hp with top stop injectors. The engine smokes fairly good at an idle ...
A: Smoking especially on a turbocharged engine during the commencement of acceleration is normal. It is ...
|
| M11 Help | 10/6/2009 | Waheed Shittu |
Q: Im working on a 1994 cummins m11 Ive got power to the ecm and fuel sender but the truck will not ...
A: To help find probable solution to this problem, you need to clarify the following; 1. Does the ...
|
| 855 cummins | 10/4/2009 | Waheed Shittu |
Q: I have a 855 cummins big cam in a ford 976 tractor, i bought the tractor last fall used it for a ...
A: From experience, I know that overheating due to malfunction of the cooling system may lead to ...
|
| Flatbed Trucks | 10/4/2009 | Waheed Shittu |
Q: I want to go into haulage business. I am discussing with my in-laws in US in getting a mack flatbed ...
A: Bunmi, 1. I believe that the kind of glue you mentioned will not endanger any of the truck ...
|
| Cummins N14 | 9/22/2009 | Waheed Shittu |
Q: I have a small fleet in Nigeria. I wanted to purchase a Freightliner with an N14 engine but was ...
A: Shehu, The reality of the current situation in Nigeria with regards to proper diagnosis of engines ...
|
| Cummins 5.9 ISB Fuel line leak | 9/15/2009 | Waheed Shittu |
Q: I had a fuel airlock on a 2000 Cummins 24 valve 5.9 ISB after draining the water in fuel seperator ...
A: Air lock occurs as a result of opening, loose fittings and joints or cracks in the high pressure ...
|
| n14 cummins 1998 | 9/10/2009 | Waheed Shittu |
Q: have oil leak at the back of the motor can't tell if its the rear main seal just start to leak last ...
A: If the oil leakage is coming out between the flywheel housing and the engine block, it is most ...
|
| n14 | 9/4/2009 | Waheed Shittu |
Q: sir good day i woul to ask about how to adjust the valve and injectors of n14 cummins thanks
A: The basic rule is to check the engine data plate for information on the type of injector adjustment ...
|
| Truck shut down | 9/2/2009 | Waheed Shittu |
Q: 1997 Volvo with a M-11 Cummins Motor- Why does my truck jerk and act like it is going to shut down? ...
A: I can offer the following advise. 1 Check the quality of your diesel fuel. 2. Clean your fuel tank ...
|
| cummin n-14 | 9/1/2009 | Waheed Shittu |
Q: A customer complains about low power condition on a cummins n-14 when under a load. what would be ...
A: troubleshooting a low power complaint is exhaustive. However, you can find answer to the following ...
|
| 1988 or 89 855 Cummins big cam | 8/21/2009 | Waheed Shittu |
Q: .. My brother has a dumptruck with a 1988 or 89 Cummins 855 big cam engine that has suddenly ...
A: Jodi, I need to clarify the oil pressure value you quoted is it the same as 10 p.s.i and 21 p.s.i. ...
|
| 6.0 Liter Hard Start | 8/15/2009 | Waheed Shittu |
Q: I have an '06 6.0L F-350 with 97k miles. About 2 weeks ago it began having hard starts. If left for ...
A: Hard starting can occur due to a variety of reasons among which are: 1. Poor fuel quality 2. Air in ...
|
| fault codes | 8/13/2009 | Waheed Shittu |
Q: I have a customers truck in my workshop with an isc 300 that has intermittent fault codes appearing. ...
A: Adam, i have sent you a reply a couple of days ago on this question perhaps you did not receive it. ...
|
| F250 7.3l POWERSTROKE | 8/11/2009 | Waheed Shittu |
Q: 1995 model F250 7.3l powerstroke engine After the truck has been shut off for a period of time (2 or ...
A: When you shutdown an engine, fuel stops going to the injectors. However, most diesel system are ...
|
| F250 7.3l POWERSTROKE | 8/10/2009 | Waheed Shittu |
Q: 1995 model F250 7.3l powerstroke engine After the truck has been shut off for a period of time (2 or ...
A: Hard starting can occcur through the following 1. Air in the fuel system 2. Faulty fuel return ...
|
| 2000 freightliner classic | 8/8/2009 | Waheed Shittu |
Q: what could be wrong with my truck. the engine keeps shutting down, then the check engine oil light ...
A: My advise is for you to get the engine properly diagnosed with the "insite" software at a cummins ...
|
| active and inactive faults on Cummins N14 engine | 8/6/2009 | Waheed Shittu |
Q: ECM#22910 ENGINE# 11889458 COULD YOU PLS HELP ME SOLVE THIS PROBLEM ON THIS TRUCK AND BELOW ARE ...
A: I did answer this question in detail yesterday but it disappeared with a "prompt 65,000 character ...
|
| Cummins N14 Using Oil | 8/5/2009 | Waheed Shittu |
Q: My driver reports that his truck has used 4 gallons of oil in the past 3 days. He does not see any ...
A: I need to have answer to the following questions. 1. What is the present speedo reading on truck and ...
|
| cummins n14 | 8/3/2009 | Waheed Shittu |
Q: have n14 cpl 1807 needs overhauled calls for two piece piston can a one piece piston be used if so ...
A: Steve, I strongly advise against the use of non-conformed parts for overhaul as this will have a ...
|
| 2002 dodge ram problem | 7/27/2009 | Waheed Shittu |
Q: I have a 2002 dodge ram 6 speed diesel truck. When I'm driving it, it stalls on hiway if I ...
A: If your throttle control is electric, you may have to check the acceleration sensor fitted beside ...
|
| white smoke when low speed | 7/26/2009 | Waheed Shittu |
Q: We have a generator set model VTA 28-G2 ( timing code R ). After we replace fuel injectors and ...
A: I have sent an answer on this question before, I don't know if you received it. However, you should ...
|
| question | 7/24/2009 | Waheed Shittu |
Q: valves adjusments steps in N14 cummins
A: You have on the accessory drive pulley timing marks A,B, and C or 1-6vs; 2-5vs; and 3-4vs. Rotate ...
|
| m11 celect | 7/21/2009 | Waheed Shittu |
Q: good day,im a mechanic from philippines,m11 cummins starter motor was constantly running because of ...
A: The first step towards solving your problem is to hook it on "insite software" or "compulink" for ...
|
| Engine light | 7/20/2009 | Waheed Shittu |
Q: Hey, I realize that you are not a Dodge man but maybe you can still help me. My 02 Dakota Sport is ...
A: Fault codes troubleshooting requires that one has the details particular to it to have a successful ...
|
| cummins N14 celect | 7/20/2009 | Waheed Shittu |
Q: My Cummins MN truck would not start until a WD40 spray is sprayed in the air cleaner hose for a ...
A: When you frequently use start aid, this indicates that you need to check your fuel injection system. ...
|
| wont start | 7/19/2009 | Waheed Shittu |
Q: i have a frieghtliner dump truck with as cummins M11 celect engine it hasd sat for about a month and ...
A: Cummins M11 Celect engines ECM will display some flash codes to indicate that the ECM is bad. You ...
|
| m11 cummins | 7/18/2009 | Waheed Shittu |
Q: What are the head bolt torqe specs. Also will an injector o-ring cause hard start
A: The head bolt torque specs is as follows: 3 steps 1 100 ft-ib or 136 N.m 2 160 ft-lb or 217 N.m 3 ...
|
| Cummins N14 engine | 7/17/2009 | Waheed Shittu |
Q: At what temperature should a healthy Cummins N14 engine run at?(water temp)
A: A 'healthy' Cummins N14 cooling system is expected to run as specified: Min. Recommended operating ...
|
| Engine replacement how long | 7/15/2009 | Waheed Shittu |
Q: My mother has a dodge cummins diesel 6.7L I beleive it is only a few years old. The motor recently ...
A: If the intention is to diagnose and replace, and contingent upon the availability of spares, the ...
|
| fuel injector | 7/3/2009 | Waheed Shittu |
Q: I HAVE A 1998 DODGE DAKOTA 3.9 WITH A BAD FUEL INJECTOR COULD THIS CAUSE THE TRUCK TO LOSE POWER & ...
A: Yes, a bad injector can cause an engine to lose power. injector can go bad as a result of 1. ...
|
| 855 cummins diesel engine | 7/1/2009 | Waheed Shittu |
Q: I have an 855 cummins diesel engine on a Versatile farm tractor. The engine is a 1980 year model big ...
A: Fuel dilution with engine oil can occur as a result of 1. Injector wear (barrel plunger wear) 2. ...
|
